8WH2 Spring-Loaded Terminals 4 4/2 Introduction 4/3 General data on 8WH 4/7 8WH through-type terminals1) 4/18 8WH hybrid through-type terminals1) 4/21 8WH fuse terminals 4/23 8WH isolating blade terminals 4/25 8WH isolating terminals 4/27 8WH two-tier terminals1) 4/33 8WH three-tier terminals 4/35 8WH four-tier motor terminals 4/37 8WH diode terminals 4/39 8WH two-tier diode terminals 1) Also available as a PE version More technical product information: Service&Support Portal: www.support.automation.siemens.com. Product List: Technical specifications Entry List: Updates / Downloads / FAQ / Manuals / Operating instructions / Characteristic curves / Certificates 4 8WH2 Spring-Loaded Terminals Introduction ■ Overview Devices Page Application Through-type terminals 4/7 Connection of incoming and outgoing conductors up to 35 mm2 Hybrid through-type terminals 4/18 Terminals with a range of connection methods Fuse terminals 4/21 Terminals which can be used to protect control circuits, for example Isolating blade terminals 4/23 Isolation of the circuit, e.g. for test purposes Isolating terminals 4/25 Isolation of the circuit, e.g. for test purposes Two-tier terminals 4/27 Compact form of the terminal block in which two connection wires can be installed Three-tier terminals 4/33 Compact terminal blocks up to 2.5 mm2, in which three connection wires can be installed Four-tier motor terminals 4/35 Compact terminal blocks up to 4 mm2, in which three connection wires plus PE can be installed Diode terminals 4/37 Terminal blocks with integrated diodes Two-tier diode terminals 4/39 Terminal blocks with integrated diodes 8WH terminals 4 4/2 8WH2 Spring-Loaded Terminals General data on 8WH ■ Overview Terminal type Standard spring-loaded connection Design Standard No. of clamping points 2 3 4 4 6 Order No. (digits 1 ... 7) 8WH2 000 8WH2 003 8WH2 004 8WH2 020 8WH2 023 Conductor cross-section Terminal type1) Color 1.5 mm2 Through-type 2.5 mm2 4 mm2 6 mm2 10 mm2 16 mm2 35 mm2 4 Gray ✔ ✔ ✔ ✔ -- 0AE00 Blue ✔ ✔ ✔ ✔ -- 0AE01 PE Green/yellow ✔ ✔ ✔ ✔ -- 0CE07 Through-type Gray ✔ ✔ ✔ ✔ ✔ 0AF00 Blue ✔ ✔ ✔ ✔ ✔ 0AF01 Isolating Gray ✔ ✔ ✔ -- -- 6AF00 Isolating blade Gray ✔ ✔ ✔ -- -- 0CF00 PE Green/yellow ✔ ✔ ✔ ✔ ✔ 0CF07 Through-type Gray ✔ ✔ ✔ ✔ -- 0AG00 Blue ✔ ✔ ✔ ✔ -- 0AG01 Isolating Gray ✔ -- -- -- -- 6AG00 Isolating blade Gray ✔ -- -- -- -- 6CG00 PE Green/yellow ✔ ✔ ✔ ✔ -- 0CG07 Through-type Gray ✔ ✔ -- -- -- 0AH00 Blue ✔ ✔ -- -- -- 0AH01 PE Green/yellow ✔ ✔ -- -- -- 0CH07 Through-type Gray ✔ -- -- -- -- 0AJ00 Blue ✔ -- -- -- -- 0AJ01 PE Green/yellow ✔ -- -- -- -- 0CJ07 Through-type Gray ✔ -- -- -- -- 0AK00 Blue ✔ -- -- -- -- 0AK01 PE Green/yellow ✔ -- -- -- -- 0CK07 Through-type Gray ✔ -- -- -- -- 0AM00 Blue ✔ -- -- -- -- 0AM01 Green/yellow ✔ -- -- -- -- 0CM07 PE 1) Order No. (digits 8 ... 12) Two-tier Only the main terminal types are listed here.You will find further versions on the following pages. 4/3 8WH2 Spring-Loaded Terminals General data on 8WH 4 The space-saving design and conductor routing from above make spring-loaded terminals ideal for controlgear installations with minimum available space. The terminals are open at one end and can be closed using the appropriate covers. The large and unambiguous marking in the center of the terminal is essential for ensuring reliable installation in minimum time. Each clamping point can also be separately labeled. Spring-loaded terminals provide a large connection compartment for fast wiring of flexible and rigid conductors, including conductors with nominal cross-section and a fitted end sleeve. Reducing combs enable easy connection of terminals with various nominal cross-section. For example, they can be used for the fast creation of infeed blocks, e.g. by connecting a 10 mm² spring-loaded terminal with a 2.5 or 4 mm² spring-loaded terminal. 4/4 8WH2 Spring-Loaded Terminals General data on 8WH 4 The 2 to 50-pole connecting combs also considerably reduce the time needed for assembly and wiring as they enable up to 50 terminals to be connected in a single step. The universal plug-in zones of the isolating terminal can accommodate the isolated through-type connectors, isolating plugs, component connectors and fused connectors. Contact tabs can be removed from the standard comb in order to skip individual terminals. This means that two potentials can run in parallel on a single terminal strip. The contact points can additionally be marked. The component connector enables the convenient equipping with electronic components. One turn of the screwdriver opens the contact points and the component is easily inserted. 4/5 8WH2 Spring-Loaded Terminals General data on 8WH 4 A comprehensive range of test accessories is also available for the spring-loaded terminal series. The test adapters for Ø 4 mm test plugs and modular test plugs enable all measuring and testing jobs to be performed in minimum time. Cover segments are used to cover the projecting terminal segments of three and four-wire terminals when mounting two-wire terminals side-by-side. This ensures touch protection. Note: The accessories for 8WH can only be used for 8WH terminals. The compartment partitions project beyond the contours of the terminals and separate the groups both visually and electrically. 4/6 8WH2 Spring-Loaded Terminals 8WH through-type terminals ■ Overview With two clamping points The through-type terminals have an impressive space-saving design and offer optimized handling. With its front connection arrangement this series provides additional space between the cable ducts for wiring. The double bridge shaft enables individual chain bridging with connecting combs. Accessories are available for testing and labeling. With three clamping points Terminals with three clamping points are a space-saving alternative to the standard through-type terminals for branching the potential. It is often necessary for three conductors to be routed to a single terminal.This three clamping point version enables this without the need for additional terminals and jumpers. With four clamping points The double connection of the through-type terminals with four clamping points enables four conductors to be connected to a single potential. These versions with four clamping points are therefore suitable for use as compact potential distributors. A label can be snapped on to the middle of each terminal at the front. Further labels can also be mounted flat on the side of the terminals. PE/ground conductor function The PE through-type terminals are available with the same contour as the through-type terminals. Simply snap the terminals onto the support rail to achieve full mechanical and electrical contact with the support rail. The PE through-type terminals meet all the requirements of IEC 60947-7-2: • Low contact resistance • Stainless clamping points • Green-yellow enclosure • Additional inscription options ■ Technical specifications 8WH2 000-0AE0. Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 8WH2 000-0CE07 8WH2 003-0AE00 8WH2 003-0CE07 8WH2 004-0AE00 8WH2 003-0AE01 8WH2 004-0AE01 4.2 / 48.5 / 2.2 36.8 / 44 17.5 / 1.5 6/3 4.2 / 60.5 / 2.2 36.5 / 44 4.2 / 72 / 2.2 -- 17.5 / 1.5 -- 17.5 / 1.5 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 1.5 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 1.5 0.5 • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² Stripped length in mm 10 Plug gauge (IEC 60947-1) A1 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 300 / 15 / 26-14 300 / 15 / 26-14 -- / -- / 26-14 -- / -- / 26-14 300 / 15 / 26-14 300 / 15 / 26-14 -- / -- / 26-14 -- 300 / 15 / 26-14 300 / 15 / 26-14 Support rails/protective conductor busbars -- See section "Support rails" on page 1/3 -- See section "Support rails" on page 1/3 -- 4/7 4 8WH2 Spring-Loaded Terminals 8WH through-type terminals 8WH2 004-0CE07 8WH2 000-0AF0. 4 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 4.2 / 72 / 2.2 36.5 / 44 5.2 / 48.5 / 2.2 36.8 / 44 -6/3 31 / 4 8/3 Stripped length in mm 10 Plug gauge (IEC 60947-1) A1 Molded plastic type • Flammability class acc. to UL 94 PA V0 - UL/cUL: in V/A / AWG - CSA: in V/A / AWG Support rails/protective conductor busbars Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 8WH2 003-0CF07 5.2 / 60.5 / 2.2 36.5 / 44 -- 28 / 4 -- -- / -- / 26-12 600 / 20 / 26-12 -- / -- / 26-12 See section "Support rails" on page 1/3 0.25 ... 2.5 0.25 ... 2.5 A3 -- / -- / 26-14 300 / 20 / 26-12 -- / -- / 26-14 -- See section "Support rails" on page 1/3 -- See section "Support rails" on page 1/3 -- 8WH2 004-0AF00 8WH2 004-0AF01 8WH2 004-0CF07 8WH2 000-0AG0. 8WH2 003-0AG00 8WH2 004-0AG00 8WH2 003-0AG01 8WH2 004-0AG01 6.2 / 56 / 2.2 36.8 / 44 6.2 / 71.5 / 2.2 36.5 / 44 6.2 / 87 / 2.2 -- -- 5.2 / 72 / 2.2 36.5 / 44 28 / 4 8/3 -- 40 / 6 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 2.5 0.5 • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 4 0.25 ... 4 0.5 ... 1 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 600 / 20 / 26-12 -- -- / -- / 26-12 600 / 30 / 20-10 Support rails/protective conductor busbars -- See section "Support rails" on page 1/3 -- 4/8 8WH2 003-0AF00 8WH2 003-0AF01 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 1.5 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 1.5 0.5 • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes 8WH2 000-0CF07 A4 8WH2 Spring-Loaded Terminals 8WH through-type terminals 8WH2 000-0CG07 8WH2 003-0CG07 8WH2 004-0CG07 8WH2 000-0AH00 8WH2 003-0AH00 8WH2 000-0AH01 8WH2 003-0AH01 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm 6.2 / 56 / 2.2 36.8 / 44 6.2 / 71.5 / 2.2 36.5 / 44 6.2 / 87 / 2.2 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² -• Rated impulse withstand voltage in kV / pollution degree 8 / 3 III / I • Overvoltage category / molded plastic group 8.2 / 69.5 / 2.2 43.5 / 51 0.25 ... 6 0.25 ... 6 0.5 ... 1.5 Stripped length in mm 10 12 Plug gauge (IEC 60947-1) A4 A5 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG -- / -- / 20-10 -- Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm See section "Support rails" on page 1/3 600 / 50 / 20-8 See section "Support rails" on page 1/3 See section "Support rails" on page 1/3 8WH2 003-0CH07 8WH2 000-0AJ00 8WH2 000-0AJ01 8.2 / 69.5 / 2.2 43.5 / 51 8.2 / 90.5 / 2.2 10 / 71.5 / 2.2 50.5 / 58 -- 8WH2 000-0CJ07 65 / 16 Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 6 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 6 • Flexible with two-wire connection end sleeve, with plastic 0.5 ... 1.5 sleeve in mm² 0.25 ... 10 0.25 ... 10 1.5 ... 2.5 Stripped length in mm 12 18 Plug gauge (IEC 60947-1) A5 A6 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG -- / -- / 20-8 -- Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm -- 8WH2 000-0CH07 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² -• Rated impulse withstand voltage in kV / pollution degree 8 / 3 III / I • Overvoltage category / molded plastic group Support rails/protective conductor busbars 4 52 / 10 Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 4 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 4 • Flexible with two-wire connection end sleeve, with plastic 0.5 ... 1 sleeve in mm² Support rails/protective conductor busbars 8.2 / 90.5 / 2.2 600 / 65 / 16-6 -- / -- / 16-6 See section "Support rails" on page 1/3 See section "Support rails" on page 1/3 -- See section "Support rails" on page 1/3 8WH2 000-0AK00 8WH2 000-0AK01 8WH2 000-0CK07 8WH2 000-0AM00 8WH2 000-0AM01 8WH2 000-0CM07 12 / 80 / 2.2 51 / 58.5 16 / 100 / -59 / 66.5 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² 90 / 25 • Rated impulse withstand voltage in kV / pollution degree 8 / 3 III / I • Overvoltage category / molded plastic group 125 / 35 Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25... 16 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 16 • Flexible with two-wire connection end sleeve, with plastic 1.5 ... 4 sleeve in mm² 2.5 ... 35 2.5 ... 35 2.5 ... 10 Stripped length in mm 18 25 Plug gauge (IEC 60947-1) A7 A8 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 600 / 85 / 16-4 -- -- / -- / 16-4 600 / 115 / 14-2 600 / 115 / 14-2 -- / -- / 14-2 -- / -- / 14-2 Support rails/protective conductor busbars -- See section "Support rails" on page 1/3 -- See section "Support rails" on page 1/3 4/9 8WH2 Spring-Loaded Terminals 8WH through-type terminals ■ Selection and ordering data Version 4 Order No. MOQ* Terminal size 1.5 mm² 8WH2 000-0AE00 Through-type terminals, terminal size 1.5 mm² • Terminal width 4.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 1.5 mm² - Flexible 0.08 ... 1.5 mm² - AWG 28-16 - I = 17.5 A - The total current through all connected conductors must not exceed the max. load current - U = 500 V Versions 8WH2 003-0AE00 • Two clamping points - Gray - Blue - Orange - Red 8WH2 000-0AE00 8WH2 000-0AE01 8WH2 000-0AE04 8WH2 000-0AE02 50 units 50 units 50 units 50 units 8WH2 000-0AE08 8WH2 000-0AE03 8WH2 000-0AE05 8WH2 000-0AE06 50 units 50 units 50 units 50 units • Three clamping points - Gray, s - Blue 8WH2 003-0AE00 8WH2 003-0AE01 50 units 50 units • Four clamping points - Gray, s - Blue 8WH2 004-0AE00 8WH2 004-0AE01 50 units 50 units 8WH2 000-0CE07 8WH2 003-0CE07 8WH2 004-0CE07 50 units 50 units 50 units 8WH2 004-0AE00 Black Green White Yellow PE through-type terminals, terminal size 1.5 mm² • Terminal width 4.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 1.5 mm² - Flexible 0.08 ... 1.5 mm² - AWG 28-16 • Green/yellow 8WH2 000-0CE07 Versions • Two clamping points, s • Three clamping points • Four clamping points, s I201_12661 8WH2 000-0CE07 8WH2 003-0CE07 I201_12662 8WH2 003-0CE07 8WH2 004-0CE07 I201_12663 8WH2 004-0CE07 4/10 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* Terminal size 2.5 mm² 8WH2 000-0AF00 Through-type terminals, terminal size 2.5 mm², two clamping points • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 31 A - U = 800 V 4 Versions 8WH2 003-0AF00 • • • • Gray Blue Orange Red 8WH2 000-0AF00 8WH2 000-0AF01 8WH2 000-0AF04 8WH2 000-0AF02 50 units 50 units 50 units 50 units • • • • Black Green White Yellow 8WH2 000-0AF08 8WH2 000-0AF03 8WH2 000-0AF05 8WH2 000-0AF06 50 units 50 units 50 units 50 units 8WH2 003-0AF00 8WH2 003-0AF01 50 units 50 units 8WH2 004-0AF00 8WH2 004-0AF01 50 units 50 units Through-type terminals, terminal size 2.5 mm², three clamping points • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 28 A - The total current through all connected conductors must not exceed the max. load current - U = 800 V Versions • Gray • Blue 8WH2 004-0AF00 Through-type terminals, terminal size 2.5 mm², four clamping points • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 28 A - The total current through all connected conductors must not exceed the max. load current - U = 800 V Versions • Gray • Blue * You can order this quantity or a multiple thereof. 4/11 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* PE through-type terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 • Green/yellow 4 8WH2 000-0CF07 Versions • Two clamping points • Three clamping points • Four clamping points 8WH2 000-0CF07 8WH2 003-0CF07 8WH2 004-0CF07 50 units 50 units 50 units I201_12664 8WH2 000-0CF07 8WH2 003-0CF07 I201_12665 8WH2 003-0CF07 8WH2 004-0CF07 I201_12666 8WH2 004-0CF07 4/12 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* Terminal size 4 mm² Through-type terminals, terminal size 4 mm², two clamping points • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 40 A, U = 800 V 8WH2 000-0AG00 8WH2 003-0AG00 4 Versions • • • • Gray Blue Orange Red 8WH2 000-0AG00 8WH2 000-0AG01 8WH2 000-0AG04 8WH2 000-0AG02 50 units 50 units 50 units 50 units • • • • Black Green White Yellow 8WH2 000-0AG08 8WH2 000-0AG03 8WH2 000-0AG05 8WH2 000-0AG06 50 units 50 units 50 units 50 units 8WH2 003-0AG00 8WH2 003-0AG01 50 units 50 units 8WH2 004-0AG00 8WH2 004-0AG01 50 units 50 units Through-type terminals, terminal size 4 mm², three clamping points • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 40 A, the total current through all connected conductors must not exceed the max. load current - U = 800 V Versions • Gray • Blue 8WH2 004-0AG00 Through-type terminals, terminal size 4 mm², four clamping points • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 40 A, the total current through all connected conductors must not exceed the max. load current - U = 800 V Versions • Gray • Blue * You can order this quantity or a multiple thereof. 4/13 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version 4 8WH2 000-0CG07 Order No. MOQ* PE through-type terminals, terminal size 4 mm² • Terminal width 6.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 • Green/yellow Versions • Two clamping points • Three clamping points • Four clamping points 8WH2 000-0CG07 8WH2 003-0CG07 8WH2 004-0CG07 50 units 50 units 50 units I201_12667 8WH2 000-0CE07 8WH2 003-0CG07 I201_12668 8WH2 003-0CG07 8WH2 004-0CG07 I201_12669 8WH2 004-0CG07 4/14 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* Terminal size 6 mm² 8WH2 000-0AH00 Through-type terminals, terminal size 6 mm², two clamping points • Terminal width 8.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.2 ... 10 mm² - Flexible 0.2 ... 6 mm² - AWG 24-8 - I = 52 A - U = 1000 V 4 Versions 8WH2 000-0CH07 • Gray • Blue 8WH2 000-0AH00 8WH2 000-0AH01 50 units 50 units PE through-type terminals, terminal size 6 mm², two clamping points • Terminal width 8.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.2 ... 10 mm² - Flexible 0.2 ... 6 mm² - AWG 24-8 • Green/yellow 8WH2 000-0CH07 50 units • Gray • Blue 8WH2 003-0AH00 8WH2 003-0AH01 50 units 50 units PE through-type terminals, terminal size 6 mm², three clamping points • Terminal width 8.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.2 ... 10 mm² - Flexible 0.2 ... 6 mm² - AWG 24-8 • Green/yellow 8WH2 003-0CH07 50 units 8WH2 000-0AJ00 8WH2 000-0AJ01 50 units 50 units I201_12670 8WH2 000-0CE07 8WH2 003-0AH00 Through-type terminals, terminal size 6 mm², three clamping points • Terminal width 8.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.2 ... 10 mm² - Flexible 0.2 ... 6 mm² - AWG 24-8 - I = 52 A - The total current through all connected conductors must not exceed the max. load current - U = 1000 V Versions 8WH2 003-0CH07 I201_12671 8WH2 003-0CE07 Terminal size 10 mm² 8WH2 000-0AJ00 Through-type terminals, terminal size 10 mm² • Terminal width 10.2 mm • CUUS • IEC 60947-7-1 - Rigid 1.5 ... 16 mm² - Flexible 1.5 ... 10 mm² - AWG 24-6 - I = 65 A - U = 1000 V Versions • Gray • Blue * You can order this quantity or a multiple thereof. 4/15 8WH2 Spring-Loaded Terminals 8WH through-type terminals 4 8WH2 000-0CJ07 Version Order No. MOQ* PE through-type terminals, terminal size 10 mm² • Terminal width 10.2 mm • CUUS • IEC 60947-7-2 - Rigid 1.5 ... 16 mm² - Flexible 1.5 ... 10 mm² - AWG 24-6 - I = 65 A • Green/yellow 8WH2 000-0CJ07 50 units • Gray • Blue 8WH2 000-0AK00 8WH2 000-0AK01 50 units 50 units PE through-type terminals, terminal size 16 mm² • Terminal width 12 mm • CUUS • IEC 60947-7-2 - Rigid 1.5 ... 25 mm² - Flexible 1.5 ... 16 mm² - AWG 24-4 - I = 90 A • Green/yellow 8WH2 000-0CK07 25 units I201_12672 8WH2 000-0CJ07 Terminal size 16 mm² 8WH2 000-0AK00 Through-type terminals, terminal size 16 mm² • Terminal width 12 mm • CUUS • IEC 60947-7-1 - Rigid 1.5 ... 25 mm² - Flexible 1.5 ... 16 mm² - AWG 24-4 - I = 90 A - U = 1000 V Versions 8WH2 000-0CK07 I201_12673 8WH2 000-0CK07 4/16 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* Terminal size 35 mm² 8WH2 000-0AM00 Through-type terminals, terminal size 35 mm² • Terminal width 16 mm • CUUS • IEC 60947-7-1 - Rigid 2.5 ... 35 mm² - Flexible 2.5 ... 35 mm² - AWG 14-2 - I = 125 A - U = 1000 V • Enclosed at both ends 4 Versions 8WH2 000-0CM07 • Gray, s • Blue 8WH2 000-0AM00 8WH2 000-0AM01 10 units 10 units PE through-type terminals, terminal size 35 mm² • Terminal width 16 mm • CUUS, s • IEC 60947-7-2 - Rigid 2.5 ... 35 mm² - Flexible 2.5 ... 35 mm² - AWG 14-2 - I = 125 A • Enclosed at both ends • Green/yellow 8WH2 000-0CM07 10 units 8WH9 070-0AA00 8WH9 070-0GA00 8WH9 070-0HA00 8WH9 070-0DA00 50 units 50 units 50 units 50 units • For terminal size 1.5 ... 2.5 mm² and two clamping points • For terminal size 1.5 ... 2.5 mm² and three clamping points • For terminal size 1.5 ... 2.5 mm² and four clamping points 8WH9 000-1GA00 8WH9 000-2GA00 8WH9 000-4GA00 50 units 50 units 50 units • For terminal size 4 mm² and two clamping points • For terminal size 4 mm² and three clamping points • For terminal size 4 mm² and four clamping points 8WH9 003-1GA00 8WH9 003-2GA00 8WH9 003-4GA00 50 units 50 units 50 units • For terminal size 6 mm² and two clamping points • For terminal size 6 mm² and three clamping points 8WH9 004-1GA00 8WH9 004-2GA00 50 units 50 units • For terminal size 10 mm² • For terminal size 16 mm² 8WH9 005-1GA00 8WH9 006-1GA00 50 units 50 units 8WH9 000-0GA00 8WH9 003-0GA00 10 units 10 units • For terminal size 1.5 mm² • For terminal size 2.5 mm² • For terminal size 4 mm² 8WH9 061-5AA06 8WH9 060-5AA06 8WH9 063-5AA06 50 units 50 units 50 units • • • • 8WH9 064-5AA06 8WH9 065-5AA06 8WH9 066-5AA06 8WH9 067-5AA06 10 units 25 units 25 units 10 units I201_12674 8WH2 000-0CM07 Accessories Compartment partitions • For visual and electrical separation of terminal groups • 2 mm thick Versions 8WH9 070-0AA00 • • • • For terminal size 1.5 ... 4 mm² and two clamping points For terminal size 1.5 ... 4 mm² and three clamping points For terminal size 1.5 ... 4 mm² and four clamping points For terminal size 6 mm² Covers Gray Versions 8WH9 000-1GA00 Cover segments • Gray • For covering multi-wire terminals when mounting two-wire terminals sideby-side 8WH9 000-0GA00 Versions • For terminal size 1.5 ... 2.5 mm² • For terminal size 4 mm² Warning covers Note: For the operating shafts of 8WH2 through-type terminals Versions 8WH9 061-5AA06 For terminal size 6 mm² For terminal size 10 mm² For terminal size 16 mm² For terminal size 35 mm² Note: For general accessories for 8WH terminal blocks, see chapter 8. * You can order this quantity or a multiple thereof. 4/17 8WH2 Spring-Loaded Terminals 8WH through-type terminals 4 8WH2 000-0CJ07 Version Order No. MOQ* PE through-type terminals, terminal size 10 mm² • Terminal width 10.2 mm • CUUS • IEC 60947-7-2 - Rigid 1.5 ... 16 mm² - Flexible 1.5 ... 10 mm² - AWG 24-6 - I = 65 A • Green/yellow 8WH2 000-0CJ07 50 units • Gray • Blue 8WH2 000-0AK00 8WH2 000-0AK01 50 units 50 units PE through-type terminals, terminal size 16 mm² • Terminal width 12 mm • CUUS • IEC 60947-7-2 - Rigid 1.5 ... 25 mm² - Flexible 1.5 ... 16 mm² - AWG 24-4 - I = 90 A • Green/yellow 8WH2 000-0CK07 25 units I201_12672 8WH2 000-0CJ07 Terminal size 16 mm² 8WH2 000-0AK00 Through-type terminals, terminal size 16 mm² • Terminal width 12 mm • CUUS • IEC 60947-7-1 - Rigid 1.5 ... 25 mm² - Flexible 1.5 ... 16 mm² - AWG 24-4 - I = 90 A - U = 1000 V Versions 8WH2 000-0CK07 I201_12673 8WH2 000-0CK07 4/16 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH through-type terminals Version Order No. MOQ* Terminal size 35 mm² 8WH2 000-0AM00 Through-type terminals, terminal size 35 mm² • Terminal width 16 mm • CUUS • IEC 60947-7-1 - Rigid 2.5 ... 35 mm² - Flexible 2.5 ... 35 mm² - AWG 14-2 - I = 125 A - U = 1000 V • Enclosed at both ends 4 Versions 8WH2 000-0CM07 • Gray, s • Blue 8WH2 000-0AM00 8WH2 000-0AM01 10 units 10 units PE through-type terminals, terminal size 35 mm² • Terminal width 16 mm • CUUS, s • IEC 60947-7-2 - Rigid 2.5 ... 35 mm² - Flexible 2.5 ... 35 mm² - AWG 14-2 - I = 125 A • Enclosed at both ends • Green/yellow 8WH2 000-0CM07 10 units 8WH9 070-0AA00 8WH9 070-0GA00 8WH9 070-0HA00 8WH9 070-0DA00 50 units 50 units 50 units 50 units • For terminal size 1.5 ... 2.5 mm² and two clamping points • For terminal size 1.5 ... 2.5 mm² and three clamping points • For terminal size 1.5 ... 2.5 mm² and four clamping points 8WH9 000-1GA00 8WH9 000-2GA00 8WH9 000-4GA00 50 units 50 units 50 units • For terminal size 4 mm² and two clamping points • For terminal size 4 mm² and three clamping points • For terminal size 4 mm² and four clamping points 8WH9 003-1GA00 8WH9 003-2GA00 8WH9 003-4GA00 50 units 50 units 50 units • For terminal size 6 mm² and two clamping points • For terminal size 6 mm² and three clamping points 8WH9 004-1GA00 8WH9 004-2GA00 50 units 50 units • For terminal size 10 mm² • For terminal size 16 mm² 8WH9 005-1GA00 8WH9 006-1GA00 50 units 50 units 8WH9 000-0GA00 8WH9 003-0GA00 10 units 10 units • For terminal size 1.5 mm² • For terminal size 2.5 mm² • For terminal size 4 mm² 8WH9 061-5AA06 8WH9 060-5AA06 8WH9 063-5AA06 50 units 50 units 50 units • • • • 8WH9 064-5AA06 8WH9 065-5AA06 8WH9 066-5AA06 8WH9 067-5AA06 10 units 25 units 25 units 10 units I201_12674 8WH2 000-0CM07 Accessories Compartment partitions • For visual and electrical separation of terminal groups • 2 mm thick Versions 8WH9 070-0AA00 • • • • For terminal size 1.5 ... 4 mm² and two clamping points For terminal size 1.5 ... 4 mm² and three clamping points For terminal size 1.5 ... 4 mm² and four clamping points For terminal size 6 mm² Covers Gray Versions 8WH9 000-1GA00 Cover segments • Gray • For covering multi-wire terminals when mounting two-wire terminals sideby-side 8WH9 000-0GA00 Versions • For terminal size 1.5 ... 2.5 mm² • For terminal size 4 mm² Warning covers Note: For the operating shafts of 8WH2 through-type terminals Versions 8WH9 061-5AA06 For terminal size 6 mm² For terminal size 10 mm² For terminal size 16 mm² For terminal size 35 mm² Note: For general accessories for 8WH terminal blocks, see chapter 8. * You can order this quantity or a multiple thereof. 4/17 8WH2 Spring-Loaded Terminals 8WH hybrid through-type terminals ■ Overview The terminal connection compartment, on the spring-loaded side as well as on the screw side, enables connection to a nominal cross-section of 2.5 mm² or 4 mm², with or without end sleeves. The advantages of the different connection types are due to the fact that the spring-loaded terminal of the hybrid through-type terminal is used inside the control cabinet and the universal screw terminal is used at the end-user's side. A PE terminal with the same contour is available for the three-wire terminal. Contact is made by simply snapping the terminal onto the support rail. 4 This meets the requirements of IEC 60947-7-2: • Low contact resistance • Stainless clamping points • Green-yellow enclosure • Additional inscription options. A label can be snapped on to the middle of each terminal at the front. Further labels can also be mounted flat on the side of the terminals. ■ Technical specifications 8WH2 103-2BF00 8WH2 103-2BF01 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm 5.2 / 65.3 / 2.2 42.8 / 50.3 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 28 / 4 8/3 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 ... 1 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 8WH2 103-3BF07 8WH2 103-2BG00 8WH2 103-2BG01 6.2 / 74.4 / 2.2 -- 32 / 6 -- 0.25 ... 4 0.25 ... 4 A4 Connection capacity of screw terminal • Flexible with end sleeves with/without plastic sleeve in mm² 0.25 ... 2.5 / 0.25 ... 2.5 0.25 ... 4 / 0.25 ... 4 Multi-conductor connection (two conductors of same crosssection) • Rigid/flexible in mm² 0.14 ... 1.5 / 0.14 ... 1.5 0.25 ... 1.5 • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic 0.5 ... 1.5 sleeve in mm² 0.5 ... 2.5 Stripped length in mm 9 Plug gauge (IEC 60947-1) A3 A4 Tightening torque in Nm 0.6 ... 0.8 0.6.....0.8 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG Applied for Applied for Support rails/protective conductor busbars -- 4/18 8WH2 103-3BG07 See section "Support rails" on page 1/3 -- See section "Support rails" on page 1/3 8WH2 Spring-Loaded Terminals 8WH hybrid through-type terminals ■ Selection and ordering data Version Order No. MOQ* 4 Terminal size 2.5 mm² 8WH2 103-2BF00 Hybrid through-type terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • IEC 60947-7-1 • Spring - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 28 A - The total current through all connected conductors must not exceed the max. load current - U = 800 V • Screw - Rigid 0.14 ... 4 mm² - Flexible 0.14 ... 2.5 mm² - AWG 26-14 - I = 28 A - U = 800 V Versions 8WH2 103-3BF07 • Gray • Blue 8WH2 103-2BF00 8WH2 103-2BF01 50 units 50 units PE hybrid through-type terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • IEC 60947-7-2 • Spring - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 • Screw - Rigid 0.14 ... 4 mm² - Flexible 0.14 ... 2.5 mm² - AWG 26-14 8WH2 103-3BF07 50 units I201_12675 8WH2 103-3BF07 * You can order this quantity or a multiple thereof. 4/19 8WH2 Spring-Loaded Terminals 8WH hybrid through-type terminals Version Order No. MOQ* Terminal size 4 mm² 4 8WH2 103-2BG00 Hybrid through-type terminals, terminal size 4 mm² • Terminal width 6.2 mm • IEC 60947-7-1 • Spring - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 - I = 32 A - The total current through all connected conductors must not exceed the max. load current - U = 800 V • Screw - Rigid 0.14 ... 6 mm² - Flexible 0.14 ... 4 mm² - AWG 26-10 - I = 32 A - U = 800 V Versions 8WH2 103-3BG07 • Gray • Blue 8WH2 103-2BG00 8WH2 103-2BG01 50 units 50 units PE hybrid through-type terminals, terminal size 4 mm² • Terminal width 6.2 mm • IEC 60947-7-2 • Spring - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 • Screw - Rigid 0.14 ... 6 mm² - Flexible 0.14 ... 4 mm² - AWG 26-10 8WH2 103-3BG07 50 units 8WH9 000-2HA00 8WH9 003-2HA00 50 units 50 units I201_12676 8WH2 103-3BG07 Accessories Covers Gray Versions • For terminal size 2.5 mm² and three clamping points • For terminal size 4 mm² and three clamping points 8WH9 000-2HA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/20 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH fuse terminals ■ Overview Fuse terminals for blade-type fuses The fuse terminals for blade-type fuses accommodate bladetype fuses according to ISO/DIS 8820 / DIN 72581-3. Terminals with LED display are available for fast fault diagnosis "at a glance". Fuse terminals for G fuse links Fuse terminals perform two important tasks in connected electrical systems. Firstly, they act as a fuse carrier and, secondly, as a potential distributor. The full-length bridge shaft enables uninterrupted bridging between the through-type terminals and the fuse terminals. Fuse terminals for G fuse links are available for standardized electrical fuse formats 5 × 20 mm and 6.3 × 32 mm (inch fuse) – and are optionally available with LED display to signal a blown fuse. A label can be snapped on to the middle of the terminal at the front. Further labels can also be mounted flat on the side of the terminals. ■ Technical specifications 8WH2 000-1AG08 8WH2 000-1BG28 8WH2 000-1BG38 8WH2 000-1GG08 8WH2 000-1JG38 8WH2 000-1JG68 8WH2 000-1MG08 8WH2 000-1HG08 8WH2 000-1NG38 8WH2 000-1NG68 8WH2 000-1RG08 Dimensions • Width/length in mm • Height (NS 35/7.5 / NS 35/15) in mm 8.2 / 86.5 43.5 / 51 6.2 / 61.5 62.5 / 70 8.2 / 76.5 69 / 76.5 Technical specifications acc. to IEC/DIN VDE • Fuse type ISO/DIS 8820 / DIN 72581-3 / dimensions / in mm • Maximum current for single arrangement in A C 30 G / 5 × 20 3.3 G / 6.3 × 32 10 -- 250 400 --- 1.6 1.6 --- 4 2.5 • Imax in A • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group -6/3 III / I 6.3 4/3 10 6/3 Connection capacities • Flexible with end sleeve without/with plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 4 / 0.25 ... 4 0.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A4 A3 A4 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 600 / 30 / 24-10 -- 300 / 6.3 / 24-10 300 / 10 / 24-10 Max. power loss at 23 °C acc. to IEC 60647-7-3 in W1) • U in V • Overload protection - Individually in W - As group in W • Without short-circuit protection - Individually in W - As group in W 1) Please note: The G fuse holders must be selected according to the maximum power loss (heat dissipation) of the G fuse links. Depending on the application and method of installation, the heat rise conditions in closed fuse holders must be tested. Higher ambient temperatures represent an additional load for the fuse links. A shift in rated current should therefore be taken into account in such applications. When selecting G fuse links, make sure that they do not exceed the specified maximum power loss. For specification details, contact the fuse manufacturer. 4/21 4 8WH2 Spring-Loaded Terminals 8WH fuse terminals ■ Selection and ordering data Version 4 Order No. MOQ* Terminal size 4 mm² 8WH2 000-1AG08 Fuse terminals, terminal size 4 mm², for blade-type fuses acc. to ISO/DIS8820/DIN72581-3 • Terminal width 8.2 mm • CUUS • Connection data - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 - I = 30 A - U = 400 V • Enclosed at both ends Versions 8WH2 000-1BG28 • Without LED display • LED display 12 V • LED display 24 V 8WH2 000-1AG08 8WH2 000-1BG28 8WH2 000-1BG38 50 units 50 units 50 units 8WH2 000-1GG08 8WH2 000-1JG38 8WH2 000-1JG68 8WH2 000-1MG08 50 units 50 units 50 units 50 units 8WH2 000-1HG08 8WH2 000-1RG08 50 units 50 units 8WH9 070-0AA00 8WH9 070-0KA00 50 units 50 units I201_12681 8WH2 000-1BG28 8WH2 000-1GG08 Fuse terminals, terminal size 4 mm², for 5 x 20 mm G fuse links • Terminal width 6.2 mm • CUUS • IEC 60947-7-3 • With fuse - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - Imax = 6.3 A, only short-circuit protection, single 4 W, group 2.5 W - U = 250 V, overload protection, single 4 W, group 1.6 W • As isolating terminal - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 6.3 A, U = 250 V • Enclosed at both ends Versions • • • • Without LED display LED display 15 to 30 V LED display 30 to 60 V LED display 110 to 250 V 8WH2 000-1JG38 8WH2 000-1HG08 Fuse terminals, terminal size 4 mm², for G fuse links 6.3 x 32 mm (inch fuses) • Terminal width 8.2 mm • CUUS • IEC 60947-7-3 • With fuse - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 10 A, - U = 400 V - Current and voltage are determined by the fitted fuse or the selected LED display • As isolating terminal - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 10 A, U = 400 V • Enclosed at both ends Versions • Without LED display • With LED display 100 V to 250 V Accessories Compartment partitions, for terminal sizes 1.5 and 4 mm² Versions • Two clamping points • Three clamping points (inch fuse) 8WH9 070-0AA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/22 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH isolating blade terminals ■ Overview Through-type terminals with isolating blade capability are the most commonly used terminal types in measuring and control technology. The isolating blade terminals with nominal cross-section of 2.5 mm² are characterized in particular by their slim design of 5.2 mm and their high current-carrying capacity of 16 A. In addition the terminals provide a test tap parallel to the isolation point for 2.3 mm test plugs. Potential distributors can be conveniently assembled using connecting combs. Terminals with three and four clamping points are available for multi-conductor connection. With their compact design these terminals can also be used in small terminal boxes and their front connection arrangement enables user-friendly wiring. The isolating blade is secured to the terminal so that it cannot be lost. A label can be snapped on to the middle of the terminal at the front. Further labels can also be mounted flat on the side of the terminals. ■ Technical specifications Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Maximum data // rated data in A / mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 8WH2 000-6CF00 8WH2 500-6CF00 8WH2 003-6CF00 8WH2 004-6CF00 8WH2 000-6CG00 5.2 / 60.5 / 2.2 36.5 / 44 5.2 / 51 / 2.2 43 / 50.5 5.2 / 72 / 2.2 36.5 / 44 5.2 / 84 / 2.2 6.2 / 61.5 / -- 16 / 4 16 / 6 -6/3 III / I Connection capacities • Flexible with end sleeve, with plastic 0.25... 2.5 sleeve in mm² • Flexible with end sleeve, without plastic 0.25 ... 2.5 sleeve in mm² • Flexible with two-wire connection end 0.5 sleeve, with plastic sleeve in mm² Stripped length in mm 10 Plug gauge (IEC 60947-1) A4 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG 600 / 16 / 26-12 - CSA: in V/A / AWG -- 0.25 ... 4 0.25 ... 4 A3 A4 600 / 16 / 24-12 600 / 16 / 26-12 A3 300 / 6.3 / 24-10 4/23 4 8WH2 Spring-Loaded Terminals 8WH isolating blade terminals ■ Selection and ordering data Version 4 Order No. MOQ* Terminal size 2.5 mm² 8WH2 000-6CF00 I201_12684 8WH2 000-6CF00 Isolating blade terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 16 A - U = 400 V • For 3 and 4 clamping points: - Rigid 0.14 ... 4 mm² - Flexible 0.14 ... 2.5 mm² - AWG 26-14 Versions • Gray - Two clamping points - Three clamping points - Four clamping points 8WH2 000-6CF00 8WH2 003-6CF00 8WH2 004-6CF00 50 units 50 units 50 units 8WH2 000-6CG00 50 units 8WH9 070-0AA00 8WH9 070-0GA00 8WH9 070-0HA00 50 units 50 units 50 units • For two clamping points • For three clamping points • For four clamping points 8WH9 000-2GA00 8WH9 000-4GA00 8WH9 000-5GA00 50 units 50 units 50 units Cover segments, for terminal size 2.5 mm² and three or four clamping points 8WH9 000-0GA00 10 units Note 8WH2 003-6CF00 On terminals with three and four clamping points, the total current through all connected conductors must not exceed the max. load current. I201 12685 8WH2 003-6CF00 8WH2 004-6CF00 I201_12686 8WH2 004-6CF00 8WH2 000-6CG00 Isolating blade terminals, size 4mm², two clamping points • Gray • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm², flexible 0.08 ... 4 mm², AWG 28-10 - I = 16 A, U = 400 V • Enclosed at both ends Accessories Compartment partitions, for terminal size 1.5 to 4 mm² Versions • Two clamping points • Three clamping points • Four clamping points 8WH9 070-0AA00 Covers, for terminal sizes 1.5 ... 2.5 mm² Versions 88WH9 000-2GA00 8WH9 000-0GA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/24 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH isolating terminals ■ Overview The isolating terminals are available with the same contour as the isolating blade terminals. The terminals excel with their narrow width of only 5.2 mm and their high current load rating of 16 A. There is a test option for 2.3 mm test plugs at both ends of the isolating point. The 6.2 mm wide isolating terminal with terminal size 4 mm² is a base terminal for accommodating: • Isolating plugs • Through-type connectors • Fused connectors • Component connectors A label can be snapped on to the middle of the terminal at the front. Further labels can also be mounted flat on the side of the terminals. ■ Technical specifications Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 8WH2 000-6AF00 8WH2 500-6AF00 8WH2 003-6AF00 8WH2 004-6AF00 8WH2 000-6AG00 5.2 / 60.5 / 2.2 36.5 / 44 5.2 / 51 / 2.2 43 / 50.5 5.2 / 72 / 2.2 36.5 / 44 5.5 / 84 / 2.2 6.2 / 61.5 / -- 16 / 4 6/3 16 / 6 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 • Flexible with end sleeve, without plastic sleeve in mm² 0.25 ... 2.5 0.5 • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 300 / 16 / 26-12 -- 0.25 ... 4 0.25 ... 4 A4 300 / 16 / 24-12 300 / 16 / 26-12 300 / 6.3 / 24-10 4/25 4 8WH2 Spring-Loaded Terminals 8WH isolating terminals ■ Selection and ordering data Version 4 Order No. MOQ* Terminal size 2.5 mm² 8WH2 000-6AF00 Isolating terminals, terminal size 2.5 mm² • Gray • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - Current and voltage are determined by the fitted plug - I = 16 A - U = 400 V Versions I201_12682 8WH2 000-6AF00 • Two clamping points • Three clamping points • Four clamping points 8WH2 000-6AF00 8WH2 003-6AF00 8WH2 004-6AF00 50 units 50 units 50 units Isolating terminals, terminal size 4 mm², two clamping points • Gray • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 - Current and voltage are determined by the fitted plug - I = 16 A - U = 400 V • Enclosed at both ends 8WH2 000-6AG00 50 units 8WH9 070-0GA00 8WH9 070-0HA00 50 units 50 units 8WH9 070-0AA00 50 units • For terminal size 1.5 ... 2.5 mm² and two clamping points • For terminal size 2.5 mm² and three clamping points • For terminal size 2.5 mm² and four clamping points 8WH9 000-2GA00 8WH9 000-4GA00 8WH9 000-5GA00 50 units 50 units 50 units Cover segments, for terminal size 1.5 mm² and 2.5 mm² and three or four clamping points Gray 8WH9 000-0GA00 10 units 8WH2 003-6AF00 8WH2 004-6AF00 Terminal size 4 mm² 8WH2 000-6AG00 I201_12682 8WH2 000-6AG00 Accessories Compartment partitions Versions 8WH9 070-0GA00 • For terminal size 2.5 mm² - For three clamping points - For four clamping points • For terminal size 4 mm² - For two clamping points Covers Gray Versions 8WH9 000-2GA00 8WH9 000-0GA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/26 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH two-tier terminals ■ Overview Standard two-tier terminals With the two voltage levels routed through two separate tiers, the two-tier terminals require 50% less space than equivalent singletier terminals. To implement a wide range of wiring tasks, connecting combs can be fitted to both tiers of the spring-loaded terminal series. Facilities for inscription are provided at each clamping point. PE/ground conductor function Perfect mechanical and electrical contact with the support rail is provided by simply snapping the terminals onto the rail. The PE two-tier terminals meet all the requirements of IEC 60947-7-2: • Low contact resistance • Stainless clamping points • Green-yellow enclosure • Additional inscription options. PE/L and PE/N types The PE/L and PE/N types provide a PE/ground contact to the support rail in the lower tier. The upper tier is designed as a through-type tier. Color coding of the PE and neutral tiers enables clear and unambiguous distribution of the potential. The clamping points of two-tier terminals can be inscribed with flat labels. ■ Technical specifications 8WH2 020-0AE00 8WH2 020-0AE01 8WH2 025-0AE00 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Maximum data / rated data in A / mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 8WH0 020-0CE07 4.2 / 67.5 / 2.2 47.5 / 55 17.5 / 1.5 -6/3 -- 8WH2 020-0AF00 8WH2 020-0AF01 8WH2 025-0AF00 8WH2 023-0AF00 8WH2 023-0AF01 8WH2 022-0AF00 8WH2 020-0CF07 5.2 / 67.5 / 2.2 5.2 / 91.5 / 2.2 5.2 / 67.5 / 2.2 26 / 4 -26 / 4 // 22 / 2.5 --- 300 / 20 / 26-12 -- / -- / 26-12 -- / -- / 26-12 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² 0.25 ... 1.5 0.25 ... 1.5 • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with 0.5 plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A1 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 300 / 15 / 26-14 300 / 15 / 26-14 -- / -- / 26-14 -- / -- / 26-14 600 / 20 / 26-12 -- Support rails/protective conductor busbars -- See section "Support rails" on page 1/3 -- A3 See section "Support rails" on page 1/3 4/27 4 8WH2 Spring-Loaded Terminals 8WH two-tier terminals Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm 4 8WH2 023-0CF07 8WH2 020-4AF00 5.2 / 91.5 / 2.2 47.5 / 55 5.2 / 67.5 / 2.2 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² -• Rated impulse withstand voltage in kV / pollution degree 6 / 3 III / I • Overvoltage category / molded plastic group 32 / 4 Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG -- / -- / 26-12 -- / -- / 26-12 300 / 20 / 26-12 -- See section "Support rails" on page 1/3 -- Support rails/protective conductor busbars Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm -- 8WH2 020-4CF00 8WH2 020-0AG00 8WH2 020- 8WH2 020-0CG07 0AG01 8WH2 025-0AG00 5.2 / 67.5 / 2.2 47.5 / 55 6.2 / 83.5 / 2.2 6.2 / 83.5 / 2.2 32 / 6 -- 0.25 ... 4 0.25 ... 4 0.5 ... 1 0.25 ... 4 0.25 ... 4 0.5 ... 1 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² 26 / 4 • Rated impulse withstand voltage in kV / pollution degree 6 / 3 III / I • Overvoltage category / molded plastic group Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in AWG - CSA: in AWG 300 / 20 / 26-12 -- / -- / 26-12 Support rails/protective conductor busbars -- 4/28 8WH2 020-4BF00 A4 300 / 30 / 20-10 20-10 20-10 See section "Support rails" on page 1/3 8WH2 Spring-Loaded Terminals 8WH two-tier terminals ■ Selection and ordering data Version Order No. MOQ* 4 Terminal size 1.5 mm² 8WH2 020-0AE00 Two-tier terminals, terminal size 1.5 mm² • Terminal width 4.2 mm • CUUS, s • IEC 60947-7-1 - Rigid 0.08 ... 1.5 mm² - Flexible 0.08 ... 1.5 mm² - AWG 28-16 - I = 17.5 A - The total current through all connected conductors must not exceed the max. load current - U = 500 V Versions • Gray - Without equipotential bonding, 2-pole s - With equipotential bonding, 1-pole • Blue, 2-pole 8WH2 020-0AE00 8WH2 025-0AE00 8WH2 020-0AE01 50 units 50 units 50 units 8WH2 020-0CE07 50 units I201_12691 8WH2 020-0AE00 I201_14017 8WH2 025-0AE00 8WH2 020-0CE07 PE two-tier terminals, terminal size 1.5 mm² • Terminal width 4.2 mm • CUUS, s • IEC 60947-7-1 - Rigid 0.08 ... 1.5 mm² - Flexible 0.08 ... 1.5 mm² - AWG 28-16 • Green/yellow I201_12688 8WH2 020-0CE07 * You can order this quantity or a multiple thereof. 4/29 8WH2 Spring-Loaded Terminals 8WH two-tier terminals Version Order No. MOQ* Terminal size 2.5 mm² 4 8WH2 020-0AF00 Two-tier terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A - The total current through all connected conductors must not exceed the max. load current - U = 500 V Versions I201_12691 8WH2 020-0AF00 • Gray - Without equipotential bonding, 2-pole - With equipotential bonding, 1-pole • Blue - Without equipotential bonding, 2-pole - With equipotential bonding, 1-pole 8WH2 020-0AF00 8WH2 025-0AF00 50 units 50 units 8WH2 020-0AF01 8WH2 025-0AF01 50 units 50 units 8WH2 023-0AF00 8WH2 022-0AF00 8WH2 023-0AF01 50 units 50 units 50 units 8WH2 020-4AF00 50 units I201_14017 8WH2 025-0AF00 8WH2 023-0AF00 Two-tier terminals, terminal size 2.5 mm², three clamping points on one level • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A - The total current through all connected conductors must not exceed the max. load current - U = 500 V Versions I201_12691 8WH2 023-0AF00 • Gray - Without equipotential bonding, 2-pole - With equipotential bonding, 1-pole • Blue, 2-pole I201_14017 8WH2 022-0AF00 8WH2 020-4AF00 Two-tier terminals, terminal size 2.5 mm², L at top and PE at bottom • Gray • Terminal width 5.2 mm • CUUS • DIN VDE 0611 and IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 32 A - U = 500 V I201_12689 8WH2 020-4AF00 4/30 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH two-tier terminals 8WH2 020-4BF00 Version Order No. MOQ* Two-tier terminals, terminal size 2.5 mm², N at top and PE at bottom • Gray • Terminal width 5.2 mm • DIN VDE 0611 and IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 32 A - U = 500 V 8WH2 020-4BF00 Two-tier terminals, terminal size 2.5 mm², N at top and L at bottom • Gray • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A - U = 500 V 8WH2 020-4CF00 50 units PE two-tier terminals, terminal size 2.5 mm², two clamping points on one level • Terminal width 5.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 • Green/yellow 8WH2 020-0CF07 50 units PE two-tier terminals, terminal size 2.5 mm², three clamping points on one level • Terminal width 5.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 • Green/yellow 8WH2 023-0CF07 50 units 50 units 4 I201_12690 8WH2 020-4BF00 8WH2 020-4CF00 I201_12691 8WH2 020-4CF00 8WH2 020-0CF07 I201_12692 8WH2 020-0CF07 8WH2 023-0CF07 I201_12693 8WH2 023-0CF07 * You can order this quantity or a multiple thereof. 4/31 8WH2 Spring-Loaded Terminals 8WH two-tier terminals Version Order No. MOQ* Terminal size 4 mm² 4 8WH2 020-0AG00 Two-tier terminals, terminal size 4 mm² • Terminal width 6.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 - I = 32 A - The total current through all connected conductors must not exceed the max. load current - U = 500 V Versions I201_12691 • Gray - Without equipotential bonding, 2-pole - With equipotential bonding, 1-pole • Blue, 2-pole 8WH2 020-0AG00 8WH2 025-0AG00 8WH2 020-0AG01 50 units 50 units 50 units PE two-tier terminals, terminal size 4 mm² • Terminal width 6.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 • Green/yellow 8WH2 020-0CG07 50 units Compartment partitions, for terminal size 1.5 to 4 mm² • For visual and electrical separation of terminal groups • 2 mm thick 8WH9 070-0BA00 50 units 8WH9 000-1VA00 8WH9 000-2VA00 8WH9 003-1VA00 50 units 50 units 50 units 8WH2 020-0AG00 I201_14017 8WH2 025-0AG00 8WH2 020-0CG07 I201_12694 8WH2 020-0CG07 Accessories 8WH9 070-0BA00 Covers Gray Versions 8WH9 000-1VA00 • For terminal size 1.5 ... 2.5 mm² • For terminal size 2.5 mm² and three clamping points • For terminal size 4 mm² Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/32 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH three-tier terminals ■ Overview Our three-tier terminals offer three feed-through levels in a slim 5.2 mm terminal enclosure. They enable high wiring density – ideal for switchboards where space is at a premium. With one bridge shaft per tier, these terminal blocks are ideal for use as compact potential distributors or initiator terminals. All six clamping points are interconnected on the equipotential bonding versions. The three-tier terminal range is rounded off with a PE terminal with the same contour. Inscription Each tier of three-tier terminals can be inscribed with flat labels. If a label holder is used, the labels can be inserted at the front. ■ Benefits • Three feed-through levels with minimum footprint • Comprehensive range of inscription options • Matching accessories for 8WH terminal range • One bridge shaft per tier • Label holder is inserted. ■ Technical specifications 8WH2 030-0AF00 8WH2 030-0AF01 8WH2 035-0AF00 8WH2 035-0CF07 8WH2 030-4EF00 8WH2 030-4HF00 Dimensions • Width/length in mm • Height (TS 35/7.5 / TS 35/15 / TS 32) in mm 5.2 / 99.5 58 / 65.5 5.2 / 99.5 58 / 65.5 5.2 / 99.5 58 / 65.5 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 28 / 4 6/3 III / I -6/3 III / I 28 / 4 6/3 III / I Connection capacities • Flexible with end sleeve without / with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with TWIN end sleeve with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 0.25 ... 2.5 0.25 ... 2.5 0.5 0.25 ... 2.5 0.25 ... 2.5 0.5 Stripped length in mm 10 10 10 Plug gauge (IEC 60947-1) A3 A3 A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 PA V0 PA V0 Approval data (UL/CUR and CSA) • Rated voltage / rated current / conductor sizes - UL/CUR: V/A/AWG - CSA: V/A/AWG 600 / 20 / 26-12 -- -- / -- / 24-12 -- 300 / 20 / 26-12 -- ■ Selection and ordering data Version Order No. MOQ* Terminal size 2.5 mm² 8WH2 030-0AF00 Three-tier terminals, terminal size 2.5 mm² • Enclosed at both ends • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08-4 mm² - Flexible 0.08-2.5 mm² - AWG 28-12 - I = 28 A - U = 500 V Versions I201_13974 • Gray • Blue 8WH2 030-0AF00 8WH2 030-0AF01 50 units 50 units 8WH2 030-0AF00 * You can order this quantity or a multiple thereof. 4/33 4 8WH2 Spring-Loaded Terminals 8WH three-tier terminals 4 8WH2 035-0AF00 Version Order No. MOQ* Three-tier terminals, with equipotential bonding, terminal size 2.5 mm² • Enclosed at both ends • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 - Rigid 0.08-4 mm² - Flexible 0.08-2.5 mm² - AWG 28-12 - I = 28 A - U = 500 V 8WH2 035-0AF00 50 units Three-tier terminals, "PE/L/N", terminal size 2.5 mm² • Enclosed at both ends • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 + IEC 60947-7-2 - Rigid 0.08-4 mm² - Flexible 0.08-2.5 mm² - AWG 28-12 8WH2 030-4EF00 50 units Three-tier terminals, "PE/L/L", terminal size 2.5 mm² • Enclosed at both ends • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 + IEC 60947-7-2 - Rigid 0.08-4 mm² - Flexible 0.08-2.5 mm² - AWG 28-12 - I = 28 A - U = 500 V 8WH2 030-4HF00 50 units PE three-tier terminals, terminal size 2.5 mm² • Enclosed at both ends • Terminal width 5.2 mm • CUUS • IEC 60947-7-2 - Rigid 0.08-4 mm² - Flexible 0.08-2.5 mm² - AWG 28-12 8WH2 035-0CF07 50 units Covers for three-tier terminals 8WH9 000-1GD00 50 units Label holders, for three-tier terminals 8WH9 060-4BA00 100 units Note I201_13975 8WH2 035-0AF00 8WH2 030-4EF00 The total current through all connected conductors must not exceed the max. load current. I201_13976 8WH2 030-4EF00 8WH2 030-4HF00 I201_13976 8WH2 030-4HF00 8WH2 035-0CF07 I201_13978 8WH2 035-0CF07 Accessories 8WH9 000-1GD00 8WH9 060-4BA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/34 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH four-tier motor terminals ■ Overview Terminal size 2.5 mm² The four-tier motor terminals with terminal size 2.5 mm² are ideal for the compact wiring of AC loads. They have three throughlevels and one PE connection which is contacted by simply snapping it onto the mounting rail. No cross-bridging option. Terminal size 4 mm² Like the 2.5 mm² version, the four-tier motor terminal with 4 mm² also allows the wiring of three phases and the PE in a single terminal. This terminal is enclosed at both ends. No cross-bridging option. Integrated PE/ground conductor function PE contact with the support rail is made by simply snapping the terminal onto the rail. This makes the four-tier motor terminals with terminal size 4 mm² ideal for the space-saving wiring of AC motors. Inscription Each clamping point has a facility for inscription and a test option for 2.3 mm test plugs. There is also sufficient space to make large marking with labels in the middle of the terminal. Labels can be mounted flat at the side of the terminals by simply snapping on ■ Technical specifications 8WH2 040-4LF00 8WH2 040-4LG00 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm 5.2 / 98.5 / 2.2 73.5 / 81 6.2 / 101 / -83.5 / 91 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 26 / 4 8/3 III / I 32 / 6 Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 -- 0.25 ... 4 0.25 ... 4 0.5 ... 1 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG -- / -- / 26-12 -- A4 -600 / 30 / 28-10 4/35 4 8WH2 Spring-Loaded Terminals 8WH four-tier motor terminals ■ Selection and ordering data 4 Version Order No. MOQ* Four-tier motor terminals, terminal size 2.5 mm² • Terminal width 5.2 mm • CUUS • IEC 60947-7-1 and IEC 60947-7-2 - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A - U = 800 V 8WH2 040-4LF00 50 units Four-tier motor terminals, terminal size 4 mm² • Terminal width 6.2 mm • CUUS s • IEC 60947-7-1 and IEC 60947-7-2 - Rigid 0.08 ... 6 mm² - Flexible 0.08 ... 4 mm² - AWG 28-10 - I = 32 A - U = 800 V • Enclosed at both ends 8WH2 040-4LG00 50 units Covers For four-tier motor terminals, terminal size 2.5 mm² 8WH9 000-1GE00 50 units Terminal size 2.5 mm² 8WH2 040-4LF00 8WH2 040-4LF00 I201 13468 Terminal size 4 mm² 8WH2 040-4LG00 8WH2 040-4LG00 I201_13468 Accessories 8WH2 040-4LG00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/36 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH diode terminals ■ Overview Diode terminals with a nominal cross-section of 2.5 mm² and a mounting width of just 5.2 mm can be used to implement many different wiring tasks. The diode is soldered in from left to right or vice versa as required. A label can be snapped on to the middle of each terminal at the front. Further labels can also be mounted flat on the side of the terminals. ■ Technical specifications 8WH2 003-5DF00 8WH2 003-5CF00 Dimensions • Width/length/cover width in mm • Height HV-M ... (NS 35/7.5 / NS 35/15) in mm 5.5 / 60.5 / 2.2 36.5 / 44 Technical specifications acc. to IEC/DIN VDE • Max. load current in A / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group Determined by the diode / 4 4/3 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: V/A/AWG - CSA: V/A/AWG 600 / 20 / 26-12 -- 4/37 4 8WH2 Spring-Loaded Terminals 8WH diode terminals ■ Selection and ordering data Version 4 Order No. MOQ* Terminal size 2.5 mm² 8WH2 003-5DF00 Diode terminals, terminal size 2.5 mm², with three clamping points • Uninterrupted limiting current: 0.5 A • Blocking voltage: 1300 V • Terminal width 5.2 mm • CUUS • Connection data - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = the maximum current is determined by the diode - U = 500 V • With integrated diode • Integrated: diode 1N 4007 Versions I201_12712 8WH2 003-5DF00 • Let-through from left to right • Let-through from right to left 8WH2 003-5DF00 8WH2 003-5CF00 50 units 50 units Compartment partitions, for terminal size 1.5 to 4 mm² and three clamping points 8WH9 070-0GA00 50 units Covers, for terminal size 1.5 ... 2.5 mm² and three clamping points 8WH9 000-4GA00 50 units Cover segments, for terminal size 1.5 and 2.5 mm² and three clamping points 8WH9 000-0GA00 10 units I201_12713 8WH2 003-5CF00 Accessories 8WH9 070-0GA00 8WH9 000-4GA00 8WH9 000-0GA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/38 * You can order this quantity or a multiple thereof. 8WH2 Spring-Loaded Terminals 8WH two-tier diode terminals ■ Overview Two-tier diode terminals can be used together with different versions to implement many different wiring tasks. The following circuits are possible in the tightest spaces: • Freewheel diode circuits • Lamp test circuits • Signaling and fault signaling circuits. 4 The clamping points of two-tier terminals can be inscribed with flat labels. ■ Technical specifications 8WH2 020- 5AF00, 5DF00, 5BF00 Dimensions • Width/length/cover width in mm • Height (NS 35/7.5 / NS 35/15) in mm 5.2 / 67.5 / 2.2 47.5 / 55 Technical specifications acc. to IEC/DIN VDE • Max. load current in A (not via diodes) / cross-section in mm² • Rated impulse withstand voltage in kV / pollution degree • Overvoltage category / molded plastic group 26 / 4 4/3 III / I Connection capacities • Flexible with end sleeve, with plastic sleeve in mm² • Flexible with end sleeve, without plastic sleeve in mm² • Flexible with two-wire connection end sleeve, with plastic sleeve in mm² 0.25 ... 2.5 0.25 ... 2.5 0.5 Stripped length in mm 10 Plug gauge (IEC 60947-1) A3 Molded plastic type • Flammability class acc. to UL 94 PA V0 Approval data (UL/cUL and CSA) • Rated voltage / rated current / conductor sizes - UL/cUL: in V/A / AWG - CSA: in V/A / AWG 300 / 20 / 26-12 300 / 20 / 26-12 5HF00, 5FF00, 5KF00, 5EF00, 5GF00 5JF30, 5JF80 ■ Selection and ordering data Version Terminal size 2.5 mm² MOQ* General data CUUS Two-tier diode terminals, size 2.5 mm², with one diode • Terminal width 5.2 mm • Connection data - Rigid 0.08 ... 4 mm², flexible 0.08 ... 2.5 mm², AWG 28-12 - I = 26 A, U = 500 V • Maximum current determined by diode • Integrated: diode 1N 4007 - Blocking voltage: 1300 V, uninterrupted limiting current: 0.5 A Circuit diagram Versions Let-through from top to bottom 8WH2 020-5AF00 50 units Let-through from bottom left to top right 8WH2 020-5DF00 50 units Let-through from bottom to top 8WH2 020-5BF00 50 units I201_12716 I201_12715 I201_12714 8WH2 020-5AF00 Order No. * You can order this quantity or a multiple thereof. 4/39 8WH2 Spring-Loaded Terminals 8WH two-tier diode terminals Version 4 8WH2 020-5HF00 Order No. MOQ* Two-tier-diode terminals, terminal size 2.5 mm², with two diodes • Terminal width 5.2 mm • Connection data - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A, U = 500 V • Maximum current determined by diode • Integrated: diode 1N 4007 - Blocking voltage: 1300 V - Uninterrupted limiting current: 0.5 A Circuit diagram Versions 8WH2 020-5HF00 50 units Let-through from top to bottom left and from bottom right to bottom left 8WH2 020-5KF00 50 units Let-through from bottom left to top and from bottom left to bottom right 8WH2 020-5EF00 50 units Let-through from bottom left to top and from bottom right to top 8WH2 020-5GF00 50 units • 15 to 30 V DC/2.5 to 7.5 A 8WH2 020-5JF30 50 units • 110 to 230 V AC/DC / 0.5 to 1.0 A (glow lamp) 8WH2 020-5JF80 50 units Compartment partitions, for terminal size 1.5 to 4 mm² 8WH9 070-0BA00 50 units Covers, for terminal size 1.5 and 2.5 mm² 8WH9 000-1VA00 50 units I201_13467 I201_13466 I201_12718 I201_12717 Let-through from top to bottom left and from top to bottom right 8WH2 020-5JF30 Two-tier diode terminals, terminal size 2.5 mm², with LED • Terminal width 5.2 mm • Connection data - Rigid 0.08 ... 4 mm² - Flexible 0.08 ... 2.5 mm² - AWG 28-12 - I = 26 A - U = 500 V Versions 8WH2 020-5JF30 Accessories 8WH9 070-0BA00 8WH9 000-1VA00 Note: For general accessories for 8WH terminal blocks, see chapter 8. 4/40 * You can order this quantity or a multiple thereof.