Application Manual for NEMA Motors Section 1 Index of Products Part 1 Part 2 Page NEMA Frames Totally Enclosed Fan Cooled 1 Open Drip Proof 2 Construction Features DP10 3 RGZVMTESD 15 RGZP 4 RGZZVMTESD 16 RGZPSD 5 RGZVILESD 17 RGZESD 6 RGZZVILESD 18 RGZZESD 7 GP10A 19 RGZESDI 8 GP10 20 RGZZESDI 9 SD10 21 RGZEESD 10 GP100A 22 RGZEESDX 11 GP100 23 HSRGZVESD 12 SD100 24 RGZVESD 13 SD100 IEEE841 25 RGZZVESD 14 Section 1 Part 1 Section Page 1 1 of 25 Part 104/08 Page 1/2 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors NEMA Frame TEFC Motors 600 Volts and Below Product Range and Scope by Frame Size SPEED HP 3600 1800 1200 900 1 143 143 145 182 1.5 143 145 182 184 2 145 145 184 213 3 182 182 213 215 5 184 184 215 254 7.5 213 213 254 256 10 215 215 256 284 15 254 254 284 286 20 256 256 286 324 25 284 284 324 326 30 286 286 326 364 40 324 324 364 365 50 326 326 365 404 60 364 364 404 405 444 75 365 365 405 444 445 100 405 405 444 445 447 125 444 444 445 447 449 150 445 445 447 447 449 200 447 447 449 449 250 449 449 449 S449 300 449 447 S449 350 S449 S449 400 S449 S449 720 Section 1 Part 1 Section Page 1 2 of 25 Part 104/08 Page 2/2 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors NEMA Frame ODP Motors 600 Volts and Below Product Range and Scope by Frame Size SPEED HP 3600 1 1800 1200 143 145 900 1.5 143 145 182 2 145 145 184 3 145 182 213 5 182 184 215 7.5 184 213 254 10 213 215 256 15 215 254 284 20 254 256 286 25 256 284 324 30 284 286 326 40 286 324 364 50 324 326 365 60 326 364 404 75 364 365 405 100 365 404 444 445 125 404 405 445 447 150 405 444 447 447 200 444 445 447 449 250 445 445 449 300 447 447 449 350 447 447 400 449 449 500 449 449 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data DP10 Open Drip Proof Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields echanical Data Conduit Box General Purpose - ODP High 1-500 140-440 60 Hertz 3 - Phase 208-230/460 to 100HP (400 frame) 460 only 100HP (440 frame) and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 (140-400) and Part 30 (440) Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast Iron Cast Iron Lead Seal Gasket Fan Cover 140-400 Steel 440 Cast Iron Neoprene Not Applicable Cooling Fan Not Applicable Rotor Shaft Bearing Type Die Cast Aluminum High Strength Carbon Steel (C1045) 140-280 Lubricated for Life 320-440 Double Shielded 320-440 Stationary Bearing Caps Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings 140-400 Lithium 440 Polyurea 320-440 Alemite Lube Relief Fittings Condensation Drain Plug Hardware Lifting Eyebolt Zinc Plated 180-440 Included Nameplate Paint Epoxy Enamel RAL 7030 Grey Vibration 0.15 IPS Stainless Steel - Engraved Section 1 Part 2 Section Page 1 3 of 25 Part 204/08 Page 1 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZP General Purpose - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Fan Cover Mechanical Data Cooling Fan Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings General Purpose - TEFC High 1-200 140-440 60 Hertz 3 - Phase 230/460 460 only 100HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 30 Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast Iron 140-250 Aluminum 280-440 Cast Iron 140-250 Aluminum 280-400 Steel, 440 Cast Iron Neoprene 140-365 Polycarbonate 400-440 Cast Iron Bi-directional, Polypropylene Die Cast Aluminum High Strength Carbon Steel (C1045) 140-250 Double Shielded 280-440 Single Shielded 440 Stationary Bearing Caps 280-440 V-Ring Slinger DE 140-250 Lubricated for Life 280-440 Polyurea 280-440 Alemite Nameplate Paint 280-440 Plug 140-360 Hole 400-440 T-Drain Zinc Plated 140-180 Provisions 210-440 Included Aluminum - Engraved Epoxy Enamel - RAL 7030 Grey Vibration 0.08 IPS Lube Relief Fittings Condensation Drain Hardware Lifting Eyebolt Section 1 Part 2 Section Page 1 4 of 25 Part 204/08 Page 2 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZPSD Severe Duty - TEFC Warranty Frame End Shields Severe Duty - TEFC High 1-200 140-440 60 Hertz 3 - Phase 230/460 460 only 100HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 30 Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Neoprene Cast Iron Cooling Fan Bi-directional, Polypropylene Rotor Shaft Bearing Type Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Lubrication 400-440 Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T-Drain Hardware Lifting Eyebolt Nameplate Paint Zinc Plated 140-180 Provisions 210-440 Included Stainless Steel - Engraved Epoxy Enamel RAL 7030 Grey Vibration 0.08 IPS Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Mechanical Data Temperature Rise (sine wave) Section 1 Part 2 Section Page 1 5 of 25 Part 204/08 Page 3 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZESD Severe Duty – TEFC Warranty Frame End Shields Severe Duty - TEFC High 1-400 140-S440 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Neoprene Cast Iron Cooling Fan 140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Mechanical Data Temperature Rise (sine wave) Rotor Shaft Bearing Type Lubrication Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T-Drain Hardware Lifting Eyebolt Nameplate Paint Zinc Plated 140-180 Provisions 210-440 Included Stainless Steel - Engraved Epoxy Enamel RAL 7030 Grey Vibration 0.08 IPS Bearing Inner Cap Shaft Seal / Slinger Section 1 Part 2 Section Page 1 6 of 25 Part 204/08 Page 4 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZZESD Hazardous Duty – TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Mechanical Data Temperature Rise (sine wave) Hazardous Duty - TEFC High 1-300 140-440 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1 NEMA design B Copper - Random Wound Class F Warranty Frame End Shields Class B @ 1.0SF 3 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Cast Iron Cooling Fan Bi-directional, Polypropylene Rotor Shaft Bearing Type Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Lubrication Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug 400-440 Only Hardware Lifting Eyebolt Nameplate Paint Zinc Plated 140-180 Provisions 210-440 Included Stainless Steel - Engraved Epoxy Enamel - RAL 7030 Grey Vibration 0.08 IPS Section 1 Part 2 Section Page 1 7 of 25 Part 204/08 Page 5 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZESDI Severe/Inverter Duty – TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Severe / Inverter Duty - TEFC High 1-400 140-S440 60 Hertz 3 - Phase 460 Service Factor (sine wave) Electrical Design Stator Windings Insulation Warranty Frame End Shields 1.15 (sine wave), 1.0 (VFD) NEMA design B (except for derates) Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF & Class F @ 1.15SF 3 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Neoprene Cast Iron Cooling Fan Bi-directional, Polypropylene Rotor Shaft Bearing Type Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Lubrication Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T-Drain Hardware Lifting Eyebolt Nameplate Paint Zinc Plated 140-180 Provisions 210-440 Included Stainless Steel - Engraved Epoxy Enamel - RAL 7030 Grey Vibration 0.06 IPS Mechanical Data Temperature Rise (sine wave) Section 1 Part 2 Section Page 1 8 of 25 Part 204/08 Page 6 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZZESDI Hazardous/Inverter Duty – TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Hazardous / Inverter Duty - TEFC High 1-200 140-440 60 Hertz 3 - Phase 460 Service Factor (sine wave) Electrical Design Stator Windings Insulation Warranty Frame End Shields 1 NEMA design B (except for derates) Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF 3 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Cast Iron Cooling Fan Bi-directional, Polypropylene Rotor Shaft Bearing Type Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Lubrication Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug 400-440 Only Hardware Lifting Eyebolt Nameplate Paint Zinc Plated 140-180 Provisions 210-440 Included Stainless Steel - Engraved Epoxy Enamel - RAL 7030 Grey Vibration 0.06 IPS Mechanical Data Temperature Rise (sine wave) Section 1 Part 2 Section Page 1 9 of 25 Part 204/08 Page 7 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZEESD Severe Duty – TEFC Warranty Frame End Shields Severe Duty - TEFC NEMA Premium 1-400 140-S440 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B (except as noted) Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Neoprene Cast Iron Cooling Fan Rotor Shaft Bearing Type 140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Stationary Bearing Caps V-Ring Slinger DE & ODE Lubrication Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T-Drain Hardware Lifting Eyebolt Zinc Plated 140-440 Included Nameplate Paint Stainless Steel - Engraved Epoxy Enamel - RAL 7030 Grey Vibration 0.08 IPS Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical Design Stator Windings Insulation Mechanical Data Temperature Rise (sine wave) Section 1 Part 2 Section Page 10 1 of 25 Part 204/08 Page 8 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZEESDX Severe Duty – TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Severe Duty / IEEE 841 (2001) - TEFC NEMA Premium 1-400 140-S440 60 Hertz 3 - Phase 460 Service Factor (sine wave) Electrical Design Stator Windings Insulation Warranty Frame End Shields 1.15 NEMA design B (except as noted) Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 5 Years Cast Iron Cast Iron Conduit Box Cast Iron Lead Seal Gasket Fan Cover Neoprene Cast Iron Cooling Fan Rotor Shaft Bearing Type 140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze Die Cast Aluminum High Strength Carbon Steel (C1045) Single Shielded Bearing Inner Cap Shaft Seal / Slinger Stationary Bearing Caps Inpro/Seal® Bearing Isolator DE & ODE Lubrication Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Pressure Relief T-Drain Hardware Lifting Eyebolt Zinc Plated 140-440 Included Nameplate Paint Stainless Steel - Embossed Epoxy Enamel - RAL 7030 Grey Vibration 0.06 IPS Mechanical Data Temperature Rise (sine wave) Section 1 Part 2 Section Page 11 1 of 25 Part 204/08 Page 9 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data HSRGZVESD Vertical Hollow Shaft, High Trust – TEFC Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Severe Duty - TEFC High High 25-250 284TP-449TP 60 Hertz 3 - Phase 230/460 460 only 100HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 284-449TP Bi-directional, Polypropylene Steel Die Cast Aluminum Hollow - High Strength Carbon Steel (C1045) 284-449TP open ball bearing Bearing Type (ODE) 284-449TP angular contact thrust bearing Bearing Inner Cap Shaft Seal / Slinger Stationary Bearing Caps 284-449TP V-Ring Slinger Lubrication Lube Inlet Fittings Polyurea Alemite Plug T-Drain Zinc Plated 284-449TP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Mechanical Data Lead Seal Gasket Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Section 1 Part 2 Section Page 12 1 of 25 Part 204/08 Page 10 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZVESD Vertical Solid Shaft, Normal Trust – TEFC Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Bearing Type (ODE) Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Severe Duty - TEFC High Normal 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 143-256HP open ball bearing 284-365HP single shielded ball bearing 404-405HP double shielded ball bearing 444-449HP open ball bearing 143-365HP open ball bearing 404-405HP double shielded ball bearing 444-449HP single shielded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Section 1 Part 2 Section Page 13 1 of 25 Part 204/08 Page 11 / 23 Date 05 / 07 Application Manual for NEMA Motors Section 1 Part 2 Section Page 14 1 of 25 Part 204/08 Page 12 / 23 Date 05 / 07 Application Manual for NEMA Motors Electrical Data RGZZVESD Vertical Solid Shaft, Normal Trust – TEFC P-Base – Hazardous Duty Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Bearing Type (ODE) Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Hazardous Duty - TEFC High Normal 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.0 NEMA design B Copper - Random Wound Class F Class B @ 1.0SF 3 Years Cast Iron Cast Iron Oversized Cast Iron None Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 143-256HP open ball bearing 284-365HP single shielded ball bearing 404-405HP double shielded ball bearing 444-449HP open ball bearing 143-365HP open ball bearing 404-405HP double shielded ball bearing 444-449HP single shielded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449HP only) Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZVMTESD Vertical Solid Shaft, Medium Trust – TEFC P-Base Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Bearing Type (ODE) Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Severe Duty - TEFC High Medium 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 143-256HP open ball bearingbearing 284-365HP double shielded ball bearing 404-449HP angular contact thrust bearing 143-256HP angular contact thrust bearing 284-365HP angular contact thrust bearing and four-point ball bearing 404-449HP double shielded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Section 1 Part 2 Section Page 15 1 of 25 Part 204/08 Page 13 / 23 Date 05 / 07 Application Manual for NEMA Motors Section 1 Part 2 Section Page 16 1 of 25 Part 204/08 Page 14 / 23 Date 05 / 07 Application Manual for NEMA Motors Electrical Data RGZZVMTESD Vertical Solid Shaft, Medium Trust – TEFC P-Base – Hazardous Duty Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Bearing Type (ODE) Bearing Inner Cap Shaft Seal / Slinger Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Hazardous Duty - TEFC High Medium 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.0 NEMA design B Copper - Random Wound Class F Class B @ 1.0SF 3 Years Cast Iron Cast Iron Oversized Cast Iron None Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 182-256LP open ball bearing 284-449LP double shielded ball bearing 143-256HP angular contact thrust bearing 284-365HP angular contact thrust bearing and four-point ball bearing 404-449HP double shielded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449HP only) Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Application Manual for NEMA Motors Application Manual for NEMA Motors Electrical Data RGZVILESD Vertical Solid Shaft, In-Line Trust – TEFC P-Base Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Severe Duty - TEFC High In-Line 3-250 182LP-449LP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 182-449LP Bi-directional, Polypropylene Cast Iron Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 182-256LP open ball bearing 284-449LP double shielded ball bearing Bearing Type (ODE) 182-449LP duplex angular contact thrust bearing Bearing Inner Cap Shaft Seal / Slinger Stationary Bearing Caps 182-256LP Shaft Seal 284-365LP None 404-449LP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 182-449LP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Section 1 Part 2 Section Page 17 1 of 25 Part 204/08 Page 15 / 23 Date 05 / 07 Application Manual for NEMA Motors Section 1 Part 2 Section Page 18 1 of 25 Part 204/08 Page 16 / 23 Date 05 / 07 Application Manual for NEMA Motors Electrical Data RGZZVILESD Vertical Solid Shaft, In-Line Trust – TEFC P-Base – Hazardous Duty Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage Service Factor (sine wave) Electrical design Stator Windings Insulation Temperature Rise (sine wave) Warranty Frame End Shields Conduit Box Lead Seal Gasket Mechanical Data Fan Cover Cooling Fan Drip cover Rotor Shaft Bearing Type (DE) Hazardous Duty - TEFC High In-Line 3-250 182LP-449LP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.0 NEMA design B Copper - Random Wound Class F Class B @ 1.0SF 3 Years Cast Iron Cast Iron Oversized Cast Iron None Cast Iron 182-449LP Bi-directional, Polypropylene Cast Iron Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) Bearing Type (ODE) 182-449LP duplex angular contact thrust bearing Bearing Inner Cap Shaft Seal / Slinger Stationary Bearing Caps 182-256LP Shaft Seal 284-365LP None 404-449LP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449LP only) Zinc Plated 182-449LP Included Stainless Steel - engraved Epoxy Enamel - RAL 7030 Grey 0.08 IPS Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data GP10A General Purpose - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage General Purpose - TEFC High 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast aluminum with bolted feet Cast aluminum Conduit Box Cast aluminum Lead Seal Gasket Fan Cover Neoprene (o-rings) Plastic Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast aluminum High strength carbon steel (C1045) Lubricated for life Non-regreasable No V-ring slinger - DE only Lubrication Polyurea Lube Inlet Fittings NA Lube Relief Fittings Condensation Drain NA Drain holes - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Aluminum - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.15 IPS Section 1 Part 2 Section Page 19 1 of 25 Part 204/08 Page 17 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data GP10 General Purpose - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage General Purpose - TEFC High 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast iron Cast iron Conduit Box Cast aluminum Lead Seal Gasket Fan Cover Neoprene Plastic Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast aluminum High strength carbon steel (C1045) Lubricated for life Non-regreasable No V-ring slinger - DE only Lubrication Polyurea Lube Inlet Fittings NA Lube Relief Fittings Condensation Drain NA Drain holes - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Aluminum - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.15 IPS Section 1 Part 2 Section Page 20 1 of 25 Part 204/08 Page 18 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data SD10 Severe Duty - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Severe Duty - TEFC High 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.05F, Class F @ 1.15SF 3 Years Cast iron Cast iron Conduit Box Cast iron Lead Seal Gasket Fan Cover Neoprene Cast iron Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast aluminum High strength carbon steel (C1045) Double Shielded Regreasable inlet & outlet Cast iron V-ring slinger - DE and ODE Lubrication Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T - drains - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Stainless steel - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.08 IPS (2, 4, 6 pole) 0.06 IPS (8 pole) Section 1 Part 2 Section Page 21 1 of 25 Part 204/08 Page 19 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data GP100A General Purpose - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage General Purpose - TEFC Exceeds NEMA Premium 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast aluminum with bolted feet Cast aluminum Conduit Box Cast aluminum Lead Seal Gasket Fan Cover Neoprene (o-ring) Plastic Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast copper High strength carbon steel (C1045) Lubricated for life Non-regreasable No V-ring slinger - DE only Lubrication Polyurea Lube Inlet Fittings NA Lube Relief Fittings Condensation Drain NA Drain holes - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Aluminum - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.15 IPS Section 1 Part 2 Section Page 22 1 of 25 Part 204/08 Page 20 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data GP100 General Purpose - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage General Purpose - TEFC Exceeds NEMA Premium 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 18 Months Cast iron Cast iron Conduit Box Cast aluminum Lead Seal Gasket Fan Cover Neoprene Plastic Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast copper High strength carbon steel (C1045) Lubricated for life Non-regreasable No V-ring slinger - DE only Lubrication Polyurea Lube Inlet Fittings NA Lube Relief Fittings Condensation Drain NA Drain holes - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Aluminum - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.15 IPS Section 1 Part 2 Section Page 23 1 of 25 Part 204/08 Page 21 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data SD100 Severe Duty - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Severe Duty - TEFC Exceeds NEMA Premium 1-20 143T-256T 60 Hertz 3 - Phase 208-230/460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Class F, meets NEMA MG1-2003, Part 31 Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast iron Cast iron Conduit Box Cast iron Lead Seal Gasket Fan Cover Neoprene Cast iron Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast copper High strength carbon steel (C1045) Double Shielded Regreasable inlet & outlet Cast iron V-ring slinger - DE and ODE Lubrication Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Plug T-drains - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Stainless steel - engraved Epoxy enamel - RAL 7030 Grey Vibration 0.08 IPS Section 1 Part 2 Section Page 24 1 of 25 Part 204/08 Page 22 / 23 Date 05 / 07 Application Manual for NEMA Motors Application Manual for NEMA Motors Mechanical Data Electrical Data SD100 IEEE841 Severe Duty / IEEE841 (2001) - TEFC Enclosure Efficiency HP Range Frame Size Frequency Power Voltage Severe Duty / IEEE 841 (2001) - TEFC Exceeds NEMA Premium 1-20 143T-256T 60 Hertz 3 - Phase 460 & 575 Service Factor (sine wave) Electrical Design Stator Windings Insulation 1.15 NEMA design B Copper - random wound Temperature Rise (sine wave) Warranty Frame End Shields Class B @ 1.0SF, Class F @ 1.15SF 5 Years Cast iron Cast iron Conduit Box Cast iron Lead Seal Gasket Fan Cover Neoprene Cast iron Cooling Fan Bi-directional - polypropylene Rotor Shaft Bearing Type Bearing Inner Cap Shaft Seal / Slinger Die cast copper, Alum. for 8 pole motors High strength carbon steel (C1045) Single Shielded Regreasable inlet & outlet Cast iron Inpro/Seal® Bearing Isolator DE & ODE Lubrication Polyurea Lube Inlet Fittings Alemite Lube Relief Fittings Condensation Drain Pressure relief T-drains - lowest point (2) Hardware Lifting Eyebolt Zinc plated Motors > 75 lbs Nameplate Paint Stainless steel - embossed Epoxy enamel - RAL 7030 Grey Vibration 0.06 IPS Section 1 Part 2 Section Page 25 1 of 25 Part 204/08 Page 23 / 23 Date 05 / 07