PTC04-DBHall Daughter Board for Melexis PTC devices Features and Benefits PTC04 interface board for testing devices 90215 90224 90244 90251 90277 Applications Experimental tool for Lab and Prototyping Production Equipment for Serial Programming Ordering Information Part No. PTC04-DBHall Description Default Daughter Board (Board + rear panel PTC04) Accesoires Part No. DLL’s for all supported products User Inter Faces for supported products Description 1. Functional Diagram PTC04-DBHall Rev. 1.0 Page 1 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices TABLE OF CONTENTS FEATURES AND BENEFITS ...................................................................................................................1 APPLICATIONS.......................................................................................................................................1 ORDERING INFORMATION ....................................................................................................................1 ACCESOIRES..........................................................................................................................................1 1. FUNCTIONAL DIAGRAM .................................................................................................................1 2. BOARD DESCRIPTION ....................................................................................................................3 2.1. BOARD LAYOUT ....................................................................................................................................... 3 2.2. DESCRIPTION ........................................................................................................................................... 4 2.3. DAUGHTER BOARD CONNECTORS .............................................................................................................. 5 2.3.1. Digital DB Connector (40 Pins)........................................................................................................ 5 2.3.2. Analog DB Connector (48 Pins) ....................................................................................................... 6 2.4. APPLICATION CONNECTOR........................................................................................................................ 7 3. DISCLAIMER....................................................................................................................................8 PTC04-DBHall Rev. 1.0 Page 2 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices 2. Board description 2.1. Board Layout Figure 2-1 • • • • • J1 : Jumpers to connect the measurement sense lines immediately to the force lines. These jumpers are needed when no force and sense is used. J3,J4 : These jumpers are future expansions in order to support PWM output measurements and are not needed for testing the 90251 or the 90277. DB-ID : This ID keeps a few initial variables in mind. It allows for example to detect what DB is connected to the programmer and if the DB is not expired. Analog and Digital connector : See below for a detailed description DB Connector : Connector to the application. See below for details PTC04-DBHall Rev. 1.0 Page 3 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices 2.2. Description +5V_D IG_CON IO_0 IO_1 IO_2 IO_3 IO_4 IO_5 IO_6 IO_7 U1 1 2 3 4 5 6 7 8 9 I1 I2 I3 I4 I5 I6 I7 I8 GND ULN2803LW DGND 18 17 16 15 14 13 12 11 10 O1 O2 O3 O4 O5 O6 O7 O8 VCC IOdrv _0 IOdrv _1 IOdrv _2 IOdrv _3 IOdrv _4 IOdrv _5 IOdrv _6 IOdrv _7 +5V_D IG_CON R1 1 D1 2 R3 1K 1 D2 2 R4 1K 1 D5 2 R5 1K 1 D6 2 R6 1K 1 D7 2 R8 1K 1 D8 2 R9 1K 1 D9 2 R 10 1K1 D10 Vout_PPS1 D3 1 +5V_DIG_C ON 2 2 1N 4001 D4 R2 1 10K SC L SD A 8 7 6 5 U2 VDD PTC SCL SDA PCF8582AP I2C address : 1010 0000 DGND 2 DGND DG ND C1 1 +5V_D IG_CON 100NF_Z 5U 5 2 2 PE5 1 PE6 1 J3 D0 D1 D2 D3 D4 D5 D6 D7 3 4 7 8 13 14 17 18 FA 1 11 D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 OC G VCC GND IO_0 IO_1 IO_2 IO_3 IO_4 IO_5 IO_6 IO_7 2 5 6 9 12 15 16 19 20 10 IOdrv _4 3 JU MPER 2 Vout_PPS1 10K JU MPER +5V_DIG_C ON Pickering 109-2-A-5/2D R 11 2 R EL2 6 1 R12 U3 OU T_DIE_1 4 2K2 J4 1 2 3 4 A0 A1 A2 VSS 6 1 R7 1K +5V_D IG_CON R EL1 1N4148 5 2 OU T_DIE_2 IOdrv _5 4 2K2 3 +5V_DIG_C ON 1 D 11 1N 4001 2 2 D12 +5V_DIG_C ON Pickering 109-2-A-5/2D 1 1N4148 +5V_DIG_C ON 74H CT373 DGND ISEN SE_PPS1 ISEN SE_PPS2 ISEN SE_PPS3 ISEN SE_PPS4 AN A.COMP0 AN A.COMP2 A GND CON48B +2.5V_R EF_SU PPLY J2 VD D_SENSE_DIE_1 OUT_SENSE_D IE_1 VD D_SENSE_DIE_2 OUT_SENSE_D IE_2 J7 VDD_D IE_1 VD D_SENSE_DIE_1 MEMO_DIE_1 GND_SENSE_DIE_1 GND_D IE_1 OUT_SEN SE_D IE_1 OUT_DIE_1 VDD_D IE_2 VD D_SENSE_DIE_2 MEMO_DIE_2 GND_SENSE_DIE_2 GND_D IE_2 OUT_SEN SE_D IE_2 OUT_DIE_2 GND_SENSE_DIE_1 GND_SENSE_DIE_2 +36V +5V_ANA_C ON VOUT_PPS1 VOUT_PPS2 VOUT_PPS3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 J1 2 4 6 8 10 12 VD D_D IE_1 GN D_D IE_1 OU T_DIE_1 VD D_D IE_2 GN D_D IE_2 OU T_DIE_2 1 3 5 7 9 11 VDD _SEN SE_D IE_1 GN D_SENSE_D IE_1 OU T_SEN SE_DIE_1 VDD _SEN SE_D IE_2 GN D_SENSE_D IE_2 OU T_SEN SE_DIE_2 VD D_SENSE_DIE_2 GND_SENSE_DIE_2 OUT_SENSE_D IE_2 Jumper H EADER 6X2 A GND VOUT_PPS4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VDD_D IE_1 MEMO_DIE_1 GND_DIE_1 OUT_D IE_1 VDD_D IE_2 MEMO_DIE_2 GND_DIE_2 OUT_D IE_2 VD D_SENSE_DIE_1 GND_SENSE_DIE_1 OUT_SENSE_D IE_1 DB15 Clamped on edge of PC B SH TD_PPS1 SH TD_PPS2 SH TD_PPS3 SH TD_PPS4 PR O1 PR O5 PR O2 PR O6 PR O3 PR O7 PR O4 PR O8 +36V_SUPPLY +5V_SUPPLY 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 14 pins Screw_terminal 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 A GND J5 A GND AN A.COMP1 AN A.COMP3 A GND Vout_PPS1 VDD _DIE_1 REL3 +5V_DIG_C ON J6 DIGITAL DB CONNECTOR1 A0 A2 A4 A6 D0 D2 D4 D6 Rd SCL F8 FA FC FE PE0 PE2 PE4 PE6 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 40 Pin Header A1 A3 A5 A7 D1 D3 D5 D7 Wr R eset SD A F9 FB FD FF PE1 PE3 PE5 PE7 +5V_D igital_Supply Vout_PPS2 1 IOdrv _2 2 3 4 OU T_DIE_1 R EL4 PIC KER IN G 112-1-A-5/2D 2 1 7 5 3 REL6 +5V_DIG_C ON Vout_PPS3 1 IOdrv _3 2 3 VDD _DIE_2 IOdrv _0 +5V_DIG_C ON Pickering 108-1-C -5/3D 1 7 5 3 PIC KER IN G 112-1-A-5/2D R 13 Vout_PPS4 OU T_DIE_2 IOdrv _1 +5V_DIG_C ON Pickering 108-1-C -5/3D MEMO_D IE_1 100 R 14 +5V_DIG_C ON DGND R EL5 2 4 MEMO_D IE_2 100 Size A3 Date: PTC04-DBHall Rev. 1.0 Page 4 of 8 Project : 90277\90251\90244\90215 Schematic : Template - D aughter Board Sheet Tuesday , March 30, 2004 1 of R ev 001 1 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices 2.3. Daughter board Connectors The main board has two connectors to the interface with the application. The PTC allows to add a full PCB in between. This daughter board can be mounted on the two connectors. In some exceptional cases, a daughter board contains only a few wires from the Analog connector to the application connector The connection on the connectors are described below Digital DB Connector A0 A2 A4 A6 D0 D2 D4 D6 Rd SCL F8 FA FC FE PE0 PE2 PE4 PE6 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Analog DB Connector A1 A3 A5 A7 D1 D3 D5 D7 Wr Reset SDA F9 FB FD FF PE1 PE3 PE5 PE7 +5V_Digital_Supply 40 Pin Header DGND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 SHTD_PPS1 SHTD_PPS2 SHTD_PPS3 SHTD_PPS4 ISENSE_PPS1 ISENSE_PPS2 ISENSE_PPS3 ISENSE_PPS4 ANA.COMP0 ANA.COMP2 A GND 2.3.1. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 48 pin Header ExtMeas1Pos ExtMeas2Pos ExtMeas3Pos ExtMeas4Pos ExtMeas1Neg ExtMeas2Neg ExtMeas3Neg ExtMeas3Neg +36V_SUPPLY +5V_Analog_SUPPLY +2.5V_REF_Voltage VOUT_PPS1 VOUT_PPS2 VOUT_PPS3 VOUT_PPS4 ANA.COMP1 ANA.COMP3 A GND Digital DB Connector (40 Pins) Mainly, the digital connector is meant to expand the programmer to extra needs. Address lines A0-A7 together with the Map Select Lines F8-FF allows to direct access an area of 2 K Examples would be adding a simple addressed I/O register by using the selection lines. If more complexity is needed, a full FPGA can be mounted on the DB board Pins 1–8 9 – 16 17 18 20 Names A0 – A7 D0 – D7 Rd Wr Reset 21-22 23-30 31-38 SCL / SDA F8,F9,…,FF Port E PTC04-DBHall Rev. 1.0 Description Address lines Data Lines active during Rd or Wr signals Read : A negative pulse will indicate a sampling of the data on the Data Bus Write : A Negative pulse will indicate when data is available on the Data Bus This signal goes low by powering the PTC or by pressing the reset button. This line can be pulled low by application. Check firmware documentation for resetting by software. I2c Bus CS lines when the address areas are accessed Note: These pins are limited to 5 Volt input\output!!!! Page 5 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices The full Port E of the Atmega core is mounted to these pins. This allows us to use advanced features like PWM, UARTS, Time Measurements, etc…. By using firmware that supports these, functions, really nice application specific requirements can be fulfilled. 39 Dgnd Digital Ground 40 +5V Digital 5 Volt Digital Supply. Maximum current to get out of this supply : ….mA Note: All the pins are limited to 5 Volt input\output!!!! However, there are Protections, please take precautions in order to avoid damage of the main board. 2.3.2. Analog DB Connector (48 Pins) Mainly, the analog connector provides all the analog signals and measure possibilities. Pins 28,32,36 40 27,31,35,39 Names PPS 1-3 PPS 4 Isense_PP1-4 Description Output of the Programmable Supplies Output of the Fast DAC Programmable Power Supply Outputs (Driver outputs before Rsens) for current evaluations. These outputs could be used to connect to the analog comparators in order to create fast digital signals based on current. 2,4,6,8 ExtMeas1-4Pos There are 4 differential inputs for making measurements 10,12,14,16 ExtMeas1_4Neg The negative inputs of ExtMeas1-4Pos 17,19,21,23 Shtd_PPS1-4 Outputs that shows the status of the Drivers. Signals are meant to connect LED's to put the front panel 43,44,47,48 AnaComp0-3 See *Note. Input (limited to 5V) Fast Level comparators in order to remove time consuming measurement 18 +35V_Supply Supply to extend the daughter board with some extra drivers 20 +5V_Analog Supply to extend the daughter board with some extra hardware 24 +2.5V Ref Output of internal reference All other AGND Analog Ground Note: All the pins are limited to 35 Volt input\output!!!! However, there are Protections, please take precautions in order to avoid damage of the main board. * Note: Some pins are protected and limited to 5 Volt!!!! However, there are Protections, please take precautions in order to avoid damage of the main board. PTC04-DBHall Rev. 1.0 Page 6 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices 2.4. Application Connector Pins 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Names VDD A MEMO A VSS A OUT A VDD B MEMO B VSS B OUT B SENSING VDD A SENSING VSS A SENSING OUT A NC SENSING VDD B SENSING VSS B SENSING OUT B PTC04-DBHall Rev. 1.0 Description Supply Device A Analog Ground Device A Output Device A Supply Device B Analog Ground Device B Output Device B Sensing Supply Device A Sensing Analog Ground A Sensing Output Not Connected Sensing Supply Device B Sensing Analog Ground B Sensing Output Device B Page 7 of 8 Data Sheet PTC04 Apr/04 PTC04-DBHall Daughter Board for Melexis PTC devices 3. Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering of technical or other services. © 2002 Melexis NV. All rights reserved. For the latest version of this document, go to our website at: www.melexis.com Or for additional information contact Melexis Direct: Europe and Japan: Phone: +32 13 67 04 95 E-mail: [email protected] PTC04-DBHall Rev. 1.0 All other locations: Phone: +1 603 223 2362 E-mail: [email protected] Page 8 of 8 Data Sheet PTC04 Apr/04 QS9000, VDA6.1 and ISO14001 Certified