Download

N EW
Read and Understand this Catalog
Easy to use
Standard type for a fan type ionizer with high performance
Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any questions or comments.
Slim & Light
Fan Ionizer
ZJ-FW Series
ZJ-FA20
Warranty and Limitations of Liability
WARRANTY
Area fan type ionizer that can fit anywhere
LIMITATIONS OF LIABILITY
OMRON's exclusive warranty is that the products are free from defects in
materials and workmanship for a period of one year (or other period if
specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR
IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER
OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE
REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL
LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER
SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR
STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the
individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY,
REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
ZJ-FW053
530mm
59.5mm
A new concept
from the production floor.
70mm
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes,
or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party
certification documents identifying ratings and limitations of use that apply to
the products. This information by itself is not sufficient for a complete
determination of the suitability of the products in combination with the end
product, machine, system, or other application or use.
The following are some examples of applications for which particular
attention must be given. This is not intended to be an exhaustive list of all
possible uses of the products, nor is it intended to imply that the uses listed
may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems,
aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or
government regulations.
ZJ-FW013
130mm
ZJ-FW029
• Systems, machines, and equipment that could present a risk to life or
property.
290mm
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Basic fan type
ZJ-FA20
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a
programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
PERFORMANCE DATA
Product specifications and accessories may be changed at any time based
on improvements and other reasons.
Basic fan type
ZJ - FA20
Pick me up,
when you are not
sure that what
kind of fan ionizer
should be used!
This is the standard for a fan type
ionizer, which is easy-to-use and
has high performance.
Various installation
styles are
available to match
the workplace.
It is our practice to change model numbers when published ratings or
features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any
notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please
consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
Performance data given in this catalog is provided as a guide for the user in
determining suitability and does not constitute a warranty. It may represent
the result of OMRON’s test conditions, and the users must correlate it to
actual application requirements. Actual performance is subject to the
OMRON Warranty and Limitations of Liability.
Area fan type
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed
to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
Slim,
lightweight body
3 types
to choose
from by
area coverage
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for
manufacturing purposes, even when tolerances are shown.
6 cm thick
Just
1kg in weight
*
ZJ-FW Series
This ionizer series is designed to go anywhere.
All models are easily installed on narrow
workbenches or in high positions where earlier
models presented installation issues.
* ZJ-FW029
Ionization area vs. Ionization time
OMRON Corporation
2.5
300
Ionization time (s)
Airflow level 1
200
2.0
3
4
1.0
Contact: www.ia.omron.com
3s 4s
1s 2s
Regional Headquarters
0
MAX:5
-100
0.5
0
0.5
0.8
1.0
1.3
Airflow (m/s)
1.5
1.8
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
-200
-300
(mm) 0
Authorized Distributor:
Area fan type
Airflow vs. Ionization time
ZJ-FW Series
2.5
Tokyo, JAPAN
100
2
1.5
Industrial Automation Company
NEW
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
Ionization time (s)
Airflow vs. Ionization time
OMRON EUROPE B.V.
Sensor Business Unit
OMRON ELECTRONICS LLC
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
IL 60173-5302 U.S.A.
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
OMRON (CHINA) CO., LTD.
© OMRON Corporation 2012
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Room 2211, Bank of China Tower,
In the interest of product improvement,
Alexandra Technopark,
200 Yin Cheng Zhong Road,
specifications are subject to change without notice.
Singapore 119967
PuDong New Area, Shanghai, 200120, China
Tel: (65) 6835-3011/Fax: (65) 6835-2711
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
One Commerce Drive Schaumburg,
Airflow level 1
FW013
2.0
Cat. No. E420-E1-01
0112 (0112)
0
FW029
FW053
1
1.5
ZJ-FW053
300
300
200
1s 2s 3s 4s 5s
100
1s
2s
3s 4s 5s
100
1s
2s 3s
4s
5s
200
100
2
3
4
0
0
0
4
-100
-100
-100
-200
-200
-200
-300
(mm) 0
-300
(mm) 0
0.5
All Rights Reserved.
ZJ-FW029
300
3
1
1.0
ZJ-FW013
200
2
1.5
Ionization area vs. Ionization time
2
2.5
Airflow (m/s)
3
3.5
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
-300
(mm) 0
200 400 600 800 1000 1200 1400
Distance
(mm)
N EW
Read and Understand this Catalog
Easy to use
Standard type for a fan type ionizer with high performance
Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any questions or comments.
Slim & Light
Fan Ionizer
ZJ-FW Series
ZJ-FA20
Area fan type ionizer that can fit anywhere
Warranty and Limitations of Liability
WARRANTY
LIMITATIONS OF LIABILITY
OMRON's exclusive warranty is that the products are free from defects in
materials and workmanship for a period of one year (or other period if
specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR
IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER
OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE
REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL
LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER
SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR
STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the
individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY,
REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
ZJ-FW053
530mm
A new concept
from the production floor.
59.5mm
70mm
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes,
or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party
certification documents identifying ratings and limitations of use that apply to
the products. This information by itself is not sufficient for a complete
determination of the suitability of the products in combination with the end
product, machine, system, or other application or use.
The following are some examples of applications for which particular
attention must be given. This is not intended to be an exhaustive list of all
possible uses of the products, nor is it intended to imply that the uses listed
may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems,
aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or
government regulations.
ZJ-FW013
130mm
ZJ-FW029
• Systems, machines, and equipment that could present a risk to life or
property.
290mm
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Basic fan type
ZJ-FA20
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a
programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
PERFORMANCE DATA
Product specifications and accessories may be changed at any time based
on improvements and other reasons.
Basic fan type
ZJ - FA20
Pick me up,
when you are not
sure that what
kind of fan ionizer
should be used!
This is the standard for a fan type
ionizer, which is easy-to-use and
has high performance.
Various installation
styles are
available to match
the workplace.
It is our practice to change model numbers when published ratings or
features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any
notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please
consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
Performance data given in this catalog is provided as a guide for the user in
determining suitability and does not constitute a warranty. It may represent
the result of OMRON’s test conditions, and the users must correlate it to
actual application requirements. Actual performance is subject to the
OMRON Warranty and Limitations of Liability.
Area fan type
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed
to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
Slim,
lightweight body
3 types
to choose
from by
area coverage
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for
manufacturing purposes, even when tolerances are shown.
6 cm thick
Just
1kg in weight
*
ZJ-FW Series
This ionizer series is designed to go anywhere.
All models are easily installed on narrow
workbenches or in high positions where earlier
models presented installation issues.
* ZJ-FW029
Ionization area vs. Ionization time
OMRON Corporation
2.5
300
Ionization time (s)
Airflow level 1
200
2.0
3
4
1.0
Contact: www.ia.omron.com
3s 4s
1s 2s
Regional Headquarters
0
MAX:5
-100
0.5
0
0.5
0.8
1.0
1.3
Airflow (m/s)
1.5
1.8
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
-200
-300
(mm) 0
Authorized Distributor:
Area fan type
Airflow vs. Ionization time
ZJ-FW Series
2.5
Tokyo, JAPAN
100
2
1.5
Industrial Automation Company
NEW
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
Ionization time (s)
Airflow vs. Ionization time
OMRON EUROPE B.V.
Sensor Business Unit
OMRON ELECTRONICS LLC
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
IL 60173-5302 U.S.A.
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
OMRON (CHINA) CO., LTD.
© OMRON Corporation 2012
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Room 2211, Bank of China Tower,
In the interest of product improvement,
Alexandra Technopark,
200 Yin Cheng Zhong Road,
specifications are subject to change without notice.
Singapore 119967
PuDong New Area, Shanghai, 200120, China
Tel: (65) 6835-3011/Fax: (65) 6835-2711
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
One Commerce Drive Schaumburg,
Airflow level 1
FW013
2.0
Cat. No. E420-E1-01
0112 (0112)
0
FW029
FW053
1
1.5
ZJ-FW053
300
300
200
1s 2s 3s 4s 5s
100
1s
2s
3s 4s 5s
100
1s
2s 3s
4s
5s
200
100
2
3
4
0
0
0
4
-100
-100
-100
-200
-200
-200
-300
(mm) 0
-300
(mm) 0
0.5
All Rights Reserved.
ZJ-FW029
300
3
1
1.0
ZJ-FW013
200
2
1.5
Ionization area vs. Ionization time
2
2.5
Airflow (m/s)
3
3.5
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
-300
(mm) 0
200 400 600 800 1000 1200 1400
Distance
(mm)
N EW
Read and Understand this Catalog
Easy to use
Standard type for a fan type ionizer with high performance
Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any questions or comments.
Slim & Light
Fan Ionizer
ZJ-FW Series
ZJ-FA20
Area fan type ionizer that can fit anywhere
Warranty and Limitations of Liability
WARRANTY
LIMITATIONS OF LIABILITY
OMRON's exclusive warranty is that the products are free from defects in
materials and workmanship for a period of one year (or other period if
specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR
IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER
OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE
REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL
LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER
SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR
STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the
individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY,
REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
ZJ-FW053
530mm
A new concept
from the production floor.
59.5mm
70mm
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes,
or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party
certification documents identifying ratings and limitations of use that apply to
the products. This information by itself is not sufficient for a complete
determination of the suitability of the products in combination with the end
product, machine, system, or other application or use.
The following are some examples of applications for which particular
attention must be given. This is not intended to be an exhaustive list of all
possible uses of the products, nor is it intended to imply that the uses listed
may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems,
aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or
government regulations.
ZJ-FW013
130mm
ZJ-FW029
• Systems, machines, and equipment that could present a risk to life or
property.
290mm
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Basic fan type
ZJ-FA20
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a
programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
PERFORMANCE DATA
Product specifications and accessories may be changed at any time based
on improvements and other reasons.
Basic fan type
ZJ - FA20
Pick me up,
when you are not
sure that what
kind of fan ionizer
should be used!
This is the standard for a fan type
ionizer, which is easy-to-use and
has high performance.
Various installation
styles are
available to match
the workplace.
It is our practice to change model numbers when published ratings or
features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any
notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please
consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
Performance data given in this catalog is provided as a guide for the user in
determining suitability and does not constitute a warranty. It may represent
the result of OMRON’s test conditions, and the users must correlate it to
actual application requirements. Actual performance is subject to the
OMRON Warranty and Limitations of Liability.
Area fan type
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed
to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
Slim,
lightweight body
3 types
to choose
from by
area coverage
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for
manufacturing purposes, even when tolerances are shown.
6 cm thick
Just
1kg in weight
*
ZJ-FW Series
This ionizer series is designed to go anywhere.
All models are easily installed on narrow
workbenches or in high positions where earlier
models presented installation issues.
* ZJ-FW029
Ionization area vs. Ionization time
OMRON Corporation
2.5
300
Ionization time (s)
Airflow level 1
200
2.0
3
4
1.0
Contact: www.ia.omron.com
3s 4s
1s 2s
Regional Headquarters
0
MAX:5
-100
0.5
0
0.5
0.8
1.0
1.3
Airflow (m/s)
1.5
1.8
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
-200
-300
(mm) 0
Authorized Distributor:
Area fan type
Airflow vs. Ionization time
ZJ-FW Series
2.5
Tokyo, JAPAN
100
2
1.5
Industrial Automation Company
NEW
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
Ionization time (s)
Airflow vs. Ionization time
OMRON EUROPE B.V.
Sensor Business Unit
OMRON ELECTRONICS LLC
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
IL 60173-5302 U.S.A.
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
OMRON (CHINA) CO., LTD.
© OMRON Corporation 2012
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Room 2211, Bank of China Tower,
In the interest of product improvement,
Alexandra Technopark,
200 Yin Cheng Zhong Road,
specifications are subject to change without notice.
Singapore 119967
PuDong New Area, Shanghai, 200120, China
Tel: (65) 6835-3011/Fax: (65) 6835-2711
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
One Commerce Drive Schaumburg,
Airflow level 1
FW013
2.0
Cat. No. E420-E1-01
0112 (0112)
0
FW029
FW053
1
1.5
ZJ-FW053
300
300
200
1s 2s 3s 4s 5s
100
1s
2s
3s 4s 5s
100
1s
2s 3s
4s
5s
200
100
2
3
4
0
0
0
4
-100
-100
-100
-200
-200
-200
-300
(mm) 0
-300
(mm) 0
0.5
All Rights Reserved.
ZJ-FW029
300
3
1
1.0
ZJ-FW013
200
2
1.5
Ionization area vs. Ionization time
2
2.5
Airflow (m/s)
3
3.5
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
-300
(mm) 0
200 400 600 800 1000 1200 1400
Distance
(mm)
Area fan type
Basic fan type
ZJ-FW Series
ZJ-FA20
Ionization time
ZJ-FW029/053
ZJ-FW013
1.0 s 1.5 s
Ion balance
ZJ-FW013
± 10 V
Discharge method
Variable DC
(See “Ionization performance” of the ZJ-FA20.)
ZJ-FW029
Ionization performance
Reliability
High speed ionization
in a slim configuration
Ionization time
Ion generation understood
at a glance by LED lighting
1.2 s
A proprietary louver structure enables a slim configuration
and yet high speed ionization that removes electrostatic
charge in 1 sec or less. As a standard feature, ion balance
adjustment is available and airflow can be set by 4-step
sliding switch. Moreover, when using the standard stand, the
angle can be easily adjusted against a graduated scale.
Ion balance
During ion generation, both the POWER and ION
lamps are lit. This verifies that the ionizer is running
properly. Moreover, a CLEANING lamp notifies users
when it is time to clean the electrode needles.
± 10 V
Ion balance adjustor (Body rear)
Discharge method
Easy angle adjustment with
graduated scale
Variable DC
Cleaning lamp
Ion generation lamp
Power lamp
Reliability
3 slim, lightweight types to choose from.
Four indicators and
an alarm output
let you easily identify
the operating status.
At 6 cm in depth and weighing 1 kg (ZJ-FW029), the ZJ-FW Series has pursued and achieved a slim,
lightweight configuration. These ionizers easily fit on narrow workbenches or in high locations where
previously they could not go. Moreover, you can select a size according to the area of coverage, so
targets are uniformly neutralized.
The Ionizer’s operating status is displayed on easy-to-see
indicators and it can be output to an external device.
Besides the power (PWR) indicator, there are a CLEAN lamp
that lights when it is time for electrode needle maintenance,
an ALM lamp that lights if trouble occurs, and a FAN lamp
that is lit while the fan is operating.
ZJ-FW053
Easy installation.
High speed ionization and technological
sophistication at a reasonable price.
Excellent cost-performance.
Power lamp
Fan running lamp
Alarm lamp
Maintainability
Running status is understood at a glance.
Airblow sticker included
Cleaning notification lamp
Easy to clean and
replace electrode needles
Cleaning is easy and thorough owing to a full-open
structure that allows users to detach the front cover
by just pressing on tabs. Electrode needles can also
be easily replaced, which enables long lasting use of
the product.
The ZJ-FA20 delivers technological sophistication at a low price, featuring high speed ionization
that removes electrostatic charge in 1.2 s, ion balance control via a built-in sensor,
and a full-open structure that makes it easy to clean and replace electrodes.
Electrode cleaning
Variable DC ionization
Input/output circuit
Input and Output logic
Model
0V
* ZJ-FW013: 1 set, ZJ-FW029: 3 sets, ZJ-FW053: 6 sets
Rating/ Performance
ZJ-FW053
External output is ON(Close) state when ZJ-FW is working normally.
External output is OFF(Open) state as one of the below conditions occurs.
Front cover open, Cleaning, Fan rotation error, Malfunction error and Discharge stop input ON
1s
1.5 s
±10V max.
Ion balance *
Outer dimensions ZJ-FW013 (Units: mm)
0.01 ppm (Measured at a distance of 50 mm from air outlet)
Amount of ozone generated
Power (Green), Fan running (Green), Cleaning (Yellow), Alarm (Red)
Indicators
Ion balance adjustment (Automatic and manual)
Main functions
23
4.5
Photo MOS relay output (NPN or PNP)
External output
(for both cleaning
and alarm outputs)
2
20
• Applied voltage: 30VDC max., load current: 100mA max.
• Residual voltage: 1V max
No-voltage contact input
• ON: 0V short circuit
• OFF: Open (leakage current: 0.1mA max.)
0 to 50 ˚C (No icing or dewing)
Ambient humidity range
Weight (Packaged)
35% to 65% (No icing or dewing)
Approx. 0.6 kg (Approx. 1.2 kg)
Material
Accessories
Approx. 1 kg (Approx. 1.8 kg)
Body:Aluminum, ABS
Instruction sheet, I/O connector, L-mounting bracket, Streamer
130
Electrode needle: Tungsten
Instruction sheet, I/O connector, Stand, Streamer
* Typical default settings at the time of shipping from the factory
• Measurement conditions Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
59.5
Approx. 2 kg (Approx. 3 kg)
224.4
ZJ-FW029
A
345.4
Dimensions
B
C
336.4
290
D
360.4
ZJ-FW053
585.4
576.4
600.4
B
C
45°
59.5
60
Rotation range
ZJ-FA20
The ionizer can be used in a variety of postures. It can
be installed on a workbench or mounted on a pole.
It can also be freely angled using the angle adjustment
knob on the body and the screw slots on the stand.
Ion balance sensor
Dispersed airflow
D
45°
530
45°
Replacement filter (10-pack)
ZJ9-FL120N1
Replacement discharge electrode ( 6-pack)
ZJ9-NDT06FN1
60°
60°
3-5.5 dia.
Mounting hole dimensions
100 dia.
8.5
80
120°
12
ZJ-FA20
900 mA max. (When input by included AC adapter)
Vertical positioning
Left-Right swiveling
75
5.5 50 dia.
197.5
140
Current consumption
60°
7-M5
5.5
Discharge voltage
±7kV
50±0.2
Discharge method
Variable DC
15±0.2
Ionization time *2
1.2 s ( 0.8 s when used without filter )
Ion balance *2
Amount of ozone generated
Indicators
Main functions
Material
Accessories
±10 V max.
0.01 ppm (Measured at a distance of 50 mm from air outlet )
High voltage output: ION ( Yellow), Cleaning: CLEANING (Orange ), Power: POWER ( Green)
60°
Rotation Range
Ion balance adjustment (Automatic and manual ), airflow adjustment
Working and storage: 0 to 50˚C (No icing or dewing )
Working: 35% to 65%, Storage: 35% to 85% ( No icing or dewing )
Approx. 1.5 kg ( Approx. 2 kg)
Body: ABS, Electrode needle: Tungsten, Stand: SPCC
Instruction sheet, AC adapter, Warning label ( 2 types), FG connection cable ( 2 m)
*1 Use the ionizer only with the included AC adapter.
• Measurement conditions/Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
*2 Typical default settings at time of shipping from the factory
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
Rotation range
ZJ-FA20 ( Units: mm)
Model
24V DC *1
Ambient humidity range
Weight (Packaged)
79.5
Front-Back tilting
Channeled uniform airflow
Outer dimensions
Accessory
Power supply voltage
Ambient temperature range
45°
45°
Ambient temperature range
ZJ-FW029/053 ( Units: mm)
Model
182
70
67.5
95
Discharge stop input
Conventional ionizer
Item
A
188.4
Omron’s proprietary louver structure
Rating/ Performance
45°
Variable DC
ZJ-FA20
Various installation styles
are available according to
workplace
Approx. -5 kV-
Accessories
Model
45°
±7.5kV
Discharge method
Model
(2) External output
25
ZJ-FW Series
Discharge voltage
Ionization time *
3.0A max
1.2A max
ON (Closed)
OFF (Open)
120
0.9A max
When the discharge stop input is turned ON, the discharge from needles and rotation of fans stops
and external output turns OFF(Open).
External
output
di
a.
ZJ-FW029
24V DC±10%, Ripple (p-p): 10%
[External output]
ON
OFF
.5
ZJ-FW013
Power supply voltage
[Discharge stop input ]
(1) Discharge stop input
Discharge
stop input
44
ZJ9-BRP1FW
65
ZJ9-BRL1FW
Pipe-mounting bracket
Normal operation
70
L-mounting bracket
Operating state Power OFF
IN
85
127.5
155
ZJ9-BRS1FW
At an error, cleaning or
Front cover open
4.5
ZJ9-NDT04FW
Stand
60
Replacement discharge electrode (4-electrode set)*
ZJ-FW053
Load
-R
2.
25
ZJ-FW029
24V
45
ZJ9-FL40FW
45°
Replacement filter ( 6-pack )
10
ZJ-FW013
4.5
Accessory
Current consumption
Full-open structure for easy cleaning
Installation
165
80
120°
ZJ-FA20
(Stand, L-mounting bracket and pipe-mounting bracket available.)
Accessories
Item
Easy electrode needle replacement
0V
220
Easily installs in places where not applicable before!
The variable DC ionizer simultaneously
generates a large quantity of ions from
separate positive and negative electrode
needles, while a built-in ion balance sensor
controls ion quantity. The result is a good
balance between high speed ionization and
proper ion balance. Moreover, Omron’s
proprietary louver structure efficiently directs
ions to the target.
0V
200
Ionizer with pipe-mounting brackets
The ionizer adopts a full-open structure that allows users to detach
the front cover by just pressing on tabs. This makes electrode
needle cleaning very easy. Moreover, the electrode needles are
configured as a unit that can be easily and safely replaced.
Approx. +5 kV-
149
Easy electrode needle replacement
owing to modular structure
With three sizes available, the ideal ionizer for the installation
environment and ionization area can be selected. Stable
uniform ionization is possible for any kind of work setup from
narrow workbenches to wide lines. Moreover, tedious-to-rig
air ducts used with bar type ionizers are unnecessary, which
also translates into greater energy savings.
Model
High speed ionization by delivering
a high density ion flow on an
efficiently channeled air stream
Electrode replacement
Full-open structure
Variable DC ionization
120
Maintainability
Ideal for narrow
workbenches to wide lines
Model
Ionization performance
4
Easy installation
General DC ionization
Area fan type
Basic fan type
ZJ-FW Series
ZJ-FA20
Ionization time
ZJ-FW029/053
ZJ-FW013
1.0 s 1.5 s
Ion balance
ZJ-FW013
± 10 V
Discharge method
Variable DC
(See “Ionization performance” of the ZJ-FA20.)
ZJ-FW029
Ionization performance
Reliability
High speed ionization
in a slim configuration
Ionization time
Ion generation understood
at a glance by LED lighting
1.2 s
A proprietary louver structure enables a slim configuration
and yet high speed ionization that removes electrostatic
charge in 1 sec or less. As a standard feature, ion balance
adjustment is available and airflow can be set by 4-step
sliding switch. Moreover, when using the standard stand, the
angle can be easily adjusted against a graduated scale.
Ion balance
During ion generation, both the POWER and ION
lamps are lit. This verifies that the ionizer is running
properly. Moreover, a CLEANING lamp notifies users
when it is time to clean the electrode needles.
± 10 V
Ion balance adjustor (Body rear)
Discharge method
Easy angle adjustment with
graduated scale
Variable DC
Cleaning lamp
Ion generation lamp
Power lamp
Reliability
3 slim, lightweight types to choose from.
Four indicators and
an alarm output
let you easily identify
the operating status.
At 6 cm in depth and weighing 1 kg (ZJ-FW029), the ZJ-FW Series has pursued and achieved a slim,
lightweight configuration. These ionizers easily fit on narrow workbenches or in high locations where
previously they could not go. Moreover, you can select a size according to the area of coverage, so
targets are uniformly neutralized.
The Ionizer’s operating status is displayed on easy-to-see
indicators and it can be output to an external device.
Besides the power (PWR) indicator, there are a CLEAN lamp
that lights when it is time for electrode needle maintenance,
an ALM lamp that lights if trouble occurs, and a FAN lamp
that is lit while the fan is operating.
ZJ-FW053
Easy installation.
High speed ionization and technological
sophistication at a reasonable price.
Excellent cost-performance.
Power lamp
Fan running lamp
Alarm lamp
Maintainability
Running status is understood at a glance.
Airblow sticker included
Cleaning notification lamp
Easy to clean and
replace electrode needles
Cleaning is easy and thorough owing to a full-open
structure that allows users to detach the front cover
by just pressing on tabs. Electrode needles can also
be easily replaced, which enables long lasting use of
the product.
The ZJ-FA20 delivers technological sophistication at a low price, featuring high speed ionization
that removes electrostatic charge in 1.2 s, ion balance control via a built-in sensor,
and a full-open structure that makes it easy to clean and replace electrodes.
Electrode cleaning
Variable DC ionization
Input/output circuit
Input and Output logic
Model
0V
* ZJ-FW013: 1 set, ZJ-FW029: 3 sets, ZJ-FW053: 6 sets
Rating/ Performance
ZJ-FW053
External output is ON(Close) state when ZJ-FW is working normally.
External output is OFF(Open) state as one of the below conditions occurs.
Front cover open, Cleaning, Fan rotation error, Malfunction error and Discharge stop input ON
1s
1.5 s
±10V max.
Ion balance *
Outer dimensions ZJ-FW013 (Units: mm)
0.01 ppm (Measured at a distance of 50 mm from air outlet)
Amount of ozone generated
Power (Green), Fan running (Green), Cleaning (Yellow), Alarm (Red)
Indicators
Ion balance adjustment (Automatic and manual)
Main functions
23
4.5
Photo MOS relay output (NPN or PNP)
External output
(for both cleaning
and alarm outputs)
2
20
• Applied voltage: 30VDC max., load current: 100mA max.
• Residual voltage: 1V max
No-voltage contact input
• ON: 0V short circuit
• OFF: Open (leakage current: 0.1mA max.)
0 to 50 ˚C (No icing or dewing)
Ambient humidity range
Weight (Packaged)
35% to 65% (No icing or dewing)
Approx. 0.6 kg (Approx. 1.2 kg)
Material
Accessories
Approx. 1 kg (Approx. 1.8 kg)
Body:Aluminum, ABS
Instruction sheet, I/O connector, L-mounting bracket, Streamer
130
Electrode needle: Tungsten
Instruction sheet, I/O connector, Stand, Streamer
* Typical default settings at the time of shipping from the factory
• Measurement conditions Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
59.5
Approx. 2 kg (Approx. 3 kg)
224.4
ZJ-FW029
A
345.4
Dimensions
B
C
336.4
290
D
360.4
ZJ-FW053
585.4
576.4
600.4
B
C
45°
59.5
60
Rotation range
ZJ-FA20
The ionizer can be used in a variety of postures. It can
be installed on a workbench or mounted on a pole.
It can also be freely angled using the angle adjustment
knob on the body and the screw slots on the stand.
Ion balance sensor
Dispersed airflow
D
45°
530
45°
Replacement filter (10-pack)
ZJ9-FL120N1
Replacement discharge electrode ( 6-pack)
ZJ9-NDT06FN1
60°
60°
3-5.5 dia.
Mounting hole dimensions
100 dia.
8.5
80
120°
12
ZJ-FA20
900 mA max. (When input by included AC adapter)
Vertical positioning
Left-Right swiveling
75
5.5 50 dia.
197.5
140
Current consumption
60°
7-M5
5.5
Discharge voltage
±7kV
50±0.2
Discharge method
Variable DC
15±0.2
Ionization time *2
1.2 s ( 0.8 s when used without filter )
Ion balance *2
Amount of ozone generated
Indicators
Main functions
Material
Accessories
±10 V max.
0.01 ppm (Measured at a distance of 50 mm from air outlet )
High voltage output: ION ( Yellow), Cleaning: CLEANING (Orange ), Power: POWER ( Green)
60°
Ion balance adjustment (Automatic and manual ), airflow adjustment
Working and storage: 0 to 50˚C (No icing or dewing )
Working: 35% to 65%, Storage: 35% to 85% ( No icing or dewing )
Approx. 1.5 kg ( Approx. 2 kg)
Body: ABS, Electrode needle: Tungsten, Stand: SPCC
Instruction sheet, AC adapter, Warning label ( 2 types), FG connection cable ( 2 m)
*1 Use the ionizer only with the included AC adapter.
• Measurement conditions/Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
*2 Typical default settings at time of shipping from the factory
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
Rotation range
ZJ-FA20 ( Units: mm)
Model
24V DC *1
Ambient humidity range
Weight (Packaged)
79.5
Front-Back tilting
Channeled uniform airflow
Outer dimensions
Accessory
Power supply voltage
Ambient temperature range
45°
45°
Ambient temperature range
ZJ-FW029/053 ( Units: mm)
Model
182
70
67.5
95
Discharge stop input
Conventional ionizer
Item
A
188.4
Omron’s proprietary louver structure
Rating/ Performance
45°
Variable DC
ZJ-FA20
Various installation styles
are available according to
workplace
Approx. -5 kV-
Accessories
Model
45°
±7.5kV
Discharge method
Model
(2) External output
25
ZJ-FW Series
Discharge voltage
Ionization time *
3.0A max
1.2A max
ON (Closed)
OFF (Open)
120
0.9A max
When the discharge stop input is turned ON, the discharge from needles and rotation of fans stops
and external output turns OFF(Open).
External
output
di
a.
ZJ-FW029
24V DC±10%, Ripple (p-p): 10%
[External output]
ON
OFF
.5
ZJ-FW013
Power supply voltage
[Discharge stop input ]
(1) Discharge stop input
Discharge
stop input
44
ZJ9-BRP1FW
65
ZJ9-BRL1FW
Pipe-mounting bracket
Normal operation
70
L-mounting bracket
Operating state Power OFF
IN
85
127.5
155
ZJ9-BRS1FW
At an error, cleaning or
Front cover open
4.5
ZJ9-NDT04FW
Stand
60
Replacement discharge electrode (4-electrode set)*
ZJ-FW053
Load
-R
2.
25
ZJ-FW029
24V
45
ZJ9-FL40FW
45°
Replacement filter ( 6-pack )
10
ZJ-FW013
4.5
Accessory
Current consumption
Full-open structure for easy cleaning
Installation
165
80
Rotation Range
120°
ZJ-FA20
(Stand, L-mounting bracket and pipe-mounting bracket available.)
Accessories
Item
Easy electrode needle replacement
0V
220
Easily installs in places where not applicable before!
The variable DC ionizer simultaneously
generates a large quantity of ions from
separate positive and negative electrode
needles, while a built-in ion balance sensor
controls ion quantity. The result is a good
balance between high speed ionization and
proper ion balance. Moreover, Omron’s
proprietary louver structure efficiently directs
ions to the target.
0V
200
Ionizer with pipe-mounting brackets
The ionizer adopts a full-open structure that allows users to detach
the front cover by just pressing on tabs. This makes electrode
needle cleaning very easy. Moreover, the electrode needles are
configured as a unit that can be easily and safely replaced.
Approx. +5 kV-
149
Easy electrode needle replacement
owing to modular structure
With three sizes available, the ideal ionizer for the installation
environment and ionization area can be selected. Stable
uniform ionization is possible for any kind of work setup from
narrow workbenches to wide lines. Moreover, tedious-to-rig
air ducts used with bar type ionizers are unnecessary, which
also translates into greater energy savings.
Model
High speed ionization by delivering
a high density ion flow on an
efficiently channeled air stream
Electrode replacement
Full-open structure
Variable DC ionization
120
Maintainability
Ideal for narrow
workbenches to wide lines
Model
Ionization performance
4
Easy installation
General DC ionization
Area fan type
Basic fan type
ZJ-FW Series
ZJ-FA20
Ionization time
ZJ-FW029/053
ZJ-FW013
1.0 s 1.5 s
Ion balance
ZJ-FW013
± 10 V
Discharge method
Variable DC
(See “Ionization performance” of the ZJ-FA20.)
ZJ-FW029
Ionization performance
Reliability
High speed ionization
in a slim configuration
Ionization time
Ion generation understood
at a glance by LED lighting
1.2 s
A proprietary louver structure enables a slim configuration
and yet high speed ionization that removes electrostatic
charge in 1 sec or less. As a standard feature, ion balance
adjustment is available and airflow can be set by 4-step
sliding switch. Moreover, when using the standard stand, the
angle can be easily adjusted against a graduated scale.
Ion balance
During ion generation, both the POWER and ION
lamps are lit. This verifies that the ionizer is running
properly. Moreover, a CLEANING lamp notifies users
when it is time to clean the electrode needles.
± 10 V
Ion balance adjustor (Body rear)
Discharge method
Easy angle adjustment with
graduated scale
Variable DC
Cleaning lamp
Ion generation lamp
Power lamp
Reliability
3 slim, lightweight types to choose from.
Four indicators and
an alarm output
let you easily identify
the operating status.
At 6 cm in depth and weighing 1 kg (ZJ-FW029), the ZJ-FW Series has pursued and achieved a slim,
lightweight configuration. These ionizers easily fit on narrow workbenches or in high locations where
previously they could not go. Moreover, you can select a size according to the area of coverage, so
targets are uniformly neutralized.
The Ionizer’s operating status is displayed on easy-to-see
indicators and it can be output to an external device.
Besides the power (PWR) indicator, there are a CLEAN lamp
that lights when it is time for electrode needle maintenance,
an ALM lamp that lights if trouble occurs, and a FAN lamp
that is lit while the fan is operating.
ZJ-FW053
Easy installation.
High speed ionization and technological
sophistication at a reasonable price.
Excellent cost-performance.
Power lamp
Fan running lamp
Alarm lamp
Maintainability
Running status is understood at a glance.
Airblow sticker included
Cleaning notification lamp
Easy to clean and
replace electrode needles
Cleaning is easy and thorough owing to a full-open
structure that allows users to detach the front cover
by just pressing on tabs. Electrode needles can also
be easily replaced, which enables long lasting use of
the product.
The ZJ-FA20 delivers technological sophistication at a low price, featuring high speed ionization
that removes electrostatic charge in 1.2 s, ion balance control via a built-in sensor,
and a full-open structure that makes it easy to clean and replace electrodes.
Electrode cleaning
Variable DC ionization
Input/output circuit
Input and Output logic
Model
0V
* ZJ-FW013: 1 set, ZJ-FW029: 3 sets, ZJ-FW053: 6 sets
Rating/ Performance
ZJ-FW053
External output is ON(Close) state when ZJ-FW is working normally.
External output is OFF(Open) state as one of the below conditions occurs.
Front cover open, Cleaning, Fan rotation error, Malfunction error and Discharge stop input ON
1s
1.5 s
±10V max.
Ion balance *
Outer dimensions ZJ-FW013 (Units: mm)
0.01 ppm (Measured at a distance of 50 mm from air outlet)
Amount of ozone generated
Power (Green), Fan running (Green), Cleaning (Yellow), Alarm (Red)
Indicators
Ion balance adjustment (Automatic and manual)
Main functions
23
4.5
Photo MOS relay output (NPN or PNP)
External output
(for both cleaning
and alarm outputs)
2
20
• Applied voltage: 30VDC max., load current: 100mA max.
• Residual voltage: 1V max
No-voltage contact input
• ON: 0V short circuit
• OFF: Open (leakage current: 0.1mA max.)
0 to 50 ˚C (No icing or dewing)
Ambient humidity range
Weight (Packaged)
35% to 65% (No icing or dewing)
Approx. 0.6 kg (Approx. 1.2 kg)
Material
Accessories
Approx. 1 kg (Approx. 1.8 kg)
Body:Aluminum, ABS
Instruction sheet, I/O connector, L-mounting bracket, Streamer
130
Electrode needle: Tungsten
Instruction sheet, I/O connector, Stand, Streamer
* Typical default settings at the time of shipping from the factory
• Measurement conditions Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
59.5
Approx. 2 kg (Approx. 3 kg)
224.4
ZJ-FW029
A
345.4
Dimensions
B
C
336.4
290
D
360.4
ZJ-FW053
585.4
576.4
600.4
B
C
45°
59.5
60
Rotation range
ZJ-FA20
The ionizer can be used in a variety of postures. It can
be installed on a workbench or mounted on a pole.
It can also be freely angled using the angle adjustment
knob on the body and the screw slots on the stand.
Ion balance sensor
Dispersed airflow
D
45°
530
45°
Replacement filter (10-pack)
ZJ9-FL120N1
Replacement discharge electrode ( 6-pack)
ZJ9-NDT06FN1
60°
60°
3-5.5 dia.
Mounting hole dimensions
100 dia.
8.5
80
120°
12
ZJ-FA20
900 mA max. (When input by included AC adapter)
Vertical positioning
Left-Right swiveling
75
5.5 50 dia.
197.5
140
Current consumption
60°
7-M5
5.5
Discharge voltage
±7kV
50±0.2
Discharge method
Variable DC
15±0.2
Ionization time *2
1.2 s ( 0.8 s when used without filter )
Ion balance *2
Amount of ozone generated
Indicators
Main functions
Material
Accessories
±10 V max.
0.01 ppm (Measured at a distance of 50 mm from air outlet )
High voltage output: ION ( Yellow), Cleaning: CLEANING (Orange ), Power: POWER ( Green)
60°
Ion balance adjustment (Automatic and manual ), airflow adjustment
Working and storage: 0 to 50˚C (No icing or dewing )
Working: 35% to 65%, Storage: 35% to 85% ( No icing or dewing )
Approx. 1.5 kg ( Approx. 2 kg)
Body: ABS, Electrode needle: Tungsten, Stand: SPCC
Instruction sheet, AC adapter, Warning label ( 2 types), FG connection cable ( 2 m)
*1 Use the ionizer only with the included AC adapter.
• Measurement conditions/Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
*2 Typical default settings at time of shipping from the factory
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
Rotation range
ZJ-FA20 ( Units: mm)
Model
24V DC *1
Ambient humidity range
Weight (Packaged)
79.5
Front-Back tilting
Channeled uniform airflow
Outer dimensions
Accessory
Power supply voltage
Ambient temperature range
45°
45°
Ambient temperature range
ZJ-FW029/053 ( Units: mm)
Model
182
70
67.5
95
Discharge stop input
Conventional ionizer
Item
A
188.4
Omron’s proprietary louver structure
Rating/ Performance
45°
Variable DC
ZJ-FA20
Various installation styles
are available according to
workplace
Approx. -5 kV-
Accessories
Model
45°
±7.5kV
Discharge method
Model
(2) External output
25
ZJ-FW Series
Discharge voltage
Ionization time *
3.0A max
1.2A max
ON (Closed)
OFF (Open)
120
0.9A max
When the discharge stop input is turned ON, the discharge from needles and rotation of fans stops
and external output turns OFF(Open).
External
output
di
a.
ZJ-FW029
24V DC±10%, Ripple (p-p): 10%
[External output]
ON
OFF
.5
ZJ-FW013
Power supply voltage
[Discharge stop input ]
(1) Discharge stop input
Discharge
stop input
44
ZJ9-BRP1FW
65
ZJ9-BRL1FW
Pipe-mounting bracket
Normal operation
70
L-mounting bracket
Operating state Power OFF
IN
85
127.5
155
ZJ9-BRS1FW
At an error, cleaning or
Front cover open
4.5
ZJ9-NDT04FW
Stand
60
Replacement discharge electrode (4-electrode set)*
ZJ-FW053
Load
-R
2.
25
ZJ-FW029
24V
45
ZJ9-FL40FW
45°
Replacement filter ( 6-pack )
10
ZJ-FW013
4.5
Accessory
Current consumption
Full-open structure for easy cleaning
Installation
165
80
Rotation Range
120°
ZJ-FA20
(Stand, L-mounting bracket and pipe-mounting bracket available.)
Accessories
Item
Easy electrode needle replacement
0V
220
Easily installs in places where not applicable before!
The variable DC ionizer simultaneously
generates a large quantity of ions from
separate positive and negative electrode
needles, while a built-in ion balance sensor
controls ion quantity. The result is a good
balance between high speed ionization and
proper ion balance. Moreover, Omron’s
proprietary louver structure efficiently directs
ions to the target.
0V
200
Ionizer with pipe-mounting brackets
The ionizer adopts a full-open structure that allows users to detach
the front cover by just pressing on tabs. This makes electrode
needle cleaning very easy. Moreover, the electrode needles are
configured as a unit that can be easily and safely replaced.
Approx. +5 kV-
149
Easy electrode needle replacement
owing to modular structure
With three sizes available, the ideal ionizer for the installation
environment and ionization area can be selected. Stable
uniform ionization is possible for any kind of work setup from
narrow workbenches to wide lines. Moreover, tedious-to-rig
air ducts used with bar type ionizers are unnecessary, which
also translates into greater energy savings.
Model
High speed ionization by delivering
a high density ion flow on an
efficiently channeled air stream
Electrode replacement
Full-open structure
Variable DC ionization
120
Maintainability
Ideal for narrow
workbenches to wide lines
Model
Ionization performance
4
Easy installation
General DC ionization
Area fan type
Basic fan type
ZJ-FW Series
ZJ-FA20
Ionization time
ZJ-FW029/053
ZJ-FW013
1.0 s 1.5 s
Ion balance
ZJ-FW013
± 10 V
Discharge method
Variable DC
(See “Ionization performance” of the ZJ-FA20.)
ZJ-FW029
Ionization performance
Reliability
High speed ionization
in a slim configuration
Ionization time
Ion generation understood
at a glance by LED lighting
1.2 s
A proprietary louver structure enables a slim configuration
and yet high speed ionization that removes electrostatic
charge in 1 sec or less. As a standard feature, ion balance
adjustment is available and airflow can be set by 4-step
sliding switch. Moreover, when using the standard stand, the
angle can be easily adjusted against a graduated scale.
Ion balance
During ion generation, both the POWER and ION
lamps are lit. This verifies that the ionizer is running
properly. Moreover, a CLEANING lamp notifies users
when it is time to clean the electrode needles.
± 10 V
Ion balance adjustor (Body rear)
Discharge method
Easy angle adjustment with
graduated scale
Variable DC
Cleaning lamp
Ion generation lamp
Power lamp
Reliability
3 slim, lightweight types to choose from.
Four indicators and
an alarm output
let you easily identify
the operating status.
At 6 cm in depth and weighing 1 kg (ZJ-FW029), the ZJ-FW Series has pursued and achieved a slim,
lightweight configuration. These ionizers easily fit on narrow workbenches or in high locations where
previously they could not go. Moreover, you can select a size according to the area of coverage, so
targets are uniformly neutralized.
The Ionizer’s operating status is displayed on easy-to-see
indicators and it can be output to an external device.
Besides the power (PWR) indicator, there are a CLEAN lamp
that lights when it is time for electrode needle maintenance,
an ALM lamp that lights if trouble occurs, and a FAN lamp
that is lit while the fan is operating.
ZJ-FW053
Easy installation.
High speed ionization and technological
sophistication at a reasonable price.
Excellent cost-performance.
Power lamp
Fan running lamp
Alarm lamp
Maintainability
Running status is understood at a glance.
Airblow sticker included
Cleaning notification lamp
Easy to clean and
replace electrode needles
Cleaning is easy and thorough owing to a full-open
structure that allows users to detach the front cover
by just pressing on tabs. Electrode needles can also
be easily replaced, which enables long lasting use of
the product.
The ZJ-FA20 delivers technological sophistication at a low price, featuring high speed ionization
that removes electrostatic charge in 1.2 s, ion balance control via a built-in sensor,
and a full-open structure that makes it easy to clean and replace electrodes.
Electrode cleaning
Variable DC ionization
Input/output circuit
Input and Output logic
Model
0V
* ZJ-FW013: 1 set, ZJ-FW029: 3 sets, ZJ-FW053: 6 sets
Rating/ Performance
ZJ-FW053
External output is ON(Close) state when ZJ-FW is working normally.
External output is OFF(Open) state as one of the below conditions occurs.
Front cover open, Cleaning, Fan rotation error, Malfunction error and Discharge stop input ON
1s
1.5 s
±10V max.
Ion balance *
Outer dimensions ZJ-FW013 (Units: mm)
0.01 ppm (Measured at a distance of 50 mm from air outlet)
Amount of ozone generated
Power (Green), Fan running (Green), Cleaning (Yellow), Alarm (Red)
Indicators
Ion balance adjustment (Automatic and manual)
Main functions
23
4.5
Photo MOS relay output (NPN or PNP)
External output
(for both cleaning
and alarm outputs)
2
20
• Applied voltage: 30VDC max., load current: 100mA max.
• Residual voltage: 1V max
No-voltage contact input
• ON: 0V short circuit
• OFF: Open (leakage current: 0.1mA max.)
0 to 50 ˚C (No icing or dewing)
Ambient humidity range
Weight (Packaged)
35% to 65% (No icing or dewing)
Approx. 0.6 kg (Approx. 1.2 kg)
Material
Accessories
Approx. 1 kg (Approx. 1.8 kg)
Body:Aluminum, ABS
Instruction sheet, I/O connector, L-mounting bracket, Streamer
130
Electrode needle: Tungsten
Instruction sheet, I/O connector, Stand, Streamer
* Typical default settings at the time of shipping from the factory
• Measurement conditions Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
59.5
Approx. 2 kg (Approx. 3 kg)
224.4
ZJ-FW029
A
345.4
Dimensions
B
C
336.4
290
D
360.4
ZJ-FW053
585.4
576.4
600.4
B
C
45°
59.5
60
Rotation range
ZJ-FA20
The ionizer can be used in a variety of postures. It can
be installed on a workbench or mounted on a pole.
It can also be freely angled using the angle adjustment
knob on the body and the screw slots on the stand.
Ion balance sensor
Dispersed airflow
D
45°
530
45°
Replacement filter (10-pack)
ZJ9-FL120N1
Replacement discharge electrode ( 6-pack)
ZJ9-NDT06FN1
60°
60°
3-5.5 dia.
Mounting hole dimensions
100 dia.
8.5
80
120°
12
ZJ-FA20
900 mA max. (When input by included AC adapter)
Vertical positioning
Left-Right swiveling
75
5.5 50 dia.
197.5
140
Current consumption
60°
7-M5
5.5
Discharge voltage
±7kV
50±0.2
Discharge method
Variable DC
15±0.2
Ionization time *2
1.2 s ( 0.8 s when used without filter )
Ion balance *2
Amount of ozone generated
Indicators
Main functions
Material
Accessories
±10 V max.
0.01 ppm (Measured at a distance of 50 mm from air outlet )
High voltage output: ION ( Yellow), Cleaning: CLEANING (Orange ), Power: POWER ( Green)
60°
Ion balance adjustment (Automatic and manual ), airflow adjustment
Working and storage: 0 to 50˚C (No icing or dewing )
Working: 35% to 65%, Storage: 35% to 85% ( No icing or dewing )
Approx. 1.5 kg ( Approx. 2 kg)
Body: ABS, Electrode needle: Tungsten, Stand: SPCC
Instruction sheet, AC adapter, Warning label ( 2 types), FG connection cable ( 2 m)
*1 Use the ionizer only with the included AC adapter.
• Measurement conditions/Measurement point and distance: 300 mm from body center, Airflow: Max, Plate monitor: 150 x 150 mm, 20 pF
*2 Typical default settings at time of shipping from the factory
• Ionization time: Time required to lower the charge from ±1000 V to ±100 V
• Ion balance measurement time: 10 s
Rotation range
ZJ-FA20 ( Units: mm)
Model
24V DC *1
Ambient humidity range
Weight (Packaged)
79.5
Front-Back tilting
Channeled uniform airflow
Outer dimensions
Accessory
Power supply voltage
Ambient temperature range
45°
45°
Ambient temperature range
ZJ-FW029/053 ( Units: mm)
Model
182
70
67.5
95
Discharge stop input
Conventional ionizer
Item
A
188.4
Omron’s proprietary louver structure
Rating/ Performance
45°
Variable DC
ZJ-FA20
Various installation styles
are available according to
workplace
Approx. -5 kV-
Accessories
Model
45°
±7.5kV
Discharge method
Model
(2) External output
25
ZJ-FW Series
Discharge voltage
Ionization time *
3.0A max
1.2A max
ON (Closed)
OFF (Open)
120
0.9A max
When the discharge stop input is turned ON, the discharge from needles and rotation of fans stops
and external output turns OFF(Open).
External
output
di
a.
ZJ-FW029
24V DC±10%, Ripple (p-p): 10%
[External output]
ON
OFF
.5
ZJ-FW013
Power supply voltage
[Discharge stop input ]
(1) Discharge stop input
Discharge
stop input
44
ZJ9-BRP1FW
65
ZJ9-BRL1FW
Pipe-mounting bracket
Normal operation
70
L-mounting bracket
Operating state Power OFF
IN
85
127.5
155
ZJ9-BRS1FW
At an error, cleaning or
Front cover open
4.5
ZJ9-NDT04FW
Stand
60
Replacement discharge electrode (4-electrode set)*
ZJ-FW053
Load
-R
2.
25
ZJ-FW029
24V
45
ZJ9-FL40FW
45°
Replacement filter ( 6-pack )
10
ZJ-FW013
4.5
Accessory
Current consumption
Full-open structure for easy cleaning
Installation
165
80
Rotation Range
120°
ZJ-FA20
(Stand, L-mounting bracket and pipe-mounting bracket available.)
Accessories
Item
Easy electrode needle replacement
0V
220
Easily installs in places where not applicable before!
The variable DC ionizer simultaneously
generates a large quantity of ions from
separate positive and negative electrode
needles, while a built-in ion balance sensor
controls ion quantity. The result is a good
balance between high speed ionization and
proper ion balance. Moreover, Omron’s
proprietary louver structure efficiently directs
ions to the target.
0V
200
Ionizer with pipe-mounting brackets
The ionizer adopts a full-open structure that allows users to detach
the front cover by just pressing on tabs. This makes electrode
needle cleaning very easy. Moreover, the electrode needles are
configured as a unit that can be easily and safely replaced.
Approx. +5 kV-
149
Easy electrode needle replacement
owing to modular structure
With three sizes available, the ideal ionizer for the installation
environment and ionization area can be selected. Stable
uniform ionization is possible for any kind of work setup from
narrow workbenches to wide lines. Moreover, tedious-to-rig
air ducts used with bar type ionizers are unnecessary, which
also translates into greater energy savings.
Model
High speed ionization by delivering
a high density ion flow on an
efficiently channeled air stream
Electrode replacement
Full-open structure
Variable DC ionization
120
Maintainability
Ideal for narrow
workbenches to wide lines
Model
Ionization performance
4
Easy installation
General DC ionization
N EW
Read and Understand this Catalog
Easy to use
Standard type for a fan type ionizer with high performance
Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any questions or comments.
Slim & Light
Fan Ionizer
ZJ-FW Series
ZJ-FA20
Area fan type ionizer that can fit anywhere
Warranty and Limitations of Liability
WARRANTY
LIMITATIONS OF LIABILITY
OMRON's exclusive warranty is that the products are free from defects in
materials and workmanship for a period of one year (or other period if
specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR
IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER
OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE
REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL
LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER
SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR
STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the
individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY,
REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
ZJ-FW053
530mm
A new concept
from the production floor.
59.5mm
70mm
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes,
or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party
certification documents identifying ratings and limitations of use that apply to
the products. This information by itself is not sufficient for a complete
determination of the suitability of the products in combination with the end
product, machine, system, or other application or use.
The following are some examples of applications for which particular
attention must be given. This is not intended to be an exhaustive list of all
possible uses of the products, nor is it intended to imply that the uses listed
may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems,
aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or
government regulations.
ZJ-FW013
130mm
ZJ-FW029
• Systems, machines, and equipment that could present a risk to life or
property.
290mm
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Basic fan type
ZJ-FA20
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a
programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
PERFORMANCE DATA
Product specifications and accessories may be changed at any time based
on improvements and other reasons.
Basic fan type
ZJ - FA20
Pick me up,
when you are not
sure that what
kind of fan ionizer
should be used!
This is the standard for a fan type
ionizer, which is easy-to-use and
has high performance.
Various installation
styles are
available to match
the workplace.
It is our practice to change model numbers when published ratings or
features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any
notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please
consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
Performance data given in this catalog is provided as a guide for the user in
determining suitability and does not constitute a warranty. It may represent
the result of OMRON’s test conditions, and the users must correlate it to
actual application requirements. Actual performance is subject to the
OMRON Warranty and Limitations of Liability.
Area fan type
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed
to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
Slim,
lightweight body
3 types
to choose
from by
area coverage
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for
manufacturing purposes, even when tolerances are shown.
6 cm thick
Just
1kg in weight
*
ZJ-FW Series
This ionizer series is designed to go anywhere.
All models are easily installed on narrow
workbenches or in high positions where earlier
models presented installation issues.
* ZJ-FW029
Ionization area vs. Ionization time
OMRON Corporation
2.5
300
Ionization time (s)
Airflow level 1
200
2.0
3
4
1.0
Contact: www.ia.omron.com
3s 4s
1s 2s
Regional Headquarters
0
MAX:5
-100
0.5
0
0.5
0.8
1.0
1.3
Airflow (m/s)
1.5
1.8
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
-200
-300
(mm) 0
Authorized Distributor:
Area fan type
Airflow vs. Ionization time
ZJ-FW Series
2.5
Tokyo, JAPAN
100
2
1.5
Industrial Automation Company
NEW
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
Ionization time (s)
Airflow vs. Ionization time
OMRON EUROPE B.V.
Sensor Business Unit
OMRON ELECTRONICS LLC
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
IL 60173-5302 U.S.A.
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
OMRON (CHINA) CO., LTD.
© OMRON Corporation 2012
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Room 2211, Bank of China Tower,
In the interest of product improvement,
Alexandra Technopark,
200 Yin Cheng Zhong Road,
specifications are subject to change without notice.
Singapore 119967
PuDong New Area, Shanghai, 200120, China
Tel: (65) 6835-3011/Fax: (65) 6835-2711
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
CSM_2_2_0413
Cat. No. E420-E1-01
One Commerce Drive Schaumburg,
Airflow level 1
FW013
2.0
0112 (0112)
0
FW029
FW053
1
1.5
ZJ-FW053
300
300
200
1s 2s 3s 4s 5s
100
1s
2s
3s 4s 5s
100
1s
2s 3s
4s
5s
200
100
2
3
4
0
0
0
4
-100
-100
-100
-200
-200
-200
-300
(mm) 0
-300
(mm) 0
0.5
All Rights Reserved.
ZJ-FW029
300
3
1
1.0
ZJ-FW013
200
2
1.5
Ionization area vs. Ionization time
2
2.5
Airflow (m/s)
3
3.5
Measurement conditions
Distance from measurement point: 300 mm
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
Measurement conditions
Airflow: Max.
Ionization time: ±1000 V to ±100 V
Plate monitor: 150 x 150 mm, 20 pF
200 400 600 800 1000 1200 1400
Distance
(mm)
-300
(mm) 0
200 400 600 800 1000 1200 1400
Distance
(mm)