View detail for 8051 Microcontroller Instruction Set

Section 1
8051 Microcontroller Instruction Set
For interrupt response time information, refer to the hardware description chapter.
Instructions that Affect Flag Settings(1)
Instruction
Flag
Instruction
Flag
C
OV
AC
ADD
X
X
X
CLR C
O
ADDC
X
X
X
CPL C
X
SUBB
X
X
X
ANL C,bit
X
MUL
O
X
ANL C,/bit
X
DIV
O
X
ORL C,bit
X
DA
X
ORL C,/bit
X
RRC
X
MOV C,bit
X
RLC
X
CJNE
X
SETB C
1
Note:
C
OV
AC
1. Operations on SFR byte address 208 or bit addresses 209-215 (that is, the PSW or bits in the PSW) also affect flag settings.
The Instruction Set and Addressing Modes
Rn
Register R7-R0 of the currently selected Register Bank.
direct
8-bit internal data location’s address. This could be an Internal Data RAM location (0-127) or a SFR [i.e., I/O
port, control register, status register, etc. (128-255)].
@R i
8-bit internal data RAM location (0-255) addressed indirectly through register R1or R0.
#data
8-bit constant included in instruction.
#data 16
16-bit constant included in instruction.
addr 16
16-bit destination address. Used by LCALL and LJMP. A branch can be anywhere within the 64K byte Program
Memory address space.
addr 11
11-bit destination address. Used by ACALL and AJMP. The branch will be within the same 2K byte page of
program memory as the first byte of the following instruction.
rel
Signed (two’s complement) 8-bit offset byte. Used by SJMP and all conditional jumps. Range is -128 to +127
bytes relative to first byte of the following instruction.
bit
Direct Addressed bit in Internal Data RAM or Special Function Register.
Atmel 8051 Microcontrollers Hardware
1
0509C–8051–07/06
Table 1-1. Instruction Set Summary
0
1
2
3
4
5
6
7
0
NOP
JBC
bit,rel
[3B, 2C]
JB
bit, rel
[3B, 2C]
JNB
bit, rel
[3B, 2C]
JC
rel
[2B, 2C]
JNC
rel
[2B, 2C]
JZ
rel
[2B, 2C]
JNZ
rel
[2B, 2C]
1
AJMP
(P0)
[2B, 2C]
ACALL
(P0)
[2B, 2C]
AJMP
(P1)
[2B, 2C]
ACALL
(P1)
[2B, 2C]
AJMP
(P2)
[2B, 2C]
ACALL
(P2)
[2B, 2C]
AJMP
(P3)
[2B, 2C]
ACALL
(P3)
[2B, 2C]
2
LJMP
addr16
[3B, 2C]
LCALL
addr16
[3B, 2C]
RET
[2C]
RETI
[2C]
ORL
dir, A
[2B]
ANL
dir, A
[2B]
XRL
dir, a
[2B]
ORL
C, bit
[2B, 2C]
3
RR
A
RRC
A
RL
A
RLC
A
ORL
dir, #data
[3B, 2C]
ANL
dir, #data
[3B, 2C]
XRL
dir, #data
[3B, 2C]
JMP
@A + DPTR
[2C]
4
INC
A
DEC
A
ADD
A, #data
[2B]
ADDC
A, #data
[2B]
ORL
A, #data
[2B]
ANL
A, #data
[2B]
XRL
A, #data
[2B]
MOV
A, #data
[2B]
5
INC
dir
[2B]
DEC
dir
[2B]
ADD
A, dir
[2B]
ADDC
A, dir
[2B]
ORL
A, dir
[2B]
ANL
A, dir
[2B]
XRL
A, dir
[2B]
MOV
dir, #data
[3B, 2C]
6
INC
@R0
DEC
@R0
ADD
A, @R0
ADDC
A, @R0
ORL
A, @R0
ANL
A, @R0
XRL
A, @R0
MOV
@R0, @data
[2B]
7
INC
@R1
DEC
@R1
ADD
A, @R1
ADDC
A, @R1
ORL
A, @R1
ANL
A, @R1
XRL
A, @R1
MOV
@R1, #data
[2B]
8
INC
R0
DEC
R0
ADD
A, R0
ADDC
A, R0
ORL
A, R0
ANL
A, R0
XRL
A, R0
MOV
R0, #data
[2B]
9
INC
R1
DEC
R1
ADD
A, R1
ADDC
A, R1
ORL
A, R1
ANL
A, R1
XRL
A, R1
MOV
R1, #data
[2B]
A
INC
R2
DEC
R2
ADD
A, R2
ADDC
A, R2
ORL
A, R2
ANL
A, R2
XRL
A, R2
MOV
R2, #data
[2B]
B
INC
R3
DEC
R3
ADD
A, R3
ADDC
A, R3
ORL
A, R3
ANL
A, R3
XRL
A, R3
MOV
R3, #data
[2B]
C
INC
R4
DEC
R4
ADD
A, R4
ADDC
A, R4
ORL
A, R4
ANL
A, R4
XRL
A, R4
MOV
R4, #data
[2B]
D
INC
R5
DEC
R5
ADD
A, R5
ADDC
A, R5
ORL
A, R5
ANL
A, R5
XRL
A, R5
MOV
R5, #data
[2B]
E
INC
R6
DEC
R6
ADD
A, R6
ADDC
A, R6
ORL
A, R6
ANL
A, R6
XRL
A, R6
MOV
R6, #data
[2B]
F
INC
R7
DEC
R7
ADD
A, R7
ADDC
A, R7
ORL
A, R7
ANL
A, R7
XRL
A, R7
MOV
R7, #data
[2B]
Note:
Key: [2B] = 2 Byte, [3B] = 3 Byte, [2C] = 2 Cycle, [4C] = 4 Cycle, Blank = 1 byte/1 cycle
2
0509C–8051–07/06
Table 1-2. Instruction Set Summary (Continued)
8
9
A
B
C
D
E
F
0
SJMP
REL
[2B, 2C]
MOV
DPTR,#
data 16
[3B, 2C]
ORL
C, /bit
[2B, 2C]
ANL
C, /bit
[2B, 2C]
PUSH
dir
[2B, 2C]
POP
dir
[2B, 2C]
MOVX A,
@DPTR
[2C]
MOVX
@DPTR, A
[2C]
1
AJMP
(P4)
[2B, 2C]
ACALL
(P4)
[2B, 2C]
AJMP
(P5)
[2B, 2C]
ACALL
(P5)
[2B, 2C]
AJMP
(P6)
[2B, 2C]
ACALL
(P6)
[2B, 2C]
AJMP
(P7)
[2B, 2C]
ACALL
(P7)
[2B, 2C]
2
ANL
C, bit
[2B, 2C]
MOV
bit, C
[2B, 2C]
MOV
C, bit
[2B]
CPL
bit
[2B]
CLR
bit
[2B]
SETB
bit
[2B]
MOVX
A, @R0
[2C]
MOVX
wR0, A
[2C]
3
MOVC A,
@A + PC
[2C]
MOVC A,
@A + DPTR
[2C]
INC
DPTR
[2C]
CPL
C
CLR
C
SETB
C
MOVX
A, @RI
[2C]
MOVX
@RI, A
[2C]
4
DIV
AB
[2B, 4C]
SUBB
A, #data
[2B]
MUL
AB
[4C]
CJNE A,
#data, rel
[3B, 2C]
SWAP
A
DA
A
CLR
A
CPL
A
5
MOV
dir, dir
[3B, 2C]
SUBB
A, dir
[2B]
CJNE
A, dir, rel
[3B, 2C]
XCH
A, dir
[2B]
DJNZ
dir, rel
[3B, 2C]
MOV
A, dir
[2B]
MOV
dir, A
[2B]
6
MOV
dir, @R0
[2B, 2C]
SUBB
A, @R0
MOV
@R0, dir
[2B, 2C]
CJNE
@R0, #data, rel
[3B, 2C]
XCH
A, @R0
XCHD
A, @R0
MOV
A, @R0
MOV
@R0, A
7
MOV
dir, @R1
[2B, 2C]
SUBB
A, @R1
MOV
@R1, dir
[2B, 2C]
CJNE
@R1, #data, rel
[3B, 2C]
XCH
A, @R1
XCHD
A, @R1
MOV
A, @R1
MOV
@R1, A
8
MOV
dir, R0
[2B, 2C]
SUBB
A, R0
MOV
R0, dir
[2B, 2C]
CJNE
R0, #data, rel
[3B, 2C]
XCH
A, R0
DJNZ
R0, rel
[2B, 2C]
MOV
A, R0
MOV
R0, A
9
MOV
dir, R1
[2B, 2C]
SUBB
A, R1
MOV
R1, dir
[2B, 2C]
CJNE
R1, #data, rel
[3B, 2C]
XCH
A, R1
DJNZ
R1, rel
[2B, 2C]
MOV
A, R1
MOV
R1, A
A
MOV
dir, R2
[2B, 2C]
SUBB
A, R2
MOV
R2, dir
[2B, 2C]
CJNE
R2, #data, rel
[3B, 2C]
XCH
A, R2
DJNZ
R2, rel
[2B, 2C]
MOV
A, R2
MOV
R2, A
B
MOV
dir, R3
[2B, 2C]
SUBB
A, R3
MOV
R3, dir
[2B, 2C]
CJNE
R3, #data, rel
[3B, 2C]
XCH
A, R3
DJNZ
R3, rel
[2B, 2C]
MOV
A, R3
MOV
R3, A
C
MOV
dir, R4
[2B, 2C]
SUBB
A, R4
MOV
R4, dir
[2B, 2C]
CJNE
R4, #data, rel
[3B, 2C]
XCH
A, R4
DJNZ
R4, rel
[2B, 2C]
MOV
A, R4
MOV
R4, A
D
MOV
dir, R5
[2B, 2C]
SUBB
A, R5
MOV
R5, dir
[2B, 2C]
CJNE
R5, #data, rel
[3B, 2C]
XCH
A, R5
DJNZ
R5, rel
[2B, 2C]
MOV
A, R5
MOV
R5, A
E
MOV
dir, R6
[2B, 2C]
SUBB
A, R6
MOV
R6, dir
[2B, 2C]
CJNE
R6, #data, rel
[3B, 2C]
XCH
A, R6
DJNZ
R6, rel
[2B, 2C]
MOV
A, R6
MOV
R6. A
F
MOV
dir, R7
[2B, 2C]
SUBB
A, R7
MOV
R7, dir
[2B, 2C]
CJNE
R7, #data, rel
[3B, 2C]
XCH
A, R7
DJNZ
R7, rel
[2B, 2C]
MOV
A, R7
MOV
R7, A
Note:
Key: [2B] = 2 Byte, [3B] = 3 Byte, [2C] = 2 Cycle, [4C] = 4 Cycle, Blank = 1 byte/1 cycle
3
0509C–8051–07/06
8051 Microcontroller Instruction Set
Table 1-3. AT89 Instruction Set Summary(1)
Mnemonic
Description
Byte
Oscillator
Period
ARITHMETIC OPERATIONS
Mnemonic
Description
Byte
Oscillator
Period
LOGICAL OPERATIONS
ADD
A,Rn
Add register to
Accumulator
1
12
ANL
A,Rn
AND Register to
Accumulator
1
12
ADD
A,direct
Add direct byte to
Accumulator
2
12
ANL
A,direct
AND direct byte to
Accumulator
2
12
ADD
A,@Ri
Add indirect RAM to
Accumulator
1
12
ANL
A,@Ri
AND indirect RAM to
Accumulator
1
12
ADD
A,#data
Add immediate data to
Accumulator
2
12
ANL
A,#data
AND immediate data to
Accumulator
2
12
ADDC
A,Rn
Add register to
Accumulator with Carry
1
12
ANL
direct,A
AND Accumulator to
direct byte
2
12
ADDC
A,direct
Add direct byte to
Accumulator with Carry
2
12
ANL
direct,#data
AND immediate data to
direct byte
3
24
ADDC
A,@Ri
Add indirect RAM to
Accumulator with Carry
1
12
ORL
A,Rn
OR register to
Accumulator
1
12
ADDC
A,#data
Add immediate data to
Acc with Carry
2
12
ORL
A,direct
OR direct byte to
Accumulator
2
12
SUBB
A,Rn
Subtract Register from
Acc with borrow
1
12
ORL
A,@Ri
OR indirect RAM to
Accumulator
1
12
SUBB
A,direct
Subtract direct byte from
Acc with borrow
2
12
ORL
A,#data
OR immediate data to
Accumulator
2
12
SUBB
A,@Ri
Subtract indirect RAM
from ACC with borrow
1
12
ORL
direct,A
OR Accumulator to
direct byte
2
12
SUBB
A,#data
Subtract immediate data
from Acc with borrow
2
12
ORL
direct,#data
OR immediate data to
direct byte
3
24
INC
A
Increment Accumulator
1
12
XRL
A,Rn
1
12
INC
Rn
Increment register
1
12
Exclusive-OR register to
Accumulator
INC
direct
Increment direct byte
2
12
XRL
A,direct
Exclusive-OR direct byte
to Accumulator
2
12
INC
@Ri
Increment direct RAM
1
12
XRL
A,@Ri
12
A
Decrement Accumulator
1
12
Exclusive-OR indirect
RAM to Accumulator
1
DEC
DEC
Rn
Decrement Register
1
12
XRL
A,#data
Exclusive-OR immediate
data to Accumulator
2
12
DEC
direct
Decrement direct byte
2
12
XRL
direct,A
12
@Ri
Decrement indirect RAM
1
12
INC
DPTR
Increment Data Pointer
1
24
Exclusive-OR
Accumulator to direct
byte
2
DEC
MUL
AB
Multiply A & B
1
48
XRL
direct,#data
Exclusive-OR immediate
data to direct byte
3
24
DIV
AB
Divide A by B
1
48
CLR
A
Clear Accumulator
1
12
DA
A
Decimal Adjust
Accumulator
1
12
CPL
A
Complement
Accumulator
1
12
RL
A
Rotate Accumulator Left
1
12
RLC
A
Rotate Accumulator Left
through the Carry
1
12
Note:
1. All mnemonics copyrighted © Intel Corp., 1980.
LOGICAL OPERATIONS (continued)
Atmel 8051 Microcontrollers Hardware Manual
1-4
0509C–8051–07/06
8051 Microcontroller Instruction Set
Mnemonic
Description
RR
A
RRC
Mnemonic
Description
12
MOVX @Ri,A
1
12
1
12
Byte
Oscillator
Period
Rotate Accumulator
Right
1
A
Rotate Accumulator
Right through the Carry
SWAP A
Swap nibbles within the
Accumulator
DATA TRANSFER
MOV
MOV
MOV
A,Rn
A,direct
A,@Ri
Move register to
Accumulator
1
Move direct byte to
Accumulator
2
Move indirect RAM to
Accumulator
1
Move Acc to External
RAM (8-bit addr)
1
24
MOVX @DPTR,A
Move Acc to External
RAM (16-bit addr)
1
24
PUSH
direct
Push direct byte onto
stack
2
24
POP
direct
Pop direct byte from
stack
2
24
XCH
A,Rn
Exchange register with
Accumulator
1
12
XCH
A,direct
Exchange direct byte
with Accumulator
2
12
XCH
A,@Ri
Exchange indirect RAM
with Accumulator
1
12
XCHD
A,@Ri
Exchange low-order
Digit indirect RAM with
Acc
1
12
12
12
A,#data
Move immediate data to
Accumulator
2
12
MOV
Rn,A
Move Accumulator to
register
1
12
MOV
Rn,direct
Move direct byte to
register
2
24
MOV
Rn,#data
Move immediate data to
register
2
12
MOV
direct,A
Move Accumulator to
direct byte
2
12
MOV
direct,Rn
Move register to direct
byte
2
24
MOV
direct,direct
Move direct byte to direct
3
24
MOV
direct,@Ri
Move indirect RAM to
direct byte
2
MOV
direct,#data
Move immediate data to
direct byte
MOV
@Ri,A
MOV
MOV
Oscillator
Period
12
MOV
MOV
Byte
BOOLEAN VARIABLE MANIPULATION
CLR
C
Clear Carry
1
12
CLR
bit
Clear direct bit
2
12
SETB
C
Set Carry
1
12
SETB
bit
Set direct bit
2
12
CPL
C
Complement Carry
1
12
CPL
bit
Complement direct bit
2
12
ANL
C,bit
AND direct bit to CARRY
2
24
24
ANL
C,/bit
AND complement of
direct bit to Carry
2
24
3
24
ORL
C,bit
OR direct bit to Carry
2
24
ORL
C,/bit
24
1
12
OR complement of direct
bit to Carry
2
Move Accumulator to
indirect RAM
MOV
C,bit
Move direct bit to Carry
2
12
@Ri,direct
Move direct byte to
indirect RAM
2
24
MOV
bit,C
Move Carry to direct bit
2
24
@Ri,#data
Move immediate data to
indirect RAM
2
DPTR,#data16 Load Data Pointer with a
16-bit constant
3
24
12
MOVC A,@A+DPTR
Move Code byte relative
to DPTR to Acc
1
24
MOVC A,@A+PC
Move Code byte relative
to PC to Acc
1
24
MOVX A,@Ri
Move External RAM (8bit addr) to Acc
1
24
1-5
0509C–8051–07/06
Move Exernal RAM (16bit addr) to Acc
rel
Jump if Carry is set
2
24
JNC
rel
Jump if Carry not set
2
24
JB
bit,rel
Jump if direct Bit is set
3
24
JNB
bit,rel
Jump if direct Bit is Not
set
3
24
JBC
bit,rel
Jump if direct Bit is set &
clear bit
3
24
Absolute Subroutine Call
2
24
LCALL addr16
Long Subroutine Call
3
24
RET
Return from Subroutine
1
24
PROGRAM BRANCHING
ACAL
L
DATA TRANSFER (continued)
MOVX A,@DPTR
JC
1
24
addr11
Atmel 8051 Microcontrollers Hardware Manual
8051 Microcontroller Instruction Set
Mnemonic
Description
Byte
Oscillator
Period
RETI
Return from
interrupt
1
24
AJMP
addr11
Absolute Jump
2
24
LJMP
addr16
Long Jump
3
24
SJMP
rel
Short Jump (relative
addr)
2
24
JMP
@A+DPTR
Jump indirect relative to
the DPTR
1
24
JZ
rel
Jump if Accumulator is
Zero
2
24
JNZ
rel
Jump if Accumulator is
Not Zero
2
24
CJNE
A,direct,rel
Compare direct byte to
Acc and Jump if Not
Equal
3
24
CJNE
A,#data,rel
Compare immediate to
Acc and Jump if Not
Equal
3
24
CJNE
Rn,#data,rel
Compare immediate to
register and Jump if Not
Equal
3
24
CJNE
@Ri,#data,rel
Compare immediate to
indirect and Jump if Not
Equal
3
24
DJNZ
Rn,rel
Decrement register and
Jump if Not Zero
2
24
DJNZ
direct,rel
Decrement direct byte
and Jump if Not Zero
3
24
No Operation
1
12
NOP
Atmel 8051 Microcontrollers Hardware Manual
1-6
0509C–8051–07/06
8051 Microcontroller Instruction Set
Table 1-4. Instruction Opcodes in Hexadecimal Order
Hex
Code
Number
of Bytes
Mnemonic
Operands
Hex
Code
Number
of Bytes
Mnemonic
Operands
00
1
NOP
26
1
ADD
A,@R0
01
2
AJMP
code addr
27
1
ADD
A,@R1
02
3
LJMP
code addr
28
1
ADD
A,R0
03
1
RR
A
29
1
ADD
A,R1
04
1
INC
A
2A
1
ADD
A,R2
05
2
INC
data addr
2B
1
ADD
A,R3
06
1
INC
@R0
2C
1
ADD
A,R4
07
1
INC
@R1
2D
1
ADD
A,R5
08
1
INC
R0
2E
1
ADD
A,R6
09
1
INC
R1
2F
1
ADD
A,R7
0A
1
INC
R2
30
3
JNB
bit addr,code addr
0B
1
INC
R3
31
2
ACALL
code addr
0C
1
INC
R4
32
1
RETI
0D
1
INC
R5
33
1
RLC
A
0E
1
INC
R6
34
2
ADDC
A,#data
0F
1
INC
R7
35
2
ADDC
A,data addr
10
3
JBC
bit addr,code addr
36
1
ADDC
A,@R0
11
2
ACALL
code addr
37
1
ADDC
A,@R1
12
3
LCALL
code addr
38
1
ADDC
A,R0
13
1
RRC
A
39
1
ADDC
A,R1
14
1
DEC
A
3A
1
ADDC
A,R2
15
2
DEC
data addr
3B
1
ADDC
A,R3
16
1
DEC
@R0
3C
1
ADDC
A,R4
17
1
DEC
@R1
3D
1
ADDC
A,R5
18
1
DEC
R0
3E
1
ADDC
A,R6
19
1
DEC
R1
3F
1
ADDC
A,R7
1A
1
DEC
R2
40
2
JC
code addr
1B
1
DEC
R3
41
2
AJMP
code addr
1C
1
DEC
R4
42
2
ORL
data addr,A
1D
1
DEC
R5
43
3
ORL
data addr,#data
1E
1
DEC
R6
44
2
ORL
A,#data
1F
1
DEC
R7
45
2
ORL
A,data addr
20
3
JB
bit addr,code addr
46
1
ORL
A,@R0
21
2
AJMP
code addr
47
1
ORL
A,@R1
22
1
RET
48
1
ORL
A,R0
23
1
RL
A
49
1
ORL
A,R1
24
2
ADD
A,#data
4A
1
ORL
A,R2
25
2
ADD
A,data addr
1-7
0509C–8051–07/06
Atmel 8051 Microcontrollers Hardware Manual
8051 Microcontroller Instruction Set
Hex
Code
Number
of Bytes
Mnemonic
Operands
Hex
Code
Number
of Bytes
Mnemonic
Operands
4B
1
ORL
A,R3
71
2
ACALL
code addr
4C
1
ORL
A,R4
72
2
ORL
C,bit addr
4D
1
ORL
A,R5
73
1
JMP
@A+DPTR
4E
1
ORL
A,R6
74
2
MOV
A,#data
4F
1
ORL
A,R7
75
3
MOV
data addr,#data
50
2
JNC
code addr
76
2
MOV
@R0,#data
51
2
ACALL
code addr
77
2
MOV
@R1,#data
52
2
ANL
data addr,A
78
2
MOV
R0,#data
53
3
ANL
data addr,#data
79
2
MOV
R1,#data
54
2
ANL
A,#data
7A
2
MOV
R2,#data
55
2
ANL
A,data addr
7B
2
MOV
R3,#data
56
1
ANL
A,@R0
7C
2
MOV
R4,#data
57
1
ANL
A,@R1
7D
2
MOV
R5,#data
58
1
ANL
A,R0
7E
2
MOV
R6,#data
59
1
ANL
A,R1
7F
2
MOV
R7,#data
5A
1
ANL
A,R2
80
2
SJMP
code addr
5B
1
ANL
A,R3
81
2
AJMP
code addr
5C
1
ANL
A,R4
82
2
ANL
C,bit addr
5D
1
ANL
A,R5
83
1
MOVC
A,@A+PC
5E
1
ANL
A,R6
84
1
DIV
AB
5F
1
ANL
A,R7
85
3
MOV
data addr,data addr
60
2
JZ
code addr
86
2
MOV
data addr,@R0
61
2
AJMP
code addr
87
2
MOV
data addr,@R1
62
2
XRL
data addr,A
88
2
MOV
data addr,R0
63
3
XRL
data addr,#data
89
2
MOV
data addr,R1
64
2
XRL
A,#data
8A
2
MOV
data addr,R2
65
2
XRL
A,data addr
8B
2
MOV
data addr,R3
66
1
XRL
A,@R0
8C
2
MOV
data addr,R4
67
1
XRL
A,@R1
8D
2
MOV
data addr,R5
68
1
XRL
A,R0
8E
2
MOV
data addr,R6
69
1
XRL
A,R1
8F
2
MOV
data addr,R7
6A
1
XRL
A,R2
90
3
MOV
DPTR,#data
6B
1
XRL
A,R3
91
2
ACALL
code addr
6C
1
XRL
A,R4
92
2
MOV
bit addr,C
6D
1
XRL
A,R5
93
1
MOVC
A,@A+DPTR
6E
1
XRL
A,R6
94
2
SUBB
A,#data
6F
1
XRL
A,R7
95
2
SUBB
A,data addr
70
2
JNZ
code addr
96
1
SUBB
A,@R0
Atmel 8051 Microcontrollers Hardware Manual
1-8
0509C–8051–07/06
8051 Microcontroller Instruction Set
Hex
Code
Number
of Bytes
Mnemonic
Operands
Hex
Code
Number
of Bytes
Mnemonic
Operands
97
1
SUBB
A,@R1
BD
3
CJNE
R5,#data,code addr
98
1
SUBB
A,R0
BE
3
CJNE
R6,#data,code addr
99
1
SUBB
A,R1
BF
3
CJNE
R7,#data,code addr
9A
1
SUBB
A,R2
C0
2
PUSH
data addr
9B
1
SUBB
A,R3
C1
2
AJMP
code addr
9C
1
SUBB
A,R4
C2
2
CLR
bit addr
9D
1
SUBB
A,R5
C3
1
CLR
C
9E
1
SUBB
A,R6
C4
1
SWAP
A
9F
1
SUBB
A,R7
C5
2
XCH
A,data addr
A0
2
ORL
C,/bit addr
C6
1
XCH
A,@R0
A1
2
AJMP
code addr
C7
1
XCH
A,@R1
A2
2
MOV
C,bit addr
C8
1
XCH
A,R0
A3
1
INC
DPTR
C9
1
XCH
A,R1
A4
1
MUL
AB
CA
1
XCH
A,R2
CB
1
XCH
A,R3
A5
reserved
A6
2
MOV
@R0,data addr
CC
1
XCH
A,R4
A7
2
MOV
@R1,data addr
CD
1
XCH
A,R5
A8
2
MOV
R0,data addr
CE
1
XCH
A,R6
A9
2
MOV
R1,data addr
CF
1
XCH
A,R7
AA
2
MOV
R2,data addr
D0
2
POP
data addr
AB
2
MOV
R3,data addr
D1
2
ACALL
code addr
AC
2
MOV
R4,data addr
D2
2
SETB
bit addr
AD
2
MOV
R5,data addr
D3
1
SETB
C
AE
2
MOV
R6,data addr
D4
1
DA
A
AF
2
MOV
R7,data addr
D5
3
DJNZ
data addr,code addr
B0
2
ANL
C,/bit addr
D6
1
XCHD
A,@R0
B1
2
ACALL
code addr
D7
1
XCHD
A,@R1
B2
2
CPL
bit addr
D8
2
DJNZ
R0,code addr
B3
1
CPL
C
D9
2
DJNZ
R1,code addr
B4
3
CJNE
A,#data,code addr
DA
2
DJNZ
R2,code addr
B5
3
CJNE
A,data addr,code addr
DB
2
DJNZ
R3,code addr
B6
3
CJNE
@R0,#data,code addr
DC
2
DJNZ
R4,code addr
B7
3
CJNE
@R1,#data,code addr
DD
2
DJNZ
R5,code addr
B8
3
CJNE
R0,#data,code addr
DE
2
DJNZ
R6,code addr
B9
3
CJNE
R1,#data,code addr
DF
2
DJNZ
R7,code addr
BA
3
CJNE
R2,#data,code addr
E0
1
MOVX
A,@DPTR
BB
3
CJNE
R3,#data,code addr
E1
2
AJMP
code addr
BC
3
CJNE
R4,#data,code addr
E2
1
MOVX
A,@R0
1-9
0509C–8051–07/06
Atmel 8051 Microcontrollers Hardware Manual
8051 Microcontroller Instruction Set
Hex
Code
Number
of Bytes
Mnemonic
Operands
E3
1
MOVX
A,@R1
E4
1
CLR
A
E5
2
MOV
A,data addr
E6
1
MOV
A,@R0
E7
1
MOV
A,@R1
E8
1
MOV
A,R0
E9
1
MOV
A,R1
EA
1
MOV
A,R2
EB
1
MOV
A,R3
EC
1
MOV
A,R4
ED
1
MOV
A,R5
EE
1
MOV
A,R6
EF
1
MOV
A,R7
F0
1
MOVX
@DPTR,A
F1
2
ACALL
code addr
F2
1
MOVX
@R0,A
F3
1
MOVX
@R1,A
F4
1
CPL
A
F5
2
MOV
data addr,A
F6
1
MOV
@R0,A
F7
1
MOV
@R1,A
F8
1
MOV
R0,A
F9
1
MOV
R1,A
FA
1
MOV
R2,A
FB
1
MOV
R3,A
FC
1
MOV
R4,A
FD
1
MOV
R5,A
FE
1
MOV
R6,A
FF
1
MOV
R7,A
Atmel 8051 Microcontrollers Hardware Manual
1-10
0509C–8051–07/06
1.1
Instruction Definitions
ACALL addr11
Function: Absolute Call
Description: ACALL unconditionally calls a subroutine located at the indicated address. The instruction increments the PC
twice to obtain the address of the following instruction, then pushes the 16-bit result onto the stack (low-order
byte first) and increments the Stack Pointer twice. The destination address is obtained by successively
concatenating the five high-order bits of the incremented PC, opcode bits 7 through 5, and the second byte of
the instruction. The subroutine called must therefore start within the same 2 K block of the program memory as
the first byte of the instruction following ACALL. No flags are affected.
Example: Initially SP equals 07H. The label SUBRTN is at program memory location 0345 H. After executing the following
instruction,
ACALL
SUBRTN
at location 0123H, SP contains 09H, internal RAM locations 08H and 09H will contain 25H and 01H, respectively,
and the PC contains 0345H.
Bytes: 2
Cycles: 2
Encoding: a10
a9
a8
1
0
0
0
1
a7
a6
a5
a4
a3
a2
a1
a0
Operation: ACALL
(PC) ← (PC) + 2
(SP) ← (SP) + 1
((SP)) ← (PC7-0)
(SP) ← (SP) + 1
((SP)) ← (PC15-8)
(PC10-0) ← page address
11
0509C–8051–07/06
ADD
A,<src-byte>
Function: Add
Description: ADD adds the byte variable indicated to the Accumulator, leaving the result in the Accumulator. The carry and
auxiliary-carry flags are set, respectively, if there is a carry-out from bit 7 or bit 3, and cleared otherwise. When
adding unsigned integers, the carry flag indicates an overflow occurred.
OV is set if there is a carry-out of bit 6 but not out of bit 7, or a carry-out of bit 7 but not bit 6; otherwise, OV is
cleared. When adding signed integers, OV indicates a negative number produced as the sum of two positive
operands, or a positive sum from two negative operands.
Four source operand addressing modes are allowed: register, direct, register-indirect, or immediate.
Example: The Accumulator holds 0C3H (1100001lB), and register 0 holds 0AAH (10101010B). The following instruction,
ADD
A,R0
leaves 6DH (01101101B) in the Accumulator with the AC flag cleared and both the carry flag and OV set to 1.
ADD A,Rn
Bytes: 1
Cycles: 1
Encoding:
0
0
1
0
1
r
r
r
0
0
1
0
1
0
0
1
1
i
0
0
1
0
0
Operation: ADD
(A) ← (A) + (R n)
ADD A,direct
Bytes: 2
Cycles: 1
Encoding:
0
0
1
direct address
Operation: ADD
(A) ← (A) + (direct)
ADD A,@Ri
Bytes: 1
Cycles: 1
Encoding:
0
0
1
Operation: ADD
(A) ← (A) + ((Ri))
ADD A,#data
Bytes: 2
Cycles: 1
Encoding:
0
0
1
immediate data
Operation: ADD
(A) ← (A) + #data
12
0509C–8051–07/06
ADDC A, <src-byte>
Function: Add with Carry
Description: ADDC simultaneously adds the byte variable indicated, the carry flag and the Accumulator contents, leaving the
result in the Accumulator. The carry and auxiliary-carry flags are set respectively, if there is a carry-out from bit 7
or bit 3, and cleared otherwise. When adding unsigned integers, the carry flag indicates an overflow occurred.
OV is set if there is a carry-out of bit 6 but not out of bit 7, or a carry-out of bit 7 but not out of bit 6; otherwise OV
is cleared. When adding signed integers, OV indicates a negative number produced as the sum of two positive
operands or a positive sum from two negative operands.
Four source operand addressing modes are allowed: register, direct, register-indirect, or immediate.
Example: The Accumulator holds 0C3H (11000011B) and register 0 holds 0AAH (10101010B) with the carry flag set. The
following instruction,
ADDC
A,R0
leaves 6EH (01101110B) in the Accumulator with AC cleared and both the Carry flag and OV set to 1.
ADDC A,R n
Bytes: 1
Cycles: 1
Encoding:
0
0
1
1
1
r
r
r
0
1
0
1
0
1
1
i
0
1
0
0
Operation: ADDC
(A) ← (A) + (C) + (Rn)
ADDC A,direct
Bytes: 2
Cycles: 1
Encoding:
0
0
1
1
direct address
Operation: ADDC
(A) ← (A) + (C) + (direct)
ADDC A,@R i
Bytes: 1
Cycles: 1
Encoding:
0
0
1
1
Operation: ADDC
(A) ← (A) + (C) + ((R i))
ADDC A,#data
Bytes: 2
Cycles: 1
Encoding:
0
0
1
1
immediate data
Operation: ADDC
(A) ← (A) + (C) + #data
13
0509C–8051–07/06
AJMP addr11
Function: Absolute Jump
Description: AJMP transfers program execution to the indicated address, which is formed at run-time by concatenating the
high-order five bits of the PC (after incrementing the PC twice), opcode bits 7 through 5, and the second byte of
the instruction. The destination must therfore be within the same 2 K block of program memory as the first byte
of the instruction following AJMP.
Example: The label JMPADR is at program memory location 0123H. The following instruction,
AJMP
JMPADR
is at location 0345H and loads the PC with 0123H.
Bytes: 2
Cycles: 2
Encoding: a10
a9
a8
0
0
0
0
1
a7
a6
a5
a4
a3
a2
a1
a0
Operation: AJMP
(PC) ← (PC) + 2
(PC10-0) ← page address
ANL
<dest-byte>,<src-byte>
Function: Logical-AND for byte variables
Description: ANL performs the bitwise logical-AND operation between the variables indicated and stores the results in the
destination variable. No flags are affected.
The two operands allow six addressing mode combinations. When the destination is the Accumulator, the source
can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the
source can be the Accumulator or immediate data.
Note: When this instruction is used to modify an output port, the value used as the original port data will be read
from the output data latch, not the input pins.
Example: If the Accumulator holds 0C3H (1100001lB), and register 0 holds 55H (01010101B), then the following
instruction,
ANL
A,R0
leaves 41H (01000001B) in the Accumulator.
When the destination is a directly addressed byte, this instruction clears combinations of bits in any RAM
location or hardware register. The mask byte determining the pattern of bits to be cleared would either be a
constant contained in the instruction or a value computed in the Accumulator at run-time. The following
instruction,
ANL
P1,#01110011B
clears bits 7, 3, and 2 of output port 1.
ANL
A,R n
Bytes: 1
Cycles: 1
Encoding:
0
1
Operation: ANL
(A) ← (A)
0
1
1
r
r
r
∧ (Rn)
14
0509C–8051–07/06
ANL
A,direct
Bytes: 2
Cycles: 1
Encoding:
0
1
Operation: ANL
(A) ← (A)
ANL
0
1
0
1
0
1
direct address
1
0
1
1
i
1
0
1
0
0
immediate data
1
0
0
1
0
direct address
0
0
1
1
direct address
∧ (direct)
A,@R i
Bytes: 1
Cycles: 1
Encoding:
0
1
Operation: ANL
(A) ← (A)
ANL
0
∧ ((Ri))
A,#data
Bytes: 2
Cycles: 1
Encoding:
0
1
Operation: ANL
(A) ← (A)
ANL
0
∧ #data
direct,A
Bytes: 2
Cycles: 1
Encoding:
0
1
0
Operation: ANL
(direct) ← (direct)
ANL
∧ (A)
direct,#data
Bytes: 3
Cycles: 2
Encoding:
0
1
0
Operation: ANL
(direct) ← (direct)
1
immediate data
∧ #data
15
0509C–8051–07/06
ANL
C,<src-bit>
Function: Logical-AND for bit variables
Description: If the Boolean value of the source bit is a logical 0, then ANL C clears the carry flag; otherwise, this instruction
leaves the carry flag in its current state. A slash ( / ) preceding the operand in the assembly language indicates
that the logical complement of the addressed bit is used as the source value, but the source bit itself is not
affected. No other flags are affected.
Only direct addressing is allowed for the source operand.
Example: Set the carry flag if, and only if, P1.0 = 1, ACC.7 = 1, and OV = 0:
ANL
MOV
C,P1.0
;LOAD CARRY WITH INPUT PIN STATE
ANL
C,ACC.7
;AND CARRY WITH ACCUM. BIT 7
ANL
C,/OV
;AND WITH INVERSE OF OVERFLOW FLAG
C,bit
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: ANL
(C) ← (C)
ANL
0
0
0
0
1
0
bit address
1
0
0
0
0
bit address
∧ (bit)
C,/bit
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: ANL
(C) ← (C)
1
∧
(bit)
16
0509C–8051–07/06
CJNE
<dest-byte>,<src-byte>, rel
Function: Compare and Jump if Not Equal.
Description: CJNE compares the magnitudes of the first two operands and branches if their values are not equal. The branch
destination is computed by adding the signed relative-displacement in the last instruction byte to the PC, after
incrementing the PC to the start of the next instruction. The carry flag is set if the unsigned integer value of
<dest-byte> is less than the unsigned integer value of <src-byte>; otherwise, the carry is cleared. Neither
operand is affected.
The first two operands allow four addressing mode combinations: the Accumulator may be compared with any
directly addressed byte or immediate data, and any indirect RAM location or working register can be compared
with an immediate constant.
Example: The Accumulator contains 34H. Register 7 contains 56H. The first instruction in the sequence,
CJNE
R7, # 60H, NOT_EQ
;
...
.....
;R7 = 60H.
NOT_EQ:
JC
REQ_LOW
;IF R7 < 60H.
;
...
.....
;R7 > 60H.
sets the carry flag and branches to the instruction at label NOT_EQ. By testing the carry flag, this instruction
determines whether R7 is greater or less than 60H.
If the data being presented to Port 1 is also 34H, then the following instruction,
WAIT:
CJNE
A, P1,WAIT
clears the carry flag and continues with the next instruction in sequence, since the Accumulator does equal the
data read from P1. (If some other value was being input on P1, the program loops at this point until the P1 data
changes to 34H.)
CJNE A,direct,rel
Bytes: 3
Cycles: 2
Encoding:
1
0
1
1
0
1
0
1
direct address
rel. address
Operation: (PC) ← (PC) + 3
IF (A) < > (direct)
THEN
(PC) ← (PC) + relative offset
IF (A) < (direct)
THEN
(C) ← 1
ELSE
(C) ← 0
17
0509C–8051–07/06
CJNE A,#data,rel
Bytes: 3
Cycles: 2
Encoding:
1
0
1
1
0
1
0
0
immediate data
rel. address
r
r
r
immediate data
rel. address
1
1
i
immediate data
rel. address
Operation: (PC) ← (PC) + 3
IF (A) < > data
THEN
(PC) ← (PC) + relative offset
IF (A) < data
THEN
(C) ← 1
ELSE
(C) ← 0
CJNE R n,#data,rel
Bytes: 3
Cycles: 2
Encoding:
1
0
1
1
1
Operation: (PC) ← (PC) + 3
IF (Rn) < > data
THEN
(PC) ← (PC) + relative offset
IF (Rn) < data
THEN
(C) ← 1
ELSE
(C) ← 0
CJNE @R i,data,rel
Bytes: 3
Cycles: 2
Encoding:
1
0
1
1
0
Operation: (PC) ← (PC) + 3
IF ((Ri)) < > data
THEN
(PC) ← (PC) + relative offset
IF ((Ri)) < data
THEN
(C) ← 1
ELSE
(C) ← 0
18
0509C–8051–07/06
CLR
A
Function: Clear Accumulator
Description: CLR A clears the Accumulator (all bits set to 0). No flags are affected
Example: The Accumulator contains 5CH (01011100B). The following instruction,CLR Aleaves the Accumulator set to 00H
(00000000B).
Bytes: 1
Cycles: 1
Encoding:
1
1
1
0
0
1
0
0
Operation: CLR
(A) ← 0
CLR
bit
Function: Clear bit
Description: CLR bit clears the indicated bit (reset to 0). No other flags are affected. CLR can operate on the carry flag or any
directly addressable bit.
Example: Port 1 has previously been written with 5DH (01011101B). The following instruction,CLR P1.2 leaves the port set
to 59H (01011001B).
CLR
C
Bytes: 1
Cycles: 1
Encoding:
1
1
0
0
0
0
1
1
1
0
0
0
0
1
0
Operation: CLR
(C) ← 0
CLR
bit
Bytes: 2
Cycles: 1
Encoding:
1
bit address
Operation: CLR
(bit) ← 0
19
0509C–8051–07/06
CPL
A
Function: Complement Accumulator
Description: CPLA logically complements each bit of the Accumulator (one’s complement). Bits which previously contained a
1 are changed to a 0 and vice-versa. No flags are affected.
Example: The Accumulator contains 5CH (01011100B). The following instruction,
CPL
A
leaves the Accumulator set to 0A3H (10100011B).
Bytes: 1
Cycles: 1
Encoding:
1
Operation: CPL
(A) ←
CPL
1
1
1
0
1
0
0
(A)
bit
Function: Complement bit
Description: CPL bit complements the bit variable specified. A bit that had been a 1 is changed to 0 and vice-versa. No other
flags are affected. CLR can operate on the carry or any directly addressable bit.
Note: When this instruction is used to modify an output pin, the value used as the original data is read from the
output data latch, not the input pin.
Example: Port 1 has previously been written with 5BH (01011101B). The following instruction sequence,CPL P1.1CPL
P1.2 leaves the port set to 5BH (01011011B).
CPL
C
Bytes: 1
Cycles: 1
Encoding:
1
0
Operation: CPL
(C) ←
CPL
1
1
0
0
1
1
1
1
0
0
1
0
(C)
bit
Bytes: 2
Cycles: 1
Encoding:
1
Operation: CPL
(bit) ←
0
bit address
(bit)
20
0509C–8051–07/06
DA
A
Function: Decimal-adjust Accumulator for Addition
Description: DA A adjusts the eight-bit value in the Accumulator resulting from the earlier addition of two variables (each in
packed-BCD format), producing two four-bit digits. Any ADD or ADDC instruction may have been used to
perform the addition.
If Accumulator bits 3 through 0 are greater than nine (xxxx1010-xxxx1111), or if the AC flag is one, six is added to
the Accumulator producing the proper BCD digit in the low-order nibble. This internal addition sets the carry flag
if a carry-out of the low-order four-bit field propagates through all high-order bits, but it does not clear the carry
flag otherwise.
If the carry flag is now set, or if the four high-order bits now exceed nine (1010xxxx-1111xxxx), these high-order
bits are incremented by six, producing the proper BCD digit in the high-order nibble. Again, this sets the carry
flag if there is a carry-out of the high-order bits, but does not clear the carry. The carry flag thus indicates if the
sum of the original two BCD variables is greater than 100, allowing multiple precision decimal addition. OV is not
affected.
All of this occurs during the one instruction cycle. Essentially, this instruction performs the decimal conversion by
adding 00H, 06H, 60H, or 66H to the Accumulator, depending on initial Accumulator and PSW conditions.
Note: DA A cannot simply convert a hexadecimal number in the Accumulator to BCD notation, nor does DAA
apply to decimal subtraction.
Example: The Accumulator holds the value 56H (01010110B), representing the packed BCD digits of the decimal number
56. Register 3 contains the value 67H (01100111B), representing the packed BCD digits of the decimal number
67. The carry flag is set. The following instruction sequence
ADDC
A,R3
DA
A
first performs a standard two’s-complement binary addition, resulting in the value 0BEH (10111110) in the
Accumulator. The carry and auxiliary carry flags are cleared.
The Decimal Adjust instruction then alters the Accumulator to the value 24H (00100100B), indicating the packed
BCD digits of the decimal number 24, the low-order two digits of the decimal sum of 56, 67, and the carry-in. The
carry flag is set by the Decimal Adjust instruction, indicating that a decimal overflow occurred. The true sum of
56, 67, and 1 is 124.
BCD variables can be incremented or decremented by adding 01H or 99H. If the Accumulator initially holds 30H
(representing the digits of 30 decimal), then the following instruction sequence,
ADD
A, # 99H
DA
A
leaves the carry set and 29H in the Accumulator, since 30 + 99 = 129. The low-order byte of the sum can be
interpreted to mean 30 - 1 = 29.
Bytes: 1
Cycles: 1
Encoding:
1
1
0
1
0
1
0
0
Operation: DA
-contents of Accumulator are BCD
IF
[[(A3-0 ) > 9]
[(AC) = 1]]
THEN (A3-0) ← (A3-0) + 6
AND
IF
[[(A7-4 ) > 9]
[(C) = 1]]
THEN (A7-4) ← (A7-4) + 6
∨
∨
21
0509C–8051–07/06
DEC
byte
Function: Decrement
Description: DEC byte decrements the variable indicated by 1. An original value of 00H underflows to 0FFH. No flags are
affected. Four operand addressing modes are allowed: accumulator, register, direct, or register-indirect.
Note: When this instruction is used to modify an output port, the value used as the original port data will be read
from the output data latch, not the input pins.
Example: Register 0 contains 7FH (01111111B). Internal RAM locations 7EH and 7FH contain 00H and 40H, respectively.
The following instruction sequence,
DEC
@R0
DEC
R0
DEC
@R0
leaves register 0 set to 7EH and internal RAM locations 7EH and 7FH set to 0FFH and 3FH.
DEC
A
Bytes: 1
Cycles: 1
Encoding:
0
0
0
1
0
1
0
0
0
1
1
r
r
r
1
0
1
0
1
0
1
1
i
Operation: DEC
(A) ← (A) - 1
DEC
Rn
Bytes: 1
Cycles: 1
Encoding:
0
0
Operation: DEC
(Rn) ← (Rn) - 1
DEC
direct
Bytes: 2
Cycles: 1
Encoding:
0
0
0
direct address
Operation: DEC
(direct) ← (direct) - 1
DEC
@R i
Bytes: 1
Cycles: 1
Encoding:
0
0
0
1
Operation: DEC
((Ri)) ← ((Ri)) - 1
22
0509C–8051–07/06
DIV
AB
Function: Divide
Description: DIV AB divides the unsigned eight-bit integer in the Accumulator by the unsigned eight-bit integer in register B.
The Accumulator receives the integer part of the quotient; register B receives the integer remainder. The carry
and OV flags are cleared.
Exception: if B had originally contained 00H, the values returned in the Accumulator and B-register are
undefined and the overflow flag are set. The carry flag is cleared in any case.
Example: The Accumulator contains 251 (0FBH or 11111011B) and B contains 18 (12H or 00010010B). The following
instruction,
DIV
AB
leaves 13 in the Accumulator (0DH or 00001101B) and the value 17 (11H or 00010001B) in B, since
251 = (13 x 18) + 17. Carry and OV are both cleared.
Bytes: 1
Cycles: 4
Encoding:
1
0
0
0
0
1
0
0
Operation: DIV
(A)15-8 ← (A)/(B)
(B)7-0
23
0509C–8051–07/06
DJNZ
<byte>,<rel-addr>
Function: Decrement and Jump if Not Zero
Description: DJNZ decrements the location indicated by 1, and branches to the address indicated by the second operand if
the resulting value is not zero. An original value of 00H underflows to 0FFH. No flags are affected. The branch
destination is computed by adding the signed relative-displacement value in the last instruction byte to the PC,
after incrementing the PC to the first byte of the following instruction.
The location decremented may be a register or directly addressed byte.
Note: When this instruction is used to modify an output port, the value used as the original port data will be read
from the output data latch, not the input pins.
Example: Internal RAM locations 40H, 50H, and 60H contain the values 01H, 70H, and 15H, respectively. The following
instruction sequence,
DJNZ
40H,LABEL_1
DJNZ
50H,LABEL_2
DJNZ
60H,LABEL_3
causes a jump to the instruction at label LABEL_2 with the values 00H, 6FH, and 15H in the three RAM
locations. The first jump was not taken because the result was zero.
This instruction provides a simple way to execute a program loop a given number of times or for adding a
moderate time delay (from 2 to 512 machine cycles) with a single instruction. The following instruction sequence,
TOGGLE:
MOV
R2, # 8
CPL
P1.7
DJNZ
R2,TOGGLE
toggles P1.7 eight times, causing four output pulses to appear at bit 7 of output Port 1. Each pulse lasts three
machine cycles; two for DJNZ and one to alter the pin.
DJNZ R n,rel
Bytes: 2
Cycles: 2
Encoding:
1
1
0
1
1
r
r
r
rel. address
0
1
0
1
direct address
Operation: DJNZ
(PC) ← (PC) + 2
(Rn) ← (Rn) - 1
IF (Rn) > 0 or (Rn) < 0
THEN
(PC) ← (PC) + rel
DJNZ direct,rel
Bytes: 3
Cycles: 2
Encoding:
1
1
0
1
rel. address
Operation: DJNZ
(PC) ← (PC) + 2
(direct) ← (direct) - 1
IF (direct) > 0 or (direct) < 0
THEN
(PC) ← (PC) + rel
24
0509C–8051–07/06
INC
<byte>
Function: Increment
Description: INC increments the indicated variable by 1. An original value of 0FFH overflows to 00H. No flags are affected.
Three addressing modes are allowed: register, direct, or register-indirect.
Note: When this instruction is used to modify an output port, the value used as the original port data will be read
from the output data latch, not the input pins.
Example: Register 0 contains 7EH (011111110B). Internal RAM locations 7EH and 7FH contain 0FFH and 40H,
respectively. The following instruction sequence,
INC
@R0
INC
R0
INC
@R0
leaves register 0 set to 7FH and internal RAM locations 7EH and 7FH holding 00H and 41H, respectively.
INC
A
Bytes: 1
Cycles: 1
Encoding:
0
0
0
0
0
1
0
0
0
0
1
r
r
r
0
0
1
0
1
0
1
1
i
Operation: INC
(A) ← (A) + 1
INC
Rn
Bytes: 1
Cycles: 1
Encoding:
0
0
Operation: INC
(Rn) ← (Rn) + 1
INC
direct
Bytes: 2
Cycles: 1
Encoding:
0
0
0
direct address
Operation: INC
(direct) ← (direct) + 1
INC
@R i
Bytes: 1
Cycles: 1
Encoding:
0
0
0
0
Operation: INC
((Ri)) ← ((Ri)) + 1
25
0509C–8051–07/06
INC
DPTR
Function: Increment Data Pointer
Description: INC DPTR increments the 16-bit data pointer by 1. A 16-bit increment (modulo 216) is performed, and an
overflow of the low-order byte of the data pointer (DPL) from 0FFH to 00H increments the high-order byte (DPH).
No flags are affected.
This is the only 16-bit register which can be incremented.
Example: Registers DPH and DPL contain 12H and 0FEH, respectively. The following instruction sequence,
INC
DPTR
INC
DPTR
INC
DPTR
changes DPH and DPL to 13H and 01H.
Bytes: 1
Cycles: 2
Encoding:
1
0
1
0
0
0
1
1
Operation: INC
(DPTR) ← (DPTR) + 1
JB
blt,rel
Function: Jump if Bit set
Description: If the indicated bit is a one, JB jump to the address indicated; otherwise, it proceeds with the next instruction.
The branch destination is computed by adding the signed relative-displacement in the third instruction byte to the
PC, after incrementing the PC to the first byte of the next instruction. The bit tested is not modified. No flags are
affected.
Example: The data present at input port 1 is 11001010B. The Accumulator holds 56 (01010110B). The following instruction
sequence,
JB
P1.2,LABEL1
JB
ACC. 2,LABEL2
causes program execution to branch to the instruction at label LABEL2.
Bytes: 3
Cycles: 2
Encoding:
0
0
1
0
0
0
0
0
bit address
rel. address
Operation: JB
(PC) ← (PC) + 3
IF (bit) = 1
THEN
(PC) ← (PC) + rel
26
0509C–8051–07/06
JBC
bit,rel
Function: Jump if Bit is set and Clear bit
Description: If the indicated bit is one, JBC branches to the address indicated; otherwise, it proceeds with the next instruction.
The bit will not be cleared if it is already a zero. The branch destination is computed by adding the signed
relative-displacement in the third instruction byte to the PC, after incrementing the PC to the first byte of the next
instruction. No flags are affected.
Note: When this instruction is used to test an output pin, the value used as the original data will be read from the
output data latch, not the input pin.
Example: The Accumulator holds 56H (01010110B). The following instruction sequence,
JBC
ACC.3,LABEL1
JBC
ACC.2,LABEL2
causes program execution to continue at the instruction identified by the label LABEL2, with the Accumulator
modified to 52H (01010010B).
Bytes: 3
Cycles: 2
Encoding:
0
0
0
1
0
0
0
0
bit address
rel. address
Operation: JBC
(PC) ← (PC) + 3
IF (bit) = 1
THEN
(bit) ← 0
(PC) ← (PC) +rel
JC
rel
Function: Jump if Carry is set
Description: If the carry flag is set, JC branches to the address indicated; otherwise, it proceeds with the next instruction. The
branch destination is computed by adding the signed relative-displacement in the second instruction byte to the
PC, after incrementing the PC twice. No flags are affected.
Example: The carry flag is cleared. The following instruction sequence,
JC
LABEL1
CPL
C
JC
LABEL 2
sets the carry and causes program execution to continue at the instruction identified by the label LABEL2.
Bytes: 2
Cycles: 2
Encoding:
0
1
0
0
0
0
0
0
rel. address
Operation: JC
(PC) ← (PC) + 2
IF (C) = 1
THEN
(PC) ← (PC) + rel
27
0509C–8051–07/06
JMP
@A+DPTR
Function: Jump indirect
Description: JMP @A+DPTR adds the eight-bit unsigned contents of the Accumulator with the 16-bit data pointer and loads
the resulting sum to the program counter. This is the address for subsequent instruction fetches. Sixteen-bit
addition is performed (modulo 216): a carry-out from the low-order eight bits propagates through the higher-order
bits. Neither the Accumulator nor the Data Pointer is altered. No flags are affected.
Example: An even number from 0 to 6 is in the Accumulator. The following sequence of instructions branches to one of
four AJMP instructions in a jump table starting at JMP_TBL.
JMP_TBL:
MOV
DPTR, # JMP_TBL
JMP
@A + DPTR
AJMP
LABEL0
AJMP
LABEL1
AJMP
LABEL2
AJMP
LABEL3
If the Accumulator equals 04H when starting this sequence, execution jumps to label LABEL2. Because AJMP is
a 2-byte instruction, the jump instructions start at every other address.
Bytes: 1
Cycles: 2
Encoding:
0
1
1
1
0
0
1
1
Operation: JMP
(PC) ← (A) + (DPTR)
28
0509C–8051–07/06
JNB bit,rel
Function: Jump if Bit Not set
Description: If the indicated bit is a 0, JNB branches to the indicated address; otherwise, it proceeds with the next instruction.
The branch destination is computed by adding the signed relative-displacement in the third instruction byte to the
PC, after incrementing the PC to the first byte of the next instruction. The bit tested is not modified. No flags are
affected.
Example: The data present at input port 1 is 11001010B. The Accumulator holds 56H (01010110B). The following
instruction sequence,
JNB
P1.3,LABEL1
JNB
ACC.3,LABEL2
causes program execution to continue at the instruction at label LABEL2.
Bytes: 3
Cycles: 2
Encoding:
0
0
1
1
0
0
0
0
bit address
rel. address
Operation: JNB
(PC) ← (PC) + 3
IF (bit) = 0
THEN (PC) ← (PC) + rel
JNC
rel
Function: Jump if Carry not set
Description: If the carry flag is a 0, JNC branches to the address indicated; otherwise, it proceeds with the next instruction.
The branch destination is computed by adding the signal relative-displacement in the second instruction byte to
the PC, after incrementing the PC twice to point to the next instruction. The carry flag is not modified.
Example: The carry flag is set. The following instruction sequence,
JNC
LABEL1
CPL
C
JNC
LABEL2
clears the carry and causes program execution to continue at the instruction identified by the label LABEL2.
Bytes: 2
Cycles: 2
Encoding:
0
1
0
1
0
0
0
0
rel. address
Operation: JNC
(PC) ← (PC) + 2
IF (C) = 0
THEN (PC) ← (PC) + rel
29
0509C–8051–07/06
JNZ
rel
Function: Jump if Accumulator Not Zero
Description: If any bit of the Accumulator is a one, JNZ branches to the indicated address; otherwise, it proceeds with the
next instruction. The branch destination is computed by adding the signed relative-displacement in the second
instruction byte to the PC, after incrementing the PC twice. The Accumulator is not modified. No flags are
affected.
Example: The Accumulator originally holds 00H. The following instruction sequence,
JNZ
LABEL1
INC
A
JNZ
LABEL2
sets the Accumulator to 01H and continues at label LABEL2.
Bytes: 2
Cycles: 2
Encoding:
0
1
1
1
0
0
0
0
rel. address
Operation: JNZ
(PC) ← (PC) + 2
IF (A) ≠ 0
THEN (PC) ← (PC) + rel
JZ
rel
Function: Jump if Accumulator Zero
Description: If all bits of the Accumulator are 0, JZ branches to the address indicated; otherwise, it proceeds with the next
instruction. The branch destination is computed by adding the signed relative-displacement in the second
instruction byte to the PC, after incrementing the PC twice. The Accumulator is not modified. No flags are
affected.
Example: The Accumulator originally contains 01H. The following instruction sequence,
JZ
LABEL1
DEC
A
JZ
LABEL2
changes the Accumulator to 00H and causes program execution to continue at the instruction identified by the
label LABEL2.
Bytes: 2
Cycles: 2
Encoding:
0
1
1
0
0
0
0
0
rel. address
Operation: JZ
(PC) ← (PC) + 2
IF (A) = 0
THEN (PC) ← (PC) + rel
30
0509C–8051–07/06
LCALL addr16
Function: Long call
Description: LCALL calls a subroutine located at the indicated address. The instruction adds three to the program counter to
generate the address of the next instruction and then pushes the 16-bit result onto the stack (low byte first),
incrementing the Stack Pointer by two. The high-order and low-order bytes of the PC are then loaded,
respectively, with the second and third bytes of the LCALL instruction. Program execution continues with the
instruction at this address. The subroutine may therefore begin anywhere in the full 64K byte program memory
address space. No flags are affected.
Example: Initially the Stack Pointer equals 07H. The label SUBRTN is assigned to program memory location 1234H. After
executing the instruction,
LCALL
SUBRTN
at location 0123H, the Stack Pointer will contain 09H, internal RAM locations 08H and 09H will contain 26H and
01H, and the PC will contain 1234H.
Bytes: 3
Cycles: 2
Encoding:
0
0
0
1
0
0
1
0
addr15-addr8
addr7-addr0
Operation: LCALL
(PC) ← (PC) + 3
(SP) ← (SP) + 1
((SP)) ← (PC7-0)
(SP) ← (SP) + 1
((SP)) ← (PC15-8)
(PC) ← addr 15-0
LJMP
addr16
Function: Long Jump
Description: LJMP causes an unconditional branch to the indicated address, by loading the high-order and low-order bytes of
the PC (respectively) with the second and third instruction bytes. The destination may therefore be anywhere in
the full 64K program memory address space. No flags are affected.
Example: The label JMPADR is assigned to the instruction at program memory location 1234H. The instruction,
LJMP
JMPADR
at location 0123H will load the program counter with 1234H.
Bytes: 3
Cycles: 2
Encoding:
0
0
0
0
0
0
1
0
addr15-addr8
addr7-addr0
Operation: LJMP
(PC) ← addr 15-0
31
0509C–8051–07/06
MOV
<dest-byte>,<src-byte>
Function: Move byte variable
Description: The byte variable indicated by the second operand is copied into the location specified by the first operand. The
source byte is not affected. No other register or flag is affected.
This is by far the most flexible operation. Fifteen combinations of source and destination addressing modes are
allowed.
Example: Internal RAM location 30H holds 40H. The value of RAM location 40H is 10H. The data present at input port 1 is
11001010B (0CAH).
MOV
R0,#30H
;R0 < = 30H
MOV
A,@R0
;A < = 40H
MOV
R1,A
;R1 < = 40H
MOV
B,@R1
;B < = 10H
MOV
@R1,P1
;RAM (40H) < = 0CAH
MOV
P2,P1
;P2 #0CAH
leaves the value 30H in register 0, 40H in both the Accumulator and register 1, 10H in register B, and 0CAH
(11001010B) both in RAM location 40H and output on port 2.
MOV
A,R n
Bytes: 1
Cycles: 1
Encoding:
1
1
1
0
1
r
r
r
1
0
0
1
0
1
0
1
1
i
Operation: MOV
(A) ← (R n)
*MOV A,direct
Bytes: 2
Cycles: 1
Encoding:
1
1
direct address
Operation: MOV
(A) ← (direct)
* MOV A,ACC is not a valid Instruction.
MOV
A,@R i
Bytes: 1
Cycles: 1
Encoding:
1
1
1
0
Operation: MOV
(A) ← ((R i))
32
0509C–8051–07/06
MOV
A,#data
Bytes: 2
Cycles: 1
Encoding:
0
1
1
1
0
1
0
0
immediate data
1
1
1
r
r
r
1
0
1
r
r
r
direct addr.
1
1
1
r
r
r
immediate data
1
1
0
1
0
1
direct address
0
0
1
r
r
r
direct address
Operation: MOV
(A) ← #data
MOV
R n,A
Bytes: 1
Cycles: 1
Encoding:
1
1
Operation: MOV
(Rn) ← (A)
MOV
R n,direct
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: MOV
(Rn) ← (direct)
MOV
R n,#data
Bytes: 2
Cycles: 1
Encoding:
0
1
Operation: MOV
(Rn) ← #data
MOV
direct,A
Bytes: 2
Cycles: 1
Encoding:
1
1
Operation: MOV
(direct) ← (A)
MOV
direct,R n
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: MOV
(direct) ← (Rn)
33
0509C–8051–07/06
MOV
direct,direct
Bytes: 3
Cycles: 2
Encoding:
1
0
0
0
0
1
0
1
dir. addr. (dest)
0
0
1
1
i
direct addr.
1
0
1
0
1
direct address
1
1
0
1
1
i
1
0
0
1
1
i
direct addr.
1
0
1
1
i
immediate data
dir. addr. (scr)
Operation: MOV
(direct) ← (direct)
MOV
direct,@R i
Bytes: 2
Cycles: 2
Encoding:
1
0
0
Operation: MOV
(direct) ← ((Ri))
MOV
direct,#data
Bytes: 3
Cycles: 2
Encoding:
0
1
1
immediate data
Operation: MOV
(direct) ← #data
MOV
@R i,A
Bytes: 1
Cycles: 1
Encoding:
1
1
Operation: MOV
((Ri)) ← (A)
MOV
@R i,direct
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: MOV
((Ri)) ← (direct)
MOV
@R i,#data
Bytes: 2
Cycles: 1
Encoding:
0
1
1
Operation: MOV
((Ri)) ← #data
34
0509C–8051–07/06
MOV
<dest-bit>,<src-bit>
Function: Move bit data
Description: MOV <dest-bit>,<src-bit> copies the Boolean variable indicated by the second operand into the location
specified by the first operand. One of the operands must be the carry flag; the other may be any directly
addressable bit. No other register or flag is affected.
Example: The carry flag is originally set. The data present at input Port 3 is 11000101B. The data previously written to
output Port 1 is 35H (00110101B).
MOV
P1.3,C
MOV
C,P3.3
MOV
P1.2,C
leaves the carry cleared and changes Port 1 to 39H (00111001B).
MOV
C,bit
Bytes: 2
Cycles: 1
Encoding:
1
0
1
0
0
0
1
0
bit address
0
1
0
0
1
0
bit address
Operation: MOV
(C) ← (bit)
MOV
bit,C
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: MOV
(bit) ← (C)
MOV
DPTR,#data16
Function: Load Data Pointer with a 16-bit constant
Description: MOV DPTR,#data16 loads the Data Pointer with the 16-bit constant indicated. The 16-bit constant is loaded into
the second and third bytes of the instruction. The second byte (DPH) is the high-order byte, while the third byte
(DPL) holds the lower-order byte. No flags are affected.
This is the only instruction which moves 16 bits of data at once.
Example: The instruction,
MOV
DPTR, # 1234H
loads the value 1234H into the Data Pointer: DPH holds 12H, and DPL holds 34H.
Bytes: 3
Cycles: 2
Encoding:
1
0
0
1
0
0
0
0
immed. data15-8
immed. data7-0
Operation: MOV
(DPTR) ← #data15-0
DPH ← DPL ← #data15-8 ← #data7-0
35
0509C–8051–07/06
MOVC A,@A+ <base-reg>
Function: Move Code byte
Description: The MOVC instructions load the Accumulator with a code byte or constant from program memory. The address
of the byte fetched is the sum of the original unsigned 8-bit Accumulator contents and the contents of a 16-bit
base register, which may be either the Data Pointer or the PC. In the latter case, the PC is incremented to the
address of the following instruction before being added with the Accumulator; otherwise the base register is not
altered. Sixteen-bit addition is performed so a carry-out from the low-order eight bits may propagate through
higher-order bits. No flags are affected.
Example: A value between 0 and 3 is in the Accumulator. The following instructions will translate the value in the
Accumulator to one of four values defined by the DB (define byte) directive.
REL_PC:
INC
A
MOVC
A,@A+PC
RET
DB
66H
DB
77H
DB
88H
DB
99H
If the subroutine is called with the Accumulator equal to 01H, it returns with 77H in the Accumulator. The INC A
before the MOVC instruction is needed to “get around” the RET instruction above the table. If several bytes of
code separate the MOVC from the table, the corresponding number is added to the Accumulator instead.
MOVC A,@A+DPTR
Bytes: 1
Cycles: 2
Encoding:
1
0
0
1
0
0
1
1
0
0
1
1
Operation: MOVC
(A) ← ((A) + (DPTR))
MOVC A,@A+PC
Bytes: 1
Cycles: 2
Encoding:
1
0
0
0
Operation: MOVC
(PC) ← (PC) + 1
(A) ← ((A) + (PC))
36
0509C–8051–07/06
MOVX <dest-byte>,<src-byte>
Function: Move External
Description: The MOVX instructions transfer data between the Accumulator and a byte of external data memory, which is why
“X” is appended to MOV. There are two types of instructions, differing in whether they provide an 8-bit or 16-bit
indirect address to the external data RAM.
In the first type, the contents of R0 or R1 in the current register bank provide an 8-bit address multiplexed with
data on P0. Eight bits are sufficient for external I/O expansion decoding or for a relatively small RAM array. For
somewhat larger arrays, any output port pins can be used to output higher-order address bits. These pins are
controlled by an output instruction preceding the MOVX.
In the second type of MOVX instruction, the Data Pointer generates a 16-bit address. P2 outputs the high-order
eight address bits (the contents of DPH), while P0 multiplexes the low-order eight bits (DPL) with data. The P2
Special Function Register retains its previous contents, while the P2 output buffers emit the contents of DPH.
This form of MOVX is faster and more efficient when accessing very large data arrays (up to 64K bytes), since
no additional instructions are needed to set up the output ports.
It is possible to use both MOVX types in some situations. A large RAM array with its high-order address lines
driven by P2 can be addressed via the Data Pointer, or with code to output high-order address bits to P2,
followed by a MOVX instruction using R0 or R1.
Example: An external 256 byte RAM using multiplexed address/data lines is connected to the 8051 Port 0. Port 3 provides
control lines for the external RAM. Ports 1 and 2 are used for normal I/O. Registers 0 and 1 contain 12H and
34H. Location 34H of the external RAM holds the value 56H. The instruction sequence,
MOVX
A,@R1
MOVX
@R0,A
copies the value 56H into both the Accumulator and external RAM location 12H.
MOVX A,@Ri
Bytes: 1
Cycles: 2
Encoding:
1
1
1
0
0
0
1
i
1
0
0
0
0
0
Operation: MOVX
(A) ← ((R i))
MOVX A,@DPTR
Bytes: 1
Cycles: 2
Encoding:
1
1
Operation: MOVX
(A) ← ((DPTR))
37
0509C–8051–07/06
MOVX @R i,A
Bytes: 1
Cycles: 2
Encoding:
1
1
1
1
0
0
1
i
1
1
0
0
0
0
Operation: MOVX
((Ri)) ← (A)
MOVX @DPTR,A
Bytes: 1
Cycles: 2
Encoding:
1
1
Operation: MOVX
(DPTR) ← (A)
MUL
AB
Function: Multiply
Description: MUL AB multiplies the unsigned 8-bit integers in the Accumulator and register B. The low-order byte of the 16-bit
product is left in the Accumulator, and the high-order byte in B. If the product is greater than 255 (0FFH), the
overflow flag is set; otherwise it is cleared. The carry flag is always cleared.
Example: Originally the Accumulator holds the value 80 (50H). Register B holds the value 160 (0A0H). The instruction,
MUL
AB
will give the product 12,800 (3200H), so B is changed to 32H (00110010B) and the Accumulator is cleared. The
overflow flag is set, carry is cleared.
Bytes: 1
Cycles: 4
Encoding:
1
0
1
0
0
1
0
0
Operation: MUL
(A)7-0 ← (A) X (B)
(B)15-8
38
0509C–8051–07/06
NOP
Function: No Operation
Description: Execution continues at the following instruction. Other than the PC, no registers or flags are affected.
Example: A low-going output pulse on bit 7 of Port 2 must last exactly 5 cycles. A simple SETB/CLR sequence generates
a one-cycle pulse, so four additional cycles must be inserted. This may be done (assuming no interrupts are
enabled) with the following instruction sequence,
CLR
P2.7
NOP
NOP
NOP
NOP
SETB
P2.7
Bytes: 1
Cycles: 1
Encoding:
0
0
0
0
0
0
0
0
Operation: NOP
(PC) ← (PC) + 1
ORL
<dest-byte> <src-byte>
Function: Logical-OR for byte variables
Description: ORL performs the bitwise logical-OR operation between the indicated variables, storing the results in the
destination byte. No flags are affected.
The two operands allow six addressing mode combinations. When the destination is the Accumulator, the source
can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the
source can be the Accumulator or immediate data.
Note: When this instruction is used to modify an output port, the value used as the original port data is read from
the output data latch, not the input pins.
Example: If the Accumulator holds 0C3H (11000011B) and R0 holds 55H (01010101B) then the following instruction,
ORL
A,R0
leaves the Accumulator holding the value 0D7H (1101011lB).When the destination is a directly addressed byte,
the instruction can set combinations of bits in any RAM location or hardware register. The pattern of bits to be set
is determined by a mask byte, which may be either a constant data value in the instruction or a variable
computed in the Accumulator at run-time. The instruction,
ORL
P1,#00110010B
sets bits 5, 4, and 1 of output Port 1.
ORL A,Rn
Bytes: 1
Cycles: 1
Encoding:
0
1
Operation: ORL
(A) ← (A)
0
0
1
r
r
r
∨ (Rn)
39
0509C–8051–07/06
ORL
A,direct
Bytes: 2
Cycles: 1
Encoding:
0
1
Operation: ORL
(A) ← (A)
ORL
0
0
0
1
0
1
direct address
0
0
1
1
i
0
0
1
0
0
immediate data
0
0
0
1
0
direct address
0
0
1
1
direct addr.
∨ (direct)
A,@R i
Bytes: 1
Cycles: 1
Encoding:
0
1
Operation: ORL
(A) ← (A)
ORL
0
∨((Ri))
A,#data
Bytes: 2
Cycles: 1
Encoding:
0
1
Operation: ORL
(A) ← (A)
ORL
0
∨ #data
direct,A
Bytes: 2
Cycles: 1
Encoding:
0
1
0
Operation: ORL
(direct) ← (direct)
ORL
∨ (A)
direct,#data
Bytes: 3
Cycles: 2
Encoding:
0
1
0
Operation: ORL
(direct) ← (direct)
0
immediate data
∨ #data
40
0509C–8051–07/06
ORL
C,<src-bit>
Function: Logical-OR for bit variables
Description: Set the carry flag if the Boolean value is a logical 1; leave the carry in its current state otherwise. A slash ( / )
preceding the operand in the assembly language indicates that the logical complement of the addressed bit is
used as the source value, but the source bit itself is not affected. No other flags are affected.
Example: Set the carry flag if and only if P1.0 = 1, ACC. 7 = 1, or OV = 0:
ORL
MOV
C,P1.0
;LOAD CARRY WITH INPUT PIN P10
ORL
C,ACC.7
;OR CARRY WITH THE ACC. BIT 7
ORL
C,/OV
;OR CARRY WITH THE INVERSE OF OV.
C,bit
Bytes: 2
Cycles: 2
Encoding:
0
1
Operation: ORL
(C) ← (C)
ORL
1
1
0
0
1
0
bit address
0
0
0
0
0
bit address
∨ (bit)
C,/bit
Bytes: 2
Cycles: 2
Encoding:
1
0
Operation: ORL
(C) ← (C)
POP
1
∨ (bit)
direct
Function: Pop from stack.
Description: The contents of the internal RAM location addressed by the Stack Pointer is read, and the Stack Pointer is
decremented by one. The value read is then transferred to the directly addressed byte indicated. No flags are
affected.
Example: The Stack Pointer originally contains the value 32H, and internal RAM locations 30H through 32H contain the
values 20H, 23H, and 01H, respectively. The following instruction sequence,
POP
DPH
POP
DPL
leaves the Stack Pointer equal to the value 30H and sets the Data Pointer to 0123H. At this point, the following
instruction,
POP
SP
leaves the Stack Pointer set to 20H. In this special case, the Stack Pointer was decremented to 2FH before
being loaded with the value popped (20H).
Bytes: 2
Cycles: 2
Encoding:
1
1
0
1
0
0
0
0
direct address
Operation: POP
(direct) ← ((SP))
(SP) ← (SP) - 1
41
0509C–8051–07/06
PUSH direct
Function: Push onto stack
Description: The Stack Pointer is incremented by one. The contents of the indicated variable is then copied into the internal
RAM location addressed by the Stack Pointer. Otherwise no flags are affected.
Example: On entering an interrupt routine, the Stack Pointer contains 09H. The Data Pointer holds the value 0123H. The
following instruction sequence,
PUSH
DPL
PUSH
DPH
leaves the Stack Pointer set to 0BH and stores 23H and 01H in internal RAM locations 0AH and 0BH,
respectively.
Bytes: 2
Cycles: 2
Encoding:
1
1
0
0
0
0
0
0
direct address
Operation: PUSH
(SP) ← (SP) + 1
((SP)) ← (direct)
RET
Function: Return from subroutine
Description: RET pops the high- and low-order bytes of the PC successively from the stack, decrementing the Stack Pointer
by two. Program execution continues at the resulting address, generally the instruction immediately following an
ACALL or LCALL. No flags are affected.
Example: The Stack Pointer originally contains the value 0BH. Internal RAM locations 0AH and 0BH contain the values
23H and 01H, respectively. The following instruction,
RET
leaves the Stack Pointer equal to the value 09H. Program execution continues at location 0123H.
Bytes: 1
Cycles: 2
Encoding:
0
0
1
0
0
0
1
0
Operation: RET
(PC15-8) ← ((SP))
(SP) ← (SP) - 1
(PC7-0 ) ← ((SP))
(SP) ← (SP) - 1
42
0509C–8051–07/06
RETI
Function: Return from interrupt
Description: RETI pops the high- and low-order bytes of the PC successively from the stack and restores the interrupt logic to
accept additional interrupts at the same priority level as the one just processed. The Stack Pointer is left
decremented by two. No other registers are affected; the PSW is not automatically restored to its pre-interrupt
status. Program execution continues at the resulting address, which is generally the instruction immediately after
the point at which the interrupt request was detected. If a lower- or same-level interrupt was pending when the
RETI instruction is executed, that one instruction is executed before the pending interrupt is processed.
Example: The Stack Pointer originally contains the value 0BH. An interrupt was detected during the instruction ending at
location 0122H. Internal RAM locations 0AH and 0BH contain the values 23H and 01H, respectively. The
following instruction,
RETI
leaves the Stack Pointer equal to 09H and returns program execution to location 0123H.
Bytes: 1
Cycles: 2
Encoding:
0
0
1
1
0
0
1
0
Operation: RETI
(PC15-8) ← ((SP))
(SP) ← (SP) - 1
(PC7-0 ) ← ((SP))
(SP) ← (SP) - 1
RL
A
Function: Rotate Accumulator Left
Description: The eight bits in the Accumulator are rotated one bit to the left. Bit 7 is rotated into the bit 0 position. No flags are
affected.
Example: The Accumulator holds the value 0C5H (11000101B). The following instruction,
RL
A
leaves the Accumulator holding the value 8BH (10001011B) with the carry unaffected.
Bytes: 1
Cycles: 1
Encoding:
0
0
1
0
0
0
1
1
Operation: RL
(An + 1) ← (An) n = 0 - 6
(A0) ← (A7)
43
0509C–8051–07/06
RLC
A
Function: Rotate Accumulator Left through the Carry flag
Description: The eight bits in the Accumulator and the carry flag are together rotated one bit to the left. Bit 7 moves into the
carry flag; the original state of the carry flag moves into the bit 0 position. No other flags are affected.
Example: The Accumulator holds the value 0C5H(11000101B), and the carry is zero. The following instruction,
RLC
A
leaves the Accumulator holding the value 8BH (10001010B) with the carry set.
Bytes: 1
Cycles: 1
Encoding:
0
0
1
1
0
0
1
1
Operation: RLC
(An + 1) ← (An) n = 0 - 6
(A0) ← (C)
(C) ← (A7)
RR
A
Function: Rotate Accumulator Right
Description: The eight bits in the Accumulator are rotated one bit to the right. Bit 0 is rotated into the bit 7 position. No flags
are affected.
Example: The Accumulator holds the value 0C5H (11000101B). The following instruction,
RR
A
leaves the Accumulator holding the value 0E2H (11100010B) with the carry unaffected.
Bytes: 1
Cycles: 1
Encoding:
0
0
0
0
0
0
1
1
Operation: RR
(An) ← (An + 1) n = 0 - 6
(A7) ← (A0)
RRC
A
Function: Rotate Accumulator Right through Carry flag
Description: The eight bits in the Accumulator and the carry flag are together rotated one bit to the right. Bit 0 moves into the
carry flag; the original value of the carry flag moves into the bit 7 position. No other flags are affected.
Example: The Accumulator holds the value 0C5H (11000101B), the carry is zero. The following instruction,
RRC
A
leaves the Accumulator holding the value 62 (01100010B) with the carry set.
Bytes: 1
Cycles: 1
Encoding:
0
0
0
1
0
0
1
1
Operation: RRC
(An) ← (An + 1) n = 0 - 6
(A7) ← (C)
(C) ← (A0)
44
0509C–8051–07/06
SETB
<bit>
Function: Set Bit
Description: SETB sets the indicated bit to one. SETB can operate on the carry flag or any directly addressable bit. No other
flags are affected.
Example: The carry flag is cleared. Output Port 1 has been written with the value 34H (00110100B). The following
instructions,
SETB
C
SETB
P1.0
sets the carry flag to 1 and changes the data output on Port 1 to 35H (00110101B).
SETB C
Bytes: 1
Cycles: 1
Encoding:
1
1
0
1
0
0
1
1
1
0
1
0
0
1
0
Operation: SETB
(C) ← 1
SETB bit
Bytes: 2
Cycles: 1
Encoding:
1
bit address
Operation: SETB
(bit) ← 1
SJMP
rel
Function: Short Jump
Description: Program control branches unconditionally to the address indicated. The branch destination is computed by
adding the signed displacement in the second instruction byte to the PC, after incrementing the PC twice.
Therefore, the range of destinations allowed is from 128 bytes preceding this instruction 127 bytes following it.
Example: The label RELADR is assigned to an instruction at program memory location 0123H. The following instruction,
SJMP
RELADR
assembles into location 0100H. After the instruction is executed, the PC contains the value 0123H.
Note: Under the above conditions the instruction following SJMP is at 102H. Therefore, the displacement byte of
the instruction is the relative offset (0123H-0102H) = 21H. Put another way, an SJMP with a displacement of
0FEH is a one-instruction infinite loop.
Bytes: 2
Cycles: 2
Encoding:
1
0
0
0
0
0
0
0
rel. address
Operation: SJMP
(PC) ← (PC) + 2
(PC) ← (PC) + rel
45
0509C–8051–07/06
SUBB A,<src-byte>
Function: Subtract with borrow
Description: SUBB subtracts the indicated variable and the carry flag together from the Accumulator, leaving the result in the
Accumulator. SUBB sets the carry (borrow) flag if a borrow is needed for bit 7 and clears C otherwise. (If C was
set before executing a SUBB instruction, this indicates that a borrow was needed for the previous step in a
multiple-precision subtraction, so the carry is subtracted from the Accumulator along with the source operand.)
AC is set if a borrow is needed for bit 3 and cleared otherwise. OV is set if a borrow is needed into bit 6, but not
into bit 7, or into bit 7, but not bit 6.
When subtracting signed integers, OV indicates a negative number produced when a negative value is
subtracted from a positive value, or a positive result when a positive number is subtracted from a negative
number.
The source operand allows four addressing modes: register, direct, register-indirect, or immediate.
Example: The Accumulator holds 0C9H (11001001B), register 2 holds 54H (01010100B), and the carry flag is set. The
instruction,
SUBB
A,R2
will leave the value 74H (01110100B) in the accumulator, with the carry flag and AC cleared but OV set.
Notice that 0C9H minus 54H is 75H. The difference between this and the above result is due to the carry
(borrow) flag being set before the operation. If the state of the carry is not known before starting a single or
multiple-precision subtraction, it should be explicitly cleared by CLR C instruction.
SUBB A,R n
Bytes: 1
Cycles: 1
Encoding:
1
0
0
1
1
r
r
r
0
1
0
1
0
1
1
i
0
1
0
0
Operation: SUBB
(A) ← (A) - (C) - (R n)
SUBB A,direct
Bytes: 2
Cycles: 1
Encoding:
1
0
0
1
direct address
Operation: SUBB
(A) ← (A) - (C) - (direct)
SUBB A,@R i
Bytes: 1
Cycles: 1
Encoding:
1
0
0
1
Operation: SUBB
(A) ← (A) - (C) - ((R i))
SUBB A,#data
Bytes: 2
Cycles: 1
Encoding:
1
0
0
1
immediate data
Operation: SUBB
(A) ← (A) - (C) - #data
46
0509C–8051–07/06
SWAP A
Function: Swap nibbles within the Accumulator
Description: SWAP A interchanges the low- and high-order nibbles (four-bit fields) of the Accumulator (bits 3 through 0 and
bits 7 through 4). The operation can also be thought of as a 4-bit rotate instruction. No flags are affected.
Example: The Accumulator holds the value 0C5H (11000101B). The instruction,
SWAP
A
leaves the Accumulator holding the value 5CH (01011100B).
Bytes: 1
Cycles: 1
Encoding:
1
1
0
0
0
1
0
0
Operation: SWAP
(A3-0 ) D (A7-4 )
XCH
A,<byte>
Function: Exchange Accumulator with byte variable
Description: XCH loads the Accumulator with the contents of the indicated variable, at the same time writing the original
Accumulator contents to the indicated variable. The source/destination operand can use register, direct, or
register-indirect addressing.
Example: R0 contains the address 20H. The Accumulator holds the value 3FH (0011111lB). Internal RAM location 20H
holds the value 75H (01110101B). The following instruction,
XCH
A,@R0
leaves RAM location 20H holding the values 3FH (00111111B) and 75H (01110101B) in the accumulator.
XCH
A,R n
Bytes: 1
Cycles: 1
Encoding:
1
1
0
0
1
r
r
r
0
0
0
1
0
1
0
0
0
1
1
i
Operation: XCH
(A) D ((R n)
XCH
A,direct
Bytes: 2
Cycles: 1
Encoding:
1
1
direct address
Operation: XCH
(A) D (direct)
XCH
A,@R i
Bytes: 1
Cycles: 1
Encoding:
1
1
Operation: XCH
(A) D ((R i))
47
0509C–8051–07/06
XCHD A,@Ri
Function: Exchange Digit
Description: XCHD exchanges the low-order nibble of the Accumulator (bits 3 through 0), generally representing a
hexadecimal or BCD digit, with that of the internal RAM location indirectly addressed by the specified register.
The high-order nibbles (bits 7-4) of each register are not affected. No flags are affected.
Example: R0 contains the address 20H. The Accumulator holds the value 36H (00110110B). Internal RAM location 20H
holds the value 75H (01110101B). The following instruction,
XCHD
A,@R0
leaves RAM location 20H holding the value 76H (01110110B) and 35H (00110101B) in the Accumulator.
Bytes: 1
Cycles: 1
Encoding:
1
1
0
1
0
1
1
i
Operation: XCHD
(A3-0 ) D ((Ri3-0))
XRL
<dest-byte>,<src-byte>
Function: Logical Exclusive-OR for byte variables
Description: XRL performs the bitwise logical Exclusive-OR operation between the indicated variables, storing the results in
the destination. No flags are affected.
The two operands allow six addressing mode combinations. When the destination is the Accumulator, the source
can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the
source can be the Accumulator or immediate data.
Note: When this instruction is used to modify an output port, the value used as the original port data is read from
the output data latch, not the input pins.
Example: If the Accumulator holds 0C3H (1100001lB) and register 0 holds 0AAH (10101010B) then the instruction,
XRL
A,R0
leaves the Accumulator holding the value 69H (01101001B).
When the destination is a directly addressed byte, this instruction can complement combinations of bits in any
RAM location or hardware register. The pattern of bits to be complemented is then determined by a mask byte,
either a constant contained in the instruction or a variable computed in the Accumulator at run-time. The
following instruction,
XRL
P1,#00110001B
complements bits 5, 4, and 0 of output Port 1.
XRL
A,R n
Bytes: 1
Cycles: 1
Encoding:
0
1
1
0
1
r
r
r
Operation: XRL
(A) ← (A) V (Rn)
48
0509C–8051–07/06
Document Revision History
Changes from 0509B - 08/05 to 0509C - 07/06
1.
Correcto to MOV Direct, page 49.
49
0509C–8051–07/06
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically providedotherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© Atmel Corporation 2006. All rights reserved. Atmel ®, logo and combinations thereof, and Everywhere You Are ® are the trademarks or registered trademarks, of Atmel Corporation or its subsidiaries. Copied by permission of Intel Corporation. Copyright Intel Corporation 1994. Other terms
and product names may be trademarks of others.
Printed on recycled paper.
0509C–8051–07/06