TSV622, TSV623, TSV624, TSV625 Rail-to-rail input/output 29 µA 420 kHz CMOS operational amplifiers Features ■ Rail-to-rail input and output ■ Low power consumption: 29 µA typ, 36 µA max ■ Low supply voltage: 1.5 – 5.5 V ■ Gain bandwidth product: 420 kHz typ ■ Unity gain stability ■ Low power shutdown mode: 5 nA typ ■ Good accuracy: 800 µV max (A version) ■ Low input bias current: 1 pA typ ■ Micropackages: MiniSO-8, SOT23-8, MiniSO-10, TSSOP14, TSSOP16 ■ EMI hardened operational amplifiers ■ High tolerance to ESD: 4 kV HBM ■ Extended temperature range: -40 to +125° C SOT23-8 SO-8 MiniSO-8 Applications ■ Battery-powered applications ■ Portable devices ■ Signal conditioning ■ Active filtering ■ Medical instrumentation TSSOP-14 Description TSSOP-16 The TSV622, TSV623, TSV624 and TSV625 dual and quad operational amplifiers offer low voltage, low power operation and rail-to-rail input and output. The TSV62x series features an excellent speed/power consumption ratio, offering a 420 kHz gain bandwidth product while consuming only 29 µA at a 5 V supply voltage. These opamps are unity gain stable for capacitive loads up to 100 pF. They also feature an ultra-low input bias current and low input offset voltage. June 2009 TSV623 (dual) and TSV625 (quad) have two shutdown pins in order to reduce power consumption. These features make the TSV62x family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. Doc ID 15689 Rev 2 1/25 www.st.com 25 Contents TSV62x Contents 1 Package pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 4.1 Operating voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.2 Rail-to-rail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.3 Rail-to-rail output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.4 Optimization of DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.5 Shutdown function (TSV623, TSV625) . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.6 Driving resistive and capacitive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.7 PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.8 Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.1 SOT23-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.2 SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.3 MiniSO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.4 MiniSO-10 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.5 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.6 TSSOP16 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2/25 Doc ID 15689 Rev 2 TSV62x 1 Package pin connections Package pin connections Figure 1. Pin connections for each package (top view) Out1 1 In1- 2 _ In1+ 3 + VCC- 4 Out1 1 10 VCC+ 8 VCC+ In1- 2 _ 7 Out2 In1+ 3 + _ 6 In2- VCC- 4 + 5 In2+ SHDN1 5 Out1 14 Out4 1 In1- 2 _ _ 13 In4- In1+ 3 + + 12 In4+ VCC+ 4 In2+ 5 In2- 6 Out2 7 + _ In3- 8 Out3 8 In2- + 7 In2+ 6 SHDN2 16 Out4 1 2 _ 15 In4- In1+ 3 + + 14 In4+ VCC+ 4 In2+ 5 In2- 6 Out2 7 10 Out3 SHDN1/2 8 9 In1- 10 In3+ 9 _ _ 11 VCC+ _ Out2 TSV623IST MiniSO-10 TSV622IDT/IST/ILT SO8/Mini-SO8/SOT23-8 Out1 9 13 VCC+ _ + _ 12 In3+ 11 In3- SHDN3/4 TSV625IPT TSSOP16 TSV624IPT TSSOP14 Doc ID 15689 Rev 2 3/25 Absolute maximum ratings and operating conditions 2 TSV62x Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings (AMR) Symbol VCC Vid Vin Iin SHDN Parameter (1) Supply voltage Differential input voltage Input voltage (3) Input current (4) (2) (3) Shutdown voltage Value Unit 6 V ±VCC V VCC- - 0.2 to VCC++ 0.2 V 10 mA VCC- - 0.2 to VCC++ 0.2 V -65 to +150 °C Tstg Storage temperature Rthja Thermal resistance junction to ambient(5)(6) SOT23-8 MiniSO-8 SO-8 Mini-SO10 TSSOP14 TSSOP16 105 190 125 113 100 95 Maximum junction temperature 150 °C 4 kV 200 V 1.5 kV 200 mA Tj HBM: human body ESD MM: machine model(7) model(8) CDM: charged device model(9) Latch-up immunity °C/W 1. All voltage values, except differential voltages are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. VCC-Vin must not exceed 6 V, Vin must not exceed 6V. 4. Input current must be limited by a resistor in series with the inputs. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to ground. Table 2. Operating conditions Symbol 4/25 Parameter VCC Supply voltage Vicm Common mode input voltage range Toper Operating free air temperature range Doc ID 15689 Rev 2 Value Unit 1.5 to 5.5 V VCC- - 0.1 to VCC+ + 0.1 V -40 to +125 °C TSV62x Electrical characteristics 3 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +1.8 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, and RL connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit TSV62x TSV62xA TSV623AIST - MiniSO10 4 0.8 1 mV TSV62x -Tmin < Top < Tmax TSV62xA - Tmin < Top < Tmax TSV623AIST - Tmin < Top < Tmax 6 2 2.2 DC performance Vio DVio Iio Iib CMR Offset voltage Input offset voltage drift Input offset current (Vout = VCC/2) Input bias current (Vout = VCC/2) Common mode rejection ratio 20 log (ΔVic/ΔVio) Tmin < Top < Tmax Tmin < Top < Tmax 0 V to 1.8 V, Vout = 0.9 V 53 Tmin < Top < Tmax 51 RL= 10 kΩ, Vout= 0.5 V to 1.3 V 78 Tmin < Top < Tmax 73 35 50 Avd Large signal voltage gain VOH High level output voltage RL = 10 kΩ Tmin < Top < Tmax VOL Low level output voltage RL = 10 kΩ Tmin < Top < Tmax Isink Iout Isource ICC Supply current (per operator) μV/°C 2 1 10 (1) pA 1 100 pA 1 10 (1) pA 1 100 pA 74 dB 95 6 Tmin < Top < Tmax 4 Vout = 0 V 6 Tmin < Top < Tmax 4 dB dB 5 4 Vout = 1.8 V dB mV 35 50 mV 12 mA No load, Vout=VCC/2 10 25 Tmin < Top < Tmax 31 µA 33 µA AC performance Gain bandwidth product RL = 10 kΩ, CL = 100 pF, f = 100 kHz 340 kHz Fu Unity gain frequency RL = 10 kΩ, CL = 100 pF, 280 kHz φm Phase margin RL = 10 kΩ, CL = 100 pF 41 Degrees Gm Gain margin RL = 10 kΩ, CL = 100 pF 8 dB SR Slew rate RL = 10 kΩ, CL = 100 pF, Av=1 0.155 V/μs GBP 275 0.1 1. Guaranteed by design. Doc ID 15689 Rev 2 5/25 Electrical characteristics Table 4. TSV62x Shutdown characteristics VCC = 1.8 V (TSV623, TSV625) Symbol Parameter Conditions Min. Typ. Max. Unit 2.5 50 nA Tmin < Top < 85° C 200 nA Tmin < Top < 125° C 1.5 µA DC performance SHDN = VCCICC Supply current in shutdown mode (all operators) ton Amplifier turn-on time RL = 5 k, Vout = VCC- to VCC- + 0.2 V 200 ns toff Amplifier turn-off time RL = 2 k, Vout = VCC+ - 0.5 V to VCC+ - 0.7 V 20 ns VIH SHDN logic high VIL SHDN logic low IIH SHDN current high SHDN = VCC+ 10 pA IIL SHDN current low SHDN = VCC- 10 pA Output leakage in shutdown mode SHDN = VCC- 50 pA Tmin < Top < 125° C 1 nA IOLeak 6/25 1.35 V 0.6 Doc ID 15689 Rev 2 V TSV62x Table 5. Electrical characteristics VCC+ = +3.3 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, RL connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit DC performance Vio DVio TSV62x TSV62xA TSV623AIST - MiniSO10 4 0.8 1 TSV62x -Tmin < Top < Tmax TSV62xA - Tmin < Top < Tmax TSV623AIST - Tmin < Top < Tmax 6 2 2.2 Offset voltage mV Input offset voltage drift Input offset current Iio Iib CMR Tmin < Top < Tmax 1 10(1) pA 1 100 pA 1 10(1) pA 1 100 pA Input bias current Tmin < Top < Tmax Common mode rejection ratio 20 log (ΔVic/ΔVio) 0 V to 3.3 V, Vout = 1.65 V 57 Tmin < Top < Tmax 53 RL=10 kΩ, Vout= 0.5 V to 2.8 V 81 Tmin < Top < Tmax 76 35 50 Avd Large signal voltage gain VOH High level output voltage RL = 10 kΩ Tmin < Top < Tmax VOL Low level output voltage RL = 10 kΩ Tmin < Top < Tmax Isink Iout Isource ICC μV/°C 2 Supply current (per operator) 79 dB 98 23 Tmin < Top < Tmax 20 Vo = 0 V 23 Tmin < Top < Tmax 20 dB dB 5 4 Vo = 5 V dB mV 35 50 mV 45 mA 38 mA No load, Vout= 2.5 V 26 Tmin < Top < Tmax 33 µA 35 µA AC performance GBP Gain bandwidth product RL = 10 kΩ, CL = 100 pF, f = 100 kHz Fu Unity gain frequency φm 310 380 kHz RL = 10 kΩ, CL = 100 pF 310 kHz Phase margin RL = 10 kΩ, CL = 100 pF 41 Degrees Gm Gain margin RL = 10 kΩ, CL = 100 pF 8 dB SR Slew rate RL = 10 kΩ, CL = 100 pF, AV = 1 0.175 V/μs 0.11 1. Guaranteed by design. Doc ID 15689 Rev 2 7/25 Electrical characteristics Table 6. TSV62x VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, RL connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit DC performance Vio DVio Iio Iib CMR TSV62x TSV62xA TSV623AIST - MiniSO10 4 0.8 1 TSV62x - Tmin < Top < Tmax TSV62xA - Tmin < Top < Tmax TSV62xA - Tmin < Top < Tmax 6 2 2.2 Offset voltage mV Input offset voltage drift Tmin < Top < Tmax pA 1 100 pA 1 10(1) pA 1 100 pA Input bias current Tmin < Top < Tmax Common mode rejection ratio 20 log (ΔVic/ΔVio) 0 V to 5 V, Vout = 2.5 V 60 Tmin < Top < Tmax 55 RL=10 kΩ, Vout = 0.5 V to 4.5 V 85 Large signal voltage gain Tmin < Top < Tmax 80 Supply voltage rejection ratio VCC = 1.8 to 5 V 20 log (ΔVCC/ΔVio) Tmin < Top < Tmax 75 SVR 80 dB 98 dB 102 dB 73 VRF = 100 mVrms, f = 400 MHz 61 EMI rejection ratio VRF = 100 mVrms, f = 900 MHz 85 EMIRR = -20 log (VRFpeak/ΔVio) VRF = 100 mVrms, f = 1800 MHz 92 VRF = 100 mVrms, f = 2400 MHz 83 VOH High level output voltage VOL Low level output voltage dB RL = 10 kΩ 35 Tmin < Top < Tmax 50 7 mV RL = 10 kΩ 6 Iout Isource Supply current (per operator) 35 mV Tmin < Top < Tmax Isink ICC 1 10(1) Input offset current Avd EMIRR μV/°C 2 50 Vo = 5 V 40 Tmin < Top < Tmax 35 Vo = 0 V 40 Tmin < Top < Tmax 35 69 mA 74 mA No load, Vout = 2.5 V 29 Tmin < Top < Tmax 36 µA 38 µA AC performance GBP Fu 8/25 Gain bandwidth product RL = 10 kΩ, CL = 100 pF, f = 100 kHz Unity gain frequency RL = 10 kΩ, CL = 100 pF Doc ID 15689 Rev 2 350 420 kHz 360 kHz TSV62x Table 6. Electrical characteristics VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, RL connected to VCC/2 (unless otherwise specified) (continued) Symbol Parameter Conditions Min. Typ. Max. Unit φm Phase margin RL = 10 kΩ, CL = 100 pF 40 Degrees Gm Gain margin RL = 10 kΩ, CL = 100 pF 8 dB SR Slew rate RL = 10 kΩ, CL = 100 pF, AV = 1 0.19 V/μs en Equivalent input noise voltage f = 1 kHz 77 nV -----------Hz Total harmonic distortion + noise Av = 1, f = 1 kHz, RL= 100 kΩ, Vicm = Vcc/2, Vout = 2 Vpp 0.002 % THD+en 0.12 1. Guaranteed by design. Table 7. Shutdown characteristics at VCC = 5 V (TSV623, TSV625) Symbol Parameter Conditions Min. Typ. Max. Unit 5 50 nA Tmin < Top < 85° C 200 nA Tmin < Top < 125° C 1.5 µA DC performance SHDN = VIL ICC Supply current in shutdown mode (all operators) ton Amplifier turn-on time RL = 5 kΩ, Vout = VCC- to VCC- + 0.2 V 200 ns toff Amplifier turn-off time RL = 5 kΩ, Vout = VCC+ - 0.5 V to VCC + - 0.7 V 20 ns VIH SHDN logic high VIL SHDN logic low IIH SHDN current high SHDN = VCC+ 10 pA IIL SHDN current low SHDN = VCC- 10 pA 50 pA 1 nA IOLeak 2 V 0.8 Output leakage in shutdown SHDN = VCCmode Tmin < Top < 125° C Doc ID 15689 Rev 2 V 9/25 Electrical characteristics TSV62x Figure 2. Supply current vs. supply voltage at Vicm = VCC/2 Figure 4. Output current vs. output voltage at Figure 5. VCC = 5 V Figure 3. Output current vs. output voltage at VCC = 1.5 V Voltage gain and phase vs. frequency at Vcc = 1.5 V Ω Figure 6. Voltage gain and phase vs. frequency at VCC = 5 V Figure 7. Ω 10/25 Doc ID 15689 Rev 2 Phase margin vs. output current at VCC = 1.5 V and VCC = 5 V TSV62x Figure 8. Electrical characteristics Positive slew rate vs. time Figure 9. Figure 10. Positive slew rate vs. supply voltage Negative slew rate vs. time Figure 11. Negative slew rate vs. supply voltage Ω Figure 13. Distortion + noise vs. frequency 1 Vcc=1.5V Rl=10kΩ Vicm=2.5V THD + N (%) Input equivalent noise density (nV/VHz) Figure 12. Noise vs. frequency Vicm=4.5V Vcc=1.5V Rl=100kΩ 0.1 0.01 Ω Ω Vcc=5V T=25 C Frequency (Hz) 1E-3 10 Doc ID 15689 Rev 2 100 1000 10000 100000 11/25 Electrical characteristics TSV62x Figure 14. Distortion + noise vs. output voltage Figure 15. EMIRR vs. frequency at VCC = 5 V, T = 25° C 120 Vcc=5.5V Rl=10kohms Vcc=5.5V Rl=100kohms Output Voltage (Vpp) 12/25 f=1kHz Gain=1 BW=22kHz Vicm=Vcc/2 100 EMIRR Vpeak (dB) THD + N (%) Vcc=1.5V Rl=10kohms Vcc=1.5V Rl=100kohms 80 60 40 20 0 1 10 Doc ID 15689 Rev 2 2 10 3 10 TSV62x Application information 4 Application information 4.1 Operating voltages The TSV62x can operate from 1.5 to 5.5 V. Their parameters are fully specified for 1.8-, 3.3and 5-V power supplies. However, the parameters are very stable in the full VCC range and several characterization curves show the TSV62x characteristics at 1.5 V. Additionally, the main specifications are guaranteed in extended temperature ranges from -40° C to +125° C. 4.2 Rail-to-rail input The TSV62x are built with two complementary PMOS and NMOS input differential pairs. The devices have a rail-to-rail input, and the input common mode range is extended from VCC- - 0.1 V to VCC+ + 0.1 V. The transition between the two pairs appears at VCC+ - 0.7 V. In the transition region, the performance of CMRR, PSRR, Vio (Figure 16 and Figure 17) and THD is slightly degraded. Figure 16. Input offset voltage vs input common mode at VCC = 1.5 V Figure 17. Input offset voltage vs input common mode at VCC = 5 V The devices are guaranteed without phase reversal. 4.3 Rail-to-rail output The operational amplifier’s output level can go close to the rails: 35 mV maximum above and below the rail when connected to a 10 kΩ resistive load to VCC/2. Doc ID 15689 Rev 2 13/25 Application information 4.4 TSV62x Optimization of DC and AC parameters These devices use an innovative approach to reduce the spread of the main DC and AC parameters. An internal adjustment achieves a very narrow spread of current consumption (29 µA typical, min/max at ±17%). Parameters linked to the current consumption value, such as GBP, SR and AVd benefit from this narrow dispersion. All parts present a similar speed and the same behavior in terms of stability. In addition, the minimum values of GBP and SR are guaranteed (GBP = 350 kHz min, SR = 0.12 V/µs min). 4.5 Shutdown function (TSV623, TSV625) The operational amplifier is enabled when the SHDN pin is pulled high. To disable the amplifier, the SHDN must be pulled down to VCC-. When in shutdown mode, the amplifier output is in a high impedance state. The SHDN pin must never be left floating but tied to VCC+ or VCC-. The turn-on and turn-off times are calculated for an output variation of ±200 mV (Figure 18 and Figure 19 show the test configurations). +Vcc +Vcc GND + DUT - 2KO Vcc-0.5V Figure 19. Test configuration for turn-off time (Vout pulled down) Vcc-0.5V GND + DUT - GND 2KO Figure 18. Test configuration for turn-on time (Vout pulled down) GND Figure 20. Turn-on time, VCC = 5 V, Vout pulled down, T = 25° C Figure 21. Turn-off time, VCC = 5 V, Vout pulled down, T = 25° C Shutdown pulse Voltage (V) Vout Output voltage (V) Vcc = 5V T = 25°C Vout Vcc = 5V T = 25 C RL connected to GND Time( s) 14/25 Shutdown pulse Time( s) Doc ID 15689 Rev 2 TSV62x 4.6 Application information Driving resistive and capacitive loads These products are micro-power, low-voltage operational amplifiers optimized to drive rather large resistive loads, above 5 kΩ. For lower resistive loads, the THD level may significantly increase. In a follower configuration, these operational amplifiers can drive capacitive loads up to 100 pF with no oscillations. When driving larger capacitive loads, adding a small resistor in series at the output can improve the stability of the device (see Figure 22 for recommended in-series resistor values). Once the value of the in-series resistor has been selected, the stability of the circuit should be tested on bench and simulated with the simulation model. Figure 22. In-series resistor vs. capacitive load 4.7 PCB layouts For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible to the power supply pins. 4.8 Macromodel Two accurate macromodels (with or without shutdown feature) of TSV62x are available on STMicroelectronics’ web site at www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the TSV62x operational amplifiers. It emulates the nominal performances of a typical device within the specified operating conditions mentioned in the datasheet. It helps to validate a design approach and to select the right operational amplifier, but it does not replace on-board measurements. Doc ID 15689 Rev 2 15/25 Package information 5 TSV62x Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 16/25 Doc ID 15689 Rev 2 TSV62x 5.1 Package information SOT23-8 package information Figure 23. SOT23-8 package mechanical drawing Table 8. SOT23-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 1.45 0.057 A1 0.15 0.006 A2 0.90 1.30 0.035 0.051 b 0.22 0.38 0.009 0.015 c 0.08 0.22 0.003 0.009 D 2.80 3 0.110 0.118 E 2.60 3 0.102 0.118 E1 1.50 1.75 0.059 0.069 e 0.65 0.026 e1 1.95 0.077 L 0.30 0.60 < 0° 8° Doc ID 15689 Rev 2 0.012 0.024 17/25 Package information 5.2 TSV62x SO-8 package information Figure 24. SO-8 package mechanical drawing Table 9. SO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.75 0.25 Max. 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k ccc 18/25 Inches 1.04 0 0.040 8° 0.10 Doc ID 15689 Rev 2 1° 8° 0.004 TSV62x 5.3 Package information MiniSO-8 package information Figure 25. MiniSO-8 package mechanical drawing Table 10. MiniSO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.1 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.026 0.80 0.016 0.024 L1 0.95 0.037 L2 0.25 0.010 k ccc 0° 0.037 8° 0.10 Doc ID 15689 Rev 2 0° 0.031 8° 0.004 19/25 Package information 5.4 TSV62x MiniSO-10 package information Figure 26. MiniSO-10 package mechanical drawing Table 11. MiniSO-10 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.10 Max. 0.043 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.78 0.86 0.94 0.031 0.034 0.037 b 0.25 0.33 0.40 0.010 0.013 0.016 c 0.15 0.23 0.30 0.006 0.009 0.012 D 2.90 3.00 3.10 0.114 0.118 0.122 E 4.75 4.90 5.05 0.187 0.193 0.199 E1 2.90 3.00 3.10 0.114 0.118 0.122 e L 0.50 0.40 L1 k aaa 20/25 Inches 0.55 0.020 0.70 0.016 0.95 0° 3° 0.022 0.028 0.037 6° 0.10 Doc ID 15689 Rev 2 0° 3° 6° 0.004 TSV62x 5.5 Package information TSSOP14 package information Figure 27. TSSOP14 package mechanical drawing Table 12. TSSOP14 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.176 e L 0.65 0.45 L1 k aaa 1.00 0.60 0.0256 0.75 0.018 1.00 0° 0.024 0.030 0.039 8° 0.10 Doc ID 15689 Rev 2 0° 8° 0.004 21/25 Package information 5.6 TSV62x TSSOP16 package information Figure 28. TSSOP16 package mechanical drawing b Table 13. TSSOP16 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 1.05 0.031 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.008 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.177 e 0° L 0.45 aaa 1.00 0.65 k L1 22/25 Inches 0.60 0.006 0.039 0.041 0.0256 8° 0° 0.75 0.018 1.00 8° 0.024 0.030 0.039 0.10 Doc ID 15689 Rev 2 0.004 TSV62x 6 Ordering information Ordering information Table 14. Order codes Part number Temperature range Package Packing SO-8 Tube and tape & reel TSV622ID/DT TSV622 TSV622AID/DT TSV622A TSV622IST K107 MiniSO-8 Tape & reel TSV622AIST K143 TSV622ILT TSV623IST Marking SOT23-8 Tape & reel MiniSO-10 Tape & reel -40° C to +125° C K107 K114 TSV623AIST K144 TSV624IPT TSV624 TSSOP-14 Tape & reel TSV624AIPT TSV624A TSV625IPT TSV625 TSSOP-14 TSV625AIPT Tape & reel TSV625A Doc ID 15689 Rev 2 23/25 Revision history 7 TSV62x Revision history Table 15. 24/25 Document revision history Date Revision Changes 25-May-2009 1 Initial release. 15-Jun-2009 2 Corrected pin connection diagram in Figure 1. Doc ID 15689 Rev 2 TSV62x Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 15689 Rev 2 25/25