MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS HSON−6 CASE 506AE−01 ISSUE A 6 1 DATE 26 JAN 2005 SCALE 2:1 A D PIN ONE REFERENCE 6 B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.15 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 4 E1 2X E 0.20 C 1 2X 3 0.20 C TOP VIEW DIM A A3 b D D2 E E1 E2 e L 0.10 C A 6X 0.08 C SEATING PLANE (A3) C SIDE VIEW MILLIMETERS MIN MAX 0.70 0.90 0.15 REF 0.20 0.40 2.90 BSC 1.40 1.60 3.00 BSC 2.80 BSC 1.50 1.70 0.95 BSC 0.15 0.25 D2 1 L GENERIC MARKING DIAGRAM* e 3 6X 6 E2 EXPOSED PAD 6 XXX XYY 4 b BOTTOM VIEW 6X NOTE 3 1 0.10 C A B 0.05 C XXXX YY = Specific Device Code = Wafer Lot *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ ”, may or may not be present. DOCUMENT NUMBER: STATUS: 98AON19447D ON SEMICONDUCTOR STANDARD NEW STANDARD: Semiconductor Components Industries, LLC, 2002 October, DESCRIPTION: 2002 − Rev. 0 http://onsemi.com HSON−6, 2.9 X 3.0 MM, 0.95 MM 1 PITCH Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. Case Outline Number: PAGE 1 OFXXX 2 DOCUMENT NUMBER: 98AON19447D PAGE 2 OF 2 ISSUE REVISION DATE O RELEASED FOR PRODUCTION. REQ. BY B. LOFTS 13 AUG 2004 A ADDED “EXPOSED PAD” NOTE ON BOTTOM VIEW. REQ. BY K. VALDEZ. 26 JAN 2005 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Semiconductor Components Industries, LLC, 2005 January, 2005 − Rev. 01A Case Outline Number: 506AE