LT3755/LT3755-1/LT3755-2 40VIN, 75VOUT LED Controllers Features Description 3000:1 True Color PWM™ Dimming Wide Input Voltage Range: 4.5V to 40V Output Voltage Up to 75V Constant-Current and Constant-Voltage Regulation 100mV High Side Current Sense Drives LEDs in Boost, Buck Mode, Buck-Boost Mode, SEPIC or Flyback Topology n Adjustable Frequency: 100kHz to 1MHz n Open LED Protection n Programmable Undervoltage Lockout with Hysteresis n Improved Open LED Status Pin (LT3755-2) n Frequency Synchronization (LT3755-1) n PWM Disconnect Switch Driver n CTRL Pin Provides Analog Dimming n Low Shutdown Current: <1µA n Programmable Soft-Start n Thermally Enhanced 16-Lead QFN (3mm × 3mm) and MSOP Packages The LT®3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of supply and output voltages. A ground referenced voltage FB pin serves as the input for several LED protection features, and also makes it possible for the converter to operate as a constant-voltage source. A frequency adjust pin allows the user to program the frequency from 100kHz to 1MHz to optimize efficiency, performance or external component size. n n n n n n The LT3755/LT3755-1/LT3755-2 sense output current at the high side of the LED string. High side current sensing is the most flexible scheme for driving LEDs, allowing boost, buck mode or buck-boost mode configuration. The PWM input provides LED dimming ratios of up to 3000:1, and the CTRL input provides additional analog dimming capability. Applications L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. True Color PWM is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 7199560, 7321203. High Power LED n Battery Chargers n Accurate Current Limited Voltage Regulators n Typical Application 50W White Automotive LED Headlamp Driver Efficiency vs VIN 22µH 4.7µF 1M 185k VIN SHDN/UVLO VREF 332k 40.2k 23.7k 0.1Ω 1A ISN GATE 100k 0.01µF 96 FB ISP LT3755-2 CTRL INTVCC 100 4.7µF 1M EFFICIENCY (%) VIN 8V TO 40V SENSE 28.7k 375kHz OPENLED PWM SS PWMOUT RT VC GND INTVCC 10k 0.015Ω 50W LED STRING 92 88 84 80 4.7µF 0.001µF 0 10 20 VIN (V) 30 40 37551 TA01b 37551 TA01a 37551fd LT3755/LT3755-1/LT3755-2 Absolute Maximum Ratings (Note 1) VIN.............................................................................40V SHDN/UVLO (Note 3).................................................40V ISP, ISN......................................................................75V INTVCC....................................................... VIN + 0.3V, 8V GATE, PWMOUT (Note 4).......................... INTVCC + 0.3V CTRL, PWM, OPENLED..............................................12V VC, VREF, SS, FB...........................................................3V SYNC...........................................................................8V RT.............................................................................1.5V SENSE.......................................................................0.5V Operating Junction Temperature Range (Notes 2, 5) LT3755E/LT3755I................................–40°C to 125°C LT3755H............................................–40°C TO 150°C Storage Temperature Range.................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) MSOP................................................................ 300°C Pin Configuration ISN ISP VC CTRL TOP VIEW 16 15 14 13 VREF 1 TOP VIEW 12 FB PWM 2 11 PWMOUT 17 GND SYNC OR OPENLED 3 PWMOUT FB ISN ISP VC CTRL VREF PWM 10 GATE 5 6 7 8 RT INTVCC VIN 9 SENSE SHDN/UVLO SS 4 1 2 3 4 5 6 7 8 17 GND 16 15 14 13 12 11 10 9 GATE SENSE VIN INTVCC SHDN/UVLO RT SS SYNC OR OPENLED MSE PACKAGE 16-LEAD PLASTIC MSOP TJMAX = 125°C (E, I GRADES), TJMAX = 150°C (H GRADE), θJA = 43°C/W, θJC = 4°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB UD PACKAGE 16-LEAD (3mm s 3mm) PLASTIC QFN TJMAX = 125°C, θJA = 68°C/W, θJC = 4.2°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB order information LEAD FREE FINISH LT3755EUD#PBF TAPE AND REEL LT3755EUD#TRPBF PART MARKING* LDGC PACKAGE DESCRIPTION LT3755IUD#PBF LT3755IUD#TRPBF LDGC 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LT3755EUD-1#PBF LT3755EUD-1#TRPBF LDMS 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LT3755IUD-1#PBF LT3755IUD-1#TRPBF LDMS 16-Lead (3mm × 3mm) Plastic QFN LT3755EUD-2#PBF LT3755EUD-2#TRPBF LFJZ LT3755IUD-2#PBF LT3755IUD-2#TRPBF LFJZ 16-Lead (3mm × 3mm) Plastic QFN TEMPERATURE RANGE –40°C to 125°C –40°C to 125°C –40°C to 125°C 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C 16-Lead (3mm × 3mm) Plastic QFN LT3755EMSE#PBF LT3755EMSE#TRPBF 3755 16-Lead Plastic MSOP –40°C to 125°C LT3755IMSE#PBF LT3755IMSE#TRPBF 3755 16-Lead Plastic MSOP –40°C to 125°C LT3755EMSE-1#PBF LT3755EMSE-1#TRPBF 37551 16-Lead Plastic MSOP –40°C to 125°C LT3755IMSE-1#PBF LT3755IMSE-1#TRPBF 37551 16-Lead Plastic MSOP –40°C to 125°C LT3755EMSE-2#PBF LT3755EMSE-2#TRPBF 37552 16-Lead Plastic MSOP –40°C to 125°C LT3755IMSE-2#PBF LT3755IMSE-2#TRPBF 37552 16-Lead Plastic MSOP –40°C to 125°C LT3755HMSE-2#PBF LT3755HMSE-2#TRPBF 37552 16-Lead Plastic MSOP –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 37551fd LT3755/LT3755-1/LT3755-2 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 24V, SHDN/UVLO = 24V, CTRL = 2V, PWM = 5V, unless otherwise noted. PARAMETER CONDITIONS VIN Minimum Operating Voltage VIN Tied to INTVCC VIN Shutdown IQ SHDN/UVLO = 0V, PWM = 0V SHDN/UVLO = 1.15V, PWM = 0V VIN Operating IQ (Not Switching) PWM = 0V VREF Voltage 100µA ≤ IVREF ≤ 0µA VREF Line Regulation 4.5V ≤ VIN ≤ 40V SENSE Current Limit Threshold MIN l Current Out of Pin SS Pull-Up Current Current Out of Pin 1.965 MAX 98 UNITS 4.5 V 0.1 1 5 µA µA 1.4 1.7 mA 2.00 2.045 0.006 l SENSE Input Bias Current TYP l 108 V %/V 118 40 mV µA 8 10 13 µA 96 100 103 mV –12 –9.5 –7 mV 1.1 V 50 100 nA 75 V 200 mV Error Amplifier ISP/ISN Full-Scale Current Sense Threshold FB = 0V, ISP = 48V ISP/ISN Full-Scale Current Sense Threshold at CTRL = 0V CTRL = 0V, FB = 0V, ISP = 48V CTRL Pin Range for Current Sense Threshold Adjustment CTRL Input Bias Current l 0 Current Out of Pin LED Current Sense Amplifier Input Common Mode Range (VISN) ISP/ISN Short-Circuit Threshold l l ISN = 0V ISP/ISN Short-Circuit Fault Sensing Common Mode Range (VISN) 2.9 115 l 150 0 ISP/ISN Input Bias Current (Combined) PWM = 5V (Active), ISP = ISN = 48V PWM = 0V (Standby), ISP = ISN = 48V 55 0 LED Current Sense Amplifier gm V(ISP – ISN) = 100mV 120 VC Output Impedance 1V < VC < 2V VC Standby Input Bias Current PWM = 0V FB Regulation Voltage (VFB) ISP = ISN 3 V 0.1 µA µA µS 15000 –20 l 1.232 1.220 1.250 1.250 kΩ 20 nA 1.265 1.270 V V FB Amplifier gm FB = VFB, ISP = ISN 480 µS FB Pin Input Bias Current Current Out of Pin 40 100 nA FB Open LED Threshold OPENLED Falling (LT3755 and LT3755-2) VFB – 65mV VFB – 50mV VFB – 40mV V FB Overvoltage Threshold PWMOUT Falling VFB + 50mV VFB + 60mV VFB + 75mV V 4 VC Current Mode Gain – (∆VVC /∆VSENSE) V/V Oscillator Switching Frequency Minimum Off-Time RT = 100k RT = 10k l 90 925 100 1000 170 125 1050 kHz kHz ns 37551fd LT3755/LT3755-1/LT3755-2 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 24V, SHDN/UVLO = 24V, CTRL = 2V, PWM = 5V, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX 7 7.15 7.3 UNITS Linear Regulator INTVCC Regulation Voltage Dropout (VIN – INTVCC) IINTVCC = –10mA, VIN = 7V 350 INTVCC Undervoltage Lockout INTVCC Current Limit INTVCC Current in Shutdown 3.9 4.1 29 SHDN/UVLO = 0V, INTVCC = 7V V mV 4.3 V 34 40 mA 8 12 µA Logic Inputs/Outputs PWM Input High Voltage l PWM Input Low Voltage l PWM Pin Resistance to GND 1.5 45 PWMOUT Output Low (VOL) 0.4 V 50 mV 60 0 PWMOUT Output High (VOH) SHDN/UVLO Threshold Voltage Falling V kΩ INTVCC – 0.05 E-, I-Grades H-Grade l l 1.185 1.175 SHDN/UVLO Rising Hysteresis V 1.220 1.245 1.245 20 SHDN/UVLO Input Low Voltage IVIN Drops Below 1µA SHDN/UVLO Pin Bias Current Low SHDN/UVLO = 1.15V SHDN/UVLO Pin Bias Current High SHDN/UVLO = 1.30V OPENLED Output Low (VOL) IOPENLED = 0.5mA (LT3755 and LT3755-2) SYNC Pin Resistance to GND LT3755-1 Only SYNC Input High LT3755-1 Only SYNC Input Low LT3755-1 Only 1.7 V V mV 0.4 V 2.05 2.5 µA 10 100 nA 200 mV 30 kΩ 1.5 V 0.4 V Gate Driver tr GATE Driver Output Rise Time CL = 3300pF 35 ns tf GATE Driver Output Fall Time CL = 3300pF 35 ns GATE Output Low (VOL) GATE Output High (VOH) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3755E, LT3755E-1 and LT3755E-2 are guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3755I, LT3755I-1 and LT3755I-2 are guaranteed to meet performance specifications over the –40°C to 125°C operating junction temperature range. The LT3755H-2 is guaranteed to meet performance specifications over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. 0.05 V INTVCC – 0.05 V Note 3: For VIN below 6V, the SHDN/UVLO pin must not exceed VIN for proper operation. Note 4: GATE and PWMOUT pins are driven either to GND or INTVCC by internal switches. Do not connect these pins externally to a power supply. Note 5: The LT3755 includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating junction temperature when overtemperature protection is active. Continuous operating above the specified maximum operating junction temperature may impair device reliability. 37551fd LT3755/LT3755-1/LT3755-2 Typical Performance Characteristics 103 100 102 80 60 40 20 0 0 0.5 1 101 100 99 98 97 2 1.5 103 VCTRL = 2V 20 0 VCTRL (V) 40 60 ISP VOLTAGE (V) 100 99 98 97 –50 –25 80 VREF Voltage vs Temperature 1.27 2.03 2.03 1.26 2.02 2.02 1.25 2.01 2.01 VREF (V) 2.04 2.00 1.99 2.00 1.99 1.22 1.98 1.98 1.21 1.97 1.97 1.20 –50 –25 0 1.96 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) SWITCHING FREQUENCY (kHz) 500 10 100 RT (k) 37551 G07 10 30 40 2.4 RT = 26.7k 450 2.2 400 350 300 –50 –25 20 VIN (V) SHDN/UVLO Hysteresis Current vs Temperature ISHDN/UVLO (µA) 10000 100 0 37551 G06 Switching Frequency vs Temperature Switching Frequency vs RT 10 1.96 37551 G05 37551 G04 1000 25 50 75 100 125 150 TEMPERATURE (°C) VREF Voltage vs VIN 2.04 1.23 0 37551 G03 1.28 VREF (V) VFB (V) FB Regulation Voltage vs Temperature SWITCHING FREQUENCY (kHz) 101 37551 G02 37551 G01 1.24 VCTRL = 2V 102 V(ISP – ISN) THRESHOLD (mV) 120 –20 V(ISP – ISN) Threshold vs Temperature V(ISP – ISN) Threshold vs VISP V(ISP – ISN) THRESHOLD (mV) V(ISP – ISN) THRESHOLD (mV) V(ISP – ISN) Threshold vs VCTRL TA = 25°C, unless otherwise noted. 2.0 1.8 0 25 50 75 100 125 150 TEMPERATURE (°C) 37551 G08 1.6 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 37551 G09 37551fd LT3755/LT3755-1/LT3755-2 Typical Performance Characteristics SENSE Current Limit Threshold vs Temperature Quiescent Current vs VIN 110 SENSE THRESHOLD (mV) PWM = 0V VIN CURRENT (mA) 1.5 1.0 0.5 0 0 10 20 VIN (V) 30 1.28 105 100 95 90 –50 –25 40 0 2 30 38 7.3 36 34 0 125 25 50 75 DUTY CYCLE (%) 100 37551 G16 25 50 75 100 125 150 TEMPERATURE (°C) Gate Rise/Fall Time vs Capacitance 100 VCTRL = 2V 100 75 50 25 0 1.2 10% TO 90% 80 TIME (ns) V(ISP – ISN) THRESHOLD (mV) SENSE THRESHOLD (mV) 100 0 37551 G15 V(ISP-ISN) Threshold vs FB Voltage 115 0 7.0 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 37551 G14 SENSE Current Limit Threshold vs Duty Cycle 95 7.2 7.1 32 37551 G13 105 25 50 75 100 125 150 TEMPERATURE (°C) 7.4 30 –50 –25 40 110 0 INTVCC Voltage vs Temperature INTVCC (V) INTVCC CURRENT LIMIT (mA) VINTVCC (V) 4 20 VIN (V) 1.20 37551 G12 40 6 SHDN/UVLO FALLING 1.22 INTVCC Current Limit vs Temperature 8 10 SHDN/UVLO RISING 1.24 37551 G11 INTVCC Voltage vs VIN 0 1.26 1.18 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 37551 G10 0 SHDN/UVLO Threshold vs Temperature SHDN/UVLO VOLTAGE (V) 2.0 TA = 25°C, unless otherwise noted. GATE RISE TIME 60 GATE FALL TIME 40 20 1.22 1.24 1.26 FB VOLTAGE (V) 1.28 37551 G17 0 0 2 4 6 CAPACITANCE (nF) 8 10 37551 G18 37551fd LT3755/LT3755-1/LT3755-2 Typical Performance Characteristics ISP/ISN Input Bias Current vs CTRL Voltage INTVCC Dropout Voltage vs Current, Temperature 0 40 TA = –45°C –0.5 30 LDO DROPOUT (V) INPUT BIAS CURRENT (µA) ISP ISN 20 10 0 TA = 25°C, unless otherwise noted. TA = 25°C TA = 125°C –1.0 TA = 150°C –1.5 –2.0 0 0.5 1 CTRL (V) 1.5 2 37551 G19 Pin Functions –2.5 VIN = 7V 0 5 10 15 20 LDO CURRENT (mA) 25 30 37551 G20 (MSOP/QFN) PWMOUT (Pin 1/Pin 11): Buffered Version of PWM Signal for Driving LED Load Disconnect NMOS or Level Shift. This pin also serves in a protection function for the FB overvoltage condition—will toggle if the FB input is greater than the FB regulation voltage (VFB) plus 60mV (typical). The PWMOUT pin is driven from INTVCC. Use of a FET with gate cut-off voltage higher than 1V is recommended. FB (Pin 2/Pin 12): Voltage Loop Feedback Pin. FB is intended for constant-voltage regulation or for LED protection/open LED detection. The internal transconductance amplifier with output VC will regulate FB to 1.25V (nominal) through the DC/DC converter. If the FB input is regulating the loop, the OPENLED pull-down is asserted. This action may signal an open LED fault. If FB is driven above the FB threshold (by an external power supply spike, for example), the OPENLED pull-down will be de-asserted and the PWMOUT pin will be driven low to protect the LEDs from an overcurrent event. Do not leave the FB pin open. If not used, connect to GND. ISN (Pin 3/Pin 13): Connection Point for the Negative Terminal of the Current Feedback Resistor. If ISN is greater than 2.9V, the LED current can be programmed by ILED = 100mV/RLED when VCTRL > 1.2V or ILED = (VCTRL –100mV)/ (10 • RLED) when VCTRL ≤ 1V. Input bias current is typically 25µA. Below 3V, ISN is an input to the short-circuit protection feature that forces GATE to 0V if ISP exceeds ISN by more than 150mV (typ). ISP (Pin 4/Pin 14): Connection Point for the Positive Terminal of the Current Feedback Resistor. Input bias current is dependent upon CTRL pin voltage as shown in the TPC. ISP is an input to the short‑circuit protection feature when ISN is less than 3V. VC (Pin 5/Pin 15): Transconductance Error Amplifier Output Pin Used to Stabilize the Voltage Loop with an RC Network. This pin is high impedance when PWM is low, a feature that stores the demand current state variable for the next PWM high transition. Connect a capacitor between this pin and GND; a resistor in series with the capacitor is recommended for fast transient response. 37551fd LT3755/LT3755-1/LT3755-2 Pin Functions (MSOP/QFN) CTRL (Pin 6/Pin 16): Current Sense Threshold Adjustment Pin. Regulating threshold V(ISP – ISN) is 1/10th VCTRL plus an offset for 0V < VCTRL < 1V. For VCTRL > 1.2V the current sense threshold is constant at the full-scale value of 100mV. For 1V < VCTRL < 1.2V, the dependence of current sense threshold upon VCTRL transitions from a linear function to a constant value, reaching 98% of full-scale value by VCTRL = 1.1V. Do not leave this pin open. VREF (Pin 7/Pin 1): Voltage Reference Output Pin, Typically 2V. This pin drives a resistor divider for the CTRL pin, either for analog dimming or for temperature limit/compensation of LED load. Can supply up to 100μA. PWM (Pin 8/Pin 2): A signal low turns off switcher, idles oscillator and disconnects VC pin from all internal loads. PWMOUT pin follows PWM pin. PWM has an internal pull-down resistor. If not used, connect to INTVCC. OPENLED (Pin 9/Pin 3, LT3755 and LT3755-2): An opencollector pull-down on OPENLED asserts if the FB input is greater than the FB regulation threshold minus 50mV (typical). To function, the pin requires an external pull-up current less than 1mA. When the PWM input is low and the DC/DC converter is idle, the OPENLED condition is latched to the last valid state when the PWM input was high. When PWM input goes high again, the OPENLED pin will be updated. This pin may be used to report an open LED fault. SYNC (Pin 9/Pin 3, LT3755-1 Only): The SYNC pin is used to synchronize the internal oscillator to an external logic level signal. The RT resistor should be chosen to program an internal switching frequency 20% slower than the SYNC pulse frequency. Gate turn-on occurs a fixed delay after the rising edge of SYNC. For best PWM performance, the PWM rising edge should occur at least 200ns before the SYNC rising edge. Use a 50% duty cycle waveform to drive this pin. This pin replaces OPENLED on LT3755-1 option parts. If not used, tie this pin to GND. SS (Pin 10/Pin 4): Soft-Start Pin. This pin modulates oscillator frequency and compensation pin voltage (VC) clamp. The soft-start interval is set with an external capacitor. The pin has a 10µA (typical) pull-up current source to an internal 2.5V rail. The soft-start pin is reset to GND by an undervoltage condition (detected by SHDN/UVLO pin) or thermal limit. RT (Pin 11/Pin 5): Switching Frequency Adjustment Pin. Set the frequency using a resistor to GND (for resistor values, see the Typical Performance curve or Table 1). Do not leave the RT pin open. SHDN/UVLO (Pin 12/Pin 6): Shutdown and Undervoltage Detect Pin. An accurate 1.22V falling threshold with externally programmable hysteresis detects when power is OK to enable switching. Rising hysteresis is generated by the external resistor divider and an accurate internal 2.1µA pull-down current. Above the threshold (but below 6V), SHDN/UVLO input bias current is sub‑µA. Below the falling threshold, a 2.1µA pull-down current is enabled so the user can define the hysteresis with the external resistor selection. An undervoltage condition resets soft-start. Tie to 0.4V, or less, to disable the device and reduce VIN quiescent current below 1µA. INTVCC (Pin 13/Pin 7): Regulated Supply for Internal Loads, GATE Driver and PWMOUT Driver. Supplied from VIN and regulates to 7.15V (typical). INTVCC must be bypassed with a 4.7µF capacitor placed close to the pin. Connect INTVCC directly to VIN if VIN is always less than or equal to 8V. VIN (Pin 14/Pin 8): Input Supply Pin. Must be locally bypassed with a 0.22µF (or larger) capacitor placed close to the IC. SENSE (Pin 15/Pin 9): The current sense input for the control loop. Kelvin connect this pin to the positive terminal of the switch current sense resistor, RSENSE, in the source of the NFET. The negative terminal of the current sense resistor should be Kelvin connected to the GND plane of the IC. GATE (Pin 16/Pin 10): N-channel FET Gate Driver Output. Switches between INTVCC and GND. Driven to GND during shutdown, fault or idle states. Exposed Pad (Pin 17/Pin 17): Ground. This pin also serves as current sense input for control loop, sensing negative terminal of current sense resistor. Solder the Exposed Pad directly to ground plane. 37551fd LT3755/LT3755-1/LT3755-2 Block Diagram SHDN/UVLO 1.22V – + A6 VC FB 1.3V 2.1µA A5 + gm – 1.25V SHORT-CIRCUIT DETECT + – + A10 – 150mV gm EAMP ISN + A1 – 5k ISP CTRL BUFFER CTRL 1.1V + + A3 – OVFB COMPARATOR 2V 170k R 7.15V INTVCC GATE Q DRIVER S PWM COMPARATOR 10µA AT A1+ = A1– ISENSE + – SENSE A4 FAULT LOGIC GND RAMP GENERATOR VC SSCLAMP – +A7 – LDO +A8 1.25V + A2 – 50k VREF VIN SCILMB Q2 140µA PWM 10µA AT FB = 1.25V 10µA SCILMB PWMOUT – + SHDN 100KHz TO 1MHz OSCILLATOR 10µA 1.25V TLIM 165°C SS + + – 1.2V FB FREQ PROG RT – + OPENLED OPTION FOR LT3755 AND LT3755-2 SYNC OPTION FOR LT3755-1 37551 BD 37551fd LT3755/LT3755-1/LT3755-2 Operation The LT3755 is a constant-frequency, current mode controller with a low side NMOS gate driver. The GATE pin and PWMOUT pin drivers and other chip loads are powered from INTVCC, which is an internally regulated supply. In the discussion that follows it will be helpful to refer to the Block Diagram of the IC. In normal operation with the PWM pin low, the GATE and PWMOUT pins are driven to GND, the VC pin is high impedance to store the previous switching state on the external compensation capacitor, and the ISP and ISN pin bias currents are reduced to leakage levels. When the PWM pin transitions high, the PWMOUT pin transitions high after a short delay. At the same time, the internal oscillator wakes up and generates a pulse to set the PWM latch, turning on the external power MOSFET switch (GATE goes high). A voltage input proportional to the switch current, sensed by an external current sense resistor between the SENSE and GND input pins, is added to a stabilizing slope compensation ramp and the resulting “switch current sense” signal is fed into the positive terminal of the PWM comparator. The current in the external inductor increases steadily during the time the switch is on. When the switch current sense voltage exceeds the output of the error amplifier, labeled “VC”, the latch is reset and the switch is turned off. During the switch-off phase, the inductor current decreases. At the completion of each oscillator cycle, internal signals such as slope compensation return to their starting points and a new cycle begins with the set pulse from the oscillator. Through this repetitive action, the PWM control algorithm establishes a switch duty cycle to regulate a current or voltage in the load. The VC signal is integrated over many switching cycles and is an amplified version of the difference between the LED current sense voltage, measured between ISP and ISN, and the target difference voltage set by the CTRL pin. In this manner, the error amplifier sets the correct peak switch current level to keep the LED current in regulation. If the error amplifier output increases, more current is demanded in the switch; if it decreases, less current is demanded. The switch current is monitored during the on-phase and the voltage across the SENSE pin is not allowed to exceed the current limit threshold of 108mV (typical). If the SENSE pin exceeds the current limit threshold, the SR latch is reset regardless of the output state of the PWM comparator. Likewise, at an ISP/ISN common mode voltage less than 3V, the dif- ference between ISP and ISN is monitored to determine if the output is in a short-circuit condition. If the difference between ISP and ISN is greater than 150mV (typical), the SR latch will be reset regardless of the PWM comparator. These functions are intended to protect the power switch as well as various external components in the power path of the DC/DC converter. In voltage feedback mode, the operation is similar to that described above, except the voltage at the VC pin is set by the amplified difference of the internal reference of 1.25V (nominal) and the FB pin. If FB is lower than the reference voltage, the switch current will increase; if FB is higher than the reference voltage, the switch demand current will decrease. The LED current sense feedback interacts with the FB voltage feedback so that FB will not exceed the internal reference and the voltage between ISP and ISN will not exceed the threshold set by the CTRL pin. For accurate current or voltage regulation, it is necessary to be sure that under normal operating conditions the appropriate loop is dominant. To deactivate the voltage loop entirely, FB can be connected to GND. To deactivate the LED current loop entirely, the ISP and ISN should be tied together and the CTRL input tied to VREF . Two LED specific functions featured on the LT3755 are controlled by the voltage feedback pin. First, when the FB pin exceeds a voltage 50mV lower (–4%) than the FB regulation voltage, the pull-down driver on the OPENLED pin is activated (LT3755 and LT3755-2 only). This function provides a status indicator that the load may be disconnected and the constant-voltage feedback loop is taking control of the switching regulator. When the FB pin exceeds the FB regulation voltage by 60mV (5% typical), the PWMOUT pin is driven low, ignoring the state of the PWM input. In the case where the PWMOUT pin drives a disconnect NFET, this action isolates the LED load from GND preventing excessive current from damaging the LEDs. If the FB input exceeds both the open LED and the overvoltage thresholds, then an externally driven overvoltage event has caused the FB pin to be too high and the OPENLED pull-down will be de-asserted. The LT3755-2 will re-assert the OPENLED signal when FB falls below the overvoltage threshold and remains above the OPENLED threshold. The LT3755 is prevented from re-asserting OPENLED until FB drops below both thresholds. 37551fd 10 LT3755/LT3755-1/LT3755-2 Applications Information INTVCC Regulator Bypassing and Operation The INTVCC pin requires a capacitor for stable operation and to store the charge for the large GATE switching currents. Choose a 10V rated low ESR, X7R or X5R ceramic capacitor for best performance. A 4.7µF capacitor will be adequate for many applications. Place the capacitor close to the IC to minimize the trace length to the INTVCC pin and also to the IC ground. The following equations should be used to determine the values of the resistors: VIN,RISING VIN An internal current limit on the INTVCC output protects the LT3755 from excessive on-chip power dissipation. The minimum value of this current should be considered when choosing the switching NMOS and the operating frequency. LT3755 Careful choice of a lower QG FET will allow higher switching frequencies, leading to smaller magnetics. The INTVCC pin has its own undervoltage disable (UVLO) set to 4.1V (typical) to protect the external FETs from excessive power dissipation caused by not being fully enhanced. If the INTVCC pin drops below the UVLO threshold, the GATE and PWMOUT pins will be forced to 0V and the soft-start pin will be reset. If the input voltage, VIN, will not exceed 8V, then the INTVCC pin could be connected to the input supply. Be aware that a small current (less than 12μA) will load the INTVCC in shutdown. This action allows the LT3755 to operate from VIN as low as 4.5V. If VIN is normally above, but occasionally drops below the INTVCC regulation voltage, then the minimum operating VIN will be close to 6V . This value is determined by the dropout voltage of the linear regulator and the INTVCC undervoltage lockout threshold mentioned above. Programming the Turn-On and Turn-Off Thresholds with the SHDN/UVLO Pin The falling UVLO value can be accurately set by the resistor divider. A small 2.1µA pull-down current is active when SHDN/UVLO is below the threshold. The purpose of this current is to allow the user to program the rising hysteresis. R1 SHDN/UVLO R2 37551 F01 Figure 1. Resistor Connection to Set VIN Undervoltage Shutdown Threshold IINTVCC can be calculated from the following equation: IINTVCC = QG • fOSC R1+R2 R2 = 2.1µA •R1 + VIN,FALLING VIN,FALLING = 1.22 • LED Current Programming The LED current is programmed by placing an appropriate value current sense resistor, RLED, in series with the LED string. The voltage drop across RLED is (Kelvin) sensed by the ISP and ISN pins. Typically, sensing of the current should be done at the top of the LED string. If this option is not available, then the current may be sensed at the bottom of the string, but take caution that the minimum ISN value does not fall below 3V, which is the lower limit of the LED current regulation function. The CTRL pin should be tied to a voltage higher than 1.2V to get the full-scale 100mV (typical) threshold across the sense resistor. The CTRL pin can also be used to dim the LED current to zero, although relative accuracy decreases with the decreasing voltage sense threshold. When the CTRL pin voltage is less than 1V, the LED current is: ILED = VCTRL − 100mV RLED • 10 When the CTRL pin voltage is between 1V and 1.2V the LED current varies with CTRL, but departs from the equation above by an increasing amount as CTRL voltage increases. Ultimately, above CTRL = 1.2V the LED current no longer varies with CTRL. At CTRL = 1.1V, the actual value of ILED is ~98% of the equation’s estimate. 37551fd 11 LT3755/LT3755-1/LT3755-2 Applications Information When VCTRL is higher than 1.2V, the LED current is regulated to: ILED = 100mV RLED The LED current programming feature can increase total dimming range by a factor of 10. The CTRL pin should not be left open (tie to VREF if not used). The CTRL pin can also be used in conjunction with a thermistor to provide overtemperature protection for the LED load, or with a resistor divider to VIN to reduce output power and switching current when VIN is low. The presence of a time varying differential voltage signal (ripple) across ISP and ISN at the switching frequency is expected. The amplitude of this signal is increased by high LED load current, low switching frequency and/or a smaller value output filter capacitor. Some level of ripple signal is acceptable: the compensation capacitor on the VC pin filters the signal so the average difference between ISP and ISN is regulated to the user-programmed value. Ripple voltage amplitude (peak-to-peak) in excess of 20mV should not cause misoperation, but may lead to noticeable offset between the average value and the user-programmed value. Programming Output Voltage (Constant Voltage Regulation) or Open LED/Overvoltage Threshold For a boost application, the output voltage can be set by selecting the values of R3 and R4 (see Figure 2) according to the following equation: VOUT = 1.25 • R3 + R4 R4 For a boost type LED driver, set the resistor from the output to the FB pin such that the expected VFB during normal VOUT R3 LT3755 FB R4 37551 F02 Figure 2. Feedback Resistor Connection for Boost or SEPIC LED Driver operation will not exceed 1.1V. For an LED driver of buck or a buck-boost configuration, the output voltage is typically level-shifted to a signal with respect to GND as illustrated in Figure 3. The output can be expressed as: VOUT = VBE + 1.25 • R3 R4 R3 + RSEN(EXT) VOUT – LT3755 100k LED ARRAY COUT 37551 F03 FB R4 Figure 3. Feedback Resistor Connection for Buck Mode or Buck-Boost Mode LED Driver ISP/ISN Short-Circuit Protection Feature (for SEPIC) The ISP and ISN pins have a protection feature independent of the LED current sense feature that operates at ISN below 3V. The purpose of this feature is to provide continuous current sensing when ISN is below the LED current sense common mode range (during start-up or an output short-circuit fault) to prevent the development of excessive switching currents that could damage the power components in a SEPIC converter. The action threshold (150mV, typ) is above the default LED current sense threshold, so that no interference will occur over the ISN voltage range where these two functions overlap. This feature acts in the same manner as SENSE current limit — it prevents GATE from going high (switch turn-on) until the ISP/ISN difference falls below the threshold. If the load has appreciable series inductance, use of a Schottky clamp from GND to ISN is recommended for the SEPIC to prevent excessive current flowing from the ISN pin in a fault. Dimming Control There are two methods to control the current source for dimming using the LT3755. One method uses the CTRL pin to adjust the current regulated in the LEDs. A second method uses the PWM pin to modulate the current source between 37551fd 12 LT3755/LT3755-1/LT3755-2 Applications Information Programming the Switching Frequency The RT frequency adjust pin allows the user to program the switching frequency from 100kHz to 1MHz to optimize efficiency/performance or external component size. Higher frequency operation yields smaller component size but increases switching losses and gate driving current, and may not allow sufficiently high or low duty cycle operation. Lower frequency operation gives better performance at the cost of larger external component size. For an appropriate RT resistor value see Table 1. An external resistor from the RT pin to GND is required—do not leave this pin open. Table 1. Switching Frequency vs RT Value fOSC (kHz) RT (kΩ) 1000 10.0 900 11.8 800 13.0 700 15.4 600 17.8 500 21.0 400 26.7 300 35.7 200 53.6 100 100 Duty Cycle Considerations Switching duty cycle is a key variable defining converter operation, therefore, its limits must be considered when programming the switching frequency for a particular application. The fixed minimum on-time and minimum off-time (see Figure 4) and the switching frequency define the minimum and maximum duty cycle of the switch, respectively. The following equations express the minimum/maximum duty cycle: Min Duty Cycle = (minimum on-time) • switching frequency Max Duty Cycle = 1 – (minimum off-time) • switching frequency When calculating the operating limits, the typical values for on/off-time in the data sheet should be increased by at least 60ns to allow margin for PWM control latitude, GATE rise/fall times and SW node rise/fall times. 300 CGATE = 3300pF 250 MINIMUM ON-TIME 200 TIME (ns) zero and full current to achieve a precisely programmed average current. To make PWM dimming more accurate, the switch demand current is stored on the VC node during the quiescent phase when PWM is low. This feature minimizes recovery time when the PWM signal goes high. To further improve the recovery time, a disconnect switch may be used in the LED current path to prevent the ISP node from discharging during the PWM signal low phase. The minimum PWM on or off time is affected by choice of operating frequency and external component selection. The data sheet application titled “Buck Mode 500mA LED Driver for 20kHz PWM Dimming” demonstrates regulated current pulses as short as 1µs are achievable. The best overall combination of PWM and analog dimming capability is available if the minimum PWM pulse is at least six switching cycles. 150 MINIMUM OFF-TIME 100 50 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 37551 F04 Figure 4. Typical Minimum On and Off Pulse Width vs Temperature Thermal Considerations The LT3755 is rated to a maximum input voltage of 40V. Careful attention must be paid to the internal power dissipation of the IC at higher input voltages to ensure that a junction temperature of 125°C (150°C for H-Grade) is not exceeded. This junction limit is especially important 37551fd 13 LT3755/LT3755-1/LT3755-2 Applications Information when operating at high ambient temperatures. The majority of the power dissipation in the IC comes from the supply current needed to drive the gate capacitance of the external power MOSFET. This gate drive current can be calculated as: IGATE = fSW • QG A low QG power MOSFET should always be used when operating at high input voltages, and the switching frequency should also be chosen carefully to ensure that the IC does not exceed a safe junction temperature. The internal junction temperature of the IC can be estimated by: TJ = TA + [VIN (IQ + fSW • QG) • θJA] where TA is the ambient temperature, IQ is the quiescent current of the part (maximum 1.7mA) and θJA is the package thermal impedance (68°C/W for the 3mm × 3mm QFN package). For example, an application with TA(MAX) = 85°C, VIN(MAX) = 40V, fSW = 400kHz, and having a FET with QG = 20nC, the maximum IC junction temperature will be approximately: TJ= 85°C + [40V (1.7mA + 400kHz • 20nC) • 68°C/W] = 111°C The Exposed Pad on the bottom of the package must be soldered to a ground plane. This ground should then be connected to an internal copper ground plane with thermal vias placed directly under the package to spread out the heat dissipated by the IC. If LT3755 junction temperature reaches 165°C, the GATE and PWMOUT pins will be driven to GND and the softstart (SS) pin will be discharged to GND. Switching will be enabled after device temperature is reduced 10°C. This function is intended to protect the device during momentary thermal overload conditions. Frequency Synchronization (LT3755-1 Only) The LT3755-1 switching frequency can be synchronized to an external clock using the SYNC pin. For proper operation, the RT resistor should be chosen for a switching frequency 20% lower than the external clock frequency. The SYNC pin is disabled during the soft-start period. Observation of the following guidelines about the SYNC waveform will ensure proper operation of this feature. 14 Driving SYNC with a 50% duty cycle waveform is always a good choice, otherwise, maintain the duty cycle between 20% and 60%. When using both PWM and SYNC features, the PWM signal rising edge should occur at least 200ns before the SYNC rising edge (VIH) for optimal PWM performance. If the SYNC pin is not used, it should be connected to GND. Open LED Detection (LT3755 and LT3755-2) The LT3755 and LT3755-2 provide an open-drain status pin, OPENLED, that pulls low when the FB pin is within ~50mV of its 1.25V regulated voltage. If the open LED clamp voltage is programmed correctly using the FB pin, then the FB pin should never exceed 1.1V when LEDs are connected, therefore, the only way for the FB pin to be within 50mV of the regulation voltage is for an open LED event to have occurred. The key difference between the LT3755 and LT3755-2 is the behavior of the OPENLED pin when the FB pin crosses and re-crosses the FB overvoltage threshold (1.31V typ). The LT3755-2 asserts/de-asserts OPENLED freely when crossing the 1.31V threshold. The LT3755, by comparison, de-asserts OPENLED when FB exceeds 1.31V and is prevented from re-asserting OPENLED until the FB pin falls below the 1.2V (typ) open LED threshold and clears the fault. The LT3755-2 has the more general purpose behavior and is recommended for applications using OPENLED. Input Capacitor Selection The input capacitor supplies the transient input current for the power inductor of the converter and must be placed and sized according to the transient current requirements. The switching frequency, output current and tolerable input voltage ripple are key inputs to estimating the capacitor value. An X7R type ceramic capacitor is usually the best choice since it has the least variation with temperature and DC bias. Typically, boost and SEPIC converters require a lower value capacitor than a buck mode converter. Assuming that a 100mV input voltage ripple is acceptable, the required capacitor value for a boost converter can be estimated as follows: CIN (µF) = ILED (A) • µF VOUT • t SW (µs) • A • µs VIN 37551fd LT3755/LT3755-1/LT3755-2 Applications Information Therefore, a 10µF capacitor is an appropriate selection for a 400kHz boost regulator with 12V input, 48V output and 1A load. With the same VIN voltage ripple of 100mV, the input capacitor for a buck converter can be estimated as follows: µF CIN (µF) = ILED (A) • t SW (µs) • 4.7 • A • µs A 10µF input capacitor is an appropriate selection for a 400kHz buck mode converter with a 1A load. In the buck mode configuration, the input capacitor has large pulsed currents due to the current returned through the Schottky diode when the switch is off. In this buck converter case it is important to place the capacitor as close as possible to the Schottky diode and to the GND return of the switch (i.e., the sense resistor). It is also important to consider the ripple current rating of the capacitor. For best reliability, this capacitor should have low ESR and ESL and have an adequate ripple current rating. The RMS input current for a buck mode LED driver is: IIN(RMS) = ILED • (1– D) • D where D is the switch duty cycle. Table 2. Recommended Ceramic Capacitor Manufacturers MANUFACTURER WEB TDK www.tdk.com Kemet www.kemet.com Murata www.murata.com Taiyo Yuden www.t-yuden.com Output Capacitor Selection The selection of the output capacitor depends on the load and converter configuration, i.e., step-up or step-down and the operating frequency. For LED applications, the equivalent resistance of the LED is typically low and the output filter capacitor should be sized to attenuate the current ripple. Use of X7R type ceramic capacitors is recommended. To achieve the same LED ripple current, the required filter capacitor is larger in the boost and buck-boost mode applications than that in the buck mode applications. Lower operating frequencies will require proportionately higher capacitor values. Soft-Start Capacitor Selection For many applications, it is important to minimize the inrush current at start-up. The built-in soft-start circuit significantly reduces the start-up current spike and output voltage overshoot. The soft-start interval is set by the softstart capacitor selection according to the equation: TSS = CSS • 2V 10µA A typical value for the soft-start capacitor is 0.01µF. The soft-start pin reduces the oscillator frequency and the maximum current in the switch. The soft-start capacitor is discharged when SHDN/UVLO falls below its threshold, during an overtemperature event or during an INTVCC undervoltage event. During start-up with SHDN/UVLO, charging of the soft-start capacitor is enabled after the first PWM high period. Power MOSFET Selection For applications operating at high input or output voltages, the power NMOS FET switch is typically chosen for drain voltage VDS rating and low gate charge QG. Consideration of switch on-resistance, RDS(ON), is usually secondary because switching losses dominate power loss. The INTVCC regulator on the LT3755 has a fixed current limit to protect the IC from excessive power dissipation at high VIN, so the FET should be chosen so that the product of QG at 7V and switching frequency does not exceed the INTVCC current limit. For driving LEDs be careful to choose a switch with a VDS rating that exceeds the threshold set by the FB pin in case of an open-load fault. Several MOSFET vendors are listed in Table 3. The MOSFETs used in the application circuits in this data sheet have been found to work well with the LT3755. Consult factory applications for other recommended MOSFETs. Table 3. MOSFET Manufacturers VENDOR WEB Vishay Siliconix www.vishay.com Fairchild www.fairchildsemi.com International Rectifier www.irf.com 37551fd 15 LT3755/LT3755-1/LT3755-2 Applications Information Schottky Rectifier Selection The power Schottky diode conducts current during the interval when the switch is turned off. Select a diode rated for the maximum SW voltage. If using the PWM feature for dimming, it is important to consider diode leakage, which increases with the temperature, from the output during the PWM low interval. Therefore, choose the Schottky diode with sufficiently low leakage current. Table 4 has some recommended component vendors. Table 4. Schottky Rectifier Manufacturers VENDOR WEB On Semiconductor www.onsemi.com Diodes, Inc. www.diodes.com Central Semiconductor www.centralsemi.com Sense Resistor Selection The resistor, RSENSE, between the source of the external NMOS FET and GND should be selected to provide adequate switch current to drive the application without exceeding the 108mV (typical) current limit threshold on the SENSE pin of LT3755. For buck mode applications, select a resistor that gives a switch current at least 30% greater than the required LED current. For buck mode, select a resistor according to: RSENSE,BUCK ≤ 0.07V ILED VIN • 0.07V ( VIN + VLED )ILED For boost, select a resistor according to: RSENSE,BOOST The placement of RSENSE should be close to the source of the NMOS FET and GND of the LT3755. The SENSE input to LT3755 should be a Kelvin connection to the positive terminal of RSENSE. Inductor Selection The inductor used with the LT3755 should have a saturation current rating appropriate to the maximum switch current selected with the RSENSE resistor. Choose an inductor value based on operating frequency, input and output voltage to provide a current mode ramp on SENSE during the switch on-time of approximately 20mV magnitude. The following equations are useful to estimate the inductor value for continuous conduction mode operation: For buck-boost, select a resistor according to: RSENSE,BUCK-BOOST ≤ (DCM) switching. It is always prudent to verify the peak inductor current in the application to ensure the sense resistor selection provides margin to the SENSE current limit threshold. V • 0.07V ≤ IN VLED • ILED These equations provide an estimate of the sense resistor value based on reasonable assumptions about inductor current ripple during steady state switching. Lower values of sense resistor may be required in applications where inductor ripple current is higher. Examples include applications with current limited operation at high duty cycle, and those with discontinuous conduction mode LBUCK = RSENSE • VLED ( VIN – VLED ) VIN • 0.02V • fOSC LBUCK-BOOST = LBOOST = RSENSE • VLED • VIN ( VLED + VIN ) • 0.02V • fOSC RSENSE • VIN ( VLED – VIN ) VLED • 0.02V • fOSC Table 5 provides some recommended inductor vendors. Table 5. Inductor Manufacturers VENDOR WEB Sumida www.sumida.com Würth Elektronik www.we-online.com Coiltronics www.cooperet.com Vishay www.vishay.com Coilcraft www.coilcraft.com Loop Compensation The LT3755 uses an internal transconductance error amplifier whose VC output compensates the control loop. The external inductor, output capacitor and the compensation resistor and capacitor determine the loop stability. 37551fd 16 LT3755/LT3755-1/LT3755-2 Applications Information The inductor and output capacitor are chosen based on performance, size and cost. The compensation resistor and capacitor at VC are selected to optimize control loop response and stability. For typical LED applications, a 2.2nF compensation capacitor at VC is adequate, and a series resistor should always be used to increase the slew rate on the VC pin to maintain tighter regulation of LED current during fast transients on the input supply to the converter. Board Layout The high speed operation of the LT3755 demands careful attention to board layout and component placement. The exposed pad of the package is the only GND terminal of the IC and is also important for thermal management of the IC. It is crucial to achieve a good electrical and thermal contact between the exposed pad and the ground plane of the board. To reduce electromagnetic interference (EMI), it is important to minimize the area of the high dV/dt switching node between the inductor, switch drain and anode of the Schottky rectifier. Use a ground plane under the switching node to eliminate interplane coupling to sensitive signals. The lengths of the high dI/dt traces: 1) from the switch node through the switch and sense resistor to GND, and 2) from the switch node through the Schottky rectifier and filter capacitor to GND should be minimized. The ground points of these two switching current traces should come to a common point then connect to the ground plane under the LT3755. Likewise, the ground terminal of the bypass capacitor for the INTVCC regulator should be placed near the GND of the switching path. Typically this requirement will result in the external switch being closest to the IC, along with the INTVCC bypass capacitor. The ground for the compensation network and other DC control signals should be star connected to the underside of the IC. Do not extensively route high impedance signals such as FB and VC, as they may pick up switching noise. In particular, avoid routing FB and PWMOUT in parallel for more than a few millimeters on the board. Minimize resistance in series with the SENSE input to avoid changes (most likely reduction) to the switch current limit threshold. 20W SEPIC LED Driver C1 4.7µF 50V 1M VIN SHDN/UVLO FB 100k 95 ISP 0.1Ω 1A ISN OPENLED GATE PWM SENSE SS RT PWMOUT VC GND INTVCC 28.7k 375kHz 0.001µF L1: WÜRTH ELEKTRONIK 744870220 M1: VISHAY SILICONIX SI7454DP D1: DIODES INC. - PDS5100 M2: VISHAY SILICONIX SI2318DS 30k VOUT = 18V ILED = 1A L1B LT3755-2 0.01µF 100 25k CTRL INTVCC Efficiency vs VIN C3 4.7µF 50V 511k VREF 187k D1 5A 100V EFFICIENCY (%) VIN 8V TO 40V C4 2.2µF 50V L1A 22µH C2 4.7µF 10V M1 20W LED STRING 0.015Ω 90 85 80 M2 0 10 20 VIN (V) 30 40 37551 TA04b 37551 TA04a 37551fd 17 LT3755/LT3755-1/LT3755-2 CTRL VREF OPENLED PWM Applications Information VIAS TO GROUND PLANE CSS RT R2 4 3 2 1 5 16 CC RC R1 6 15 CVCC 7 14 8 13 x VOUT VIA 9 10 11 12 L1 R3 x R4 5 4 1 6 3 M2 M1 7 2 8 1 3 LED– 2 RSENSE COUT COUT D1 CIN RLED VIN GND COMPONENT DESIGNATIONS REFER TO “50W WHITE LED HEADLAMP DRIVER” SCHEMATIC LED+ 37551 F05 Figure 5. Boost Converter Suggested Layout 37551fd 18 LT3755/LT3755-1/LT3755-2 Typical Applications 50W White LED Headlamp Driver VIN 8V TO 40V L1 22µH CIN 4.7µF R1 1M D1 SHDN/UVLO R2 187k 16.9k FB VREF 100k CSS 0.01µF RT 28.7k 375kHz RLED 0.1Ω LT3755-2 1A ISN 100k NTC RT1 INTVCC R4 23.7k ISP CTRL COUT 4.7µF R3 1M VIN M1 GATE SENSE OPENLED PWM SS RT PWMOUT VC GND INTVCC RC 10k CC 0.001µF L1: COILTRONICS DR127-220 M1: VISHAY SILICONIX SI7850DP D1: DIODES INC. PDS5100 M2: VISHAY SILICONIX SI2308DS RT1: MURATA NCP18WM1045 RSENSE 0.015Ω 50W LED STRING CVCC 4.7µF M2 SEE SUGGESTED LAYOUT, FIGURE 5 37551 TA02a Waveforms for 50W LED Driver with PWM Disconnect NFET PWM VIN = 12V 0V TO 5V VOUT = 50V 10V/DIV IL1 2A/DIV ILED 500mA/DIV 50µs/DIV 37551 TA02b V(ISP-ISN) Threshold vs Temperature for NTC Resistor Divider Efficiency vs Load 100 120 VIN = 12V V(ISP-ISN) THRESHOLD (mV) EFFICIENCY (%) 96 92 88 84 80 0.0 0.2 0.4 0.6 LOAD (A) 0.8 1.0 37551 TA02c 100 80 60 40 20 0 25 45 65 85 TEMPERATURE (°C) 105 125 37551 TA02d 37551fd 19 LT3755/LT3755-1/LT3755-2 Typical Applications Buck Mode 1.4A LED Driver VIN 15V TO 40V C1 1µF 1M ISP VIN 110k SHDN/UVLO 107k 0.068Ω CTRL 200k Q1 1.5k INTVCC 20k M3 LT3755-2 M2 PWMOUT PWM 100k 1.4A ISN FB VREF C3 4.7µF 200k 3 LUXEON K2 - WHITE 1k OPENLED L1 33µH SS D1 VIN 0.1µF 28.7k 375kHz VC GND INTVCC 47k 0.001µF C4 4.7µF M1 GATE RT SENSE 0.033Ω C2 4.7µF 37551 TA03a L1: COILTRONICS DR125-330 M1: VISHAY SILICONIX SI7850DP D1: ON SEMICONDUCTOR MBRS360 M2: ZETEX ZXMN4A06G M3: ZETEX ZXM62P03E6 Q1: ZETEX FMMT558 1000:1 PWM Dimming at 120Hz with Buck Mode Efficiency vs VIN 100 VIN = 24V VLED = 10V PWM 0V TO 5V EFFICIENCY (%) 96 ILED 1A/DIV IL1 1A/DIV 2µs/DIV 37551 TA03b 92 88 84 80 15 20 25 30 35 40 VIN (V) 37551 TA03c 37551fd 20 LT3755/LT3755-1/LT3755-2 Typical Applications Buck Mode 500mA LED Driver for 20kHz PWM Dimming VIN 22V TO 36V 1M ISP VIN SHDN/UVLO 68.1k 0.2Ω ISN VREF CTRL 16V 0.22µF M2 PWMOUT 6V 4.7µF 2s 25V 1M LT3755-2 PWM INTVCC 4.7µF L1 3.3µH 2200pF SENSE VC GND 22k 0.1µF 470pF FB D1 M1 GATE OPENLED SS 500mA RT 0.033Ω 13k 800kHz 2.2µF 2s 50V 37551 TA03a L1: TOKO 962BS_3R3M M1: VISHAY SILICONIX SI7850DP M2: VISHAY SILICONIX SI2306DS D1: DIODES, INC SBM540 Minimum PWM Pulse Switching Waveform Efficiency vs VIN 100 GATE VLED = 16V ILED = 0.5A 96 EFFICIENCY (%) INDUCTOR CURRENT 1A/DIV PWM ILED 500mA/DIV 92 88 84 500ns/DIV 37551 TA06b 80 15 20 25 30 VIN (V) 35 40 37551 TA06c 37551fd 21 LT3755/LT3755-1/LT3755-2 Typical Applications 21W Buck-Boost Mode with 250:1 PWM Dimming and Open LED Protection L1 15µH VIN 8V TO 36V 0.1Ω D1 50V 2.2µF 2s M2 100V 2.2µF 2s M1 392k 21.5V 1A 1.5k 0.02Ω VIN Q1 100k 499k GATE SENSE VIN FB SHDN/UVLO 549k 93.1k VREF LT3755-2 PWMOUT CTRL 75.0k 20.0k 4.7µF Q2 PWM PWM 1k INTVCC ISP 100k ISN OPENLED SS VC 0.01µF GND 4.7k 37551 TA07a RT M1: VISHAY SILICONIX SI7850DP M2: VISHAY SILICONIX SI2319DS Q1: ZETEX FMMT558 Q2: MMBTA42 D1: DIODES INC. PDS560 L1: SUMIDA CDRH127/LD-150 28.7k 375kHz 4700pF Buck-Boost Mode Efficiency vs Input Voltage Buck-Boost Mode LED Current vs Low Input Voltage 100 1.10 1.05 LED CURRENT (A) EFFICIENCY (%) 95 90 1 0.95 0.9 85 0.85 80 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 37551 TA07b 0.8 8 9 10 11 12 13 14 INPUT VOLTAGE (V) 15 16 37551 TA07c 37551fd 22 LT3755/LT3755-1/LT3755-2 Package Description MSE Package MSE Package 16-Lead Plastic MSOP, Exposed Die Pad 16-Lead , Exposed (Reference LTCPlastic DWG #MSOP 05-08-1667 RevDie A) Pad (Reference LTC DWG # 05-08-1667 Rev A) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 p 0.102 (.112 p .004) 5.23 (.206) MIN 2.845 p 0.102 (.112 p .004) 0.889 p 0.127 (.035 p .005) 8 1 1.651 p 0.102 (.065 p .004) 1.651 p 0.102 3.20 – 3.45 (.065 p .004) (.126 – .136) 0.305 p 0.038 (.0120 p .0015) TYP 16 0.50 (.0197) BSC 4.039 p 0.102 (.159 p .004) (NOTE 3) RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 0.12 REF DETAIL “B” CORNER TAIL IS PART OF DETAIL “B” THE LEADFRAME FEATURE. FOR REFERENCE ONLY 9 NO MEASUREMENT PURPOSE 0.280 p 0.076 (.011 p .003) REF 16151413121110 9 DETAIL “A” 0o – 6o TYP 3.00 p 0.102 (.118 p .004) (NOTE 4) 4.90 p 0.152 (.193 p .006) GAUGE PLANE 0.53 p 0.152 (.021 p .006) DETAIL “A” 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 1234567 8 0.50 (.0197) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 p 0.0508 (.004 p .002) MSOP (MSE16) 0608 REV A 37551fd 23 LT3755/LT3755-1/LT3755-2 Package Description UD Package 16-Lead Plastic QFN (3mm × 3mm) (Reference LTC DWG # 05-08-1691) 0.70 ±0.05 3.50 ± 0.05 1.45 ± 0.05 2.10 ± 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 ± 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD PIN 1 NOTCH R = 0.20 TYP OR 0.25 × 45° CHAMFER R = 0.115 TYP 0.75 ± 0.05 15 PIN 1 TOP MARK (NOTE 6) 16 0.40 ± 0.10 1 1.45 ± 0.10 (4-SIDES) 2 (UD16) QFN 0904 0.200 REF 0.00 – 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WEED-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 ± 0.05 0.50 BSC 37551fd 24 LT3755/LT3755-1/LT3755-2 Revision History (Revision history begins at Rev D) REV DATE DESCRIPTION PAGE NUMBER D 03/10 Revised Entire Data Sheet to Include H-Grade 1-26 37551fd Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 25 LT3755/LT3755-1/LT3755-2 Typical Application Buck-Boost LED Driver for Automotive VIN 6V TO 36V Efficiency vs VIN 100 4.7µF s2 LTC4440-5 VCC BOOST TG GND TS INP 330k D1 SHDN/UVLO VREF 383k M2 GATE 0.025Ω LT3755-2 47k 1M 100k OPENLED PWM SS ISN RT PWMOUT VC GND INTVCC 28.7k 375kHz 1% 88 84 4.7µF 40k 80 FB ISP 0.01µF 92 SENSE CTRL INTVCC D2 22µF VIN 1M 96 0.22µF M1 EFFICIENCY (%) INTVCC 10k 0.01µF 0.1Ω 0 10 20 VIN (V) 30 40 37551 TA05b 1A INTVCC 4.7µF M1, M2: VISHAY SILICONIX SI7850DP D1, D2: DIODES, INC SBM540 37551 TA05a Related Parts PART NUMBER DESCRIPTION COMMENTS LT3474 36V, 1A (ILED), 2MHz, Step-Down LED Driver VIN: 4V to 36V, VOUT(MAX) = 13.5V, True Color PWM Dimming = 400:1, ISD < 1µA, TSSOP16E Package LT3475 Dual 1.5A (ILED), 36V, 2MHz Step-Down LED Driver VIN: 4V to 36V, VOUT(MAX) = 13.5V, True Color PWM Dimming = 3000:1, ISD < 1µA, TSSOP20E Package LT3476 Quad Output 1.5A, 36V, 2MHz High Current LED Driver with 1000:1 Dimming VIN: 2.8V to 16V, VOUT(MAX) = 36V, True Color PWM Dimming = 1000:1, ISD < 10µA, 5mm × 7mm QFN Package LT3477 3A, 42V, 3MHz Boost, Buck-Boost, Buck LED Driver VIN: 2.5V to 25V, VOUT(MAX) = 40V, Dimming = Analog/PWM, ISD < 1µA, QFN and TSSOP20E Packages LT3478/LT3478-1 4.5A, 42V, 2.5MHz High Current LED Driver with 3000:1 Dimming VIN: 2.8V to 36V, VOUT(MAX) = 42V, True Color PWM Dimming = 3000:1, ISD < 3µA, TSSOP16E Package LT3486 Dual 1.3A, 2MHz High Current LED Driver VIN: 2.5V to 24V, VOUT(MAX) = 36V, True Color PWM Dimming = 1000:1, ISD < 1µA, 5mm × 3mm DFN and TSSOP16E Packages LT3496 Triple 0.75A, 2.1MHz, 45V LED Driver VIN: 3V to 30V, VOUT(MAX) = 45V, Dimming = 3000:1, ISD < 1µA, 4mm × 5mm QFN and TSSOP16E Packages LT3517 1.3A, 2.5MHz, 45V LED Driver VIN: 3V to 30V, VOUT(MAX) = 45V, Dimming = 3000:1, ISD < 1µA, 4mm × 4mm QFN and TSSOP16E Packages LT3518 2.3A, 2.5MHz, 45V LED Driver VIN: 3V to 30V, VOUT(MAX) = 45V, Dimming = 3000:1, ISD < 1µA, 4mm × 4mm QFN and TSSOP16E Packages LT3756/LT3756-1/ LT3756-2 100VIN, 100VOUT LED Controller VIN: 6V to 100V, VOUT(MAX) = 100V, True Color PWM Dimming = 3000:1, ISD < 1µA, 3mm × 3mm QFN-16 and MS16E Packages LTC®3783 High Current LED Controller VIN: 3V to 36V, VOUT(MAX) = Ext FET, True Color PWM Dimming = 3000:1, ISD < 20µA, 5mm × 4mm QFN10 and TSSOP16E Packages 37551fd 26 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LT 0310 REV D • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2008