TAPE & REEL

TAPE & REEL
Specifications
REEL OUTLINE DIMENSIONS
■ Tape and reel specifications for all
components shall conform with
International standard IEC 60286-3
■ Peel force and speed of cover tape;
0.1-1.3N @300mm±10mm/MIN, the
angle between the cover tape during
peel-off and the direction of unreeling
shall be 165-180°.
■ The break force of the cover tape
shall be 10N MIN.
■ The carrier tape leader section shall
include a minimum 100mm length of
empty carrier tape sealed by the
cover tape (see fig 1).
■ The maximum number of missing
components shall be one or 0.1%,
whichever is greater. In no case shall
there be two or more consecutive
components missing.
■ The trailer section shall consist
entirely of empty carrier tape sealed
by the cover tape.
Order Code
Reel Quantity
DA10XM
Reel Outline Dimensions
Figure
N
W1
W2
W3
500
60
24.4
30.4
23.9–27.4
NTAXXXXM-R
500
60
24.4
30.4
23.9–27.4
NTEXXXXM-R
500
60
24.4
30.4
23.9–27.4
NTVXXXXM-R
500
60
24.4
30.4
23.9–27.4
23SXXX
2000
50
12.4
18.4
11.9–15.4
24XXX
1500
50
12.4
18.4
11.9–15.4
24SXXX
1000
50
16.4
22.4
15.9–19.4
26XXX
500
60
24.4
30.4
23.9–27.4
26SXXX
500
60
24.4
30.4
23.9–27.4
6001
500
60
24.4
30.4
23.9–27.4
78XXXM/MV
500
60
24.4
30.4
23.9–27.4
78253/XXM
500
60
24.4
30.4
23.9–27.4
78253/XXMV
500
60
24.4
30.4
23.9–27.4
786XX/XM
500
60
24.4
30.4
23.9–27.4
No.
1
CARRIER TAPE OUTLINE DIMENSIONS
Order Code
Reel Outline Dimensions
A1
9.40
-
B0
E2
Figure
F
K0
K1
13.20 22.25
11.50
6.80
-
12.00 24.00
2
NTAXXXXM-R
11.50 6.70 15.79 22.25
11.50
7.25 6.55 16.00 24.00
3
NTEXXXXM-R
11.50 6.70 13.25 22.25
11.50
7.25 6.55 16.00 24.00
3
NTVXXXXM-R
11.50 6.70 15.79 22.25
11.50
7.25 6.55 16.00 24.00
3
DA10XM
A0
P1
W
No.
■ The carrier tape shall be released
from the reel hub as the last portion
of the carrier tape unwinds from the
reel.
23SXXX
6.20
-
6.80 10.25 5.50±0.05
3.60
-
8.00 12.00
4
24XXX
5.60
-
6.20 10.25 5.50±0.05
4.70
-
8.00 12.00
4
■ Sprocket hole pitch over any 10
pitches ±0.2mm.
24SXXX
7.40
-
8.20 14.25
7.50
6.00
-
12.00 16.00
5
26XXX
9.60
-
10.50 22.25
11.50
5.70
-
12.00 24.00
4
26SXXX
12.10
-
13.10 22.25
11.50
6.90
-
16.00 24.00
5
6001
12.60
-
12.60 22.25
11.50
8.20 7.30 16.00 24.00
6
78XXXM/MV
9.40
-
13.20 22.25
11.50
6.80
-
12.00 24.00
2
78253/XXM
9.40
-
13.20 22.25
11.50
6.80
-
12.00 24.00
2
78253/XXMV
9.40
-
13.20 22.25
11.50
6.80
-
12.00 24.00
2
786XX/XM
9.40
-
13.20 22.25
11.50
6.80
-
12.00 24.00
2
■ Carrier tape camber shall not exceed
1mm/250mm in either direction.
www.dc-dc.com
TAPE & REEL
Specifications
1 - REEL OUTLINE DIMENSIONS
All dimensions in mm.
1 - Includes flange distortion at
outer edge.
2 - Measured at hub.
2 - CARRIER TAPE
Unless otherwise stated all dimensions in mm ±0.10mm.
Components shall be orientated within the carrier tape pocket as indicated.
1 - Measured on a plane 0.3mm above the bottom of the pocket.
TAPE & REEL
Specifications
3 - CARRIER TAPE
Unless otherwise stated all dimensions in mm ±0.10mm.
Components shall be orientated within the carrier tape pocket as indicated.
4 - CARRIER TAPE
Unless otherwise stated all dimensions in mm ±0.10mm.
1 - Components shall be orientated within the carrier tape pocket as indicated with exception of 23SXXX series.
2 - 23SXXX series components shall be orientated within the carrier tape pocket as indicated.
3 - Measured on a plane 0.3mm above the bottom of the pocket.
TAPE & REEL
Specifications
5 - CARRIER TAPE
Unless otherwise stated all dimensions in mm ±0.10mm.
Components shall be orientated within the carrier tape pocket as indicated.
1 - Measured on a plane 0.3mm above the bottom of the pocket.
6 - CARRIER TAPE
Unless otherwise stated all dimensions in mm ±0.10mm.
Components shall be orientated within the carrier tape pocket as indicated.
1 - Measured on a plane 0.3mm above the bottom of the pocket.
C&D Technologies (NCL) Limited reserve the right to alter or improve the
specification, internal design or manufacturing process at any time, without
notice. Please check with your supplier or visit our web site to ensure that
you have the current and complete specification for your product before use.
© C&D Technologies (NCL) Limited 2000
NDC AN002.1
No part of this publication may be copied, transmitted or stored in a
retrieval system or reproduced in any way including, but not limited to,
photography, photocopy, magnetic or other recording means, without prior
written permission from C&D Technologies (NCL) Limited.
Instructions for use are available from www.dc-dc.com
C&D Technologies (NCL) Ltd
Tanners Drive, Blakelands North
Milton Keynes MK14 5BU, England
Tel: +44 (0)1908 615232
Fax:+44 (0)1908 617545
email: [email protected]
www: http://www.dc-dc.com
C&D Technologies (NCL), Inc.
8917 Glenwood Avenue, Raleigh
NC 27612, USA
Tel: +1 (919) 571-9405
Fax: +1 (919) 571-9262
email: [email protected]