Download

Products Related to Common Sockets and DIN Tracks
CSM_common_sockets_DS_E_3_3
A Wide Variety of Square and
Round Sockets in Front-mounting
and Back-mounting Models
• Models available with finger protection.
• Hold-down Clips and Socket Bridges for PYF Sockets
are also available.
• New screwless models available.
Models Used with Common Sockets
Sockets
Item
Model
Group name
Proximity Sen- E2C
sors
Number of
pins
8 P2CF-08
E2C-AK4A
11 P2CF-11
E2C-GE4A
E2C-GF4A
8 PYF08A
61F-GP-N8
61F-APN2
PF083A
8
61F-HSL
Level
Devices
61F
K7L
61F-IP
61F-G1P, -G2P
14 14PFA
MY1, MY2
MY
(Q, K, H) MY4, MYQ4
MY4Z-CBG
MY2K, MY4H
G2A(K)
LY1, LY2
LY3
LY4
G7K-412S
G2A,
G2A-434
G2AK
MK2P
MK(K)
MK3P
MK2KP
MM2(X)P
P3G
MM3P
MM2(X)KP
P3GA
MM
PY
PL
8 P2RF-08(-E)
---
Generalpurpose
Relays and
Solid-state
Relays
8
11
PYF
PY
14
8
11
PTF
14
14 PYF
---
G3F
G3F(D) Series
G3FM
G3H
G3H(D) Series
G3B
G3B(D) Series
G9H
G9H-2@@S
Number
of pins
Applicable Sockets
Frontmounting
8 8PFA
11
PFA
PL
14
8 8PFA1
PL
PYF
PY
8 PTF
PF083A
PT
PTF
PT
PL
5 P2RF-05@
P2R
-05@
G2R-2-S@
8 P2RF-08@
P2R
-08@
G3R
---
5 P2RF-05@
P2R
-05@
G7T
G3TA
G7T
G3TA
5 P7TF-05
---
G7S
G7S-4A2B-E
G7S-3A3B-E
14 P7S-14F-END
P7S
-14P-E
G7SA-3A1B
G7SA-2A2B
10
P7SA-10F
P7SA-10F-ND
P7SA
@-10P
G7SA-5A1B
G7SA-4A2B
G7SA-3A3B
14
P7SA-14F
P7SA-14F-ND
P7SA
@-14P
H3CA-8(H)
8
G2R
PY
P3G
PL
H3CA
PL
Timers
Backmounting
G2R-1-S@
G7SA
---
MM3XP
MM3(X)KP
MM4(X)P
MM4(X)KP
G4Q
PT
8 PF083A(-E)
11 PF113A(-E)
Model
Group name
8PFA
11 PF113A
K7L-AT50/AT50D
K7L-U/-UD
Backmounting
8PFA1
61F-03B, -04B
61F-GP-N
61F-GPN-V50
61F-GPN-BT/BC
MY3
Generalpurpose
LY
Relays
and Solidstate Re- G7K
lays
Front-mounting
E2C-AM4A
61F-UHS
Item
Applicable Sockets
H5CN
H5CX
H5CZ
H3CA-A
11
H5CN-@M
11
Other H5CN
models
H5CX-L8@
H5CX-A11@
H5CZ-L8@
P3GA
PL
P2CF
P3GA
8
P3G
8
P3G
11
8
P3GA
P3G
1
Products Related to Common Sockets and DIN Tracks
Item
Model
Group name
H3CR-A8@
H3CR-F8@
H3CR-G8@
H3CR-H8@
H3CR
H3M
H3CR-A
H3CR-AS
H3CR-AP
H3CR-F
H3CR-FN
H3CR-HRL
Number of
pins
Applicable Sockets
Front-mounting
P3G
PL
8
P2CF
P3GA
PL
11
---
8 PF085A
H3Y-2
8
H3Y-4
14
8
H3YN-4@
14
H3RN-1@
5
H3RN-2@
8
RD2P
---
8 8PFA1
H2C
---
8
H3RN
H7CX
H7CX-A11@
H7CZ
H7CZ-L8@
8
H7CN-@M
11
Counters
H7CN
E5CN
TemE5C2
perature
Control- E5CS
lers
E5L
Signal
Converters
Component
Protective
Components
Products for
Highvoltage
Power
Receiving
Equipment
Annunciators
PYF
H3YN-2@
H3YN
Other H7CN
models
E5CN-@U
--E5CS-@1, @2
Other E5CS
models
--K3FK models not
listed below
K3FK
K3FK-G@
K3FK-GS@
K3FK-SL-?5-@
SE
SE-KP@N
SAO
SAO-@
APR
K2CU
SDV
APR-S
APR-S380/-S440
K2CU-P
SDV-F@@/-FH@T
SDV-D@@
P2RF-@-E
P2CF
PF085A
11
P2R
@-@7P
For Square Sockets
Sockets
PYF08M
P3G
PL
PY@(QN)
PT@(QN)
PYC
PYC-P
PYC-P
PYC-S
MY@I *
LY@I
---
PYC-P2
MY4H
---
PYC-P
PY@-02
PT@-0
PYC-P
PYC-A1
MY2Z@-CR
MY3@-CR
LY@-CR
Y92H-3
---
PYC-1
G2A(K) Series
PYC-A2
---
PYC-2
PYC-3
PYC-5
G7K
PKC
---
H3Y
Y92H-3
---
PYC-3
PYC-5
Y92H-4
Note: The @ in the model number is replaced with 08, 11, or 14.
* If you use a Hold-down Clip with the MY2I, you cannot use the
PYF08A.
Use the PYF14A.
P3G
P2CF
8
P3GA
For Round Sockets
Sockets
P3G
11
P3GA
8
P3G
14 PTF14A
---
8PFA (Included
8
with Converter)
11PFA
11 (Included with
Converter)
8
MY@, MY@N,
MY@-D, MY2@-CR,
MY4@-CR,
MY4Z@-CR,
MY@-TU, MY2K,
MY@N-D2, LY@,
LY@N, LY@-TU,
MYQ@,
G3H(D) Series,
G3F(D) Series,
G3FM, and G9H
PYF@A
PTF@A
PL
P3G
---
Applicable models
PF083A
PF113A
PL08 (-Q)
PL11 (-Q)
61F-03B, -04B
PFC-A1
PLC
61F-GP-N,
-GPN-BT
61F-GP-N8
?61F-APN2
PFC-N8
PHC-5
MK2P Series,
MK2KP,
MK3P@(-US), and
G3B(D) Series
PLE08-0
PLE11-0
P2CF-11
PLC-10
---
PLC
PFC-A1
8PFA1
---
MK3ZP
MK3LP
PF083A
PL08
PFC-A6
PLC-7
---
---
---
MYA-NA1, -NB1
MYA-LA1, -LB1
MYA-NA2, -NB2
MYA-LA2, -LB2
PL08
MYA-LA12, -LB12
PFC-A7
PLC-8
---
---
PL15
APR-S
PFC-A6
PLC-7
---
---
PL08
APR-S380/-S440
---
---
---
Y92H-1
PL11 and
P3GA-11
LG2
PFC-A7
PLC-8
---
---
K6EL
---
Y92H-1
---
---
11 P2CF-11
8 8PFA1
14 14PFA
LG2-@
8 PF083A
K6EL
K6EL-@
11 P2CF-11
MYA
PY
P3GA
8
11
P3G
PL
P3GA
LG2
AGF
Hold-down Clips
Applicable models
Timers
H3Y
Backmounting
AGF-1-P5
8 8PFA1
MYA-NA1, -NB1
8 PF083A
MYA-NA2, -NB2
MYA-LA1, -LB1
MYA-LA2, -LB2
MYA-LA12, -LB12
11 PF113A
PL11
---
PLC-1
Note: 1. The 8PFA(1), 11PFA, and 14PFA are held with hooks.
2. The PL15, PL20, and PF202, as well as models not given in
the above table, require panel processing for installation.
3. The PF085A Hold-down Clip is included with the H3M and
H2A. It is an option (sold separately) for the H2C.
PL
2
Products Related to Common Sockets and DIN Tracks
Ordering Information
Square Sockets
Model
P2R (back-mounting), pages 11 and 12
P2RF (front-mounting), page 9
Number of pins
Solder terminals
P7TF (frontmounting), page 12
PCB terminals
P2RF-05
Approx. 27 g
P2RF-05-E*
Approx. 38 g
P2RF-05-S
Approx. 36 g
P2R-05A
Approx. 5 g
P2R-05P
Approx. 5 g
P2R-057P
Approx. 5.5 g
P2RF-08
Approx. 33 g
P2RF-08-E*
Approx. 38 g
P2RF-08-S
Approx. 40 g
P2R-08A
Approx. 5 g
P2R-08P
Approx. 5 g
P2R-087P
Approx. 5.5 g
P7TF-05
Approx. 28 g
5 pins
---
8 pins
Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
2. To remove the Relay, pull the lever on the Socket with your fingers supporting the lever and the opposite side of the Relay case, and
jiggle the Relay.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.
Minimum Order Lot The following models are available at the minimum order lot specified below.
Number of pins
Model
P2RF
P2R
P7TF
5 pins
P2RF-05
P2R-05A
P2R-05P
P7TF-05
8 pins
P2RF-08
P2R-08A
P2R-08P
---
Model
Number
of pins
8 pins
Minimum order lot (pcs)
10
PY (back-mounting), page 15
PYF (front-mounting), page 14
Solder terminals
PYF08A
Approx. 32 g
PYF08M
Approx. 26 g
PYF08A-E *1
PYF08S
Approx. 46 g
PY08
Approx. 8 g
Wrapping terminals
PY08-Y1
PY08-Y3
PY08QN
Approx. 12 g
PY08QN2
PY11
Approx. 9 g
PY11-Y1
PY11QN
PY11QN2
PY11QN-Y1
PY11QN2-Y1
PY14
Approx. 10 g
PY14-Y1
PY14-Y3
PY14QN
Approx. 14 g
PY14QN2
PY14QN-Y1
PY14QN2-Y1
PY14QN-Y3
PY14QN2-Y3
1
PYF11A
Approx. 43 g
PCB terminals
PY08-02 *2
Approx. 7.2 g
PY08QN-Y1
PY08QN2-Y1
?
PY11-02 *2
11 pins
PYF14A
Approx. 49 g
14 pins PYF14A-E*1
PYF14T
Approx. 53 g
PY14-02 *2
PYF14S
Approx. 62 g
3
Products Related to Common Sockets and DIN Tracks
Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
2. Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.
*1. Use a #1 Phillips screwdriver to tighten the screws on this Socket.
*2. The structure does not resist flux. Manual soldering is recommended for this product.
Model
PT (back-mounting), page 18
PTF (front-mounting), page 17
Number
of pins
Solder terminals
PTF08A-E *1
PTF08A Approx. 47 g
Wrapping terminals
PCB terminals
PT08 Approx. 11 g
PT08QN
Approx. 10.4 g
PT08-0 *2
Approx. 8 g
PT11 Approx. 13 g
PT11QN
PT11-0 *2
Approx. 12.2 g
PT14 Approx. 17 g
PT14QN
Approx.
20 g
PT14-0 *2
Approx. 16.2 g
8 pins
PTF11A Approx. 61 g
11 pins
PTF14A-E *1
PTF14A Approx. 77 g
14 pins
Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.
* The structure does not resist flux. Manual soldering is recommended for this product.
Minimum Order Lot
Number of pins
Model
The following models are available at the minimum order lot specified below.
PYF
PY
PTF
PT
8 pins
PYF08A
PYF08M
PY08
PTF08A
PT08
11 pins
PYF11A
PY11
PTF11A
PT11
14 pins
PYF14A
PY14
PTF14A
PT14
Model
Number
of pins
Model
10
P7S/P7SA, pages 20 and 21
P7LF (front-mounting), page 20
P7LF-06 Approx. 60 g
6 pins
Minimum order lot (pcs)
Number
of pins
Front-mounting
PCB terminals
P7SA-10F Approx. 44 g
P7SA-10F-ND Approx. 44 g
P7SA-10P Approx. 9 g
P7S-14F-END Approx. 110 g
P7S-14P-E Approx. 25 g
P7SA-14F Approx. 59 g
P7SA-14F-ND Approx. 59 g
P7SA-14P Approx. 10 g
10 pins
14 pins
Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.
4
Products Related to Common Sockets and DIN Tracks
Round Sockets
Model
PF (front-mounting),
page 22
Number
of pins
P2CF (front-mounting),
page 23
PF083A
Approx. 34 g
P2CF-08
Approx. 55 g
PFA (front-mounting),
page 24
8PFA
Approx.
57 g
PL (back-mounting), page 26
P3G (back-mounting),
page 25
Solder
terminals
P3G-08
Approx. 40g
Wrapping
terminals
PCB
terminals
PL08
Approx. 14 g
PL08-Q
PLE08-0
Approx. 15 g Approx.
10.6g
PL11
Approx. 15 g
PL11-Q
Approx.
18.5A
PF083A-E *
P2CF-08-E
8PFA1
Approx.
66 g
8 pins
Note: The Y92A-48G
Terminal Cover
can be used to
provide finger
protection.
PF085A
Approx. 40 g
PF113A
Approx.
47 g
P2CF-11
Approx.
70g
PF113A-E *
P2CF-11-E
11PFA
Approx. 74 g
P3GA-11
Approx.
47 g
PLE11-0
Approx.
10.8 g
11 pins
Note: The Y92A-48G
Terminal Cover
can be used to
provide finger
protection.
14PFA Approx. 104 g
14 pins
---
PL15
Approx. 28 g
---
---
---
---
---
---
PL20
Approx. 17 g
20 pins
---
---
---
---
Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.
Minimum Order Lot
Number of
pins
The following models are available at the minimum order lot specified below.
PF
Model
P2CF
PFA
P3G
PL
8 pins
PF083A, PF085A
P2CF-08, P2CF-08-E
8PFA. 8PFA1
P3G-08
PL08
11 pins
PF113A
P2CF-11, P2CF-11-E
11PFA
P3GA-11
PL11
14 pins
---
---
Minimum order lot
(pcs)
20
10
14PFA
--20
PL15
10
Terminal Cover
Model
Y92A-48G
Appearance
Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.
5
Products Related to Common Sockets and DIN Tracks
Hold-down Clips
(Unit: mm)
For Square Sockets
PHC-12
PKC One Set (2 Clips)
PYC-A1 Approx. 0.54 g
One Set (2 Clips)
PTC-1
5
4.5
PYC-E1
One Set (2 Clips)
PYC-A2
One Set (2 Clips)
3
29
7°
71.8
2.7
3
4.5
PYC-P Approx. 1.4 g
36.3
36.3 40.7
4.5
1
9.6
PYC-P2 Approx. 1.2 g
PYC-S Approx. 1.8 g
4.5
4.5
1.2
4.5
PYC-1 Approx. 6 g
8
28
5.8
4.3
1.2
PYC-3
PYC-2
8
28
5
Approx. 3
28.8
28
Approx. 3
±0.1
4.5
1.2
9.4
10
5
29 max.
42.8
36.3
Approx. 16
2.5
5 max.
10
Approx.
30.5
2.7
5 max.
5 max.
3.3
29.5
2.5
52 58.2
38.5
PYC-5
PYC Approx. 0.2 g
Y92H-1
Y92H-3
One Set (2 Clips)
10
10
3
6
44.5
Y92H-4
R9
5 max.
5
30.5
3.5
24.5
2.5
3.7
3.7
53
20
72.9
1.5
34.5
(84°)
1.5
34.7
23.5
41.7
33.7
6
6
2
10
4.5
1.2
4.5
For Round Sockets
PFC-A1 Approx. 2.2 g
One Set (2 Clips)
PFC-A6 Approx. 2.4 g
One Set (2 Clips)
73.3
62
PLC Approx. 2.4 g
One Set (2 Clips)
94
74.5
4.5
56.6
69.2 65.7
56.3
8
8
4.5
6
9
6
PLC-8 Approx. 6.4 g
One Set (2 Clips)
PLC-10 Approx. 2.0 g
One Set (2 Clips)
4.5
PLC-12 Approx. 5.4 g
One Set (2 Clips)
Minimum Order Lot
The following models are available at the
minimum order lot specified below.
5
Type
90.2 86.7
66.2
Model
64.3
8
8
9
PLC-7 Approx. 3.0 g
One Set (2 Clips)
95.2
7.6
6
PLC-1 Approx. 2.6 g
One Set (2 Clips)
4.6
4.6
4.6
60.8
PFC-A7 Approx. 3.0 g
One Set (2 Clips)
For Square
Sockets
6
For Round
Sockets
Minimum
order lot
(pcs)
PYC-A1
PYC-P
100
PYC-A2
PYC-S
PYC-1
PYC-2
PYC-3
PYC-5
10
PFC-A1
PFC-A6
PFC-A7
PLC
20
6
Products Related to Common Sockets and DIN Tracks
Specifications
Socket Characteristics
Model
Continuous
carry current
P2RF-05(-E)(-S)
10 A
P2RF-08(-E)(-S)
5A
Dielectric strength
Between contact terminals of same polarity: 1,000 VAC for 1 min
Between coil and contact terminals: 4,000 VAC for 1 min
Insulation
resistance*1
Remarks
1,000 MΩ min.
Between contact terminals of different polarity: 3,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
P2R-05P
10 A
P2R-08P
5A
Between contact terminals of same polarity: 1,000 VAC for 1 min
Between coil and contact terminals: 4,000 VAC for 1 min
1,000 MΩ min.
Between contact terminals of different polarity: 3,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
P2R-057P
10 A
P2R-087P
5A
Between contact terminals of same polarity: 1,000 VAC for 1 min
Between coil and contact terminals: 5,000 VAC for 1 min
1,000 MΩ min.
Between contact terminals of different polarity: 3,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 5,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2R-05A
10 A
Between ground terminals: 1,500 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of different polarity: 3,000 VAC for 1 min
P2R-08A
5A
P7TF-05
5A
Between contact terminals of same polarity: 1,000 VAC for 1 min
Between ground terminals: 1,500 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
PYF08A(-E)(-S)
PYF11A
PYF14A(-E)(-S)
Between terminals: 2,000 VAC for 1 min
100 MΩ min.
7 A, -S models:
10 A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
5A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
3 A, -S models:
5A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
1,000 MΩ min.
PY08(-Y1)
7A
Between terminals: 1,500 VAC for 1 min
PY08QN(-Y1)
7A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY08-02
7A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY11(-Y1)
5A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY11QN(-Y1)
5A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY11-02
5A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY14(-Y1)
3A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY14QN(-Y1)
3A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PY14-02
3A
Between terminals: 1,500 VAC for 1 min
100 MΩ min.
PTF@@A(-E)
10 A
Between terminals: 2,000 VAC for 1 min
100 MΩ min.
PT@@
10 A
Between terminals: 2,000 VAC for 1 min
100 MΩ min.
PT@@QN
10 A
Between terminals: 2,000 VAC for 1 min
100 MΩ min.
PT@@-0
10 A
Between terminals: 2,000 VAC for 1 min
100 MΩ min.
The continuous carry current of 10
A for the PYF08S is for an
ambient temperature of 55°C.
At an ambient temperature of
70°C, the value is 7 A.
Between contact terminals of different polarity: 2,000 VAC for 1 min
P7LF-06
30 A
Between contact terminals of same polarity: 2,000 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
PF@@@A
5A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
P2CF
5A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
P3G(A)
6A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
8PFA(1)
10 A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
11PFA(1)
10 A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
PL@(-Q)
10 A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
PLE@@-0
10 A
Between terminals: 2,000 VAC for 1 min
1,000 MΩ min.
P6D-04P
5A
P7S-14@-E(ND)
10 A
Between contact terminals of same polarity: 1,000 VAC for 1 min
Between coil and contact terminals: 3,000 VAC for 1 min
100 MΩ min.
Between contact terminals of different polarity: 2,000 VAC for 1 min
Between contact terminals of same polarity: 1,500 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 2,000 VAC for 1 min
7
Products Related to Common Sockets and DIN Tracks
Model
Continuous
carry current
Dielectric strength
Insulation
resistance*1
Remarks
Between contact terminals of different polarity: 2,500 VAC for 1 min
P7SA-10@
6 A *2
Between contact terminals of same polarity: 1,500 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 2,500 VAC for 1 min
Between contact terminals of different polarity: 2,500 VAC for 1 min
P7SA-14@
6 A *2
Between contact terminals of same polarity: 1,500 VAC for 1 min
1,000 MΩ min.
Between coil and contact terminals: 2,500 VAC for 1 min
*1. The insulation resistance was measured with a 500-VDC insulation resistance meter at the same places as those used for measuring the
dielectric strength.
*2. There are restrictions in the current. Refer to the General Catalog for the OMRON Safety Components (Cat. No. Y106) for details.
Safety Precautions
Refer to Common Relay Precautions for general precautions.
8
Products Related to Common Sockets and DIN Tracks
Dimensions
P2RF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
P2RF-05
(One Pole)
7±0.2
Mounting Hole Dimensions
2
5-M3.5×8
4.2-dia. hole
4 dia.
9.5
4
35.5
71.5 max.
30±0.05
3
4
4
5
19.5
30 max.
19.5 max.
M3 (M3 x 16)
or 3.2-dia. hole
(Top View)
54 max.
(Top View)
P2RF-05-E (One Pole)
(Finger Protection Structure)
5-M3.5×7
2
1
Note: Track mounting is also possible.
Refer to page 27.
7±0.2
59 max.
(80.9 max.)*
48 max.
2
3.2-dia. hole
4
(11)
(12)
2
3
(14)
7
39.5±0.1
3.5-dia. hole
4
39.5
5
85.5 max.
35.5
(A1)
(A2)
1
M3 or 3.5-dia. hole
(Top View)
16
4
61 max.
*When mounted
on H3RN-1@.
11.5
(Top View)
Note: Figures in parentheses
indicate DIN standard
numbers.
Note: Track mounting is also possible.
Refer to page 27.
P2RF-05-S (One Pole)
(Screwless Model)
4
(11)
32.6
3
27.6
18.0 max.
(14)
22.6
2
(12)
24.5
--35.3
91.8 max.
(A1) (A2)
5
(Top View)
Note: Figures in parentheses
indicate DIN standard
numbers.
(5.3)
28.5
(2.4)
32.6
P2RF-08
(Two Poles)
1
2
7±0.2
8-M3.5×8
4.2-dia. hole
4 dia.
35.5
71.5 max.
9.5
6
3
5
4
30±0.05
4
M3 (M3 x 16)
or 3.2-dia. hole
4
19.5 max.
19.5
30 max.
7
8
2
1
(Top View)
54 max.
(Top View)
Note: Track mounting is also possible.
Refer to page 27.
9
Products Related to Common Sockets and DIN Tracks
P2RF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
P2RF-08-E
(Two Poles)
(Finger Protection Structure)
1.5
2
8-M3×8
6+0.2
−0.1
(21)
(22)
63 max.
(84.9 max.)*
48 max.
2
Mounting Hole Dimensions
(11)
6 3
(12)
7 2
5 4
3.2-dia. hole
7
(24) (14)
3 dia.
39.5±0.1
3.5-dia. hole
8
39.5
35.5
85.5 max.
16
4
61 max.
*
When mounted
11.5 on H3RN-2@.
(A1)
4
1
(Top View)
Note: Figures in
parentheses
indicate DIN
standard numbers.
6
P2RF-08-S (Two Poles)
(Screwless Model)
M3 or 3.5-dia. hole
(Top View)
Note: Track mounting is also possible.
Refer to page 27.
3
(21) (11)
5
27.6
22.6
4
(24) (14)
32.6
18.0 max.
(A2)
7
(3.4)
2
(22) (12)
24.5
--35.3
91.8 max.
(A1) (A2)
8
1
(Top View)
(2.4)
28.6
32.6
(5.3)
Note: Figures in
parentheses
indicate DIN
standard numbers.
Note: 1. If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.
2. Refer to pages 28 and 30 for the features of Screwless Sockets and for precautions for correct use.
10
Products Related to Common Sockets and DIN Tracks
P2R
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
PCB Dimensions
P2R-05P (One Pole)
4
14.5 max.
7.5 3.5
1
35.5 max.
3
6
4.5
15
3.5
1.2
6
4.5
4
2
Five, 1.6-dia. holes
15
4
1
1.5
4
5
(5)
7
4 7
(Bottom View)
36.5 max.
(Bottom View)
P2R-08P (Two Poles)
7.5
7.5 3.5
14.5 max.
0.3
5
5
35.5 max.
1
2.8
4
3
2
5
6
7
1
8
Eight, 1.3-dia holes
5
5
20
20
1.5
(4.3)
7.5
(Bottom View)
36.5 max.
(Bottom View)
P2R-057P (One Pole)
14 max.
0.7
8.7
1
4±0.1
16.4
10.4 3.5
Five, 1.6-dia. holes
1
6
4.5
15
3
4
8.75
2
29.6
37 max.
1
8.7
6±0.1
4
4.5±0.1
15±0.1
4±0.1
(8.75)
1
7.4
5
7±0.1
4 7
(Bottom View)
41 max.
(Bottom View)
P2R-087P (Two Poles)
14 max.
7.5
1
16.4
10.4 3.5
7.5
0.3
4
3
2
5
5
37 max. 29.1
20
1
5
6
7
Eight, 1.3-dia holes
5
5
8.1
8.9
20
7.4
1
8
(8.1)
7.5
41 max.
(Bottom View)
(Bottom View)
Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.
11
Products Related to Common Sockets and DIN Tracks
P2R
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
Mounting Hole Dimensions
P2R-05A (One Pole)
7.5 4.5
14.5 max.
1.2
3
4
2
0.3
6.7
35.5 max.
5
16.7
3.8
1
5
Five, 3 x 1.8-dia. holes
13.6±0.1
6
(Bottom View)
36.5 max.
30.5+00.2
P2R-08A (Two Poles)
7.5
6.5
14.5 max.
1.2
0.3
5
5
35.5 max.
2.6
2.8
4
3
2
5
6
7
1
8
(Use panel with thickness of
1.6 to 2.0 mm.)
20
1.5
Eight, 3 x 1.2-dia. holes
7.5
(Bottom View)
36.5 max.
Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.
P7TF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
Mounting Hole Dimensions
12.5±0.2
P7TF-05
M3 or M4*
19 max.
7+0.2
-0
5-M3.5×8
4
3
62±0.1
2
35.5
71.5 max.
1
M3
5
(Top View)
4
9
12.5±0.2
19.5
59 max.
(Top View)
Note: Track mounting is also possible.
Refer to page 27.
* We recommend that you use washers
if you use M3 bolts or screws.
Washers are not required with M4
bolts or screws.
Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is positive.
12
Products Related to Common Sockets and DIN Tracks
PYF
(Unit: mm)
Terminal
Arrangement/Internal
Connections
Dimensions
PYF08A
Mounting Hole Dimensions
PYF08A-E
(Finger Protection Structure)
6+0.2
−0.1
Two, 4.2 × 5
mounting holes
6+0.2
−0.1
Two, 4.2 × 5
mounting holes
3.4
8-M3×8
8-M3×8
Two M3 or M4
or 4.5-dia. holes
3.4
4 1
5
8
35.4
72 max.
72 max.
59±0.3
35.4
12
9
14 13
4
4
23 max.
(Top View)
4
6
Note: Track mounting is also
possible.
Refer to page 27.
6
23 max.
16.5
15±0.2
(Top View)
16.5
30 max.
31 max.
PYF08M
8-M3.5×7.5
3 dia.
7±0.2
33.5 max.
4
8
12
1
5
9
14
13
3.5-dia. hole
20±0.1
1.5
44.5 max.
3.5-dia. mounting holes
6.5-dia. countersinking, depth: 11.5
PYF08S
(Screwless Model)
18 max.
3.5-dia. or M3 hole
(Top View)
38.2 max.
36.5 max.
32.6
27.6
22.6
23.2 max.
12
9
(41)
(11)
8
5
(44)
(14)
4
1
(42)
(3.4)
(12)
---
24.5
(A2)
85 max.
35.4
14
(A1)
13
(Top View)
28.6
(5)
(5.3)
32.6
PYF11A
Two, 4.2 × 5
mounting holes
6+0.2
−0.1
Note: Figures in
parentheses
indicate DIN
standard
numbers.
Two M3 or M4
or 4.5-dia. holes
3.4
11-M3×8
3 2 1
6
5 4
9
8 7
11 10
59±0.3
35.4
72 max.
4
29.5 max.
6
16.5
30 max.
(Top View)
22±0.2
(Top View)
Note: Track mounting is also
possible.
Refer to page 27.
13
Products Related to Common Sockets and DIN Tracks
PYF
(Unit: mm)
Terminal
Arrangement/Internal
Connections
Dimensions
PYF14A
Two, 4.2 × 5
mounting holes
Mounting Hole Dimensions
PYF14A-E
(Finger Protection Structure)
6+0.2
−0.1
Two, 4.2-dia × 5
6+0.2
−0.1
mounting holes
3.4
14-M3×8
Two M3 or M4
or 4.5-dia. holes
3.4
14-M3×8
59±0.3
35.4
72 max.
35.4
72 max.
22±0.2
(Top View)
4
29.5 max.
3 2 1
4
4
6
6
29.5 max.
16.5
30 max.
8 7 6 5
16.5
31 max.
PYF14T
Two, 4.2-dia × 5
mounting holes
12 11 10 9
4 14 13
30
23.5
11.5
11
33 max.
7±0.2
Note: Track mounting is also
possible.
Refer to page 27.
2-M4
(Top View)
59
35.5
70 max.
24.5
(Top View)
17.8
4
Note: Track mounting is also
possible.
Refer to page 27.
14-M3.5×8
17.4
PYF14S
(Screwless Model)
10
36.5 max.
12 11 10 9
(41) (31) (21) (11)
8
7
6
5
(44) (34) (24) (14)
32.6
27.6
31 max.
22.6
4
3
2
1
(42) (32) (22) (12)
(3.4)
---
24.55
85 max.
35.4
(A2)
14
(A1)
13
(Top View)
(4.15)
28.6
32.6
Note: Figures in
parentheses
indicate DIN
standard
numbers.
Note: Refer to pages 28 and 30 for the features of Screwless Sockets and for precautions for correct use.
14
Products Related to Common Sockets and DIN Tracks
Relay Sockets and Socket Bridges for PYF
Bridges within the Same Socket
Pitch
Applicabl
e models
Appearance
Dimensions (mm)
Model
Specifications
7
PYD-020B@(2P)
3.2
7
mm
5.6
PYF14A
7
7
PYD-030B@(3P)
Max. carry current: 20 A (18 A at 70°C)
Ambient operating temperature: -40 to 70°C (with no
icing or condensation)
Ambient operating humidity: 45% to 85% (with no
icing or condensation)
Conductor material: Brass
Conductor surface treatment: Nickel plating
Package qty: 50/bag
3.2
5.6
Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, Y: Yellow
2. Specify the number of bags when ordering.
Bridges between Adjacent Sockets
Pitch
Applicabl
e models
Appearance
Dimensions (mm)
Model
40°
22
PYD-025B@(2P)
22
mm
Specifications
3.3
5.6
PYF08A
154
40°
22
PYD-085B@(8P)
Max. carry current: 20 A (18 A at 70°C)
Ambient operating temperature: -40 to 70°C (with no
icing or condensation)
Ambient operating humidity: 45% to 85% (with no
icing or condensation)
Conductor material: Brass
Conductor surface treatment: Nickel plating
Package qty: 10/bag
3.3
5.6
40°
29
PYD-026B@(2P)
29
mm
3.3
5.6
PYF14A
203
40°
29
PYD-086B@(8P)
Max. carry current: 20 A (18 A at 70°C)
Ambient operating temperature: -40 to 70°C (with no
icing or condensation)
Ambient operating humidity: 45% to 85% (with no
icing or condensation)
Conductor material: Brass
Conductor surface treatment: Nickel plating
Package qty: 10/bag
3.3
5.6
Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, S: Blue, R: Red
2. Specify the number of bags when ordering.
Socket Bridges
Pitch
Applicable models
Appearance and dimensions (mm)
19.7
PYF08S
mm
Insulating coating
27.5
PYF14S
mm
14.3
P2RF-@@-S
mm
9
Guide: 1.2 dia.
Pitch
14
Model
Insulation color
PYDM-08SR
Red
PYDM-08SB
Blue
PYDM-14SR
Red
PYDM-14SB
Blue
P2RM-SR
Red
P2RM-SB
Blue
Note: 1. Use the Socket Bridges for relay coil bridge wiring.
2. Specify the number of bags when ordering.
Safety Precautions
Maximum Carry Current
• The total current of all bridged poles must not exceed the maximum carry current of the Socket Bridge.
• Make sure that the maximum carry current of the relay contacts is also not exceeded for each pole.
• If you use more than one Socket, use End Plates (PFP-M).
15
Products Related to Common Sockets and DIN Tracks
PY
(Unit: mm)
Terminal
Arrangement/
Internal
Connections
Dimensions
PY08
PY08-Y1 (L = 42 max.)
PY08-Y13 (L = 60 max.)
*
Mounting hole and PCB dimensions
Eight, 3 x 1.2 ellipses
25.5 max.
29.5 max.
5
2.7
*The
PY08-Y@ includes
the part outlined by the
dashed lines above.
24 max.
20 max.
L
25.8±0.2
2.6
7.7
21.4+0.2
0
PY08QN
PY08QN2
PY08QN-Y1
PY08QN2-Y1
1
*1
29.5 max.
5
*2
*1. The PY08QN(2)-Y1 includes the part
2.7
outlined by the dashed lines above.
*2. The figures in the parentheses are for
42 max.
(20)
25
41.5 max.
(36.5 max.)*2
22 max.
24 max.
the PY08QN2(-Y1).
1
4
5
8
9
12
13
14
(Bottom View)
13.2
5.8
4.1
1.0
PY08-02
* The structure does not resist flux. Manual
soldering is recommended for this product.
6.35
0.3
6.4
25.5 max.
29.5 max.
4.2
2.7
4.3
22 max.
12.65
Eight, 1.3-dia holes
2
16.5 max.
*
PY11
PY11-Y1
Eleven, 3 x 1.2 ellipses
25.5 max.
29.5 max.
5
*The
PY11-Y1 includes the
part outlined by the dashed
lines above.
PY11QN
PY11QN2
PY11QN-Y1
PY11QN2-Y1
42 max.
2.6
7.7
2.7
25.8±0.2
24 max.
20 max.
21.46+0.2
0
1
*1
29.5 max.
5
2.7
*1. The PY11QN(2)-Y1 includes the part
outlined by the dashed lines above.
*2. The figures in the parentheses are for
the PY11QN2(-Y1).
42 max.
(20)*2
25
41.5 max.
(36.5 max.)*2
22 max.
24 max.
1
2
3
4
5
6
7
8
9
10
13.2
11
(Bottom View)
5.8
4.1
1.0
PY11-02
* The structure does not resist flux. Manual
soldering is recommended for this product.
6.35
0.3
25.5 max.
29.5 max.
6.4
4.2
2.7
4.3
22 max.
12.65
Eleven, 1.3-dia holes
2
16.5 max.
16
Products Related to Common Sockets and DIN Tracks
Terminal
Arrangement/
Internal
Connections
Dimensions
*
PY14
PY14-Y1 (L = 42 max.)
PY14-Y3 (L = 60 max. )
Mounting hole and PCB dimensions
Fourteen, 3 x 1.2 ellipses
25.5 max.
29.5 max.
5
25.8±0.2
The PY14-Y@ includes
the part outlined by the
dashed lines above.
PY14QN
PY14QN2
PY14QN-Y1 (L = 42 max.)
PY14QN2-Y1 (L = 42 max.)
PY14QN-Y3 (L = 60 max.)
PY14QN2-Y3 (L = 60 max.)
2.6
7.7
2.7
*
24 max.
20 max.
L
21.4+0.2
0
1
*1
29.5 max.
1 2 3 4
5
(20)*2
25
41.5 max.
(36.5 max.)*2
2.7
L
5 6 7 8
22 max.
9 10 11 12
24 max.
13
*1. The PY14QN-Y@ and PY14QN2-Y@ include the part outlined
by the dashed lines above.
*2. The figures in the parentheses are for the PY14QN2(-Y@).
* The structure does not resist flux. Manual
soldering is recommended for this product.
13.2
(Bottom View)
4.4
5.8
1.0
PY14-02
14
4.1
0.3
6.35
25.5 max.
29.5 max.
2.7
4.3
6.4
4.2
22 max.
12.65
Fourteen
1.3-dia. holes
2
16.5 max.
Note: 1. Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it.
2. You can use the PY14-Y1 or PY14QN-Y1 for the MY4 Series, MY4H, MYQ4(Z), or MY2K.
3. You can use the PY14-Y3 or PY14QN-Y3 for H3Y Timers.
PTF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
PTF08A
Two, 4.5 × 6
mounting holes
Mounting Hole Dimensions
3.4
7±0.2
8-M3.5×8
78.5 max.
35.4
Two, 4.5 dia. or
M4 mounting holes
8
30 max.
28.5 max.
2 1
4
3
PTF08A-E (Finger Protection Structure)
Two, 4.5 × 6
mounting holes
68±0.3
3.4
8-M3.5×8
6
5
8 7
(Top View)
19±0.2
(Top View)
78.5 max.
35.5
Note: Track mounting is also
possible.
Refer to page 27.
28.5 max.
8
33 max.
17
Products Related to Common Sockets and DIN Tracks
Terminal Arrangement/
Internal Connections
Dimensions
Mounting Hole Dimensions
PTF11A
Two, 4.5 × 6 mounting holes
Two, 4.5 × 6
mounting holes
3.4
7±0.2
11-M3.5×8
3 2 1
6 5 4
68±0.3
35.4
78.5 max.
9 8 7
11
27.5±0.2
(Top View)
(Top View)
8
37 max.
10
Note: Track mounting is also possible.
Refer to page 27.
30 max.
Two, 4.5 × 6
mounting holes
PTF14A
3.4
7±0.2
14-M3.5×8
78.5 max.
35.4
Two, 4.5 dia. or M4 mounting holes
4 3 2 1
45.5 max.
8
30 max.
8 7 6 5
PTF14A-E (Finger Protection Structure)
Two, 4.5 × 6
mounting holes
68±0.3
3.4
7±0.2
12 11 10 9
14-M3.5×8
13
14
36±0.2
(Top View)
(Top View)
78.5 max.
35.5
Note: Track mounting is also possible.
Refer to page 27.
45.5 max.
8
33 max.
Note: If you use the PTF08A, PTF08A-E, or PT08 with an LY1 Relay, connect the following terminal pairs: 1-2, 3-4, and 5-6 (for usage at 10 A or
higher).
PT
(Unit: mm)
Terminal
Arrangement/
Internal
Connections
Dimensions
PT08
PT08QN
5
1.5×1.0
0.3
25.5 29.5
1.0 max. max.
25.5 29.5
max. max.
2.7
9 2.5
20
1.5
35 max.
2.7
24 max.
20.5 max.
Mounting hole and PCB dimensions
25.8±0.2
2
21.4+0.2
0
24 max.
2
Eight, 1.7-dia × 3.5 oblong holes
PT08-0
2
0.3
*Maintain
a sufficient distance from the
pattern when using double-sided PCBs.
• The structure does not resist flux.
Manual soldering is recommended for
this product.
7
1
2
3
4
5
6
15.6
10
8
(Bottom View)
5.35
4.6
6.45
29.5 max.
2
1
18 max.
4.3
5*
6.5
22 max.
12.45
6.5
3
Eight, 2.5-dia. holes
(±0.1 tolerance)
18
Products Related to Common Sockets and DIN Tracks
Terminal
Arrangement/
Internal
Connections
Dimensions
PT11
Mounting hole and PCB dimensions
PT11QN
0.3
1.5×1.0
5
1.5 30.6 32
max.
Eleven, 1.7-dia × 3.5 holes
31±0.2
32
30.6
max.
2.7
9 2.5
20
1.0
1.2
35 max.
2.7
1.2
26.4
26.6+0.3
0
29.5 max.
26.4
10 7
4
1
8
5
2
11 9
6
3
29.5 max.
20.5 max.
PT11-0
*Maintain
0.3
a sufficient distance from the
pattern when using double-sided PCBs.
• The structure does not resist flux.
Manual soldering is recommended for
this product.
(Bottom View)
12.45
6.45 4.6
Eleven,
2.5-dia. holes
5.2
10
21.4
2
5*
10
32 max.
5.8
2.7
4.3
18 max.
PT14
6.2
6.2
5.65
(±0.1 tolerance)
29.5 max.
PT14QN
0.3
1.5×1.0
5
Fourteen, 1.7-dia × 3.5 holes
42.5 max.
1.5
42.5 max.
2.7
9 2.5
1.0
20
35 max.
26.5 max.
29.5 max.
2.7
20.5 max.
26.5 max.
29.5 max.
PT14-0
*Maintain
0.3
41±0.2
a sufficient distance from the
pattern when using double-sided PCBs.
• The structure does not resist flux.
Manual soldering is recommended for
this product.
26.6+0.3
0
13 9
5
1
10 6
2
11 7
3
14 12 8
12.45
4.6
6.45
4
5.1
5.8
(Bottom View)
10
31.4
2
2.7
4.3
10
42.5 max.
5*
10
Fourteen,
2.5-dia. holes
6.4
6.4
17.5 max.
26.5 max.
29.5 max.
5.45
(±0.1 tolerance)
Note: Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it.
19
Products Related to Common Sockets and DIN Tracks
P7LF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
P7LF-06
Mounting Hole Dimensions
Two, M3.5 x 6 (coil side)
51.5 max.
0
Four, M4 × 8
(contact side)
40±0.1
25
1
Two, 4.5 dia. or
M4 mounting holes
5
46 max.
40±0.1
55.5 max.
2 4
6 8
(Top View)
8±0.05
9.2±0.05
P7S
(Unit: mm)
Terminal Arrangement/Internal
Connections
Dimensions
Mounting Hole Dimensions
P7S-14F-END
Indicator LED
14-M3.0×8
40 max.
33±0.1
41
43
4
42
44
1
7.5
34
23
62
14
13
Two, 4.0 dia.
or M3.5
33
24
61
0
52
33±0.1
51
80 max.
37
17
3.1
5
5.9
90.5 max.
(5)
P7S-14P-E
70.5 max.
28±0.2
G7S-4A2B-E Mounted
23.5 max.
28±0.2
4.2
Two, 6.5 dia., depth: 8
(21)
2.8
G7S-3A3B-E Mounted
(16.9)
14.5 8
57 max.
Fourteen,
2.5 dia.
6
7
5×7=35
Two,
3.6 dia.
13.2
(15)
7
6
5×7=35
16.9
8
4.1
14.5
23.5 max.
20
Products Related to Common Sockets and DIN Tracks
P7SA
(Unit: mm)
Dimensions
Terminal Arrangement/Internal Connections
P7SA-10F
P7SA-10F-ND
G7SA-3A1B
Mounted
Mounting Hole Dimensions
G7SA-2A2B
Mounted
14.5±0.2
Two, 4 dia.
or M3.5
R2
22.5 max.
60.5 max.
10-M 3× 8
44
5
9 max.
33
44
34
43
43
24
22
33
34
80±0.2
*
72 max.
*
23
Indicator
LED
21
12
12
11
1
0
11
1
0
9 max.
4 dia.
Note: 1. The Socket is shown with the finger
cover removed.
2. Only the -ND Sockets have LED
indicators (orange).
P7SA-14F
P7SA-14F-ND
(Top View)
* This display circuit is available only for "-ND" models.
Note: Terminals 23-24, 33-34, and 43-44 are normally
open. Terminals 11-12 and 21-22 are normally
closed.
G7SA-5A1B
Mounted
G7SA-4A2B
Mounted
G7SA-3A3B
Mounted
22±0.2
R2
30 max.
64
54
64
54
64
54
63
53
63
53
63
53
44
34
44
34
44
32
60.5 max.
14-M3×8
9 max.
Two, 4 dia.
or M3.5
5
*
72 max.
Indicator
LED
9 max.
4 dia.
*
33
43
33
43
31
24
12
22
12
22
12
11
21
11
21
23
Note: 1. The Socket is shown with the finger
cover removed.
2. Only the -ND Sockets have LED
indicators (orange).
*
43
1
0
1
0
1
0
80±0.2
11
* This display circuit is available only for "-ND" models.
Note: Terminals 23-24, 33-34, 43-44, 53-54, and 63-64 are
normally open. Terminals 11-12, 21-22, and 31-32 are
normally closed.
(Top View)
G7SA-3A1B Mounted
P7SA-10P
0.5
50 max.
0.5
0
11 12
33 34
1
23 24
43 44
+
−
15 max.
4.1±0.2
39.9±0.2
24.8±0.2
Three, 3.2 dia.
(for M3 tapping
screws)
G7SA-2A2B Mounted
10.16
41.5 max.
0
11 12
33 34
+
−
(7.14)
1
0.4
(11.1)
5.08 5.08
43 44
Ten,
1.1 dia. holes
3.5
(11.1)
0.8
(Bottom View)
(Bottom View)
Three, 2.6 dia.
(for M3 tapping screws)
4.1
21 22
13.97 11.43
Note: Terminals 23-24, 33-34, and 43-44 are
normally open. Terminals 11-12 and 2122 are normally closed.
24.8
39.9
(±0.1 tolerance)
G7SA-5A1B Mounted
P7SA-14P
0.5
60 max.
0.5
0
11 12
33 34 53 54
1
23 24
43 44 63 64
+
−
15 max.
G7SA-4A2B Mounted
0
11 12
33 34 53 54
1
21 22
43 44 63 64
+
−
41.5 max.
4.1±0.2
10.16
G7SA-3A3B Mounted
0.4
0
3.5
(11.1)
(11.1)
0.8
Three, 2.6 dia.
(for M3 tapping screws)
11 12
31 32 53 54
21 22
43 44 63 64
+
−
1
Three, 3.2 dia.
49.9±0.2
(for M3 tapping
24.8±0.2 Fourteen,
1.1 dia. holes screws)
(7.14)
13.97 11.43
5.08
5.08 5.08 5.08
(Bottom View)
(Bottom View)
4.1
24.8
49.9
Note: Terminals 23-24, 33-34, 43-44, 53-54, and 6364 are normally open. Terminals 11-12, 21-22,
and 31-32 are normally closed.
(±0.1 tolerance)
21
Products Related to Common Sockets and DIN Tracks
PF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
PF083A
Mounting Hole Dimensions
4
7±0.2
8-M3.5×7
Two,
4.2 dia. holes
52 max.
35.4
2 1 8 7
PF083A-E
3.5
33
41 max.
4
2
21 max.
7±0.2
8-M3.5×7
4
Two, 4.2-dia
mounting holes
3 4 5 6
8 25 dia.
52 max.
35.4
Two M4 or 4.5-dia. holes
(Top View)
33±0.2
4
3.5
23
33
41 max.
PF085A
Note: Track mounting is also
possible.
Refer to page 27.
2
21 max.
4
7±0.2
8-M3.5×7
6 5 4 3
Two,
4.5 dia. holes
58 max.
35.4
1.1
33±0.2
40 max.
4
7 8 1 2
2
3.5
(Top View)
21.6 max.
PF113A
11-M3.5×7
4
22
7±0.2
35.4
52 max.
4
5
PF113A-E
34
43 max.
4
3.5
2 1 11 10
9
Two M4 or 4.5-dia. holes
31 max.
4
7±0.2
11-M3.5×5
3
2
34±0.2
4
5 6 7 8
52 max.
8
35.4
(Top View)
4.2
Note: Track mounting is also
possible.
Refer to page 27.
4
5.2
3.5
23
42.8
5.5
31 max.
Note: 1. For the PF083A and PF113A, the Socket key slot is on the top. (Applicable model: MK)
2. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
22
Products Related to Common Sockets and DIN Tracks
P2CF
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
P2CF-08
8-M3.5×7.5
7.8
3
Mounting Hole Dimensions
4.5
Two,
4.5 dia. holes
70 max.
35.4
6 5 4 3
50 max.
4
20.3 max.
Two M4 or 4.5-dia. holes
P2CF-08-E
8-M3.5×7.5
5
7.8
4.5
40±0.2
6
5
4
3
Two,
4.5 dia. holes
P2CF-08-E
3
7 8 1 2
1.3
70 max.
35.4
(Top View)
Note: Track mounting is also
possible.
Refer to page 27.
10A250VAC
RESISTIVE
7
8
1
2
40±0.2
50 max.
4
19
20.3
21.5 max.
P2CF-11
11-M3.5×7.5
7.8
3
4.5
Two,
4.5 dia. holes
70 max.
35.4
8 7 6 5
P2CF-11-E
4
50 max.
4
Two M4 or 4.5-dia. holes
31.2 max.
11-M3.5×7.5
7.8
5
40±0.2
4.5
9
8
7
6
5
Two,
4.5 dia. holes
P2CF-11-E
4
10 11 1 2
3
(Top View)
1.2
70 max.
9
3
35.4
Note: Track mounting is also
possible.
Refer to page 27.
3
10A250VAC
RESISTIVE
10
4
11
1
40±0.2
50 max.
2
30
31.2 max.
23
Products Related to Common Sockets and DIN Tracks
PFA
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
Mounting Hole Dimensions
8PFA
8-M3.5×7
7.8±0.2
Two,
4.5 dia. holes
5
4
4
35.4
81 max.
4
118
max.
40±0.2
6 5 4 3
51 max.
24 max.
Two M4 or 4.5-dia. holes
8PFA1
8-M3.5×7
40±0.2
7.8±0.2
7 8 1 2
Note: Track mounting is also
possible.
Refer to page 27.
4
Two,
4.5 dia. holes
5
(Top View)
4
93 max.
4
35.4
130
max.
40±0.2
51 max.
24 max.
11PFA
11-M3.5×7
7.8±0.2
Two,
4.5 dia. holes
5
4
8 7 6 5
4
4
81 max.
35.4
Two M4 or 4.5-dia. holes
118
max.
40±0.2
9
3
10 11 1 2
4
Note: Track mounting is also
possible.
Refer to page 27.
(Top View)
40±0.2
51 max.
33.5 max.
14PFA
7.8±0.2
14-M3.5×7
Two,
4.5 dia. holes
5
4
7 14 6 5 12 4
3
4
35.4
81 max.
118
max.
Two, 4.5 dia. or M4 mounting holes
60±0.2
8
9 15 10 1 11 2
4
(Top View)
60±0.2
72 max.
Note: Track mounting is also
possible.
Refer to page 27.
33.5 max.
24
Products Related to Common Sockets and DIN Tracks
P3G/P3GA
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
P3G-08
Mounting Hole Dimensions
27 dia.
3 4 5 6
45
--2 1 8 7
4.9
45
Eight,
M3.5 SEMS screws
17
(Bottom View)
Note: The Y92A-48G Terminal Cover can be used to
implement finger protection.
P3GA-11
27 dia.
5 6 7 8
4
25.6
45
3
4.5
45
Eleven,
M3.5 SEMS screws
6.2
16.3
9
2 1 11 10
---
(Bottom View)
Note: The Y92A-48G Terminal Cover can be used to
implement finger protection.
Terminal Cover
(Unit: mm)
Appearance
Dimensions
Y92A-48G
34
Twelve, 6.4 dia.
Y92A-48G
UP
47.7 × 47.7
48 × 48
P C
16.5
24.6 27.6
47.4
Release Lever
Applicable models
Appearance
(Unit: mm)
Dimensions
Model
16
PYF08S
PYCM-08S
54.4
32.7
28
PYF14S
PYCM-14S
52.5
29.6
16.8
P2RF-05-S
40.35
P2CM-S
P2RF-08-S
36
25
Products Related to Common Sockets and DIN Tracks
PL
(Unit: mm)
Terminal Arrangement/
Internal Connections
Dimensions
Mounting hole and PCB dimensions (bottom view)
Two, 3.5 dia. or M3
device mounting holes
PL08
3.5
4
Two, 3.5 or M3
Socket mounting holes
1
Two,
2 dia. holes
31-dia. hole
30 dia.
50.5 max.40
40±0.3 L
3.9
Approx.
20.5
50.5 max.
PL08-Q
4
3.5
1
4
t0.6×1.3
5
3
6
2
51 max. 40
L = 40 mm
MK2(Z)P
L = 74 mm
PU, AMD-S, MM2(X)P, CZ, STP, H3L,
TDS, DTS, DSP, TDF, TDV
L = 86 mm
61F-GP/-APN, G4Q-212S, RD2P,
RDA, TDA, AGF, SE, SAD, K2CU,
SDV-F
Two 3.5-dia. or
two M3 Socket mounting holes
7
1
30 dia.
8
MK2(Z)P
31-dia. hole
40±0.3
(Bottom View)
16
35 max.
35 max.
PLE08-0
15
14
Two 3.5-dia.
Hold-down Clip mounting holes
t0.3
45°
40+0.1
0
27.7±0.5 dia.
29±0.1 dia.
Eight, 2.5-dia. holes
21.5 max.
PL11
3.5
4
1
Two 2-dia.
holes
51 max. 40
Two, 3.5 dia. or M3 device mounting
/Hold-down Clip mounting holes
30 dia.
3.9
L = 40 mm
MK3P
MK2KP
Two, 3.5 dia. or M3
Socket mounting holes
Approx.
20.5
35 max.
PL11-Q
3.5
4
31-dia. hole
1
40±0.3 L
5 6 7
t0.6×1.3
51 max.
16
4
3
2
1 11
8
9
10
PLE11-0
Two, 3.5-dia. holes
Applicable model/Hold-down Clip mounting holes
t0.3
360°
11
28.7±0.5
29±0.1 dia.
22 max.
4
L = 40 mm
MK3P
MK2KP
L
L = 42 mm
MK3ZP
MK3LP
Eleven, 2.5-dia. holes
Two, 3.5 dia. or M3
device mounting holes
1
Two 2-dia.
holes
41 max.
66 max. 53
L = 42 mm
MK3ZP
MK3LP
(Bottom View)
14 15
4
L = 74 mm
MM3P
MK2(X)KP
35 max.
35 max.
PL15
MK2(Z)P
3.9
2 3 4
12
5
1 11
13
10 15
6
14
9 8 7
MM3XP
MM4(X)P
MM3(X)KP
MM4(X)KP
Two, 3.5 dia. or M3
Socket mounting holes
4.2-dia. hole
74
(Bottom View)
45 max.
22 max.
53
26
Products Related to Common Sockets and DIN Tracks
Terminal Arrangement/
Internal Connections
Dimensions
PL20
Two, 3.5-dia. holes 4
Two, 4.5-dia. Relay
mounting holes
1
Two, 2 dia.
46.5 max.
Mounting hole and PCB dimensions (bottom view)
Two, 4-dia.
Socket mounting
holes
33-dia. hole
19 1
17 18 20 2 3
16
4
15
5
6
14
13 12 10 8 7
11 9
31 max.
3.9
36.5 max.
56±0.2
* Relay mounting holes are not
required for the LDNP.
(Bottom View)
23 max.
38±0.2
Note: When mounting, pay due attention to the direction of the key groove of applicable Relays.
Accessories for DIN Track Mounting (Order Separately)
(Unit: mm)
DIN Tracks
PFP-100N
PFP-50N
7.3±0.15
4.5
27±0.15
35±0.3
15
25
10
25
25
1,000 (500)*
15 (5)*
25
10
1
*
Dimensions in parentheses are for the PFP-50N.
DIN Track
PFP-100N2
Model
PFP-100N
PFP-50N
16
4.5
35±0.3 27
15
25
10
25
25
1,000
End Plate
25
10
24
29.2
Model
15
1
1.5
PFP-100N2
10
6.2
PFP-M
50
M4×8
panhead
screw
1.8
1
35.5 35.3
1.8
11.5
Model
10
M4 screw and washer
Spacer
1.3
4.8
PFP-M
16
12
5
PFP-S
34.8
44.3
Model
PFP-S
16.5
Note: 1. Order the above products in multiples of 10.
2. The Tracks conform to DIN standards.
27
Products Related to Common Sockets and DIN Tracks
Features of Screwless Sockets
Structured for Easy Wiring
Contact terminal
(common)
Contact terminal
(NO)
Contact terminal
(NC)
Release Lever
(sold separately)
Coil terminals
Nameplate
(sold separately)
Complete Wiring in Three Steps
Insert a
screwdriver.
Screwdriver
inserted.
Insert the wire.
Remove screwdriver
to complete wiring.
• A spring holds the wire in place to reduce wiring work by
30% (according to OMRON comparison) and eliminates the
need to manage torque.
• DIN terminal numbers also indicated.
Safety Precautions
Precautions for Safe Use
• Do not move the screwdriver up, down, or from side to side or rotate it while it is inserted in the hole. Doing so may damage internal components in the
Socket.
• Do not insert more than one wire into the same hole. Doing so may cause abnormal heating.
• There are two internally connected wiring holes for each terminal.
• Insert the screwdriver along the hole wall as shown below.
Screwdriver
• When you remove a Socket from a support rail, insert the end of a screwdriver into the fixture and move the driver as shown by the arrow in the
following figure.
Screwdriver
Fixture rail
• When you use a Release Lever to remove a Relay from a P2RF-@@-S Socket, insert a screwdriver at the location shown in the following figure
and move the Release Lever in the direction indicated by the arrow to release the lock on the release lever.
28
Products Related to Common Sockets and DIN Tracks
Precautions for Correct Use
Wiring Tools
Applicable Screwdriver
Use a flat-blade screwdriver with a tip that is 2.5 mm wide (3.0 mm
max.).
2.5 mm (3.0 mm max. )
You cannot use a screwdriver with a thick shaft.
Applicable Screwdriver (Example)
VESSEL No.9900 − (−) 2.5 × 75
Applicable Wires
• You can use either solid wires or stranded wires. Applicable wire
size: 0.2 to 1.5 mm2 (AWG24 to AWG16)
• Strip 8 to 9 mm of insulation from the ends of the wires.
8 to 9 mm
• If you insert stranded wires without ferrules, make sure that the
wires are twisted when you insert them.
• If you use bare ferrules, always attach insulating sleeves.
• If you insert a wire with a sheath outer diameter of 2.2 mm or less,
do not insert the wire far enough so that the sheath is engaged
inside the hole, as shown below.
• Two wires with a sheath outer diameter of 3.2 mm or larger cannot
be inserted for the same terminal at the same time.
• Use heat-shrinking tubes to indicate wire numbers.
29
Products Related to Common Sockets and DIN Tracks
Wiring
12
11
10
9
41
31
21
11
Wire insertion holes
Screwdriver insertion hole
(1) Insert a screwdriver into a screwdriver insertion hole on the
Socket.
Cross-section A-A
Spring
Wire insertion hole
Screwdriver
Screwdriver insertion hole
(2) Press the screwdriver in until it reaches the stopper inside the
Socket. The spring at the back of the wire insertion hole will be
complete open in this condition. The screwdriver will be held in place
even if you remove your hand.
(3) With the screwdriver held in place, insert the wire or ferrule into the
wire insertion hole.
Wire
(4) Remove the screwdriver. The spring will hold the wire. This
concludes the connection procedure.
30
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2016.4
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2016 All Right Reserved.