Download

Round Water-resistant Connectors (M12 Smartclick)
XS5
CSM_XS5_DS_E_13_2
Round Water-resistive Smartclick
Connectors That Reduce Installation Work
• A newly developed lock mechanism that is compatible with round M12 connectors.
• Simply insert the Connectors, then turn them approximately 1/8 of a turn to lock.
• A positive click indicates locking.
• Features the same degree of protection (IP67) as M12 connectors.
• A full line-up of models is planned.
• Connectors with Cables are UL approved.
Refer to Safety Precautions on page 24.
Ratings and Specifications
Rated current
4A
Rated voltage
250 VDC
Contact resistance (connector)
40 mΩ max. (20 mV max., 100 mA max.)
Insulation resistance
1,000 MΩ min. (at 500 VDC)
Dielectric strength (connector)
1,500 VAC for 1 min (leakage current: 1 mA max.)
Degree of protection
IP67 (IEC60529)
Insertion tolerance
50 times min.
Lock strength
Tensile: 100 N/15 s, Torsion: 1 N·m/15 s
Cable holding strength
Tensile: 100 N/15 s, Torsion: 1 N·m/15 s (for cable diameter of 6 mm) *2
Lock operating force
0.1 to 0.25 N·m
Ambient operating temperature range
−25 to 70°C
Ambient humidity range
20% to 85%
Number of pressure-weld repairs *1
10 times max. (Limited to the same external diameter and wire diameter.)
*1. Only XS5C/G (IDC models)
*2. Refer to product specifications for details.
1
XS5
Materials and Finishes
Model
XS5F/H/W
Item
XS5R
Phosphor bronze
or Brass
Material
Phosphor bronze
Finish
Nickel base, 0.4-μm gold plating
Contacts
Fixtures
Nickel-plated zinc alloy
Fixtures (Lock) *
Stainless
Pin block
PBT resin (UL94V-0)
O-ring
Rubber
Overmolding/Cover
Soft PBT resin (UL94V-0)
UL AWM2464 CL3, 6 mm dia.,
Fire-retardant,
AWG20 (0.5mm2)
Robot cable
Structure: 0.08 mm/110 wires
Oil-resistant 6 mm dia.
Cable polyurethane AWG20 (0.5mm2)
cable
Structure: 0.12 mm/45 wires
6.6 mm dia.
Spatter-resisAWG20 (0.5mm2)
tant Cable
Structure: 0.08 mm/100 wires
XS5C/G
(Crimping, Soldering)
XS5M/P
Phosphor bronze
Brass
XS5C/G
(Screw-on)
XS5C/G
(IDC models)
Phosphor bronze
or Brass
Phosphor bronze
Nickel base, 0.15μm gold plating
---
PBT resin (UL94V-0)
---
---
---
Seal resin
---
Epoxy resin
(UL94V-0)
---
Power supply wires
---
UL1007 AWG20
---
*Only plug
Connector Pinout Diagram (from Mating Side)
Item
No. of poles
4 poles
1
4
Male (plug) contacts
2
3
DC type
2
Female (socket) contacts
3
1
4
Connection Combinations
Smartclick Plug Connectors
M12 Plug Connectors
XS5H, XS5G, XS5W (plug side),
XS5R (plug side), XS5M
XS2H, XS2G, XS2W (plug side),
XS2R (plug side), XS2M
Smartclick Socket XS5F, XS5C, XS5W (socket side),
Connectors
XS5R (socket side), XS5P

❍
M12 Socket
Connectors
❍
❍
OMRON model No.
XS2F, XS2C, XS2W (socket side),
XS2R (socket side), XS2P
is a registered trademark of the OMRON Corporation.
 : Connected by twisting.
❍ : Connected by screwing.
Note: The XS@M and XS@P cannot mate with each other.
2
XS5
XS5W
Connectors Connected to Cable, Socket and Plug on Cable Ends
● Fire-retardant, Robot cable
● Oil-resistant Polyurethane Cable
● Spatter-resistant Cable
XS5W-D42@-@81-F
XS5W-D42@-@81-P
XS5W-D421-@81-SA
Dimensions
(Unit: mm)
Straight/straight
M12×1
14.9 dia.
14.9 dia.
40.7
44.7
L (Cable length)
Angled/angled
M12×1
14.9 dia.
14.9 dia.
32.3
28.3
Wiring Diagram for 4 Cores
Pin No.
L (Cable length)
Straight/angled
M12×1
1
2
3
4
14.9 dia.
Cable color of
core sheath
1
Brown
2
White
3
Blue
4
Black
32.3
14.9 dia.
40.7
L (Cable length)
Angled/straight
14.9 dia.
M12×1
28.3
14.9 dia.
44.7
L (Cable length)
Note: Oil-resistant Polyurethane Cables (XS5W-D42@-@81-P) and Spatter-resistant Cable (XS5W-D421-@81-SA) have black covers.
Fire-retardant, Robot cable (XS5W-D42@-@81-F) have warm gray covers.
3
XS5
Model Number Legend
XS5W-D42@-@81-@@
1
2
3 4
5
6
7 8
Use this model number legend to identify products
from their model number. When ordering, use a model number from the table in Ordering Information.
9
1. Type
W: Connectors connected to cable, socket and plug
on cable ends
6. Cable Length
2. Mating Section Form
D: DC
7. Connections
C: 1 m
G: 5 m
D: 2 m
J: 10m
E: 3 m
8: A Brown, B White, C Blue, D Black (Numbers
inside circles are terminal numbers)
3. Connector Poles
4: 4 poles
8. Connectors on One End/Both Ends
4. Contact Plating
2: 0.4-μm gold plating
1: Both ends
9. Cable Specifications
5. Cable Connection Direction
1: Straight/straight
2: Angled/angled
3: Straight (Socket)/angled (Plug)
4: Angled (Socket)/straight (Plug)
F: Fire-retardant, Robot cable
P: Oil-resistant Polyurethane Cable
SA: Spatter-resistant Cable
Ordering Information
Cable specifications
Fire-retardant, Robot
cable
Cable
Cable outer
length L (m) diameter (mm)
1
XS5W-D421-C81-F
XS5W-D421-D81-F
3
XS5W-D421-E81-F
5
Spatter-resistant
Cable
Cable specifications
Fire-retardant, Robot
cable
6
Angled/angled
Model
2
10
Oil-resistant Polyurethane Cable
Straight/straight
-----
XS5W-D421-G81-F
---
XS5W-D421-D81-P
---
XS5W-D421-G81-P
---
10
XS5W-D421-J81-P
---
6.6
Cable
Cable outer
length L (m) diameter (mm)
2
5
6
10
5
Yes
XS5W-D422-G81-F
XS5W-D421-J81-F
2
2
UL
XS5W-D422-D81-F
5
5
Minimum
order
XS5W-D421-D81-SA
---
XS5W-D421-G81-SA
---
Straight (Socket)/
angled (Plug)
Angled (Socket)/
straight (Plug)
Model
XS5W-D423-D81-F
XS5W-D424-D81-F
XS5W-D423-G81-F
XS5W-D424-G81-F
1
5
---
1
5
---
Minimum
order
UL
5
Yes
4
XS5
XS5F
Connector Connected to Cable, Socket on One Cable End
● Fire-retardant, Robot cable
● Oil-resistant Polyurethane Cable
● Spatter-resistant Cable
XS5F-D42@-@80-F
XS5F-D42@-@80-P
XS5F-D421-@80-SA
Dimensions
(Unit: mm)
Straight
L (Cable length)
40.7
Wiring Diagram for 4 Cores
14.9 dia.
Cable color of
core sheath
Brown
White
Blue
Black
Pin No.
M12 × 1
30
5
1
2
3
4
50
Angled
L (Cable length)
25.3
M12×1
28.3
30
5
50
14.9 dia.
Note: Oil-resistant Polyurethane Cables (XS5F-D42@-@80-P) and Spatter-resistant Cable (XS5F-D421-@80-SA) have black covers. Fireretardant, Robot cable (XS5F-D42@-@80-F) have warm gray covers.
Model Number Legend
XS5F-D42@-@80-@@
1
2
3 4
5
6
7 8
Use this model number legend to identify products
from their model number. When ordering, use a model number from the table in Ordering Information.
9
1. Type
F: Connector connected to cable,
socket on one cable end
5. Cable Connection Direction
1: Straight
2: Angled
2. Mating Section Form
D: DC
6. Cable Length
C: 1 m
D: 2 m
G: 5 m
J: 10 m
3. Connector Poles
4: 4 poles
8. Connectors on One End/Both Ends
0: One end
9. Cable Specification
F: Fire-retardant, Robot cable
P: Oil-resistant Polyurethane Cable
SA: Spatter-resistant Cable
E: 3 m
7. Connections
8: A Brown, B White, C Blue,
D Black (Numbers inside circles are
terminal numbers.)
4. Contact Plating
2: 0.4-μm gold plating
Ordering Information
Cable specifications
Fire-retardant, Robot cable
Oil-resistant
Polyurethane Cable
Spatter-resistant
Cable
Cable length L (m)
1
2
3
5
10
2
5
10
2
5
Cable outer
diameter (mm)
6
6.6
Straight Connectors
Angled Connectors
Model
XS5F-D421-C80-F
XS5F-D421-D80-F
XS5F-D421-E80-F
XS5F-D421-G80-F
XS5F-D421-J80-F
XS5F-D421-D80-P
XS5F-D421-G80-P
XS5F-D421-J80-P
XS5F-D421-D80-SA
XS5F-D421-G80-SA
XS5F-D422-C80-F
XS5F-D422-D80-F
XS5F-D422-E80-F
XS5F-D422-G80-F
XS5F-D422-J80-F
XS5F-D422-D80-P
XS5F-D422-G80-P
XS5F-D422-J80-P
-----
Minimum
order
UL
10
5
Yes
1
5
---
1
5
---
5
XS5
XS5H
Connector Connected to Cable, Plug on One Cable End
● Fire-retardant, Robot cable
● Oil-resistant Polyurethane Cable
● Spatter-resistant Cable
XS5H-D42@-@80-F
XS5H-D42@-@80-P
XS5H-D421-@80-SA
Dimensions
(Unit: mm)
Straight
L (Cable length)
44.7
Wiring Diagram for 4 Cores
14.9 dia.
30
M12×1
5
Angled
Cable color of
core sheath
Brown
White
Blue
Black
Pin No.
50
1
2
3
4
L (Cable length)
25.3
32.3
30
5
50
M12×1
14.9 dia.
Note: Oil-resistant Polyurethane Cables (XS5H-D42@-@80-P) and Spatter-resistant Cable (XS5H-D421-@80-SA) have black covers. Fireretardant, Robot cable (XS5H-D42@-@80-F) have warm gray covers.
Model Number Legend
XS5H-D42@-@80-@@
1
2
3 4
5
6
7 8
1. Type
H: Connector connected to cable,
plug on one cable end
2. Mating Section Form
D: DC
3. Connector Poles
4: 4 poles
4. Contact Plating
2: 0.4-μm gold plating
Use this model number legend to identify products
from their model number. When ordering, use a model number from the table in Ordering Information.
9
8. Connectors on One End/Both Ends
0: One end
9. Cable Specifications
5. Cable Connection Direction
1: Straight
2: Angled
6. Cable Length
A: 0.3 m C: 1 m
G: 5 m
7. Connections
F:
P:
Fire-retardant, Robot cable
Oil-resistant Polyurethane
Cable
SA: Spatter-resistant Cable
D: 2 m
8: A Brown, B White, C Blue,
D Black (Numbers inside circles
are terminal numbers)
Ordering Information
Cable specifications
Fire-retardant, Robot cable
Oil-resistant
Polyurethane Cable
Spatter-resistant
Cable
Cable length L (m)
0.3
1
2
5
0.3
2
5
0.3
1
Cable outer
diameter (mm)
6
6.6
Straight Connectors
Angled Connectors
Model
XS5H-D421-A80-F
XS5H-D421-C80-F
XS5H-D421-D80-F
XS5H-D421-G80-F
XS5H-D421-A80-P
XS5H-D421-D80-P
XS5H-D421-G80-P
XS5H-D421-A80-SA
XS5H-D421-C80-SA
XS5H-D422-A80-F
XS5H-D422-C80-F
XS5H-D422-D80-F
XS5H-D422-G80-F
XS5H-D422-A80-P
XS5H-D422-D80-P
XS5H-D422-G80-P
-----
Minimum
order
UL
10
Yes
5
10
5
10
---
---
6
XS5
XS5@ Eight-pole Connectors with Cables
Ordering Information
Type
Cable specification
Cable connection
direction
No. of cable
cores
Connector Connected to
Cable, Socket on One End
6.3 mm dia.,
AWG23 (0.25 mm2)
Structure: 0.08 mm/60 wires
Straight
10
Panel-mounting Plug
---
---
---
Cable length L
(m)
2
5
10
---
Applicable wire
gauge
--AWG22 to AWG28
Model
XS5F-D821-DH0-R
XS5F-D821-GH0-R
XS5F-D821-JH0-R
XS5M-D827-4
Pins and Cable Lead Colors
A
White
XS5F cable lead colors
B
Brown
Ratings and Specifications
Rated current
Rated voltage
Contact resistance
Insulation resistance
Dielectric strength
Degree of protection
Insertion tolerance
Ambient operating temperature range
Ambient operating humidity range
Pin No.
D
E
Yellow
Gray
C
Green
F
Pink
G
Blue
H
Red
Materials and Finishes
Contacts
Fixtures
Body
Nuts
Fixtures (lock)
Contact block
Cover *1
Seal resin *2
O-ring*1
1.5 A
36 VDC
40 mΩ max.
(at 20 mV DC max., 100 mA max.)
1,000 MΩ min. (at 500 VDC)
1,000 VAC for 1 min
(leakage current: 1 mA max.)
IP67 (IEC 60529)
50 times
−25 to 70°C
20% to 85%
Brass/nickel base, 0.4-μm gold plating
Nickel-plated zinc alloy *1
Nickel-plated zinc alloy *2
Nickel-plated brass *2
Stainless *2
PBT resin (UL94V-0), light gray
Soft PBT resin (UL94V-0)
Rubber
*1. XS5F only.
*2. XS5M only.
Dimensions
(Unit: mm)
XS5F-D821-@H0-R Connector Connected to Cable, Socket on One End
L (cable length)
1
2
40.7
3
7
14.9 dia.
4
6
8
(5)
(30)
5
(50)
M12×1
XS5M-D827-4 Front-locking, Panel-mounting Plug
Nut
3
5
3
(19)
M16×1
M12×1
Seal resin
(21.9)
Eight, 1 dia
17
Pin No.
8
2
2.8
20 dia.
Resin filling
22.8
Panel Cutout
14.1+0.1
0
16.1+0.1
0 dia.
16.1+0.1
0 dia.
Panel Cutout
Panel thickness (t): 1 to 4
7
XS5
XS5G Assembly Connector Plugs
Dimensions
(Unit: mm)
XS5G-D418 (IDC Model)
Straight Connectors
66
M12 × 1
58
17.5 dia. 14.9 dia.
XS5G-D4C@ (Crimping Model)
XS5G-D42@ (Soldering Model)
Straight Connectors
M12 × 1
14.9 dia.
14.2 dia.
49.3
XS5G-D42@ (Soldering Model)
Angled Connectors
M12 × 1
37.7
14.9 dia.
23
XS5G-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 7 or 8 mm)
Straight Connectors
M12 × 1
58.7
20 dia. 14.9 dia.
16 dia.
XS5G-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 3, 4, or 6 mm)
Straight Connectors
M12 × 1
58.7
20 dia. 14.9 dia.
XS5G-D@S@ (Screw-on Connectors)
Angled Connectors
M12 × 1
14 dia.
39.7
20 dia. 14.9 dia.
39.6
14 dia.
8
XS5
Ordering Information
No. of
poles
4
Connection
method
Suitable cable dia.
(mm)
Core conductor size
(mm2)
IDC
3 to 8 mm
6 mm (5 to 6)
0.14 to 0.75 *1
Crimping
4 mm (4 to 5)
3 mm (3 to 4)
6 mm (5 to 6)
Soldering
4 mm (4 to 5)
3 mm (3 to 4)
6 mm (5 to 6)
Screw-on
4 mm (4 to 5)
3 mm (3 to 4)
8 mm (7 to 8)
7 mm (6 to 7)
6 mm (5 to 6)
Suitable sheath
material
0.18 to 0.3
0.5 to 0.75 *2
0.5 max.
PVC, PE, PUR
0.18 to 0.75
Straight Connectors
Angled Connectors
Model
XS5G-D418
--XS5G-D4C1
--XS5G-D4C3
--XS5G-D4C5
--XS5G-D421
XS5G-D422
XS5G-D423
XS5G-D424
XS5G-D425
XS5G-D426
XS5G-D4S1
XS5G-D4S2
XS5G-D4S3
XS5G-D4S4
XS5G-D4S5
XS5G-D4S6
XS5G-D4S7
--XS5G-D4S9
--XS5G-D5S1
--XS5G-D5S3
--XS5G-D5S5
--XS5G-D5S7
--XS5G-D5S9
---
Minimum
order
50
4 mm (4 to 5)
3 mm (3 to 4)
8 mm (7 to 8)
7 mm (6 to 7)
*1. Minimum wire diameter: 0.08 mm, Outer diameter of wire covering: 0.7 to 2.6 mm, Material of wire covering: PVC and PE
*2. There are two types of contacts.
5
Screw-on
Note: XS5G Screw-on Plugs cannot be connected to side by side to the CN1 and CN2 connectors of XS2R or XS5R Y-Joint Sockets/Plugs.
Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.
9
XS5
XS5U (Crimping Pin for XS5G)
Dimensions
(Unit: mm)
XS5U-312@
Plug Pin
* A special tool must be used for crimping. For details, refer to page 18.
Dimensions
Slit
1 dia.
2 dia. 2.3 dia.
C dia.
1.5
B
Model
Suitable core Dimension (mm) No. of
size (mm2)
slits
A
B
C
XS5U-3121
0.18 to 0.3
22.6
6.1
0.8
1
XS5U-3122
0.5 to 0.75
22.7
6.2
1.3
0
A
Ordering Information
Suitable core size (mm2)
Model
0.18 to 0.3
XS5U-3121
0.5 to 0.75
XS5U-3122
Minimum order
100
Note: Orders are accepted in multiples of the minimum order.
10
XS5
XS5C Assembly Connector Sockets
Dimensions
(Unit: mm)
XS5C-D418 (IDC Model)
Straight Connectors
62.4
54.4
M12 × 1
17.5 dia. 14.9 dia.
XS5C-D4C@ (Crimping Model)
XS5C-D42@ (Soldering Model)
Straight Connectors
M12 × 1
14.9 dia.
14.2 dia.
43.4
XS5C-D4C@ (Crimping Model)
XS5C-D42@ (Soldering Model)
Angled Connectors
31.8
M12 × 1
14.9 dia.
23
XS5C-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 7 or 8 mm)
Straight Connectors
54.9
M12 × 1
20 dia. 14.9 dia.
16 dia.
XS5C-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 3, 4, or 6 mm)
Straight Connectors
M12 × 1
54.9
20 dia. 14.9 dia.
XS5C-D@S@ (Screw-on Connectors)
Angled Connectors
14 dia.
35.9
M12 × 1
20 dia. 14.9 dia.
39.6
14 dia.
11
XS5
Ordering Information
Straight Connectors
Angled Connectors
Model
IDC
3 to 8 mm
0.14 to 0.75 *1
XS5C-D418
--6 mm (5 to 6)
XS5C-D4C1
XS5C-D4C2
0.18 to 0.3
XS5C-D4C3
XS5C-D4C4
Crimping
4 mm (4 to 5)
0.5 to 0.752 *2
XS5C-D4C5
XS5C-D4C6
3 mm (3 to 4)
6 mm (5 to 6)
XS5C-D421
XS5C-D422
Soldering
0.5 max.
XS5C-D423
XS5C-D424
4 mm (4 to 5)
4
XS5C-D425
XS5C-D426
3 mm (3 to 4)
6 mm (5 to 6)
XS5C-D4S1
XS5C-D4S2
PVC, PE, PUR
XS5C-D4S3
XS5C-D4S4
4 mm (4 to 5)
Screw-on
XS5C-D4S5
XS5C-D4S6
3 mm (3 to 4)
XS5C-D4S7
--8 mm (7 to 8)
XS5C-D4S9
--7 mm (6 to 7)
0.18 to 0.75
6 mm (5 to 6)
XS5C-D5S1
--XS5C-D5S3
--4 mm (4 to 5)
5
Screw-on
XS5C-D5S5
--3 mm (3 to 4)
XS5C-D5S7
--8 mm (7 to 8)
XS5C-D5S9
--7 mm (6 to 7)
*1. Minimum wire diameter: 0.08 mm, Outer diameter of wire covering: 0.7 to 2.6 mm, Material of wire covering: PVC and PE
*2. There are two types of contacts.
No. of
poles
Connection
method
Suitable cable dia.
(mm)
Core conductor size
(mm2)
Suitable sheath
material
Minimum
order
50
Note: Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.
12
XS5
XS5U (Crimping Pin for XS5C)
Dimensions
(Unit: mm)
* A special tool must be used for crimping. For details, refer to page 18.
XS5U-222@
Socket Pin
Dimensions
Slit
C dia. 2 dia. 2.3 dia.
1.5
B
Dimension (mm) No. of
slits
A
B
C
Model
Suitable core
size (mm2)
XS5U-2221
0.18 to 0.3
16.7
6.1
0.8
1
XS5U-2222
0.5 to 0.75
16.8
6.2
1.3
0
A
Ordering Information
Suitable core size (mm2)
Model
0.18 to 0.3
XS5U-2221
0.5 to 0.75
XS5U-2222
Orders are accepted in multiples of the minimum order.
Minimum order
100
13
XS5
XS5R Y-Joint Plug/Socket Connectors
Dimensions
(Unit: mm)
XS5R-D426-@11-F
Connectors on Both Ends (Y-Joint Plug/Socket)
15.0
M12 × 1
Wiring Diagram
45.5
Socket
4.6 dia.
CN2
1
2
3
4
CN2
Plug
1 2
4 3
35.0
4
1
18.0
1 2
4 3
CN1
Blue marking
8.5
M12 × 1
44.7
13.6
4
3
2
1
3
2
1
2
3
4
CN1
L
XS5R-D426-@10-F
Connectors on One Cable End (Y-Joint Socket)
15.0
M12 × 1
Wiring Diagram
45.5
Socket
1
2
3
4
CN2
4.6 dia.
CN2
1 2
4 3
Black
Blue
White
18.0
35.0
1 2
4 3
CN1
8.5
CN1
13.6
Blue marking
Wiring Diagram
XS5R-D426-1
27
1 2
4 3
(37)
Socket
7
Brown
50
XS5R-D426-@
Y-Joint Plug/Socket without Cable
M12 × 1
5
30
L
15
1
2
3
4
CN2
4
3
2
1
CN1
4
3
2
1
4.5 dia.
CN2
CN0
XS5R-D426-5
CN2
4
3
2
1
CN1
4
3
2
1
Plug 24.5
4
3
2
1
18
2
1
4 3
12.5
CN1
58.3
4
3
2
1
CN0
CN0
M12 × 1
Blue marking
Ordering Information
Cable
Connector
Connectors on both cable
ends
With cable
Connector on one cable
end
Cable
With no cable
Connector
Y-Joint Plug/Socket
Cable length (m)
Model
0.5
XS5R-D426-B11-F
1
XS5R-D426-C11-F
2
XS5R-D426-D11-F
3
XS5R-D426-E11-F
2
XS5R-D426-D10-F
5
XS5R-D426-G10-F
Cable length (m)
—
Model
XS5R-D426-1
XS5R-D426-5
Minimum order
10
5
Minimum order
10
Note 1. Ask your OMRON representative about other specifications.
2. XS2G/XS5G Assembled Connectors with screw connections cannot be connected to both CN1 and CN2 at the same time.
14
XS5
XS5P Panel-mounting Sockets
Dimensions
(Unit: mm)
XS5P-D426-5
Rear-locking Socket Connected to Wires
17
M12×1
23
18
2.8
14
Wiring
18
PG9
500
White
Blue
Pin number
Color
1
Brown
2
White
20
14.6 dia.
20
10
2.5
Brown
Black
11.9
XS5P-D427-5
Front-locking Socket Connected to Wires
M12×1
2.8
PG9
Blue
4
Black
Wire Specifications
22.1
18
3
17
500
Blue
White
Item
Specification
Specification
UL1007
Nominal size
AWG20
Number of
wires
21
Wire diameter
0.18
Standard outer
diameter
1.8
2
3
21
1
Configuration
18
13.9 dia.
4
20
10
Brown
Black
2.5
10.5
22.1
XS5P-D526-4 Rear-locking Socket with Solder Cup Pins
XS5P-D426-4 Rear-locking Socket with Solder Cup Pins
17
18
2.8
M12×1
Nut
PG9
3.5
18
4, 1.3 dia.
17
2.8
M12×1
Nut
PG9 5.5
3.5
18
20
14.6 dia.
14.6 dia.
18
2.5
20
11.9
Resin filling
22.1
2.5
11.9
Resin filling
22.1
XS5P-D527-4 Front-locking Socket with Solder Cup Pins
XS5P-D427-4 Front-locking Socket with Solder Cup Pins
2.8
18
20
M12×1
5, 1.3 dia.
PG9
17
3.5
Nut
13.9 dia.
4, 1.3 dia.
18
10.5
2.5
22.1
18
2.8
M12×1
20
Nut
PG9
5.5
3.5
17
13.9 dia.
18
10.5
Resin filling
5, 1.3 dia.
2.5
Resin filling
22.1
Panel Cutout
+0.1
0 dia.
15.3
Panel Cutout Dimension
Panel thickness = 1 to 4 mm
Note 1. The panel cutout dimension is the same for Front-locking and Rear-locking Sockets.
2. Rotational positioning is not possible for connector rotation.
Ordering Information
Type
No. of poles
With cable
4
Type
No. of poles
Solder cup
pins
4
5
Lock
Rear lock
Front lock
Cable length (m)
Lock
Rear lock
Front lock
Rear lock
Front lock
Applicable wires
0.5
AWG20 to AWG28
Model
XS5P-D426-5
XS5P-D427-5
Minimum order
Model
XS5P-D426-4
XS5P-D427-4
XS5P-D526-4
XS5P-D527-4
Minimum order
10
50
15
XS5
XS5M Panel-mounting Plugs
Dimensions
(Unit: mm)
XS5M-D426-5
Rear-locking Plug Connected to Wires
18
2.8
M12×1
Wiring
18
PG9
Pin number
Color
1
Brown
2
White
Brown
500
White
1
4
17
20
2
3
20
10
2.8
Blue
Black
3
Blue
4
Black
10
Wire Specifications
22.8
XS5M-D427-5
Front-locking Plug Connected to Wires
18
M12×1
PG9
2.8
Item
18
500
White
Brown
Specification
UL1007
Nominal size
AWG20
1
4
20
17
2
20
10
Blue
Black
Number of wires
21
Wire diameter
0.18
Standard outer
diameter
1.8
Configuration
3
Specification
2.8
8
22.8
XS5M-D426-4 Rear-locking Plug with Solder Cup Pins
Nut
M12×1
18
2.8
XS5M-D526-4 Rear-locking Plug with Solder Cup Pins
PG9
3.5
18
17
2.8
Resin filling
18
4, 1.3 dia.
17
8
5, 1.3 dia.
Resin filling
2.8
Nut
5.5
3.5
18
5, 1.3 dia.
17
20
2.8
8
Resin filling
22.8
18
10
PG9
18
M12×1
20
5.5
3.5
XS5M-D527-4 Front-locking Plug with Solder Cup Pins
2.8
3.5
PG9
22.8
XS5M-D427-4 Front-locking Plug with Solder Cup Pins
Nut
M12×1 PG9
Nut
20
10
22.8
18
M12×1
17
20
2.8
2.8
18
4, 1.3 dia.
2.8
Resin filling
22.8
Panel Cutout
+0.1
0 dia.
15.3
Panel Cutout Dimension
Panel thickness = 1 to 4 mm
Note 1. The panel cutout dimension is the same for Front-locking and Rear-locking Sockets.
2. Rotational positioning is not possible for connector rotation.
Ordering Information
Type
No. of poles
With cable
4
Type
No. of poles
Solder cup
pins
4
5
Lock
Rear lock
Front lock
Cable length (m)
Lock
Rear lock
Front lock
Rear lock
Front lock
Applicable wires
0.5
AWG20 to AWG28
Model
XS5M-D426-5
XS5M-D427-5
Minimum order
Model
XS5M-D426-4
XS5M-D427-4
XS5M-D526-4
XS5M-D527-4
Minimum order
10
50
16
XS5
Connector Covers
Water-resistive Covers
XS2Z-11
XS2Z-11
M12 male screw
M12 × 1
XS5Z-11
Model
Minimum order
XS2Z-11
50
XS5Z-11
Dust Covers
XS2Z-13
The Water-resistive Cover ensures IP67.
When mounting the Water-resistive Cover
to a Connector, be sure to apply a torque
range between 0.39 and 0.49 N·m to
tighten the Water-resistive Cover.
XS5Z-11 is Smart click mechanism. There's
no need to keep track of locking torque.
M12 female screw
XS5Z-11
Suitable connector
Model
Mounting portion
XS5G/XS5H/XS5M/XS5R/XS5W/
Brass/nickel plated
M12 male screw
XS2G/XS2H/XS2M/XS2R/XS2W
PBT
XS5C/XS5F/XS5P/XS5R/XS5W/XW3D
M12 female screw
Material
XS2Z-13
M12 male screw
XS2Z-15/XS2Z-14
XS2Z-15
XS2Z-14
M12 female screw
Pin block (female pins)
Model
Minimum order
Material
XS2Z-13
XS2Z-14
50
Rubber/black
XS2Z-15
Sputter Protective Cover
XS2Z-31
XS2Z-31
The Dust Cover is for dust prevention and
does not ensure IP67 degree of protection.
When mounting the Dust Cover to a
connector, be sure to press the Dust Cover
onto the Connector until the Connector is
fully inserted into the Dust Cover.
Suitable connector
Mounting portion
Model
XS5G/XS5H/XS5M/XS5R/XS5W/
M12 male screw
XS2G/XS2H/XS2M/XS2R
XS5C/XS5F/XS5P/XS5R/XS5W/ Pin block (female pins)
XS2C/XS2F/XS2P/XS2R/XS2W/
M12 female screw
XW3B/XW3D
M12 female screw (thread bracket)
The Sputter Protective Cover protects the
connector from weld sputter.
Make sure it covers the entire connector.
Pin block (female contact)
Model
Material
XS2Z-31
Silicone rubber/black
Applicable connector
XS5F/XS5H/XS5W/
XS2F/XS2H/XS2W
17
XS5
Tools
Crimp Tool
Locator
XY2F-0002
XY2F-0003
Tool in open position
Tool in closed
position
3
R
1
4
PUSH POS
TATE 90 I
°
RO
TE
TA
IN
7
L
AL
ST
• The XY2F-0002 Crimp Tool is DMC's AFM8 (M22520/2-01).
• Mount the XY2F-0003 Locator (sold separately) to the locator
guide of the Crimp Tool with a screw provided with the XY2F-0003
Locator.
SE TO RO
AI
8
90° TO
Use the Crimp Tool to crimp a cable core to the XS5U or XS2U
Crimping Pin used with the XS@C or XS@G Crimping Connector.
SEL.
NO.
2
TE
TA
O
ER AND
ON INSTA R
LL
TI TO
6
5
Selector dial
(Set to 8.)
Locator guide
XY2F-0002
Crimp Tool
Model
XY2F-0003
Locator
XY2F-0002
XY2F-0003
Pin-block Extraction Tool
XY2F-0001
Use this tool to extract a Pin Block from the covers in order to make
wiring changes or corrections after the cover has been mounted to the
pin block for Connector Assemblies (XS@C/XS@G, soldering/
crimping).
Model
XY2F-0001
Extraction Procedure
(1) Disconnecting Components
• Disconnect all components on the cap side from the cover.
• Make sure that the pin block is outside the Tool.
Tool
Pin block
Pin block
Cover
Rubber
bushing
Cable
clamp
Cap
Cover
Guide
Cover
• Press the Tool so that the guides of the Tool are in close contact.
Then pull the pin block straight.
(2) Extracting Pin Block
• Insert the claws of the Tool into the four holes of the cover.
Guide
Pin block
Holes
Extracting
direction
Precaution for Safe Use
Claws
• The pin block must not be extracted from the same Connector
more than 3 times, otherwise the proper degree of protection of the
pin block or Connector will not be maintained.
18
XS5
Assembly Procedure for XS5C/XS5G (IDC models) Connector Assemblies
(1) Preparations (Make sure they are all at hand.)
(6) Processing the core wire end
• Cut the end part of each core wire with nippers. Cutting the
core wire end in the range of cut-area of figure.
Terminal number
indication surface
Cap
IDC cover
Contact block
Boss
Core wire
Cap unit
(2) Dressing the cable end
• Peel covering of a cable.
Cut-area
Note: Please be careful not to cut the boss.
approx. 40 mm
External diameter of
applicable cable
3 to 8 mm
Cable
Conductor cross section
0.14 to 0.75mm2 / AWG26 to 18
(7) Assembling the Contact block
• Insert the cap unit core wire end processing has completed
in a contact block.
• Use a mark of a housing and an arrow of a IDC cover, as
a guideline of alignment. The location of the arrow is the
side of the terminal No.1.
(3) Choose the waterproof bushing
• Choose the waterproof bushing type according to the cable
size.
<External diameter of cable: In case of 3 to 5 mm>
Use the cap unit in the delivery state.
Pink marking
Housing
<External diameter of cable: In case of 5 to 8 mm>
When using, pick tab both sides of the waterproof bushing
with a tab and pull it out in the direction of an arrow.
(Not required.)
waterproof bushing with a tab
* Color : Housing/ IDC cover
XS5C : Gray
XS5G : White
Note: Confirm that the color of the housing and the IDC cover is same before
insertion.
(8) Tightening up the cap
• After inserting the cap unit and tightening a screw up lightly
by hand, screw up the cap by a tool of a spanner or wrench
(size 15 mm).*2
Note: When it isn't necessary to pull out bushing, do not pull a tab or pull out
bushing carelessly. Do not insert the pulled-out bushing again.
(4) Cable insertion
• Insert a cable in the cap unit.
* Insert fully until a cable doesn't
enter any more.
* It's shown by a figure in case of
cable external diameter 3 to 5
mm.
(5) Wiring
• Confirm the terminal number indication*1 of a IDC
(Insulation Displacement Contact) cover, insert a core wire
in each wire guide according to the terminal number and
push in to the lowermost part of a core wire storage part.
*1. Terminal No.1: Brown
Terminal No.2: White
Terminal No.3: Blue
Terminal No.4: Black
Core wire storage part
Core wire
Note: There is a difference in a
storing state depending
on core wire diameter.
Wire guide part
completion position
*2. When screwing up the cap by large size tool,
it may cause damage.
• When a gap between a mold cover of contact block and a
cap disappeared assembly and wire connection has
completed.
Fixture
Mold cover
completion position
Note 1. When the operation has completed, mark of cap comes into the
square of the indicator formed into a mold cover (
), so also use
it as guideline to know to complete.
2. Avoid tightening a cap up beyond the completion position. It may cause
damage.
(9) Final checking
• When the connector has been assembled, make sure the
line insulation is as specified.
19
XS5
Repair work procedure
Cap unit removal
• When releasing wire connection, remove the cap unit in the
opposite procedure of assembly work. [ from (8) to (7) ]
Note 1. The core wire remain connected to the IDC connection part rarely. In
that case, remove core wire end part to the vertical direction by
tweezers etc. Do not touch the IDC contact directly at that time.
2. When IDC cover was left on the housing side, remove it by pulling a
cable. In case IDC cover has been removed by holding strongly and
pulling, it may cause damage.
Cable removal
• When removing the cable from the cap unit,
pull the cable to the opposite direction of
assembly work procedure (4). When tip of
the core wire end has been pushed lightly
into the IDC cover by tweezers etc, cable
removal becomes easy.
Repair work
• When connecting the wire again, do assembly (repair work)
according to assembling procedure from (1) to (8).
Note 1. In case of repair, use a cable of the same diameter and a core wire of
the same diameter. The number of times of repair wire connection is
maximum 10 times.
2. When doing a repair, work after enough removing the foreign substance
and moisture adhering to a connector. Be careful so that the foreign
substance and moisture do not enter the wire connection part. It may
cause short-circuit etc.
20
XS5
Assembly Procedure for XS5C/XS5G (Crimping/Soldering/Screw-on models)
Connector Assemblies
(1) Connector and Cable External Diameters
• Connectors for 8 ,7 ,6 , 4 , and 3 mm diameter Cables (i.e., Cables
that are 7 to 8, 6 to 7, 5 to 6, 4 to 5, and 3 to 4 mm in diameter
respectively) are available. When assembling a Connector used
with a cable, make sure that the external diameter of the Connector
is suited to that of the cable.
• A watertight bushing for 6/7 mm diameter Cable has no stripe, that
for 8/4 mm diameter Cable has a single stripe, and that for 3 mm
diameter Cable has two stripes.
Crimping/Soldering Connectors
Straight Connectors
Watertight Cable
bushing clamp
Soldering Connectors
4
6
6±0.5 *A
• Strip 10 mm of the Cable sheath and 4 mm of each core.
• Before soldering cores and solder cup pins together, solder-coat
each of them.
• The following conditions are recommended for soldering each
solder cup pin.
Soldering temperature: 350±5°C
Soldering period: 3±1 s
• The length marked *A should be 6.5 mm max., otherwise the
proper degree of protection of the connector will not be maintained.
(2) Component Insertion
Cover
(3) Wiring (Processing Cable Ends)
Cap
Crimping Connectors
Angled Connectors
Crimping
4
Ring (Angled models only) *
Watertight
bushing
Cover
Cable clamp
0
−4
Cap
* A ring is not required for Screw-on Connectors.
• As shown in the above illustration, connect the above components
to the Cable with its end processed.
Screw-on Connectors
Confirm that you have all of the required parts.
Cover
Watertight
bushing
10
Cable clamp
Cap
• Strip 14 mm of the Cable sheath and 4 mm of each core.
• Make sure that each core is not damaged and its end strands are
not spread out.
• Mount the XY2F-0003 Locator to XY2F-0002 Crimping Tool, both
of which are sold separately, and set the selector dial of the
Crimping Tool to 8.
• After mounting the crimping pins to the Locator, fully insert the
cores to the crimping pins.
• Squeeze the handle of the Crimp Tool to press-fit the cores to the
crimping pins.
(Squeeze the handle firmly until the handle automatically returns to
the release position.)
Wiring
(
*2
)
Pin clamp
Press
Ring *1 Watertight bushing
Cover
Cable clamp
Cap
Insulation caps and insulation tubes are included with
five-pole Connectors (XS2C-D5S@ and XS2G-D5S@).
1 to 1.5
• After press-fitting the cores to the pins, insert the pins into the pin
clamp as shown in the illustration. Then make sure that the lead
colors correspond to the pin clamp numbers that are identical to
the connector pin numbers.
*1. Rings are not required with 7-mm and 8-mm cables.
*2. Insert the waterproof bushing for 7-mm and 8-mm
cables in the direction shown in the diagram.
21
XS5
• Bend the cable as shown below, attached the enclosed insulation
cap, and then strip the other cores.
Insertion
Pin Block
Pin Clamp
Key groove Key groove
XS5C use XS5G use
Key
6±0.5
Insulation cap
• Tentatively insert the pins to the pin block holes so that the key on
the pin block will coincide with the key groove on the pin clamp.
Then insert the cable along with the pin clamp.
• Connect the cores to pins 1 to 4.
Connecting Shielded Cables to Five-pole Connectors
• Place the insulation tub on the drain line of the shield and connect
it to the terminal.
• Tighten the screw and then check visually to see if there is
insulation between the cores.
Screw-on Connectors
Cable End Processing
• Four-pole Connectors
Drain line
8
Insulation tube
12
12±0.5
• Loosen the screws on pins 1 to 4 and insert the cores according to
the pin numbers.
* When tightening the screws, use the dedicated XW4Z-00B
Screwdriver that matches with the screw-slot dimensions.
XW4Z-00B
Screwdriver
• Use the dedicated Screwdriver (XW4Z-00B)* and tighten the
screws securely so that the cores do not pull out (tightening torque:
0.15 to 0.2 N·m).
• Five-pole Connectors
• Strip the cable sheath for a total of 15 mm and strip the core
covering for 8 mm for the core to connect to pin 5.
8
12
Conductors for
pins 1 to 4
7
Conductors for
pin 5
(4) Inserting Pin Block
Pin Block
(Soldering Model)
Lock spring
Polarity key
8
(Crimping Model)
• Connect the core to pin 5 (in the center) first.
• Insert the core from the side of the hold with the tab and tighten the
screw securely (tightening torque: Pins1 to 4: 0.15 to 0.2 N·m,
Pins5: 0.03 to 0.05 N·m), and then cut off the excess wire with wire
cutters.
Screw
Screw
Dedicated
screwdriver
Dedicated
screwdriver
Tab
Cover
(Straight Model)
O-ring
Positioning key
(triangle mark)
Triangle mark
(Angled Model)
• Mount the cover to the pin block so that the triangle mark on the pin
block will coincide with the triangle mark on the cover.
• If the cover is used for an Angled model, the relationship between
the position of the polarity key on the engaged side and cable
connection direction will be determined by the direction in which
the positioning key is inserted into the cover, which can be rotated
by 90°.
• Fully insert the positioning key until the positioning key is hidden by
the casing.
22
XS5
Connecting the XS5
1. Connecting the XS5 Plug and Socket
Pin Block
(Screw-on Connectors)
• Align the projection on the plug cover with the polarity key on the
socket, then insert the plug all the way in.
Cover
Triangle mark
Polarity key Protrusion on
cover aligns with
polarity key.
Cover lock
Pin block
• Align the triangular marks on the pin block and cover and insert the
pin block into the cover.
• Press them together firmly (0.39 to 0.49 N·m) until the pin block
does not come out of the cover.
• Hold the knurled socket grip, then insert the projection on the plug
into the groove of the socket.
(5) Mounting Cap
• After mounting the cover to the pin block and the cover snaps into
place, tighten the cap securely by hand within a torque of 0.39 and
0.49 N·m.
Note: If the cap is not tighten securely enough, the degree of
protection (IP67) may not be maintained or vibration may
cause the cap to become loose. Do not tighten the cap with
pliers or similar tools; they may damage the cap.
A
• Turn the knurled grips of the socket clockwise approximately 45
degrees in respect to the plug. A click will indicate that the
Connectors are locked. The locking condition can also be
confirmed by the alignment marks on the plug and socket.
Cap
Alignment marks
• After fully tightening the cap, length A should be approximately one
of the following according to the cable external diameter and the
Connector model.
Cable external diameter (mm)
Connector
6 mm
5 mm
4 mm
For 6-mm-dia. cable
1
0
---
3 mm
---
For 4-mm-dia. cable
---
2
1
---
For 3-mm-dia. cable
---
---
2
1
2. Connecting the XS5 and XS2
• Align the projection on the plug cover with the polarity key on the
socket, then insert the plug all the way in.
• In the same way as when connecting two XS2 Connectors, screw
the knurled grip in the clockwise direction.
• Use your fingers to tighten the Connectors sufficiently.
(6) After Assembly
• Confirm the insulation between cores after completing assembly.
Recommended Cables
When connecting a commercially available cable to a connector
assembly, use a cable with an outside diameter of 3 to 6 mm and core
sizes of 0.18 to 0.75 mm2 for crimping connectors and 0.5 mm2
maximum for soldering connectors.
Connector Arrangement
For safety, when constructing a connection system between a Sensor
and panel with a connector, make sure that the connector plug is on
the Sensor side and the connector socket is on the panel side (i.e.,
the female pins are located on the power-supply side).
Sensor Side
(Plug)
Connecting Cable
(Socket)
(Plug)
Panel Side
(Power-supply Side)
(Socket)
23
XS5
Safety Precautions
Precautions for Correct Use
Do not use the Connectors in an atmosphere or environment that
exceeds the specifications.
Connector Connection and Disconnection
• When connecting or disconnecting Connectors, be sure to hold the
Connectors by hand.
• Do not hold the cable when disconnecting Connectors.
• When mating Connectors, be sure to insert the plug all the way to
the back of the socket before attempting to lock the Connectors.
• Do not use tools of any sort to mate the Connectors. Always use
your hands. Pliers or other tools may damage the Connectors.
• When mating the Connectors to XS2 or other M12 Connectors,
tighten the lock by hand to a torque of 0.39 to 0.49 N⋅m.
Wiring
• Always confirm wiring diagrams before wiring sensors, limit
switches, or other devices.
• Lay the cables so that external force is not applied to the
Connectors. Otherwise, the degree of protection (IP67) may not be
achieved.
General Precautions
• Do not pull excessively on the Connectors or cables. Do not install
the Connectors or cables in any way that would place a load
directly on the mating section or cable connections. Doing so can
damage the Connectors or break the wires inside the cables.
• Install the Connectors and cables where they will not be stepped
on to prevent the wires inside the cables from being broken and to
prevent the Connectors from being damaged. If the Connectors or
cables must be installed where they might be stepped on, protect
them with covers.
• Refer to the specifications for your cables before bending the
cables and do not bend them past their minimum bending radius.
• If sensors or switches are not attached during installation, protect
the mating surface of the Connector with a XS5Z-11 Waterproof
Cover of XS2Z-14/15 Dust Cover.
Setup
• Do not make any cable bends near the base of the Unit.
• Any bends made must have a minimum radius of 40 mm.
Degree of Protection
• The degree of protection of Connectors (IP67) is not for a fully
watertight structure. Do not the Connectors underwater.
• Do not step on or place any objects on the Connectors. Doing so
may damage the Connectors.
24
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2016.3
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2016 All Right Reserved.