Communications and Software

8
© Siemens AG 2015
Communication and Software
8/2
8/3
8/6
8/7
8/8
8/9
8/11
8/21
8/22
Communication
HART protocol
WirelessHART
PROFIBUS
FOUNDATION Fieldbus
WirelessHART Communication
Communication blocks
SITRANS MDS Maintenance Diagnostic Station
Software
SIMATIC PDM Process Device Manager
SITRANS DTM
SITRANS Library
Siemens FI 01 · 2015 US Edition
© Siemens AG 2015
Communication and Software
Communication
HART protocol
■ Overview
■ Integration
HART is a widely used communication standard for field
devices. Specification of HART devices takes place through the
HCF (HART Communication Foundation).
The HART standard expands the analog 4 to 20 mA signal for
modulated, industry-proven, digital signal transmission.
Measuring instruments for pressure
SITRANS P DS III
SITRANS P300
■ Benefits
SITRANS P500
• Service-proven analog measured value transmission
• Simultaneous digital communication with bidirectional data
transmission
• Possibility of transmitting several measured variables from
one field device (e.g. diagnosis, maintenance and process
data)
• Connection to higher-level systems such as PROFIBUS DP
• Easy installation and startup
Use in conjunction with SIMATIC PDM
• Cross-vendor operation of all HART devices by means of standardized parameter records
• HART field devices that are described by HART DD are integrated in SIMATIC PDM through the HCF catalog. HART DD
(Device Description) is standardized in SIMATIC PDM, multivendor and very widely used. Other HART field devices are integrated in SIMATIC PDM through EDD (Electronic Device Description)
• Easy operation and startup of field devices, also in
hard-to-reach locations
• Expanded diagnosis, evaluation and logging functions
■ Application
8
Siemens field devices for process automation which are listed in
this catalog and can be controlled using HART:
These devices can be connected in different ways:
• Using the distributed I/O system
- SIMATIC ET 200M with the HART modules
- SIMATIC ET 200iSP with the HART modules
or with analog modules 4 to 20 mA and a HART handheld
communicator
• Using a HART modem, with which a point-to-point connection
is established between the PC or engineering station and the
HART device
• Using HART multiplexers, which are contained in the HART
server of the HCF
Measuring instruments for temperature
SITRANS TF
SITRANS TH300
SITRANS TR300
SITRANS TW
Flowmeters
SITRANS F M MAG 5000
SITRANS F M MAG 6000 19" / IP67
SITRANS F M MAG 6000 I / I Ex
SITRANS F M Transmag 2
SITRANS F C MASS 6000 19" / IP67 / Ex d
SITRANS F C FCT030
SITRANS FUS060
SITRANS FX300
Measuring instruments for level
Pointek CLS500
SITRANS Probe LR
SITRANS Probe LU
SITRANS LUT400
SITRANS LR200
SITRANS LR250
SITRANS LR260
SITRANS LR400
SITRANS LR460
SITRANS LR560
SITRANS LC500
Positioners
SIPART PS2
Power supply units and isolation amplifiers
SITRANS I
■ Selection and Ordering data
Article No.
HART modem
With USB connection
8/2
Siemens FI 01 · 2015 US Edition
7MF4997-1DB
© Siemens AG 2015
Communication and Software
Communication
WirelessHART
WirelessHART is the first international industry standard for wireless communication at field level in the area of process automation. Hence this is the first time users are provided with a standard for wireless communication at field level which ensures the
interoperability of instruments and components from different
manufacturers.
■ Benefits
WirelessHART enables access to the following:
• Measuring and control values
• Parameters
■ Design
This section introduces the application types described in the
previous section in greater detail.
The figure below shows a typical situation for the first application
type.
SITRANS
MDS
OS
Industrial Ethernet
Controller without
HART support
of field devices with HART interface. These usually include pressure, temperature, level or flow transmitters or actuators.
WirelessHART allows for the following:
• wireless transmission of measured values and their status
• wireless parameterization and diagnosis of field devices
The WirelessHART adapter can be used to enable field devices
with HART interfaces (that are designed for wired communication) for wireless communication. This allows users to continue
using their proven devices while benefiting from and participate
in addition in advantages offered by wireless communication.
SITRANS
AW200
4 –20 mA
IWLAN
IEEE802.11
4 –20 mA
Wireless
HART
■ Application
Looking at the large number of possible applications and configurations, we generally differentiate between two application
types.
Background for the first type is the fact that according to estimates forwarded by the HART Communication Foundation
(HCF), approximately 85 % of the over 30 million HART devices
in operation are used in an environment where only the 4 to
20 mA interface rather than the HART interface of the device is
used on a system level. Generally, data on the device can only
be read on site. This is of particular disadvantage with devices
that contain self-diagnostic functions - that’s what we call
"stranded diagnosis".
In these cases, a WirelessHART adapter can offer assistance.
Connected to the 4 to 20 mA loop, it allows central access to the
device based on wireless communication. It does not affect process control systems which continue to receive the measured
value using the 4 to 20 mA loop.
Central access is enabled through a diagnostic station with
SIMATIC PDM and SITRANS MDS software.
Main advantages:
• Increases the availability of the plant
• Increases plant transparency
• Reduces costs due to employing a predictive rather than preventative maintenance concept
• Reduces travel time in larger systems based on central access to field instrumentation
Industrial
Ethernet
Remote I/O station
w/o HART support
4 –20 mA
IE/WSNPA LINK
PROFIBUS
■ Overview
The adapter is connected to the 4 to 20 mA loop, which is used
to transmit the measured value to the control system, or transmit
the setpoint to an actuator. The existing control system is not affected by the WirelessHART adapter.
The data, in particular diagnostic data from the devices is transmitted to the IE/WSN-PA LINK via the connected adapter and the
WirelessHART network. The link provides this data to a diagnostic and maintenance station with installed SITRANS MDS software and SIMATIC PDM via an industrial Ethernet. Industrial
wireless LAN can be used to save on the installation costs required for Ethernet wiring. An extensive product portfolio of
Scalance W components is available for this purpose.
The functionality of related to the SITRANS MDS is described in
great detail on page 8/9 of this catalog.
In the second application the 4 to 20 mA loop is omitted, all data including measured process values and diagnostic information are
transmitted wirelessly to a process control system, for example.
Main advantages are:
• No planning and installation of data cables, resulting in significant cost reductions
• Higher system transparency due to additional and hitherto unfeasible installation of measuring points
• Process optimization due to flexible, temporary and cost-effective measuring points via wireless communication
• Utilization of proven devices by using adapters
• The WirelessHART meshed network also makes it possible to
bridge longer distances
Siemens FI 01 · 2015 US Edition
8/3
8
© Siemens AG 2015
Communication and Software
Communication
WirelessHART
The figure below shows a typical situation for the second application type.
ES
OS
The properties of WirelessHART can be summarized as follows:
• Simplicity in handling and engineering
• Secure communication
• Availability in network
MS
Industrial Ethernet
SIMATIC
system
SITRANS
AW200
SIMATIC ET 200
with HART support
Wireless
HART
IE/WSNPA LINK
PROFIBUS
DP/PA
LINK
SITRANS SITRANS
P280
TF280
PROFIBUS PA
8
WirelessHART is integrated into SIMATIC systems parallel to the
wire-connected devices with HART or PROFIBUS interfaces. In
this case, the 4 to 20 mA line to the control system is not required: all data, i.e. process values, parameters, diagnostic information and functions, is supplied to the automation system on
a wireless basis. This is mainly useful for replacement and expansion measures related to existing systems, and of course
also new systems, but also for temporary and mobile measurements.
The field devices are standard instruments with connected
adapters, or those with integrated wireless communication.
In principle, a differentiation needs to be made between wireless
communication and the power supply for the devices.
When installing a field device, the planning and installation of the
data cable to the control system is usually considered a significant cost driver. This factor is greatly reduced when using wireless communication.
When using 4 to 20 mA/HART field devices with adapters, the
question of powering up always arises - in contrast to batterypowered field devices with integrated wireless modules.
It is important to distinguish between two and four-wire devices
here. Under certain circumstances, the SITRANS AW200
adapter can take over the supply of a connected two-wire device. The power consumption of the field device plays an important role here. If it is too high, an additional power supply becomes necessary. If more than one device is connected to the
SITRANS AW200 adapter, an additional power supply is required.
Four-wire devices always require an additional power supply.
8/4
Siemens FI 01 · 2015 US Edition
■ Function
Simplicity in handling and engineering
• Utilize current tools, same workflow
The description of devices and adapter is carried out using
proven EDDL technology. SIMATIC PDM continues to be used
as a tool.
• Multiple power supply options
Devices can be operated externally with 24 V DC, external or
integrated battery packs as well as solar cells. The option of
using energy from the process or the environment has been
researched at universities and industry for some time. It is expected that results and products will be available in the medium term.
• Reduced installation costs
Depending on use, installation costs for data cables or power
supply cables are not required.
• Coexists with other wireless networks
WirelessHART only uses the ISM band in the 2.4 GHz area,
since it is available across the globe. However, it is also used
by Industrial Wireless LAN (IWLAN), for example. For this reason, a requirement to allow WirelessHART to co-exist with
Wireless LAN networks was an absolute requirement when
this technology was defined. This coexistence has been
achieved by constantly changing the channels and hence frequencies. This is also called "channel hopping".
Moreover, individual channels can be completely disabled
through so-called "blacklisting", for example if they are locally
used by IWLAN.
• Support of star-shaped and meshed network topologies
Networks can be built in both a star-shaped as well as meshed
structure. The advantage of star-shaped networks with a gateway as the centre is that it allows for fast update cycles. However, the range of the network is limited to a maximum of approx. 200 m without obstacles between the gateway and the
devices.
The advantage of meshed networks is their greater range,
since each participant in the network is also a repeater and
forwards the data of remote participants towards the gateway.
The disadvantage: increased transmission times for data between the field device and the gateway.
• Faster commissioning
Once the device is installed, it can usually be commissioned
right away, since the usual waiting time for completing the installation of the cables does not apply in this case.
• Self-organizing and self-healing networks
WirelessHART networks are automatically organized, built and
administered by the Network Manager. Engineering is usually
not required.
The Network Manager is implemented in the IE/WSN-PA LINK,
the WirelessHART gateway from Siemens.
It calculates the optimal connection routes between the network participants and defines an alternative path that can be
used in the case of disruptions in advance. In that sense, the
network can be considered self-healing.
In addition, the Network manager also defines the channels or
frequencies to be used for all communication.
Statistics regarding communication are compiled automatically and are available to users.
• Security - always active
All designated mechanisms with regard to security are available automatically, and do not require any engineering.
• Make changes in the network without the need for configuration. The Network Manager automatically adds and withdraws
participants to/from the network.
© Siemens AG 2015
Communication and Software
Communication
WirelessHART
Secure communication
• Encryption - All information is automatically encrypted with
128 bit AES prior to transmission
• Specific keys for each data packet
• Data integrity - Each data packet is checked for changes or
damage during transport.
• Device authentication
Each device must know the network identification number as
well as the join key. Otherwise the Network Manager does not
include it in the network.
• Channel Hopping
The channel which is used will be changed according to the
Network manager’s specifications after each telegram. This
provides an added level of security against spying activities.
• Failed authentification report
Each unsuccessful attempt by a participant to join the network
will be recorded and made available to the user.
Availability in network
• Communication based on IEEE 802.15.4-2006
Wireless communication takes place on the basis of a proven
industry standard. It allows for very minimal power consumption.
• Utilization of ISM band (2.4 GHz)
This band can be used worldwide without incurring additional
costs.
• Channel hopping overcomes disruptions
Disruptions are usually limited to a small frequency range.
By constantly changing the channel, it is possible to overcome
the effects of such disruptions and hence increase the network’s reliability.
• Channel Black Listing permanently blocks disrupted channels.
When operating another network at the same location, the
channels occupied by that network can be blocked in the
WirelessHART network.
• Self-healing network
This aspect has already been discussed
• Redundant communication paths
The Network manager automatically calculates redundant
communication paths. This significantly increases the level of
availability.
Software Overview
Applications 1 and 2 will require the following software products
Component
Products
Article No.
Maintenance Diagnostic Station SITRANS MDS
1)
Application type 1
SIMATIC PDM and Options
Application type 2
WirelessHART gateway
SIMATIC PDM Basic (4 Tags)
6ES7658-3AB28-0YA5
Extend Basic 10 Tags
6ES7658-3XC00-2YB5
Extend Basic 100 Tags
6ES7658-3XD00-2YB5
Extend Basic 1 000 Tags
6ES7658-3XE00-2YB5
SIMATIC PDM Service (100 Tags)
6ES7658-3JD28-0YA5
HART OPC Server V3.2
Included in SIMATIC PDM1)
IE/WSN-PA LINK with integrated non-removable antenna
6GK1411-6CA40-0AA0
AW2002)
WirelessHART adapter
SITRANS
Process control system
SIMATIC PCS 7
8
7MP3112-1AA00-0AA0
SIMATIC S7/SIMATIC PCS 7 function blocks for communicating with 9AE4110-3AA00
WirelessHART devices using the IE/WSN-PA LINK
WirelessHART gateway
IE/WSN-PA LINK with integrated non-removable aerial2)
6GK1411-6CA40-0AA0
Field devices
SITRANS AW2002)
7MP3112-1AA00-0AA0
SITRANS AW2102)
7MP3111-...
SITRANS
P2802)
SITRANS TF2802)
7MP1120-...
7MP1110-...
1)
You can also contact your Siemens contact person.
2)
Other versions and accessories can be found in the product descriptions of this catalog.
■ More information
More detailed information on the required WirelessHART
software and hardware components can be found in the
FI 01 catalog or at www.siemens.com/wirelesshart.
Siemens FI 01 · 2015 US Edition
8/5
© Siemens AG 2015
Communication and Software
Communication
PROFIBUS
■ Overview
■ Function
Today, distributed automation solutions based on open field
buses are state-of-the-art in large areas of the manufacturing
industry and process engineering. It is only with field buses that
the functional benefits of digital communication can be put to full
use, e.g. better resolution of measured values, diagnosis options
and remote parameterization.
PROFIBUS is today’s most successful open field bus with a large
installed base for a wide range of application. Standardization to
IEC 61158 / EN 50170 provides you with future protection for
your investment.
■ Benefits
• A uniform modular system from the sensor into the control
level enables new plant concepts
• Problem-free exchangeability of field devices, including from
different manufacturers, that comply with the standard profile
• Networking of transmitters, valves, actuators etc.
• Implementation of intrinsically safe applications through use of
the field bus in hazardous areas
• Easy installation of 2-wire lines for joint energy supply and
data transmission
• Reduced cabling costs through savings of material and installation time
• Reduced configuration costs through central, simple
engineering of the field devices (PROFIBUS PA and HART with
SIMATIC PDM, also cross-vendor)
• Fast and error-free installation
• Lower service costs thanks to simpler wiring and plant structure plus extensive diagnosis options
• Greatly reduced commissioning costs through simplified loop
check
• Scaling/digitizing of the measured values in the field device
already, hence no rescaling necessary in SIMATIC PCS 7
■ Application
8
PROFIBUS is suitable for fast communication with distributed
I/Os (PROFIBUS DP) in production automation as well as for
communication tasks in process automation (PROFIBUS PA).
It is the first field bus system that meets the demands of both
areas with identical communication services.
The transmission technique of the PROFIBUS PA is tailored to
the needs of the process industry. Interoperability between field
devices from different manufacturers and remote parameterization of the field devices during operation are guaranteed by the
standardized communication services.
Using SIMATIC PDM (Process Device Manager), a uniform and
cross-vendor tool for configuring, parameterizing, commissioning and diagnosis of intelligent process devices on the
PROFIBUS, it is possible to configure a wide variety of process
devices from different manufacturers using one uniform graphical user interface.
PROFIBUS PA can just as readily used in standard environments
as well as hazardous areas. For use in hazardous areas,
PROFIBUS PA and all connected devices have to be designed
with type of explosion protection Ex [i].
The uniform protocol of PROFIBUS DP and PROFIBUS PA
enables the two networks to be interlinked, thus combining timebased performance with intrinsically safe transmission.
PROFIBUS PA expands PROFIBUS DP with near-process components for the direct connection of actuators and sensors.
For PROFIBUS PA the RS 485 transmission technique was
replaced by a different technique optimized for intrinsically safe
application. Both techniques are internationally standardized in
IEC 61158.
PROFIBUS PA uses the same communication protocol as
PROFIBUS DP; the communication services and telegrams are
identical.
For PROFIBUS PA the data and energy supply for the field
devices can be directed through a 2-wire line.
■ Integration
Siemens field devices for process automation which are listed in
this catalog and can be controlled using PROFIBUS:
PROFIBUS PA
Measuring instruments for pressure
SITRANS P DS III PA
SITRANS P300
Measuring instruments for temperature
SITRANS TH400
Flowmeters
SITRANS F M MAG 6000 19" / IP67
SITRANS F M MAG 6000 I / I Ex
SITRANS F M Transmag 2
SITRANS F C MASS 6000 19" / IP67 / Ex d
SITRANS FUS060
Measuring instruments for level
Pointek CLS200
Pointek CLS300
SITRANS Probe LU
SITRANS LR200
SITRANS LR250
SITRANS LR260
SITRANS LR460
SITRANS LR560
Electropneumatic positioners
SIPART PS2
Acoustic sensor for pump monitoring
SITRANS DA400
PROFIBUS DP
Flowmeters
SITRANS F M MAG 6000 19" / IP67
SITRANS F M MAG 6000 I
SITRANS F C MASS 6000 19" / IP67
SIFLOW FC070 (via ET200M)
Measuring instruments for level
HydroRanger 200
MultiRanger 100/200
SITRANS LU01, LU02, LU10
Acoustic sensor for pump monitoring
SITRANS DA400
8/6
Siemens FI 01 · 2015 US Edition
© Siemens AG 2015
Communication and Software
Communication
FOUNDATION Fieldbus
■ Overview
■ Function
Today, distributed automation solutions based on open field
buses are state-of-the-art in large areas of the process engineering industry. It is only with field buses that the functional benefits
of digital communication can be put to full use, e.g. better resolution of measured values, diagnosis options and remote
parameterization.
FOUNDATION Fieldbus enables the direct connection of actuators and sensors.
Like PROFIBUS PA, the FF bus (FOUNDATION Fieldbus) is an
open field bus with a large installed base for a wide range of application. Standardization to IEC 61158 / EN 50170 provides you
with future protection for your investment.
For FOUNDATION Fieldbus the data and energy supply for the
field devices can be directed through a 2-wire cable.
■ Benefits
• A uniform modular system from the sensor to the connection
to the control level enables new plant concepts
• Networking of transmitters, valves, actuators etc.
• Implementation of intrinsically safe applications through use of
the field bus in hazardous areas
• Easy installation of 2-wire cables for joint energy supply and
data transfer
• Reduced cabling costs through savings of material and installation time.
• Reduced configuration costs through central, simple engineering of the field devices, also cross-vendor
• Fast and error-free installation
• Lower service costs thanks to simpler wiring and plant structure plus extensive diagnosis options
• Greatly reduced commissioning costs through simplified loop
check
• Scaling/digitizing of the measured values in the field device already, hence no rescaling necessary in SIMATIC PCS 7
■ Application
FOUNDATION Fieldbus is based on a transfer optimized for intrinsically safe application. The transfer technology is internationally standardized in IEC 61158.
FOUNDATION Fieldbus enables device-to-device communication ("control in the field").
■ Integration
Siemens field devices for process automation which are listed in
this catalog and can be controlled using Foundation Fieldbus:
Measuring instruments for pressure
SITRANS P300 FF
SITRANS P DS III FF
Measuring instruments for temperature
SITRANS TH400 FF
Electropneumatic positioners
SIPART PS2 FF
Flowmeters
SITRANS F M MAG 6000
SITRANS F M MAG 6000 I / I Ex
SITRANS F C MASS 6000
Level meters
SITRANS LR250
SITRANS LR560
The transfer technology of the FOUNDATION Fieldbus is tailored
to the needs of the process industry. Interoperability between
field devices from different manufacturers and remote parameterization of the field devices during operation are guaranteed
by the standardized communication services.
8
FOUNDATION Fieldbus can just as readily be used in standard
environments as in hazardous areas. For use in hazardous areas, FOUNDATION Fieldbus and all connected devices have to
be designed with type of explosion protection Ex [i].
Siemens FI 01 · 2015 US Edition
8/7
© Siemens AG 2015
Communication and Software
WirelessHART Communication
Communication blocks
■ Overview
■ Function
HMI
Industrial Ethernet
SITRANS TF280
SIMATIC S7-300
SIMATIC S7-400
IE/WSN-PA LINK
WirelessHART adapter
SITRANS P280
Communication block
The WirelessHART communication blocks implement the communication between S7/PCS 7 automation systems and WirelessHART field devices. They communicate via the
IE/WSN-PA LINK using the Modbus TCP/IP protocol. Preconfigured communication blocks simplify the engineering process.
Symbols and face plates are included in the delivery for use with
SIMATIC PCS 7 OS or SIMATIC WinCC.
■ Benefits
A library, which can be installed, offers pre-fabricated blocks
and hence an easy way to integrate WirelessHART devices into
the SIMATIC automation world.
8
Simple configuration thanks to:
• Prefabricated function blocks for IE/WSN-PA LINK and WirelessHART devices
• SIMATIC PCS 7 OS or SIMATIC WinCC symbols and face
plates are included
• Configuring help for IE/WSN-PA LINK in line with function
blocks
• Output of quality codes for respective process values
• Analysis of IE/WSN-PA LINK diagnostic information
■ Application
WirelessHART communication blocks are used where SIMATIC
automation systems communicate with WirelessHART devices
via the IE/WSN-PA LINK gateway.
8/8
Siemens FI 01 · 2015 US Edition
The function blocks cyclically communicate with the
IE/WSN-PA LINK via Modbus TCP/IP. Process values of
WirelessHART devices as well as their status are read and made
available at the function block outputs. Furthermore, selected
status information of the IE/WSN-PA LINK is also made available
at another building block. This information includes connection
status, condition of the wireless network and other diagnostics.
Precondition of the usage of these communication blocks is a
TCP/IP connection, engineered in NetPro in the Engineering Station of Simatic PCS 7. Currently this requires a CP343 or a
CP443-1.
■ Configuration
The standard S7 or PCS 7 engineering tools CFC, KOP, FUP can
be used for the communication block engineering. Connection
planning is done in NetPro. A configuration example for configuring the IE/WSN-PA LINK makes it easy to assign the
WirelessHART devices to the communication blocks which need
to be engineered.
■ More information
You can obtain function blocks and technical support for integrating the IE/WSN-PA LINK in PCS 7 at the following address:
Siemens AG
DF CS DS PAS R&D-AP
Roland Heid
Siemensallee 84
76187 Karlsruhe
Germany
Tel: +49 721 595-6380
E-Mail: [email protected]
■ Selection and Ordering data
S7/PCS 7 function blocks for
communicating with
WirelessHART devices using
the IE/WSN-PA LINK
S7-300 or S7-400,
including face plate
Article No.
9AE4110-3AA00
© Siemens AG 2015
Communication and Software
WirelessHART Communication
SITRANS MDS - Maintenance Diagnostic Station
■ Overview
■ Design
SITRANS MDS uses SIMATIC PDM project data to read and
display diagnostic data from accessible devices.
SITRANS
MDS
OS
Industrial Ethernet
Controller without
HART support
SITRANS
AW200
4 –20 mA
IWLAN
IEEE802.11
Maintenance Diagnostic Station
SITRANS MDS for flexible and automated diagnostic processing:
• Central display of diagnostic information from HART devices,
which was only readable on site until now.
• Adjustable updating period for each device
• Clear visualization of diagnostic status of all devices
• Simply transfer of SIMATIC PDM configuring data
• Windows-based application
4 –20 mA
Wireless
HART
Industrial
Ethernet
■ Benefits
SITRANS MDS in cooperation with SIMATIC PDM increases significantly the transparency of a plant.
The main advantages of SIMATIC MDS are as follows:
• Increase transparency of the plant by reading diagnostic information from accessible devices and providing a well-organized representation of this information
• Representation of diagnostic status of a device as in
SIMATIC PCS 7 or NAMUR NE 107 (switchable)
• Ease of use through use of SIMATIC PDM project data
• The update cycle for the diagnostic status can be uniformly
set as the default value for all devices ...
• ... as well as for each device individually
■ Application
4 –20 mA
IE/WSNPA LINK
PROFIBUS
Remote I/O station
w/o HART support
■ Integration
SITRANS MDS is installed on a PC together with SIMATIC PDM.
Only the stand-alone version is used in this case.
8
■ Configuration
Configuration required for SITRANS MDS is adopted from
SIMATIC PDM. Only the project name must be entered.
Very few other entries are required, such as the definition of
update periods.
SITRANS MDS increases the transparency of a plant by centrally
collecting diagnostic information, directly from the accessible
field devices. In principle, all devices that are integrated in
SIMATIC PDM can be included in the collecting process.
SITRANS MDS can be used where the installed automation system does not support an integrated acyclic communication of
parameters and diagnostic information with the devices. In the
case of HART devices, this applies to 85% of all installed
devices.
The modern SIMATIC PCS 7 process control system allows for
this type of continuous communication from the engineering system up to the devices. It also features a decidedly higher performance asset management system. The use of SIMATIC MDS
therefore does not make sense in a SIMATIC PCS 7 environment
and is hence not approved for that purpose.
Siemens FI 01 · 2015 US Edition
8/9
© Siemens AG 2015
Communication and Software
WirelessHART Communication
SITRANS MDS - Maintenance Diagnostic Station
■ Technical specifications
SITRANS MDS Maintenance Diagnostic Station
Operating system
Microsoft Windows XP
professional SP2/SP3
Additionally required software
SIMATIC PDM as of V 6.05 and
options
• SIMATIC PDM Basic (4 Tags)
6ES7 658-3AX16-0YA5
• SIMATIC PDM service (128 Tags)
6ES7 658-3JX16-0YA5
• SIMATIC PDM Option HART Mux
6ES7 658-3EX16-2YB5
Additional options to increase
number of measuring points
PC hardware
600 MHz
256 MB *)
XGA 1024 x 768
16 Bit color depth
*) main memory of at least
512 MB is recommended
Up-to-date information can be
found in the description for
SIMATIC PDM
■ Selection and Ordering data
SITRANS MDS is a software package which is delivered together
with the IE/WSN-PA LINK for Version 1.0.
8
8/10
Siemens FI 01 · 2015 US Edition
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
■ Overview
SIMATIC PCS 7
engineering station
with SIMATIC PDM
PDM Stand-alone
SIMATIC PCS 7
maintenance station client
with SIMATIC PDM
Device on
the workbench
Industrial Ethernet
S7-400
S7-400
PROFINET
ET 200M
(also with
HART modules)
PROFIBUS PA
IE/PB Link PN IO
+ DP/PA coupler
SIMOCODE
PROFIBUS DP
HART protocol
RS 232/RS 485
Field devices
SIMOCODE
ET 200iSP
HART
multiplexer
Possible connection point of a
PG/PC with SIMATIC PDM
(stand-alone operation)
G_PCS7_XX_00386
FF H1
ET 200M
HART
PROFIBUS PA
FF link
HART
PA link
Configuration options with SIMATIC PDM
SIMATIC PDM (Process Device Manager) is a universal, vendorindependent tool for the configuration, parameter assignment,
commissioning, diagnostics and servicing of intelligent field
devices (sensors and actuators) and field components (remote
I/Os, multiplexers, control-room devices, compact controllers),
which in the following sections will be referred to simply as
devices.
Using one software, SIMATIC PDM enables the processing of
more than 2 500 devices from Siemens and over 200 vendors
worldwide on one homogeneous user interface.
The user interface satisfies the requirements of the
VDI/VDE GMA 2187 and IEC 65/349/CD directives. Parameters
and functions for all supported devices are displayed in a
consistent and uniform fashion independent of their communications interface. Even complex devices with several hundred
parameters can be represented clearly and processed quickly.
Using SIMATIC PDM it is very easy to navigate in highly complex
stations such as remote I/Os and even connected field devices.
From the viewpoint of device integration, SIMATIC PDM is the
most powerful open device manager available in the world.
Devices which previously were not supported can be integrated
in SIMATIC PDM by importing their device descriptions (EDD).
This provides security for your investment and saves you investment costs, training expenses and follow-up costs.
SIMATIC PDM supports the operative system management in
particular through:
• Uniform presentation and operation of devices
• Uniform representation of diagnostics information
• Indicators for preventive maintenance and servicing
• Detection of changes in the project and device
• Increasing the operational reliability
• Reducing the investment, operating and maintenance costs
When used in SIMATIC PCS 7, SIMATIC PDM is integrated in the
maintenance station of the process control system and transmits
parameter data and diagnostics information. You can change
directly to the SIMATIC PDM views from the diagnostics faceplates in the Maintenance Station.
As an option, SIMATIC PDM can also be started on any SIMATIC
PCS 7 maintenance station client (MS Client) in order to parameterize and diagnose the devices integrated per Electronic
Device Description (EDD). In this context, SIMATIC PDM user
administration based on SIMATIC Logon allows various roles
with defined function privileges to be assigned to users. These
function privileges refer to SIMATIC PDM system functions, e.g.
writing to the device.
For all devices described per Electronic Device Description
(EDD), SIMATIC PDM delivers a range of information for display
and further processing on the maintenance station, e.g.:
• Device type information (electronic rating plate)
• Detailed diagnostics information (manufacturer information,
information on error diagnostics and troubleshooting, further
documentation)
• Results of internal condition monitoring functions
• Status information (e.g. local configuration changes)
• Information on changes (audit trail report)
• Parameter information
Siemens FI 01 · 2015 US Edition
8/11
8
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
■ Application
Components
Product packages
SIMATIC PDM stand-alone
Minimum
configuration
SIMATIC PDM system-integrated
Basic
configuration
Application-specific configurations
SIMATIC PDM SIMATIC PDM SIMATIC PDM SIMATIC PDM
Single Point
Basic
Service
S7
SIMATIC PDM
PCS 7
V8.2
V8.2
V8.2
V8.2
V8.2
Server V8.2
FF V8.2
1
4
4 + 100
4 + 100
4 + 100
4 + 100
4 + 100
cannot be
expanded
o
o
o
o
o
o
SIMATIC PDM Basic
n
n
n
n
n
n
SIMATIC PDM Extended
o
o
n
n
n
n
SIMATIC PDM integration in STEP 7/PCS 7
o
o
n
n
n
n
SIMATIC PDM routing
o
o
o
n
n
n
SIMATIC PDM Server
o
o
o
o
n
o
SIMATIC PDM Communication
FOUNDATION Fieldbus
o
o
o
o
o
n
SIMATIC PDM HART server
o
o
o
o
o
o
SIMATIC PDM command interface2)
o
o
–
–
–
–
SIMATIC PDM TAGs1) in product package
SIMATIC PDM expansion options
Count Relevant
Licenses
(accumulative)
- 10 TAGs
- 100 TAGs
- 1 000 TAGs
SIMATIC PDM product structure
n
Product component is part of the product package
o Optional product component for the product package; order additive
– Product component is not relevant for the product package or not available
1)
For TAG definition, see "Design" section under "SIMATIC PDM TAGs"
2)
Only for special applications, not envisaged for wide use: Programming knowledge is necessary.
Customer-oriented product structure
SIMATIC PDM is highly versatile in the context of Totally Integrated Automation (TIA): Stand-alone or system-integrated in a
SIMATIC PCS 7 / SIMATIC S7 configuration environment.
8
The customer-oriented products structure of SIMATIC PDM
helps you to adapt the scope of functions and performance to
your individual requirements. You have the following options:
SIMATIC PDM stand-alone
• Product packages for operation on a mobile computer with
local bus connection or with direct connection to the device,
optionally as:
- Minimal configuration SIMATIC PDM Single Point for
processing of a single field device via point-to-point
coupling
- Application-specific configuration SIMATIC PDM Service for
extended service tasks
• Product package SIMATIC PDM Basic as the basis for an
individual SIMATIC PDM configuration with optional product
components (see table)
8/12
Siemens FI 01 · 2015 US Edition
SIMATIC PDM system-integrated
• Product packages for integration of SIMATIC PDM in the
engineering system (engineering toolset) and Maintenance
Station of the SIMATIC PCS 7 process control system:
- SIMATIC PDM PCS 7
- SIMATIC PDM PCS 7 Server (enables SIMATIC PDM to
be started on any MS client)
- SIMATIC PDM PCS 7-FF (also supports the
FOUNDATION Fieldbus H1)
• Product package SIMATIC PDM S7 for integration in a
SIMATIC S7 configuration environment
In some circumstances, the various product packages can be
expanded with optional product components (for details, see the
Design section).
Selection criteria
In addition to considering the environment of use and the functional and performance features when selecting the product
(see table in "Design" section), also observe the system requirements (see "Technical specifications" section).
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
■ Design
Product range
SIMATIC PDM SIMATIC PDM SIMATIC PDM SIMATIC PDM
Single Point
Basic
Service
S7
SIMATIC PDM PCS 7
V8.2
V8.2
V8.2
V8.2
V8.2
Server V8.2
FF V8.2
TAGs contained
1
4
4 + 100
4 + 100
4 + 100
4 + 100
4 + 100
Project: Create offline
n
n
n
n
n
n
n
Project: Usable TAG extensions
–
n
n
n
n
n
n
Project: Process device network view
n
n
n
n
n
n
n
Project: Process device plant view
n
n
n
n
n
n
n
Project: Export/import devices
–
–
n
–
–
–
–
Project: Export/import parameters
–
o
n
n
n
n
n
Project: HW Config
–
o
o
n
n
n
n
Project: Utilization of SIMATIC PDM options
–
n
n
n
n
n
n
Project: Integration in STEP 7/PCS 7
–
o
o
n
n
n
n
Communication: HART modem
n
n
n
n
n
n
n
Communication: HART interface
n
n
n
n
n
n
n
Communication: PROFIBUS DP/PA
n
n
n
n
n
n
n
Communication: HART over PROFIBUS DP
n
n
n
n
n
n
n
Communication: FF H1
–
o1)
o1)
o
o
o
n
Communication: Modbus
n
n
n
n
n
n
n
Communication: Ethernet
n
n
n
n
n
n
n
Communication: PROFINET
n
n
n
n
n
n
n
Communication: HART over PROFINET
n
n
n
n
n
n
n
Devices: Export/import parameters
–
o
n
n
n
n
n
Devices: Comparison of parameter values
–
o
n
n
n
n
n
Devices: Saving parameters
n
n
n
n
n
n
n
Devices: Change log (Audit Trail)
–
o
n
n
n
n
n
Devices: Calibration report
–
o
n
n
n
n
n
Devices: Print function
n
o
n
n
n
n
n
Devices: Document manager
–
o
n
n
n
n
n
Lifelist: Basic functionality
n
n
n
n
n
n
n
Lifelist: Expanded functionality (scan range,
diagnostics, export, addressing)
–
o
n
n
n
n
n
Communication: S7 routing
–
o
o
o
n
n
n
Communication: HART multiplexer
–
o
o
o
o
o
o
Communication: Wireless HART
–
o
o
o
o
o
o
Function: HART SHC mode (increased communication speed)
n
n
n
n
n
n
n
Function: Device parameterization on PCS 7
maintenance station clients
–
o
o
o
o
n
o
SIMATIC PDM overview of functions and features
n
Product component is part of the product package
o Optional product component for the product package; order additive
– Product component is not relevant for the product package or not available
1)
Not in stand-alone mode
Siemens FI 01 · 2015 US Edition
8/13
8
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
SIMATIC PDM stand-alone product range
SIMATIC PDM Single Point V8.2
SIMATIC PDM S7 V8.2
This minimum configuration with handheld functionality is
designed for processing exactly one field device via point-topoint coupling. Additional functions or SIMATIC PDM TAGs are
not possible. Upgrading to a different product variant, e.g.
SIMATIC PDM Basic, or a different product version is also not
possible. The device functions are supported as defined in the
device description.
The product package designed for use in a SIMATIC S7 configuration environment requires the installation of STEP 7
V5.5+SP4. It comprises:
• SIMATIC PDM Basic (incl. 4 SIMATIC PDM TAGs)
• SIMATIC PDM Extended
• SIMATIC PDM integration in STEP 7/PCS 7
• 100 SIMATIC PDM TAGs
The following types of communication are possible:
• PROFIBUS DP/PA
• HART communication (modem, RS 232 and via
PROFIBUS/PROFINET)
• Modbus
• Ethernet
• PROFINET
SIMATIC PDM Basic V8.2
Provided the system requirements are met, SIMATIC PDM Basic
can be used for stand-alone operation on any computer
(IPC/notebook) with local connection to bus segments or direct
connection to the device. The product package features all the
basic functions required for operation and parameter assignment of the devices and is enabled for the following communication modes:
• PROFIBUS DP/PA
• HART communication (modem, RS 232 and via
PROFIBUS/PROFINET)
• Modbus
• Ethernet
• PROFINET
As a basic block for individual configuration, SIMATIC PDM
Basic can be upgraded with all functional SIMATIC PDM options
as well as with cumulative sets of 10, 100 or 1 000 SIMATIC PDM
TAGs. Without TAG expansion, SIMATIC PDM Basic is suitable
for projects with up to 4 TAGs.
SIMATIC PDM Service V8.2
8
SIMATIC PDM system-integrated product range
The product package for mobile servicing applications can be
executed on any computer (IPC/notebook) with a local connection to a bus segment or direct connection to field devices.
It comprises:
• SIMATIC PDM Basic (incl. 4 SIMATIC PDM TAGs)
• 100 SIMATIC PDM TAGs
Similar to SIMATIC PDM Basic, SIMATIC PDM Service can be
upgraded with all functional SIMATIC PDM options as well as
with cumulative sets of 10, 100 or 1 000 SIMATIC PDM TAGs.
SIMATIC PDM S7 can be expanded with the functional options
SIMATIC PDM Routing, SIMATIC PDM Communication FOUNDATION Fieldbus, SIMATIC PDM Server, and SIMATIC PDM
HART Server as well as with cumulative sets of 10, 100 or 1 000
SIMATIC PDM TAGs.
SIMATIC PDM PCS 7 V8.2
The product package designed for use in a SIMATIC PCS 7
configuration environment requires the installation of SIMATIC
PCS 7 V8.1. SIMATIC PDM can then be integrated in the engineering toolset of the SIMATIC PCS 7 Engineering System V8.1.
It comprises:
• SIMATIC PDM Basic (incl. 4 SIMATIC PDM TAGs)
• SIMATIC PDM Extended
• SIMATIC PDM integration in STEP 7/PCS 7
• SIMATIC PDM Routing
• 100 SIMATIC PDM TAGs
SIMATIC PDM PCS 7 can be expanded with the functional
options SIMATIC PDM Communication FOUNDATION Fieldbus,
SIMATIC PDM Server, and SIMATIC PDM HART Server (see
"Optional product components") as well as with cumulative sets
of SIMATIC PDM TAGs (10, 100 or 1 000).
SIMATIC PDM PCS 7 Server V8.2
The product package designed for use in a SIMATIC PCS 7
configuration environment requires the installation of SIMATIC
PCS 7 V8.1. It expands the functionality of SIMATIC PDM PCS 7
by the SIMATIC PDM Server option. It is then possible to parameterize field devices integrated per Electronic Device Description (EDD) on any client of the SIMATIC PCS 7 Maintenance
Station V8.1.
SIMATIC PDM PCS 7 Server can be expanded with the functional options SIMATIC PDM Communication FOUNDATION
Fieldbus and SIMATIC PDM HART Server (see "Optional product
components") as well as with cumulative sets of SIMATIC PDM
TAGs (10, 100 or 1 000).
SIMATIC PDM PCS 7-FF V8.2
The product package designed for use in a SIMATIC PCS 7
configuration environment requires the installation of SIMATIC
PCS 7 V8.1. It expands the functionality of SIMATIC PDM PCS 7
by the SIMATIC PDM Communication FOUNDATION Fieldbus
option. SIMATIC PDM can then also parameterize field devices
on the FOUNDATION Fieldbus H1.
SIMATIC PDM PCS 7-FF can be expanded with the functional
options SIMATIC PDM Server and SIMATIC PDM HART Server
(see "Optional product components") as well as with cumulative
sets of SIMATIC PDM TAGs (10, 100 or 1 000).
8/14
Siemens FI 01 · 2015 US Edition
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
Optional product components
SIMATIC PDM TAGs (version-independent)
SIMATIC PDM Extended V8.2 option
Depending on the project size, the SIMATIC PDM TAGs supplied
with a product package (except SIMATIC PDM Single Point) can
be cumulatively expanded with sets of 10, 100 or 1 000 SIMATIC
PDM TAGs.
The SIMATIC PDM Extended option enables you to unlock other
system functions for SIMATIC PDM Basic and SIMATIC PDM, for
example:
• Change log
• Calibration report
• Extended information in the Lifelist
• Export and import functions
• Print functions
• Document manager
• Comparison function
A SIMATIC PDM TAG corresponds to a SIMATIC PDM object,
which represents individual field devices or components within
a project, e.g. measuring instruments, positioners, switching
devices or remote I/Os. SIMATIC PDM TAGs are also relevant for
diagnostics with the lifelist of SIMATIC PDM. In this case, TAGs
are considered to be all recognized devices with diagnostics
capability, whose detailed diagnostics is effected through the
device description (EDD).
SIMATIC PDM Software Media Package V8.2
This functionality is already integrated in the product packages
of category "SIMATIC PDM system-integrated" (SIMATIC
PDM S7, SIMATIC PDM PCS 7, SIMATIC PDM PCS 7 Server, and
SIMATIC PDM PCS 7-FF).
The current SIMATIC PDM installation software is offered without
a license in the form of the SIMATIC PDM Software Media
Package. Purchasing of corresponding software licenses is
necessary to unlock the product-specific functionalities.
SIMATIC PDM integration option in STEP 7/PCS 7 V8.2
With SIMATIC PDM product packages, type of delivery
"Package" (not with optional product components), a SIMATIC
PDM Software Media Package is supplied together with each
ordering item. Further SIMATIC PDM Software Media Packages
must be ordered separately as required.
This option is used for the integration of SIMATIC PDM in a
SIMATIC S7 or SIMATIC PCS 7 configuration environment.
SIMATIC PDM can then be started directly from the hardware
configurator (HW Config) in STEP 7/SIMATIC PCS 7.
This functionality is already integrated in the product packages
of category "SIMATIC PDM system-integrated" (SIMATIC
PDM S7, SIMATIC PDM PCS 7, SIMATIC PDM PCS 7 Server, and
SIMATIC PDM PCS 7-FF).
SIMATIC PDM Routing V8.2 option
If SIMATIC PDM is used on an engineering station, the SIMATIC
PDM Routing option enables handling of every device in the field
that can be configured per EDD throughout the plant and across
different bus systems and remote I/Os. SIMATIC PDM Routing is
offered as an optional product component for SIMATIC PDM
Basic, SIMATIC PDM Service, and SIMATIC PDM S7.
The software of the SIMATIC PDM Media Package without a
license can be used for demonstration purposes in demo mode.
The SIMATIC PDM functionality is limited as follows in demo
mode:
• Stand-alone operation
• Storage functions disabled
• Export and import functions disabled
• Expanded functionality disabled
• Communication functions restricted
Routing is already integrated in SIMATIC PDM PCS 7, SIMATIC
PDM PCS 7 Server, and SIMATIC PDM PCS 7-FF.
SIMATIC PDM Server V8.2 option
This option is intended for use of SIMATIC PDM in the SIMATIC
PCS 7 Maintenance Station V8.1. Selected field devices can
then be handled using the SIMATIC PDM configuration GUI on
each client of the SIMATIC PCS 7 Maintenance Station V8.1.
8
SIMATIC PDM Communication FOUNDATION Fieldbus V8.2
option
In a SIMATIC S7/PCS 7 configuration environment, using this
option SIMATIC PDM can communicate with field devices on the
FOUNDATION Fieldbus H1 via the FF link.
This functionality is already integrated in the SIMATIC PDM
PCS 7-FF product package.
SIMATIC PDM HART Server V8.2 option
This option permits the use of HART multiplexers from various
vendors in SIMATIC PDM. Furthermore, wireless HART field
devices can also be parameterized with SIMATIC PDM.
SIMATIC PDM Command Interface V8.2 option
SIMATIC PDM configurations for stand-alone operation, based
on the SIMATIC PDM Basic or SIMATIC PDM Service product
package, can be remote-controlled by this option with regard to
configuration and field device operation.
Note: The SIMATIC PDM Command Interface option can only be
used specific to a project. It is not envisaged for wide use.
Programming knowledge is necessary.
Siemens FI 01 · 2015 US Edition
8/15
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
■ Function
■ Integration
Device integration
SIMATIC PDM supports all devices described by EDD (Electronic Device Description). EDD is standardized to EN 50391
and IEC 61804. Internationally it is the most widely used standardized technology for device integration. At the same time, it
is the guideline of the established organizations for
• PROFIBUS and PROFINET (PI – PROFIBUS & PROFINET
International)
• HART (HCF: HART Communication Foundation)
• FF (Fieldbus Foundation)
The devices are integrated directly in SIMATIC PDM through a
company-specific EDD or the current HCF or Fieldbus Foundation libraries. To achieve improved transparency, they can be
managed in project-specific device libraries.
Field devices are described in the EDD in terms of functionality
and construction using the Electronic Device Description
Language (EDDL). Using this description, SIMATIC PDM automatically creates its user interfaces with the specific device
data. Existing devices can be updated, and further devices integrated into SIMATIC PDM, by simply importing the manufacturer's device-specific EDD.
Fieldbus Foundation provides pre-defined device descriptions
(standard DD) for the basic functions of specific field device
types. The basic functions are implemented using various standard function and transmission blocks.
Technical support
SIMATIC PDM, parameter view and trend window
8
SIMATIC PDM core functions
• Creation of project-specific device libraries
• Adjustment and modification of device parameters
• Comparing (e.g. project and device data)
• Plausibility testing of data input
• Device identification and testing
• Device status indication (operating modes, interrupts, states)
• Simulation
• Diagnostics (standard, detailed)
• Export/import (parameter data, logs, documents)
• Management (e.g. networks and PCs)
• Commissioning functions, e.g. measuring circuit tests of
device data
• Lifecycle management functions, e.g. for device replacement
• Global and device-specific modification logbook for user
operations (audit trail)
• Device-specific calibration reports
• Graphic presentations of echo envelope curves, trend
displays, valve diagnosis results etc.
• Presentation of incorporated manuals
• Document manager for integration of up to 10 multimedia files
8/16
Siemens FI 01 · 2015 US Edition
If you wish to use devices which cannot be found in the SIMATIC
PDM device description library, we would be pleased to help you
integrate them.
Support Request
You can request support by service specialists at Technical
Support by using a "Support Request" on the Internet:
www.siemens.com/automation/support-request
Contacts in the Region
The Technical Support responsible for your Region can be found
on the Internet at:
www.automation.siemens.com/partner
■ Technical specifications
SIMATIC PDM V8.2
Hardware
• PG/PC/notebook with processor corresponding to operating system requirements
Operating systems (alternative)
• Windows 7 Professional/Ultimate/
Enterprise SP1 (32-bit/64-bit)
• Windows Server 2008 R2 SP1 Standard
Edition (64-bit)
Integration in STEP 7/PCS 7
• SIMATIC PCS 7 V8.1 (incl. update 1)
• STEP 7 V5.5+SP4
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
■ Ordering data
Article No.
SIMATIC PDM stand-alone
product packages
Configuration for mobile service
SIMATIC PDM Service V8.2
Product package for stand-alone
user in service, with
• SIMATIC PDM Basic incl. 4 TAGs
• 100 TAGs
Minimum configuration
SIMATIC PDM Single Point V8.2
including 1 TAG; product package
for operation and configuration of
one field device; communication via
PROFIBUS DP/PA, HART (modem,
RS 232, PROFIBUS/PROFINET),
Modbus, Ethernet or PROFINET
Additional functions or SIMATIC
PDM TAGs are not possible
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with
1 × SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
6ES7658-3HA28-0YA5
6ES7658-3HA28-0YH5
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with
1 × SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
6ES7658-3JD28-0YA5
6ES7658-3JD28-0YH5
SIMATIC PDM system-integrated
product packages
Configuration for integration
in SIMATIC S7 configuration
environment
SIMATIC PDM S7 V8.2
Basic configuration for
individual product packages
Product package for use in a
SIMATIC S7 configuration environment, with
- SIMATIC PDM Basic incl. 4 TAGs
- SIMATIC PDM Extended
- SIMATIC PDM integration in
STEP 7/PCS 7
- 100 TAGs
SIMATIC PDM Basic V8.2
including 4 TAGs; product package for operation and configuration
of field devices and components;
communication via
PROFIBUS DP/PA, HART (modem,
RS 232, PROFIBUS/PROFINET),
Modbus, Ethernet or PROFINET
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with
1 × SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
Article No.
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
6ES7658-3AB28-0YA5
6ES7658-3AB28-0YH5
Note:
STEP 7 V5.5+SP4 is required to use
the full functionality of SIMATIC
PDM S7 V8.2!
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with 1 ×
SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
8
6ES7658-3KD28-0YA5
6ES7658-3KD28-0YH5
Siemens FI 01 · 2015 US Edition
8/17
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
Configuration for integration in
SIMATIC PCS 7 configuration
environment
SIMATIC PDM PCS 7 Server V8.2
Product package for integration into
the engineering toolset of the
SIMATIC PCS 7 engineering system
SIMATIC PDM PCS 7 V8.2
Product package for integration into
the engineering toolset of the
SIMATIC PCS 7 engineering system
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit
Floating license for 1 user, with
- SIMATIC PDM Basic incl. 4 TAGs
- SIMATIC PDM Extended
- SIMATIC PDM integration in
STEP 7/PCS 7
- SIMATIC PDM Routing
- SIMATIC PDM Server
- 100 TAGs
Floating license for 1 user, with
- SIMATIC PDM Basic incl. 4 TAGs
- SIMATIC PDM Extended
- SIMATIC PDM integration in
STEP 7/PCS 7
- SIMATIC PDM Routing
- 100 TAGs
Note:
SIMATIC PCS 7 V8.1 is required to
use the full functionality of SIMATIC
PDM PCS 7 V8.2!
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with
1 × SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
6ES7658-3LD28-0YA5
6ES7658-3LD28-0YH5
SIMATIC PDM PCS 7-FF V8.2
Product package for integration into
the engineering toolset of the
SIMATIC PCS 7 engineering system
8
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit
Floating license for 1 user, with
- SIMATIC PDM Basic incl. 4 TAGs
- SIMATIC PDM Extended
- SIMATIC PDM integration in
STEP 7/PCS 7
- SIMATIC PDM Routing
- SIMATIC PDM Communication
FOUNDATION Fieldbus
- 100 TAGs
Note:
SIMATIC PCS 7 V8.1 is required to
use the full functionality of SIMATIC
PDM PCS 7-FF V8.2!
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with 1 ×
SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
8/18
6ES7658-3MD28-0YA5
6ES7658-3MD28-0YH5
Siemens FI 01 · 2015 US Edition
Note:
SIMATIC PCS 7 V8.1 is required to
use the full functionality of SIMATIC
PDM PCS 7 Server V8.2!
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
License key USB stick and certificate of license, bundled with
1 × SIMATIC PDM Software Media
Package per ordering position
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Notes:
E-mail address required; installation software also available separately as SIMATIC PDM Software
Media Package.
6ES7658-3TD28-0YA5
6ES7658-3TD28-0YH5
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
Optional product components for
SIMATIC PDM V8.2
SIMATIC PDM Extended V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Note:
E-mail address required!
6ES7658-3NX28-2YB5
6ES7658-3NX28-2YH5
SIMATIC PDM Integration in
STEP 7/SIMATIC PCS 7 V8.2
only required for integration of
SIMATIC PDM into HW Config
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Note:
E-mail address required!
SIMATIC PDM Routing V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download, online
certificate of license
Note:
E-mail address required!
6ES7658-3BX28-2YB5
6ES7658-3BX28-2YH5
6ES7658-3CX28-2YB5
6ES7658-3CX28-2YH5
SIMATIC PDM Server V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick, certificate
of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Note:
E-mail address required!
SIMATIC PDM Communication
FOUNDATION Fieldbus V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Note:
E-mail address required!
SIMATIC PDM HART Server V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
• Delivery form online
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key download and online
certificate of license
Note:
E-mail address required!
6ES7658-3TX28-2YB5
6ES7658-3TX28-2YH5
6ES7658-3QX28-2YB5
6ES7658-3QX28-2YH5
6ES7658-3EX28-2YB5
8
6ES7658-3EX28-2YH5
Siemens FI 01 · 2015 US Edition
8/19
© Siemens AG 2015
Communication and Software
Software
SIMATIC PDM Process Device Manager
SIMATIC PDM
Command Interface V8.2
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit, floating license for 1 user
• Delivery form package
(without SIMATIC PCS 7/SIMATIC
PDM Software Media Package)
License key USB stick and certificate of license
SIMATIC PDM TAGs
TAG licenses for expanding the
available TAG volume, cumulative,
software class A, floating license for
1 user
• Delivery form package
License key on USB stick and
certificate of license
- 10 TAGs
- 100 TAGs
- 1 000 TAGs
• Delivery form online
License key download and online
certificate of license
Note:
E-mail address required!
- 10 TAGs
- 100 TAGs
- 1 000 TAGs
SIMATIC PDM
Software Media Package
6ES7658-3SX28-2YB5
6ES7658-3XC00-2YB5
6ES7658-3XD00-2YB5
6ES7658-3XE00-2YB5
SIMATIC PDM
Software Media Package V8.2
Installation software without license,
6 languages (English, German,
French, Italian, Spanish, Chinese),
software class A, runs with
Windows 7 Ultimate 32/64-bit or
Windows Server 2008 R2 Standard
64-bit
Note: Can only be used in conjunction with a valid license or in demo
mode!
• Delivery form package
(without SIMATIC PCS 7 Software
Media Package)
SIMATIC PDM and device library
software on DVD
• Delivery form online
(without SIMATIC PCS 7 Software
Media Package)
SIMATIC PDM and device library
software download
Note:
E-mail address required!
6ES7658-3GX28-0YT8
6ES7658-3GX28-0YG8
6ES7658-3XC00-2YH5
6ES7658-3XD00-2YH5
6ES7658-3XE00-2YH5
■ More information
Update/Upgrade
Product packages and optional product components from the
product range of SIMATIC PDM V6.0, V6.1, V8.0 or V8.1 (incl.
service pack) can be directly upgraded to V8.2 using upgrade
packages. Excepted from this are SIMATIC PDM Single Point
and SIMATIC PDM Communication via standard HART multiplexer.
8
Product packages and optional product components from the
product range of SIMATIC PDM V7.0 can first be upgraded to
V8.0 and then to V8.2.
When upgrading to SIMATIC PDM V8.2, be aware of the
compatible versions of SIMATIC PCS 7 and STEP 7.
8/20
Siemens FI 01 · 2015 US Edition
A Software Update Service in the form of a subscription is also
offered for SIMATIC PDM.
For further information, see catalog ST PCS 7.
© Siemens AG 2015
Communication and Software
Software
SITRANS DTM
■ Overview
The following field instruments are currently available in
SITRANS DTM:
• SITRANS TH300 HART
• SITRANS TH400 PA
• SITRANS P300 HART
• SITRANS P500
• SITRANS P DSIII HART
• SITRANS F M MAG 6000 DP/PA
• SITRANS F C MASS 6000 PA/PA
• SITRANS FC430
• SITRANS PROBE LU 6 m, 12 m, HART
• SITRANS LR200 HART, PA
• SITRANS LR250 HART, PA
• SITRANS LR260 HART, PA
• SITRANS LR560 HART, PA
• SITRANS LUT400 HART
• SIPART PS2 HART, PA, FF
■ Technical specifications
SITRANS DTM provides an easy way for Field Device Tool (FDT)/
Device Type Manager (DTM) users to parameterize Siemens
Instruments using international standards.
■ Benefits
•
•
•
•
•
Same look and feel for all Siemens field instruments
Support for Quick start wizards and other dialog boxes
Quick overview using table and tree views
Online and offline configuration
Conformity to IEC profiles for HART and PROFFIBUS
■ Application
SITRANS DTM
Version
Current Version
3.1
• Compatible with
PACTware versions
3.6, 4.0, 4.1
• Compatible with Windows
XP, 7
• Certified by FDT group
Yes
Free DTM software can be downloaded from:
http://www.siemens.com/sitransdtm
Click on Support in the collateral list on the right side of the web
page, and choose Software downloads.
Electronic Device Description (EDD) is a proven way to describe
the behavior and functionality of field instruments and other
automation components.
For many years, EDD-based tools such as SIMATIC PDM from
Siemens or handheld communicator have been used successfully in the process industry. Some years ago, an additional technology called FDT / DTM with the same approach was introduced to the market. To support the FDT DTM Technology for
Siemens devices, the software SITRANS DTM has been developed which combines both EDD and FDT technologies.
SITRANS DTM uses EDDs as the device description and
provides the DTM interface to allow the integration of our field
instruments into FDT-frame applications.
8
Siemens FI 01 · 2015 US Edition
8/21
© Siemens AG 2015
Communication and Software
Software
SITRANS Library
■ Overview
■ Design
The product structure, however, is geared toward the operational
environment in the SIMATIC PCS 7 process control system. Consequently, SITRANS Library is offered in the form of an engineering component:
• SITRANS Library
Engineering software with engineering license for one customer plant
• SITRANS Library
Runtime license for one automation system (SIMATIC PCS 7
automation systems of all designs and S7-300 controllers)
The SITRANS Library product component enables you to perform configuration work on a SIMATIC PCS 7 engineering station.
The SITRANS Library product component allows you to run
blocks from a library on an automation system.
When using function blocks from SITRANS Library in
SIMATIC PCS 7 automation systems, note that SIMATIC PCS 7
AS Runtime POs are also booked.
The SITRANS Library for SIMATIC PCS 7 V8.0 extends standard
functionality of the SIMATIC PCS 7 process control system concentrated in the SIMATIC PCS 7 Advanced Process Library
(APL) with technological blocks and faceplates for device-specific functions of the SITRANS field devices.
■ Benefits
This allows you to easily operate all device functions, such as the
dosing of the SITRANS FM MAG6000, in a single faceplate. In
addition, it also supports operation and monitoring via Touch
Panels as well as the integration in SIMATIC S7 applications. The
SITRANS Library is based on the modern design of the Advanced Process Library (APL). Together with the APL, the
SITRANS Library enables you to create harmonic solutions with
a consistent look & feel and optimum use of the functions of the
SITRANS field devices in many industries.
8
It helps accelerate the engineering process, reduces the timeto-market, and simplifies process control. In addition, operator
functions (such as "Dosing") and process-related diagnostic information (such as empty pipe detection and flow direction) are
provided.
Note:
SITRANS Library can be used in combination with
SIMATIC PCS 7 version V8.0 and higher.
■ Application
The total solution described can be used in the following sectors
of the process industry:
• Chemical industry
• Pharmaceutical industry
• Water and wastewater
• Glass and solar
• Oil & gas
• Food and beverage industry
• Minerals and mining
8/22
Siemens FI 01 · 2015 US Edition
■ Function
SITRANS Library for SIMATIC PCS 7
Sublibrary for the functional expansion of the SIMATIC PCS 7
Advanced Process Library with:
• Function blocks and faceplates for the SITRANS F M
MAG 6000 DP with dosing function for SIMATIC S7-400,
SIMATIC S7-300 and panel interface blocks
• Function blocks and faceplates for SITRANS field devices for
SIMATIC S7-400 and SIMATIC S7-300 with WinCC.
The function blocks are configured in CFC.
Control and monitoring from a panel is configured with the panel
interface blocks for example for the SITRANS F M MAG 6000 DP.
Taking operating rights and hierarchical operating concepts
(multi-control room operation) into consideration, the technological function can then be operated from both an operator station
and a Touch Panel.
Detailed information for which field devices which systems and
system versions are supported see under
http://support.automation.siemens.com/WW/view/en/85285872
■ Selection and Ordering Data
Article No.
SITRANS Library
Block library for SIMATIC PCS 7 V8.0 and
SIMATIC S7 with function blocks and face
plates as well as electronic documentation
Engineering software, software class A, two
languages (English, German), runs under
opreation system
Windows XP Professional 32 Bit,
Windows 7 Ultimate 32/64 Bit,
Windows Server 2003 R2 Standard 32 Bit or
Windows Server 2008 R2 Standard 64 Bit,
single license for 1 installation
• Engineering license for one customer plant.
Delivery form: can be downloaded, with certificate of license
7MP2990-0AA00