MPC5607B Microcontroller Data Sheet - Data Sheets

Freescale Semiconductor
Data Sheet: Technical Data
Document Number: MPC5607B
Rev. 8, 04/2014
MPC5607B
100 LQFP
14 mm x 14 mm
MPC5607B Microcontroller
Data Sheet
•
•
•
•
•
•
•
•
•
•
•
•
•
Single issue, 32-bit CPU core complex (e200z0h)
— Compliant with the Power Architecture®
technology embedded category
— Enhanced instruction set allowing variable
length encoding (VLE) for code size footprint
reduction. With the optional encoding of mixed
16-bit and 32-bit instructions, it is possible to
achieve significant code size footprint
reduction.
Up to 1.5 MB on-chip code flash memory supported
with the flash memory controller
64 (4 × 16) KB on-chip data flash memory with ECC
Up to 96 KB on-chip SRAM
Memory protection unit (MPU) with 8 region
descriptors and 32-byte region granularity on certain
family members (Refer to Table 1 for details.)
Interrupt controller (INTC) capable of handling 204
selectable-priority interrupt sources
Frequency modulated phase-locked loop (FMPLL)
Crossbar switch architecture for concurrent access to
peripherals, Flash, or RAM from multiple bus
masters
16-channel eDMA controller with multiple transfer
request sources using DMA multiplexer
Boot assist module (BAM) supports internal Flash
programming via a serial link (CAN or SCI)
Timer supports I/O channels providing a range of
16-bit input capture, output compare, and pulse
width modulation functions (eMIOS)
2 analog-to-digital converters (ADC): one 10-bit and
one 12-bit
Cross Trigger Unit to enable synchronization of
ADC conversions with a timer event from the
eMIOS or PIT
© Freescale Semiconductor, Inc., 2010-2014. All rights reserved.
176 LQFP
24 mm x 24 mm
•
•
•
•
•
•
•
•
•
•
144 LQFP
20 mm x 20 mm
208 MAPBGA
17 mm x 17 mm
Up to 6 serial peripheral interface (DSPI) modules
Up to 10 serial communication interface (LINFlex)
modules
Up to 6 enhanced full CAN (FlexCAN) modules
with configurable buffers
1 inter-integrated circuit (I2C) interface module
Up to 149 configurable general purpose pins
supporting input and output operations (package
dependent)
Real-Time Counter (RTC)
— Clock source from internal 128 kHz or 16 MHz
oscillator supporting autonomous wakeup with
1 ms resolution with maximum timeout of 2
seconds
— Optional support for RTC with clock source
from external 32 kHz crystal oscillator,
supporting wakeup with 1 sec resolution and
maximum timeout of 1 hour
Up to 8 periodic interrupt timers (PIT) with 32-bit
counter resolution
Nexus development interface (NDI) per IEEE-ISTO
5001-2003 Class Two Plus
Device/board boundary scan testing supported per
Joint Test Action Group (JTAG) of IEEE (IEEE
1149.1)
On-chip voltage regulator (VREG) for regulation of
input supply for all internal levels
Table of Contents
1
2
3
4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.1 Document overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Package pinouts and signal descriptions . . . . . . . . . . . . . . . . .8
3.1 Package pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.2
. . . . . . . . . . . . Pad configuration during reset phases12
3.3 Pad configuration during standby mode exit . . . . . . . . .13
3.4 Voltage supply pins . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.5 Pad types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.6 System pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.7 Functional port pins . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.8 Nexus 2+ pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.1 Parameter classification . . . . . . . . . . . . . . . . . . . . . . . .35
4.2 NVUSRO register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.2.1 NVUSRO[PAD3V5V] field description . . . . . . . .35
4.2.2 NVUSRO[OSCILLATOR_MARGIN] field description
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2.3 NVUSRO[WATCHDOG_EN] field description . .36
4.3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . .36
4.4 Recommended operating conditions . . . . . . . . . . . . . .37
4.5 Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . .40
4.5.1 External ballast resistor recommendations . . . .40
4.5.2 Package thermal characteristics . . . . . . . . . . . .40
4.5.3 Power considerations. . . . . . . . . . . . . . . . . . . . .41
4.6 I/O pad electrical characteristics . . . . . . . . . . . . . . . . . .42
4.6.1 I/O pad types . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.6.2 I/O input DC characteristics . . . . . . . . . . . . . . . .42
4.6.3 I/O output DC characteristics. . . . . . . . . . . . . . .43
4.6.4 Output pin transition times . . . . . . . . . . . . . . . . .46
4.6.5 I/O pad current specification . . . . . . . . . . . . . . .46
4.7 RESET electrical characteristics. . . . . . . . . . . . . . . . . .54
4.8 Power management electrical characteristics. . . . . . . .57
4.8.1 Voltage regulator electrical characteristics . . . .57
4.8.2 Low voltage detector electrical characteristics .59
5
6
4.9 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.10 Flash memory electrical characteristics . . . . . . . . . . . 62
4.10.1 Program/erase characteristics . . . . . . . . . . . . . 62
4.10.2 Flash power supply DC characteristics . . . . . . 63
4.10.3 Start-up/Switch-off timings . . . . . . . . . . . . . . . . 64
4.11 Electromagnetic compatibility (EMC) characteristics. . 64
4.11.1 Designing hardened software to avoid noise
problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.11.2 Electromagnetic interference (EMI) . . . . . . . . . 65
4.11.3 Absolute maximum ratings (electrical sensitivity)65
4.12 Fast external crystal oscillator (4 to 16 MHz) electrical
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.13 Slow external crystal oscillator (32 kHz) electrical
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.14 FMPLL electrical characteristics . . . . . . . . . . . . . . . . . 71
4.15 Fast internal RC oscillator (16 MHz) electrical
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.16 Slow internal RC oscillator (128 kHz) electrical
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.17 ADC electrical characteristics . . . . . . . . . . . . . . . . . . . 74
4.17.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.17.2 Input impedance and ADC accuracy . . . . . . . . 75
4.17.3 ADC electrical characteristics . . . . . . . . . . . . . 80
4.18 On-chip peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4.18.1 Current consumption . . . . . . . . . . . . . . . . . . . . 85
4.18.2 DSPI characteristics. . . . . . . . . . . . . . . . . . . . . 87
4.18.3 Nexus characteristics . . . . . . . . . . . . . . . . . . . . 93
4.18.4 JTAG characteristics. . . . . . . . . . . . . . . . . . . . . 94
Package characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
5.1 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . 96
5.1.1 176 LQFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
5.1.2 144 LQFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5.1.3 100 LQFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.1.4 208 MAPBGA. . . . . . . . . . . . . . . . . . . . . . . . . 105
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
MPC5607B Microcontroller Data Sheet, Rev. 8
2
Freescale Semiconductor
Introduction
1
Introduction
1.1
Document overview
This document describes the features of the family and options available within the family members, and highlights important
electrical and physical characteristics of the device.
1.2
Description
This family of 32-bit system-on-chip (SoC) microcontrollers is the latest achievement in integrated automotive application
controllers. It belongs to an expanding family of automotive-focused products designed to address the next wave of body
electronics applications within the vehicle.
The advanced and cost-efficient e200z0h host processor core of this automotive controller family complies with the
Power Architecture technology and only implements the VLE (variable-length encoding) APU (Auxiliary Processor Unit),
providing improved code density. It operates at speeds of up to 64 MHz and offers high performance processing optimized for
low power consumption. It capitalizes on the available development infrastructure of current Power Architecture devices and
is supported with software drivers, operating systems and configuration code to assist with users implementations.
Table 1. MPC5607B family comparison1
Feature
MPC5605B
MPC5606B
CPU
MPC5607B
e200z0h
Execution speed2
Up to 64 MHz
Code flash memory
768 KB
1 MB
1.5 MB
64 (4  16) KB
Data flash memory
SRAM
64 KB
80 KB
MPU
8-entry
eDMA
16 ch
10-bit ADC
96 KB
Yes
dedicated
3
7 ch
15 ch
29 ch
15 ch
shared with 12-bit ADC
29 ch
19 ch
12-bit ADC
Yes
dedicated
4
5 ch
shared with 10-bit ADC
Total timer I/O5 eMIOS
19 ch
37 ch,
16-bit
64 ch, 16-bit
Counter / OPWM / ICOC6
10 ch
O(I)PWM / OPWFMB /
OPWMCB / ICOC7
7 ch
O(I)PWM / ICOC8
7 ch
14 ch
ICOC9
13 ch
33 ch
OPWM /
SCI (LINFlex)
4
SPI (DSPI)
3
8
5
6
10
5
6
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
3
Introduction
Table 1. MPC5607B family comparison1 (continued)
Feature
MPC5605B
MPC5606B
CAN (FlexCAN)
6
2C
1
I
32 KHz oscillator
GPIO10
Yes
77
121
149
Debug
Package
MPC5607B
121
149
JTAG
100
LQFP
144
LQFP
176
LQFP
N2+
144
LQFP
176
LQFP
176
LQFP
208 MAP
BGA11
1
Feature set dependent on selected peripheral multiplexing; table shows example
Based on 125 C ambient operating temperature
3
Not shared with 12-bit ADC, but possibly shared with other alternate functions
4 Not shared with 10-bit ADC, but possibly shared with other alternate functions
5 See the eMIOS section of the chip reference manual for information on the channel configuration and functions.
6 Each channel supports a range of modes including Modulus counters, PWM generation, Input Capture, Output
Compare.
7 Each channel supports a range of modes including PWM generation with dead time, Input Capture, Output
Compare.
8 Each channel supports a range of modes including PWM generation, Input Capture, Output Compare, Period and
Pulse width measurement.
9 Each channel supports a range of modes including PWM generation, Input Capture, and Output Compare.
10 Maximum I/O count based on multiplexing with peripherals
11 208 MAPBGA available only as development package for Nexus2+
2
MPC5607B Microcontroller Data Sheet, Rev. 8
4
Freescale Semiconductor
Block diagram
2
Block diagram
Figure 1 shows a top-level block diagram of the MPC5607B.
SRAM
96 KB
eDMA
JTAG
JTAG Port
Code Flash
1.5 MB
Data Flash
64 KB
e200z0h
Nexus
(Master)
Data
NMI
Nexus 2+
(Master)
SIUL
Voltage
Regulator
Interrupt requests
from peripheral
blocks
NMI
INTC
Clocks
SRAM
Controller
MPU
Instructions
Nexus Port
64-bit 2  3 Crossbar Switch
(Master)
Flash
Controller
(Slave)
(Slave)
Interrupt
request with
wakeup
functionality
(Slave)
MPU
Registers
WKPU
CMU
FMPLL
RTC
STM
SWT
ECSM
MC_RGM
PIT
MC_CGM
MC_ME MC_PCU
BAM
SSCM
I2C
6
FlexCAN
Peripheral Bridge
Interrupt
Request
SIUL
Reset Control
19 ch 10-bit/12-bit
ADC
External
Interrupt
Request
29 ch 10-bit
ADC
10 
LINFlex
64 ch
eMIOS
CTU
6
DSPI
5 ch 12-bit
ADC
IMUX
GPIO &
Pad Control
I/O
...
...
...
...
...
Legend:
ADC
BAM
CMU
CTU
DSPI
ECSM
eDMA
eMIOS
Flash
FlexCAN
FMPLL
GPIO
I2C
IMUX
INTC
JTAG
LINFlex
Analog-to-Digital Converter
Boot Assist Module
Clock Monitor Unit
Cross Triggering Unit
Deserial Serial Peripheral Interface
Error Correction Status Module
Enhanced Direct Memory Access
Enhanced Modular Input Output System
Flash memory
Controller Area Network
Frequency-Modulated Phase-Locked Loop
General-purpose input/output
Inter-Integrated Circuit bus
Internal Multiplexer
Interrupt Controller
JTAG controller
Serial Communication Interface (LIN support)
MC_CGM
MC_ME
MC_PCU
MC_RGM
MPU
NMI
PIT
RTC
SIUL
SRAM
SSCM
STM
SWT
VREG
WKPU
XBAR
Clock Generation Module
Mode Entry Module
Power Control Unit
Reset Generation Module
Memory Protection Unit
Non-Maskable Interrupt
Periodic Interrupt Timer
Real-Time Clock
System Integration Unit Lite
Static Random-Access Memory
System Status Configuration Module
System Timer Module
Software Watchdog Timer
Voltage regulator
Wakeup Unit
Crossbar switch
Figure 1. MPC5607B block diagram
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
5
Block diagram
Table 2 summarizes the functions of the blocks present on the MPC5607B.
Table 2. MPC5607B series block summary
Block
Function
Analog-to-digital converter (ADC) Converts analog voltages to digital values
Boot assist module (BAM)
A block of read-only memory containing VLE code which is executed according
to the boot mode of the device
Clock generation module
(MC_CGM)
Provides logic and control required for the generation of system and peripheral
clocks
Clock monitor unit (CMU)
Monitors clock source (internal and external) integrity
Cross triggering unit (CTU)
Enables synchronization of ADC conversions with a timer event from the eMIOS
or from the PIT
Crossbar switch (XBAR)
Supports simultaneous connections between two master ports and three slave
ports. The crossbar supports a 32-bit address bus width and a 64-bit data bus
width.
Deserial serial peripheral interface Provides a synchronous serial interface for communication with external devices
(DSPI)
Enhanced direct memory access
(eDMA)
Performs complex data transfers with minimal intervention from a host processor
via “n” programmable channels
Enhanced modular input output
system (eMIOS)
Provides the functionality to generate or measure events
Error correction status module
(ECSM)
Provides a myriad of miscellaneous control functions for the device including
program-visible information about configuration and revision levels, a reset status
register, wakeup control for exiting sleep modes, and optional features such as
information on memory errors reported by error-correcting codes
Flash memory
Provides non-volatile storage for program code, constants and variables
FlexCAN (controller area network) Supports the standard CAN communications protocol
Frequency-modulated
phase-locked loop (FMPLL)
Generates high-speed system clocks and supports programmable frequency
modulation
Inter-integrated circuit (I2C) bus
Two-wire bidirectional serial bus that provides a simple and efficient method of
data exchange between devices
Internal multiplexer (IMUX) SIU
subblock
Allows flexible mapping of peripheral interface on the different pins of the device
Interrupt controller (INTC)
Provides priority-based preemptive scheduling of interrupt requests
JTAG controller (JTAGC)
Provides the means to test chip functionality and connectivity while remaining
transparent to system logic when not in test mode
LINFlex controller
Manages a high number of LIN (Local Interconnect Network protocol) messages
efficiently with a minimum of CPU load
Memory protection unit (MPU)
Provides hardware access control for all memory references generated in a
device
Mode entry module (MC_ME)
Provides a mechanism for controlling the device operational mode and
modetransition sequences in all functional states; also manages the power
control unit, reset generation module and clock generation module, and holds the
configuration, control and status registers accessible for applications
MPC5607B Microcontroller Data Sheet, Rev. 8
6
Freescale Semiconductor
Block diagram
Table 2. MPC5607B series block summary (continued)
Block
Function
Non-maskable interrupt (NMI)
Handles external events that must produce an immediate response, such as
power down detection
Periodic interrupt timer (PIT)
Produces periodic interrupts and triggers
Power control unit (MC_PCU)
Reduces the overall power consumption by disconnecting parts of the device
from the power supply via a power switching device; device components are
grouped into sections called “power domains” which are controlled by the PCU
Real-time counter (RTC)
A free running counter used for time keeping applications, the RTC can be
configured to generate an interrupt at a predefined interval independent of the
mode of operation (run mode or low-power mode)
Reset generation module
(MC_RGM)
Centralizes reset sources and manages the device reset sequence of the device
Static random-access memory
(SRAM)
Provides storage for program code, constants, and variables
System integration unit lite (SIUL) Provides control over all the electrical pad controls and up 32 ports with 16 bits
of bidirectional, general-purpose input and output signals and supports up to 32
external interrupts with trigger event configuration
System status and configuration
module (SSCM)
Provides system configuration and status data (such as memory size and status,
device mode and security status), device identification data, debug status port
enable and selection, and bus and peripheral abort enable/disable
System timer module (STM)
Provides a set of output compare events to support AUTOSAR (Automotive Open
System Architecture) and operating system tasks
Software watchdog timer (SWT)
Provides protection from runaway code
Wakeup unit (WKPU)
The wakeup unit supports up to 27 external sources that can generate interrupts
or wakeup events, of which 1 can cause non-maskable interrupt requests or
wakeup events.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
7
Package pinouts and signal descriptions
3
Package pinouts and signal descriptions
3.1
Package pinouts
The available LQFP pinouts and the ballmap are provided in the following figures. For pin signal descriptions, please see
Table 5.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
176 LQFP
Top view
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
PA[11]
PA[10]
PA[9]
PA[8]
PA[7]
PE[13]
PF[14]
PF[15]
VDD_HV
VSS_HV
PG[0]
PG[1]
PH[3]
PH[2]
PH[1]
PH[0]
PG[12]
PG[13]
PA[3]
PI[13]
PI[12]
PI[11]
PI[10]
PI[9]
PI[8]
PB[15]
PD[15]
PB[14]
PD[14]
PB[13]
PD[13]
PB[12]
PD[12]
VDD_HV_ADC1
VSS_HV_ADC1
PB[11]
PD[11]
PD[10]
PD[9]
PB[7]
PB[6]
PB[5]
VDD_HV_ADC0
VSS_HV_ADC0
PC[7]
PF[10]
PF[11]
PA[15]
PF[13]
PA[14]
PA[4]
PA[13]
PA[12]
VDD_LV
VSS_LV
XTAL
VSS_HV
EXTAL
VDD_HV
PB[9]
PB[8]
PB[10]
PF[0]
PF[1]
PF[2]
PF[3]
PF[4]
PF[5]
PF[6]
PF[7]
PJ[3]
PJ[2]
PJ[1]
PJ[0]
PI[15]
PI[14]
PD[0]
PD[1]
PD[2]
PD[3]
PD[4]
PD[5]
PD[6]
PD[7]
VDD_HV
VSS_HV
PD[8]
PB[4]
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
PB[3]
PC[9]
PC[14]
PC[15]
PJ[4]
VDD_HV
VSS_HV
PH[15]
PH[13]
PH[14]
PI[6]
PI[7]
PG[5]
PG[4]
PG[3]
PG[2]
PA[2]
PE[0]
PA[1]
PE[1]
PE[8]
PE[9]
PE[10]
PA[0]
PE[11]
VSS_HV
VDD_HV
VSS_HV
RESET
VSS_LV
VDD_LV
VDD_BV
PG[9]
PG[8]
PC[11]
PC[10]
PG[7]
PG[6]
PB[0]
PB[1]
PF[9]
PF[8]
PF[12]
PC[6]
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
PB[2]
PC[8]
PC[13]
PC[12]
PI[0]
PI[1]
PI[2]
PI[3]
PE[7]
PE[6]
PH[8]
PH[7]
PH[6]
PH[5]
PH[4]
PE[5]
PE[4]
PC[4]
PC[5]
PE[3]
PE[2]
PH[9]
PC[0]
VSS_LV
VDD_LV
VDD_HV
VSS_HV
PC[1]
PH[10]
PA[6]
PA[5]
PC[2]
PC[3]
PI[4]
PI[5]
PH[12]
PH[11]
PG[11]
PG[10]
PE[15]
PE[14]
PG[15]
PG[14]
PE[12]
Figure 2 shows the MPC5607B in the 176 LQFP package.
Figure 2. 176 LQFP pin configuration
MPC5607B Microcontroller Data Sheet, Rev. 8
8
Freescale Semiconductor
Package pinouts and signal descriptions
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
PB[2]
PC[8]
PC[13]
PC[12]
PE[7]
PE[6]
PH[8]
PH[7]
PH[6]
PH[5]
PH[4]
PE[5]
PE[4]
PC[4]
PC[5]
PE[3]
PE[2]
PH[9]
PC[0]
VSS_LV
VDD_LV
VDD_HV
VSS_HV
PC[1]
PH[10]
PA[6]
PA[5]
PC[2]
PC[3]
PG[11]
PG[10]
PE[15]
PE[14]
PG[15]
PG[14]
PE[12]
Figure 3 shows the MPC5607B in the 144 LQFP package.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
144 LQFP
Top view
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
PA[11]
PA[10]
PA[9]
PA[8]
PA[7]
PE[13]
PF[14]
PF[15]
VDD_HV
VSS_HV
PG[0]
PG[1]
PH[3]
PH[2]
PH[1]
PH[0]
PG[12]
PG[13]
PA[3]
PB[15]
PD[15]
PB[14]
PD[14]
PB[13]
PD[13]
PB[12]
VDD_HV_ADC1
VSS_HV_ADC1
PD[11]
PD[10]
PD[9]
PB[7]
PB[6]
PB[5]
VDD_HV_ADC0
VSS_HV_ADC0
PC[7]
PF[10]
PF[11]
PA[15]
PF[13]
PA[14]
PA[4]
PA[13]
PA[12]
VDD_LV
VSS_LV
XTAL
VSS_HV
EXTAL
VDD_HV
PB[9]
PB[8]
PB[10]
PF[0]
PF[1]
PF[2]
PF[3]
PF[4]
PF[5]
PF[6]
PF[7]
PD[0]
PD[1]
PD[2]
PD[3]
PD[4]
PD[5]
PD[6]
PD[7]
PD[8]
PB[4]
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
PB[3]
PC[9]
PC[14]
PC[15]
PG[5]
PG[4]
PG[3]
PG[2]
PA[2]
PE[0]
PA[1]
PE[1]
PE[8]
PE[9]
PE[10]
PA[0]
PE[11]
VSS_HV
VDD_HV
VSS_HV
RESET
VSS_LV
VDD_LV
VDD_BV
PG[9]
PG[8]
PC[11]
PC[10]
PG[7]
PG[6]
PB[0]
PB[1]
PF[9]
PF[8]
PF[12]
PC[6]
Figure 3. 144 LQFP pin configuration
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
9
Package pinouts and signal descriptions
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
PB[2]
PC[8]
PC[13]
PC[12]
PE[7]
PE[6]
PE[5]
PE[4]
PC[4]
PC[5]
PE[3]
PE[2]
PH[9]
PC[0]
VSS_LV
VDD_LV
VDD_HV
VSS_HV
PC[1]
PH[10]
PA[6]
PA[5]
PC[2]
PC[3]
PE[12]
Figure 4 shows the MPC5607B in the 100 LQFP package.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
100 LQFP
Top view
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
PA[11]
PA[10]
PA[9]
PA[8]
PA[7]
VDD_HV
VSS_HV
PA[3]
PB[15]
PD[15]
PB[14]
PD[14]
PB[13]
PD[13]
PB[12]
VDD_HV_ADC1
VSS_HV_ADC1
PD[11]
PD[10]
PD[9]
PB[7]
PB[6]
PB[5]
VDD_HV_ADC0
VSS_HV_ADC0
PC[7]
PA[15]
PA[14]
PA[4]
PA[13]
PA[12]
VDD_LV
VSS_LV
XTAL
VSS_HV
EXTAL
VDD_HV
PB[9]
PB[8]
PB[10]
PD[0]
PD[1]
PD[2]
PD[3]
PD[4]
PD[5]
PD[6]
PD[7]
PD[8]
PB[4]
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PB[3]
PC[9]
PC[14]
PC[15]
PA[2]
PE[0]
PA[1]
PE[1]
PE[8]
PE[9]
PE[10]
PA[0]
PE[11]
VSS_HV
VDD_HV
VSS_HV
RESET
VSS_LV
VDD_LV
VDD_BV
PC[11]
PC[10]
PB[0]
PB[1]
PC[6]
Figure 4. 100 LQFP pin configuration
Figure 5 shows the MPC5607B in the 208 MAPBGA package.
MPC5607B Microcontroller Data Sheet, Rev. 8
10
Freescale Semiconductor
Package pinouts and signal descriptions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A
PC[8]
PC[13]
PH[15]
PJ[4]
PH[8]
PH[4]
PC[5]
PC[0]
PI[0]
PI[1]
PC[2]
PI[4]
PE[15]
PH[11]
NC
NC
A
B
PC[9]
PB[2]
PH[13]
PC[12]
PE[6]
PH[5]
PC[4]
PH[9]
PH[10]
PI[2]
PC[3]
PG[11]
PG[15]
PG[14]
PA[11]
PA[10]
B
C
PC[14]
VDD_HV
PB[3]
PE[7]
PH[7]
PE[5]
PE[3]
VSS_LV
PC[1]
PI[3]
PA[5]
PI[5]
PE[14]
PE[12]
PA[9]
PA[8]
C
D
PH[14]
PI[6]
PC[15]
PI[7]
PH[6]
PE[4]
PE[2]
VDD_LV
VDD_HV
NC
PA[6]
PH[12]
PG[10]
PF[14]
PE[13]
PA[7]
D
E
PG[4]
PG[5]
PG[3]
PG[2]
PG[1]
PG[0]
PF[15]
VDD_HV
E
F
PE[0]
PA[2]
PA[1]
PE[1]
PH[0]
PH[1]
PH[3]
PH[2]
F
G
PE[9]
PE[8]
PE[10]
PA[0]
VSS_HV VSS_HV VSS_HV VSS_HV
VDD_HV
PI[12]
PI[13]
MSEO
G
H
VSS_HV
PE[11]
VDD_HV
NC
VSS_HV VSS_HV VSS_HV VSS_HV
MDO3
MDO2
MDO0
MDO1
H
J
RESET
VSS_LV
NC
NC
VSS_HV VSS_HV VSS_HV VSS_HV
PI[8]
PI[9]
PI[10]
PI[11]
J
K
EVTI
NC
VDD_BV
VDD_LV
VSS_HV VSS_HV VSS_HV VSS_HV
VDD_HV
_ADC1
PG[12]
PA[3]
PG[13]
K
L
PG[9]
PG[8]
NC
EVTO
PB[15]
PD[15]
PD[14]
PB[14]
L
M
PG[7]
PG[6]
PC[10]
PC[11]
PB[13]
PD[13]
PD[12]
PB[12]
M
N
PB[1]
PF[9]
PB[0]
VDD_HV
PJ[0]
PA[4]
VSS_LV
EXTAL
VDD_HV
PF[0]
PF[4]
VSS_HV
_ADC1
PB[11]
PD[10]
PD[9]
PD[11]
N
P
PF[8]
PJ[3]
PC[7]
PJ[2]
PJ[1]
PA[14]
VDD_LV
XTAL
PB[10]
PF[1]
PF[5]
PD[0]
PD[3]
VDD_HV
_ADC0
PB[6]
PB[7]
P
R
PF[12]
PC[6]
PF[10]
PF[11]
VDD_HV
PA[15]
PA[13]
PI[14]
XTAL32
PF[3]
PF[7]
PD[2]
PD[4]
PD[7]
VSS_HV
_ADC0
PB[5]
R
T
NC
NC
NC
MCKO
NC
PF[13]
PA[12]
PI[15]
EXTAL
32
PF[2]
PF[6]
PD[1]
PD[5]
PD[6]
PD[8]
PB[4]
T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NOTE: The 208 MAPBGA is available only as development package for Nexus 2+.
NC
= Not connected
Figure 5. 208 MAPBGA configuration
3.2
Pad configuration during reset phases
All pads have a fixed configuration under reset.
During the power-up phase, all pads are forced to tristate.
After power-up phase, all pads are tristate with the following exceptions:
•
•
•
•
PA[9] (FAB) is pull-down. Without external strong pull-up the device starts fetching from flash.
PA[8], PC[0] and PH[9:10] are in input weak pull-up when out of reset.
RESET pad is driven low by the device till 40 FIRC clock cycles after phase2 completion. Minimum phase3 duration
is 40 FIRC cycles.
Nexus output pads (MDO[n], MCKO, EVTO, MSEO) are forced to output.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
11
Package pinouts and signal descriptions
3.3
Pad configuration during standby mode exit
Pad configuration (input buffer enable, pull enable) for low-power wakeup pads is controlled by both the SIUL and WKPU
modules. During standby exit, all low power pads PA[0,1,2,4,15], PB[1,3,8,9,10]1, PC[7,9,11], PD[0,1], PE[0,9,11],
PF[9,11,13]2, PG[3,5,7,9]2, PI[1,3]3 are configured according to their respective configuration done in the WKPU module. All
other pads will have the same configuration as expected after a reset.
The TDO pad has been moved into the STANDBY domain in order to allow low-power debug handshaking in STANDBY
mode. However, no pull-resistor is active on the TDO pad while in STANDBY mode. At this time the pad is configured as an
input. When no debugger is connected the TDO pad is floating causing additional current consumption.
To avoid the extra consumption TDO must be connected. An external pull-up resistor in the range of 47–100 kOhms should be
added between the TDO pin and VDD. Only if the TDO pin is used as an application pin and a pull-up cannot be used should
a pull-down resistor with the same value be used instead between the TDO pin and GND.
3.4
Voltage supply pins
Voltage supply pins are used to provide power to the device. Three dedicated VDD_LV/VSS_LV supply pairs are used for 1.2 V
regulator stabilization.
Table 3. Voltage supply pin descriptions
Pin number
Port pin
Function
100 LQFP
144 LQFP
19, 51, 100,
123
176 LQFP
208 MAPBGA
VDD_HV
Digital supply voltage
15, 37, 70, 84
6, 27, 59, 85, C2, D9, E16,
124, 151
G13, H3, N4,
N9, R5
VSS_HV
Digital ground
14, 16, 35, 69, 18, 20, 49, 99, 7, 26, 28, 57, G7, G8, G9,
83
122
86, 123, 150 G10, H7, H8,
H9, H10, J7,
J8, J9, J10,
K7, K8, K9,
K10
VDD_LV
1.2 V decoupling pins. Decoupling
capacitor must be connected
between these pins and the nearest
VSS_LV pin.1
19, 32, 85
23, 46, 124
31, 54, 152
D8, K4, P7
VSS_LV
1.2 V decoupling pins. Decoupling
capacitor must be connected
between these pins and the nearest
VDD_LV pin.1
18, 33, 86
22, 47, 125
30, 55, 153
C8, J2, N7
VDD_BV
Internal regulator supply voltage
20
24
32
K3
VSS_HV_ADC0 Reference ground and analog ground
for the A/D converter 0 (10-bit)
51
73
89
R15
VDD_HV_ADC0 Reference voltage and analog supply
for the A/D converter 0 (10-bit)
52
74
90
P14
VSS_HV_ADC1 Reference ground and analog ground
for the A/D converter 1 (12-bit)
59
81
98
N12
1. PB[8, 9] ports have wakeup functionality in all modes except STANDBY.
2. PF[9,11,13], PG[3,5,7,9], PI[1,3] are not available in the 100-pin LQFP.
3. PI[1,3] are not available in the 144-pin LQFP.
MPC5607B Microcontroller Data Sheet, Rev. 8
12
Freescale Semiconductor
Package pinouts and signal descriptions
Table 3. Voltage supply pin descriptions (continued)
Pin number
Port pin
Function
100 LQFP
144 LQFP
176 LQFP
208 MAPBGA
60
82
99
K13
VDD_HV_ADC1 Reference voltage and analog supply
for the A/D converter 1 (12-bit)
1
A decoupling capacitor must be placed between each of the three VDD_LV/VSS_LV supply pairs to ensure stable
voltage (see the recommended operating conditions in the device data sheet).
3.5
Pad types
In the device the following types of pads are available for system pins and functional port pins:
S = Slow1
M = Medium1 2
F = Fast1 2
I = Input only with analog feature1
J = Input/Output (‘S’ pad) with analog feature
X = Oscillator
3.6
System pins
The system pins are listed in Table 4.
RESET
configuration
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
1
RESET Bidirectional reset with Schmitt-Trigger I/O
characteristics and noise filter.
M
Input weak
pull-up after
RGM PHASE2
and 40 FIRC
cycles
17
21
29
J1
EXTAL Analog output of the oscillator
I/O
amplifier circuit, when the oscillator is
not in bypass mode.
Analog input for the clock generator
when the oscillator is in bypass mode.
X
Tristate
36
50
58
N8
X
Tristate
34
48
56
P8
XTAL
1
Function
Pin number
Pad type
Port pin
I/O direction
Table 4. System pin descriptions
Analog input of the oscillator amplifier
circuit. Needs to be grounded if
oscillator bypass mode is used.
I
208 MAPBGA available only as development package for Nexus2+
1. See the I/O pad electrical characteristics in the chip data sheet for details.
2. All medium and fast pads are in slow configuration by default at reset and can be configured as fast or medium. The only
exception is PC[1] which is in medium configuration by default (see the PCR.SRC description in the chip reference manual, Pad
Configuration Registers (PCR0–PCR148)).
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
13
Package pinouts and signal descriptions
3.7
Functional port pins
The functional port pins are listed in Table 5.
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
Port A
PA[0]
PCR[0]
AF0
AF1
AF2
AF3
—
GPIO[0]
E0UC[0]
CLKOUT
E0UC[13]
WKPU[19]5
SIUL
eMIOS_0
MC_CGM
eMIOS_0
WKPU
I/O
I/O
O
I/O
I
M
Tristate
12
16
24
G4
PA[1]
PCR[1]
AF0
AF1
AF2
AF3
—
GPIO[1]
E0UC[1]
NMI6
—
WKPU[2]5
SIUL
eMIOS_0
WKPU
—
WKPU
I/O
I/O
I
—
I
S
Tristate
7
11
19
F3
PA[2]
PCR[2]
AF0
AF1
AF2
AF3
—
GPIO[2]
E0UC[2]
—
MA[2]
WKPU[3]5
SIUL
eMIOS_0
—
ADC_0
WKPU
I/O
I/O
—
O
I
S
Tristate
5
9
17
F2
PA[3]
PCR[3]
AF0
AF1
AF2
AF3
—
—
GPIO[3]
E0UC[3]
LIN5TX
CS4_1
EIRQ[0]
ADC1_S[0]
SIUL
eMIOS_0
LINFlex_5
DSPI_1
SIUL
ADC_1
I/O
I/O
O
O
I
I
J
Tristate
68
90
114
K15
PA[4]
PCR[4]
AF0
AF1
AF2
AF3
—
—
GPIO[4]
E0UC[4]
—
CS0_1
LIN5RX
WKPU[9]5
SIUL
eMIOS_0
—
DSPI_1
LINFlex_5
WKPU
I/O
I/O
—
I/O
I
I
S
Tristate
29
43
51
N6
PA[5]
PCR[5]
AF0
AF1
AF2
AF3
GPIO[5]
E0UC[5]
LIN4TX
—
SIUL
eMIOS_0
LINFlex_4
—
I/O
I/O
O
—
M
Tristate
79
118
146
C11
PA[6]
PCR[6]
AF0
AF1
AF2
AF3
—
—
GPIO[6]
E0UC[6]
—
CS1_1
EIRQ[1]
LIN4RX
SIUL
eMIOS_0
—
DSPI_1
SIUL
LINFlex_4
I/O
I/O
—
O
I
I
S
Tristate
80
119
147
D11
MPC5607B Microcontroller Data Sheet, Rev. 8
14
Freescale Semiconductor
Package pinouts and signal descriptions
PCR[7]
AF0
AF1
AF2
AF3
—
—
GPIO[7]
E0UC[7]
LIN3TX
—
EIRQ[2]
ADC1_S[1]
SIUL
eMIOS_0
LINFlex_3
—
SIUL
ADC_1
I/O
I/O
O
—
I
I
J
Tristate
71
104
128
D16
PA[8]
PCR[8]
AF0
AF1
AF2
AF3
—
N/A7
—
GPIO[8]
E0UC[8]
E0UC[14]
—
EIRQ[3]
ABS[0]
LIN3RX
SIUL
eMIOS_0
eMIOS_0
—
SIUL
BAM
LINFlex_3
I/O
I/O
I/O
—
I
I
I
S
Input,
weak
pull-up
72
105
129
C16
PA[9]
PCR[9]
AF0
AF1
AF2
AF3
N/A7
GPIO[9]
E0UC[9]
—
CS2_1
FAB
SIUL
eMIOS_0
—
DSPI_1
BAM
I/O
I/O
—
O
I
S
Pulldown
73
106
130
C15
PA[10]
PCR[10] AF0
AF1
AF2
AF3
—
GPIO[10]
E0UC[10]
SDA
LIN2TX
ADC1_S[2]
SIUL
eMIOS_0
I2C_0
LINFlex_2
ADC_1
I/O
I/O
I/O
O
I
J
Tristate
74
107
131
B16
PA[11]
PCR[11] AF0
AF1
AF2
AF3
—
—
—
GPIO[11]
E0UC[11]
SCL
—
EIRQ[16]
LIN2RX
ADC1_S[3]
SIUL
eMIOS_0
I2C_0
—
SIUL
LINFlex_2
ADC_1
I/O
I/O
I/O
—
I
I
I
J
Tristate
75
108
132
B15
PA[12]
PCR[12] AF0
AF1
AF2
AF3
—
—
GPIO[12]
—
E0UC[28]
CS3_1
EIRQ[17]
SIN_0
SIUL
—
eMIOS_0
DSPI_1
SIUL
DSPI_0
I/O
—
I/O
O
I
I
S
Tristate
31
45
53
T7
PA[13]
PCR[13] AF0
AF1
AF2
AF3
GPIO[13]
SOUT_0
E0UC[29]
—
SIUL
DSPI_0
eMIOS_0
—
I/O
O
I/O
—
M
Tristate
30
44
52
R7
Peripheral
RESET
configuration3
PA[7]
PCR
Pad type
Function
Port pin
I/O direction2
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
15
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PA[14]
PCR[14] AF0
AF1
AF2
AF3
—
GPIO[14]
SCK_0
CS0_0
E0UC[0]
EIRQ[4]
SIUL
DSPI_0
DSPI_0
eMIOS_0
SIUL
I/O
I/O
I/O
I/O
I
M
Tristate
28
42
50
P6
PA[15]
PCR[15] AF0
AF1
AF2
AF3
—
GPIO[15]
CS0_0
SCK_0
E0UC[1]
WKPU[10]5
SIUL
DSPI_0
DSPI_0
eMIOS_0
WKPU
I/O
I/O
I/O
I/O
I
M
Tristate
27
40
48
R6
Port B
PB[0]
PCR[16] AF0
AF1
AF2
AF3
GPIO[16]
CAN0TX
E0UC[30]
LIN0TX
SIUL
I/O
FlexCAN_0 O
eMIOS_0 I/O
LINFlex_0 O
M
Tristate
23
31
39
N3
PB[1]
PCR[17] AF0
AF1
AF2
AF3
—
—
—
GPIO[17]
—
E0UC[31]
—
WKPU[4]5
CAN0RX
LIN0RX
SIUL
I/O
—
—
eMIOS_0 I/O
—
—
WKPU
I
FlexCAN_0 I
LINFlex_0
I
S
Tristate
24
32
40
N1
PB[2]
PCR[18] AF0
AF1
AF2
AF3
GPIO[18]
LIN0TX
SDA
E0UC[30]
SIUL
LINFlex_0
I2C_0
eMIOS_0
I/O
O
I/O
I/O
M
Tristate
100
144
176
B2
PB[3]
PCR[19] AF0
AF1
AF2
AF3
—
—
GPIO[19]
E0UC[31]
SCL
—
WKPU[11]5
LIN0RX
SIUL
eMIOS_0
I2C_0
—
WKPU
LINFlex_0
I/O
I/O
I/O
—
I
I
S
Tristate
1
1
1
C3
PB[4]
PCR[20] AF0
AF1
AF2
AF3
—
—
—
—
—
—
—
ADC0_P[0]
ADC1_P[0]
GPIO[20]
—
—
—
—
ADC_0
ADC_1
SIUL
—
—
—
—
I
I
I
I
Tristate
50
72
88
T16
MPC5607B Microcontroller Data Sheet, Rev. 8
16
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PB[5]
PCR[21] AF0
AF1
AF2
AF3
—
—
—
—
—
—
—
ADC0_P[1]
ADC1_P[1]
GPIO[21]
—
—
—
—
ADC_0
ADC_1
SIUL
—
—
—
—
I
I
I
I
Tristate
53
75
91
R16
PB[6]
PCR[22] AF0
AF1
AF2
AF3
—
—
—
—
—
—
—
ADC0_P[2]
ADC1_P[2]
GPIO[22]
—
—
—
—
ADC_0
ADC_1
SIUL
—
—
—
—
I
I
I
I
Tristate
54
76
92
P15
PB[7]
PCR[23] AF0
AF1
AF2
AF3
—
—
—
—
—
—
—
ADC0_P[3]
ADC1_P[3]
GPIO[23]
—
—
—
—
ADC_0
ADC_1
SIUL
—
—
—
—
I
I
I
I
Tristate
55
77
93
P16
PB[8]
PCR[24] AF0
AF1
AF2
AF3
—
—
—
—
GPIO[24]
—
—
—
OSC32K_XTAL8
WKPU[25]5
ADC0_S[0]
ADC1_S[4]
SIUL
—
—
—
OSC32K
WKPU
ADC_0
ADC_1
I
—
—
—
—
I9
I
I
I
—
39
53
61
R9
PB[9]
PCR[25] AF0
GPIO[25]
AF1
—
AF2
—
AF3
—
— OSC32K_EXTAL8
WKPU[26]5
—
ADC0_S[1]
—
ADC1_S[5]
—
SIUL
—
—
—
OSC32K
WKPU
ADC_0
ADC_1
I
—
—
—
—
I9
I
I
I
—
38
52
60
T9
PB[10]
PCR[26] AF0
AF1
AF2
AF3
—
—
—
SIUL
—
—
—
WKPU
ADC_0
ADC_1
I/O
—
—
—
I
I
I
J
Tristate
40
54
62
P9
GPIO[26]
—
—
—
WKPU[8]5
ADC0_S[2]
ADC1_S[6]
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
17
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PB[11]
PCR[27] AF0
AF1
AF2
AF3
—
GPIO[27]
E0UC[3]
—
CS0_0
ADC0_S[3]
SIUL
eMIOS_0
—
DSPI_0
ADC_0
I/O
I/O
—
I/O
I
J
Tristate
—
—
97
N13
PB[12]
PCR[28] AF0
AF1
AF2
AF3
—
GPIO[28]
E0UC[4]
—
CS1_0
ADC0_X[0]
SIUL
eMIOS_0
—
DSPI_0
ADC_0
I/O
I/O
—
O
I
J
Tristate
61
83
101
M16
PB[13]
PCR[29] AF0
AF1
AF2
AF3
—
GPIO[29]
E0UC[5]
—
CS2_0
ADC0_X[1]
SIUL
eMIOS_0
—
DSPI_0
ADC_0
I/O
I/O
—
O
I
J
Tristate
63
85
103
M13
PB[14]
PCR[30] AF0
AF1
AF2
AF3
—
GPIO[30]
E0UC[6]
—
CS3_0
ADC0_X[2]
SIUL
eMIOS_0
—
DSPI_0
ADC_0
I/O
I/O
—
O
I
J
Tristate
65
87
105
L16
PB[15]
PCR[31] AF0
AF1
AF2
AF3
—
GPIO[31]
E0UC[7]
—
CS4_0
ADC0_X[3]
SIUL
eMIOS_0
—
DSPI_0
ADC_0
I/O
I/O
—
O
I
J
Tristate
67
89
107
L13
M
Port C
PC[0]10
PCR[32] AF0
AF1
AF2
AF3
GPIO[32]
—
TDI
—
SIUL
—
JTAGC
—
I/O
—
I
—
Input,
weak
pull-up
87
126
154
A8
PC[1]10
PCR[33] AF0
AF1
AF2
AF3
GPIO[33]
—
TDO
—
SIUL
—
JTAGC
—
I/O F11 Tristate
—
O
—
82
121
149
C9
PC[2]
PCR[34] AF0
AF1
AF2
AF3
—
GPIO[34]
SCK_1
CAN4TX
DEBUG[0]
EIRQ[5]
78
117
145
A11
SIUL
I/O
DSPI_1
I/O
FlexCAN_4 O
SSCM
O
SIUL
I
M
Tristate
MPC5607B Microcontroller Data Sheet, Rev. 8
18
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PC[3]
PCR[35] AF0
AF1
AF2
AF3
—
—
—
GPIO[35]
CS0_1
MA[0]
DEBUG[1]
EIRQ[6]
CAN1RX
CAN4RX
SIUL
I/O
DSPI_1
I/O
ADC_0
O
SSCM
O
SIUL
I
FlexCAN_1 I
FlexCAN_4 I
S
Tristate
77
116
144
B11
PC[4]
PCR[36] AF0
AF1
AF2
AF3
—
—
—
GPIO[36]
E1UC[31]
—
DEBUG[2]
EIRQ[18]
SIN_1
CAN3RX
SIUL
I/O
eMIOS_1 I/O
—
—
SSCM
O
SIUL
I
DSPI_1
I
FlexCAN_3 I
M
Tristate
92
131
159
B7
PC[5]
PCR[37] AF0
AF1
AF2
AF3
—
GPIO[37]
SOUT_1
CAN3TX
DEBUG[3]
EIRQ[7]
SIUL
I/O
DSPI_1
O
FlexCAN_3 O
SSCM
O
SIUL
I
M
Tristate
91
130
158
A7
PC[6]
PCR[38] AF0
AF1
AF2
AF3
GPIO[38]
LIN1TX
E1UC[28]
DEBUG[4]
SIUL
LINFlex_1
eMIOS_1
SSCM
I/O
O
I/O
O
S
Tristate
25
36
44
R2
PC[7]
PCR[39] AF0
AF1
AF2
AF3
—
—
GPIO[39]
—
E1UC[29]
DEBUG[5]
LIN1RX
WKPU[12]5
SIUL
—
eMIOS_1
SSCM
LINFlex_1
WKPU
I/O
—
I/O
O
I
I
S
Tristate
26
37
45
P3
PC[8]
PCR[40] AF0
AF1
AF2
AF3
GPIO[40]
LIN2TX
E0UC[3]
DEBUG[6]
SIUL
LINFlex_2
eMIOS_0
SSCM
I/O
O
I/O
O
S
Tristate
99
143
175
A1
PC[9]
PCR[41] AF0
AF1
AF2
AF3
—
—
GPIO[41]
—
E0UC[7]
DEBUG[7]
WKPU[13]5
LIN2RX
SIUL
—
eMIOS_0
SSCM
WKPU
LINFlex_2
I/O
—
I/O
O
I
I
S
Tristate
2
2
2
B1
PC[10]
PCR[42] AF0
AF1
AF2
AF3
GPIO[42]
CAN1TX
CAN4TX
MA[1]
SIUL
I/O
FlexCAN_1 O
FlexCAN_4 O
O
ADC_0
M
Tristate
22
28
36
M3
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
19
Package pinouts and signal descriptions
Peripheral
PC[11]
PCR[43] AF0
AF1
AF2
AF3
—
—
—
GPIO[43]
—
—
MA[2]
WKPU[5]5
CAN1RX
CAN4RX
PC[12]
PCR[44] AF0
AF1
AF2
AF3
—
—
GPIO[44]
E0UC[12]
—
—
EIRQ[19]
SIN_2
SIUL
eMIOS_0
—
—
SIUL
DSPI_2
PC[13]
PCR[45] AF0
AF1
AF2
AF3
GPIO[45]
E0UC[13]
SOUT_2
—
PC[14]
PCR[46] AF0
AF1
AF2
AF3
—
PC[15]
PCR[47] AF0
AF1
AF2
AF3
—
SIUL
I/O
—
—
—
—
ADC_0
O
WKPU
I
FlexCAN_1 I
FlexCAN_4 I
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
S
Tristate
21
27
35
M4
I/O
I/O
—
—
I
I
M
Tristate
97
141
173
B4
SIUL
eMIOS_0
DSPI_2
—
I/O
I/O
O
—
S
Tristate
98
142
174
A2
GPIO[46]
E0UC[14]
SCK_2
—
EIRQ[8]
SIUL
eMIOS_0
DSPI_2
—
SIUL
I/O
I/O
I/O
—
I
S
Tristate
3
3
3
C1
GPIO[47]
E0UC[15]
CS0_2
—
EIRQ[20]
SIUL
eMIOS_0
DSPI_2
—
SIUL
I/O
I/O
I/O
—
I
M
Tristate
4
4
4
D3
Port D
PD[0]
PCR[48] AF0
AF1
AF2
AF3
—
—
—
GPIO[48]
—
—
—
WKPU[27]5
ADC0_P[4]
ADC1_P[4]
SIUL
—
—
—
WKPU
ADC_0
ADC_1
I
—
—
—
I
I
I
I
Tristate
41
63
77
P12
PD[1]
PCR[49] AF0
AF1
AF2
AF3
—
—
—
GPIO[49]
—
—
—
WKPU[28]5
ADC0_P[5]
ADC1_P[5]
SIUL
—
—
—
WKPU
ADC_0
ADC_1
I
—
—
—
I
I
I
I
Tristate
42
64
78
T12
MPC5607B Microcontroller Data Sheet, Rev. 8
20
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PD[2]
PCR[50] AF0
AF1
AF2
AF3
—
—
GPIO[50]
—
—
—
ADC0_P[6]
ADC1_P[6]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
43
65
79
R12
PD[3]
PCR[51] AF0
AF1
AF2
AF3
—
—
GPIO[51]
—
—
—
ADC0_P[7]
ADC1_P[7]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
44
66
80
P13
PD[4]
PCR[52] AF0
AF1
AF2
AF3
—
—
GPIO[52]
—
—
—
ADC0_P[8]
ADC1_P[8]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
45
67
81
R13
PD[5]
PCR[53] AF0
AF1
AF2
AF3
—
—
GPIO[53]
—
—
—
ADC0_P[9]
ADC1_P[9]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
46
68
82
T13
PD[6]
PCR[54] AF0
AF1
AF2
AF3
—
—
GPIO[54]
—
—
—
ADC0_P[10]
ADC1_P[10]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
47
69
83
T14
PD[7]
PCR[55] AF0
AF1
AF2
AF3
—
—
GPIO[55]
—
—
—
ADC0_P[11]
ADC1_P[11]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
48
70
84
R14
PD[8]
PCR[56] AF0
AF1
AF2
AF3
—
—
GPIO[56]
—
—
—
ADC0_P[12]
ADC1_P[12]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
49
71
87
T15
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
21
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PD[9]
PCR[57] AF0
AF1
AF2
AF3
—
—
GPIO[57]
—
—
—
ADC0_P[13]
ADC1_P[13]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
56
78
94
N15
PD[10]
PCR[58] AF0
AF1
AF2
AF3
—
—
GPIO[58]
—
—
—
ADC0_P[14]
ADC1_P[14]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
57
79
95
N14
PD[11]
PCR[59] AF0
AF1
AF2
AF3
—
—
GPIO[59]
—
—
—
ADC0_P[15]
ADC1_P[15]
SIUL
—
—
—
ADC_0
ADC_1
I
—
—
—
I
I
I
Tristate
58
80
96
N16
PD[12]
PCR[60] AF0
AF1
AF2
AF3
—
GPIO[60]
CS5_0
E0UC[24]
—
ADC0_S[4]
SIUL
DSPI_0
eMIOS_0
—
ADC_0
I/O
O
I/O
—
I
J
Tristate
—
—
100
M15
PD[13]
PCR[61] AF0
AF1
AF2
AF3
—
GPIO[61]
CS0_1
E0UC[25]
—
ADC0_S[5]
SIUL
DSPI_1
eMIOS_0
—
ADC_0
I/O
I/O
I/O
—
I
J
Tristate
62
84
102
M14
PD[14]
PCR[62] AF0
AF1
AF2
AF3
—
GPIO[62]
CS1_1
E0UC[26]
—
ADC0_S[6]
SIUL
DSPI_1
eMIOS_0
—
ADC_0
I/O
O
I/O
—
I
J
Tristate
64
86
104
L15
PD[15]
PCR[63] AF0
AF1
AF2
AF3
—
GPIO[63]
CS2_1
E0UC[27]
—
ADC0_S[7]
SIUL
DSPI_1
eMIOS_0
—
ADC_0
I/O
O
I/O
—
I
J
Tristate
66
88
106
L14
Port E
MPC5607B Microcontroller Data Sheet, Rev. 8
22
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PE[0]
PCR[64] AF0
AF1
AF2
AF3
—
—
GPIO[64]
E0UC[16]
—
—
WKPU[6]5
CAN5RX
SIUL
eMIOS_0
—
—
WKPU
FlexCAN_5
I/O
I/O
—
—
I
I
S
Tristate
6
10
18
F1
PE[1]
PCR[65] AF0
AF1
AF2
AF3
GPIO[65]
E0UC[17]
CAN5TX
—
SIUL
I/O
eMIOS_0 I/O
FlexCAN_5 O
—
—
M
Tristate
8
12
20
F4
PE[2]
PCR[66] AF0
AF1
AF2
AF3
—
—
GPIO[66]
E0UC[18]
—
—
EIRQ[21]
SIN_1
SIUL
eMIOS_0
—
—
SIUL
DSPI_1
I/O
I/O
—
—
I
I
M
Tristate
89
128
156
D7
PE[3]
PCR[67] AF0
AF1
AF2
AF3
GPIO[67]
E0UC[19]
SOUT_1
—
SIUL
eMIOS_0
DSPI_1
—
I/O
I/O
O
—
M
Tristate
90
129
157
C7
PE[4]
PCR[68] AF0
AF1
AF2
AF3
—
GPIO[68]
E0UC[20]
SCK_1
—
EIRQ[9]
SIUL
eMIOS_0
DSPI_1
—
SIUL
I/O
I/O
I/O
—
I
M
Tristate
93
132
160
D6
PE[5]
PCR[69] AF0
AF1
AF2
AF3
GPIO[69]
E0UC[21]
CS0_1
MA[2]
SIUL
eMIOS_0
DSPI_1
ADC_0
I/O
I/O
I/O
O
M
Tristate
94
133
161
C6
PE[6]
PCR[70] AF0
AF1
AF2
AF3
—
GPIO[70]
E0UC[22]
CS3_0
MA[1]
EIRQ[22]
SIUL
eMIOS_0
DSPI_0
ADC_0
SIUL
I/O
I/O
O
O
I
M
Tristate
95
139
167
B5
PE[7]
PCR[71] AF0
AF1
AF2
AF3
—
GPIO[71]
E0UC[23]
CS2_0
MA[0]
EIRQ[23]
SIUL
eMIOS_0
DSPI_0
ADC_0
SIUL
I/O
I/O
O
O
I
M
Tristate
96
140
168
C4
PE[8]
PCR[72] AF0
AF1
AF2
AF3
GPIO[72]
CAN2TX
E0UC[22]
CAN3TX
SIUL
I/O
FlexCAN_2 O
eMIOS_0 I/O
FlexCAN_3 O
M
Tristate
9
13
21
G2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
23
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PE[9]
PCR[73] AF0
AF1
AF2
AF3
—
—
—
GPIO[73]
—
E0UC[23]
—
WKPU[7]5
CAN2RX
CAN3RX
SIUL
—
eMIOS_0
—
WKPU
FlexCAN_2
FlexCAN_3
I/O
—
I/O
—
I
I
I
S
Tristate
10
14
22
G1
PE[10]
PCR[74] AF0
AF1
AF2
AF3
—
GPIO[74]
LIN3TX
CS3_1
E1UC[30]
EIRQ[10]
SIUL
LINFlex_3
DSPI_1
eMIOS_1
SIUL
I/O
O
O
I/O
I
S
Tristate
11
15
23
G3
PE[11]
PCR[75] AF0
AF1
AF2
AF3
—
—
GPIO[75]
E0UC[24]
CS4_1
—
LIN3RX
WKPU[14]5
SIUL
eMIOS_0
DSPI_1
—
LINFlex_3
WKPU
I/O
I/O
O
—
I
I
S
Tristate
13
17
25
H2
PE[12]
PCR[76] AF0
AF1
AF2
AF3
—
—
—
GPIO[76]
—
E1UC[19]12
—
EIRQ[11]
SIN_2
ADC1_S[7]
SIUL
—
eMIOS_1
—
SIUL
DSPI_2
ADC_1
I/O
—
I/O
—
I
I
I
J
Tristate
76
109
133
C14
PE[13]
PCR[77] AF0
AF1
AF2
AF3
GPIO[77]
SOUT_2
E1UC[20]
—
SIUL
DSPI_2
eMIOS_1
—
I/O
O
I/O
—
S
Tristate
—
103
127
D15
PE[14]
PCR[78] AF0
AF1
AF2
AF3
—
GPIO[78]
SCK_2
E1UC[21]
—
EIRQ[12]
SIUL
DSPI_2
eMIOS_1
—
SIUL
I/O
I/O
I/O
—
I
S
Tristate
—
112
136
C13
PE[15]
PCR[79] AF0
AF1
AF2
AF3
GPIO[79]
CS0_2
E1UC[22]
—
SIUL
DSPI_2
eMIOS_1
—
I/O
I/O
I/O
—
M
Tristate
—
113
137
A13
Port F
MPC5607B Microcontroller Data Sheet, Rev. 8
24
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PF[0]
PCR[80] AF0
AF1
AF2
AF3
—
GPIO[80]
E0UC[10]
CS3_1
—
ADC0_S[8]
SIUL
eMIOS_0
DSPI_1
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
55
63
N10
PF[1]
PCR[81] AF0
AF1
AF2
AF3
—
GPIO[81]
E0UC[11]
CS4_1
—
ADC0_S[9]
SIUL
eMIOS_0
DSPI_1
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
56
64
P10
PF[2]
PCR[82] AF0
AF1
AF2
AF3
—
GPIO[82]
E0UC[12]
CS0_2
—
ADC0_S[10]
SIUL
eMIOS_0
DSPI_2
—
ADC_0
I/O
I/O
I/O
—
I
J
Tristate
—
57
65
T10
PF[3]
PCR[83] AF0
AF1
AF2
AF3
—
GPIO[83]
E0UC[13]
CS1_2
—
ADC0_S[11]
SIUL
eMIOS_0
DSPI_2
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
58
66
R10
PF[4]
PCR[84] AF0
AF1
AF2
AF3
—
GPIO[84]
E0UC[14]
CS2_2
—
ADC0_S[12]
SIUL
eMIOS_0
DSPI_2
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
59
67
N11
PF[5]
PCR[85] AF0
AF1
AF2
AF3
—
GPIO[85]
E0UC[22]
CS3_2
—
ADC0_S[13]
SIUL
eMIOS_0
DSPI_2
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
60
68
P11
PF[6]
PCR[86] AF0
AF1
AF2
AF3
—
GPIO[86]
E0UC[23]
CS1_1
—
ADC0_S[14]
SIUL
eMIOS_0
DSPI_1
—
ADC_0
I/O
I/O
O
—
I
J
Tristate
—
61
69
T11
PF[7]
PCR[87] AF0
AF1
AF2
AF3
—
GPIO[87]
—
CS2_1
—
ADC0_S[15]
SIUL
—
DSPI_1
—
ADC_0
I/O
—
O
—
I
J
Tristate
—
62
70
R11
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
25
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PF[8]
PCR[88] AF0
AF1
AF2
AF3
GPIO[88]
CAN3TX
CS4_0
CAN2TX
SIUL
I/O
FlexCAN_3 O
DSPI_0
O
FlexCAN_2 O
M
Tristate
—
34
42
P1
PF[9]
PCR[89] AF0
AF1
AF2
AF3
—
—
—
GPIO[89]
E1UC[1]
CS5_0
—
WKPU[22]5
CAN2RX
CAN3RX
SIUL
I/O
eMIOS_1 I/O
DSPI_0
O
—
—
WKPU
I
FlexCAN_2 I
FlexCAN_3 I
S
Tristate
—
33
41
N2
PF[10]
PCR[90] AF0
AF1
AF2
AF3
GPIO[90]
CS1_0
LIN4TX
E1UC[2]
SIUL
DSPI_0
LINFlex_4
eMIOS_1
I/O
O
O
I/O
M
Tristate
—
38
46
R3
PF[11]
PCR[91] AF0
AF1
AF2
AF3
—
—
GPIO[91]
CS2_0
E1UC[3]
—
WKPU[15]5
LIN4RX
SIUL
DSPI_0
eMIOS_1
—
WKPU
LINFlex_4
I/O
O
I/O
—
I
I
S
Tristate
—
39
47
R4
PF[12]
PCR[92] AF0
AF1
AF2
AF3
GPIO[92]
E1UC[25]
LIN5TX
—
SIUL
eMIOS_1
LINFlex_5
—
I/O
I/O
O
—
M
Tristate
—
35
43
R1
PF[13]
PCR[93] AF0
AF1
AF2
AF3
—
—
GPIO[93]
E1UC[26]
—
—
WKPU[16]5
LIN5RX
SIUL
eMIOS_1
—
—
WKPU
LINFlex_5
I/O
I/O
—
—
I
I
S
Tristate
—
41
49
T6
PF[14]
PCR[94] AF0
AF1
AF2
AF3
GPIO[94]
CAN4TX
E1UC[27]
CAN1TX
SIUL
I/O
FlexCAN_4 O
eMIOS_1 I/O
FlexCAN_1 O
M
Tristate
—
102
126
D14
PF[15]
PCR[95] AF0
AF1
AF2
AF3
—
—
—
GPIO[95]
E1UC[4]
—
—
EIRQ[13]
CAN1RX
CAN4RX
SIUL
eMIOS_1
—
—
SIUL
FlexCAN_1
FlexCAN_4
S
Tristate
—
101
125
E15
I/O
I/O
—
—
I
I
I
Port G
MPC5607B Microcontroller Data Sheet, Rev. 8
26
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PG[0]
PCR[96] AF0
AF1
AF2
AF3
GPIO[96]
CAN5TX
E1UC[23]
—
SIUL
I/O
FlexCAN_5 O
eMIOS_1 I/O
—
—
M
Tristate
—
98
122
E14
PG[1]
PCR[97] AF0
AF1
AF2
AF3
—
—
GPIO[97]
—
E1UC[24]
—
EIRQ[14]
CAN5RX
SIUL
—
eMIOS_1
—
SIUL
FlexCAN_5
I/O
—
I/O
—
I
I
S
Tristate
—
97
121
E13
PG[2]
PCR[98] AF0
AF1
AF2
AF3
GPIO[98]
E1UC[11]
SOUT_3
—
SIUL
eMIOS_1
DSPI_3
—
I/O
I/O
O
—
M
Tristate
—
8
16
E4
PG[3]
PCR[99] AF0
AF1
AF2
AF3
—
GPIO[99]
E1UC[12]
CS0_3
—
WKPU[17]5
SIUL
eMIOS_1
DSPI_3
—
WKPU
I/O
I/O
I/O
—
I
S
Tristate
—
7
15
E3
PG[4]
PCR[100] AF0
AF1
AF2
AF3
GPIO[100]
E1UC[13]
SCK_3
—
SIUL
eMIOS_1
DSPI_3
—
I/O
I/O
I/O
—
M
Tristate
—
6
14
E1
PG[5]
PCR[101] AF0
AF1
AF2
AF3
—
—
GPIO[101]
E1UC[14]
—
—
WKPU[18]5
SIN_3
SIUL
eMIOS_1
—
—
WKPU
DSPI_3
I/O
I/O
—
—
I
I
S
Tristate
—
5
13
E2
PG[6]
PCR[102] AF0
AF1
AF2
AF3
GPIO[102]
E1UC[15]
LIN6TX
—
SIUL
eMIOS_1
LINFlex_6
—
I/O
I/O
O
—
M
Tristate
—
30
38
M2
PG[7]
PCR[103] AF0
AF1
AF2
AF3
—
—
GPIO[103]
E1UC[16]
E1UC[30]
—
WKPU[20]5
LIN6RX
SIUL
eMIOS_1
eMIOS_1
—
WKPU
LINFlex_6
I/O
I/O
I/O
—
I
I
S
Tristate
—
29
37
M1
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
27
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PG[8]
PCR[104] AF0
AF1
AF2
AF3
—
GPIO[104]
E1UC[17]
LIN7TX
CS0_2
EIRQ[15]
SIUL
eMIOS_1
LINFlex_7
DSPI_2
SIUL
I/O
I/O
O
I/O
I
S
Tristate
—
26
34
L2
PG[9]
PCR[105] AF0
AF1
AF2
AF3
—
—
GPIO[105]
E1UC[18]
—
SCK_2
WKPU[21]5
LIN7RX
SIUL
eMIOS_1
—
DSPI_2
WKPU
LINFlex_7
I/O
I/O
—
I/O
I
I
S
Tristate
—
25
33
L1
PG[10] PCR[106] AF0
AF1
AF2
AF3
—
GPIO[106]
E0UC[24]
E1UC[31]
—
SIN_4
SIUL
eMIOS_0
eMIOS_1
—
DSPI_4
I/O
I/O
I/O
—
I
S
Tristate
—
114
138
D13
PG[11] PCR[107] AF0
AF1
AF2
AF3
GPIO[107]
E0UC[25]
CS0_4
—
SIUL
eMIOS_0
DSPI_4
—
I/O
I/O
I/O
—
M
Tristate
—
115
139
B12
PG[12] PCR[108] AF0
AF1
AF2
AF3
GPIO[108]
E0UC[26]
SOUT_4
—
SIUL
eMIOS_0
DSPI_4
—
I/O
I/O
O
—
M
Tristate
—
92
116
K14
PG[13] PCR[109] AF0
AF1
AF2
AF3
GPIO[109]
E0UC[27]
SCK_4
—
SIUL
eMIOS_0
DSPI_4
—
I/O
I/O
I/O
—
M
Tristate
—
91
115
K16
PG[14] PCR[110] AF0
AF1
AF2
AF3
GPIO[110]
E1UC[0]
LIN8TX
—
SIUL
eMIOS_1
LINFlex_8
—
I/O
I/O
O
—
S
Tristate
—
110
134
B14
PG[15] PCR[111] AF0
AF1
AF2
AF3
—
GPIO[111]
E1UC[1]
—
—
LIN8RX
SIUL
eMIOS_1
—
—
LINFlex_8
I/O
I/O
—
—
I
M
Tristate
—
111
135
B13
M
Tristate
—
93
117
F13
Port H
PH[0]
PCR[112] AF0
AF1
AF2
AF3
—
GPIO[112]
E1UC[2]
—
—
SIN_1
SIUL
eMIOS_1
—
—
DSPI_1
I/O
I/O
—
—
I
MPC5607B Microcontroller Data Sheet, Rev. 8
28
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PH[1]
PCR[113] AF0
AF1
AF2
AF3
GPIO[113]
E1UC[3]
SOUT_1
—
SIUL
eMIOS_1
DSPI_1
—
I/O
I/O
O
—
M
Tristate
—
94
118
F14
PH[2]
PCR[114] AF0
AF1
AF2
AF3
GPIO[114]
E1UC[4]
SCK_1
—
SIUL
eMIOS_1
DSPI_1
—
I/O
I/O
I/O
—
M
Tristate
—
95
119
F16
PH[3]
PCR[115] AF0
AF1
AF2
AF3
GPIO[115]
E1UC[5]
CS0_1
—
SIUL
eMIOS_1
DSPI_1
—
I/O
I/O
I/O
—
M
Tristate
—
96
120
F15
PH[4]
PCR[116] AF0
AF1
AF2
AF3
GPIO[116]
E1UC[6]
—
—
SIUL
eMIOS_1
—
—
I/O
I/O
—
—
M
Tristate
—
134
162
A6
PH[5]
PCR[117] AF0
AF1
AF2
AF3
GPIO[117]
E1UC[7]
—
—
SIUL
eMIOS_1
—
—
I/O
I/O
—
—
S
Tristate
—
135
163
B6
PH[6]
PCR[118] AF0
AF1
AF2
AF3
GPIO[118]
E1UC[8]
—
MA[2]
SIUL
eMIOS_1
—
ADC_0
I/O
I/O
—
O
M
Tristate
—
136
164
D5
PH[7]
PCR[119] AF0
AF1
AF2
AF3
GPIO[119]
E1UC[9]
CS3_2
MA[1]
SIUL
eMIOS_1
DSPI_2
ADC_0
I/O
I/O
O
O
M
Tristate
—
137
165
C5
PH[8]
PCR[120] AF0
AF1
AF2
AF3
GPIO[120]
E1UC[10]
CS2_2
MA[0]
SIUL
eMIOS_1
DSPI_2
ADC_0
I/O
I/O
O
O
M
Tristate
—
138
166
A5
PH[9]10 PCR[121] AF0
AF1
AF2
AF3
GPIO[121]
—
TCK
—
SIUL
—
JTAGC
—
I/O
—
I
—
S
Input,
weak
pull-up
88
127
155
B8
PH[10]10 PCR[122] AF0
AF1
AF2
AF3
GPIO[122]
—
TMS
—
SIUL
—
JTAGC
—
I/O
—
I
—
M
Input,
weak
pull-up
81
120
148
B9
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
29
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PH[11] PCR[123] AF0
AF1
AF2
AF3
GPIO[123]
SOUT_3
CS0_4
E1UC[5]
SIUL
DSPI_3
DSPI_4
eMIOS_1
I/O
O
I/O
I/O
M
Tristate
—
—
140
A14
PH[12] PCR[124] AF0
AF1
AF2
AF3
GPIO[124]
SCK_3
CS1_4
E1UC[25]
SIUL
DSPI_3
DSPI_4
eMIOS_1
I/O
I/O
O
I/O
M
Tristate
—
—
141
D12
PH[13] PCR[125] AF0
AF1
AF2
AF3
GPIO[125]
SOUT_4
CS0_3
E1UC[26]
SIUL
DSPI_4
DSPI_3
eMIOS_1
I/O
O
I/O
I/O
M
Tristate
—
—
9
B3
PH[14] PCR[126] AF0
AF1
AF2
AF3
GPIO[126]
SCK_4
CS1_3
E1UC[27]
SIUL
DSPI_4
DSPI_3
eMIOS_1
I/O
I/O
O
I/O
M
Tristate
—
—
10
D1
PH[15] PCR[127] AF0
AF1
AF2
AF3
GPIO[127]
SOUT_5
—
E1UC[17]
SIUL
DSPI_5
—
eMIOS_1
I/O
O
—
I/O
M
Tristate
—
—
8
A3
Port I
PI[0]
PCR[128] AF0
AF1
AF2
AF3
GPIO[128]
E0UC[28]
LIN8TX
—
SIUL
eMIOS_0
LINFlex_8
—
I/O
I/O
O
—
S
Tristate
—
—
172
A9
PI[1]
PCR[129] AF0
AF1
AF2
AF3
—
—
GPIO[129]
E0UC[29]
—
—
WKPU[24]5
LIN8RX
SIUL
eMIOS_0
—
—
WKPU
LINFlex_8
I/O
I/O
—
—
I
I
S
Tristate
—
—
171
A10
PI[2]
PCR[130] AF0
AF1
AF2
AF3
GPIO[130]
E0UC[30]
LIN9TX
—
SIUL
eMIOS_0
LINFlex_9
—
I/O
I/O
O
—
S
Tristate
—
—
170
B10
PI[3]
PCR[131] AF0
AF1
AF2
AF3
—
—
GPIO[131]
E0UC[31]
—
—
WKPU[23]5
LIN9RX
SIUL
eMIOS_0
—
—
WKPU
LINFlex_9
I/O
I/O
—
—
I
I
S
Tristate
—
—
169
C10
MPC5607B Microcontroller Data Sheet, Rev. 8
30
Freescale Semiconductor
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PI[4]
PCR[132] AF0
AF1
AF2
AF3
GPIO[132]
E1UC[28]
SOUT_4
—
SIUL
eMIOS_1
DSPI_4
—
I/O
I/O
O
—
S
Tristate
—
—
143
A12
PI[5]
PCR[133] AF0
AF1
AF2
AF3
GPIO[133]
E1UC[29]
SCK_4
—
SIUL
eMIOS_1
DSPI_4
—
I/O
I/O
I/O
—
S
Tristate
—
—
142
C12
PI[6]
PCR[134] AF0
AF1
AF2
AF3
GPIO[134]
E1UC[30]
CS0_4
—
SIUL
eMIOS_1
DSPI_4
—
I/O
I/O
I/O
—
S
Tristate
—
—
11
D2
PI[7]
PCR[135] AF0
AF1
AF2
AF3
GPIO[135]
E1UC[31]
CS1_4
—
SIUL
eMIOS_1
DSPI_4
—
I/O
I/O
O
—
S
Tristate
—
—
12
D3
PI[8]
PCR[136] AF0
AF1
AF2
AF3
—
GPIO[136]
—
—
—
ADC0_S[16]
SIUL
—
—
—
ADC_0
I/O
—
—
—
I
J
Tristate
—
—
108
J13
PI[9]
PCR[137] AF0
AF1
AF2
AF3
—
GPIO[137]
—
—
—
ADC0_S[17]
SIUL
—
—
—
ADC_0
I/O
—
—
—
I
J
Tristate
—
—
109
J14
PI[10]
PCR[138] AF0
AF1
AF2
AF3
—
GPIO[138]
—
—
—
ADC0_S[18]
SIUL
—
—
—
ADC_0
I/O
—
—
—
I
J
Tristate
—
—
110
J15
PI[11]
PCR[139] AF0
AF1
AF2
AF3
—
—
GPIO[139]
—
—
—
ADC0_S[19]
SIN_3
SIUL
—
—
—
ADC_0
DSPI_3
I/O
—
—
—
I
I
J
Tristate
—
—
111
J16
PI[12]
PCR[140] AF0
AF1
AF2
AF3
—
GPIO[140]
CS0_3
—
—
ADC0_S[20]
SIUL
DSPI_3
—
—
ADC_0
I/O
I/O
—
—
I
J
Tristate
—
—
112
G14
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
31
Package pinouts and signal descriptions
Peripheral
RESET
configuration3
Function
Pad type
PCR
I/O direction2
Port pin
Alternate function1
Table 5. Functional port pin descriptions (continued)
Pin number
100
LQFP
144
LQFP
176
LQFP
208
MAP
BGA
4
PI[13]
PCR[141] AF0
AF1
AF2
AF3
—
GPIO[141]
CS1_3
—
—
ADC0_S[21]
SIUL
DSPI_3
—
—
ADC_0
I/O
O
—
—
I
J
Tristate
—
—
113
G15
PI[14]
PCR[142] AF0
AF1
AF2
AF3
—
—
GPIO[142]
—
—
—
ADC0_S[22]
SIN_4
SIUL
—
—
—
ADC_0
DSPI_4
I/O
—
—
—
I
I
J
Tristate
—
—
76
R8
PI[15]
PCR[143] AF0
AF1
AF2
AF3
—
GPIO[143]
CS0_4
—
—
ADC0_S[23]
SIUL
DSPI_4
—
—
ADC_0
I/O
I/O
—
—
I
J
Tristate
—
—
75
T8
Port J
PJ[0]
PCR[144] AF0
AF1
AF2
AF3
—
GPIO[144]
CS1_4
—
—
ADC0_S[24]
SIUL
DSPI_4
—
—
ADC_0
I/O
O
—
—
I
J
Tristate
—
—
74
N5
PJ[1]
PCR[145] AF0
AF1
AF2
AF3
—
—
GPIO[145]
—
—
—
ADC0_S[25]
SIN_5
SIUL
—
—
——
ADC_0
DSPI_5
I/O
—
—
—
I
I
J
Tristate
—
—
73
P5
PJ[2]
PCR[146] AF0
AF1
AF2
AF3
—
GPIO[146]
CS0_5
—
—
ADC0_S[26]
SIUL
DSPI_5
—
—
ADC_0
I/O
I/O
—
—
I
J
Tristate
—
—
72
P4
PJ[3]
PCR[147] AF0
AF1
AF2
AF3
—
GPIO[147]
CS1_5
—
—
ADC0_S[27]
SIUL
DSPI_5
—
—
ADC_0
I/O
O
—
—
I
J
Tristate
—
—
71
P2
PJ[4]
PCR[148] AF0
AF1
AF2
AF3
GPIO[148]
SCK_5
E1UC[18]
—
SIUL
DSPI_5
eMIOS_1
—
I/O
I/O
I/O
—
M
Tristate
—
—
5
A4
MPC5607B Microcontroller Data Sheet, Rev. 8
32
Freescale Semiconductor
Package pinouts and signal descriptions
1
Alternate functions are chosen by setting the values of the PCR.PA bitfields inside the SIUL module.
PCR.PA = 00  AF0; PCR.PA = 01  AF1; PCR.PA = 10  AF2; PCR.PA = 11  AF2. This is intended to
select the output functions; to use one of the input functions, the PCR.IBE bit must be written to ‘1’, regardless of
the values selected in the PCR.PA bitfields. For this reason, the value corresponding to an input only function is
reported as “—”.
2
Multiple inputs are routed to all respective modules internally. The input of some modules must be configured by
setting the values of the PSMIO.PADSELx bitfields inside the SIUL module.
3
The RESET configuration applies during and after reset.
4
208 MAPBGA available only as development package for Nexus2+
5
All WKPU pins also support external interrupt capability. See the WKPU chapter for further details.
6
NMI has higher priority than alternate function. When NMI is selected, the PCR.AF field is ignored.
7
“Not applicable” because these functions are available only while the device is booting. Refer to the BAM
information for details.
8
Value of PCR.IBE bit must be 0
9
This wakeup input cannot be used to exit STANDBY mode.
10 Out of reset all the functional pins except PC[0:1] and PH[9:10] are available to the user as GPIO.
PC[0:1] are available as JTAG pins (TDI and TDO respectively).
PH[9:10] are available as JTAG pins (TCK and TMS respectively).
It is up to the user to configure these pins as GPIO when needed.
11 PC[1] is a fast/medium pad but is in medium configuration by default. This pad is in Alternate Function 2 mode after
reset which has TDO functionality. The reset value of PCR.OBE is ‘1’, but this setting has no impact as long as this
pad stays in AF2 mode. After configuring this pad as GPIO (PCR.PA = 0), output buffer is enabled as reset value
of PCR.OBE = 1.
12 Not available in 100 LQFP package
3.8
Nexus 2+ pins
In the 208 MAPBGA package, eight additional debug pins are available (see Table 6).
Table 6. Nexus 2+ pin descriptions
Pin number
1
Port pin
Function
I/O
direction
MCKO
Message clock out
O
F
MDO0
Message data out 0
O
MDO1
Message data out 1
MDO2
Pad type
Function
after reset
100
LQFP
144
LQFP
208 MAP
BGA1
—
—
—
T4
M
—
—
—
H15
O
M
—
—
—
H16
Message data out 2
O
M
—
—
—
H14
MDO3
Message data out 3
O
M
—
—
—
H13
EVTI
Event in
I
M
Pull-up
—
—
K1
EVTO
Event out
O
M
—
—
—
L4
MSEO
Message start/end out
O
M
—
—
—
G16
208 MAPBGA available only as development package for Nexus2+
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
33
Electrical characteristics
4
Electrical characteristics
This section contains electrical characteristics of the device as well as temperature and power considerations.
This product contains devices to protect the inputs against damage due to high static voltages. However, it is advisable to take
precautions to avoid application of any voltage higher than the specified maximum rated voltages.
To enhance reliability, unused inputs can be driven to an appropriate logic voltage level (VDD or VSS). This could be done by
the internal pull-up and pull-down, which is provided by the product for most general purpose pins.
The parameters listed in the following tables represent the characteristics of the device and its demands on the system.
In the tables where the device logic provides signals with their respective timing characteristics, the symbol “CC” for Controller
Characteristics is included in the Symbol column.
In the tables where the external system must provide signals with their respective timing characteristics to the device, the symbol
“SR” for System Requirement is included in the Symbol column.
4.1
Parameter classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better
understanding, the classifications listed in Table 7 are used and the parameters are tagged accordingly in the tables where
appropriate.
Table 7. Parameter classifications
Classification tag
Tag description
P
Those parameters are guaranteed during production testing on each individual device.
C
Those parameters are achieved by the design characterization by measuring a statistically
relevant sample size across process variations.
T
Those parameters are achieved by design characterization on a small sample size from typical
devices under typical conditions unless otherwise noted. All values shown in the typical column
are within this category.
D
Those parameters are derived mainly from simulations.
NOTE
The classification is shown in the column labeled “C” in the parameter tables where
appropriate.
4.2
NVUSRO register
Bit values in the Non-Volatile User Options (NVUSRO) Register control portions of the device configuration, namely electrical
parameters such as high voltage supply and oscillator margin, as well as digital functionality (watchdog enable/disable after
reset).
For a detailed description of the NVUSRO register, please refer to the device reference manual.
4.2.1
NVUSRO[PAD3V5V] field description
The DC electrical characteristics are dependent on the PAD3V5V bit value. Table 8 shows how NVUSRO[PAD3V5V] controls
the device configuration.
MPC5607B Microcontroller Data Sheet, Rev. 8
34
Freescale Semiconductor
Electrical characteristics
Table 8. PAD3V5V field description1
Value2
1
0
High voltage supply is 5.0 V
1
High voltage supply is 3.3 V
See the device reference manual for more information on the NVUSRO register.
Default manufacturing value is ‘1’. Value can be programmed by customer in Shadow Flash.
2
4.2.2
Description
NVUSRO[OSCILLATOR_MARGIN] field description
The fast external crystal oscillator consumption is dependent on the OSCILLATOR_MARGIN bit value. Table 9 shows how
NVUSRO[OSCILLATOR_MARGIN] controls the device configuration.
Table 9. OSCILLATOR_MARGIN field description1
Value2
1
0
Low consumption configuration (4 MHz/8 MHz)
1
High margin configuration (4 MHz/16 MHz)
See the device reference manual for more information on the NVUSRO register.
Default manufacturing value is ‘1’. Value can be programmed by customer in Shadow Flash.
2
4.2.3
Description
NVUSRO[WATCHDOG_EN] field description
The watchdog enable/disable configuration after reset is dependent on the WATCHDOG_EN bit value. Table 10 shows how
NVUSRO[WATCHDOG_EN] controls the device configuration.
Table 10. WATCHDOG_EN field description
Value1
1
4.3
Description
0
Disable after reset
1
Enable after reset
Default manufacturing value is ‘1’. Value can be programmed by customer in Shadow Flash.
Absolute maximum ratings
Table 11. Absolute maximum ratings
Value
Symbol
Parameter
Conditions
Unit
Min
Max
VSS
SR Digital ground on VSS_HV pins
—
0
0
V
VDD
SR Voltage on VDD_HV pins with respect to
ground (VSS)
—
–0.3
6.0
V
VSS_LV
SR Voltage on VSS_LV (low voltage digital supply)
pins with respect to ground (VSS)
—
VDD_BV
SR Voltage on VDD_BV (regulator supply) pin with
respect to ground (VSS)
—
Relative to VDD
VSS – 0.1 VSS + 0.1
–0.3
6.0
–0.3
VDD + 0.3
V
V
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
35
Electrical characteristics
Table 11. Absolute maximum ratings (continued)
Value
Symbol
Parameter
Conditions
Unit
Min
—
VSS_ADC SR Voltage on VSS_HV_ADC0, VSS_HV_ADC1
(ADC reference) pins with respect to ground
(VSS)
VDD_ADC SR Voltage on VDD_HV_ADC0, VDD_HV_ADC1
—
(ADC reference) pins with respect to ground
Relative to VDD
(VSS)
VIN
SR Voltage on any GPIO pin with respect to
ground (VSS)
Max
VSS – 0.1 VSS + 0.1
–0.3
6.0
V
VDD  0.3 VDD + 0.3
—
–0.3
6.0
—
VDD + 0.3
Relative to VDD
IINJPAD
SR Injected input current on any pin during
overload condition
—
–10
10
IINJSUM
SR Absolute sum of all injected input currents
during overload condition
—
–50
50
IAVGSEG
SR Sum of all the static I/O current within a supply VDD = 5.0 V ± 10%,
segment
PAD3V5V = 0
—
70
VDD = 3.3 V ± 10%,
PAD3V5V = 1
—
64
–55
150
TSTORAGE SR Storage temperature
V
—
V
mA
mA
°C
NOTE
Stresses exceeding the recommended absolute maximum ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operational sections of this
specification are not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. During overload conditions (VIN > VDD or
VIN < VSS), the voltage on pins with respect to ground (VSS) must not exceed the
recommended values.
4.4
Recommended operating conditions
Table 12. Recommended operating conditions (3.3 V)
Value
Symbol
VSS
Parameter
Conditions
Unit
Min
Max
SR Digital ground on VSS_HV pins
—
0
0
V
SR Voltage on VDD_HV pins with respect to
ground (VSS)
—
3.0
3.6
V
VSS_LV2
SR Voltage on VSS_LV (low voltage digital
supply) pins with respect to ground (VSS)
—
VSS  0.1
VSS + 0.1
V
VDD_BV3
SR Voltage on VDD_BV pin (regulator supply)
with respect to ground (VSS)
—
3.0
3.6
V
VDD  0.1
VDD + 0.1
VDD
1
Relative to VDD
MPC5607B Microcontroller Data Sheet, Rev. 8
36
Freescale Semiconductor
Electrical characteristics
Table 12. Recommended operating conditions (3.3 V) (continued)
Value
Symbol
3
4
5
6
7
Unit
Min
Max
SR Voltage on VSS_HV_ADC0,
VSS_HV_ADC1 (ADC reference) pin with
respect to ground (VSS)
—
VSS  0.1
VSS + 0.1
V
VDD_ADC4
SR Voltage on VDD_HV_ADC0,
VDD_HV_ADC1 (ADC reference) with
respect to ground (VSS)
—
3.05
3.6
V
VDD  0.1
VDD + 0.1
VSS  0.1
—
—
VDD + 0.1
SR Voltage on any GPIO pin with respect to
ground (VSS)
Relative to VDD
—
Relative to VDD
V
IINJPAD
SR Injected input current on any pin during
overload condition
—
5
5
IINJSUM
SR Absolute sum of all injected input currents
during overload condition
—
50
50
SR VDD slope to ensure correct power up6
—
—
0.25
V/µs
40
85
°C
40
110
40
105
40
130
40
125
40
150
TVDD
2
Conditions
VSS_ADC
VIN
1
Parameter
fCPU  64 MHz7
TA C-Grade Part
SR Ambient temperature under bias
TJ C-Grade Part
SR Junction temperature under bias
—
TA V-Grade Part
SR Ambient temperature under bias
fCPU  64
TJ V-Grade Part
SR Junction temperature under bias
—
TA M-Grade Part
SR Ambient temperature under bias
TJ M-Grade Part
SR Junction temperature under bias
MHz7
fCPU  64 MHz7
—
mA
100 nF capacitance needs to be provided between each VDD/VSS pair.
330 nF capacitance needs to be provided between each VDD_LV/VSS_LV supply pair.
470 nF capacitance needs to be provided between VDD_BV and the nearest VSS_LV (higher value may be needed
depending on external regulator characteristics). Supply ramp slope on VDD_BV should always be faster or equal
to slope of VDD_HV. Otherwise, device may enter regulator bypass mode if slope on VDD_BV is slower.
100 nF capacitance needs to be provided between VDD_ADC/VSS_ADC pair.
Full electrical specification cannot be guaranteed when voltage drops below 3.0 V. In particular, ADC electrical
characteristics and I/Os DC electrical specification may not be guaranteed. When voltage drops below VLVDHVL,
device is reset.
Guaranteed by device validation
When the FMPLL uses the frequency modulation with a modulation depth of 4% from the center spread frequency,
the maximum value of fCPU is 66.56 MHz.
Table 13. Recommended operating conditions (5.0 V)
Value
Symbol
VSS
VDD
1
Parameter
Conditions
Unit
Min
Max
SR Digital ground on VSS_HV pins
—
0
0
V
SR Voltage on VDD_HV pins with respect to ground
(VSS)
—
4.5
5.5
V
3.0
5.5
Voltage drop2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
37
Electrical characteristics
Table 13. Recommended operating conditions (5.0 V) (continued)
Value
Symbol
Parameter
Conditions
Unit
Min
Max
VSS  0.1
VSS + 0.1
V
4.5
5.5
V
Voltage drop
3.0
5.5
Relative to VDD
3.0
VDD + 0.1
VSS  0.1
VSS + 0.1
V
4.5
5.5
V
3.0
5.5
VSS_LV3
SR Voltage on VSS_LV (low voltage digital supply)
pins with respect to ground (VSS)
—
VDD_BV4
SR Voltage on VDD_BV pin (regulator supply) with
respect to ground (VSS)
—
2
VSS_ADC
SR Voltage on VSS_HV_ADC0, VSS_HV_ADC1
(ADC reference) pin with respect to ground (VSS)
—
VDD_ADC5
SR Voltage on VDD_HV_ADC0, VDD_HV_ADC1
(ADC reference) with respect to ground (VSS)
—
2
Voltage drop
Relative to VDD VDD  0.1 VDD + 0.1
VIN
SR Voltage on any GPIO pin with respect to ground
(VSS)
—
VSS  0.1
—
Relative to VDD
—
VDD + 0.1
V
IINJPAD
SR Injected input current on any pin during overload
condition
—
5
5
IINJSUM
SR Absolute sum of all injected input currents during
overload condition
—
50
50
SR VDD slope to ensure correct power up6
—
—
0.25
V/µs
TA C-Grade Part SR Ambient temperature under bias
fCPU  64 MHz7
40
85
°C
TJ C-Grade Part SR Junction temperature under bias
—
40
110
TA V-Grade Part SR Ambient temperature under bias
fCPU  64
40
105
TJ V-Grade Part SR Junction temperature under bias
—
40
130
TA M-Grade Part SR Ambient temperature under bias
fCPU  64
40
125
TJ M-Grade Part SR Junction temperature under bias
—
40
150
TVDD
1
2
3
4
5
6
7
MHz7
MHz7
mA
100 nF capacitance needs to be provided between each VDD/VSS pair.
Full device operation is guaranteed by design when the voltage drops below 4.5 V down to 3.0 V. However, certain
analog electrical characteristics will not be guaranteed to stay within the stated limits.
330 nF capacitance needs to be provided between each VDD_LV/VSS_LV supply pair.
470 nF capacitance needs to be provided between VDD_BV and the nearest VSS_LV (higher value may be needed
depending on external regulator characteristics). While the supply voltage ramps up, the slope on VDD_BV should
be less than 0.9VDD_HV in order to ensure the device does not enter regulator bypass mode.
100 nF capacitance needs to be provided between VDD_ADC/VSS_ADC pair.
Guaranteed by device validation
When the FMPLL uses the frequency modulation with a modulation depth of 4% from the center spread frequency,
the maximum value of fCPU is 66.56 MHz.
NOTE
RAM data retention is guaranteed with VDD_LV not below 1.08 V.
MPC5607B Microcontroller Data Sheet, Rev. 8
38
Freescale Semiconductor
Electrical characteristics
4.5
Thermal characteristics
4.5.1
External ballast resistor recommendations
External ballast resistor on VDD_BV pin helps in reducing the overall power dissipation inside the device. This resistor is
required only when maximum power consumption exceeds the limit imposed by package thermal characteristics.
As stated in Table 14 LQFP thermal characteristics, considering a thermal resistance of 144 LQFP as 48.3 °C/W, at ambient
temperature TA = 125 °C, the junction temperature Tj will cross 150 °C if the total power dissipation is greater than
(150 – 125)/48.3 = 517 mW. Therefore, the total device current IDDMAX at 125 °C/5.5 V must not exceed 94.1 mA (i.e.,
PD/VDD). Assuming an average IDD(VDD_HV) of 15–20 mA consumption typically during device RUN mode, the LV domain
consumption IDD(VDD_BV) is thus limited to IDDMAX – IDD(VDD_HV), i.e., 80 mA.
Therefore, respecting the maximum power allowed as explained in Section 4.5.2, Package thermal characteristics, it is
recommended to use this resistor only in the 125 °C/5.5 V operating corner as per the following guidelines:
•
•
•
If IDD(VDD_BV) < 80 mA, then no resistor is required.
If 80 mA < IDD(VDD_BV) < 90 mA, then 4  resistor can be used.
If IDD(VDD_BV) > 90 mA, then 8  resistor can be used.
Using resistance in the range of 4–8 , the gain will be around 10–20% of total consumption on VDD_BV. For example, if 8 
resistor is used, then power consumption when IDD(VDD_BV) is 110 mA is equivalent to power consumption when
IDD(VDD_BV) is 90 mA (approximately) when resistor not used.
In order to ensure correct power up, the minimum VDD_BV to be guaranteed is 30 ms/V. If the supply ramp is slower than this
value, then LVDHV3B monitoring ballast supply VDD_BV pin gets triggered leading to device reset. Until the supply reaches
certain threshold, this low voltage detector (LVD) generates destructive reset event in the system. This threshold depends on
the maximum IDD(VDD_BV) possible across the external resistor.
4.5.2
Package thermal characteristics
Table 14. LQFP thermal characteristics1
Symbol
C
Parameter
Conditions2
Value
Pin count
Unit
Min Typ Max
RJA CC D Thermal resistance,
junction-to-ambient natural
convection3
Single-layer board — 1s
Four-layer board — 2s2p
RJB CC
Thermal resistance,
junction-to-board4
Single-layer board — 1s
Four-layer board — 2s2p
100
—
—
64
144
—
—
64
176
—
—
64
100
—
—
49.7
144
—
—
48.3
176
—
—
47.3
100
—
—
36
144
—
—
38
176
—
—
38
100
—
—
33.6
144
—
—
33.4
176
—
—
33.4
°C/W
°C/W
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
39
Electrical characteristics
Table 14. LQFP thermal characteristics1 (continued)
Symbol
C
Conditions2
Parameter
Value
Pin count
Unit
Min Typ Max
RJC CC
Thermal resistance,
junction-to-case5
Single-layer board — 1s
Four-layer board — 2s2p
100
—
—
23
144
—
—
23
176
—
—
23
100
—
—
19.8
144
—
—
19.2
176
—
—
18.8
°C/W
1
Thermal characteristics are targets based on simulation.
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C.
3 Junction-to-ambient thermal resistance determined per JEDEC JESD51-3 and JESD51-6. Thermal test board
meets JEDEC specification for this package. When Greek letters are not available, the symbols are typed as RthJA
and RthJMA.
4 Junction-to-board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC
specification for the specified package. When Greek letters are not available, the symbols are typed as RthJB.
5 Junction-to-case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate
temperature is used for the case temperature. Reported value includes the thermal resistance of the interface
layer. When Greek letters are not available, the symbols are typed as RthJC.
2
4.5.3
Power considerations
The average chip-junction temperature, TJ, in degrees Celsius, may be calculated using Equation 1:
TJ = TA + (PD x RJA)
Eqn. 1
Where:
TA is the ambient temperature in °C.
RJA is the package junction-to-ambient thermal resistance, in °C/W.
PD is the sum of PINT and PI/O (PD = PINT + PI/O).
PINT is the product of IDD and VDD, expressed in watts. This is the chip internal power.
PI/O represents the power dissipation on input and output pins; user determined.
Most of the time for the applications, PI/O < PINT and may be neglected. On the other hand, PI/O may be significant, if the device
is configured to continuously drive external modules and/or memories.
An approximate relationship between PD and TJ (if PI/O is neglected) is given by:
PD = K / (TJ + 273 °C)
Eqn. 2
K = PD x (TA + 273 °C) + RJA x PD2
Eqn. 3
Therefore, solving equations 1 and 2:
Where:
MPC5607B Microcontroller Data Sheet, Rev. 8
40
Freescale Semiconductor
Electrical characteristics
K is a constant for the particular part, which may be determined from Equation 3 by measuring PD (at equilibrium)
for a known TA. Using this value of K, the values of PD and TJ may be obtained by solving equations 1 and 2
iteratively for any value of TA.
4.6
4.6.1
I/O pad electrical characteristics
I/O pad types
The device provides four main I/O pad types depending on the associated alternate functions:
•
•
•
•
Slow pads—are the most common pads, providing a good compromise between transition time and low
electromagnetic emission.
Medium pads—provide transition fast enough for the serial communication channels with controlled current to reduce
electromagnetic emission.
Fast pads—provide maximum speed. These are used for improved Nexus debugging capability.
Input only pads—are associated with ADC channels and 32 kHz low power external crystal oscillator providing low
input leakage.
Medium and Fast pads can use slow configuration to reduce electromagnetic emission, at the cost of reducing AC performance.
4.6.2
I/O input DC characteristics
Table 15 provides input DC electrical characteristics as described in Figure 6.
VIN
VDD
VIH
VHYS
VIL
PDIx = ‘1
(GPDI register of SIUL)
PDIx = ‘0’
Figure 6. I/O input DC electrical characteristics definition
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
41
Electrical characteristics
Table 15. I/O input DC electrical characteristics
Symbol
C
Value
Conditions1
Parameter
Unit
Min
Typ
Max
VIH
SR P Input high level CMOS (Schmitt
Trigger)
—
0.65VDD
—
VDD + 0.4
VIL
SR P Input low level CMOS (Schmitt
Trigger)
—
0.4
—
0.35VDD
—
0.1VDD
—
—
TA = 40 °C
—
2
200
TA = 25 °C
—
2
200
D
TA = 85 °C
—
5
300
D
TA = 105 °C
—
12
500
P
TA = 125 °C
—
70
1000
VHYS CC C Input hysteresis CMOS (Schmitt
Trigger)
ILKG CC D Digital input leakage
No injection
on adjacent
pin
D
WFI
2
WNFI
2
V
nA
SR P Wakeup input filtered pulse
—
—
—
40
ns
SR P Wakeup input not filtered pulse
—
1000
—
—
ns
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
In the range from 40 to 1000 ns, pulses can be filtered or not filtered, according to operating temperature and
voltage.
1
2
4.6.3
I/O output DC characteristics
The following tables provide DC characteristics for bidirectional pads:
•
•
•
•
Table 16 provides weak pull figures. Both pull-up and pull-down resistances are supported.
Table 17 provides output driver characteristics for I/O pads when in SLOW configuration.
Table 18 provides output driver characteristics for I/O pads when in MEDIUM configuration.
Table 19 provides output driver characteristics for I/O pads when in FAST configuration.
Table 16. I/O pull-up/pull-down DC electrical characteristics
Symbol
C
Parameter
Value
Conditions1
Unit
Min
|IWPU| CC P Weak pull-up current
absolute value
C
P
|IWPD| CC P Weak pull-down current
absolute value
C
P
1
2
VIN = VIL, VDD = 5.0 V ± 10% PAD3V5V = 0
Typ Max
10
—
150
10
—
250
VIN = VIL, VDD = 3.3 V ± 10% PAD3V5V = 1
10
—
150
VIN = VIH, VDD = 5.0 V ± 10% PAD3V5V = 0
10
—
150
PAD3V5V = 1
10
—
250
VIN = VIH, VDD = 3.3 V ± 10% PAD3V5V = 1
10
—
150
PAD3V5V = 12
µA
µA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified.
The configuration PAD3V5 = 1 when VDD = 5 V is only a transient configuration during power-up. All pads but
RESET and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state.
MPC5607B Microcontroller Data Sheet, Rev. 8
42
Freescale Semiconductor
Electrical characteristics
Table 17. SLOW configuration output buffer electrical characteristics
Symbol
VOH
VOL
1
2
C
Value
Conditions1
Parameter
Unit
Min
Typ
Max
Push Pull IOH = 2 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 0
(recommended)
0.8VDD
—
—
C
IOH = 2 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 12
0.8VDD
—
—
C
IOH = 1 mA,
VDD = 3.3 V ± 10%,
PAD3V5V = 1
(recommended)
VDD  0.8
—
—
Push Pull IOL = 2 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 0
(recommended)
—
—
0.1VDD
C
IOL = 2 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 12
—
—
0.1VDD
C
IOL = 1 mA,
VDD = 3.3 V ± 10%,
PAD3V5V = 1
(recommended)
—
—
0.5
CC P Output high level
SLOW configuration
CC P Output low level
SLOW configuration
V
V
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
The configuration PAD3V5 = 1 when VDD = 5 V is only a transient configuration during power-up. All pads but
RESET and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state.
Table 18. MEDIUM configuration output buffer electrical characteristics
Symbol C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
Push Pull IOH = 3.8 mA,
VOH CC C Output high level
MEDIUM configuration
VDD = 5.0 V ± 10%, PAD3V5V = 0
0.8VDD
—
—
P
IOH = 2 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 0
(recommended)
0.8VDD
—
—
C
IOH = 1 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 12
0.8VDD
—
—
C
IOH = 1 mA,
VDD = 3.3 V ± 10%, PAD3V5V = 1
(recommended)
VDD  0.8 —
—
C
IOH = 100 µA,
VDD = 5.0 V ± 10%, PAD3V5V = 0
0.8VDD
—
V
—
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
43
Electrical characteristics
Table 18. MEDIUM configuration output buffer electrical characteristics (continued)
Symbol C
Parameter
Value
Conditions1
Unit
Min
VOL CC C Output low level
Push Pull IOL = 3.8 mA,
MEDIUM configuration
VDD = 5.0 V ± 10%, PAD3V5V = 0
1
2
Typ
Max
—
— 0.2VDD
P
IOL = 2 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 0
(recommended)
—
— 0.1VDD
C
IOL = 1 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 12
—
— 0.1VDD
C
IOL = 1 mA,
VDD = 3.3 V ± 10%, PAD3V5V = 1
(recommended)
—
—
C
IOL = 100 µA,
VDD = 5.0 V ± 10%, PAD3V5V = 0
—
— 0.1VDD
V
0.5
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
The configuration PAD3V5 = 1 when VDD = 5 V is only a transient configuration during power-up. All pads but
RESET and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state.
Table 19. FAST configuration output buffer electrical characteristics
Symbol
Parameter
Value
Conditions1
Unit
Min
Typ
Max
VOH CC P Output high level Push Pull IOH = 14 mA,
FAST configuration
VDD = 5.0 V ± 10%,
PAD3V5V = 0
(recommended)
0.8VDD
—
—
C
IOH = 7 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 12
0.8VDD
—
—
C
IOH = 11 mA,
VDD = 3.3 V ± 10%,
PAD3V5V = 1
(recommended)
VDD  0.8
—
—
—
—
0.1VDD
VOL
1
C
CC P Output low level
Push Pull IOL = 14 mA,
FAST configuration
VDD = 5.0 V ± 10%,
PAD3V5V = 0
(recommended)
C
IOL = 7 mA,
VDD = 5.0 V ± 10%,
PAD3V5V = 12
—
—
0.1VDD
C
IOL = 11 mA,
VDD = 3.3 V ± 10%,
PAD3V5V = 1
(recommended)
—
—
0.5
V
V
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
MPC5607B Microcontroller Data Sheet, Rev. 8
44
Freescale Semiconductor
Electrical characteristics
2
The configuration PAD3V5 = 1 when VDD = 5 V is only a transient configuration during power-up. All pads but
RESET and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state.
4.6.4
Output pin transition times
Table 20. Output pin transition times
Symbol
C
Value
Conditions1
Parameter
Unit
Min Typ Max
ttr
CC D Output transition time output pin2 CL = 25 pF
SLOW configuration
T
CL = 50 pF
D
CL = 100 pF
D
CL = 25 pF
T
CL = 50 pF
ttr
VDD = 3.3 V ± 10%,
PAD3V5V = 1
CL = 100 pF
D
ttr
VDD = 5.0 V ± 10%,
PAD3V5V = 0
CC D Output transition time output
MEDIUM configuration
T
pin2
CL = 25 pF
CL = 50 pF
D
CL = 100 pF
D
CL = 25 pF
T
CL = 50 pF
D
CL = 100 pF
CC D Output transition time output pin2 CL = 25 pF
FAST configuration
CL = 50 pF
VDD = 5.0 V ± 10%,
PAD3V5V = 0
SIUL.PCRx.SRC = 1
VDD = 3.3 V ± 10%,
PAD3V5V = 1
SIUL.PCRx.SRC = 1
VDD = 5.0 V ± 10%,
PAD3V5V = 0
CL = 100 pF
CL = 25 pF
CL = 50 pF
VDD = 3.3 V ± 10%,
PAD3V5V = 1
CL = 100 pF
1
2
4.6.5
—
—
50
—
—
100
—
—
125
—
—
50
—
—
100
—
—
125
—
—
10
—
—
20
—
—
40
—
—
12
—
—
25
—
—
40
—
—
4
—
—
6
—
—
12
—
—
4
—
—
7
—
—
12
ns
ns
ns
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
CL includes device and package capacitances (CPKG < 5 pF).
I/O pad current specification
The I/O pads are distributed across the I/O supply segment. Each I/O supply segment is associated to a VDD/VSS supply pair as
described in Table 21.
Table 22 provides I/O consumption figures.
In order to ensure device reliability, the average current of the I/O on a single segment should remain below the IAVGSEG
maximum value.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
45
Electrical characteristics
Table 21. I/O supply segments
Supply segment
Package
1
208
MAPBGA1
1
2
3
4
5
6
Equivalent to 176 LQFP segment pad distribution
7
8
MCKO
MDOn
/MSEO
176 LQFP
pin7 –
pin27
pin28 –
pin57
pin59 –
pin85
pin86 –
pin123
pin124 –
pin150
pin151 –
pin6
—
—
144 LQFP
pin20 –
pin49
pin51 –
pin99
pin100 –
pin122
pin 123 –
pin19
—
—
—
—
100 LQFP
pin16 –
pin35
pin37 –
pin69
pin70 –
pin83
pin84 –
pin15
—
—
—
—
208 MAPBGA available only as development package for Nexus2+
Table 22. I/O consumption
Symbol
C
Value
Conditions1
Parameter
Unit
Min Typ Max
ISWTSLW,2 CC D Dynamic I/O current for
SLOW configuration
ISWTMED2 CC D Dynamic I/O current for
MEDIUM configuration
ISWTFST2 CC D Dynamic I/O current for
FAST configuration
IRMSSLW CC D Root mean square I/O
current for SLOW
configuration
CL = 25 pF
CL = 25 pF
CL = 25 pF
CL = 25 pF, 2 MHz
CL = 25 pF, 4 MHz
VDD = 5.0 V ± 10%,
PAD3V5V = 0
—
—
20
VDD = 3.3 V ± 10%,
PAD3V5V = 1
—
—
16
VDD = 5.0 V ± 10%,
PAD3V5V = 0
—
—
29
VDD = 3.3 V ± 10%,
PAD3V5V = 1
—
—
17
VDD = 5.0 V ± 10%,
PAD3V5V = 0
—
—
110 mA
VDD = 3.3 V ± 10%,
PAD3V5V = 1
—
—
50
VDD = 5.0 V ± 10%,
PAD3V5V = 0
—
—
2.3
—
—
3.2
—
—
6.6
—
—
1.6
—
—
2.3
—
—
4.7
—
—
6.6
—
— 13.4
—
— 18.3
—
—
5
—
—
8.5
—
—
11
CL = 100 pF, 2 MHz
CL = 25 pF, 2 MHz
CL = 25 pF, 4 MHz
VDD = 3.3 V ± 10%,
PAD3V5V = 1
CL = 100 pF, 2 MHz
IRMSMED CC D Root mean square I/O
current for MEDIUM
configuration
CL = 25 pF, 13 MHz
CL = 25 pF, 40 MHz
VDD = 5.0 V ± 10%,
PAD3V5V = 0
CL = 100 pF, 13 MHz
CL = 25 pF, 13 MHz
CL = 25 pF, 40 MHz
VDD = 3.3 V ± 10%,
PAD3V5V = 1
CL = 100 pF, 13 MHz
mA
mA
mA
mA
MPC5607B Microcontroller Data Sheet, Rev. 8
46
Freescale Semiconductor
Electrical characteristics
Table 22. I/O consumption (continued)
Symbol
C
Value
Conditions1
Parameter
Unit
Min Typ Max
IRMSFST
CC D Root mean square I/O
current for FAST
configuration
CL = 25 pF, 40 MHz
VDD = 5.0 V ± 10%,
PAD3V5V = 0
—
—
22
—
—
33
—
—
56
—
—
14
—
—
20
CL = 100 pF, 40 MHz
—
—
35
VDD = 5.0 V ± 10%, PAD3V5V = 0
—
—
70
VDD = 3.3 V ± 10%, PAD3V5V = 1
—
—
65
CL = 25 pF, 64 MHz
CL = 100 pF, 40 MHz
CL = 25 pF, 40 MHz
VDD = 3.3 V ± 10%,
PAD3V5V = 1
CL = 25 pF, 64 MHz
IAVGSEG
1
2
SR D Sum of all the static I/O
current within a supply
segment
mA
mA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to125 °C, unless otherwise specified
Stated maximum values represent peak consumption that lasts only a few ns during I/O transition.
Table 23 provides the weight of concurrent switching I/Os.
Due to the dynamic current limitations, the sum of the weight of concurrent switching I/Os on a single segment must not exceed
100% to ensure device functionality.
Table 23. I/O weight1
176 LQFP
144/100 LQFP
Supply segment
Pad
176
LQFP
144
LQFP
100
LQFP
6
4
4
—
—
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
PB[3]
5%
—
6%
—
13%
—
15%
—
PC[9]
4%
—
5%
—
13%
—
15%
—
PC[14]
4%
—
4%
—
13%
—
15%
—
PC[15]
3%
4%
4%
4%
12%
18%
15%
16%
PJ[4]
3%
4%
3%
3%
—
—
—
—
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
47
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
176
LQFP
144
LQFP
100
LQFP
1
—
—
PH[15]
2%
3%
3%
3%
—
—
—
—
—
—
PH[13]
3%
4%
3%
4%
—
—
—
—
—
—
PH[14]
3%
4%
4%
4%
—
—
—
—
—
—
PI[6]
4%
—
4%
—
—
—
—
—
—
—
PI[7]
4%
—
4%
—
—
—
—
—
4
—
PG[5]
4%
—
5%
—
10%
—
12%
—
—
PG[4]
4%
6%
5%
5%
9%
13%
11%
12%
—
PG[3]
4%
—
5%
—
9%
—
11%
—
—
PG[2]
4%
6%
5%
5%
9%
12%
10%
11%
4
PA[2]
4%
—
5%
—
8%
—
10%
—
PE[0]
4%
—
5%
—
8%
—
9%
—
PA[1]
4%
—
5%
—
8%
—
9%
—
PE[1]
4%
6%
5%
6%
7%
10%
9%
9%
PE[8]
4%
6%
5%
6%
7%
10%
8%
9%
PE[9]
4%
—
5%
—
6%
—
8%
—
PE[10]
4%
—
5%
—
6%
—
7%
—
PA[0]
4%
6%
5%
5%
6%
8%
7%
7%
PE[11]
4%
—
5%
—
5%
—
6%
—
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
MPC5607B Microcontroller Data Sheet, Rev. 8
48
Freescale Semiconductor
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
176
LQFP
144
LQFP
100
LQFP
2
1
—
PG[9]
9%
—
10%
—
9%
—
10%
—
—
PG[8]
9%
—
11%
—
9%
—
11%
—
1
PC[11]
9%
—
11%
—
9%
—
11%
—
PC[10]
9%
13%
11%
12%
9%
13%
11%
12%
—
PG[7]
9%
—
11%
—
9%
—
11%
—
—
PG[6]
10%
14%
11%
12%
10%
14%
11%
12%
1
PB[0]
10%
14%
12%
12%
10%
14%
12%
12%
PB[1]
10%
—
12%
—
10%
—
12%
—
—
PF[9]
10%
—
12%
—
10%
—
12%
—
—
PF[8]
10%
14%
12%
13%
10%
14%
12%
13%
—
PF[12]
10%
15%
12%
13%
10%
15%
12%
13%
1
PC[6]
10%
—
12%
—
10%
—
12%
—
PC[7]
10%
—
12%
—
10%
—
12%
—
—
PF[10]
10%
14%
11%
12%
10%
14%
11%
12%
—
PF[11]
9%
—
11%
—
9%
—
11%
—
1
PA[15]
8%
12%
10%
10%
8%
12%
10%
10%
—
PF[13]
8%
—
10%
—
8%
—
10%
—
1
PA[14]
8%
11%
9%
10%
8%
11%
9%
10%
PA[4]
7%
—
9%
—
7%
—
9%
—
PA[13]
7%
10%
8%
9%
7%
10%
8%
9%
PA[12]
7%
—
8%
—
7%
—
8%
—
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
49
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
176
LQFP
144
LQFP
100
LQFP
3
2
2
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
PB[9]
1%
—
1%
—
1%
—
1%
—
PB[8]
1%
—
1%
—
1%
—
1%
—
PB[10]
5%
—
6%
—
6%
—
7%
—
—
PF[0]
5%
—
6%
—
6%
—
8%
—
—
PF[1]
5%
—
6%
—
7%
—
8%
—
—
PF[2]
6%
—
7%
—
7%
—
9%
—
—
PF[3]
6%
—
7%
—
8%
—
9%
—
—
PF[4]
6%
—
7%
—
8%
—
10%
—
—
PF[5]
6%
—
7%
—
9%
—
10%
—
—
PF[6]
6%
—
7%
—
9%
—
11%
—
—
PF[7]
6%
—
7%
—
9%
—
11%
—
—
—
PJ[3]
6%
—
7%
—
—
—
—
—
—
—
PJ[2]
6%
—
7%
—
—
—
—
—
—
—
PJ[1]
6%
—
7%
—
—
—
—
—
—
—
PJ[0]
6%
—
7%
—
—
—
—
—
—
—
PI[15]
6%
—
7%
—
—
—
—
—
—
—
PI[14]
6%
—
7%
—
—
—
—
—
2
2
PD[0]
1%
—
1%
—
1%
—
1%
—
PD[1]
1%
—
1%
—
1%
—
1%
—
PD[2]
1%
—
1%
—
1%
—
1%
—
PD[3]
1%
—
1%
—
1%
—
1%
—
PD[4]
1%
—
1%
—
1%
—
1%
—
PD[5]
1%
—
1%
—
1%
—
1%
—
PD[6]
1%
—
1%
—
1%
—
2%
—
PD[7]
1%
—
1%
—
1%
—
2%
—
MPC5607B Microcontroller Data Sheet, Rev. 8
50
Freescale Semiconductor
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
176
LQFP
144
LQFP
100
LQFP
4
2
2
4
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
PD[8]
1%
—
1%
—
1%
—
2%
—
PB[4]
1%
—
1%
—
1%
—
2%
—
PB[5]
1%
—
1%
—
1%
—
2%
—
PB[6]
1%
—
1%
—
1%
—
2%
—
PB[7]
1%
—
1%
—
1%
—
2%
—
PD[9]
1%
—
1%
—
1%
—
2%
—
PD[10]
1%
—
1%
—
1%
—
2%
—
PD[11]
1%
—
1%
—
1%
—
2%
—
—
—
PB[11]
1%
—
1%
—
—
—
—
—
—
—
PD[12]
11%
—
13%
—
—
—
—
—
2
2
PB[12]
11%
—
13%
—
15%
—
17%
—
PD[13]
11%
—
13%
—
14%
—
17%
—
PB[13]
11%
—
13%
—
14%
—
17%
—
PD[14]
11%
—
13%
—
14%
—
17%
—
PB[14]
11%
—
13%
—
14%
—
16%
—
PD[15]
11%
—
13%
—
13%
—
16%
—
PB[15]
11%
—
13%
—
13%
—
15%
—
—
—
PI[8]
10%
—
12%
—
—
—
—
—
—
—
PI[9]
10%
—
12%
—
—
—
—
—
—
—
PI[10]
10%
—
12%
—
—
—
—
—
—
—
PI[11]
10%
—
12%
—
—
—
—
—
—
—
PI[12]
10%
—
12%
—
—
—
—
—
—
—
PI[13]
10%
—
11%
—
—
—
—
—
2
2
PA[3]
9%
—
11%
—
11%
—
13%
—
—
PG[13]
9%
13%
11%
11%
10%
14%
12%
13%
—
PG[12]
9%
13%
10%
11%
10%
14%
12%
12%
—
PH[0]
6%
8%
7%
7%
6%
9%
7%
8%
—
PH[1]
6%
8%
7%
7%
6%
8%
7%
7%
—
PH[2]
5%
7%
6%
6%
5%
7%
6%
7%
—
PH[3]
5%
7%
5%
6%
5%
7%
6%
6%
—
PG[1]
4%
—
5%
—
4%
—
5%
—
—
PG[0]
4%
5%
4%
5%
4%
5%
4%
5%
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
51
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
176
LQFP
144
LQFP
100
LQFP
5
3
—
PF[15]
4%
—
4%
—
4%
—
4%
—
—
PF[14]
4%
6%
5%
5%
4%
6%
5%
5%
—
PE[13]
4%
—
5%
—
4%
—
5%
—
3
PA[7]
5%
—
6%
—
5%
—
6%
—
PA[8]
5%
—
6%
—
5%
—
6%
—
PA[9]
6%
—
7%
—
6%
—
7%
—
PA[10]
6%
—
8%
—
6%
—
8%
—
PA[11]
8%
—
9%
—
8%
—
9%
—
PE[12]
8%
—
9%
—
8%
—
9%
—
—
PG[14]
8%
—
9%
—
8%
—
9%
—
—
PG[15]
8%
11%
9%
10%
8%
11%
9%
10%
—
PE[14]
8%
—
9%
—
8%
—
9%
—
—
PE[15]
8%
11%
9%
10%
8%
11%
9%
10%
—
PG[10]
8%
—
9%
—
8%
—
9%
—
—
PG[11]
7%
11%
9%
9%
7%
11%
9%
9%
—
—
PH[11]
7%
10%
9%
9%
—
—
—
—
—
—
PH[12]
7%
10%
8%
9%
—
—
—
—
—
—
PI[5]
7%
—
8%
—
—
—
—
—
—
—
PI[4]
7%
—
8%
—
—
—
—
—
3
3
PC[3]
6%
—
8%
—
6%
—
8%
—
PC[2]
6%
8%
7%
7%
6%
8%
7%
7%
PA[5]
6%
8%
7%
7%
6%
8%
7%
7%
PA[6]
5%
—
6%
—
5%
—
6%
—
PH[10]
5%
7%
6%
6%
5%
7%
6%
6%
PC[1]
5%
19%
5%
13%
5%
19%
5%
13%
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
MPC5607B Microcontroller Data Sheet, Rev. 8
52
Freescale Semiconductor
Electrical characteristics
Table 23. I/O weight1 (continued)
176 LQFP
144/100 LQFP
Supply segment
Pad
1
2
4.7
176
LQFP
144
LQFP
100
LQFP
6
4
4
Weight 5 V
Weight 3.3 V
Weight 5 V
Weight 3.3 V
SRC2 = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1 SRC = 0 SRC = 1
PC[0]
6%
9%
7%
8%
7%
10%
8%
8%
PH[9]
7%
—
8%
—
7%
—
9%
—
PE[2]
7%
10%
8%
9%
8%
11%
9%
10%
PE[3]
7%
10%
9%
9%
8%
12%
10%
10%
PC[5]
7%
11%
9%
9%
8%
12%
10%
11%
PC[4]
8%
11%
9%
10%
9%
13%
10%
11%
PE[4]
8%
11%
9%
10%
9%
13%
11%
12%
PE[5]
8%
11%
10%
10%
9%
14%
11%
12%
—
PH[4]
8%
12%
10%
10%
10%
14%
12%
12%
—
PH[5]
8%
—
10%
—
10%
—
12%
—
—
PH[6]
8%
12%
10%
11%
10%
15%
12%
13%
—
PH[7]
9%
12%
10%
11%
11%
15%
13%
13%
—
PH[8]
9%
12%
10%
11%
11%
16%
13%
14%
4
PE[6]
9%
12%
10%
11%
11%
16%
13%
14%
PE[7]
9%
12%
10%
11%
11%
16%
14%
14%
—
—
PI[3]
9%
—
10%
—
—
—
—
—
—
—
PI[2]
9%
—
10%
—
—
—
—
—
—
—
PI[1]
9%
—
10%
—
—
—
—
—
—
—
PI[0]
9%
—
10%
—
—
—
—
—
4
4
PC[12]
8%
12%
10%
11%
12%
18%
15%
16%
PC[13]
8%
—
10%
—
13%
—
15%
—
PC[8]
8%
—
10%
—
13%
—
15%
—
PB[2]
8%
11%
9%
10%
13%
18%
15%
16%
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
SRC: “Slew Rate Control” bit in SIU_PCRx
RESET electrical characteristics
The device implements a dedicated bidirectional RESET pin.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
53
Electrical characteristics
VDD
VDDMIN
RESET
VIH
VIL
device reset forced by RESET
device start-up phase
Figure 7. Start-up reset requirements
VRESET
hw_rst
VDD
‘1’
VIH
VIL
‘0’
filtered by
hysteresis
filtered by
lowpass filter
WFRST
filtered by
lowpass filter
unknown reset
state
device under hardware reset
WFRST
WNFRST
Figure 8. Noise filtering on reset signal
Table 24. Reset electrical characteristics
Symbol
C
Parameter
Value
Conditions1
Unit
Min
VIH
SR P Input High Level CMOS
(Schmitt Trigger)
—
Typ
Max
0.65VDD — VDD + 0.4
V
MPC5607B Microcontroller Data Sheet, Rev. 8
54
Freescale Semiconductor
Electrical characteristics
Table 24. Reset electrical characteristics (continued)
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
VIL
SR P Input low Level CMOS
(Schmitt Trigger)
—
0.4
—
0.35VDD
V
VHYS
CC C Input hysteresis CMOS
(Schmitt Trigger)
—
0.1VDD
—
—
V
Push Pull, IOL = 2 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 0
(recommended)
—
—
0.1VDD
V
Push Pull, IOL = 1 mA,
VDD = 5.0 V ± 10%, PAD3V5V = 12
—
—
0.1VDD
Push Pull, IOL = 1 mA,
VDD = 3.3 V ± 10%, PAD3V5V = 1
(recommended)
—
—
0.5
CL = 25 pF,
VDD = 5.0 V ± 10%, PAD3V5V = 0
—
—
10
CL = 50 pF,
VDD = 5.0 V ± 10%, PAD3V5V = 0
—
—
20
CL = 100 pF,
VDD = 5.0 V ± 10%, PAD3V5V = 0
—
—
40
CL = 25 pF,
VDD = 3.3 V ± 10%, PAD3V5V = 1
—
—
12
CL = 50 pF,
VDD = 3.3 V ± 10%, PAD3V5V = 1
—
—
25
CL = 100 pF,
VDD = 3.3 V ± 10%, PAD3V5V = 1
—
—
40
WFRST SR P RESET input filtered pulse
—
—
—
40
ns
WNFRST SR P RESET input not filtered pulse
—
1000
—
—
ns
10
—
150
µA
10
—
150
10
—
250
VOL
ttr
|IWPU|
CC P Output low level
CC D Output transition time output
pin3 MEDIUM configuration
CC P Weak pull-up current absolute VDD = 3.3 V ± 10%, PAD3V5V = 1
value
D
VDD = 5.0 V ± 10%, PAD3V5V = 0
P
VDD = 5.0 V ± 10%, PAD3V5V = 14
ns
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
This is a transient configuration during power-up, up to the end of reset PHASE2 (refer to RGM module section of
the device reference manual).
3 C includes device and package capacitance (C
L
PKG < 5 pF).
4 The configuration PAD3V5 = 1 when V
DD = 5 V is only transient configuration during power-up. All pads but RESET
and Nexus output (MDOx, EVTO, MCKO) are configured in input or in high impedance state.
1
2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
55
Electrical characteristics
4.8
Power management electrical characteristics
4.8.1
Voltage regulator electrical characteristics
The device implements an internal voltage regulator to generate the low voltage core supply VDD_LV from the high voltage
ballast supply VDD_BV. The regulator itself is supplied by the common I/O supply VDD. The following supplies are involved:
•
•
•
HV: High voltage external power supply for voltage regulator module. This must be provided externally through VDD
power pin.
BV: High voltage external power supply for internal ballast module. This must be provided externally through VDD_BV
power pin. Voltage values should be aligned with VDD.
LV: Low voltage internal power supply for core, FMPLL and Flash digital logic. This is generated by the internal
voltage regulator but provided outside to connect stability capacitor. It is further split into four main domains to ensure
noise isolation between critical LV modules within the device:
— LV_COR: Low voltage supply for the core. It is also used to provide supply for FMPLL through double bonding.
— LV_CFLA: Low voltage supply for code flash module. It is supplied with dedicated ballast and shorted to
LV_COR through double bonding.
— LV_DFLA: Low voltage supply for data flash module. It is supplied with dedicated ballast and shorted to
LV_COR through double bonding.
— LV_PLL: Low voltage supply for FMPLL. It is shorted to LV_COR through double bonding.
CREG2 (LV_COR/LV_CFLA)
VDD
VSS_LV
VDD_BV
Voltage Regulator
I
VSS_LVn
DEVICE
VDD_BV
CREG1 (LV_COR/LV_DFLA)
VDD_LVn
CDEC1 (Ballast decoupling)
VREF
VDD_LV
VDD_LV
DEVICE
VSS_LV
VSS_LV
VDD_LV
CREG3
(LV_COR/LV_PLL)
VSS
VDD
CDEC2
(supply/IO decoupling)
Figure 9. Voltage regulator capacitance connection
The internal voltage regulator requires external capacitance (CREGn) to be connected to the device in order to provide a stable
low voltage digital supply to the device. Capacitances should be placed on the board as near as possible to the associated pins.
Care should also be taken to limit the serial inductance of the board to less than 5 nH.
MPC5607B Microcontroller Data Sheet, Rev. 8
56
Freescale Semiconductor
Electrical characteristics
Each decoupling capacitor must be placed between each of the three VDD_LV/VSS_LV supply pairs to ensure stable voltage (see
Section 4.4, Recommended operating conditions).
Table 25. Voltage regulator electrical characteristics
Symbol
C
Parameter
Value
Conditions1
—
Unit
Min
Typ
Max
200
—
500
nF
—
—
0.2

4704
—
nF
CREGn
SR — Internal voltage regulator external
capacitance
RREG
SR — Stability capacitor equivalent serial
resistance
Range:
10 kHz to 20 MHz
CDEC1
SR — Decoupling capacitance2 ballast
VDD_BV/VSS_LV pair:
VDD_BV = 4.5 V to 5.5 V
1003
VDD_BV/VSS_LV pair:
VDD_BV = 3 V to 3.6 V
400
—
CDEC2
SR — Decoupling capacitance regulator
supply
VDD/VSS pair
10
100
—
nF
VMREG
CC T Main regulator output voltage
Before exiting from reset
—
1.32
—
V
1.16
1.28
—
—
—
150
mA
mA
P
IMREG
IMREGINT
After trimming
SR — Main regulator current provided to
VDD_LV domain
—
CC D Main regulator module current
consumption
IMREG = 200 mA
—
—
2
IMREG = 0 mA
—
—
1
VLPREG
CC P Low-power regulator output voltage
After trimming
1.16
1.28
—
V
ILPREG
SR — Low-power regulator current provided
to VDD_LV domain
—
—
15
mA
—
—
600
µA
ILPREG = 0 mA;
TA = 55 °C
—
5
—
After trimming
1.16
1.28
—
V
—
—
5
mA
IULPREG = 5 mA;
TA = 55 °C
—
—
100
µA
IULPREG = 0 mA;
TA = 55 °C
—
2
—
—
—
3006
ILPREGINT
CC D Low-power regulator module current ILPREG = 15 mA;
consumption
TA = 55 °C
—
VULPREG
CC P Ultra low power regulator output
voltage
IULPREG
SR — Ultra low power regulator current
provided to VDD_LV domain
IULPREGINT
CC D Ultra low power regulator module
current consumption
IDD_BV
—
CC D In-rush average current on VDD_BV
during power-up5
—
—
mA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
This capacitance value is driven by the constraints of the external voltage regulator supplying the VDD_BV voltage. A
typical value is in the range of 470 nF.
3
This value is acceptable to guarantee operation from 4.5 V to 5.5 V
1
2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
57
Electrical characteristics
4
External regulator and capacitance circuitry must be capable of providing IDD_BV while maintaining supply VDD_BV in
operating range.
5
In-rush average current is seen only for short time during power-up and on standby exit (maximum 20 µs, depending
on external capacitances to be loaded).
6
The duration of the in-rush current depends on the capacitance placed on LV pins. BV decoupling capacitors must
be sized accordingly. Refer to IMREG value for minimum amount of current to be provided in cc.
4.8.2
Low voltage detector electrical characteristics
The device implements a power-on reset (POR) module to ensure correct power-up initialization, as well as five low voltage
detectors (LVDs) to monitor the VDD and the VDD_LV voltage while device is supplied:
•
•
•
•
•
•
POR monitors VDD during the power-up phase to ensure device is maintained in a safe reset state (refer to RGM
Destructive Event Status (RGM_DES) Register flag F_POR in device reference manual)
LVDHV3 monitors VDD to ensure device reset below minimum functional supply (refer to RGM Destructive Event
Status (RGM_DES) Register flag F_LVD27 in device reference manual)
LVDHV3B monitors VDD_BV to ensure device reset below minimum functional supply (refer to RGM Destructive
Event Status (RGM_DES) Register flag F_LVD27_VREG in device reference manual)
LVDHV5 monitors VDD when application uses device in the 5.0 V ± 10% range (refer to RGM Functional Event Status
(RGM_FES) Register flag F_LVD45 in device reference manual)
LVDLVCOR monitors power domain No. 1 (refer to RGM Destructive Event Status (RGM_DES) Register flag
F_LVD12_PD1 in device reference manual)
LVDLVBKP monitors power domain No. 0 (refer to RGM Destructive Event Status (RGM_DES) Register flag
F_LVD12_PD0 in device reference manual)
NOTE
When enabled, power domain No. 2 is monitored through LVDLVBKP.
VDD
VLVDHVxH
VLVDHVxL
RESET
Figure 10. Low voltage detector vs reset
MPC5607B Microcontroller Data Sheet, Rev. 8
58
Freescale Semiconductor
Electrical characteristics
Table 26. Low voltage detector electrical characteristics
Symbol
1
4.9
C
VPORUP
SR P Supply for functional POR module
VPORH
CC P Power-on reset threshold
Value
Conditions1
Parameter
TA = 25 °C,
after trimming
Unit
Min
Typ
Max
1.0
—
5.5
1.5
—
2.6
VLVDHV3H
CC T LVDHV3 low voltage detector high threshold
—
—
2.95
VLVDHV3L
CC P LVDHV3 low voltage detector low threshold
2.6
—
2.9
VLVDHV3BH
CC P LVDHV3B low voltage detector high threshold
—
—
2.95
VLVDHV3BL
CC P LVDHV3B low voltage detector low threshold
2.6
—
2.9
VLVDHV5H
CC T LVDHV5 low voltage detector high threshold
—
—
4.5
VLVDHV5L
CC P LVDHV5 low voltage detector low threshold
3.8
—
4.4
VLVDLVCORL CC P LVDLVCOR low voltage detector low threshold
1.08
—
1.16
VLVDLVBKPL
1.08
—
1.16
CC P LVDLVBKP low voltage detector low threshold
V
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
Power consumption
Table 27 provides DC electrical characteristics for significant application modes. These values are indicative values; actual
consumption depends on the application.
Table 27. Power consumption on VDD_BV and VDD_HV
Symbol
C
Parameter
Typ
Max
—
115
1403 mA
fCPU = 8 MHz
—
12
—
fCPU = 16 MHz
—
27
—
T
fCPU = 32 MHz
—
43
—
P
fCPU = 48 MHz
—
56
100
fCPU = 64 MHz
—
70
125
TA = 25 °C
—
10
18
TA = 125 °C
—
17
28
TA = 25 °C
—
350
9008
TA = 55 °C
—
750
—
D
TA = 85 °C
—
2
7
D
TA = 105 °C
—
4
10
P
TA = 125 °C
—
7
14
CC T RUN mode typical average
current5
T
P
IDDHALT
CC C HALT mode
current6
P
IDDSTOP
Unit
Min
IDDMAX2 CC D RUN mode maximum average
current
IDDRUN4
Value
Conditions1
CC P STOP mode current7
D
—
Slow internal RC
oscillator (128 kHz)
running
Slow internal RC
oscillator (128 kHz)
running
mA
mA
µA
mA
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
59
Electrical characteristics
Table 27. Power consumption on VDD_BV and VDD_HV (continued)
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
TA = 25 °C
—
30
100
TA = 55 °C
—
75
—
D
TA = 85 °C
—
180
700
D
TA = 105 °C
—
315
1000
P
TA = 125 °C
—
560
1700
TA = 25 °C
—
20
60
TA = 55 °C
—
45
—
D
TA = 85 °C
—
100
350
D
TA = 105 °C
—
165
500
D
TA = 125 °C
—
280
900
IDDSTDBY2 CC P STANDBY2 mode current9
D
IDDSTDBY1 CC T STANDBY1 mode current10
D
Slow internal RC
oscillator (128 kHz)
running
Slow internal RC
oscillator (128 kHz)
running
µA
µA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
Running consumption does not include I/Os toggling which is highly dependent on the application. The given value
is thought to be a worst case value with all peripherals running, and code fetched from code flash while modify
operation ongoing on data flash. Notice that this value can be significantly reduced by application: switch off not
used peripherals (default), reduce peripheral frequency through internal prescaler, fetch from RAM most used
functions, use low power mode when possible.
3 Higher current may be sunk by device during power-up and standby exit. Please refer to in-rush average current in
Table 25.
4 RUN current measured with typical application with accesses on both Flash and RAM.
5 Only for the “P” classification: Data and Code Flash in Normal Power. Code fetched from RAM: Serial IPs CAN and
LIN in loop back mode, DSPI as Master, PLL as system clock (4 x Multiplier) peripherals on (eMIOS/CTU/ADC) and
running at max frequency, periodic SW/WDG timer reset enabled.
6 Data Flash Power Down. Code Flash in Low Power. SIRC 128 kHz and FIRC 16 MHz on. 10 MHz XTAL clock.
FlexCAN: instances: 0, 1, 2 ON (clocked but not reception or transmission), instances: 4, 5, 6 clocks gated. LINFlex:
instances: 0, 1, 2 ON (clocked but not reception or transmission), instance: 3 to 9 clocks gated. eMIOS: instance:
0 ON (16 channels on PA[0]–PA[11] and PC[12]–PC[15]) with PWM 20 kHz, instance: 1 clock gated. DSPI:
instance: 0 (clocked but no communication), instance: 1 to 5 clocks gated. RTC/API ON. PIT ON. STM ON. ADC1
OFF. ADC0 ON but no conversion except two analog watchdogs.
7 Only for the “P” classification: No clock, FIRC 16 MHz off, SIRC 128 kHz on, PLL off, HPvreg off,
ULPVreg/LPVreg on. All possible peripherals off and clock gated. Flash in power down mode.
8 When going from RUN to STOP mode and the core consumption is > 6 mA, it is normal operation for the main
regulator module to be kept on by the on-chip current monitoring circuit. This is most likely to occur with junction
temperatures exceeding 125 °C and under these circumstances, it is possible for the current to initially exceed the
maximum STOP specification by up to 2 mA. After entering stop, the application junction temperature will reduce
to the ambient level and the main regulator will be automatically switched off when the load current is below 6 mA.
9 Only for the “P” classification: ULPreg on, HP/LPVreg off, 32 KB RAM on, device configured for minimum
consumption, all possible modules switched off.
10 ULPreg on, HP/LPVreg off, 8 KB RAM on, device configured for minimum consumption, all possible modules
switched off.
1
2
MPC5607B Microcontroller Data Sheet, Rev. 8
60
Freescale Semiconductor
Electrical characteristics
4.10
Flash memory electrical characteristics
4.10.1
Program/erase characteristics
Table 28 shows the program and erase characteristics.
Table 28. Program and erase specifications
Value
Symbol
tdwprogram
C
Parameter
CC C Double word (64 bits) program time4
Conditions
Code Flash
Min Typ1
—
Data Flash
16 KB block preprogram and erase time
t16Kpperase
Code Flash
32 KB block preprogram and erase time
Code Flash
—
128 KB block preprogram and erase time
Code Flash
—
1
2
3
4
5
D Erase Suspend Latency
tESRT
C Erase Suspend Request Rate5
500
µs
200
500
5000
ms
300
600
5000
ms
1300
7500
ms
400
—
Data Flash
tesus
50
300
Data Flash
t128Kpperase
Unit
22
Data Flash
t32Kpperase
18
Initial
Max3
max2
600
800
—
—
—
30
30
µs
Code Flash
20
—
—
—
ms
Data Flash
10
—
—
—
Typical program and erase times assume nominal supply values and operation at 25 °C. All times are subject to
change pending device characterization.
Initial factory condition: < 100 program/erase cycles, 25 °C, typical supply voltage.
The maximum program and erase times occur after the specified number of program/erase cycles. These maximum
values are characterized but not guaranteed.
Actual hardware programming times. This does not include software overhead.
Time between erase suspend resume and the next erase suspend request
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
61
Electrical characteristics
Table 29. Flash module life
Value
Symbol
1
C
Parameter
Conditions
Unit
Min
Typ
Max
P/E
CC C Number of program/erase
cycles per block for 16 KB
blocks over the operating
temperature range (TJ)
—
100,000
—
—
cycles
P/E
CC C Number of program/erase
cycles per block for 32 KB
blocks over the operating
temperature range (TJ)
—
10,000
100,000
—
cycles
P/E
CC C Number of program/erase
cycles per block for 128 KB
blocks over the operating
temperature range (TJ)
—
1,000
100,000
—
cycles
Retention
CC C Minimum data retention at
85 °C average ambient
temperature1
Blocks with
0–1,000 P/E cycles
20
—
—
years
Blocks with
1,001–10,000 P/E
cycles
10
—
—
years
Blocks with
10,001–100,000 P/E
cycles
5
—
—
years
Ambient temperature averaged over duration of application, not to exceed recommended product operating
temperature range.
ECC circuitry provides correction of single bit faults and is used to improve further automotive reliability results. Some units
will experience single bit corrections throughout the life of the product with no impact to product reliability.
Table 30. Flash read access timing
Symbol
fREAD
1
C
Parameter
Conditions1
Max
Unit
2 wait states
64
MHz
C
1 wait state
40
C
0 wait states
20
CC P Maximum frequency for Flash reading
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
4.10.2
Flash power supply DC characteristics
Table 31 shows the power supply DC characteristics on external supply.
MPC5607B Microcontroller Data Sheet, Rev. 8
62
Freescale Semiconductor
Electrical characteristics
Table 31. Flash power supply DC electrical characteristics
Symbol
Value
Conditions1
Parameter
Unit
Min Typ Max
ICFREAD CC Sum of the current consumption on Flash module read
VDD_HV and VDD_BV on read access fCPU = 64 MHz
IDFREAD
ICFMOD CC Sum of the current consumption on
VDD_HV and VDD_BV on matrix
IDFMOD
modification (program/erase)
1
Code Flash
—
—
33
Data Flash
—
—
33
Program/Erase
Code Flash
on-going while reading
Data Flash
Flash registers
fCPU = 64 MHz
—
—
52
—
—
33
Code Flash
—
—
1.1
mA
Data Flash
—
—
900
µA
Code Flash
—
—
150
µA
Data Flash
—
—
150
ICFLPW CC Sum of the current consumption on
VDD_HV and VDD_BV during Flash low
IDFLPW
power mode
—
ICFPWD CC Sum of the current consumption on
VDD_HV and VDD_BV during Flash
IDFPWD
power down mode
—
mA
mA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = –40 to 125 °C, unless otherwise specified
4.10.3
Start-up/Switch-off timings
Table 32. Start-up time/Switch-off time
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ Max
tFLARSTEXIT
CC T Delay for Flash module to exit reset mode
—
—
—
125
tFLALPEXIT
CC T Delay for Flash module to exit low-power mode
—
—
—
0.5
tFLAPDEXIT
CC T Delay for Flash module to exit power-down mode
—
—
—
30
tFLALPENTRY
CC T Delay for Flash module to enter low-power mode
—
—
—
0.5
tFLAPDENTRY
CC T Delay for Flash module to enter power-down mode
—
—
—
1.5
1
µs
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
4.11
Electromagnetic compatibility (EMC) characteristics
Susceptibility tests are performed on a sample basis during product characterization.
4.11.1
Designing hardened software to avoid noise problems
EMC characterization and optimization are performed at component level with a typical application environment and simplified
MCU software. It should be noted that good EMC performance is highly dependent on the user application and the software in
particular.
Therefore it is recommended that the user apply EMC software optimization and prequalification tests in relation with the EMC
level requested for the application.
•
Software recommendations The software flowchart must include the management of runaway conditions such as:
— Corrupted program counter
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
63
Electrical characteristics
— Unexpected reset
— Critical data corruption (control registers...)
Prequalification trials Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the reset pin or the oscillator pins for 1 second.
To complete these trials, ESD stress can be applied directly on the device. When unexpected behavior is detected, the
software can be hardened to prevent unrecoverable errors occurring.
•
4.11.2
Electromagnetic interference (EMI)
The product is monitored in terms of emission based on a typical application. This emission test conforms to the IEC61967-1
standard, which specifies the general conditions for EMI measurements.
Table 33. EMI radiated emission measurement1,2
Value
Symbol
C
Parameter
Conditions
Unit
Min
—
fCPU
1
2
Max
SR — Scan range
—
0.150
SR — Operating frequency
—
—
64
—
MHz
—
—
1.28
—
V
No PLL frequency
modulation
—
—
18
dBµV
± 2% PLL frequency
modulation
—
—
14
dBµV
VDD_LV SR — LV operating voltages
SEMI
Typ
CC T Peak level
VDD = 5 V, TA = 25 °C,
LQFP144 package
Test conforming to IEC
61967-2,
fOSC = 8 MHz/fCPU =
64 MHz
1000 MHz
EMI testing and I/O port waveforms per IEC 61967-1, -2, -4
For information on conducted emission and susceptibility measurement (norm IEC 61967-4), please contact your
local marketing representative.
4.11.3
Absolute maximum ratings (electrical sensitivity)
Based on two different tests (ESD and LU) using specific measurement methods, the product is stressed in order to determine
its performance in terms of electrical sensitivity.
4.11.3.1
Electrostatic discharge (ESD)
Electrostatic discharges (a positive then a negative pulse separated by 1 second) are applied to the pins of each sample according
to each pin combination. The sample size depends on the number of supply pins in the device (3 parts(n + 1) supply pin). This
test conforms to the AEC-Q100-002/-003/-011 standard.
MPC5607B Microcontroller Data Sheet, Rev. 8
64
Freescale Semiconductor
Electrical characteristics
Table 34. ESD absolute maximum ratings1,2
Conditions
Class
Max value3
Unit
VESD(HBM) Electrostatic discharge voltage
(Human Body Model)
TA = 25 °C
conforming to AEC-Q100-002
H1C
2000
V
VESD(MM) Electrostatic discharge voltage
(Machine Model)
TA = 25 °C
conforming to AEC-Q100-003
M2
200
VESD(CDM) Electrostatic discharge voltage
(Charged Device Model)
TA = 25 °C
conforming to AEC-Q100-011
C3A
500
Symbol
Ratings
750 (corners)
1
All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated
Circuits.
2
A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device
specification requirements. Complete DC parametric and functional testing shall be performed per applicable
device specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.
3
Data based on characterization results, not tested in production
4.11.3.2
Static latch-up (LU)
Two complementary static tests are required on six parts to assess the latch-up performance:
•
•
A supply overvoltage is applied to each power supply pin.
A current injection is applied to each input, output and configurable I/O pin.
These tests are compliant with the EIA/JESD 78 IC latch-up standard.
Table 35. Latch-up results
Symbol
LU
4.12
Parameter
Static latch-up class
Conditions
TA = 125 °C
conforming to JESD 78
Class
II level A
Fast external crystal oscillator (4 to 16 MHz) electrical
characteristics
The device provides an oscillator/resonator driver. Figure 11 describes a simple model of the internal oscillator driver and
provides an example of a connection for an oscillator or a resonator.
Table 36 provides the parameter description of 4 MHz to 16 MHz crystals used for the design simulations.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
65
Electrical characteristics
EXTAL
C1
Crystal
EXTAL
XTAL
C2
DEVICE
VDD
I
R
EXTAL
XTAL
Resonator
DEVICE
XTAL
DEVICE
Notes:
1. XTAL/EXTAL must not be directly used to drive external circuits
2. A series resistor may be required, according to crystal oscillator supplier recommendations.
Figure 11. Crystal oscillator and resonator connection scheme
Table 36. Crystal description
Crystal
motional
capacitance
(Cm) fF
Crystal
motional
inductance
(Lm) mH
Load on
xtalin/xtalout
C1 = C2
(pF)1
Shunt
capacitance
between
xtalout
and xtalin
C02 (pF)
Nominal
frequency
(MHz)
NDK crystal
reference
Crystal
equivalent
series
resistance
ESR 
4
NX8045GB
300
2.68
591.0
21
2.93
8
NX5032GA
300
2.46
160.7
17
3.01
10
150
2.93
86.6
15
2.91
12
120
3.11
56.5
15
2.93
16
120
3.90
25.3
10
3.00
1
The values specified for C1 and C2 are the same as used in simulations. It should be ensured that the testing
includes all the parasitics (from the board, probe, crystal, etc.) as the AC / transient behavior depends upon them.
2 The value of C0 specified here includes 2 pF additional capacitance for parasitics (to be seen with bond-pads,
package, etc.).
MPC5607B Microcontroller Data Sheet, Rev. 8
66
Freescale Semiconductor
Electrical characteristics
S_MTRANS bit (ME_GS register)
1
0
VXTAL
1/fMXOSC
VMXOSC
90%
VMXOSCOP
10%
TMXOSCSU
valid internal clock
Figure 12. Fast external crystal oscillator (4 to 16 MHz) timing diagram
Table 37. Fast external crystal oscillator (4 to 16 MHz) electrical characteristics
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
fFXOSC
SR — Fast external crystal
oscillator frequency
—
4.0
—
16.0
MHz
gmFXOSC
CC C Fast external crystal
oscillator
transconductance
VDD = 3.3 V ± 10%,
PAD3V5V = 1
OSCILLATOR_MARGIN = 0
2.2
—
8.2
mA/V
CC P
VDD = 5.0 V ± 10%,
PAD3V5V = 0
OSCILLATOR_MARGIN = 0
2.0
—
7.4
CC C
VDD = 3.3 V ± 10%,
PAD3V5V = 1
OSCILLATOR_MARGIN = 1
2.7
—
9.7
CC C
VDD = 5.0 V ± 10%,
PAD3V5V = 0
OSCILLATOR_MARGIN = 1
2.5
—
9.2
CC T Oscillation amplitude at
EXTAL
fOSC = 4 MHz,
OSCILLATOR_MARGIN = 0
1.3
—
—
fOSC = 16 MHz,
OSCILLATOR_MARGIN = 1
1.3
—
—
—
—
0.95
—
V
—
—
2
3
mA
VFXOSC
VFXOSCOP CC C Oscillation operating point
IFXOSC2
CC T Fast external crystal
oscillator consumption
V
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
67
Electrical characteristics
Table 37. Fast external crystal oscillator (4 to 16 MHz) electrical characteristics (continued)
Symbol
tFXOSCSU
1
2
4.13
C
CC T Fast external crystal
oscillator start-up time
Value
Conditions1
Parameter
Unit
Min
Typ
Max
fOSC = 4 MHz,
OSCILLATOR_MARGIN = 0
—
—
6
fOSC = 16 MHz,
OSCILLATOR_MARGIN = 1
—
—
1.8
ms
VIH
SR P Input high level CMOS
(Schmitt Trigger)
Oscillator bypass mode
0.65VDD
—
VDD + 0.4
V
VIL
SR P Input low level CMOS
(Schmitt Trigger)
Oscillator bypass mode
0.4
—
0.35VDD
V
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified.
Stated values take into account only analog module consumption but not the digital contributor (clock tree and
enabled peripherals).
Slow external crystal oscillator (32 kHz) electrical characteristics
The device provides a low power oscillator/resonator driver.
OSC32K_EXTAL
OSC32K_EXTAL
Resonator
Crystal
C1
RP
OSC32K_XTAL
DEVICE
OSC32K_XTAL
C2
DEVICE
Note: OSC32_XTAL/OSC32_EXTAL must not be directly used to drive external circuits
Figure 13. Crystal oscillator and resonator connection scheme
MPC5607B Microcontroller Data Sheet, Rev. 8
68
Freescale Semiconductor
Electrical characteristics
l
C0
C1
Crystal
Cm
C2
Rm
Lm
C1
C2
Figure 14. Equivalent circuit of a quartz crystal
Table 38. Crystal motional characteristics1
Value
Symbol
Parameter
Conditions
Unit
Min
Typ
Max
Lm
Motional inductance
—
—
11.796
—
KH
Cm
Motional capacitance
—
—
2
—
fF
—
18
—
28
pF
k
C1/C2 Load capacitance at OSC32K_XTAL and
OSC32K_EXTAL with respect to ground2
Rm3
Motional resistance
AC coupled at C0 = 2.85 pF4
—
—
65
AC coupled at C0 = 4.9
pF4
—
—
50
AC coupled at C0 = 7.0
pF4
—
—
35
AC coupled at C0 = 9.0 pF4
—
—
30
1
The crystal used is Epson Toyocom MC306.
This is the recommended range of load capacitance at OSC32K_XTAL and OSC32K_EXTAL with respect to
ground. It includes all the parasitics due to board traces, crystal and package.
3 Maximum ESR (R ) of the crystal is 50 k
m
4
C0 Includes a parasitic capacitance of 2.0 pF between OSC32K_XTAL and OSC32K_EXTAL pins.
2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
69
Electrical characteristics
OSCON bit (OSC_CTL register)
1
0
VOSC32K_XTAL
1/fLPXOSC32K
VLPXOSC32K
90%
10%
TLPXOSC32KSU
valid internal clock
Figure 15. Slow external crystal oscillator (32 kHz) timing diagram
Table 39. Slow external crystal oscillator (32 kHz) electrical characteristics
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
fSXOSC
SR — Slow external crystal oscillator
frequency
—
32
32.768
40
kHz
VSXOSC
CC T Oscillation amplitude
—
—
2.1
—
V
ISXOSCBIAS CC T Oscillation bias current
—
2.5
µA
ISXOSC
CC T Slow external crystal oscillator
consumption
—
—
—
8
µA
tSXOSCSU
CC T Slow external crystal oscillator
start-up time
—
—
—
22
s
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified. Values are specified for no
neighbor GPIO pin activity. If oscillator is enabled (OSC32K_XTAL and OSC32K_EXTAL pins), neighboring pins
should not toggle.
2 Start-up time has been measured with EPSON TOYOCOM MC306 crystal. Variation may be seen with other crystal.
1
4.14
FMPLL electrical characteristics
The device provides a frequency modulated phase locked loop (FMPLL) module to generate a fast system clock from the main
oscillator driver.
Table 40. FMPLL electrical characteristics
Symbol
fPLLIN
C
Parameter
SR — FMPLL reference clock2
Value
Conditions1
—
Unit
Min
Typ
Max
4
—
64
MHz
MPC5607B Microcontroller Data Sheet, Rev. 8
70
Freescale Semiconductor
Electrical characteristics
Table 40. FMPLL electrical characteristics (continued)
Symbol
PLLIN
C
SR — FMPLL reference clock duty
cycle2
fPLLOUT CC P FMPLL output clock frequency
fVCO3
Value
Conditions1
Parameter
CC P VCO frequency without
frequency modulation
P VCO frequency with frequency
modulation
Unit
Min
Typ
Max
—
40
—
60
%
—
16
—
64
MHz
—
256
—
512
MHz
—
245.76
—
532.48
fCPU
SR — System clock frequency
—
—
—
64
MHz
fFREE
CC P Free-running frequency
—
20
—
150
MHz
tLOCK
CC P FMPLL lock time
40
100
µs
tSTJIT CC — FMPLL short term
Stable oscillator (fPLLIN = 16 MHz)
jitter4
tLTJIT CC — FMPLL long term jitter
IPLL
CC C FMPLL consumption
fsys maximum
–4
—
4
%
fPLLCLK at 64 MHz, 4000 cycles
—
—
10
ns
TA = 25 °C
—
—
4
mA
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
PLLIN clock retrieved directly from FXOSC clock. Input characteristics are granted when oscillator is used in
functional mode. When bypass mode is used, oscillator input clock should verify fPLLIN and PLLIN.
3 Frequency modulation is considered ± 4%.
4 Short term jitter is measured on the clock rising edge at cycle n and n+4.
1
2
4.15
Fast internal RC oscillator (16 MHz) electrical characteristics
The device provides a 16 MHz main internal RC oscillator. This is used as the default clock at the power-up of the device.
Table 41. Fast internal RC oscillator (16 MHz) electrical characteristics
Symbol
fFIRC
C
Parameter
CC P Fast internal RC oscillator high TA = 25 °C, trimmed
frequency
SR —
—
IFIRCRUN2, CC T Fast internal RC oscillator high TA = 25 °C, trimmed
frequency current in running
mode
IFIRCPWD
Value
Conditions1
CC D Fast internal RC oscillator high TA = 25 °C
frequency current in power
down mode
Unit
Min
Typ
Max
—
16
—
12
MHz
20
—
—
200
µA
—
—
10
µA
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
71
Electrical characteristics
Table 41. Fast internal RC oscillator (16 MHz) electrical characteristics (continued)
Symbol
C
Value
Conditions1
Parameter
IFIRCSTOP CC T Fast internal RC oscillator high TA = 25 °C
frequency and system clock
current in stop mode
Unit
Min
Typ
Max
sysclk = off
—
500
—
sysclk = 2 MHz
—
600
—
sysclk = 4 MHz
—
700
—
sysclk = 8 MHz
—
900
—
sysclk = 16 MHz
—
1250
—
µA
tFIRCSU
CC C Fast internal RC oscillator
start-up time
VDD = 5.0 V ± 10%
—
1.1
2.0
µs
FIRCPRE
CC C Fast internal RC oscillator
precision after software
trimming of fFIRC
TA = 25 °C
1
—
1
%
FIRCTRIM CC C Fast internal RC oscillator
trimming step
TA = 25 °C
—
1.6
5
—
FIRCVAR
CC C Fast internal RC oscillator
variation over temperature and
supply with respect to fFIRC at
TA = 25 °C in high-frequency
configuration
—
%
5
%
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
This does not include consumption linked to clock tree toggling and peripherals consumption when RC oscillator is
ON.
1
2
4.16
Slow internal RC oscillator (128 kHz) electrical characteristics
The device provides a 128 kHz low power internal RC oscillator. This can be used as the reference clock for the RTC module.
Table 42. Slow internal RC oscillator (128 kHz) electrical characteristics
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
—
128
—
100
—
150
—
—
5
µA
CC P Slow internal RC oscillator low
frequency
SR —
TA = 25 °C, trimmed
ISIRC2,
CC C Slow internal RC oscillator low
frequency current
TA = 25 °C, trimmed
tSIRCSU
CC P Slow internal RC oscillator start-up TA = 25 °C, VDD = 5.0 V ± 10%
time
—
8
12
µs
SIRCPRE
CC C Slow internal RC oscillator precision TA = 25 °C
after software trimming of fSIRC
2
—
2
%
SIRCTRIM
CC C Slow internal RC oscillator trimming
step
—
2.7
—
fSIRC
—
—
kHz
MPC5607B Microcontroller Data Sheet, Rev. 8
72
Freescale Semiconductor
Electrical characteristics
Table 42. Slow internal RC oscillator (128 kHz) electrical characteristics (continued)
Symbol
SIRCVAR
1
2
C
Parameter
Value
Conditions1
CC C Slow internal RC oscillator variation High frequency configuration
in temperature and supply with
respect to fSIRC at TA = 55 °C in high
frequency configuration
Unit
Min
Typ
Max
10
—
10
%
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified
This does not include consumption linked to clock tree toggling and peripherals consumption when RC oscillator is
ON.
4.17
4.17.1
ADC electrical characteristics
Introduction
The device provides two Successive Approximation Register (SAR) analog-to-digital converters (10-bit and 12-bit).
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
73
Electrical characteristics
Offset Error (EO)
Gain Error (EG)
1023
1022
1021
1020
1019
1 LSB ideal = VDD_ADC / 1024
1018
(2)
code out
7
(1)
6
5
(1) Example of an actual transfer curve
(5)
(2) The ideal transfer curve
4
(3) Differential non-linearity error (DNL)
(4)
(4) Integral non-linearity error (INL)
3
(5) Center of a step of the actual transfer curve
(3)
2
1
1 LSB (ideal)
0
1
2
3
4
5
6
7
1017 1018 1019 1020 1021 1022 1023
Vin(A) (LSBideal)
Offset Error (EO)
Figure 16. ADC_0 characteristic and error definitions
4.17.2
Input impedance and ADC accuracy
In the following analysis, the input circuit corresponding to the precise channels is considered.
To preserve the accuracy of the A/D converter, it is necessary that analog input pins have low AC impedance. Placing a capacitor
with good high frequency characteristics at the input pin of the device can be effective: the capacitor should be as large as
possible, ideally infinite. This capacitor contributes to attenuating the noise present on the input pin; furthermore, it sources
charge during the sampling phase, when the analog signal source is a high-impedance source.
A real filter can typically be obtained by using a series resistance with a capacitor on the input pin (simple RC filter). The RC
filtering may be limited according to the value of source impedance of the transducer or circuit supplying the analog signal to
be measured. The filter at the input pins must be designed taking into account the dynamic characteristics of the input signal
(bandwidth) and the equivalent input impedance of the ADC itself.
MPC5607B Microcontroller Data Sheet, Rev. 8
74
Freescale Semiconductor
Electrical characteristics
In fact a current sink contributor is represented by the charge sharing effects with the sampling capacitance: being CS and Cp2
substantially two switched capacitances, with a frequency equal to the conversion rate of the ADC, it can be seen as a resistive
path to ground. For instance, assuming a conversion rate of 1 MHz, with CS+Cp2 equal to 3 pF, a resistance of 330 k is
obtained (REQ = 1 / (fc × (CS+Cp2)), where fc represents the conversion rate at the considered channel). To minimize the error
induced by the voltage partitioning between this resistance (sampled voltage on CS+Cp2) and the sum of RS + RF, the external
circuit must be designed to respect the Equation 4:
Eqn. 4
RS + RF
1
V A  ---------------------  --- LSB
R EQ
2
Equation 4 generates a constraint for external network design, in particular on a resistive path.
EXTERNAL CIRCUIT
INTERNAL CIRCUIT SCHEME
VDD
Source
RS
VA
Filter
RF
Current Limiter
RL
CF
Channel
Selection
Sampling
RSW1
RAD
CP1
CP2
CS
RS Source Impedance
RF Filter Resistance
CF Filter Capacitance
Current Limiter Resistance
RL
RSW1 Channel Selection Switch Impedance
RAD Sampling Switch Impedance
CP Pin Capacitance (two contributions, CP1 and CP2)
CS Sampling Capacitance
Figure 17. Input equivalent circuit (precise channels)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
75
Electrical characteristics
EXTERNAL CIRCUIT
INTERNAL CIRCUIT SCHEME
VDD
Source
RS
Filter
RF
Current Limiter
RL
CF
VA
RS
RF
CF
RL
RSW
RAD
CP
CS
CP1
Channel
Selection
Extended
Switch
Sampling
RSW1
RSW2
RAD
CP3
CP2
CS
Source Impedance
Filter Resistance
Filter Capacitance
Current Limiter Resistance
Channel Selection Switch Impedance (two contributions RSW1 and RSW2)
Sampling Switch Impedance
Pin Capacitance (three contributions, CP1, CP2 and CP3)
Sampling Capacitance
Figure 18. Input equivalent circuit (extended channels)
A second aspect involving the capacitance network shall be considered. Assuming the three capacitances CF, CP1 and CP2 are
initially charged at the source voltage VA (refer to the equivalent circuit reported in Figure 17): A charge sharing phenomenon
is installed when the sampling phase is started (A/D switch close).
Voltage Transient on CS
VCS
VA
VA2
V <0.5 LSB
1
2
1 < (RSW + RAD) CS << tS
2 = RL (CS + CP1 + CP2)
VA1
TS
t
Figure 19. Transient behavior during sampling phase
In particular two different transient periods can be distinguished:
1.
A first and quick charge transfer from the internal capacitance CP1 and CP2 to the sampling capacitance CS occurs (CS
is supposed initially completely discharged): considering a worst case (since the time constant in reality would be
faster) in which CP2 is reported in parallel to CP1 (call CP = CP1 + CP2), the two capacitances CP and CS are in series,
and the time constant is
MPC5607B Microcontroller Data Sheet, Rev. 8
76
Freescale Semiconductor
Electrical characteristics
CP  CS
 1 =  R SW + R AD   --------------------CP + CS
Eqn. 5
Equation 5 can again be simplified considering only CS as an additional worst condition. In reality, the transient is
faster, but the A/D converter circuitry has been designed to be robust also in the very worst case: the sampling time tS
is always much longer than the internal time constant:
Eqn. 6
 1   R SW + R AD   C S « t s
The charge of CP1 and CP2 is redistributed also on CS, determining a new value of the voltage VA1 on the capacitance
according to Equation 7:
Eqn. 7
V A1   C S + C P1 + C P2  = V A   C P1 + C P2 
2.
A second charge transfer involves also CF (that is typically bigger than the on-chip capacitance) through the resistance
RL: again considering the worst case in which CP2 and CS were in parallel to CP1 (since the time constant in reality
would be faster), the time constant is:
Eqn. 8
 2  R L   C S + C P1 + C P2 
In this case, the time constant depends on the external circuit: in particular imposing that the transient is completed
well before the end of sampling time ts, a constraints on RL sizing is obtained:
ADC_0 (10-bit)
8.5   = 8.5  R   C + C
2
L
S
Eqn. 9
P1 + C P2   t s
ADC_1 (12-bit)
10   2 = 10  R L   C S + C P1 + C P2   t s
Eqn. 10
Of course, RL shall be sized also according to the current limitation constraints, in combination with RS (source
impedance) and RF (filter resistance). Being CF definitively bigger than CP1, CP2 and CS, then the final voltage VA2
(at the end of the charge transfer transient) will be much higher than VA1. Equation 11 must be respected (charge
balance assuming now CS already charged at VA1):
Eqn. 11
VA2   C S + C P1 + C P2 + C F  = V A  C F + V A1   C P1 + C P2 + C S 
The two transients above are not influenced by the voltage source that, due to the presence of the RFCF filter, is not able to
provide the extra charge to compensate the voltage drop on CS with respect to the ideal source VA; the time constant RFCF of
the filter is very high with respect to the sampling time (ts). The filter is typically designed to act as antialiasing.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
77
Electrical characteristics
Analog source bandwidth (VA)
tc < 2 RFCF (Conversion rate vs. filter pole)
Noise
fF = f0 (Anti-aliasing filtering condition)
2 f0 < fC (Nyquist)
f0
f
Anti-aliasing filter (fF = RC filter pole)
fF
f
Sampled signal spectrum (fC = Conversion rate)
f0
fC
f
Figure 20. Spectral representation of input signal
Calling f0 the bandwidth of the source signal (and as a consequence the cut-off frequency of the antialiasing filter, fF), according
to the Nyquist theorem the conversion rate fC must be at least 2f0; it means that the constant time of the filter is greater than or
at least equal to twice the conversion period (tc). Again the conversion period tc is longer than the sampling time ts, which is
just a portion of it, even when fixed channel continuous conversion mode is selected (fastest conversion rate at a specific
channel): in conclusion it is evident that the time constant of the filter RFCF is definitively much higher than the sampling time
ts, so the charge level on CS cannot be modified by the analog signal source during the time in which the sampling switch is
closed.
The considerations above lead to impose new constraints on the external circuit, to reduce the accuracy error due to the voltage
drop on CS; from the two charge balance equations above, it is simple to derive Equation 12 between the ideal and real sampled
voltage on CS:
Eqn. 12
V A2
C P1 + C P2 + C F
------------ = ------------------------------------------------------VA
C P1 + C P2 + C F + C S
From this formula, in the worst case (when VA is maximum, that is for instance 5 V), assuming to accept a maximum error of
half a count, a constraint is evident on CF value:
ADC_0 (10-bit)
Eqn. 13
C F  2048  C S
ADC_1 (12-bit)
Eqn. 14
C F  8192  C S
MPC5607B Microcontroller Data Sheet, Rev. 8
78
Freescale Semiconductor
Electrical characteristics
4.17.3
ADC electrical characteristics
Table 43. ADC input leakage current
Value
Symbol C
Parameter
Conditions
Unit
Min
Typ
Max
—
1
70
—
1
70
3
100
ILKG CC D Input leakage current TA = 40 °C No current injection on adjacent pin
D
TA = 25 °C
D
TA = 85 °C
D
TA = 105 °C
—
8
200
P
TA = 125 °C
—
45
400
nA
Table 44. ADC_0 conversion characteristics (10-bit ADC_0)
Symbol
C
Parameter
Value
Conditions1
Unit
Min
Typ
Max
VSS_ADC0 SR — Voltage on VSS_HV_ADC0
(ADC_0 reference) pin with
respect to ground (VSS)2
—
0.1
—
0.1
V
VDD_ADC0 SR — Voltage on VDD_HV_ADC pin
(ADC reference) with respect
to ground (VSS)
—
VDD  0.1
—
VDD + 0.1
V
—
VSS_ADC0
 0.1
—
VDD_ADC0
+ 0.1
V
IADC0pwd SR — ADC_0 consumption in power
down mode
—
—
—
50
µA
IADC0run SR — ADC_0 consumption in
running mode
—
—
—
5
mA
—
6
—
14
45
—
55
%
—
—
—
1.5
µs
fADC = 32 MHz,
INPSAMP = 17
0.5
—
fADC = 6 MHz,
INPSAMP = 255
—
—
42
fADC = 32 MHz,
INPCMP = 2
0.625
—
—
µs
VAINx
fADC0
SR — Analog input voltage3
SR — ADC_0 analog frequency
ADC0_SYS SR — ADC_0 digital clock duty cycle ADCLKSEL =
(ipg_clk)
tADC0_PU SR — ADC_0 power up delay
tADC0_S CC T Sampling
time5
tADC0_C CC P Conversion time6
32 + 4% MHz
µs
CS
CC D ADC_0 input sampling
capacitance
—
—
—
3
pF
CP1
CC D ADC_0 input pin capacitance 1
—
—
—
3
pF
CP2
CC D ADC_0 input pin capacitance 2
—
—
—
1
pF
CP3
CC D ADC_0 input pin capacitance 3
—
—
—
1
pF
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
79
Electrical characteristics
Table 44. ADC_0 conversion characteristics (10-bit ADC_0) (continued)
Symbol
3
4
5
6
7
Value
Conditions1
Unit
Min
Typ
Max
CC D Internal resistance of analog
source
—
—
—
3
k
RSW2
CC D Internal resistance of analog
source
—
—
—
2
k
RAD
CC D Internal resistance of analog
source
—
—
—
2
k
IINJ
SR — Input current Injection
VDD =
3.3 V ± 10%
5
—
5
mA
VDD =
5.0 V ± 10%
5
—
5
Current injection
on one ADC_0
input, different
from the
converted one
| INL |
CC T Absolute integral nonlinearity No overload
—
0.5
1.5
LSB
| DNL |
CC T Absolute differential
nonlinearity
—
0.5
1.0
LSB
| EO |
CC T Absolute offset error
—
—
0.5
—
LSB
| EG |
CC T Absolute gain error
—
—
0.6
—
LSB
LSB
TUEX
2
Parameter
RSW1
TUEP
1
C
No overload
CC P Total unadjusted
for
precise channels, input only
T
pins
Without current injection
2
0.6
2
With current injection
3
—
3
CC T Total unadjusted error7 for
extended channel
T
Without current injection
3
1
3
With current injection
4
error7
LSB
4
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified.
Analog and digital VSS must be common (to be tied together externally).
VAINx may exceed VSS_ADC0 and VDD_ADC0 limits, remaining on absolute maximum ratings, but the results of the
conversion will be clamped respectively to 0x000 or 0x3FF.
Duty cycle is ensured by using system clock without prescaling. When ADCLKSEL = 0, the duty cycle is ensured
by internal divider by 2.
During the sampling time the input capacitance CS can be charged/discharged by the external source. The internal
resistance of the analog source must allow the capacitance to reach its final voltage level within t ADC0_S. After the
end of the sampling time tADC0_S, changes of the analog input voltage have no effect on the conversion result.
Values for the sampling clock tADC0_S depend on programming.
This parameter does not include the sampling time tADC0_S, but only the time for determining the digital result and
the time to load the result’s register with the conversion result.
Total Unadjusted Error: The maximum error that occurs without adjusting Offset and Gain errors. This error is a
combination of Offset, Gain and Integral Linearity errors.
MPC5607B Microcontroller Data Sheet, Rev. 8
80
Freescale Semiconductor
Electrical characteristics
Gain Error (EG)
Offset Error (EO)
4095
4094
4093
4092
4091
1 LSB ideal = VDD_ADC / 4096
4090
(2)
code out
7
(1)
6
5
(1) Example of an actual transfer curve
(5)
(2) The ideal transfer curve
4
(3) Differential non-linearity error (DNL)
(4)
(4) Integral non-linearity error (INL)
3
(5) Center of a step of the actual transfer curve
(3)
2
1
1 LSB (ideal)
0
1
2
3
4
5
6
7
4090 4091 4092 4093 4094 4095
Vin(A) (LSBideal)
Offset Error (EO)
Figure 21. ADC_1 characteristic and error definitions
Table 45. ADC_1 conversion characteristics (12-bit ADC_1)
Symbol
C
Parameter
Value
Conditions1
VSS_ADC1 SR — Voltage on VSS_HV_ADC1
(ADC_1 reference) pin with
respect to ground (VSS)2
—
VDD_ADC1 SR — Voltage on VDD_HV_ADC1 pin
(ADC_1 reference) with
respect to ground (VSS)
—
Unit
Min
Typ
Max
–0.1
—
0.1
V
VDD + 0.1
V
VDD – 0.1 —
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
81
Electrical characteristics
Table 45. ADC_1 conversion characteristics (12-bit ADC_1) (continued)
Symbol
C
Parameter
Value
Conditions1
Unit
Min
VAINx
SR — Analog input voltage3
—
Typ
VSS_ADC1 —
– 0.1
Max
VDD_ADC1
+ 0.1
V
IADC1pwd SR — ADC_1 consumption in power
down mode
—
—
—
50
µA
IADC1run
—
—
—
6
mA
VDD = 3.3 V
3.33
—
20 + 4%
MHz
VDD = 5 V
3.33
—
32 + 4%
—
—
—
1.5
µs
ns
fADC1
SR — ADC_1 consumption in running
mode
SR — ADC_1 analog frequency
tADC1_PU SR — ADC_1 power up delay
tADC1_S
tADC1_C
time4
fADC1 = 20 MHz,
INPSAMP = 12
600
—
—
Sampling time4
VDD = 5.0 V
fADC1 = 32 MHz,
INPSAMP = 17
500
—
—
Sampling time4
VDD = 3.3 V
fADC1 = 3.33 MHz,
INPSAMP = 255
—
—
76.2
Sampling time4
VDD = 5.0 V
fADC1 = 3.33 MHz,
INPSAMP = 255
—
—
76.2
CC P Conversion time5
VDD = 3.3 V
fADC1 = 20 MHz,
INPCMP = 0
2.4
—
—
µs
Conversion time5
VDD = 5.0 V
fADC 1 = 32 MHz,
INPCMP = 0
1.5
—
—
µs
Conversion time5
VDD = 3.3 V
fADC 1 = 13.33 MHz,
INPCMP = 0
—
—
3.6
µs
Conversion time5
VDD = 5.0 V
fADC1 = 13.33 MHz,
INPCMP = 0
—
—
3.6
µs
45
—
55
%
CC T Sampling
VDD = 3.3 V
ADC1_SYS SR — ADC_1 digital clock duty cycle ADCLKSEL = 16
µs
CS
CC D ADC_1 input sampling
capacitance
—
—
—
5
pF
CP1
CC D ADC_1 input pin capacitance 1
—
—
—
3
pF
CP2
CC D ADC_1 input pin capacitance 2
—
—
—
1
pF
CP3
CC D ADC_1 input pin capacitance 3
—
—
—
1.5
pF
RSW1
CC D Internal resistance of analog
source
—
—
—
1
k
RSW2
CC D Internal resistance of analog
source
—
—
—
2
k
RAD
CC D Internal resistance of analog
source
—
—
—
0.3
k
MPC5607B Microcontroller Data Sheet, Rev. 8
82
Freescale Semiconductor
Electrical characteristics
Table 45. ADC_1 conversion characteristics (12-bit ADC_1) (continued)
Symbol
IINJ
3
4
5
6
7
SR — Input current Injection
Value
Conditions1
Current
VDD = 3.3 V ± 10%
injection on
VDD = 5.0 V ± 10%
one ADC_1
input, different
from the
converted one
Unit
Min
Typ
Max
–5
—
5
–5
—
5
mA
CC T Absolute integral nonlinearity – No overload
Precise channels
—
1
3
LSB
| INLX |
CC T Absolute integral nonlinearity – No overload
Extended channels
—
1.5
5
LSB
| DNL |
CC T Absolute differential
nonlinearity
—
0.5
1
LSB
| EO |
CC T Absolute offset error
—
—
2
—
LSB
| EG |
CC T Absolute gain error
—
—
2
—
LSB
LSB
TUEX7
2
Parameter
| INLP |
TUEP7
1
C
No overload
CC P Total unadjusted error for
precise channels, input only
T
pins
Without current injection
–6
—
6
With current injection
–8
—
8
CC T Total unadjusted error for
extended channel
T
Without current injection
–10
—
10
With current injection
–12
—
12
LSB
VDD = 3.3 V ± 10% / 5.0 V ± 10%, TA = –40 to 125 °C, unless otherwise specified
Analog and digital VSS must be common (to be tied together externally).
VAINx may exceed VSS_ADC1 and VDD_ADC1 limits, remaining on absolute maximum ratings, but the results of the
conversion will be clamped respectively to 0x000 or 0xFFF.
During the sampling time the input capacitance CS can be charged/discharged by the external source. The internal
resistance of the analog source must allow the capacitance to reach its final voltage level within tADC1_S. After the end
of the sampling time tADC1_S, changes of the analog input voltage have no effect on the conversion result. Values for
the sampling clock tADC1_S depend on programming.
This parameter does not include the sampling time tADC1_S, but only the time for determining the digital result and the
time to load the result’s register with the conversion result.
Duty cycle is ensured by using system clock without prescaling. When ADCLKSEL = 0, the duty cycle is ensured by
internal divider by 2.
Total Unadjusted Error: The maximum error that occurs without adjusting Offset and Gain errors. This error is a
combination of Offset, Gain and Integral Linearity errors.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
83
Electrical characteristics
4.18
On-chip peripherals
4.18.1
Current consumption
Table 46. On-chip peripherals current consumption1
Symbol
C
Parameter
IDD_BV(CAN) CC T CAN (FlexCAN)
supply current on
VDD_BV
Typical value2 Unit
Conditions
Bitrate:
500 Kbyte/s
Bitrate:
125 Kbyte/s
Total (static + dynamic)
8 * fperiph + 85
consumption:
• FlexCAN in loop-back
8 * fperiph + 27
mode
• XTAL at 8 MHz used as
CAN engine clock source
• Message sending period is
580 µs
IDD_BV(eMIOS) CC T eMIOS supply current Static consumption:
on VDD_BV
• eMIOS channel OFF
• Global prescaler enabled
29 * fperiph
Dynamic consumption:
• It does not change varying the frequency
(0.003 mA)
IDD_BV(SCI)
CC T SCI (LINFlex) supply
current on VDD_BV
Total (static + dynamic) consumption:
• LIN mode
• Baudrate: 20 Kbyte/s
IDD_BV(SPI)
CC T SPI (DSPI) supply
current on VDD_BV
IDD_BV
(ADC_0/ADC_1)
µA
3
5 * fperiph + 31
µA
Ballast static consumption (only clocked)
1
µA
Ballast dynamic consumption (continuous
communication):
• Baudrate: 2 Mbit/s
• Transmission every 8 µs
• Frame: 16 bits
16 * fperiph
CC T ADC_0/ADC_1 supply VDD = 5.5 V
current on VDD_BV
IDD_HV_ADC0 CC T ADC_0 supply current VDD = 5.5 V
on VDD_HV_ADC0
Ballast static consumption
(no conversion)3
41 * fperiph
Ballast dynamic consumption
(continuous conversion)3
46 * fperiph
Analog static consumption
(no conversion)
µA
200
µA
3
mA
300 * fperiph
µA
Analog dynamic consumption
(continuous conversion)
4
mA
VDD = 5.5 V
—
12
mA
CC T PLL supply current on VDD = 5.5 V
VDD_HV
—
30 * fperiph
µA
Analog dynamic consumption
(continuous conversion)
IDD_HV_ADC1 CC T ADC_1 supply current VDD = 5.5 V
on VDD_HV_ADC1
IDD_HV(FLASH) CC T CFlash + DFlash
supply current on
VDD_HV
IDD_HV(PLL)
µA
Analog static consumption
(no conversion)
MPC5607B Microcontroller Data Sheet, Rev. 8
84
Freescale Semiconductor
Electrical characteristics
1
Operating conditions: TA = 25 °C, fperiph = 8 MHz to 64 MHz
fperiph is an absolute value.
3
During the conversion, the total current consumption is given from the sum of the static and dynamic consumption,
i.e., (41 + 46) * fperiph.
2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
85
86
4.18.2
DSPI characteristics
DSPI0/DSPI1/DSPI3/DSPI5
No.
1
Symbol
tSCK
C
DSPI2/DSPI4
Parameter
Unit
MPC5607B Microcontroller Data Sheet, Rev. 8
Min
Typ
Max
Min
Typ
Max
Master mode
(MTFE = 0)
125
—
—
333
—
—
D
Slave mode
(MTFE = 0)
125
—
—
333
—
—
D
Master mode
(MTFE = 1)
83
—
—
125
—
—
D
Slave mode
(MTFE = 1)
83
—
—
125
—
—
—
—
fCPU
—
—
fCPU
MHz
—
—
153
ns
SR D SCK cycle time
ns
—
fDSPI
—
tCSC
CC D Internal delay between pad Master mode
associated to SCK and pad
associated to CSn in
master mode for CSn1->0
—
—
1302
—
tASC
CC D Internal delay between pad Master mode
associated to SCK and pad
associated to CSn in
master mode for CSn1->1
—
—
1303
—
—
1303
ns
SR D DSPI digital controller frequency
2
tCSCext4 SR D CS to SCK delay
Slave mode
32
—
—
32
—
—
ns
3
tASCext5 SR D After SCK delay
Slave mode
1/fDSPI + 5
—
—
1/fDSPI + 5
—
—
ns
—
tSCK/2
—
—
tSCK/2
—
ns
4
tSDC
CC D SCK duty cycle
Master mode
SR D
Slave mode
tSCK/2
—
—
tSCK/2
—
—
Freescale Semiconductor
5
tA
SR D Slave access time
Slave mode
—
—
1/fDSPI + 70
—
—
1/fDSPI + 130
ns
6
tDI
SR D Slave SOUT disable time
Slave mode
7
—
—
7
—
—
ns
7
tPCSC
SR D PCSx to PCSS time
—
0
—
—
0
—
—
ns
8
tPASC
SR D PCSS to PCSx time
—
0
—
—
0
—
—
ns
9
tSUI
43
—
—
145
—
—
ns
5
—
—
5
—
—
SR D Data setup time for inputs Master mode
Slave mode
Electrical characteristics
Table 47. DSPI characteristics1
Freescale Semiconductor
Table 47. DSPI characteristics1 (continued)
DSPI0/DSPI1/DSPI3/DSPI5
No.
10
Symbol
tHI
11
tSUO7
12
tHO7
C
SR D Data hold time for inputs
Unit
Min
Typ
Max
Min
Typ
Max
Master mode
0
—
—
0
—
—
Slave mode
26
—
—
26
—
—
—
—
32
—
—
50
—
—
52
—
—
160
0
—
—
0
—
—
8
—
—
13
—
—
CC D Data valid after SCK edge Master mode
Slave mode
CC D Data hold time for outputs Master mode
Slave mode
MPC5607B Microcontroller Data Sheet, Rev. 8
1
2
3
4
5
6
7
DSPI2/DSPI4
Parameter
ns
ns
ns
Operating conditions: CL = 10 to 50 pF, SlewIN = 3.5 to 15 ns
Maximum value is reached when CSn pad is configured as SLOW pad while SCK pad is configured as MEDIUM. A positive value means that SCK
starts before CSn is asserted. DSPI2 has only SLOW SCK available.
Maximum value is reached when CSn pad is configured as MEDIUM pad while SCK pad is configured as SLOW. A positive value means that CSn is
deasserted before SCK. DSPI0 and DSPI1 have only MEDIUM SCK available.
The tCSC delay value is configurable through a register. When configuring tCSC (using PCSSCK and CSSCK fields in DSPI_CTARx registers), delay
between internal CS and internal SCK must be higher than tCSC to ensure positive tCSCext.
The tASC delay value is configurable through a register. When configuring tASC (using PASC and ASC fields in DSPI_CTARx registers), delay between
internal CS and internal SCK must be higher than tASC to ensure positive tASCext.
This delay value corresponds to SMPL_PT = 00b which is bit field 9 and 8 of DSPI_MCR register.
SCK and SOUT are configured as MEDIUM pad.
Electrical characteristics
87
Electrical characteristics
Figure 22. DSPI classic SPI timing — master, CPHA = 0
2
3
PCSx
1
4
SCK Output
(CPOL = 0)
4
SCK Output
(CPOL = 1)
9
SIN
10
First Data
Last Data
Data
12
SOUT
First Data
11
Data
Last Data
Note: Numbers shown reference Table 46.
Figure 23. DSPI classic SPI timing — master, CPHA = 1
PCSx
SCK Output
(CPOL = 0)
10
SCK Output
(CPOL = 1)
9
SIN
Data
First Data
12
SOUT
First Data
Last Data
11
Data
Last Data
Note: Numbers shown reference Table 46.
MPC5607B Microcontroller Data Sheet, Rev. 8
88
Freescale Semiconductor
Electrical characteristics
Figure 24. DSPI classic SPI timing — slave, CPHA = 0
3
2
SS
1
4
SCK Input
(CPOL = 0)
4
SCK Input
(CPOL = 1)
5
First Data
SOUT
9
6
Data
Last Data
Data
Last Data
10
First Data
SIN
11
12
Note: Numbers shown reference Table 46.
Figure 25. DSPI classic SPI timing — slave, CPHA = 1
SS
SCK Input
(CPOL = 0)
SCK Input
(CPOL = 1)
11
5
12
SOUT
First Data
9
SIN
Data
Last Data
Data
Last Data
6
10
First Data
Note: Numbers shown reference Table 46.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
89
Electrical characteristics
Figure 26. DSPI modified transfer format timing — master, CPHA = 0
3
PCSx
4
1
2
SCK Output
(CPOL = 0)
4
SCK Output
(CPOL = 1)
9
SIN
10
First Data
Last Data
Data
12
SOUT
11
First Data
Last Data
Data
Note: Numbers shown reference Table 46.
Figure 27. DSPI modified transfer format timing — master, CPHA = 1
PCSx
SCK Output
(CPOL = 0)
SCK Output
(CPOL = 1)
10
9
SIN
First Data
Data
12
SOUT
First Data
Data
Last Data
11
Last Data
Note: Numbers shown reference Table 46.
MPC5607B Microcontroller Data Sheet, Rev. 8
90
Freescale Semiconductor
Electrical characteristics
Figure 28. DSPI modified transfer format timing — slave, CPHA = 0
3
2
SS
1
SCK Input
(CPOL = 0)
4
4
SCK Input
(CPOL = 1)
First Data
SOUT
Data
6
Last Data
10
9
Data
First Data
SIN
12
11
5
Last Data
Note: Numbers shown reference Table 46.
Figure 29. DSPI modified transfer format timing — slave, CPHA = 1
SS
SCK Input
(CPOL = 0)
SCK Input
(CPOL = 1)
11
5
12
First Data
SOUT
9
SIN
Data
Last Data
Data
Last Data
6
10
First Data
Note: Numbers shown reference Table 46.
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
91
Electrical characteristics
8
7
PCSS
PCSx
Note: Numbers shown reference Table 46.
Figure 30. DSPI PCS strobe (PCSS) timing
4.18.3
Nexus characteristics
Table 48. Nexus characteristics
Value
No.
Symbol
C
Parameter
Unit
Min
Typ
Max
1
tTCYC
CC D TCK cycle time
64
—
—
ns
2
tMCYC
CC D MCKO cycle time
32
—
—
ns
3
tMDOV
CC D MCKO low to MDO data valid
—
—
8
ns
4
tMSEOV
CC D MCKO low to MSEO_b data valid
—
—
8
ns
5
tEVTOV
CC D MCKO low to EVTO data valid
—
—
8
ns
6
tNTDIS
CC D TDI data setup time
15
—
—
ns
tNTMSS
CC D TMS data setup time
15
—
—
ns
tNTDIH
CC D TDI data hold time
5
—
—
ns
tNTMSH
CC D TMS data hold time
5
—
—
ns
7
8
tTDOV
CC D TCK low to TDO data valid
35
—
—
ns
9
tTDOI
CC D TCK low to TDO data invalid
6
—
—
ns
MPC5607B Microcontroller Data Sheet, Rev. 8
92
Freescale Semiconductor
Electrical characteristics
TCK
10
11
TMS, TDI
12
TDO
Note: Numbers shown reference Table 48.
Figure 31. Nexus TDI, TMS, TDO timing
4.18.4
JTAG characteristics
Table 49. JTAG characteristics
Value
No.
Symbol
C
Parameter
Unit
Min
Typ
Max
1
tJCYC
CC
D TCK cycle time
64
—
—
ns
2
tTDIS
CC
D TDI setup time
15
—
—
ns
3
tTDIH
CC
D TDI hold time
5
—
—
ns
4
tTMSS
CC
D TMS setup time
15
—
—
ns
5
tTMSH
CC
D TMS hold time
5
—
—
ns
6
tTDOV
CC
D TCK low to TDO valid
—
—
33
ns
7
tTDOI
CC
D TCK low to TDO invalid
6
—
—
ns
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
93
Electrical characteristics
TCK
2/4
DATA INPUTS
3/5
INPUT DATA VALID
6
DATA OUTPUTS
OUTPUT DATA VALID
7
DATA OUTPUTS
Note: Numbers shown reference Table 49.
Figure 32. Timing diagram — JTAG boundary scan
MPC5607B Microcontroller Data Sheet, Rev. 8
94
Freescale Semiconductor
Package characteristics
5
Package characteristics
5.1
Package mechanical data
5.1.1
176 LQFP
Figure 33. 176 LQFP package mechanical drawing (Part 1 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
95
Package characteristics
Figure 34. 176 LQFP package mechanical drawing (Part 2 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
96
Freescale Semiconductor
Package characteristics
Figure 35. 176 LQFP package mechanical drawing (Part 3 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
97
Package characteristics
5.1.2
144 LQFP
Figure 36. 144 LQFP package mechanical drawing (Part 1 of 2)
MPC5607B Microcontroller Data Sheet, Rev. 8
98
Freescale Semiconductor
Package characteristics
Figure 37. 144 LQFP package mechanical drawing (Part 2 of 2)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
99
Package characteristics
5.1.3
100 LQFP
Figure 38. 100 LQFP package mechanical drawing (Part 1 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
100
Freescale Semiconductor
Package characteristics
Figure 39. 100 LQFP package mechanical drawing (Part 2 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
101
Package characteristics
Figure 40. 100 LQFP package mechanical drawing (Part 3 of 3)
MPC5607B Microcontroller Data Sheet, Rev. 8
102
Freescale Semiconductor
Package characteristics
5.1.4
208 MAPBGA
Figure 41. 208 MAPBGA package mechanical drawing (Part 1 of 2)
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
103
Package characteristics
Figure 42. 208 MAPBGA package mechanical drawing (Part 2 of 2)
MPC5607B Microcontroller Data Sheet, Rev. 8
104
Freescale Semiconductor
Ordering information
6
Ordering information
Figure 43. Commercial product code structure
Example code:
M
PC
56
0
7
B
F1A
M
LL
6
R
Qualification Status
Power Architecture Core
Automotive Platform
Core Version
Flash Size (core dependent)
Product
Fab and Mask Indicator
Temperature spec.
Package Code
Frequency
R = Tape & Reel (blank if Tray)
1
Qualification Status
M = general market qualified
S = Automotive qualified
P = Engineering samples
Flash Size (for z0 core)
5 = 768 KB
6 = 1024 KB
7 = 1.5 MB
Temperature spec.
C = -40 to 85 °C
V = -40 to 105 °C
M = -40 to 125 °C
Automotive Platform
56 = PPC in 90nm
Product
B = Body
Core Version
0 = e200z0
Fab and Mask Indicator
F = ATMC Fab
K = TSMC Fab
0 = Version of the maskset
A = Mask set indicator (Blank = 1st
production maskset, A = 2nd,
Package Code
LL = 100 LQFP
LQ = 144 LQFP
LU = 176 LQFP
MG = 208 MAPBGA1
Frequency
4 = Up to 48 MHz
6 = Up to 64 MHz
208 MAPBGA is available only as development package for Nexus2+.
Appendix A Abbreviations
Table 50 lists abbreviations used but not defined elsewhere in this document.
Table 50. Abbreviations
Abbreviation
Meaning
CMOS
Complementary metal oxide semiconductor
CPHA
Clock phase
CPOL
Clock polarity
CS
Peripheral chip select
EVTO
Event out
MCKO
Message clock out
MDO
Message data out
MSEO
Message start/end out
MTFE
Modified timing format enable
SCK
Serial communications clock
SOUT
Serial data out
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
105
Abbreviations
Table 50. Abbreviations (continued)
Abbreviation
Meaning
TBD
To be defined
TCK
Test clock input
TDI
Test data input
TDO
Test data output
TMS
Test mode select
MPC5607B Microcontroller Data Sheet, Rev. 8
106
Freescale Semiconductor
Revision history
7
Revision history
Table 51 summarizes revisions to this document.
Table 51. Revision history
Revision
Date
Substantive changes
1
12-Jan-2009 Initial release
2
09 Nov-2009 Updated Features
Replaced 27 IRQs in place of 23
ADC features
External Ballast resistor support conditions
Updated device summary-added 208 BGA details
Updated block diagram to include WKUP
Updated block diagram to include 5 ch ADC 12 -bit
Updated Block summary table
Updated LQFP 144, 176 and 100 pinouts. Applied new naming convention for ADC
signals as ADCx_P[x] and ADCx_S[x]
Section 1, “General description
Updated MPC5607B device comparison table
Updated block diagram-aligned with 512k
Updated block summary-aligned with 512k
Section 2, “Package pinouts
Updated 100,144,176,208 packages according to cut2.0 changes
Added Section 3.5.1, “External ballast resistor recommendations
Added NVUSRO [WATCHDOG_EN] field description
Updated Absolute maximum ratings
Updated LQFP thermal characteristics
Updated I/O supply segments
Updated Voltage regulator capacitance connection
Updated Low voltage monitor electrical characteristics
Updated Low voltage power domain electrical characteristics
Updated DC electrical characteristics
Updated Program/Erase specifications
Updated Conversion characteristics (10 bit ADC)
Updated FMPLL electrical characteristics
Updated Fast RC oscillator electrical characteristics-aligned with MPC5604B
Updated On-chip peripherals current consumption
Updated ADC characteristics and error definitions diagram
Updated ADC conversion characteristics (10 bit and 12 bit)
Added ADC characteristics and error definitions diagram for 12 bit ADC
3
25 Jan-2010 Updated Features
Updated block diagram to connect peripherals to pad I/O
Updated block summary to include ADC 12-bit
Updated 144, 176 and 100 pinouts to adjust format issues
Table 26 Flash module life-retention value changed from 1-5 to 5 yrs
Minor editing changes
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
107
Revision history
Table 51. Revision history (continued)
Revision
4
Date
Substantive changes
24 Aug 2010 Editorial changes and improvements.
Updated “Features“ section
Table 1: updated footnote concerning 208 MAPBGA
In the block diagram:
• Added “5ch 12-bit ADC“ block.
• Updated Legend.
• Added “Interrupt request with wakeup functionality” as an input to the WKPU block.
Figure 2: removed alternate functions
Figure 3: removed alternate functions
Figure 4: removed alternate functions
Table 2: added contents concerning the following blocks: CMU, eDMA, ECSM, MC_ME,
MC_PCU, NMI, SSCM, SWT and WKPU
Added Section 3.2, Pin muxing
Section 4, Electrical characteristics: removed “Caution” note
Section 4.2, NVUSRO register: removed “NVUSRO[WATCHDOG_EN] field description“
section
Table 11: VIN: removed min value in “relative to VDD” row
Table 12
• TA C-Grade Part, TJ C-Grade Part, TA V-Grade Part, TJ V-Grade Part, TA M-Grade Part, TJ M-Grade Part:
added new rows
• TVDD: contents merged into one row
• VDD_BV: changed min value in “relative to VDD” row
Section 4.5, Thermal characteristics
• Section 4.5.1, External ballast resistor recommendations: added new paragraph about
power supply
• Table 14: added RJB and RJC rows
• Removed “208 MAPBGA thermal characteristics” table
Table 15: rewrote parameter description of WFI and WNFI
Section 4.6.5, I/O pad current specification
• Removed IDYNSEG information
• Updated “I/O supply segments” table
Table 22: removed IDYNSEG row
Added Table 23
Table 25
• Updated all values
• Removed IVREGREF and IVREDLVD12 rows
• Added the footnote “The duration of the in-rush current depends on the capacitance
placed on LV pins. BV decaps must be sized accordingly. Refer to IMREG value for
minimum amount of current to be provided in cc.” to the IDD_BV specification.
Table 26
• Updated VPORH min/max value
• Updated VLVDLVCORL min value
Updated Table 27
Table 28
• Tdwprogram: added initial max value
• Inserted Teslat row
Table 29: removed the “To be confirmed” footnote
In the “Crystal oscillator and resonator connection scheme” figure, removed RP.
Table 39
• Removed gmSXOSC row
• ISXOSCBIAS: added min/typ/max value
MPC5607B Microcontroller Data Sheet, Rev. 8
108
Freescale Semiconductor
Revision history
Table 51. Revision history (continued)
Revision
4
(cont.)
Date
Substantive changes
24 Aug 2010 Table 40:
(cont.)
• Added fVCO row
• Added tSTJIT row
Table 41
• IFIRCPWD: removed row for TA = 55 °C
• Updated TFIRCSU row
Table 44: Added two rows: IADC0pwd and IADC0run
Table 45
• Added two rows: IADC1pwd and IADC1run
• Updated values of fADC_1 and tADC1_PU
• Updated tADC1_C row
Updated Table 46
Updated Table 47
Updated Figure 43
Section 6, Ordering information: deleted “Orderable part number summary“ table
5
27 Aug 2010 Removed “Preliminary—Subject to Change Without Notice” marking. This data sheet
contains specifications based on characterization data.
6
08 Jul 2011 Editorial and formatting changes throughout
Replaced instances of “e200z0” with “e200z0h”Device family comparison table:
• changed LINFlex count for 144-pin LQFP—was ‘6’; is ‘8’
• changed LINFlex count for 176-pin LQFP—was ‘8’; is ‘10’
• replaced 105 °C with 125 °C in footnote 2
MPC5607B block diagram: added GPIO and VREG to legend
MPC5607B series block summary: added acronym “JTAGC”; in WKPU function changed
“up to 18 external sources” to “up to 27 external sources”
144 LQFP pin configuration: for pins 37–72, restored the pin labels that existed prior to
27 July 2010
176 LQFP pin configuration: corrected name of pin 4: was EPC[15]; is PC[15]
Added following sections:
• Pad configuration during reset phases
• Pad configuration during standby mode exit
• Voltage supply pins
• Pad types
• System pins
• Functional port pins
• Nexus 2+ pins
Section “NVUSRO register”: edited content to separate configuration into electrical
parameters and digital functionality; updated footnote describing default value of ‘1’ in
field descriptions NVUSRO[PAD3V5V] and NVUSRO[OSCILLATOR_MARGIN]
Added section “NVUSRO[WATCHDOG_EN] field description”
Tables “Absolute maximum ratings” and “Recommended operating conditions (3.3 V)”:
replaced “VSS_HV_ADC0, VSS_HV_ADC1” with “VDD_HV_ADC0, VDD_HV_ADC1”
in VDD_ADC parameter description
“Recommended operating conditions (5.0 V)” table: replaced “VSS_HV_ADC0,
VSS_HV_ADC1” with “VDD_HV_ADC0, VDD_HV_ADC1” in VDD_ADC parameter
description; changed 3.6V to 3.0V in footnote 2
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
109
Revision history
Table 51. Revision history (continued)
Revision
6
(cont’d)
Date
Substantive changes
08 Jul 2011 Section “External ballast resistor recommendations”: replaced “low voltage monitor” with
“low voltage detector (LVD)”
“I/O input DC electrical characteristics” table: updated ILKG characteristics
“MEDIUM configuration output buffer electrical characteristics” table: changed
“IOH = 100 µA” to “IOL = 100 µA” in VOL conditions
I/O weight: updated table (includes replacing instances of bit “SRE” with “SRC”)
“Reset electrical characteristics” table: updated parameter classification for |IWPU|
Updated voltage regulator electrical characteristics
Section “Low voltage detector electrical characteristics”: changed title (was “Voltage
monitor electrical characteristics”); changed “as well as four low voltage detectors” to
“as well as five low voltage detectors”; added event status flag names found in RGM
chapter of device reference manual to POR module and LVD descriptions; replaced
instances of “Low voltage monitor” with “Low voltage detector”; updated values for
VLVDLVBKPL and VLVDLVCORL
Updated section “Power consumption”
Section “Program/erase characteristics”: removed table “FLASH_BIU settings vs.
frequency of operation” and associated introduction
“Program and erase specifications” table: updated symbols
PFCRn settings vs. frequency of operation: replaced “FLASH_BIU” with “PFCRn” in table
title; updated field names and frequencies
“Flash power supply DC electrical characteristics” table: deleted footnote 2
Crystal oscillator and resonator connection scheme: inserted footnote about possibly
requiring a series resistor
Fast external crystal oscillator (4 to 16 MHz) electrical characteristics: updated parameter
classification for VFXOSCOP
Slow external crystal oscillator (32 kHz) electrical characteristics: updated footnote 1
Section “ADC electrical characteristics”: updated symbols for offset error and gain error
Section “Input impedance and ADC accuracy”: changed “VA/VA2” to “VA2/VA” in
Equation 11
ADC input leakage current: updated ILKG characteristics
ADC_0 conversion characteristics table: replaced instances of
“ADCx_conf_sample_input” with “INPSAMP”; replaced instances of
“ADCx_conf_comp” with “INPCMP
ADC_1 characteristic and error definitions: replaced “AVDD” with “VDD_ADC”
ADC_1 conversion characteristics table: replaced instances of
“ADCx_conf_sample_input” with “INPSAMP”; replaced instances of
“ADCx_conf_comp” with “INPCMP”
Updated “On-chip peripherals current consumption” table
MPC5607B Microcontroller Data Sheet, Rev. 8
110
Freescale Semiconductor
Revision history
Table 51. Revision history (continued)
Revision
Date
Substantive changes
7
13 May 2013 In the cover feature list:
added “and ECC” at the end of
“Up to 1.5 MB on-chip code flash memory supported with the flash memory controller”
added “with ECC” at the end of “Up to 96 KB on-chip SRAM”
Table 1 (MPC5607B family comparison), updated SCI (LINFlex) values, 8 channels for
both MPC5605B and MPC5606B 176-pin.
Table 12 (Recommended operating conditions (3.3 V)), updated conditions of TA values
and relative footnote.
Table 13 (Recommended operating conditions (5.0 V)), updated conditions of TA values
and relative footnote.
Table 20 (Output pin transition times), replaced Ttr with ttr
Table 24 (Reset electrical characteristics), replaced Ttr with ttr
Updated Section 4.17.2, “Input impedance and ADC accuracy
Table 26 (Low voltage detector electrical characteristics), changed VLVDHV3L(min) and
VLVDHV3BL(min) from 2.7 V to 2.6 V.
Table 28 (Program and erase specifications), added footnote about tESRT
Table 40 (FMPLL electrical characteristics), deleted footnote relative to maximum value
of fCPU
Table 44 (ADC_0 conversion characteristics (10-bit ADC_0)), changed IADC0run value
from 40 mA to 5 mA.
Table 47 (DSPI characteristics), in the heading row, replaced
DSPI0/DSPI1/DSPI5/DSPI6 with DSPI0/DSPI1/DSPI3/DSPI5
8
18 Apr 2014 Added “K=TSMC Fab” against the Fab and mask indicator in Figure 43 (Commercial
product code structure).
MPC5607B Microcontroller Data Sheet, Rev. 8
Freescale Semiconductor
111
How to Reach Us:
Information in this document is provided solely to enable system and software
Home Page:
freescale.com
implementers to use Freescale products. There are no express or implied copyright
Web Support:
freescale.com/support
information in this document.
licenses granted hereunder to design or fabricate any integrated circuits based on the
Freescale reserves the right to make changes without further notice to any products
herein. Freescale makes no warranty, representation, or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale assume any
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters that may be provided in Freescale data sheets and/or
specifications can and do vary in different applications, and actual performance may
vary over time. All operating parameters, including “typicals,” must be validated for each
customer application by customer’s technical experts. Freescale does not convey any
license under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found at the following
address: freescale.com/SalesTermsandConditions
Freescale, the Freescale logo, and Qorivva are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are
the property of their respective owners. The Power Architecture and Power.org word
marks and the Power and Power.org logos and related marks are trademarks and
service marks licensed by Power.org.
© 2010-2014 Freescale Semiconductor, Inc.
Document Number: MPC5607B
Rev. 8
04/2014