dm00158090

TN1208
Technical note
Tape and reel shipping media for STM8 and STM32
microcontrollers in TSSOP and SSOP packages
Introduction
TSSOP and SSOP packages can be supplied in tape and tube shipping media.
The reels have a 13” typical diameter.
The types of reel used are in plastic either anti static or conductive, with a black conductive
cavity tape. The cover tape is transparent anti static or conductive.
The devices are positioned in the cavities with the identifying pin (normally Pin “1”) on the
same side as the sprocket holes in the tape.
STMicroelectronics tape and reels are compliant with EIA 481 and IEC 60286-3 standard
specifications.
Table 1 lists TSSOP and SSOP packages available for STM8 and STM32 microcontrollers,
as well as the corresponding shipping media.
Table 1. TSSOP and SSOP packages available in tape and reel packing
Package
Reel
code
diameter
Package
Description
SSOP 16
SSOP 16 5.3 mm
SF
SSOP 28 10.2x5.3
SSOP 28 10.2x5.3 mm
B2
TSSOP 20
TSSOP 20 BODY 4.4 PITCH 0.65
YA
March 2015
DocID027436 Rev 1
13”
Tape
width
Tape
pitch
16 mm
12mm
16 mm
12 mm
16 mm
12 mm
1/13
www.st.com
1
Contents
TN1208
Contents
1
Reel description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Leader and trailer tape specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Device orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Carrier tape mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6
Bending radius requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7
Camber requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2/13
DocID027436 Rev 1
TN1208
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
TSSOP and SSOP packages available in tape and reel packing . . . . . . . . . . . . . . . . . . . . . 1
Reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Carrier tape constant dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Carrier tape variable dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DocID027436 Rev 1
3/13
3
List of figures
TN1208
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
4/13
Reel diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Leader and trailer tape schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Labeling location on reel for carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Device orientation on tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Embossed carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bending radius requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Camber requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DocID027436 Rev 1
TN1208
1
Reel description
Reel description
Figure 1. Reel diagram
)LJXUH
069
Table 2. Reel dimensions(1)
A
max.
Reel
size
(inch)
Tape
size
(mm)
(mm)
13
16
330
Reeds without drive hole
B min.
(mm)
1.5
C (mm)
13.0+0.5/0.2
Reeds with drive hole
D min. B min.
(mm) (mm)
20.2
NA
C max.
(mm)
D min.
(mm)
29.2
NA
N(mm) W1(mm)(2)
100
178±5
16.4+2/-0
W2
max.
(mm)
22.4
1. NA stands for “not applicable”.
2. W1 is measured at the hub.
DocID027436 Rev 1
5/13
12
Leader and trailer tape specifications
2
TN1208
Leader and trailer tape specifications
The leader has a minimum width of 400 mm which includes at least 100 mm of carrier tape
with empty cavities and sealed cover tape (see Figure 2). The leader tape is affixed to the
last turn of carrier tape by using a transparent adhesive anti static or paper based tape of a
width not higher than the one of the cover tape.
The trailer is a carrier tape which minimum width is 160 mm with empty cavities and sealed
cover tape, as shown in Figure 2. The trailer tape must be affixed to the reel by using the
tape slot of the reel hub.
During the unwinding operation, the entire carrier tape must be easily released from the reel
hub as the last portion of the tape unwinds from the reel without damaging the carrier tape
and the remaining components in the cavities.
Figure 2. Leader and trailer tape schematics
6/13
DocID027436 Rev 1
TN1208
3
Labeling
Labeling
STMicroelectronics “inner box” standard label is placed on each reel at the following
locations:
•
On the box that directly holds the reel
•
On the damp proof bag if the units are dry packed
•
On the reel itself
The label is attached to the flange that is facing the user when the tape is extracted
from the reel at the top right (see Figure 3).
Figure 3. Labeling location on reel for carrier tape
DocID027436 Rev 1
7/13
12
Device orientation
4
TN1208
Device orientation
The largest axis of the component outline is perpendicular to the tape length.
The device is positioned in the carrier tape cavity as shown in Figure 4: Device orientation
on tape. Pin 1 is located on the top left corner of the package.
Figure 4. Device orientation on tape
86(5',5(&7,212))(('
069
8/13
DocID027436 Rev 1
TN1208
5
Carrier tape mechanical dimensions
Carrier tape mechanical dimensions
The width is 16 mm (refer to Table 1: TSSOP and SSOP packages available in tape and reel
packing).
Figure 5. Embossed carrier tape
Table 3. Carrier tape constant dimensions
Tape
width
D0
D1 min
E1
P0
P2
R(1)
S1
16 mm
1.5+0.1
/-0.0
1.5
1.75±0.1
4.0±0.1
2.0±0.1
30
0.6
T max. T1 max.
0.6
0.1
Unit
mm
1. The maximum radius the tape with or without components can bend without damage is specified in Section 6: Bending
radius requirements.
Table 4. Carrier tape variable dimensions
Tape
width
B1
E2
F
P1
T2 max.
W max.
A0, B0, K0
Unit
16 mm
12.1
14.25
7.5±0.1
4.0±0.1 to
12.0±0.1 by 4.0
increments
8.0
16.3
See (1)
mm
1. The cavity defined by A0, B0 and K0 surrounds the component with sufficient clearance so that:
- The component does not protrude above the top surface of the carrier tape.
- The component can be removed vertically from the cavity without mechanical restriction, after the top cover tape has been
removed.
- Rotation of the component is limited to 20° maximum for 12 mm tapes and to 10° maximum for 16 mm and 24mm tapes.
- Lateral movements of the component are restricted to 0.5 mm maximum for 12 mm tapes and to 1.0 mm maximum for
16 mm and 24 mm tapes.
DocID027436 Rev 1
9/13
12
Bending radius requirements
6
TN1208
Bending radius requirements
Figure 6. Bending radius requirements
10/13
DocID027436 Rev 1
TN1208
7
Camber requirements
Camber requirements
Carrier camber should not exceed more than 1 mm in 250 mm of carrier tape length.
Figure 7. Camber requirements
DocID027436 Rev 1
11/13
12
Revision history
8
TN1208
Revision history
Table 5. Document revision history
12/13
Date
Revision
17-Mar-2015
1
Changes
Initial release.
DocID027436 Rev 1
TN1208
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
DocID027436 Rev 1
13/13
13