© Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E ■ Overview ■ Mode of operation The flow measuring principle is based on Faraday’s law of electromagnetic induction according to which the sensor converts the flow into an electrical voltage proportional to the velocity of the flow. ■ Function The TRANSMAG 2 is a microprocessor-based transmitter with a build-in alphanumeric display in several languages. The transmitters evaluate the signals from the associated electromagnetic sensors and also fulfil the task of a power supply unit which provides the magnet coils with a constant current. The magnetic flux density in the sensor is additionally monitored by reference coils. Further information on connection, mode of operation and installation can be found in the data sheets for the sensors. Displays and keypad SITRANS F M TRANSMAG 2 with the SITRANS F M 911/E sensor is a pulsed alternating field magnetic flowmeter where the magnetic field strength is much higher than conventional DC pulsed magnetic flowmeters. Operation of the transmitter can be carried out using: • Keypad and display unit • HART communicator • PC/laptop and SIMATIC PDM software via HART communication • PC/laptop and SIMATIC PDM software using PROFIBUS PA communication ■ Benefits • Wide range of sizes DN 15 to DN 1000 (½" to 40") • Broad range of liner and electrode materials for extreme process medias • Fully welded construction provides a ruggedness that suits the toughest applications and environments. • Automatic reading of SmartPLUG for easy commissioning • Simple menu operation with two-line display • Comprehensiv self-diagnostic with selfmonitoring and internal simulation ■ Application The main applications of the SITRANS F M transmitter TRANSMAG 2 can be found in the following sectors: • Pulp and Paper industry • Mining industry The pulse alternating field technology is ideal for difficult applications like: • High concentrated paper stock > 3 % • Heavy mining slurries • Mining slurries with magnetic particles. • Low conductive medias 1 S/cm (0.1 S/cm depending on medium) min. 230 Ω Operating and display panel PC/ laptop HART communicator Coupling module RS 232 HART communication PROFIBUS DP Master PROFIBUS PA + Coupler with power supply T Bus term. ....... Transmitter with PROFIBUS PA interface PROFIBUS PA communication ■ Design • Available for remote mounting • PROFIBUS PA (profile 2.0) / HART communication • Analog output and digital outputs for pulses, device status, limits, flow direction, frequency output Siemens FI 01 · 2016 3/105 3 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E ■ Technical specifications Output configuration Transmitter TRANSMAG 2 • Pulse Mode of operation and design Measuring principle Magnetic field excitation 3 Electromagnetic with pulsed alternating field (PAC) Automatic power supply synchronization - 50 Hz AC power supply Bipolar (16.7 Hz) Bipolar with prepulse (10 Hz) Unipolar (8.33 Hz) - 60 Hz AC power supply Bipolar (20 Hz) Bipolar with prepulse (12 Hz) Unipolar (10 Hz) - Pulse significance 5000 pulses/s - Pulse width 0.1 ms • Limit frequency 10000 Hz • Limits Limits for flow and quantity, flow direction, alarm Digital output 2 (relay) (only 7ME5034-0.…) Relay NC or NO function Accuracy under reference conditions • Rating Max. 5 W, max. 50 V AC/DC, max. 200 mA Measuring tolerance of pulse output • Output configuration Limits for flow and quantity, flow direction, alarm • With v > 0.25 m/s (0.82 ft/s) 0.5 % of measured value 1.2 mm/s (0.05 inch/s) • With v < 0.25 m/s (0.82 ft/s) 2.5 mm/s (0.1 inch/s) Digital input (optional to digital output 2) (only 7ME5034-2.…) Measuring tolerance of analog output As pulse output plus 0.1 % conversion error 20 µA • Input function configurable as high-active or low-active Set measured value or counter to zero Repeatability 0.2 % of measured value • Signal voltage Max. 30 V DC, Ri = 3 k: High level: +11 ... +30 V DC Low level: -30 ... +5 V DC Reference conditions • Process temperature 25 °C 5 °C (77 °F 9 °F) • Ambient temperature 25 °C 5 °C (77 °F 9 °F) • Warm-up time Min. 30 min • Installation conditions Inlet pipe section 10 x DN Outlet pipe section 5 x DN Installed centered in pipe • Medium Water without gaseous or solid components Calibration Standard production calibration, calibration report shipped with sensor For PROFIBUS devices PROFIBUS PA (for PROFIBUS-devices 7ME5034-1….) • Communication Layer 1 and 2 according to PROFIBUS PA Transmission according to IEC 1158-2 Layer 7 (protocol layer) according to PROFIBUS PA and DP V1 (EN 50170) Device class B, device profile 2.0 Max. 4 simultaneous C2 connections • Bus voltage 9 ... 32 V DC permissible • Current consumption from bus 10 mA; limited to 15 mA in event of fault by electrical current limitation Zero-point, 2 x 25 % and 2 x 90 % Output Electrical isolation Outputs electrically isolated from one another and from the power supply, max. 60 V permissible against PE/equipotential bonding Current output 0/4 ... 20 mA (7ME5034-0…. or 7ME5034-2….) Rated operating conditions Installation conditions See also sensor Ambient temperature • Signal - Upper limit 0/4 … 20 mA, selectable • Operation -20 ... +60 °C (-4 ... +140 °F) - Failure 20 … 22.5 mA, optional 3.6; 20 or 24 mA • Display module 0 ... 50 °C (32 ... 122 °F) Storage -25 ... +80 °C (-13 ... +176 °F) Degree of protection IP67/NEMA 4X • Load - Output max. 600 , max. load voltage 15 V DC - For HART communication 250 Communication • Protocol Via analog output with PC coupling module or HART communicator HART, version 5.1 Digital output Signal • Output Configurable as active or passive signals - Active signal 24 V DC, 24 mA, Ri = 170 - Passive signal Open collector, max. 30 V DC, 200 mA 3/106 Siemens FI 01 · 2016 Electromagnetic compatibility (EMC) • Emitted interference To IEC/EN 61326 for use in industrial areas • Noise immunity To IEC/EN 61326 for use in industrial areas © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Medium conditions • Process temperature -20 ... +150 °C (-4 ... 302 °F) depending on the liner Minimum conductivity of medium • With SITRANS F M 911/E sensors 1 µS/cm (0.1 µS/cm depending on medium) Design Weight of transmitter 4.4 kg (9.7 lb) Remote version Transmitter must be connected to sensor using shielded cable Maximum cable length 100 m (328 ft) Housing Die-cast aluminum, painted Displays and keypad General display LCD, backlid, two lines with 16 characters each Multi-display for Flow, totalizer, flow velocity Keypad 4 keys for entering parameters Power supply corresponding to rating plate Selection and Ordering data Article No. SITRANS F M electromagnetic transmitter TRANSMAG 2 for alternating field, remote version, 110 ... 230 V AC 7 ME 5 0 3 4 - 7AA7 1 - 7AA 0 Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Output/communication 4 ... 20 mA with HART protocol PROFIBUS PA connection 4 ... 20 mA with HART protocol, digital input 0 1 2 Operator display and keypad Without With 0 1 Cable glands M20/M16 x 1.5 ½“ NPT 1 2 Order code Selection and Ordering data • AC supply 100 ... 250 V AC 15 %, 47 ... 63 Hz • Power consumption Approx. 120 ... 630 VA, depending on sensor Line fuse 100 ... 230 V AC: T1.6A Magnet current fuse F5A/250 V Sensor cables between sensor and transmitter The signal voltage proportional to the flow and present at the electrodes of the EMF is only a few µV to mV. Superimposed on this are electrochemical interferences resulting from the contact between the electrodes and liquid, and which can be up to several Volt. Also frequently superimposed are line frequency interferences, interferences resulting from vibrations on the pipelines or signal cables, as well as strong magnetic fields in the vicinity. Sufficient shielding must therefore be provided, as well as fixed routing of the signal cables (electrode and magnet current cable) in the case of remote versions. This also applies to devices with integral preamplifier (smartPLUG). The cable length between the sensor and transmitter must not exceed 100 m (328 ft). Attention must also be paid to the cable routing. Signal cables must be routed free of vibration, and protected against strong magnetic and stray fields. In case of doubt, the sensor cables must be routed in grounded steel conduit. 3 Additional information Please add “-Z“ to Article No. and specify Order code(s) and plain text. Strengthened mounting bracket for wall and pipeline installation A02 Measuring range, specify in plain text: Y01: 0 to ... m3/h Y01 Pulse significance, specify in plain text: Y02: 0 to ... pulses/l Setting of digital outputs, specify in plain text: Y03: Setting of digital outputs: ... Y02 Measuring-point number (max. 8 characters), specify in plain text: Y15: .......... Y15 Measuring-point description (max. 16 characters), specify in plain text: Y16: .......... Y16 Stainless steel tag plate Y17 Other post-production requirements (add plain text) Y99 Y03 Operating instructions for SITRANS F M TRANSMAG 2 Description Article No. • English A5E00102775 • German A5E00192774 This device is shipped with a Quick Start guide and a CD containing further SITRANS F literature. All literature is available to download for free, in a range of languages, at www.siemens.com/processinstrumentation/documentation Siemens FI 01 · 2016 3/107 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Accessories 3 Spare parts Description Article No. Description Article No. Standard wall mounting bracket. Steel AISI 316L/ EN10088-2-1.4404 7ME5933-0AC04 Operating/Display module 7ME5933-0AC00 Special wall-/pipe mounting bracket kit. BI 2.5 DIN 59382 X6Cr17 7ME5933-0AC05 Potting kit for terminal box FDK:085U0220 of flow sensors for IP68/NEMA 6P We can offer shorter delivery times for configurations designated with the Quick Ship Symbol . For details see page 9/5 in the appendix. Electronics cover with glass 7ME5933-0AC01 plate (non Ex). Die cast aluminum, with corrosion-resistant Basic Polyester powder coating (min. 60 m) Cover for sensor cable and gasket. Die cast aluminum, with corrosion-resistant Basic Polyester powder coating (min. 60 m) 7ME5933-0AC02 Cover for mains supply/communication. Die cast aluminum, with corrosion-resistant Basic Polyester powder coating (min. 60 m) 7ME5933-0AC03 Safety clamp for electronic cover with glass plate (7ME5933-0AC01) 7ME5933-0AC06 M20 cable gland set for power and output connection, gray PA plastic, 2 pcs. • cables Ø 6 ... 12 mm (0.24" ... 0.47") • -40 ... +100 °C (-40 ... +212 °F) A5E02246350 1/2" NPT cable gland set for A5E02246396 power and output connection, gray PA plastic, 2 pcs. • cables Ø 6 ... 12 mm (0.24" ... 0.47") • -40 ... +100 °C (-40 ... +212 °F) M16 x 1.5 cable gland set for A5E02246369 sensor connection, brass chrome, 2 pcs. and 2 pcs. blind • cables Ø 5 ... 9 mm (0.20" ... 0.35") • -20 ... +105°C (-4 ... +221 °F) 3/108 Siemens FI 01 · 2016 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E ■ Dimensional drawings ■ Schematics 70 (2.76) Transmitter 1 2 150 (5.91) 90 (3.54) Power supply L/N PE conductor 95 (3.74) 90 (3.54) 7 8 SITRANS F M transmitter TRANSMAG 2 with wall mounting bracket, dimensions in mm (inch) 92 (3.62) 100 ... 230 V AC ±15% 47-63 Hz 0/4 ... 20mA Load 600 Ω max. 15 V 7 8 5 6 205 (8.07) Power supply Digital output 1 5 active 24 V DC max. 24 mA Ri 170 Ω 6 (active/passive) Passive open collector max. 30 V DC 200 mA 150 (5.91) 248 (9.76) 89 (3.50) 105 (4.13) Sensor connection 154 (6.06) Ø80 (3.15) SITRANS F M transmitter TRANSMAG 2 with wall and pipeline mounting bracket, dimensions in mm (inch) PROFIBUS Digital output 1 Passive open collector max. 30 DC 100 mA Digital output 2 (Relay) NC/NO max. 5W, 50 V DC, 200 mA or Digital input High +11 ... +30 V DC Low -30 ... +5 V DC 153 (6.02) 5 6 7 7 8 Coil cable Magnetic fieldcorrent 1 Magnetic fieldcorrent 2 PE Sensor 5 6 7 brown white green/yellow 29 22 30 SmartPlug connect Supply (-6V) Ground (0V) Supply (+6V) 29 22 30 green red/orange blue 23 24 Electrode connect Electr. 1 (EL 1) Electr. 2 (EL 2) 23 24 brown white 55 66 Reference coil Ref. 1 Ref. 2 55 66 black/gray yellow SITRANS F M transmitter TRANSMAG 2, connection diagram Siemens FI 01 · 2016 3/109 3 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E 911/E sensor Protection rings for liners Process connection Nominal diameters DN 15 ... 1000 (½" ... 40") Metering tube connections EN 1092-1, ANSI B16.5, AWWA C-207 and JIS 10 K Rated operating conditions 3 Function To protect the edges of liners from abrasion (e.g. gravel, sand etc.). Used mainly with soft rubber liners and for PTFE liners at high temperatures from 100 to 150 °C (212 to 302 °F). Installation conditions See system information Contact with medium Yes, please always check resistance to measured medium. • Soft rubber liner 0 ... 70 °C (32 ... 158 °F) Material • Hard rubber liner 0 ... 90 °C (32 ... 194 °F) Option: 100 °C (212 °F) Stainless steel AISI 316Ti/1.4571, optionally Hastelloy C276/2.4819 • PTFE liner • -20 ... +150 °C (-4 ... +302 °F) at 25 bar (363 psi) • -20 ... +100 °C (-4 ... +212 °F) at 40 bar (580 psi) • Linatex (rubber) liner -40 ... +70 °C (-40 ... +158 °F) (for temperatures below -20 °C (-4 °F) AISI 316L/1.4404 flanges must be used) • Novolak liner 130 °C (266 °F) at 40 bar (580 psi) Degree of protection IP67/NEMA 4X Optional IP68/NEMA 6 Material thickness The overall length of the sensor is increased by •6 mm for DN 15 to DN 150 (0.24“ for ½“ to 6“) or •10 mm for DN 200 to DN 600 (0.4“ for 8“ to 24“) Standard Optional for all liners. Must be ordered separately. Article No. 7ME5912-...., 7ME5943-... Grounding rings Function Electrical reference and grounding of the medium. Required if the pipelines are not electrically conducting or are lined (plastic pipelines, concrete pipelines etc.). All grounding rings must be connected to the grounding screw present on the sensor. Contact with medium Yes, please always check resistance to measured medium. Material Stainless steel AISI 316Ti/1.4571 or Hastelloy C4/2.4610 Medium conditions Maximum flow velocity 12 m/s (39.4 ft/s) Full scale value of flow velocity 0.15 ... 12 m/s (0.49 ... 39.4 ft/s) Design Weight See dimensional drawings Flange and housing material Mild steel (1.0460/1.0570, with corrosion resistant two component epoxy coating (min. 150 m) or AISI 316L/1.4404 flanges and carbon steel housing, with corrosionresistant two-component epoxy coating (min. 150 m) Measuring pipe material Stainless steel AISI 304 or higher Electrode material • AISI 316Ti/1.4571 • PTFE: Hastelloy C276/2.4819 • Platinum • Titanium • Tantalum Grounding electrode material 3/110 Siemens FI 01 · 2016 Defined via the Order code Material thickness The overall length of the sensor is increased by 2 mm (0.08“) per grounding ring. Standard Optional for all liners. Required between the medium and sensor for equipotential bonding between nonconducting pipelines or lined pipelines. Article No. 7ME5902-...., 7ME5942-... Important: The rings must be ordered together with the sensor. Gaskets are not included. In case of replacement please include the sensor MLFB code on the order. © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Notes on pressure equipment directive The devices are designed for liquids of danger group "Gases of fluid group 1". The categories differ according to the version, and are listed in the table below. The minimum temperature is defined at -10 °C (14 °F) for the flange materials C22.8 (1.0460). The minimum temperature is defined at -20 °C (-4 °F) for the flange material 1.4404/316L. For further information on the PED standard and requirements, see page 9/6. Classification according to pressure equipment directive (PED 2014/68/EU) Nominal diameter Nominal pressure DN (inch) PN (MWP psi) Permissible media Category 15 ... 25 (½" ... 1") 40 200 ... 300 (8" ... 12") 10 (580) Gases fluid group 1 and liquids fluid group 1 Article 4.3 (145) Gases fluid group 1 and liquids fluid group 1 65 ... 250 (2½" ... 10") II 16 (232) Gases fluid group 1 and liquids fluid group 1 40 ... 100 II (1½" ... 4") 40 (580) Gases fluid group 1 and liquids fluid group 1 II 350 ... 1000 (14" ... 40") 10 (145) Gases fluid group 1 and liquids fluid group 1 III 300 ... 1000 (12" ... 40") 16 (232) Gases fluid group 1 and liquids fluid group 1 III 200 ... 600 (8" ... 24") 25 (363) Gases fluid group 1 and liquids fluid group 1 III 125 ... 600 (5" ... 24") 40 (580) Gases fluid group 1 and liquids fluid group 1 III Siemens FI 01 · 2016 3 3/111 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Selection and Ordering data Article No. Selection and Ordering data Flowsensor SITRANS F M 911/E 7 ME 5 6 1 0 - Additional information 77777 - 7AA7 Please add “-Z“ to Article No. and specify Order code(s) and plain text. Click on the Article No. for the online configuration in the PIA Life Cycle Portal. 3 Order Code Two grounding electrodes made of stainless steel AISI 316Ti/1.4571 A02 1V 2D 2R Two grounding electrodes made of Hastelloy C276/2.4819 A04 Two grounding electrodes made of Platinum A05 DN 50 (2") DN 65 (2½") DN 80 (3") 2Y 3F 3M Two grounding electrodes made of Titanum A06 Two grounding electrodes made of Tantalum A07 Factory certificate to EN 10204-2.2 3T 4B 4H C14 DN 100 (4") DN 125 (5") DN 150 (6") Acceptance test B to DIN 50049, section 3.1 and EN 10204 C16 DN 200 (8") DN 250 (10") DN 300 (12") 4P 4V 5D Power supply 110 V/60 Hz P01 Tag name plate, stainless steel, add plain text Y17 Other postproduction requirements, add plain text Y99 DN 350 (14") DN 400 (16") DN 450 (18") 5K 5R 5Y DN 500 (20") DN 600 (24") DN 700 (28") 6F 6P 6Y DN 800 (32") DN 900 (36") DN 1000 (40") 7H 7M 7R Nominal diameter DN 15 (½") DN 25 (1") DN 40 (1½") Flange norm and pressure rating EN 1092-1, PN 10 (DN 200 ... 1000 (8" ... 40")) EN 1092-1, PN 16 (DN 65 ... 1000 (2½" ... 40")) EN 1092-1, PN 25 (DN 200 ... 1000 (8" ... 40")) EN 1092-1, PN 40 (DN 15 ... 1000 (½" ... 40")) B C E F ANSI B16.5, Class 150 (½" ... 24")1) ANSI B16.5, Class 300 (½" ... 24")2) J K AWWA C-207 Class D (28" ... 40") JIS 10 K (½" ... 24") L R Flange material Mid steel flanges 1.0460/1.0570 Stainless steel flanges, AISI 316L/1.4404 Liner material Soft rubber (DN 25 to DN 1000) PTFE (DN 15 to DN 600) Hardrubber (DN 15 to DN 1000) Linatex (DN 40 to DN 1000) Novolak (sealing material FFKM) (DN 50 to DN 1000) Electrode material AISI 316Ti/1.4571 Hastelloy C276/2.4819 Platinum Titanium Tantalum Cable glands/terminal box Metric: Polyamide terminal box ½" NPT: Polyamide terminal box Metric: Stainless steel terminal box ½" NPT: Stainless steel terminal box 3/112 Siemens FI 01 · 2016 1) 20 °C (68 °F), max. 19.6 bar (285 psi) for steel flanges and max. 15.9 bar (231 psi) for stainless seel flanges 2) 20 °C (68 °F), max. 51.1 bar (741 psi) for steel flanges and max. 41.4 bar (600 psi) for stainless seel flanges Selection and Ordering data Article No. Order code SITRANS F M TRANSMAG 2 and sensor 911/E 7 ME 5 9 3 0 - Cable 5 7A 0 0 - 0 AA 0 777 Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Cable kit for sensor 911/E with alternating field, Magnet current cable 3 x 1.0 mm2 (3 x 0.0016 inch2), electrode/reference cable 7 x 0.5 mm2 (7 x 0.0008 inch2) with shield PVC • Length: 5 m (16.4 ft) • Length: 10 m (32.8 ft) • Length: 20 m (65.6 ft) • Length: 30 m (98.4 ft) • Other length (specify in plain text): max. 100 m (328 ft) 1 3 1 3 4 5 6 1 2 3 4 5 1 2 3 4 B C D E Z J1Y © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Selection and Ordering data Article No. Order code SITRANS F M electromagnetic flowmeter Protection ring for flow sensor 911E (per pair). Gaskets not included. 7 ME 5 9 1 2 - 7777 777 Protection rings for flow sensor 911E (per pair) 7 ME 5 9 4 2 - 77777 Grounding rings for flow sensor 911E (per unit) 7 ME 5 9 4 3 - 77777 Click on the Article No. for the online configuration in the PIA Life Cycle Portal. 1 7 0 Nominal diameter for PTFE, mat. no. 1.4571/316 Ti DN 15 (½") DN 25 (1") AA CA DN 40 (1½") DN 50 (2") EA FA DN 65 (2½") DN 80 (3") DN 100 (4") GA HA JA DN 125 (5") DN 150 (6") DN 200 (8") KA LA MA DN 250 (10") DN 300 (12") NA PA Other nominal diameters: specify in plain text ZA for Hard/Soft rubber, Novolak, mat. no. 1.471/316 Ti DN 15 (½") DN 25 (1") AB CB DN 40 (1½") DN 50 (2") EB FB DN 65 (2½") DN 80 (3") DN 100 (4") GB HB JB DN 125 (5") DN 150 (6") DN 200 (8") KB LB MB DN 250 (10") DN 300 (12") NB PB Other nominal diameters: specify in plain text ZB Flange design Flange to DIN Flange to ANSI Flange to JIS Order code Gaskets not included. Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Liner Hard rubber/soft rubber/Linatex Novolak PTFE Article No. Selection and Ordering data J1Y J1Y 1 2 3 Nominal diameter DN 15 (½") DN 25 (1") DN 40 (1½") 1V 2D 2R DN 50 (2") DN 65 (2½") DN 80 (3") 2Y 3F 3M DN 100 (4") DN 125 (5") DN 150 (6") 3T 4B 4H DN 200 (8") DN 250 (10") DN 300 (12") 4P 4V 5D DN 350 (14") DN 400 (16") DN 450 (18") 5K 5R 5Y DN 500 (20") DN 600 (24") DN 700 (28") 6F 6P 6Y DN 800 (32") DN 900 (36") DN 1000 (40") 7H 7M 7R 3 Flange design EN 1092-1, PN10 EN 1092-1, PN16 B C EN 1092-1, PN25 EN 1092-1, PN40 E F AISI B16.5, class 150 AISI B16.5, class 300 J K AWWA C-207, class D JIS B2220, 10K L R Material Stainless steel AISI 316Ti/1.4571 Hastelloy C4/2.4610 1 2 Flange design Soft rubber PTFE Hard rubber 1 3 4 Linatex Novolak 5 6 Siemens FI 01 · 2016 3/113 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E Selection and Ordering data Article No. Order code SITRANS F M electromagnetic flowmeter Grounding rings for flow sensor 911E (per unit). Gaskets not included. 7 ME 5 9 0 2 - 7777 777 Click on the Article No. for the online configuration in the PIA Life Cycle Portal. 3 Liner Hard rubber/soft rubber Novolak PTFE 1 7 0 Nominal diameter Mat. no. 1.4571/316 Ti DN 15 (½") DN 25 (1") AA CA DN 40 (1½") DN 50 (2") EA FA DN 65 (2½") DN 80 (3") DN 100 (4") GA HA JA DN 125 (5") DN 150 (6") DN 200 (8") KA LA MA DN 250 (10") DN 300 (12") DN 350 (14") NA PA QA DN 400 (16") DN 500 (20") DN 600 (24") RA SA TA DN 700 (28") DN 800 (32") DN 900 (36") DN 1000 (40") UA VA WA XA Other nominal diam.: specify in plain text ZA Material Hastelloy C4/2.4610 DN 15 (½") DN 25 (1") AB CB DN 40 (1½") DN 50 (2") EB FB DN 65 (2½") DN 80 (3") DN 100 (4") GB HB JB DN 125 (5") DN 150 (6") DN 200 (8") KB LB MB DN 250 (10") DN 300 (12") DN 350 (14") NB PB QB DN 400 (16") DN 500 (20") DN 600 (24") RB SB TB Other nominal diam.: specify in plain text ZB Flange design Flange to DIN Flange to ANSI Flange to JIS 3/114 Siemens FI 01 · 2016 J1Y J1Y 1 2 3 © Siemens AG 2016 Flow Measurement SITRANS F M Transmitter TRANSMAG 2 with sensor 911/E ■ Dimensional drawings 131 (5.16) 155 (6.1) A 3 D1 B L D SITRANS F M flow sensor 911/E, remote version, dimensions in mm (inch) Build-in length 911/E [in mm and inch] Nominal diameter DN 15 ½“ DN 25 1“ DN 40 1 ½“ DN 50 2“ DN 65 2 ½“ DN 80 3“ DN 100 4“ DN 125 5“ DN 150 6“ DN 200 8“ DN 250 10“ Build-in length L1) Hard rubber version Linatex/soft rubber version 270 (10.63) 280 (11.02) 330 (12.99) 340 (13.39) 370 (14.57) 410 (16.14) 470 (18.50) PTFE-liner without protection rings 270 (10.63) 280 (11.02) 330 (12.99) 340 (13.39) 370 (14.57) 410 (16.14) 470 (18.50) - 275 (10.83) 325 (12.79) 362 (14.25) 401 (15.79) 460 (18.11) Novolak-version 335 (13.19) 333 (13.11) Dimensions of sensor housing Housing width B Height A 170 (6.69) 240 (9.45) 206 (8.11) 222 (8.74) 229 (9.02) 262 (10.32) 274 (10.79) 286 (11.26) 299 (11.78) 334 (13.15) 358 (14.10) 135 (5.35) 167 (6.58) 182 (7.17) 247 (9.73) 272 (10.71) 296 (11.65) 322 (12.68) 392 (15.43) 440 (17.32) Housing diameter D1 Weight of PN16 version in kg 8.0 (MWP 232 psi version in lb) approx. (17.64) 8.5 (18.74) 11.5 (25.35) 25.0 (55.12) 26 (57.32) 27 (59.53) 28 (61.73) 34 (74.95) 38 (83.78) 68 (149.9) 81 (178.6) Nominal diameter DN 300 12“ DN 350 14“ DN 400 16“ DN 450 18“ DN 500 20“ DN 600 24“ DN 700 28“ DN 750 30“ DN 800 32“ DN 900 36“ DN 1000 40“ Hard rubber version Linatex/soft rubber version 500 (19.68) 550 (21.65) 600 (23.62) 650 (25.59) 650 (25.59) 780 (30.71) 1040 (40.95) 1170 (46.06) 1300 (51.18) PTFE-liner without protection rings 500 (19.68) 550 (21.65) 600 (23.62) 660 (25.98) 650 (25.59) 780 (30.71) Novolak-version 489 (19.25) 538 (21.18) 592 (23.31) 638 (25.12) 638 (25.12) 772 (30.39) 1033 (40.63) 1163 (45.79) 1293 (50.91) Housing width B 240 (9.45) 225 (8.86) 250 (9.84) 270 (10.63) 300 (11.81) 360 (14.17) 500 (19.69) 560 (22.05) 620 (24.41) Height A 383 (15.08) 375 (14.76) 400 (15.75) 433 (17.05) 453 (17.84) 505 (19.88) 558 (21.97) 590 (23.23) 608 (23.94) 658 (25.91) 713 (28.07) Housing diameter D1 490 (19.29) 474 (18.66) 524 (20.63) 591 (23.26) 629 (24.76) 734 (28.90) 839 (33.03) 904 (35.59) 939 (36.97) 1039 (40.91) 1150 (45.28) Weight of PN10 Version in kg 95 (MWP 145 psi version in lb) approx. (209.4) 118 (260.2) 161 (354.9) 185 (407.9) 233 (513.7) 401 (884.1) 420 (925.9) 450 (992.1) 500 560 620 (1102.3) (1234.6) (1366.9) Build-in length L1) 910 (35.83) 903 (35.55) Dimensions of sensor housing 1) 420 (16.54) Tolerance for build-in lenght: L + 0.0/-4.0 mm (+0.00/-0.157 inch) With protection rings for > DN25 + 6.0 mm, > DN200 + 10.0 mm (> 1” + 0.236 inch, > 8” + 0.394 inch) Siemens FI 01 · 2016 3/115