Future Technology Devices International Ltd. V2DIP1-64 VNCL2-64Q Development Module Datasheet Document Reference No.: FT_000165 Version 1.01 Issue Date: 2010-05-25 Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 E-Mail (Support): [email protected] Web: http://www.vinculum.com Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar y information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 1 Introduction V2DIP1-64 module is designed to allow rapid development of designs using the VNC2-64Q IC. The V2DIP1-64 is supplied as a PCB designed to fit into a 60 pin 0.8” wide 0.1” pitch DIP socket.The module provides access to the UART, parallel FIFO, and SPI interface pins of the VNC2-64Q device, via its IO bus pins. One USB port is accessed via a type A USB connector. Figure 1.1 - V2DIP1 64 The VNC2 is the second of FTDI’s Vinculum family of Embedded dual USB host controller devices. The VNC2 device provides USB Host interfacing capability for a variety of different USB device classes including support for BOMS (bulk only mass storage), Printer, HID (human interface devices). For mass storage devices such as USB Flash drives, VNC2 also transparently handles the FAT file structure. Communication with non USB devices such as a low cost microcontroller is accomplished via either UART, SPI or parallel FIFO interfaces. The VNC2 provides a new cost effective solution for providing USB Host capability into products that previously did not have the hardware resources available. The VNC2 supports the capability to enable customers to develop custom firmware using the Vinculum II development software tool suite. The development tools support compiler, linker and debugger tools complete within an integrated development environment (IDE). The Vinculum-II VNC2 family of devices are available in Pb-free (RoHS compliant) 32-lead LQFP, 32-lead QFN, 48-lead LQFP, 48-lead QFN, 64-Lead lQFP and 64-lead QFN packages Copyright © 2010 Future Technology Devices International Limited 1 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Table of Contents 1 Introduction .................................................................... 1 2 Features .......................................................................... 3 3 Pin Out and Signal Description ........................................ 4 3.1 Module Pin Out.......................................................................... 4 3.2 Pin Signal Description ............................................................... 6 3.3 Default Interface I/O Pin Configuration.................................... 8 3.4 UART Interface ....................................................................... 10 3.4.1 3.5 Serial Peripheral Interface (SPI) ............................................ 11 3.5.1 Signal Description - SPI Slave ................................................................... 11 3.5.2 Signal Description - SPI Master ................................................................. 12 3.6 Parallel FIFO Interface - Asynchronous Mode ......................... 13 3.6.1 Signal Description - Parallel FIFO Interface ................................................. 13 3.6.2 Timing Diagram – Asynchronous FIFO Mode Read and Write Cycle................ 14 3.7 Parallel FIFO Interface-Synchronous Mode ............................. 15 3.7.1 3.8 5 Timing Diagram – Synchronous FIFO Mode Read and Write Cycle ................. 15 Debugger Interface ................................................................. 17 3.8.1 4 Signal Description – UART Interface ........................................................... 10 ignal Description - Debugger Interface ....................................................... 17 Firmware....................................................................... 18 4.1 Firmware Support ................................................................... 18 4.2 Available Firmware ................................................................. 18 4.3 Firmware Upgrades ................................................................. 18 External circuit Configuration ....................................... 19 5.1 Adding a second USB Port ....................................................... 19 6 Mechanical Dimensions ................................................. 20 7 Schematic Diagram ....................................................... 21 8 Contact Information ...................................................... 22 Appendix A – References ................................................................. 23 Appendix B – List of Figures and Tables .......................................... 24 List of Figures ................................................................................. 24 List of Tables ................................................................................... 24 Appendix C – Revision History ......................................................... 25 Copyright © 2010 Future Technology Devices International Limited 2 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 2 Features The V2DIP1-64 incorporates the following features: Uses FTDI’s VNC2-64Q embedded USB host controller IC device All VNC2 signals available on 0.8” wide, 0.1” pitch DIL male connectors. USB single ‘A’ type USB to interface with USB peripheral devices. Power and traffic indicator LED’s Second USB interface port available via module header pins if required. UART, parallel FIFO and SPI interfaces can be programmed to a choice of available I/O pins Single 5V supply input from DIL connectors or 5V supplied via USB VBUS slave interface or debugger module. Auxiliary 3.3 V / 200 mA power output to external logic V2DIP1-64 is a Pb-free, RoHS complaint development module Debugger interface pin available on DIL pins or via 6 way male header which interfaces to separate debugger module. Firmware upgrades via UART or debugger interface. FOC software development suite of tools to create customised firmware includes a Compiler, Linker,Debugger and Assembler all wrapped up in an easy to use Integrated Design Environment GUI. Copyright © 2010 Future Technology Devices International Limited 3 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3 Pin Out and Signal Description 3.1 Module Pin Out Figure 3.1 - V2DIP1-64 Module Pin Out (Top View) Copyright © 2010 Future Technology Devices International Limited 4 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Figure 3.2 - V2DIP1-64 Module Pin Out (Bottom View) Copyright © 2010 Future Technology Devices International Limited 5 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.2 Pin Signal Description Pin No. J1-1 J1-2 J1-3 J1-4 J1-5 J1-6 J1-7 J1-8 J1-9 J1-10 VNC2 Signal Name IOBUS26 IOBUS27 IOBUS28 IOBUS29 IOBUS30 IOBUS31 IOBUS32 IOBUS33 IOBUS34 GND Pin Name on PCB Type IO26 IO27 IO28 IO29 IO30 IO31 IO32 IO33 IO34 GND I/O I/O I/O I/O I/O I/O I/O I/O I/O PWR Description 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / Module ground supply pin control control control control control control control control control bus bus bus bus bus bus bus bus bus bit bit bit bit bit bit bit bit bit 26 27 28 29 30 31 32 33 34 J1-11 J1-12 5V0 5V0 PWR Input Not connected 5.0V module supply pin. This pin can be used to provide the 5.0V input to the V2DIP1-64 when the V2DIP1-64 is not powered from the USB connector (VBUS) or the debugger interface. Also connected to DIL connector pins J1-12, J1-13 and J1-19 and J3-6. J1-13 5V0 5V0 PWR Input 5.0V module supply pin. This pin can be used to provide the 5.0V input to the V2DIP1-64 when the V2DIP1-64 is not powered from the USB connector (VBUS) or the debugger interface. Also connected to DIL connector pins J1-12, J1-13 and J1-19 and J3-6. J1-14 J1-15 J1-16 J1-17 J1-18 J1-19 IOBUS5 IOBUS6 IOBUS7 IOBUS8 IOBUS9 5V0 IO5 IO6 IO7 IO8 IO9 5V0 I/O I/O I/O I/O I/O PWR Input 5V safe bidirectional data / control bus bit 5 5V safe bidirectional data / control bus bit 6 5V safe bidirectional data / control bus bit 7 5V safe bidirectional data / control bus bit 8 5V safe bidirectional data / control bus bit 9 5.0V module supply pin. This pin can be used to provide the 5.0V input to the V2DIP1-64 when the V2DIP1-64 is not powered from the USB connector (VBUS) or the debugger interface. Also connected to DIL connector pins J1-12, J1-13 and J1-19 and J3-6. J1-20 J1-21 J1-22 IOBUS10 IOBUS11 IO10 IO11 I/O I/O USBD1P U1P I/O USBD1M U1M I/O J1-24 J1-25 J1-26 J1-27 J1-28 J1-29 IOBUS12 GND IOBUS13 IOBUS14 IOBUS15 IOBUS16 IO12 GND IO13 IO14 IO15 IO16 I/O PWR I/O I/O I/O I/O J1-30 IOBUS17 IO17 J1-23 J2-1 J2-2 J2-3 J2-4 J2-5 J2-6 J2-7 Table 3.1 - IOBUS43 IO43 IOBUS42 IO42 IOBUS41 IO41 IOBUS40 IO40 IOBUS39 IO39 IOBUS38 IO38 IOBUS37 IO37 Pin Signal Descriptions 5V safe bidirectional data / control bus bit 10 5V safe bidirectional data / control bus bit 11 USB host / slave port 1 - USBData Signal Plus with integrated pull up / pull down resistor. Module has on board 27 Ω USB series resistor. This pin can be brought out along with pin J1-23 to provide a second USBport,if required. USB host / slave port 1 - USBData Signal Minus with integrated pull up / pull down resistor. Module has on board 27 Ω USB series resistor. This pin can be brought out along with pin J1-22 to provide a second USB port,if required. I/O 5V safe bidirectional data / Module ground supply pin 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / 5V safe bidirectional data / control control control control control bus bus bus bus bus bit bit bit bit bit 13 14 15 16 17 I/O I/O I/O I/O I/O I/O I/O 5V 5V 5V 5V 5V 5V 5V control control control control control control control bus bus bus bus bus bus bus bit bit bit bit bit bit bit 26 27 28 29 30 31 32 safe safe safe safe safe safe safe bidirectional bidirectional bidirectional bidirectional bidirectional bidirectional bidirectional data data data data data data data / / / / / / / control bus bit 12 Copyright © 2010 Future Technology Devices International Limited 6 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Name Pin No. Pin Name on PCB Type Description J2-8 IOBUS36 IO36 I/O 5V safe bidirectional data / control bus bit 33 J2-9 IOBUS35 IO35 I/O 5V safe bidirectional data / control bus bit 34 J2-10 GND GND PWR J2-11 - - - J2-12 3V3 3V3 3.3V Output from V2DIP1’s on board 3.3V L.D.O. 3.3V output from V2DIP1’s on board 3.3V L.D.O. J2-13 3V3 3V3 3.3V Output from V2DIP1’s on board 3.3V L.D.O. 3.3V output from V2DIP1’s on board 3.3V L.D.O. J2-14 J2-15 J2-16 J2-17 J2-18 J2-19 IOBUS4 IOBUS3 IOBUS2 IOBUS1 IOBUS0 3V3 IO4 IO3 IO2 IO1 IO0 3V3 I/O I/O I/O I/O I/O 3.3V Output from VDIP1’s on board 3.3V L.D.O. 5V safe bidirectional data / control bus bit 4 5V safe bidirectional data / control bus bit 3 5V safe bidirectional data / control bus bit 2 5V safe bidirectional data / control bus bit 1 5V safe bidirectional data / control bus bit 0 3.3V output from V2DIP1’s on board 3.3V L.D.O. J2-20 PROG# PRG# Input This pin is used in combination with the RESET# pin and the UART interface to program firmware into the VNC2. J2-21 RESET# RST# Input J2-22 J2-23 J2-24 J2-25 J2-26 J2-27 J2-28 J2-29 J2-30 IOBUS25 IOBUS24 IOBUS23 GND IOBUS22 IOBUS21 IOBUS20 IOBUS19 IOBUS18 IO25 IO24 IO23 GND IO22 IO21 IO20 IO19 IO18 I/O I/O I/O PWR I/O I/O I/O I/O I/O Can be used by an external device to reset the VNC2. This pin is also used in combination with PROG# and the UART interface to program firmware into the VNC2 5V safe bidirectional data / control bus bit 25 5V safe bidirectional data / control bus bit 24 5V safe bidirectional data / control bus bit 23 Module ground supply pin 5V safe bidirectional data / control bus bit 22 5V safe bidirectional data / control bus bit 21 5V safe bidirectional data / control bus bit 20 5V safe bidirectional data / control bus bit 19 5V safe bidirectional data / control bus bit 18 Module ground supply pin Not connected Table 3.1 - Pin Signal Descriptions Copyright © 2010 Future Technology Devices International Limited 7 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.3 Default Interface I/O Pin Configuration The VNC2-64Q device device is delivered without any firmware pre-loaded. As such the IOMUX will provide a default pinout as shown in Table 3.2 Data and Control Bus Configuration Options Pin No. Pin Name on PCB Type UART Interface J2-18 IO0 I/O J2-28 IO20 I/O J2-27 IO21 I/O J2-26 IO22 I/O J2-24 IO23 I/O J2-23 IO24 I/O J2-22 IO25 I/O J1-1 IO26 I/O J1-2 IO27 I/O J1-3 IO28 I/O J1-7 IO32 I/O J1-8 IO33 I/O J1-9 IO34 I/O J2-9 IO35 I/O J2-8 IO36 I/O J2-7 IO37 I/O J2-6 IO38 I/O J2-5 IO39 I/O J2-4 IO40 I/O J2-3 IO41 I/O J2-2 IO42 I/O J2-1 IO43 I/O J2-14 IO4 I/O J1-14 IO5 I/O J1-15 IO6 I/O SPI Slave Interface SPI Master Interface Parallel FIFO Interface Debugger Interface NA NA NA NA Debug_if uart_txd NA NA NA NA uart_rxd NA NA NA NA uart_rts# NA NA NA NA uart_cts# NA NA NA NA uart_dtr# NA NA NA NA uart_dsr# NA NA NA NA uart_dcd# NA NA NA NA uart_ri# NA NA NA NA uart_tx_active NA NA NA NA NA spi_s0_clk NA NA NA NA spi_s0_mosi NA NA NA NA spi_s0_miso NA NA NA NA spi_s0_cs# NA NA NA NA spi_s1_clk NA NA NA NA spi_s1_mosi NA NA NA NA spi_s1_miso NA NA NA NA spi_s1_cs# NA NA NA NA NA spi_m_clk NA NA NA NA spi_m_mosi NA NA NA NA spi_m_miso NA NA NA NA spi_m_cs# NA NA NA NA NA fifo_data[0] NA NA NA NA fifo_data[1] NA NA NA NA fifo_data[2] NA Table 3.2 - Default Interface I/O Pin Configuration Copyright © 2010 Future Technology Devices International Limited 8 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Data and Control Bus Configuration Options Pin No. Pin Name on PCB Type J1-16 IO7 I/O J1-17 IO8 I/O J1-18 IO9 I/O J1-20 IO10 I/O J1-21 IO11 I/O J1-24 IO12 I/O J1-26 IO13 I/O J1-27 IO14 I/O J1-28 IO15 I/O J1-29 IO16 I/O UART Interface SPI Slave Interface SPI Master Interface Parallel FIFO Interface NA NA NA fifo_data[3] NA NA NA fifo_data[4] NA NA NA fifo_data[5] NA NA NA fifo_data[6] NA NA NA fifo_data[7] NA NA NA fifo_rxf# NA NA NA fifo_txe# NA NA NA fifo_rd# NA NA NA fifo_wr# NA NA NA fifo_oe# Debugger Interface NA NA NA NA NA NA NA NA NA NA Table 3.2 - Default Interface I/O Pin Configuration Copyright © 2010 Future Technology Devices International Limited 9 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.4 UART Interface When the data and control buses are configured in UART mode, the interface implements a standard asynchronous serial UART port with flow control. The UART can support baud rates from 300baud to 3Mbaud. Further details on the UART interface are available on the the Vinculum-II datasheet please refer to:- FTDI website 3.4.1 Signal Description – UART Interface The UART signals can be programmed to a choice of available I/O pins. Table 3.3 explains the available pins for each of the UART signals. Available Pins Name Type J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 uart_txd Output uart_rxd Input Receive asynchronous data input J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 uart_rts# Output Request To Send Control Output J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 uart_cts# Input J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 uart_dtr# Output uart_dsr# Input Data Request (Data Set Ready Control) Input uart_dcd# Input Data Carrier Detect Control Input Input Ring Indicator Control Input. RI# low can be used to resume the PC USB Host controller from suspend. Output Enable Transmit Data for RS485 designs. uart_tx_active may be used to signal that a transmit operation is in progress. The uart_tx_active signal will be set high one bit-time before data is transmitted and return low one bit time after the last bit of a data frame has been transmitted J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 uart_ri# uart_tx_active Description Transmit asynchronous data output Clear To Send Control Input Data Acknowledge (Data Terminal Ready Control) Output Table 3.3 - Data and Control Bus Signal Mode Options – UART Copyright © 2010 Future Technology Devices International Limited 10 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.5 Serial Peripheral Interface (SPI) The VNC2-64Q has one SPI master module and two SPI slave modules. These modules are described more fully in a Vinculum-II datasheet please refer to:- FTDI website 3.5.1 Signal Description - SPI Slave The SPI Slave signals can be programmed to a choice of available I/O pins. Table 3.4 explains the available pins for each of the SPI Slave signals. Name Type Description spi_s0_clk Input Slave clock input Input/Output Master Out Slave In Available Pins J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 spi_s1_clk spi_s0_mosi spi_s1_mosi spi_s0_miso Synchronous data from master to slave Output spi_s1_miso spi_s0_ss# Master In Slave Out Synchronous data from slave to master Input Slave chip select spi_s1_ss# Table 3.4 - Data and Control Bus Signal Mode Options – SPI Slave Copyright © 2010 Future Technology Devices International Limited 11 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.5.2 Signal Description - SPI Master The SPI Master signals can be programmed to a choice of available I/O pins. Table 3.5 shows the SPI master signals and the available pins that they can be mapped. Available Pins Name Type Description spi_m_clk Output SPI master clock input spi_m_mosi Output Master Out Slave In J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 Synchronous data from master to slave spi_m_miso Input J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 Master In Slave Out Synchronous data from slave to master spi_m_ss_0# Output Active low slave select 0 from master to slave 0 spi_m_ss_1# Output Active low slave select 1 from master to slave 1 Table 3.5 - Data and Control Bus Signal Mode Options – SPI Master Copyright © 2010 Future Technology Devices International Limited 12 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.6 Parallel FIFO Interface - Asynchronous Mode The Parallel FIFO Asynchronous mode, functionally the same as the Parallel FIFO Interface present in VDIP1, has an eight bit parallel data bus, individual read and write strobes and two hardware flow control signals. 3.6.1 Signal Description - Parallel FIFO Interface The Parallel FIFO Interface signals can be programmed to a choice of available I/O pins. Parallel FIFO Interface signals and the pins that they can be mapped Available Pins Name J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 fifo_data[0] J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 I/O FIFO data bus Bit 0 J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 fifo_data[3] J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 fifo_data[4] I/O I/O I/O I/O J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 FIFO data bus Bit 2 FIFO data bus Bit 3 FIFO data bus Bit 4 FIFO data bus Bit 5 fifo_data[5] I/O fifo_data[6] I/O J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 FIFO data bus Bit 1 fifo_data[1] fifo_data[2] J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 Description I/O J2-16, J1-15, J1-20, J1-27, J2-30, J226, J1-1, J1-5, J1-9, J2-6, J2-2 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 Type shows the FIFO data bus Bit 6 FIFO data bus Bit 7 fifo_data[7] fifo_rxf# fifo_txe# Output Output fifo_rd# Input When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by strobing RD# low, then high. When high, do not write data into the FIFO. When low, data can be written into the FIFO by strobing fifo_wr# high, then low. Enables the current FIFO data byte on D0...D7 when low. Fetches the next FIFO data byte (if available) from the receive FIFO buffer when fifo_rd# goes from high to low Writes the data byte on the D0...D7 pins into the transmit Input FIFO buffer when fifo_wr# goes from high to low. Table 3.6 - Data and Control Bus Signal Mode Options – Parallel FIFO Interface J2-15, JI-16, J1-21, J1-28, J2-29, J2-24, J1-2, J1-6, J2-9, J2-5, J2-1 fifo_wr# Copyright © 2010 Future Technology Devices International Limited 13 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.6.2 Timing Diagram – Asynchronous FIFO Mode Read and Write Cycle When in Asynchronous FIFO interface mode, the timing of a read and write operation on the FIFO interface is shown in Figure 3.3 and Table 3.7 Figure 3.3 – Asynchronous FIFO Mode Read and Write Cycle. Time Description t1 RD# inactive to RXF# t2 RXF# inactive after RD# cycle t3 RD# to Data Min Max Unit 1 14 ns 100 - ns 1 14 ns - ns t4 RD# active pulse width 30 t5 RD# active after RXF# 0 - ns t6 WR# active to TXE# inactive t7 TXE# inactive after WR# cycle 1 14 ns 100 - ns ns t8 DATA to TXE# active setup time 5 - t9 DATA hold time after WR# inactive 5 - ns 30 - ns t11 WR# active after TXE# 0 Table 3.7 - Asynchronous FIFO Mode Read Cycle Timing ns t10 WR# active pulse width In asynchronous mode an external device can control data transfer driving FIFO_WR# and FIFO_RD# inputs. In contrast to synchronous mode, in asynchronous mode the 245 FIFO module generates the output enable EN# signal. EN# signal is effectively the read signal RD#. Current byte is available to be read when FIFO_RD# goes low. When FIFO_RD# goes high, FIFO_RXF# output will also go high. It will only become low again when there is another byte to read. When FIFO_WR# goes low FIFO_TXE# flag will always go high. FIFO_TXE# goes low again only when there is still space for data to be written in to the module. Copyright © 2010 Future Technology Devices International Limited 14 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.7 Parallel FIFO Interface-Synchronous Mode The Parallel FIFO Synchronous mode has an eight bit data bus, individual read and write strobes, two hardware flow control signals, an output enable and a clock out. The synchronous FIFO mode uses the parallel FIFO interface signals detailed in Table 3.6 and additional two signals detailed Table 3.8. Available Pins J2-14, J1-17, J1-24, J1-29, J2-28, J223, J1-3, J1-7, J2-8, J2-4 J2-17, J1-14, J1-18, J1-26, J1-30, J227, J2-22, J1-4, J1-8, J2-7, J2-3 Name Type Description fifo_oe# Output FIFO Output Enable fifo_clkout Output FIFO Output Enable Table 3.8 - Data and Control Bus Signal Mode Options – Synchronous FIFO mode 3.7.1 Timing Diagram – Synchronous FIFO Mode Read and Write Cycle When in Synchronous FIFO interface mode, the timing of a read and write operation on the FIFO interface are shown in Figure 3.4 and Table 3.9 Figure 3.4 - Synchronous FIFO Mode Read and Write Cycle Copyright © 2010 Future Technology Devices International Limited 15 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Time Description Min Typical Max - 20.83 - Uni t ns t1 CLKOUT period t2 CLKOUT high period 9.38 10.42 11.46 ns t3 CLKOUT low period 9.38 10.42 11.46 ns t4 CLKOUT to RXF# 1 - 7.83 ns t5 CLKOUT to read DATA valid 1 - 7.83 ns ns t6 OE# to read DATA valid 1 - 7.83 t7 CLKOUT to OE# 1 - 7.83 ns t8 RD# setup time 12 - - ns t9 RD# hold time 0 - - ns 1 - - ns 12 - - ns 0 - - ns 12 - - ns - ns t10 CLKOUT TO TXE# t11 Write DATA setup time t12 Write DATA hold time t13 WR# setup time t14 WR# hold time 0 Table 3.9 - Synchronous FIFO Mode Read and Write Cycle Timing In synchronous mode data can be transmitted to and from the FIFO module on each clock edge. An external device synchronises to the CLKOUT output and it also has access to the output enable OE# input to control data flow. An external device should drive output enable OE# low before pulling RD# line down. When bursts of data are to be read from the module RD# should be kept low. RXF# remains low when there is still data to be read. Similarly when bursts of data are to be written to the module WR# should be kept low. TXE# remains low when there is still space available for the data to be written Copyright © 2010 Future Technology Devices International Limited 16 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 3.8 Debugger Interface The purpose of the debugger interface is to provide access to the VNC2 silicon/firmware debugger. The debug interface can be accessed via the appropriate pin on the DIL connector or more easily, it can be accessed by connecting a debug module to the J3 connector. This debug module will give access to the debugger through a USB connection to a PC via the Integrated Development Environment (IDE). The IDE is a graphical interface to the VNC2 software development tool-chain and gives the following debug capabilities through the debugger interface: Flash Erase, Write and Program. Application debug - application code can have breakpoints, be single stepped and can be halted. Detailed internal debug - memory and register read/write access. The Debugger Interface, and how to use it, is further described in the following applications Note Vinculum-II Debug Interface Description 3.8.1 ignal Description - Debugger Interface Table 3.10 shows the signals and pins description for the Debugger Interface pin header J3 Name Pin No. Name On PCB Type Description J3-1 IO0 DBG I/O Debugger Interface J3-2 - [Key] - Not connected. Used to make sure that the debug module is connected correctly. J3-3 GND GND PWR Module ground supply pin J3-4 RESET# RST# J3-5 PROG# PRG# J3-6 5V0 VCC Input Input Can be used by an external device to reset the VNCL2. This pin is also used in combination with PROG# and the UART interface to program firmware into the VNC2. This pin is used in combination with the RESET# pin and the UART interface to program firmware into the VNC2. PWR Input 5.0V module supply pin. This pin can be used to provide the 5.0V input to the V2DIP1-64 from the debugger interface when the V2DIP1-64 is not powered from the USB connector (VBUs) or the DIL connector pins J1-12, J1-13 and J1-19 and J3-6. Table 3.10 - Signal Name and Description – Debugger Interface Copyright © 2010 Future Technology Devices International Limited 17 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 4 Firmware 4.1 Firmware Support The VNC2 on the V2DIP1-64 can be programmed with the customers own firmware created using the Vinculum II firmware development tool chain or with various pre-compiled firmware profiles to allow a designer to easily change the functionality of the chip. Please refer to:- FTDI website for full details on available pre-compiled firmware 4.2 Available Firmware V2DAP firmware is currently available: USB Host for single Flash Disk and general purpose USB peripherals. Selectable UART, FIFO or SPI interface command monitor. please refer to:- FTDI website for full details. 4.3 Firmware Upgrades Refer to the debugger interface section which can be used to update the firmware. Copyright © 2010 Future Technology Devices International Limited 18 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 5 External circuit Configuration 5.1 Adding a second USB Port The external circuit configuration for adding second USB host port, with the USB activity LED, is shown below in Figure 5.1 Figure 5.1 Additional USB Port Configuration Copyright © 2010 Future Technology Devices International Limited 19 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 6 Mechanical Dimensions J2 91.53 J3 CN1 1.28 4.98 22.95 12.32 6.33 J1 4.94 10.32 18.01 YYWW FTDI VNC2-64Q1A XXXXXXXX 21.60 U1 10.98 13.52 84.64 86.24 4.90 1.60 7.00 17.85 8.65 Figure 6.1 - V2DIP1-64 Dimensions (Top View) 2.54 Figure 6.2 - V2DIP1-64 Dimensions (Side View) ±0.20mm Tolerance (except pitch) All dimensions are in mm. Copyright © 2010 Future Technology Devices International Limited 20 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 7 Schematic Diagram Figure 7.1 - V2DIP1-64 Schematics Copyright © 2010 Future Technology Devices International Limited 21 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 8 Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No 516, Sec. 1 NeiHu Road Taipei 114 Taiwan, R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) [email protected] E-Mail (Support) [email protected] E-Mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Branch Office – Shanghai, China Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, ChangNing District, ShangHai, China Tel: +86 (21) 62351596 Fax: +86(21) 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2010 Future Technology Devices International Limited 22 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Appendix A – References Application and Technical Notes Vinculum-II IO Cell Description Vinculum-II Debug Interface Description Vinculum-II IO Mux Explained Vinculum-II PWM Example Migrating Vinculum Designs From VNC1L to VNC2-48L1A Vinculum-II Errata Technical Note Copyright © 2010 Future Technology Devices International Limited 23 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Appendix B – List of Figures and Tables List of Figures Figure 1.1 - V2DIP1 64 .................................................................................................................. 1 Figure 3.1 - V2DIP1-64 Module Pin Out (Top View) .......................................................................... 4 Figure 3.2 - V2DIP1-64 Module Pin Out (Bottom View) ..................................................................... 5 Figure 3.3 – Asynchronous FIFO Mode Read and Write Cycle. ........................................................... 14 Figure 3.4 - Synchronous FIFO Mode Read and Write Cycle .............................................................. 15 Figure 5.1 Additional USB Port Configuration .................................................................................. 19 Figure 6.1 - V2DIP1-64 Dimensions (Top View) .............................................................................. 20 Figure 6.2 - V2DIP1-64 Dimensions (Side View) ............................................................................. 20 Figure 7.1 - V2DIP1-64 Schematics............................................................................................... 21 List of Tables Table 3.1 - Pin Signal Descriptions .................................................................................................. 6 Table 3.2 - Default Interface I/O Pin Configuration ........................................................................... 8 Table 3.3 - Data and Control Bus Signal Mode Options – UART ......................................................... 10 Table 3.4 - Data and Control Bus Signal Mode Options – SPI Slave ................................................... 11 Table 3.5 - Data and Control Bus Signal Mode Options – SPI Master ................................................. 12 Table 3.6 - Data and Control Bus Signal Mode Options – Parallel FIFO Interface ................................. 13 Table 3.7 - Asynchronous FIFO Mode Read Cycle Timing .................................................................. 14 Table 3.8 - Data and Control Bus Signal Mode Options – Synchronous FIFO mode .............................. 15 Table 3.9 - Synchronous FIFO Mode Read and Write Cycle Timing .................................................... 16 Table 3.10 - Signal Name and Description – Debugger Interface ....................................................... 17 Copyright © 2010 Future Technology Devices International Limited 24 Document Reference No.: FT_000165 V2DIP1-64 VNCL2-64Q Development Module Datasheet Version 1.01 Clearance No.: FTDI# 154 Appendix C – Revision History Version 1.0 First Release 19th April 2010 Version 1.01 Updated module’s images, mechanical drawings and Figure 5.1 25th May 2010 Copyright © 2010 Future Technology Devices International Limited 25