View the Part Number Specific Data Sheet for full specifications

ECLIPTEK
PART NUMBER DATA SHEET
CORPORATION
EC2700TTS-47.000M
REGULATORY COMPLIANCE
R
(Data Sheet downloaded on Jun 28, 2016)
2011/65 +
2015/863
168 SVHC
ITEM DESCRIPTION
Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 2.5Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD)
47.000MHz ±100ppm -10°C to +70°C
ELECTRICAL SPECIFICATIONS
Nominal Frequency
47.000MHz
Frequency Tolerance/Stability
±100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating
Temperature Range, Supply Voltage Change, Ouput Load Change, First Year Aging at 25°C, Shock, and Vibration)
Aging at 25°C
±5ppm/year Maximum
Operating Temperature Range
-10°C to +70°C
Supply Voltage
2.5Vdc ±5%
Input Current
6mA Maximum
Output Voltage Logic High (Voh)
90% of Vdd Minimum (IOH = -4mA)
Output Voltage Logic Low (Vol)
10% of Vdd Maximum (IOL = +4mA)
Rise/Fall Time
4nSec Maximum (Measured at 20% to 80% of waveform)
Duty Cycle
50 ±5(%) (Measured at 50% of waveform)
Load Drive Capability
15pF Maximum
Output Logic Type
CMOS
Pin 1 Connection
Tri-State (High Impedance)
Output Control Input Voltage Logic
High (Vih)
90% of Vdd Minimum or No Connect to Enable Output
Output Control Input Voltage Logic
Low (Vil)
10% of Vdd Maximum to Disable Output (High Impedance)
Standby Current
10µA Maximum (Disabled Output, High Impedance)
RMS Phase Jitter
1pSec Maximum (12kHz to 20MHz offset frequency)
Start Up Time
10mSec Maximum
Storage Temperature Range
-55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
Fine Leak Test
MIL-STD-883, Method 1014, Condition A
Flammability
UL94-V0
Gross Leak Test
MIL-STD-883, Method 1014, Condition C
Mechanical Shock
MIL-STD-883, Method 2002, Condition B
Moisture Resistance
MIL-STD-883, Method 1004
Moisture Sensitivity
J-STD-020, MSL 1
Resistance to Soldering Heat
MIL-STD-202, Method 210, Condition K
Resistance to Solvents
MIL-STD-202, Method 215
Solderability
MIL-STD-883, Method 2003
Temperature Cycling
MIL-STD-883, Method 1010, Condition B
Vibration
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 1 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200
ECLIPTEK
PART NUMBER DATA SHEET
R
CORPORATION
EC2700TTS-47.000M
MECHANICAL DIMENSIONS (all dimensions in millimeters)
5.00
±0.15
1.80
MAX
2
MARKING
ORIENTATION
7.00
±0.15
1.20 ±0.20 (X4)
3
CONNECTION
1
Tri-State
2
Case/Ground
3
Output
4
Supply Voltage
LINE MARKING
5.08
±0.15
1
2.60 ±0.15
PIN
4
1.40
±0.10 (X4)
1
ECLIPTEK
2
47.000M
3
XXXXX
XXXXX=Ecliptek
Manufacturing Identifier
Suggested Solder Pad Layout
All Dimensions in Millimeters
2.0 (X4)
2.2 (X4)
Solder Land
(X4)
2.88
1.81
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 2 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200
ECLIPTEK
PART NUMBER DATA SHEET
R
CORPORATION
EC2700TTS-47.000M
CLOCK OUTPUT
TRI-STATE INPUT
OUTPUT WAVEFORM & TIMING DIAGRAM
VIH
VIL
VOH
80% of Waveform
OUTPUT DISABLE
(HIGH IMPEDANCE
STATE)
50% of Waveform
20% of Waveform
VOL
tPLZ
Fall
Time
Rise
Time
tPZL
TW
T
Duty Cycle (%) = TW/T x 100
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 3 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200
ECLIPTEK
PART NUMBER DATA SHEET
R
CORPORATION
EC2700TTS-47.000M
Test Circuit for CMOS Output
Frequency
Counter
Oscilloscope
+
+
Power
Supply
_
Current
Meter
_
Supply
Voltage
(VDD)
Probe
(Note 2)
Output
+
Voltage
Meter
_
0.01µF
(Note 1)
0.1µF
(Note 1)
Ground
CL
(Note 3)
No Connect
or Tri-State
Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency
ceramic bypass capacitor close to the package ground and VDD pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth
(>300MHz) passive probe is recommended.
Note 3: Capacitance value CL includes sum of all probe and fixture capacitance.
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 4 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200
ECLIPTEK
PART NUMBER DATA SHEET
R
CORPORATION
EC2700TTS-47.000M
Recommended Solder Reflow Methods
High Temperature Infrared/Convection
TS MAX to TL (Ramp-up Rate)
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
Ramp-up Rate (TL to TP)
Time Maintained Above:
- Temperature (TL)
- Time (tL)
Peak Temperature (TP)
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
Additional Notes
3°C/Second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/Second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 Seconds
6°C/Second Maximum
8 Minutes Maximum
Level 1
Temperatures shown are applied to body of device.
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 5 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200
ECLIPTEK
PART NUMBER DATA SHEET
R
CORPORATION
EC2700TTS-47.000M
Recommended Solder Reflow Methods
Low Temperature Infrared/Convection 240°C
TS MAX to TL (Ramp-up Rate)
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
Ramp-up Rate (TL to TP)
Time Maintained Above:
- Temperature (TL)
- Time (tL)
Peak Temperature (TP)
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
Additional Notes
5°C/Second Maximum
N/A
150°C
N/A
60 - 120 Seconds
5°C/Second Maximum
150°C
200 Seconds Maximum
240°C Maximum
240°C Maximum 2 Times / 230°C Maximum 1 Time
10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time
5°C/Second Maximum
N/A
Level 1
Temperatures shown are applied to body of device.
Low Temperature Manual Soldering
185°C Maximum for 10 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
High Temperature Manual Soldering
260°C Maximum for 5 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
www.ecliptek.com | Specification Subject to Change Without Notice | Revision O 06/01/2015 | Page 6 of 6
Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626
1-800-ECLIPTEK or 714.433.1200