NCV8570B D

NCV8570B
200 mA, Ultra Low Noise,
High PSRR, LDO, Linear
Voltage Regulator
The NCV8570B is a 200 mA Low Dropout, Linear Voltage
Regulator with ultra low noise characteristics. It’s low noise combined
with high Power Supply Rejection Ratio (PSRR) make it especially
suited for use in RF, audio or imaging applications. The device is
manufactured in an advanced BiCMOS process to provide a powerful
combination of low noise and excellent dynamic performance but with
very low ground current consumption at full loads.
The NCV8570B is stable with small, low value capacitors allowing
designers to minimise the total PCB space occupied by the solution.
The device is packaged in a small 2x2.2mm DFN6 package as well as
in a TSOP-5 package.
Features











Ultra Low Noise (typ. 10 mVrms @ VOUT = 1.8 V)
Very High PSRR (typ. 82 dB @ 1 kHz)
Excellent Line and Load Regulation
Stable with Ceramic Output Capacitors as low as 1 mF
Very Low Ground Current (typ. 75 mA @ IOUT = 200 mA)
Low Sleep Mode Current (max. 1 mA)
Active Discharge Circuit
Current Limit and Thermal Shutdown Protection
Output Voltage Options:
 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V
 Contact Factory for Other Voltage Options
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
Applications





1
CIN
1 mF
ON
OFF
IN
OUT
NCV8570B
EN
BYP
GND
2, 5, EPAD
TSOP−5
SN SUFFIX
CASE 483
PIN CONNECTIONS
EN
1
6 BYP
GND
2
5 GND
IN
3
4 OUT
DFN6
(Top View)
1
5
OUT
IN
GND
EN
BYP
TSOP−5
(Top View)
MARKING DIAGRAMS
1
XX MG
G
5
XXXAYWG
G
1
DFN6 2x2.2
3
DFN6
MN SUFFIX
CASE 506BA
XX = Specific Device Code
M = Date Code
G
= Pb−Free Package*
(*Note: Microdot may be in either location)
Satellite and HD Radio
Portable/Built−in DVD Entertainment Systems
Noise Sensitive Applications (RF, Video, Audio)
GPS Systems
Camera for Lane Change Detection and Reverse View
VIN
http://onsemi.com
VOUT
4
6
COUT
1 mF
Cnoise
10 nF
XXX = Specific Device Code
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package*
(*Note: Microdot may be in either location)
ORDERING INFORMATION
Figure 1. NCV8570B Typical Application Schematic
 Semiconductor Components Industries, LLC, 2013
June, 2013 − Rev. 3
1
See detailed ordering, marking and shipping information in the
package dimensions section on page 18 of this data sheet.
Publication Order Number:
NCV8570B/D
NCV8570B
RDIS
RPD
Figure 2. Simplified Block Diagram
PIN FUNCTION DESCRIPTION
Pin No.
DFN6
Pin No.
TSOP−5
Pin Name
1
3
EN
2, 5, EPAD
2
GND
3
1
IN
4
5
OUT
Regulated Output Voltage
6
4
BYP
Noise reduction pin. (Connect 10 nF or 100 nF capacitor to GND)
Description
Enable pin: This pin allows on/off control of the regulator. To disable the device, connect to
GND. If this function is not in use, connect to Vin. Internal 5 MW Pull Down resistor is
connected between EN and GND.
Power Supply Ground (Pins are fused for the DFN6 package). Pins 2, 5 and EPAD are
connected together through the lead frame in the DFN6 package.
Power Supply Input Voltage
MAXIMUM RATINGS
Symbol
Value
Unit
Input Voltage (Note 2)
Rating
IN
−0.3 V to 6 V
V
Chip Enable Voltage
EN
−0.3 V to VIN +0.3 V
Noise Reduction Voltage
BYP
−0.3 V to VIN +0.3 V
V
Output Voltage
OUT
−0.3 V to VIN +0.3 V
V
Output Short−Circuit Duration
Infinity
Maximum Junction Temperature
Storage Temperature Range
TJ(max)
125
C
TSTG
−55 to 150
C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may
affect device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V tested per MIL−STD−883, Method 3015
Machine Model Method 200 V
This device meets or exceeds AEC−Q100 standard.
THERMAL CHARACTERISTICS
Rating
Symbol
Value
Package Thermal Resistance, DFN6: (Notes 2, 3)
Junction−to−Case (Pin 2)
Junction−to−Ambient
YJL2
RqJA
38
110
Package Thermal Resistance, TSOP−5: (Notes 2, 3)
Junction−to−Case (Pin 2)
Junction−to−Ambient
YJL2
RqJA
92
204
2. Refer to APPLICATION INFORMATION for Safe Operating Area
3. Single component mounted on 1 oz, FR4 PCB with 645mm2 Cu area.
http://onsemi.com
2
Unit
C/W
C/W
NCV8570B
ELECTRICAL CHARACTERISTICS
(VIN = VOUT + 0.5 V or 2.5 V (whichever is greater), VEN = 1.2 V, CIN = COUT = 1 mF, Cnoise = 10 nF, IOUT = 1 mA, TJ = −40C to 125C,
unless otherwise specified) (Note 4)
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
VIN
2.5
−
5.5
V
VOUT
1.755
2.4375
2.730
2.925
3.2175
(−2.5%)
−
−
−
−
−
1.845
2.5625
2.870
3.075
3.3825
(+2.5%)
V
PSRR
−
−
−
80
82
63
−
−
−
dB
REGULATOR OUTPUT
Input Voltage Range
Output Voltage
1.8 V VIN = (VOUT + 0.5 V) to 5.5 V
2.5 V IOUT = 1 mA to 200 mA
2.8 V
3.0 V
3.3 V
Power Supply Ripple Rejection
VIN = VOUT +1.0 V,
IOUT = 1 mA to 150 mA
f = 120 Hz
f = 1 kHz
f = 10 kHz
Line Regulation
VIN = (VOUT +0.5 V) to 5.5 V, IOUT = 1 mA
DVOUT / DVIN
−0.1
−
0.1
%/V
Load Regulation
IOUT = 1 mA to 200 mA
DVOUT / DIOUT
−
0.2
5.0
mV
Output Noise Voltage
VOUT = 1.8 V,
Cnoise = 100 nF
f = 10 Hz to 100 kHz,
Cnoise = 10 nF
IOUT = 1 mA to 150 mA
VN
−
−
10
15
−
−
mVRMS
Output Current Limit
VOUT = VOUT(NOM) – 0.1 V
ILIM
200
310
470
mA
Output Short Circuit Current
VOUT = 0V
ISC
205
320
490
mA
Dropout Voltage (Note 5)
IOUT= 150 mA
VOUT(NOM) = 2.5 V
VOUT(NOM) = 2.8 V
VOUT(NOM) = 3.0 V
VOUT(NOM) = 3.3 V
VDO
−
−
−
−
100
90
85
80
180
165
150
145
mV
Dropout Voltage (Note 5)
IOUT= 200 mA
VOUT(NOM) = 2.5 V
VOUT(NOM) = 2.8 V
VOUT(NOM) = 3.0 V
VOUT(NOM) = 3.3 V
VDO
−
−
−
−
140
120
115
110
230
205
190
185
mV
IGND
−
−
70
75
110
130
mA
GENERAL
Ground Current
IOUT = 1 mA
IOUT = 200 mA
Disable Current
VEN = 0 V
IDIS
−
0.1
1.0
mA
Thermal Shutdown
Shutdown, Temperature Increasing
TSDU
−
150
−
C
Reset, Temperature Decreasing
TSDD
−
135
−
C
Vth(EN)
−
1.2
−
−
0.4
−
V
RPD(EN)
2.5
5.0
10
MW
OUTPUT ENABLE
Enable Threshold
Low
High
Internal Pull−Down Resistance
(Note 6)
TIMING
Turn−On Time
IOUT = 10 mA, VOUT =
0.975 VOUT(NOM)
Cnoise = 10 nF
Cnoise = 100 nF
tON
−
−
0.4
4.0
−
−
ms
Turn−Off Time
Cnoise = 10nF/100nF,
VOUT = 0.1 VOUT(NOM)
IOUT = 1 mA
IOUT = 10 mA
tOFF
−
−
2.0
0.6
−
−
ms
4. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25C. Low
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
5. Measured when the output voltage falls 100 mV below the nominal output voltage (nominal output voltage is the voltage at the output measured under the condition VIN = VOUT + 0.5 V). In the case of devices having the nominal output voltage VOUT = 1.8 V the minimum input
to output voltage differential is given by the VIN(MIN) = 2.5 V.
6. Expected to disable the device when EN pin is floating.
http://onsemi.com
3
NCV8570B
TYPICAL CHARACTERISTICS
Vout, OUTPUT VOLTAGE (V)
1.836
1.824
1.812
1.800
1.788
VIN = 2.5 V,
CIN = COUT = 1 mF,
Cnoise = 10 nF
1.776
1.764
−40
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (C)
Figure 3. Output Voltage vs. Junction
Temperature, VOUT = 1.8 V
Vout, OUTPUT VOLTAGE (V)
2.8560
2.8373
2.8187
2.8000
2.7813
VIN = 3.3 V,
CIN = COUT = 1 mF,
Cnoise = 10 nF
2.7627
2.7440
−40
−20
0
20
40
60
80
100
120
TJ, JUNCTION TEMPERATURE (C)
Figure 4. Output Voltage vs. Junction
Temperature, VOUT = 2.8 V
Vout, OUTPUT VOLTAGE (V)
3.06
3.04
3.02
3.00
2.98
VIN = 3.5 V,
CIN = COUT = 1 mF,
Cnoise = 10 nF
2.96
2.94
−40
−20
0
20
40
60
80
TJ, JUNCTION TEMPERATURE (C)
100
Figure 5. Output Voltage vs. Junction
Temperature, VOUT = 3.0 V
http://onsemi.com
4
120
NCV8570B
TYPICAL CHARACTERISTICS
180
VDO, DROPOUT VOLTAGE (mV)
Vout, OUTPUT VOLTAGE (V)
3.3660
3.3440
3.3220
3.3000
3.2780
VIN = 3.8 V,
CIN = COUT = 1 mF,
Cnoise = 10 nF
3.2560
3.2340
−40
−20
0
20
40
60
80
100
CIN = COUT = 1 mF,
Cnoise = 10 nF
150
TJ = 25C
120
TJ = 125C
90
60
TJ = −40C
30
0
0
120
40
TJ, JUNCTION TEMPERATURE (C)
90
180
CIN = COUT = 1 mF,
Cnoise = 10 nF
120
TJ = 25C
TJ = 125C
60
TJ = −40C
30
0
0
40
80
120
160
160
200
Figure 7. Dropout Voltage vs. Output Current,
VOUT = 2.8 V
VDO, DROPOUT VOLTAGE (mV)
VDO, DROPOUT VOLTAGE (mV)
150
120
IOUT, OUTPUT CURRENT (mA)
Figure 6. Output Voltage vs. Junction
Temperature, VOUT = 3.3 V
180
80
200
150
CIN = COUT = 1 mF,
Cnoise = 10 nF
120
TJ = 25C
90
TJ = 125C
60
TJ = −40C
30
0
0
40
80
120
160
200
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 8. Dropout Voltage vs. Output Current,
VOUT = 3.0 V
Figure 9. Dropout Voltage vs. Output Current,
VOUT = 3.3 V
http://onsemi.com
5
NCV8570B
TYPICAL CHARACTERISTICS
100
110
90
90
80
80
IOUT = 150 mA
60
PSRR (dB)
PSRR (dB)
70
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 10 nF,
COUT = 1 mF,
VOUT = 1.8 V,
VIN = 3.0 VDC  50 mVAC
30
20
10
0
IOUT = 10 mA
100
IOUT = 10 mA
10
100
IOUT = 150 mA
70
60
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 100 nF,
20 COUT = 1 mF,
10 VOUT = 1.8 V,
VIN = 3.0 VDC  50 mVAC
0
10
100
1k
10k
FREQUENCY (Hz)
30
1k
10k
FREQUENCY (Hz)
100k
1M
Figure 10. PSRR vs. Frequency, 1.8 V Output
Voltage Option, COUT = 1 mF, Cnoise = 10 nF
120
110
IOUT = 10 mA
90
90
80
70
IOUT = 150 mA
60
PSRR (dB)
PSRR (dB)
IOUT = 10 mA
100
80
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 10 nF,
COUT = 4.7 mF,
VOUT = 1.8 V,
VIN = 3.0 VDC  50 mVAC
30
20
10
10
100
IOUT = 150 mA
70
60
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 100 nF,
20 COUT = 4.7 mF,
10 VOUT = 1.8 V,
VIN = 3.0 VDC  50 mVAC
0
10
100
1k
10k
FREQUENCY (Hz)
30
1k
10k
FREQUENCY (Hz)
100k
1M
Figure 12. PSRR vs. Frequency, 1.8 V Output
Voltage Option, COUT = 4.7 mF, Cnoise = 10 nF
110
100
90
70
60
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 10 nF,
COUT = 1 mF,
VOUT = 2.8 V,
VIN = 3.3 VDC  50 mVAC
30
20
10
10
100
1k
IOUT = 150 mA
80
IOUT = 150 mA
PSRR (dB)
PSRR (dB)
80
70
IOUT = 200 mA
60
50
40
TA = 25C,
Cnoise = 100 nF,
COUT = 1 mF,
VOUT = 2.8 V,
VIN = 3.3 VDC  50 mVAC
30
20
10
10k
100k
1M
IOUT = 10 mA
100
IOUT = 10 mA
90
100k
Figure 13. PSRR vs. Frequency, 1.8V Output
Voltage Option, COUT = 4.7mF, Cnoise = 100nF
110
0
1M
Figure 11. PSRR vs. Frequency, 1.8 V Output
Voltage Option, COUT = 1mF, Cnoise = 100nF
100
0
100k
0
1M
FREQUENCY (Hz)
10
1k
10k
FREQUENCY (Hz)
Figure 14. PSRR vs. Frequency, 2.8 V Output
Voltage Option, COUT = 1 mF, Cnoise = 10 nF
Figure 15. PSRR vs. Frequency, 2.8 V Output
Voltage Option, COUT = 1 mF, Cnoise = 100 nF
http://onsemi.com
6
100
100k
1M
NCV8570B
TYPICAL CHARACTERISTICS
110
110
100
100
IOUT = 10 mA
90
90
80
70
60
IOUT = 200 mA
50
40
30
20
10
0
10
OUTPUT VOLTAGE NOISE (mV/HZ)
TA = 25C,
Cnoise = 10 nF,
COUT = 4.7 mF,
VOUT = 2.8 V,
VIN = 3.3 VDC  50 mVAC
100
1k
IOUT = 200 mA
50
40
TA = 25C,
Cnoise = 100 nF,
COUT = 4.7 mF,
VOUT = 2.8 V,
VIN = 3.3 VDC  50 mVAC
10
10k
100k
0
1M
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 16. PSRR vs. Frequency, 2.8 V Output
Voltage Option, COUT = 4.7 mF, Cnoise = 10 nF
Figure 17. PSRR vs. Frequency, 2.8 V Output
Voltage Option, COUT = 4.7 mF, Cnoise = 100 nF
10
VOUT = 2.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 22.6 mVrms
1.0
0.01
10
60
20
VOUT = 3.3 V
10 Hz − 100 kHz Integral
Noise: Vn = 25.3 mVrms
0.10
IOUT = 150 mA
70
30
OUTPUT VOLTAGE NOISE (mV/HZ)
OUTPUT VOLTAGE NOISE (mV/HZ)
10
1.0
PSRR (dB)
IOUT = 150 mA
IOUT = 50 mA,
COUT = 1 mF,
Cnoise = 10 nF
VIN = VOUT = +0.5 V or
2.5 V, whichever is higher
100
1k
VOUT = 1.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 14.9 mVrms
10k
100k
1M
VOUT = 3.3 V
10 Hz − 100 kHz Integral
Noise: Vn = 11.9 mVrms
1.0
IOUT = 50 mA,
COUT = 1 mF,
Cnoise = 100 nF
VIN = VOUT = +0.5 V or
2.5 V, whichever is higher
VOUT = 2.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 11.7 mVrms
0.10
0.01
VOUT = 1.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 9.4 mVrms
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 18. Output Noise vs. Frequency, COUT =
1 mF, Cnoise = 10 nF, IOUT = 50 mA
Figure 19. Output Noise vs. Frequency, COUT =
1 mF, Cnoise = 100 nF, IOUT = 50 mA
10
VOUT = 3.3 V
10 Hz − 100 kHz Integral
Noise: Vn = 22.85 mVrms
OUTPUT VOLTAGE NOISE (mV/HZ)
PSRR (dB)
80
10
IOUT = 10 mA
VOUT = 2.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 22.7 mVrms
VOUT = 1.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 15 mVrms
0.10 I
OUT = 200 mA,
COUT = 1 mF,
Cnoise = 10 nF
VIN = VOUT = +0.5 V or
2.5 V, whichever is higher
0.01
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
VOUT = 3.3 V
10 Hz − 100 kHz Integral
Noise: Vn = 12 mVrms
1.0
VOUT = 2.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 11.7 mVrms
0.10
0.01
IOUT = 200 mA,
COUT = 1 mF,
Cnoise = 100 nF
VIN = VOUT = +0.5 V or
2.5 V, whichever is higher
VOUT = 1.8 V
10 Hz − 100 kHz Integral
Noise: Vn = 9.5 mVrms
10
Figure 20. Output Noise vs. Frequency, COUT =
1 mF, Cnoise = 10 nF, IOUT = 200 mA
100
1k
10k
FREQUENCY (Hz)
100k
1M
Figure 21. Output Noise vs. Frequency, COUT =
1 mF, Cnoise = 100 nF, IOUT = 200 mA
http://onsemi.com
7
NCV8570B
TYPICAL CHARACTERISTICS
TA = 25C,
COUT = 1 mF,
VOUT = 3.3 V,
IOUT = 200 mA
VIN = 3.8 V
30
25
20
15
10
0
50
18
16
14
12
10
8
4
2
0
100 150 200 250 300 350 400 450 500
Cnoise, NOISE BYPASS CAPACITOR (nF)
TA = 25C,
Cnoise = 100 nF,
VOUT = 3.3 V,
IOUT = 200 mA
VIN = 3.8 V
6
1
Figure 22. Output Noise vs. Noise Bypass
Capacitance, COUT = 1 mF, VOUT = 3.3 V, IOUT =
200 mA
19
21
15
26
VOUT = 3.3 V
24
VOUT = 2.8 V
10 HZ to 100 kHz RMS OUTPUT
NOISE (mVrms)
28
22
20
18
16
VOUT = 1.8 V
14
TA = 25C, Cnoise = 10 nF, COUT = 1 mF,
VIN = VOUT + 0.5 V or 2.5 V, whichever is higher
12
0
25
50
75
100
125
150
IOUT, OUTPUT CURRENT (mA)
175
14
13
VOUT = 2.8 V
11
10
9
VOUT = 1.8 V
8
7
TA = 25C, Cnoise = 100 nF, COUT = 1 mF,
VIN = VOUT + 0.5 V or 2.5 V, whichever is higher
6
5
200
VOUT = 3.3 V
12
0
Figure 24. Output Noise vs. Load Current,
Cnoise = 10 nF, COUT = 1 mF
25
50
75
100
125
150
IOUT, OUTPUT CURRENT (mA)
200
200 mA
1 mA
100
0
1.85
1.80
1.75
1.70
COUT = 4.7 mF, VIN = 2.5 V, Cnoise = 100 nF,
dIOUT/dt = 200 mA / 1 ms
1.65
1.60
0
40
80
175
Figure 25. Output Noise vs. Load Current,
Cnoise = 100 nF, COUT = 1 mF
300
VOUT, OUTPUT VOLTAGE (V)
10 HZ to 100 kHz RMS OUTPUT
NOISE (mVrms)
5
7
9
11 13 15 17
COUT, OUTPUT CAPACITOR (mF)
Figure 23. Output Noise vs. Output
Capacitance, Cnoise = 100 nF, VOUT = 3.3 V,
IOUT = 200 mA
30
10
3
120 160 200 240 280 320 360 400
t, TIME (ms)
Figure 26. Load Transient Response, VOUT =
1.8 V, COUT = 4.7 mF, Cnoise = 100 nF
http://onsemi.com
8
IOUT, OUTPUT CURRENT (mA)
5
20
10 HZ to 100 kHz RMS OUTPUT
NOISE (mVrms)
10 HZ to 100 kHz RMS OUTPUT
NOISE (mVrms)
35
200
NCV8570B
TYPICAL CHARACTERISTICS
VOUT, OUTPUT VOLTAGE (V)
200
200 mA
1 mA
100
0
1.90
1.85
1.80
1.75
1.70
COUT = 1 mF, VIN = 2.5 V, Cnoise = 100 nF,
dIOUT/dt = 200 mA / 1 ms
1.65
1.60
0
40
80
IOUT, OUTPUT CURRENT (mA)
300
120 160 200 240 280 320 360 400
t, TIME (ms)
Figure 27. Load Transient Response, VOUT =
1.8 V, COUT = 1 mF, Cnoise = 100 nF
VOUT, OUTPUT VOLTAGE (V)
200
200 mA
1 mA
100
0
3.40
3.35
3.30
3.25
3.20
COUT = 4.7 mF, VIN = 3.8 V, Cnoise = 100 nF,
dIOUT/dt = 200 mA / 1 ms
3.15
3.10
0
40
80
IOUT, OUTPUT CURRENT (mA)
300
120 160 200 240 280 320 360 400
t, TIME (ms)
Figure 28. Load Transient Response, VOUT =
3.3 V, COUT = 4.7 mF, Cnoise = 100 nF
VOUT, OUTPUT VOLTAGE (V)
200
200 mA
1 mA
100
0
3.40
3.35
3.30
3.25
3.20
COUT = 1 mF, VIN = 3.8 V, Cnoise = 100 nF,
dIOUT/dt = 200 mA / 1 ms
3.15
3.10
0
40
80
120 160 200 240 280 320 360 400
t, TIME (ms)
Figure 29. Load Transient Response, VOUT =
3.3 V, COUT = 1 mF, Cnoise = 100 nF
http://onsemi.com
9
IOUT, OUTPUT CURRENT (mA)
300
NCV8570B
TYPICAL CHARACTERISTICS
3.5
VIN = 3.5 V
VIN = 2.5 V
3.0
2.5
1.810
1.805
1.800
1.795
1.790
COUT = 1 mF, VIN = 2.5 V, Cnoise = 100 nF,
IOUT = 30 mA, dVIN/dt = 1 V / 1 ms
1.785
1.780
VIN, INPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
4.0
0
20
40
60
80 100 120 140 160 180 200
t, TIME (ms)
Figure 30. Line Transient Response,
VOUT = 1.8 V, COUT = 1 mF, IOUT = 30 mA
3.5
VIN = 3.5 V
VIN = 2.5 V
3.0
2.5
1.810
1.805
1.800
1.795
COUT = 1 mF, VIN = 2.5 V,
Cnoise = 100 nF, IOUT = 200 mA,
dVIN/dt = 1 V / 1 ms
1.790
1.785
1.780
0
20
40
60
VIN, INPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
4.0
80 100 120 140 160 180 200
t, TIME (ms)
Figure 31. Line Transient Response,
VOUT = 1.8 V, COUT = 1 mF, IOUT = 200 mA
5.0
VIN = 3.5 V
4.0
3.5
3.010
3.005
3.000
2.995
2.990
COUT = 1 mF, VIN = 3.5 V,
Cnoise = 100 nF, IOUT = 30 mA,
dVIN/dt = 1 V / 1 ms
2.985
2.980
0
20
40
60
80 100 120 140 160 180 200
t, TIME (ms)
Figure 32. Line Transient Response,
VOUT = 3.0 V, COUT = 1 mF, IOUT = 30 mA
http://onsemi.com
10
VIN, INPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
4.5
VIN = 4.5 V
NCV8570B
TYPICAL CHARACTERISTICS
4.5
VIN = 4.5 V
4.0
VIN = 3.5 V
3.5
3.010
3.005
3.000
2.995
COUT = 1 mF, VIN = 3.5 V,
Cnoise = 100 nF, IOUT = 200 mA,
dVIN/dt = 1 V / 1 ms
2.990
2.985
2.980
0
20
40
60
VIN, INPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
5.0
80 100 120 140 160 180 200
t, TIME (ms)
Figure 33. Line Transient Response,
VOUT = 3.0 V, COUT = 1 mF, IOUT = 200 mA
3.8
VEN = 3.8 V
1.9
0.0
VEN = 0 V
Cnoise = 10 nF
4.0
3.0
Cnoise = 220 nF
2.0
1.0
Cnoise = 100 nF
COUT = 1 mF,
VIN = 3.8 V
0.0
−1.0
VEN, ENABLE VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
5.7
Cnoise = 47 nF
0
2
4
6
8
10
t, TIME (ms)
12
14
16
Figure 34. Turn−On Response
VOUT = 3.3 V, COUT = 1 mF, IOUT = 30 mA
3.50
VEN = 3.5 V
1.75
0.00
VEN = 0 V
Cnoise = 10 nF
4.0
3.0
Cnoise = 220 nF
2.0
1.0
Cnoise = 100 nF
0.0
−1.0
Cnoise = 47 nF
0
2
4
6
8
10
t, TIME (ms)
COUT = 1 mF,
VIN = 3.5 V
12
14
Figure 35. Turn−On Response
VOUT = 3 V, COUT = 1 mF, IOUT = 30 mA
http://onsemi.com
11
16
VEN, ENABLE VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
5.25
NCV8570B
TYPICAL CHARACTERISTICS
2
VEN = 2.5 V
1
0
VEN = 0 V
Cnoise = 10 nF
2.0
1.5
Cnoise = 220 nF
1.0
0.5
Cnoise = 100 nF
0.0
−0.5
COUT = 1 mF,
VIN = 2.5 V
Cnoise = 47 nF
0
1
2
3
4
5
6
7
8
9
VEN, ENABLE VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
3
10
t, TIME (ms)
Figure 36. Turn−On Response
VOUT = 1.8 V, COUT = 1 mF, IOUT = 30 mA
5.7
Cnoise = 10 nF,
TJ = 25C
VEN = 0 V
4.0
3.8
1.9
0.0
RRLOAD = 22 W
3.0
RRLOAD = 110 W
2.0
RRLOAD = 3.3 kW
1.0
VEN, ENABLE VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
VEN = 3.8 V
0.0
−1.0
0
1
2
3
4
5
6
t, TIME (ms)
7
8
9
10
Figure 37. Turn−Off Response
VOUT = 3.3 V, COUT = 1 mF
VOUT, OUTPUT VOLTAGE (V)
5.25
3.50
1.75
VEN = 0 V
0.00
RRLOAD = 20 W
3.0
RRLOAD = 100 W
2.0
RRLOAD = 3 kW
1.0
0.0
−1.0
0
1
2
3
4
5
6
t, TIME (ms)
7
8
Figure 38. Turn−Off Response
VOUT = 3 V, COUT = 1 mF
http://onsemi.com
12
9
10
VEN, ENABLE VOLTAGE (V)
Cnoise = 10 nF,
TJ = 25C
VEN = 3.5 V
NCV8570B
TYPICAL CHARACTERISTICS
1.25
0
RRLOAD = 12 W
1.5
RRLOAD = 60 W
1.0
RRLOAD = 1.8 kW
0.5
tON, TURN−ON TIME (ms)
VEN, ENABLE VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
2.5
VEN = 0 V
2.0
12
3.75
Cnoise = 10 nF,
TJ = 25C
VEN = 2.5 V
0.0
−0.5
0
1
2
3
4
5
6
t, TIME (ms)
7
8
9
10
8
VOUT = 3.3 V
6
VOUT = 3 V
4
VOUT = 1.8 V
2
0
10
TJ = 25C,
IOUT = 0 mA − 200 mA
0
Figure 39. Turn−Off Response
VOUT = 1.8 V, COUT = 1 mF
Figure 40. Turn−On Time vs. Noise Bypass
Capacitance, COUT = 1 mF, IOUT = 0 mA −
200 mA
600
400
200
IOUT = 1 mA
4
3
VOUT = 3 V
2
1
VOUT = 0 V
0
−1
0.0
0
Short−Circuit
Normal
Operation
0.1
0.2
0.3
0.4 0.5 0.6
t, TIME (ms)
0.7
0.8
0.9
350
IOUT, OUTPUT CURRENT (mA)
ISC, SHORT−CIRCUIT CURRENT (mA)
VOUT, OUTPUT VOLTAGE (V)
800
IOUT = 1 mA
Cnoise = 100 nF
IOUT = 325 mA
VIN = VOUT + 0.5 V,
333 CIN = COUT = 1 mF,
Cnoise = 10 nF
317
300
250
−40
2.00
300
1.75
IOUT, OUTPUT CURRENT (mA)
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
400
200
100
0
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (C)
120
1.50
1.25
TJ = 25C
1.00
VOUT = 3 V
0.75
2.0
1.0
IOUT = 200 mA
Cnoise = 100 nF
0
−1.0
0.0
−20
Figure 42. Short−Circuit Current vs. Junction
Temperature, VOUT = 1.8 V, 3.3 V
Normal
Operation
3.0
VOUT = 1.8 V
267
1.0
IOUT = 200 mA
4.0
VOUT = 3.3 V
283
Figure 41. Short−Circuit Protection,
VOUT = 3 V, COUT = 1 mF, Cnoise = 100 nF
Thermal
Shutdown
20 40 60 80 100 120 140 160 180 200 220 240
Cnoise, NOISE BYPASS CAPACITANCE (nF)
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
0.50
TJ = −40C
0.25
TJ = 125C
IOUT = 10 mA
Cnoise = 100 nF
2.5
4
0.00
9.0 10.0
0
0.5
1
1.5
2
3
3.5
4.5
5
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 43. Thermal Shutdown Protection
VOUT = 3 V, Cnoise = 100 nF, COUT = 1 mF
Figure 44. Output Voltage vs. Input Voltage,
VOUT = 1.8 V, COUT = 1 mF
http://onsemi.com
13
5.5
NCV8570B
TYPICAL CHARACTERISTICS
3.50
3.25
3.00
2.75
2.50
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
3.00
2.50
2.25
2.00
1.75
1.50
1.25
1.00
TJ = 25C
0.75
TJ = −40C
0.50
0
IOUT = 10 mA
Cnoise = 100 nF
TJ = 125C
0.25
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
2.75
5.5
TJ = 25C
TJ = −40C
TJ = 125C
0
0.5
1
1.5
2
2.5
3
3.5
IOUT = 10 mA
Cnoise = 100 nF
4
4.5
5
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 45. Output Voltage vs. Input Voltage,
VOUT = 2.8 V, COUT = 1 mF
Figure 46. Output Voltage vs. Input Voltage,
VOUT = 3.3 V, COUT = 1 mF
1.8091
2.8038
VOUT, OUTPUT VOLTAGE (V)
1.8089
1.8088
1.8087
1.8086
1.8085
1.8084
1.8083
1.8082
3
3.5
4
4.5
5
5.5
2.8036
2.8035
2.8034
2.8033
2.8032
2.8031
2.8030
2.8029
2.8028
3
3.5
4
4.5
5
5.5
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 47. Output Voltage vs. Input Voltage,
VOUT = 1.8 V, COUT = 1 mF
Figure 48. Output Voltage vs. Input Voltage,
VOUT = 2.8 V, COUT = 1 mF
3.3129
90
VOUT, OUTPUT VOLTAGE (V)
3.3127
IQ, QUIESCENT CURRENT (mA)
TJ = 25C
IOUT = 10 mA
Cnoise = 100 nF
3.3128
3.3126
3.3125
3.3124
3.3123
3.3122
3.3121
3.3120
3.3119
3.5
TJ = 25C
IOUT = 10 mA
Cnoise = 100 nF
2.8037
VOUT, OUTPUT VOLTAGE (V)
TJ = 25C
IOUT = 10 mA
Cnoise = 100 nF
1.8090
1.8081
2.5
5.5
4
4.5
5
5.5
80
70
TJ = 125C
60
50
TJ = 25C
40
TJ = −40C
30
20
VOUT = 2.8 V
COUT = 1 mF
10
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 49. Output Voltage vs. Input Voltage,
VOUT = 3.3 V, COUT = 1 mF
Figure 50. Quiescent Current vs. Input
Voltage, VOUT = 2.8 V, COUT = 1 mF
http://onsemi.com
14
5.5
NCV8570B
TYPICAL CHARACTERISTICS
100
90
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
100
TJ = 25C
80
70
60
TJ = 125C
50
40
TJ = −40C
30
20
VOUT = 3.3 V
COUT = 1 mF
10
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
TJ = 25C
70
TJ = −40C
60
50
40
CIN = COUT = 1 mF,
Cnoise = 10 nF
30
20
40
60
80
100 120 140 160 180 200
VIN, INPUT VOLTAGE (V)
IOUT, OUTPUT CURRENT (mA)
Figure 51. Quiescent Current vs. Input
Voltage, VOUT = 3.3 V, COUT = 1 mF
Figure 52. Quiescent Current vs. Output
Current, VOUT = 3.3 V
90
TJ = 125C
80
TJ = 25C
70
TJ = −40C
IQ, QUIESCENT CURRENT (mA)
IQ, QUIESCENT CURRENT (mA)
80
100
60
50
40
CIN = COUT = 1 mF,
Cnoise = 10 nF
30
20
0
20
40
60
80
TJ = 125C
80
TJ = 25C
70
TJ = −40C
60
50
40
CIN = COUT = 1 mF,
Cnoise = 10 nF
30
20
40
60
80
100 120 140 160 180 200
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 53. Quiescent Current vs. Output
Current, VOUT = 3.0 V
Figure 54. Quiescent Current vs. Output
Current, VOUT = 2.8 V
COUT ESR, OUTPUT CAPACITOR (W)
100
TJ = 125C
90
80
TJ = 25C
70
TJ = −40C
60
50
40
CIN = COUT = 1 mF,
Cnoise = 10 nF
30
0
90
20
0
100 120 140 160 180 200
110
IQ, QUIESCENT CURRENT (mA)
TJ = 125C
20
0
5.5
100
20
90
20
40 60 80 100 120 140 160 180 200
IOUT, OUTPUT CURRENT (mA)
10
Unstable Operation Region
VOUT = 3.3 V
1
VOUT = 2.8 V
VOUT = 1.8 V
Stable Operation Region
0.1
VOUT = 1.8 V, 2.8 V, 3.3 V, CIN = COUT = 1 mF,
Cnoise = 10 nF, VIN = VOUT + 0.5 V or 2.5 V
whichever is higher.
0.01
0
Figure 55. Quiescent Current vs. Output
Current, VOUT = 1.8 V
0.02 0.04 0.06 0.08 0.1
0.12 0.14 0.16 0.18 0.2
IOUT, OUTPUT CURRENT (A)
Figure 56. Output Capacitor ESR vs. Output
Current
http://onsemi.com
15
NCV8570B
APPLICATIONS INFORMATION
General
internal 5 MW pull−down resistor (RPD) assures that the
device is turned off when EN pin is not connected.
The device can be used as a simple regulator without use
of the chip enable feature by tying the EN to the IN pin.
The NCV8570B is a high performance 200 mA low
dropout linear regulator. This device delivers excellent noise
and dynamic performance consuming only 75 mA (typ)
quiescent current at full load, with the PSRR of (typ) 82 dB
at 1 kHz. Excellent load transient performance and small
package size makes the device ideal for portable
applications.
Logic EN input provides ON/OFF control of the output
voltage. When the EN is low the device consumes as low as
typically 0.1 mA.
Access to the major contributor of noise within the
integrated circuit – Bandgap Reference is provided through
the BYP pin. This allows bypassing the source of noise by
the noise reduction capacitor and reaching noise levels
below 10 mVRMS.
The device is fully protected in case of output short circuit
condition and overheating assuring a very robust design.
Active Discharge
Active discharge circuitry has been implemented to insure
a fast VOUT turn off time. When EN goes low, the active
discharge transistor turns on creating a path to discharge the
output capacitor COUT through 1 kW (RDIS) resistor.
Turn−On Time
The Turn−On time of the regulator is defined as the time
needed to reach the output voltage which is 98% VOUT after
assertion of the EN pin. This time is determined by the noise
bypass capacitance Cnoise and nominal output voltage level
VOUT according the following formula:
t ON [s] + C noise [F] @
Input Capacitor Requirements (CIN)
V OUT [V]
68 @ 10 −6 [A]
(eq. 1)
Example:
Using Cnoise = 100 nF, VOUT = 3 V, COUT = 1 mF,
It is recommended to connect a 1 mF ceramic capacitor
between IN pin and GND pin of the device. This capacitor
will provide a low impedance path for unwanted AC signals
or noise present on the input voltage. The input capacitor
will also limit the influence of input trace inductances and
Power Supply resistance during sudden load current
changes. Higher capacitances will improve the line transient
response.
t ON + 100 @ 10
−9 @
3
68 @ 10 −6
+ 4.41 ms
The Turn−On time is independent of the load current and
output capacitor COUT. To avoid output voltage overshoot
during Turn−On please select Cnoise  10 nF.
Current Limit
Output Capacitor Requirements (COUT)
Output Current is internally limited within the IC to a
typical 310 mA. The NCV8570B will source this amount of
current measured with a voltage 100 mV lower than the
typical operating output voltage. If the Output Voltage is
directly shorted to ground (VOUT = 0 V), the short circuit
protection will limit the output current to 320 mA (typ). The
current limit and short circuit protection will work properly
up to VIN = 5.5 V at TA = 25C. There is no limitation for the
short circuit duration.
The NCV8570B has been designed to work with low ESR
ceramic capacitors on the output. The device will also work
with other types of capacitors until the minimum value of
capacitance is assured and the capacitor ESR is within the
specified range. Generally it is recommended to use 1 mF or
larger X5R or X7R ceramic capacitor on the output pin.
Noise Bypass Capacitor Requirements (Cnoise)
The Cnoise capacitor is connected directly to the high
impedance node. Any loading on this pin like the connection
of oscilloscope probe, or the Cnoise capacitor leakage will
cause a voltage drop in regulated output voltage. The
minimum recommended value of noise bypass capacitor is
10 nF. Values below 10 nF should be avoided due to possible
Turn−On overshoot. Particular value should be chosen
based on the output noise requirements (Figure 22). Larger
values of Cnoise will improve the output noise and PSRR but
will increase the regulator Turn−On time.
Thermal Shutdown
When the die temperature exceeds the Thermal Shutdown
threshold (TSDU − 150C typical), Thermal Shutdown event
is detected and the output (VOUT) is turned off.
The IC will remain in this state until the die temperature
decreases below the Thermal Shutdown Reset threshold
(TSDU − 135C typical). Once the IC temperature falls below
the 135C the LDO is turned−on again.
The thermal shutdown feature provides the protection
from a catastrophic device failure due to accidental
overheating. This protection is not intended to be used as a
substitute for proper heat sinking.
Enable Operation
The enable function is controlled by the logic pin EN. The
voltage threshold of this pin is set between 0.4 V and 1.2 V.
Voltage lower than 0.4 V guarantees the device is off.
Voltage higher than 1.2 V guarantees the device is on. The
NCV8570B enters a sleep mode when in the off state
drawing less than typically 0.1 mA of quiescent current. The
Reverse Current
The PMOS pass transistor has an inherent body diode
which will conduct the current in case that the VOUT > VIN.
http://onsemi.com
16
NCV8570B
100 nF from the BYP pin to ground. For more information
please refer to Figures 22 through 24.
Such condition could exist in the case of pulling the VIN
voltage to ground. Then the output capacitor voltage will be
partially discharged through the PMOS body diode. It have
been verified that the device will not be damaged if the
output capacitance is less than 22 mF. If however larger
output capacitors are used or extended reverse current
condition is anticipated the device may require additional
external protection against the excessive reverse current.
Minimum Load Current
NCV8570B does not require any minimum load current
for stability. The minimum load current is assured by the
internal circuitry.
Power Dissipation
For given ambient temperature TA and thermal resistance
RqJA the maximum device power dissipation can be
calculated by:
Output Noise
If we neglect the noise coming from the (IN) input pin of
the LDO, the main contributor of noise present on the output
pin (OUT) is the internal bandgap reference. This is because
any noise which is generated at this node will be
subsequently amplified through the error amplifier and the
PMOS pass device. Access to the bandgap reference node is
supplied through the BYP pin. For the 1.8 V output voltage
option Noise can be reduced from a typical value of
15 mVrms by using 10 nF to less than 10 mVrms by using a
270
250
230
210
0.55
220
0.40
qJA, 1 oz Cu Thickness
190
170
150
0
240
0.45
PD(MAX), TA = 25C,
1 oz Cu Thickness
qJA, 2 oz Cu Thickness
100
200
300
400
500
PCB COPPER AREA (mm2)
600
P D + ǒV IN * V OUTǓI OUT ) V INI GND
0.60
0.50
0.35
0.30
0.25
200
(eq. 2)
160
140
(eq. 3)
1.20
PD(MAX), TA = 25C,
2 oz Cu Thickness
180
1.10
1.00
0.90
PD(MAX), TA = 25C,
1 oz Cu Thickness
120
0.80
0.70
0.60
100
0.20
700
Figure 57. Thermal Resistance and Maximum
Power Dissipation vs. Copper Area (TSOP−5)
q JA
0.50
qJA, 1 oz Cu Thickness
qJA, 2 oz Cu Thickness
80
0.40
0
100
200
300
400
500
600
700
PCB COPPER AREA (mm2)
Figure 58. Thermal Resistance and Maximum
Power Dissipation vs. Copper Area (DFN6)
Load Regulation
PD(MAX), MAXIMUM POWER DISSIPATION (W)
qJA, JUNCTION−TO−AMBIENT
THERMAL RESISTANCE (C/W)
290
T J(MAX) * T A
The actual power dissipation can be calculated by the
formula:
qJA, JUNCTION−TO−AMBIENT
THERMAL RESISTANCE (C/W)
PD(MAX), TA = 25C,
2 oz Cu Thickness
PD(MAX), MAXIMUM POWER DISSIPATION (W)
310
P D(MAX) +
In the frequency range from 10 Hz up to about 10 kHz the
larger noise bypass capacitor Cnoise will help to improve the
PSRR. At the frequencies above 10 kHz the addition of
higher COUT output capacitor will result in improved PSRR.
The NCV8570B features very good load regulation of
5 mV Max. in 0 mA to 200 mA range. In order to achieve
this very good load regulation a special attention to PCB
design is necessary. The trace resistance from the OUT pin
to the point of load can easily approach 100 mW which will
cause 20 mV voltage drop at full load current, deteriorating
the excellent load regulation.
PCB Layout Recommendations
Connect the input (CIN), output (COUT) and noise bypass
capacitors (Cnoise) as close as possible to the device pins.
The Cnoise capacitor is connected to high impedance BYP
pin and thus the length of the trace between the capacitor and
the pin should be as small as possible to avoid noise pickup.
In order to minimize the solution size use 0402 or 0603
capacitors. To obtain small transient variations and good
regulation characteristics place CIN and COUT capacitors
close to the device pins and make the PCB traces wide.
Larger copper area connected to the pins will also improve
the device thermal resistance.
Line Regulation
The NCV8570B features very good line regulation of
0.6mV/V (typ). Furthermore the detailed Output Voltage vs.
Input Voltage characteristics (Figures 47 through 49) show
that up to VIN = 5 V the Output Voltage deviation is typically
less than 250 mV for 1.8 V output voltage option and less
than 150 mV for higher output voltage options. Above the
VIN = 5 V the output voltage falls rapidly which leads to the
typical 0.6 mV/V.
Power Supply Rejection Ratio
The NCV8570B features excellent Power Supply
Rejection ratio. The PSRR can be tuned by selecting proper
Cnoise and COUT capacitors.
http://onsemi.com
17
NCV8570B
ORDERING INFORMATION
Device*
Nominal Output
Voltage
Marking
NCV8570BMN180R2G
1.8 V
AK
NCV8570BMN250R2G
2.5 V
AP
NCV8570BMN280R2G
2.8 V
AL
NCV8570BMN300R2G
3.0 V
AM
NCV8570BMN330R2G
3.3 V
AN
NCV8570BSN18T1G
1.8 V
ADK
NCV8570BSN25T1G
2.5 V
ADZ
NCV8570BSN28T1G
2.8 V
ADM
NCV8570BSN30T1G
3.0 V
ADN
NCV8570BSN33T1G
3.3 V
ADP
Package
Shipping†
DFN6
2 x 2.2
(Pb−Free)
3000 / Tape & Reel
TSOP−5
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
http://onsemi.com
18
NCV8570B
PACKAGE DIMENSIONS
DFN6 2x2.2, 0.65P
CASE 506BA
ISSUE A
A
B
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.20 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L
L
L1
ÉÉÉ
ÉÉÉ
ÉÉÉ
PIN ONE
REFERENCE
2X
0.10 C
DETAIL A
E
ALTERNATE TERMINAL
CONSTRUCTIONS
TOP VIEW
2X
ÉÉ
ÉÉ
EXPOSED Cu
0.10 C
A
0.10 C
MOLD CMPD
DIM
A
A1
b
D
D2
E
E2
e
K
L
L1
ÉÉÉ
ÉÉÉ
ÇÇÇ
A3
A1
DETAIL B
DETAIL B
ALTERNATE
CONSTRUCTIONS
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20
0.30
2.00 BSC
1.10
1.30
2.20 BSC
0.70
0.90
0.65 BSC
0.20
−−−
0.25
0.35
0.00
0.10
7X
0.08 C
SIDE VIEW
C
A1
L
e
6X
3
1
1.36
PACKAGE
OUTLINE
D2
DETAIL A
6X
SOLDERING FOOTPRINT*
SEATING
PLANE
6X
0.58
L1
2.50
0.96
E2
K
6
4
BOTTOM VIEW
1
6X
b
6X
0.35
0.10 C A B
0.05 C
0.65
PITCH
DIMENSIONS: MILLIMETERS
NOTE 3
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
19
NCV8570B
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE K
D 5X
NOTE 5
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
0.20 C A B
0.10 T
M
2X
0.20 T
B
5
1
4
2
B
S
3
K
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
SIDE VIEW
C
SEATING
PLANE
END VIEW
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
20
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV8570B/D