tsv711

TSV711, TSV712, TSV714
High accuracy (200 μV) micropower 14 μA, 150 kHz
5 V CMOS operational amplifiers
Datasheet - preliminary data
Benefits
Single (TSV711)
• Higher accuracy without calibration
• Energy saving
• Guaranteed operation on low-voltage battery
SC70-5
Related products
• See the TSV73 series (900 kHz for 60 μA) for
higher gain bandwidth products
Dual (TSV712)
Applications
• Battery powered applications
DFN8 2x2
MiniSO-8
• Portable devices
• Signal conditioning
Quad (TSV714)
• Active filtering
• Medical instrumentation
Description
QFN16 3x3
The TSV71x series of single, dual, and quad
operational amplifiers offer low-voltage operation,
rail-to-rail input and output, and excellent
accuracy (Vio lower than 200 μV at 25 ° C).
TSSOP14
These devices benefit from STMicroelectronics®
5 V CMOS technology and offer an excellent
speed/power consumption ratio (150 kHz typical
gain bandwidth) while consuming less than 14 μA
at 5 V. The TSV71x series also feature an
ultra-low input bias current.
Features
• Low offset voltage: 200 µV max.
• Low power consumption: 10 µA at 5 V
• Low supply voltage: 1.5 V to 5.5 V
The single version (TSV711), the dual version
(TSV712), and the quad version (TSV714) are
housed in the smallest industrial packages.
• Gain bandwidth product: 150 kHz typ.
• Low input bias current: 1 pA typ.
These characteristics make the TSV71x family
ideal for sensor interfaces, battery-powered and
portable applications, and active filtering.
• Rail-to-rail input and output
• EMI hardened operational amplifiers
• High tolerance to ESD: 4 kV HBM
• Extended temperature range: -40 to +125 °C
March 2013
DocID023707 Rev 2
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to
change without notice.
1/29
www.st.com
29
Contents
TSV711, TSV712, TSV714
Contents
1
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
4.1
Operating voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2
Rail-to-rail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.3
Rail-to-rail output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.4
Input offset voltage drift over temperature . . . . . . . . . . . . . . . . . . . . . . . . 16
4.5
Long-term input offset voltage drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.6
Initialization time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.7
PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.8
Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.1
SC70-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.2
DFN8 2x2 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.3
MiniSO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.4
QFN16 3x3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.5
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
Pin connections
Figure 1. Pin connections (top view)
Single
9&&
,1 9&&
,1 287
SC70-5 (TSV711)
Dual
287
9&&
287
9&&
,1
287
,1
287
,1
,1
,1
,1
9&&
,1
9&&
,1
DFN8 2x2 (TSV712)
MiniSO-8 (TSV712)
1&
,1
287
287
,1
1&
,1
9&&
287
287
,1
,1
Quad
,1
1
Pin connections
,1
9&&
1&
,1
QFN16 3x3 (TSV714)
TSSOP14 (TSV714)
1. The exposed pads of the QFN16 3x3 can be connected to VCC- or left floating.
DocID023707 Rev 2
3/29
Absolute maximum ratings and operating conditions
2
TSV711, TSV712, TSV714
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings (AMR)
Symbol
VCC
Vid
Vin
Iin
Tstg
Rthja
Rthjc
Tj
Parameter
Supply voltage
(2)
±VCC
V
(3)
VCC- - 0.2 to VCC++ 0.2
(4)
10
mA
-65 to +150
°C
Input voltage
Storage temperature
Thermal resistance junction-to-ambient
SC70-5
DFN8 2x2
MiniSO8
QFN16 3x3
TSSOP14
(5)(6)
205
120
190
45
100
°C/W
Thermal resistance junction-to-case
DFN8 2x2
33
Maximum junction temperature
150
°C
4
kV
HBM: human body
ESD
Unit
6
Differential input voltage
Input current
Value
(1)
model(7)
MM: machine model for
TSV711(8)
150
MM: machine model for
TSV712(8)
200
MM: machine model for
TSV714(8)
CDM: charged device model except
V
300
MiniSO8(9)
1.5
(9)
1.3
CDM: charged device model for MiniSO8
Latchup immunity
200
kV
mA
1. All voltage values, except the differential voltage are with respect to the network ground terminal.
2. The differential voltage is a non-inverting input terminal with respect to the inverting input terminal. The
TSV712 and TSV714 devices include an internal differential voltage limiter that clamps internal differential
voltage at 0.5 V.
3. VCC - Vin must not exceed 6 V, Vin must not exceed 6 V.
4. Input current must be limited by a resistor in series with the inputs.
5. Short-circuits can cause excessive heating and destructive dissipation.
6. Rth are typical values.
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
8. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
9. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to ground.
4/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
Absolute maximum ratings and operating conditions
Table 2. Operating conditions
Symbol
Parameter
VCC
Supply voltage
Vicm
Common mode input voltage range
Toper
Operating free air temperature range
Value
1.5 to 5.5
DocID023707 Rev 2
VCC- - 0.1 to VCC+ + 0.1
-40 to +125
Unit
V
°C
5/29
Electrical characteristics
3
TSV711, TSV712, TSV714
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = 1.8 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C, and
RL = 10 kΩ connected to VCC/2 (unless otherwise specified)
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
DC performance
Vio
ΔVio/ΔT
Iio
Iib
Input offset voltage
(Vicm = 0 V)
T = 25 °C
200
-40 °C < T< 85 °C
850
-40 °C < T< 125 °C
1200
(1)
Input offset voltage drift
-40 °C < T< 125 °C
Input offset current
(Vout = VCC/2)
T = 25 °C
1
10(2)
-40 °C < T< 125 °C
1
300(2)
T = 25 °C
1
10(2)
-40 °C < T< 125 °C
1
300(2)
Input bias current (Vout = VCC/2)
10
Common mode rejection ratio
20 log (ΔVicm/ΔVio)
Vicm = 0 V to VCC,
Vout = VCC/2, RL > 1 MΩ
T = 25 °C
69
-40 °C < T< 125 °C
61
Avd
Large signal voltage gain
Vout = 0.5 V to (VCC - 0.5 V)
T = 25 °C
95
-40 °C < T< 125 °C
85
VOH
High level output voltage
(VOH = VCC - Vout)
T = 25 °C
75
-40 °C < T< 125 °C
80
T = 25 °C
40
-40 °C < T< 125 °C
60
CMR
VOL
Low level output voltage
Isink (Vout = VCC)
Iout
Isource (Vout = 0 V)
ICC
6/29
Supply current (per channel,
Vout = VCC/2, RL > 1 MΩ)
T = 25 °C
6
-40 °C < T< 125 °C
4
T = 25 °C
5
-40 °C < T< 125 °C
3
T = 25 °C
-40 °C < T< 125 °C
DocID023707 Rev 2
μV
μV/°C
pA
88
dB
mV
12
mA
7
9
14
16
µA
TSV711, TSV712, TSV714
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = 1.8 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C, and
RL = 10 kΩ connected to VCC/2 (unless otherwise specified) (continued)
Symbol
Parameter
Conditions
Min.
Typ.
100
120
Max.
Unit
AC performance
GBP
Gain bandwidth product
Fu
Unity gain frequency
Φm
Phase margin
Gm
Gain margin
SR
Slew rate(3)
en
Equivalent input noise voltage
tinit
Initialization time(4)
RL = 10 kΩ, CL = 100 pF
kHz
100
45
Degrees
19
dB
RL = 10 kΩ, CL = 100 pF,
Vout = 0.5 V to VCC - 0.5 V
0.04
V/μs
f = 1 kHz
100
f = 10 kHz
96
nV
-----------Hz
T = 25 °C
5
-40 °C < T< 125 °C
60
ms
1. See Section 4.4: Input offset voltage drift over temperature.
2. Guaranteed by characterization.
3. Slew rate value is calculated as the average between positive and negative slew rates.
4. Initialization time is defined as the delay after power-up to guarantee operation within specified performances. Guaranteed
by design. See Section 4.6: Initialization time.
DocID023707 Rev 2
7/29
Electrical characteristics
TSV711, TSV712, TSV714
Table 4. Electrical characteristics at VCC+ = 3.3 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C, and
RL = 10 kΩ connected to VCC/2 (unless otherwise specified)
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
DC performance
Vio
Input offset voltage
T = 25 °C
200
-40 °C < T< 85 °C
850
-40 °C < T< 125 °C
ΔVio/ΔT
ΔVio
Iio
Iib
CMR
-40 °C < T< 125 °C
Long-term input offset voltage
drift
T = 25 °C(2)
Input offset current
(Vout = VCC/2)
Input bias current (Vout = VCC/2)
1200
(1)
Input offset voltage drift
10
month
(3)
1
10
-40 °C < T< 125 °C
1
300(3)
T = 25 °C
1
10(3)
-40 °C < T< 125 °C
1
300(3)
80
69
dB
Large signal voltage gain
Vout = 0.5 V to (VCC - 0.5 V)
T = 25 °C
95
-40 °C < T< 125 °C
85
VOH
High level output voltage
(VOH = VCC - Vout)
T = 25 °C
75
-40 °C < T< 125 °C
80
T = 25 °C
40
-40 °C < T< 125 °C
60
Low level output voltage
Isink (Vout = VCC)
Iout
Isource (Vout = 0 V)
ICC
8/29
Supply current (per channel,
Vout = VCC/2, RL > 1 MΩ)
T = 25 °C
20
-40 °C < T< 125 °C
15
T = 25 °C
20
-40 °C < T< 125 °C
15
T = 25 °C
-40 °C < T< 125 °C
DocID023707 Rev 2
pA
100
Avd
VOL
μV/°C
μV
---------------------------
0.3
T = 25 °C
T = 25 °C
Common mode rejection ratio
20 log (ΔVicm/ΔVio)
Vicm = 0 V to VCC, Vout = VCC/2, -40 °C < T< 125 °C
RL > 1 MΩ
μV
mV
34
mA
26
9
14
16
µA
TSV711, TSV712, TSV714
Electrical characteristics
Table 4. Electrical characteristics at VCC+ = 3.3 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C, and
RL = 10 kΩ connected to VCC/2 (unless otherwise specified) (continued)
Symbol
Parameter
Conditions
Min.
Typ.
100
120
Max.
Unit
AC performance
GBP
Gain bandwidth product
Fu
Unity gain frequency
Φm
Phase margin
Gm
Gain margin
SR
Slew rate(4)
en
Equivalent input noise voltage
tinit
Initialization time(5)
RL = 10 kΩ, CL = 100 pF
kHz
100
45
Degrees
19
dB
RL = 10 kΩ, CL = 100 pF,
Vout = 0.5 V to VCC - 0.5 V
0.05
V/μs
f = 1 kHz
100
f = 10 kHz
96
nV
-----------Hz
T = 25 °C
5
-40 °C < T< 125 °C
50
ms
1. See Section 4.4: Input offset voltage drift over temperature.
2. Typical value is based on the Vio drift observed after 1000h at 125 °C extrapolated to 25 °C using the Arrhenius law and
assuming an activation energy of 0.7 eV. The operational amplifier is aged in follower mode configuration. See Section 4.5:
Long-term input offset voltage drift.
3. Guaranteed by characterization.
4. Slew rate value is calculated as the average between positive and negative slew rates.
5. Initialization time is defined as the delay after power-up which guarantees operation within specified performances.
Guaranteed by design. See Section 4.6: Initialization time.
DocID023707 Rev 2
9/29
Electrical characteristics
TSV711, TSV712, TSV714
Table 5. Electrical characteristics at VCC+ = 5 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C,
and RL = 10 kΩ connected to VCC/2 (unless otherwise specified)
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
DC performance
Vio
Input offset voltage
T = 25 °C
200
-40 °C < T< 85 °C
850
-40 °C < T< 125 °C
ΔVio/ΔT
ΔVio
Input offset voltage drift
-40 °C < T< 125 °C
Long-term input offset voltage
drift
T = 25 °C(2)
Iio
Input offset current
(Vout = VCC/2)
Iib
Input bias current
(Vout = VCC/2)
1200
(1)
10
1
10
-40 °C < T< 125 °C
1
300(3)
T = 25 °C
1
10(3)
-40 °C < T< 125 °C
1
300(3)
CMR
T = 25 °C
71
SVR
Supply voltage rejection ratio
20 log (ΔVCC/ΔVio)
VCC = 1.5 to 5.5 V, Vic = 0 V,
RL > 1 MΩ
-40 °C < T< 125 °C
71
Avd
Large signal voltage gain
Vout = 0.5 V to (VCC - 0.5 V)
T = 25 °C
95
-40 °C < T< 125 °C
85
VOH
VOL
dB
VRF = 100 mVRFpeak, f = 900 MHz
50(4)
EMIRR = 20 log (VRFpeak/ΔVio)
VRF = 100 mVRFpeak, f = 1800 MHz
60(4)
VRF = 100 mVRFpeak, f = 2400 MHz
63(4)
Iout
Isource (Vout = 0 V)
10/29
90
EMI rejection ratio
Isink (Vout = VCC)
ICC
73
38(4)
Low level output voltage
Supply current (per channel,
Vout = VCC/2, RL > 1 MΩ)
T = 25 °C
75
-40 °C < T< 125 °C
80
T = 25 °C
40
-40 °C < T< 125 °C
60
T = 25 °C
35
-40 °C < T< 125 °C
20
T = 25 °C
35
-40 °C < T< 125 °C
20
T = 25 °C
-40 °C < T< 125 °C
DocID023707 Rev 2
pA
94
VRF = 100 mVRFpeak, f = 400 MHz
High level output voltage
(VOH = VCC - Vout)
month
(3)
T = 25 °C
74
μV/°C
μV
---------------------------
0.7
Common mode rejection ratio T = 25 °C
20 log (ΔVicm/ΔVio)
Vicm = 0 V to VCC,
-40 °C < T< 125 °C
Vout = VCC/2, RL > 1 MΩ
EMIRR
μV
mV
56
mA
45
10
14
16
µA
TSV711, TSV712, TSV714
Electrical characteristics
Table 5. Electrical characteristics at VCC+ = 5 V with VCC- = 0 V, Vicm = VCC/2, T = 25 °C,
and RL = 10 kΩ connected to VCC/2 (unless otherwise specified) (continued)
Symbol
Parameter
Conditions
Min.
Typ.
110
150
Max.
Unit
AC performance
GBP
Gain bandwidth product
Fu
Unity gain frequency
Φm
Phase margin
Gm
Gain margin
SR
Slew rate(5)
∫ en
Low-frequency peak-to-peak
input noise
en
THD+N
tinit
RL = 10 kΩ, CL = 100 pF
kHz
120
45
Degrees
19
dB
RL = 10 kΩ, CL = 100 pF,
Vout = 0.5 V to VCC - 0.5 V
0.06
V/μs
Bandwidth: f = 0.1 to 10 Hz
10
µVpp
f = 1 kHz
100
f = 10 kHz
96
nV
-----------Hz
Equivalent input noise voltage
Total harmonic distortion +
noise
Initialization time(6)
fin = 1 kHz, ACL = 1,
RL = 100 kΩ, Vicm = (VCC - 1 V)/2,
BW = 22 kHz, Vout = 0.5 Vpp
0.008
%
T = 25 °C
5
-40 °C < T< 125 °C
50
ms
1. See Section 4.4: Input offset voltage drift over temperature.
2. Typical value is based on the Vio drift observed after 1000h at 125 °C extrapolated to 25 °C using the Arrhenius law and
assuming an activation energy of 0.7 eV. The operational amplifier is aged in follower mode configuration. See Section 4.5:
Long-term input offset voltage drift.
3. Guaranteed by characterization.
4. Tested on SC70-5 package.
5. Slew rate value is calculated as the average between positive and negative slew rates.
6. Initialization time is defined as the delay after power-up to guarantee operation within specified performances. Guaranteed
by design. See Section 4.6: Initialization time.
DocID023707 Rev 2
11/29
Electrical characteristics
TSV711, TSV712, TSV714
Figure 2. Supply current vs. supply voltage
at Vicm = VCC/2
Figure 3. Input offset voltage distribution
at VCC = 5 V, Vicm = VCC/2
Figure 4. Input offset voltage distribution
at VCC = 3.3 V, Vicm = VCC/2
Figure 5. Input offset voltage temperature
coefficient distribution
30
Population (%)
25
VCC = 3.3 V
Vicm = 1.65 V
T = 25 ˚C
20
15
10
5
0
-250
-200
-150
-100
-50
0
50
100
150
200
250
Input offset voltage (µV)
Figure 7. Input offset voltage vs. temperature
Figure 6. Input offset voltage vs. input common
mode voltage
12/29
DocID023707 Rev 2
Figure 8. Output current vs. output voltage
at VCC = 1.5 V
Figure 9. Output current vs. output voltage
at VCC = 5 V
Electrical characteristics
TSV711, TSV712, TSV714
Figure 11. Bode diagram at VCC = 1.5 V
Figure 10. Output current vs. supply voltage
Figure 13. Closed-loop gain diagram
vs. capacitive load
Figure 12. Bode diagram at VCC = 5 V
DocID023707 Rev 2
13/29
Electrical characteristics
TSV711, TSV712, TSV714
Figure 15. Negative slew rate
Figure 14. Positive slew rate
Figure 17. Noise vs. frequency
Figure 16. Slew rate vs. supply voltage
Figure 19. THD+N vs. frequency
Figure 18. 0.1 Hz to 10 Hz noise
14/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
Electrical characteristics
Figure 21. Output impedance vs. frequency
in closed-loop configuration
Figure 20. THD+N vs. output voltage
DocID023707 Rev 2
15/29
Application information
TSV711, TSV712, TSV714
4
Application information
4.1
Operating voltages
The TSV71x series of devices can operate from 1.5 V to 5.5 V. The parameters are fully
specified for 1.8 V, 3.3 V, and 5 V power supplies. However, they are very stable in the full
VCC range and several characterization curves show TSV71x device characteristics at 1.5 V.
In addition, the main specifications are guaranteed in the extended temperature range from
-40 °C to +125 °C.
4.2
Rail-to-rail input
The TSV711, TSV712, and TSV714 devices have a rail-to-rail input, and the input common
mode range is extended from VCC-- 0.1 V to VCC+ + 0.1 V.
4.3
Rail-to-rail output
The output levels of the TSV71x operational amplifiers can go close to the rails: to a
maximum of 40 mV below the upper rail and to a maximum of 75 mV above the lower rail
when a 10 kΩ resistive load is connected to VCC/2.
4.4
Input offset voltage drift over temperature
The maximum input voltage drift over the temperature variation is defined as the offset
variation related to offset value measured at 25 °C. The operational amplifier is one of the
main circuits of the signal conditioning chain, and the amplifier input offset is a major
contributor to the chain accuracy. The signal chain accuracy at 25 °C can be compensated
during production at application level. The maximum input voltage drift over temperature
enables the system designer to anticipate the effect of temperature variations.
The maximum input voltage drift over temperature is computed using Equation 1.
Equation 1
ΔV io
V io ( T ) – V io ( 25° C )
------------ = max -------------------------------------------------ΔT
T – 25° C
with T = -40 °C and 125 °C.
The datasheet maximum value is guaranteed by a measurement on a representative
sample size ensuring a Cpk (process capability index) greater than 1.33.
16/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
4.5
Application information
Long-term input offset voltage drift
To evaluate product reliability, two types of stress acceleration are used:
•
Voltage acceleration, by changing the applied voltage
•
Temperature acceleration, by changing the die temperature (below the maximum
junction temperature allowed by the technology) with the ambient temperature.
The voltage acceleration has been defined based on JEDEC results, and is defined using
Equation 2.
Equation 2
A FV = e
β ⋅ ( VS – VU )
Where:
AFV is the voltage acceleration factor
β is the voltage acceleration constant in 1/V, constant technology parameter (β = 1)
VS is the stress voltage used for the accelerated test
VU is the voltage used for the application
The temperature acceleration is driven by the Arrhenius model, and is defined in Equation 3.
Equation 3
A FT = e
Ea ⎛ 1
1
------ ⋅ ------ – ------⎞
⎝ T U T S⎠
k
Where:
AFT is the temperature acceleration factor
Ea is the activation energy of the technology based on the failure rate
k is the Boltzmann constant (8.6173 x 10-5 eV.K-1)
TU is the temperature of the die when VU is used (K)
TS is the temperature of the die under temperature stress (K)
The final acceleration factor, AF, is the multiplication of the voltage acceleration factor and
the temperature acceleration factor (Equation 4).
Equation 4
A F = A FT × A FV
AF is calculated using the temperature and voltage defined in the mission profile of the
product. The AF value can then be used in Equation 5 to calculate the number of months of
use equivalent to 1000 hours of reliable stress duration.
DocID023707 Rev 2
17/29
Application information
TSV711, TSV712, TSV714
Equation 5
Months = A F × 1000 h × 12 months ⁄ ( 24 h × 365.25 days )
To evaluate the op-amp reliability, a follower stress condition is used where VCC is defined
as a function of the maximum operating voltage and the absolute maximum rating (as
recommended by JEDEC rules).
The Vio drift (in µV) of the product after 1000 h of stress is tracked with parameters at
different measurement conditions (see Equation 6).
Equation 6
V CC = maxV op with V icm = V CC ⁄ 2
The long term drift parameter (ΔVio), estimating the reliability performance of the product, is
obtained using the ratio of the Vio (input offset voltage value) drift over the square root of the
calculated number of months (Equation 7).
Equation 7
V io drift
ΔV io = -----------------------------( months )
where Vio drift is the measured drift value in the specified test conditions after 1000 h stress
duration.
18/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
4.6
Application information
Initialization time
The TSV71x series of devices use a proprietary trimming topology that is initiated at each
device power-up and allows excellent Vio performance to be achieved. The initialization time
is defined as the delay after power-up which guarantees operation within specified
performances. During this period, the current consumption (ICC) and the input offset voltage
(Vio) can be different to the typical ones.
Figure 22. Initialization phase
The initialization time is VCC and temperature dependent. Table 6 sums up the
measurement results for different supply voltages and for temperatures varying from -40 °C
to 125 °C.
Table 6. Initialization time measurement results
Temperature: -40 °C
VCC (V)
4.7
Temperature: 25 °C
Temperature: 125 °C
Tinit (ms)
ICC phase 1 (mA)
Tinit (ms)
ICC phase 1 (mA)
Tinit (ms)
ICC phase 1 (mA)
1.8
37
0.33
3.2
0.40
0.35
0.46
3.3
2.9
1.4
0.95
1.3
0.34
1.2
5
2.4
3.2
0.85
2.4
0.31
2.9
PCB layouts
For correct operation, it is advised to add a 10 nF decoupling capacitors as close as
possible to the power supply pins.
DocID023707 Rev 2
19/29
Application information
4.8
TSV711, TSV712, TSV714
Macromodel
Accurate macromodels of the TSV71x devices are available on the STMicroelectronics’
website at www.st.com. These model are a trade-off between accuracy and complexity (that
is, time simulation) of the TSV71x operational amplifiers. They emulate the nominal
performance of a typical device within the specified operating conditions mentioned in the
datasheet. They also help to validate a design approach and to select the right operational
amplifier, but they do not replace on-board measurements.
20/29
DocID023707 Rev 2
TSV711, TSV712, TSV714
5
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
DocID023707 Rev 2
21/29
Package information
5.1
TSV711, TSV712, TSV714
SC70-5 package information
Figure 23. SC70-5 package mechanical drawing
SIDE VIEW
DIMENSIONS IN MM
GAUGE PLANE
COPLANAR LEADS
SEATING PLANE
TOP VIEW
Table 7. SC70-5 package mechanical data
Dimensions
Symbol
Millimeters
Min.
22/29
Typ.
Inches
Max.
Min.
0.032
A
0.80
1.10
A1
0
0.10
A2
0.80
b
0.90
Typ.
Max.
0.043
0.004
1.00
0.032
0.035
0.15
0.30
0.006
0.012
c
0.10
0.22
0.004
0.009
D
1.80
2.00
2.20
0.071
0.079
0.087
E
1.80
2.10
2.40
0.071
0.083
0.094
E1
1.15
1.25
1.35
0.045
0.049
0.053
e
0.65
0.025
e1
1.30
0.051
L
0.26
<
0°
0.36
0.46
0.010
8°
0°
DocID023707 Rev 2
0.014
0.039
0.018
8°
TSV711, TSV712, TSV714
DFN8 2x2 package information
Figure 24. DFN8 2x2 package mechanical drawing
'
$
%
& [
(
3,1,1'(;$5($
& [
7239,(:
$
&
$
&
6($7,1*
3/$1(
6,'(9,(:
&
H
ESOFV
3,1,1'(;$5($
& $ %
3LQ,'
/
5.2
Package information
%277209,(:
*$06&%
Table 8. DFN8 2x2 package mechanical data
Dimensions
Ref.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
0.70
0.75
0.80
0.028
0.030
0.031
A1
0.00
0.02
0.05
0.000
0.001
0.002
b
0.15
0.20
0.25
0.006
0.008
0.010
D
2.00
0.079
E
2.00
0.079
e
0.50
0.020
L
N
0.045
0.55
0.65
8
DocID023707 Rev 2
0.018
0.022
0.026
8
23/29
Package information
5.3
TSV711, TSV712, TSV714
MiniSO-8 package information
Figure 25. MiniSO-8 package mechanical drawing
Table 9. MiniSO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.1
A1
0
A2
0.75
b
Max.
0.043
0.15
0
0.95
0.030
0.22
0.40
0.009
0.016
c
0.08
0.23
0.003
0.009
D
2.80
3.00
3.20
0.11
0.118
0.126
E
4.65
4.90
5.15
0.183
0.193
0.203
E1
2.80
3.00
3.10
0.11
0.118
0.122
e
L
0.85
0.65
0.40
0.60
0.006
0.033
0.80
0.016
0.024
0.95
0.037
L2
0.25
0.010
ccc
0°
0.037
0.026
L1
k
24/29
Inches
8°
0.10
DocID023707 Rev 2
0°
0.031
8°
0.004
TSV711, TSV712, TSV714
5.4
Package information
QFN16 3x3 package information
Figure 26. QFN16 3x3 package mechanical drawing
4)1B[B9BB&
DocID023707 Rev 2
25/29
Package information
TSV711, TSV712, TSV714
Table 10. QFN16 3x3 mm package mechanical data (pitch 0.5 mm)
Dimensions
Ref.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
0.80
0.90
1.00
0.031
0.035
0.039
A1
0
0.05
0
A3
0.20
b
0.18
D
2.90
D2
1.50
E
2.90
E2
1.50
e
L
3.00
3.00
0.008
0.30
0.007
3.10
0.114
1.80
0.059
3.10
0.114
1.80
0.059
0.50
0.30
0.002
0.012
0.118
0.071
0.118
0.122
0.071
0.020
0.50
0.012
Figure 27. QFN16 3x3 footprint recommendation
4)1B[B9BIRRWSULQWBB&
26/29
0.122
DocID023707 Rev 2
0.020
TSV711, TSV712, TSV714
5.5
Package information
TSSOP14 package information
Figure 28. TSSOP14 package mechanical drawing
Table 11. TSSOP14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.90
5.00
5.10
0.193
0.197
0.201
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.176
e
L
0.65
0.45
L1
k
aaa
1.00
0.60
0.0256
0.75
0.018
1.00
0°
0.024
0.030
0.039
8°
0.10
DocID023707 Rev 2
0°
8°
0.004
27/29
Ordering information
6
TSV711, TSV712, TSV714
Ordering information
Table 12. Order codes
Order code
Temperature
range
TSV711ICT
TSV712IQ2T
TSV712IST
-40° C to +125° C
TSV714IQ4T
TSV714IPT
7
Package
Packaging
Marking
SC70-5
K1W
DFN8 2x2
K1W
MiniSO8
Tape and reel
V712
QFN16 3x3
K1W
TSSOP14
TSV714IP
Revision history
Table 13. Document revision history
Date
Revision
26-Sep-2012
1
Initial internal release
2
Initial public release.
Datasheet updated for two new products: TSV712 and
TSV714.
Four new packages added: DFN8 2x2, MiniSO-8,
QFN16 3x3, and TSSOP14.
Updated Table 3, Table 4, and Table 5.
Section 4: Application information: re-written
26-Mar-2013
28/29
Changes
DocID023707 Rev 2
TSV711, TSV712, TSV714
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID023707 Rev 2
29/29