Contents Passive distributors 2001350000 – 2015/2016 Passive distributors Passive distributors Introduction G.2 M12 distributors G.4 ECO modules G.16 M12 Push-Pull G.18 M12 IDC G.26 M12 VA stainless steel G.30 M12 metal distributors G.32 M12 distributors 1:1 Passive G.38 M12 Combi distributor G.39 M12 distributor for NPN and PNP sensors G.40 M12 wall bushing G.41 Solutions to customer specification G.44 M12 distributors accessories G.45 M8 distributors G.46 M5 distributors G.56 M12 Ex i distributors G.60 G G.1 Passive distributors Introduction SAI Passive SAI Passive products are built with premium materials using the highest quality production methods. The fully encapsulated distributors are designed to meet harsh industrial requirements. Naturally they have also been designed so that they are easy to handle. The self assembled connectors in the hooded version, for example, are joined into a single part so that the entire block is available for the connection. This is a unique solution for distributors that has no equal anywhere. Nothing can break off, get mixed up or wired up incorrectly. The distributors are equipped by default with threaded metal rings. This ensures a very reliable screw-on connection. The nut is completely threaded without any interruptions. This eliminates the possibility of it getting stuck or jammed. The IDC versions are especially noteworthy. Sensor cables of the proper lengths can be connected directly here. G G.2 2001350000 – 2015/2016 Passive distributors Introduction Compact The connection block is a single piece. Small Extremely small M12 distributor Fast G Insulation displacement connection can be used to directly connect the sensor cables Robust Threaded metal ring without cut outs for reliable, safe handling M12 distributor standard M12 distributor with DIP switch coding M12 distributor with stainless steel housing M12 distributor for Zone 1 2001350000 – 2015/2016 G.3 Passive distributors M12 distributors SAI distributor with plug in connection hood: SAI-M • Integrated plug in connector in connection hood • M12 robust metal thread for sensor/actuator connection, now also available with plastic thread as an alternative • Quick replacement of bus cables • Bus cable can be supplied pre-assembled • Two connection systems for bus cable: screw or tension clamp • Very flat connection hood: no higher than smallest 90° M12 round plug • Distributor and connection hood can be supplied separately • Connection hood compatible with 4 and 8 channel SAI distributors (upgrades only entail changing the base module) • IP 68 Ingress protection class (IDC IP 67), • Housing made from Pocan® (PBT): – high dimensional stability – good electrical and mechanical properties – flame retardant without dioxin or furan formers – resistant to coolants and lubricants • UL/CSA approvals for M12 SAI distributor • SAI distributor available in pollution severity class 3 • Cable exit on top • Weidmüller SAI distributors have the largest storage capacity in the connection hood • Female connectors integrated into the metal plate for fast and reliable connections • Wide range of M8 and M12 cables and plug-in connectors • Various cable lengths available • Metal hoods and housings also available • Plug-in connection module for bus cables increases flexibility on site • Integral, plug in electrical isolation for two separate electric circuits (e.g. for emergency stop) • Simple and vibration resistant connections on site • Captive metric screws (grade 8.8 steel) have a +/- head • M12 and IDC connections • 1:1 arrangement available G G.4 2001350000 – 2015/2016 M12 distributors Passive distributors Overview of M12 Distributors Fixed cable version • Pre-assembled bus cable minimises installation time and reduces wiring errors • Cable carrier compatible versions are available with polyurethane (PUR) sheathing M12 Push-Pull quick-fit connection system M12 Push-Pull is the new connection system for sensors and actuators. It is downward compatible to the existing M12 system, which means that both old M12 and new M12 Push-Pull lines can be used together on these SAIs. M12 Push-Pull decreases installation time and increases installation safety by means of colour coding and provides an audible click on locking for added reassurance. G SAI ECO – the cost-effective alternative Weidmüller SAI distributors with hood have long since been standard fittings in machines and installations. Why plastic threaded rings? There are some applications, however, that call for a further version. In some applications it is necessary to avoid all metal parts, unless these are made from stainless steel. In such cases stainless steel is then used for screws and nuts only, but the M12 threaded rings can be made from plastic. Such modules can now be supplied on request. The use of plastic rings results in a cheaper alternative. Although the service life and resistance are reduced when compared to metal, this is acceptable for some applications. 2001350000 – 2015/2016 G.5 Passive distributors M12 distributors Overview of SAI M12 Plastic 4-way, 4-pole 4-way, 5-pole 6-way, 4-pole 6-way, 5-pole 8-way, 4-pole 8-way, 5-pole M12 Metal 4-way, 4-pole 4-way, 5-pole 8-way, 4-pole 8-way, 5-pole M12 Line 4-way, 4-pole 4-way, 5-pole 6-way, 4-pole G M8 Line 4-way, 3-pole 4-way, 4-pole 6-way, 3-pole 6-way, 4-pole 8-way, 3-pole 8-way, 4-pole 10-way, 3-pole 12-way, 3-pole G.6 Hood 1705920000 1701230000 1705930000 1701240000 1705940000 1701250000 M23 9456000000 9456000001 9456010000 9456010001 9456020000 1795470000 5m 9456190000 9456330000 9456470000 9456610000 9456750000 9456890000 10 m 9456200000 9456340000 9456480000 9456620000 9456760000 9456900000 Hood without shield connection Hood with shield connection 1783540000 1783520000 1783530000 1783510000 5m 10 m 9456190002 9456200002 9456750002 9456760002 M12 group outlet 5m 10 m 1267330000 1070650000 1070630000 1265920000 1070660000 1070640000 1265930000 5m 10 m 1828720000 1849680000 1828700000 1849700000 1828680000 1828620000 1828660000 1828640000 1828710000 1849690000 1828690000 1849670000 1828670000 1828610000 1828650000 1828630000 1783500000 1783490000 1265940000 M12 group outlet 1828740000 1828730000 1871680000 1877950000 Solder version for PCB 1057720000 15 m 9456210000 9456350000 9456490000 9456630000 9456770000 9456910000 20 m 9456230000 9456370000 9456510000 9456650000 9456790000 9456930000 2001350000 – 2015/2016 M12 distributors 6$,0 6$,0 6$,0 Screw connection Screw connection Tension-clamp connection Tension clamp connection Empty Complete modules, NPN-switched Note 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 10...30 V 2A 4A 10 A 3 IP 68 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.08...1.5 mm² SAI-4 M 4P M12 UT SAI-6-M 4P M12 UT SAI-8-M 4P M12 UT SAI-4/6/8-MH BL3.5 SAI-4/6/8-MH BL3.5 SV SAI-4/6/8-MH BLZF3.5 SAI-4/6/8-MH BLZF3.5 SV 2 2 2 1705921000 1705931000 1705941000 SAI-4-M 5P M12 UT SAI-6-M 5P M12 UT SAI-8-M 5P M12 UT SAI-4-M 5P M12 OL UT SAI-8-M 5P M12 OL UT 1 50 1 50 1724750000 1724750050 1752080000 1752080050 SAI-4/6/8-MH BL3.5 SAI-4/6/8-MH BL3.5 SV SAI-4/6/8-MH BLZF3.5 SAI-4/6/8-MH BLZF3.5 SV SAI-4/6/8-MH LEER SAI-8-M 5P M12 NPN Other versions on request Other versions on request Wiring diagram Wiring diagram blue red blue 5-pole QTY 1 1 1 1 1 1 1 1 Order No. 1701230000 1701240000 1701250000 1800000000 1740190000 1816610000 1854000000 1767880000 2 2 2 2 2 1701231000 1701241000 1701251000 1800001000 1740191000 1 50 1 50 1 1724750000 1724750050 1752080000 1752080050 1783460000 1 1781060000 G red 6-way Without initiator-LED, for analogue signals Without initiator-LED, for analogue signals Mounting hood 4-channel 6-channel 8-channel 4-channel 8-channel Type SAI-4-M 5P M12 SAI-6-M 5P M12 SAI-8-M 5P M12 SAI-4-M 5P M12 OL SAI-8-M 5P M12 OL SAI-8-M 5P M12 OL2 SAI-4-M 5P M12 ZF SAI-8-M 5P M12 ZF III 8-way Without initiator-LED, for analogue signals Tension-clamp connection Tension-clamp connection Base unit SAI-4/6/8-M Order No. 1705920000 1705930000 1705940000 4-way Without initiator-LED, for analogue signals 4-pole QTY 1 1 1 6-way 4-channel 6-channel 8-channel 4-channel 8-channel 8-channel 4-channel 8-channel Type SAI-4-M 4P M12 SAI-6-M 4P M12 SAI-8-M 4P M12 8-way Complete modules 4-way SAI-4/6/8-M Ordering data Passive distributors Hood version With dual power supply: 2x8 = 16A total current Clamping range up to 2.5 mm² with screw connection 2001350000 – 2015/2016 G.7 M12 distributors 6$,) 6$,) 6$,) Passive distributors Fixed cable version SAI-4/6/8-F 8-channel with reinforced fixed cable* Note Cable length 3 m Cable length 5 m Cable length 10 m Cable length 15 m Cable length 20 m SAI-6-F 4P PUR 3M SAI-6-F 4P PUR 5M SAI-6-F 4P PUR 10M SAI-6-F 4P PUR 15M SAI-6-F 4P PUR 20M 1 1 1 1 1 Cable length 3 m Cable length 5 m Cable length 10 m Cable length 15 m Cable length 20 m SAI-8-F 4P PUR 3M SAI-8-F 4P PUR 5M SAI-8-F 4P PUR 10M SAI-8-F 4P PUR 15M SAI-8-F 4P PUR 20M 1 1 1 1 1 Cable length 2 m Cable length 5 m Cable length 10 m Cable length 15 m Cable length 20 m Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 10...30 V 2A 4A 9A 3 IP 68 -20...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes QTY 1 1 1 1 1 Order No. 9456320000 9456330000 9456340000 9456350000 9456370000 9456460000 9456470000 9456480000 9456490000 9456510000 SAI-6-F 5P PUR 3M SAI-6-F 5P PUR 5M SAI-6-F 5P PUR 10M SAI-6-F 5P PUR 15M SAI-6-F 5P PUR 20M 1 1 1 1 1 9456600000 9456610000 9456620000 9456630000 9456650000 9456740000 9456750000 9456760000 9456770000 9456790000 SAI-8-F 5P PUR 3M SAI-8-F 5P PUR 5M SAI-8-F 5P PUR 10M SAI-8-F 5P PUR 15M SAI-8-F 5P PUR 20M 1 1 1 1 1 9456880000 9456890000 9456900000 9456910000 9456930000 SAI-8-F 5P 2M 0.5/1.0U SAI-8-F 5P 5M 0.5/1.0U SAI-8-F 5P 10M 0.5/1.0U SAI-8-F 5P 15M 0.5/1.0U SAI-8-F 5P 20M 0.5/1.0U 1 1 1 1 1 7915030000 9457590000 9457600000 1784510000 1784500000 Other versions on request Other versions on request Wiring diagram Wiring diagram green-yellow green-yellow brown brown blue blue white white grey-pink green green red-blue yellow yellow white-green grey grey brown-green pink pink red white-yellow red yellow-brown white-grey 8-way violet G.8 5-pole Type SAI-4-F 5P PUR 3M SAI-4-F 5P PUR 5M SAI-4-F 5P PUR 10M SAI-4-F 5P PUR 15M SAI-4-F 5P PUR 20M black * 3x1mm² und 16x0.5mm² total current 12A SAI-4/6/8-F 4-way 8-channel Order No. 9456180000 9456190000 9456200000 9456210000 9456230000 6-way G Cable length 3 m Cable length 5 m Cable length 10 m Cable length 15 m Cable length 20 m QTY 1 1 1 1 1 4-way 6-channel 4-pole Type SAI-4-F 4P PUR 3M SAI-4-F 4P PUR 5M SAI-4-F 4P PUR 10M SAI-4-F 4P PUR 15M SAI-4-F 4P PUR 20M 6-way 4-channel grey-brown black violet 8-way Ordering data 2001350000 – 2015/2016 M12 distributors Fixed cable version Thin design SAI-4-F M12 L Passive distributors SAI-4-F M12 L Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 2001350000 – 2015/2016 Other versions on request QTY 1 1 Order No. 1070650000 1070660000 R4 .2 20 Other versions on request 120.5 137 144 Type SAI-4-F 5P M12 L 5M SAI-4-F 5P M12 L 10M 17 20.9 9 G 5-pole QTY 1 1 Order No. 1070630000 1070640000 Dimensioned drawing Dimensioned drawing 10...30 V 2A 3A 9A 3 IP 68 -20...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes 3.5 3x26=78 120.5 4-pole 24 green-yellow green-yellow brown brown blue blue white white green green yellow yellow grey grey 4-way Technical data Type SAI-4-F 4P M12 L 5M SAI-4-F 4P M12 L 10M 17 20.9 9 4-way Note 3.5 137 144 48 3.5 20 3.5 48 3x26=78 SAI-4-F M12 L Cable length 5 m Cable length 10 m .5 4-channel 12.5 Ø4 .2 Ø4 24 Ordering data 3.2 17 .5 R4 .2 12.5 Ø4 .2 Ø4 3.2 17 G.9 Fixed cable version Thin design 20 SAI-6-F M12 L 17 10.3 G 13.8 17 20.9 24 SAI-6-F M12 L Ordering data 4-channel Note Cable length 5 m Cable length 10 m Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-6-F 4P M12 L 5M SAI-6-F 4P M12 L 10M QTY 1 1 4-pole Order No. 1265920000 1265930000 Dimensioned drawing 10...30 V 2A 3A 9A 3 IP 68 -20...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes LED_ ye rd 4.7k 3 pk 4.7k 3 4.7k 3 ye 4.7k 3 gn 4.7k 3 4.7k 3 br (+) (PE) gn/ye 1 sock4 1 sock3 1 sock2 4 5 2 bl (-) sock5 4 5 2 LED_ ye 1 4 5 2 LED_ ye sock6 4 5 2 LED_ ye 1 4 5 2 LED_ ye gr 4 5 2 LED_ ye wh G.10 196 172.5 189 26 ±0.1 48 3.5 Passive distributors M12 distributors 1 sock1 3.3k LED_ gn 2001350000 – 2015/2016 M12 distributors Line SAI-6-S Passive distributors SAI-4-S 132 139 10.3 132 26 ±0.1 43 14.5 3.5 17 26 14.8 5 13.8 17 20.9 SAI-4-S Ordering data 3-pole Note 4-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-4-S8 4P M12 L QTY 1 6 24 M12 Order No. 1267330000 Type SAI-6-S12 4P M12 L QTY 1 LED_ ye 4.7k 4.7k 3 4.7k 3 3 1 4.7k sock 3 1 sock 2 {a} 1 sock 1 4 3 2 1 (-) 6. 7 (+) 5 4.7k 4.7k 4 5 2 3 3 sock 4 1 sock 3 4 5 2 3 1 4 5 2 LED_ ye 1 sock 2 4 5 2 1 sock 1 3.3k LED_ gn (PE) 8 M12/8p M12/8p 8 1 8 6 7 1 6 7 5 2 2001350000 – 2015/2016 3 LED_ ye LED_ gn (PE) 8 Order No. 1265940000 LED_ ye 4 5 2 3.3k 4.7k sock 4 4 5 2 3 1 4 5 2 LED_ ye 4.7k 4 5 2 LED_ ye {a} G LED_ ye LED_ ye 4 3 2 1 (-) 6. 7 (+) 5 M12 Dimensioned drawing Dimensioned drawing 10...30 V 1A 2A 6A 3 IP 67 ...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... 3 4 5 2 3 4 G.11 M12 distributors with M23 outlet 0 Passive distributors SAI-4/6/8-S Ordering data Complete modules Note 4-channel 6-channel 8-channel Type SAI-4-S 4P M12 SAI-6-S 4P M12 SAI-8-S 4P M12 QTY 1 1 1 Other versions on request 4-pole Order No. 9456000000 9456010000 9456020000 SAI-4/6/8-S Type SAI-4-S 5P M12 SAI-6-S 5P M12 SAI-8-S 5P M12 QTY 1 1 1 Other versions on request 5-pole Order No. 9456000001 9456010001 1795470000 G 10...30 V 2A 4A 10 A 3 IP 68 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... 12 PE 11 (+) 6 sock 8 8 sock 7 7 sock 6 6 sock 5 5 sock 4 4 sock 3 3 sock 2 2 1 sock 1 8 x ye gr gr G.12 8 9 10 11 17 7 16 19 18 12 15 1 5 14 13 4 3 2 SAI-6-S Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram Wiring diagram 10 (-) 9 (-) SAI-8-S Technical data 2001350000 – 2015/2016 M12 distributors with M16 outlet Passive distributors SAI-8-M16 0 6$,6 6$,6 6$,6 SAI-8-M16 Ordering data Complete modules Note 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 2001350000 – 2015/2016 Type SAI-8-M16 4P M12 4-pole QTY 1 Other versions on request G Order No. 1831020000 Dimensioned drawing 10...30 V 2A 4A 6A 3 IP 67 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... PE JL CM sock 1 F sock 2 G sock 3 H sock 4 B sock 5 K sock 6 A sock 7 D sock 8 E M G F E H D J K A B L C G.13 M12 distributors Hood version with DIP-switch coding Passive distributors SAI-8-M M12 DIP 6$,0 6$,0 6$,0 SAI-8-M M12 DIP Ordering data 8-channel Note 4-pole QTY 1 Order No. 1059430000 Other versions on request Technical data Dimensioned drawing 10...30 V 2A 4A 8A 3 IP 68 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.08...1.5 mm² (+) 15 6 10 8-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-8-M-4P M12 DIP 12 2 4 20 6-way Complete modules 3 18 11 21 4-way G 5 17 (+) 15 13 19 7 1 (–) 16 (+) 14 (PE) 8 9 G.14 2001350000 – 2015/2016 Passive distributors G 2001350000 – 2015/2016 G.15 Passive distributors ECO modules SAI ECO SAI ECO – the cost-effective alternative Cost-effective alternative The Weidmüller SAI distributors with hoods have long since been standard fittings in machines and installations. The ECO modules were initially developed to optimise costs. Many details of these modules were adapted in such a way that they can still be used wherever standard modules were used in the past, but the individual solutions have now become simpler: Why plastic threaded rings? There are some applications, however, that call for a further version. In some applications it is necessary to avoid all metal parts. In such cases stainless steel is then used for screws and nuts only, but the M12 threaded rings can be made from plastic. Such modules can now be supplied on request. G The use of plastic rings results in a cheaper alternative. Although the service life and resistance are reduced when compared to metal, this is acceptable for some applications. • M arkers: Markers clipped onto the module can no longer be printed with a identification system. It is easier to simply order the markers with the required printing from us. The markers in the proven MultiCard format are printed with our PrintJetPro Printer. • One way disconnector: Up until now it was usual to achieve electrical isolation devised by Weidmüller by way of jumpers. To reduce costs, these jumpers have been replaced by solder bridges. These are simply cut to provide electrical isolation. • No protective caps: Normally, Weidmüller M12 distributors are always supplied with two protective caps. These were not always required and so they have been omitted. • Standard cable gland: The vibration resistant black screw cable gland has been replaced by a standard IP 68 cable gland. These cost-cutting measures result in yet more applications for Weidmüller SAI distributors. Greater reliability than with comparable systems Plastic threaded rings are nothing new. However, the problem in the past was that the threaded rings formed part of the housing and were therefore made from the same plastic. Weidmüller has once again pioneered a new and better solution. Weidmüller plastic rings are manufactured separately, which means that a more suitable, more durable material can be chosen. The Weidmüller production method is also patented. Special threaded ring increases durability G.16 2001350000 – 2015/2016 ECO modules 6$,0 6$,0 6$,0 SAI-4/6/8-M Ordering data NPN NPN Base unit Mounting hood 4-channel 6-channel 8-channel 4-channel 8-channel Type SAI-4-M 5P M12 ECO SAI-6-M 5P M12 ECO SAI-8-M 5P M12 ECO SAI-4-M 5P M12 NPN ECO SAI-8-M 5P M12 NPN ECO 4-channel 6-channel 8-channel SAI-4-M 5P M12 ECO UT SAI-6-M 5P M12 ECO UT SAI-8-M 5P M12 ECO UT Screw connection Tension clamp connection Note SAI-4/6/8-MH BL3.5 SV SAI-4/6/8-MH BLZF3.5 SV Order No. 1892100000 1892090000 1892080000 1892100005 1892080005 2 2 2 1892101000 1892091000 1892081000 50 50 1724750050 1752080050 These distributors are supplied without protective caps and markers. Technical data Type QTY Order No. G Wiring diagram 10...30 V 2A 4A 10 A 3 IP 68 -20...90 °C Pocan PBT (UL 94 V0) CuZn Pocan grey, RAL 7032 V-0 0.08...1.5 mm² blue red 8-way 6-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 5-pole QTY 1 1 1 1 1 4-way Complete modules Passive distributors Hood version With dual power supply: 2x8 = 16A total current Clamping range up to 2.5 mm² with screw connection 2001350000 – 2015/2016 G.17 Passive distributors M12 Push-Pull M12 Push-Pull: SAI distributors and cables, with rapid-connection technology SAI distributors with M12 Push-Pull plug Whereas the standard M12 system requires the sleeves to be laboriously screwed on and that operation is hindered by the vibration guard, M12 Push-Pull works with one click, just like those well-known garden hose systems. The audible locking function guarantees a safe and reliable connection as well as a good seal. M12 Push-Pull is currently supplied by Weidmüller and five other international companies. M12 Push-Pull connections provide sufficient space for using T-pieces. The SAI module is slimmer and now only 54 mm wide. M12 Push-Pull M23 versions G The new SAI M12 Push-Pull distributors can be used with M12 plug-in connectors but also with the new M12 Push-Pull plug-in connectors. The SAI distributors are available in fixed cable, hood, bayonet connection and M23 versions. M12 Push-Pull speeds up installation and increases installation reliability thanks to the colour coding and the audible click when locking it into place. M12 Push-Pull hood version M12 Push-Pull with bayonet connection G.18 2001350000 – 2015/2016 M12 Push-Pull 4-channel SAI-4/8-F 8-channel Note 4-pole Cable length 2 m Cable length 5 m Cable length 10 m Type SAI-4-F 4P FC 2M SAI-4-F 4P FC 5M SAI-4-F 4P FC 10M QTY 1 1 1 Order No. 1848080000 1848060000 1848050000 Cable length 2 m Cable length 5 m Cable length 10 m SAI-8-F 4P FC 2M SAI-8-F 4P FC 5M SAI-8-F 4P FC 10M 1 1 1 1847990000 1848000000 1847980000 Other versions on request Ordering data Passive distributors Fixed cable version SAI-4/8-F 5-pole Type SAI-4-F 5P FC 2M SAI-4-F 5P FC 5M SAI-4-F 5P FC 10M QTY 1 1 1 Order No. 1847940000 1847950000 1847930000 SAI-8-F 5P FC 2M SAI-8-F 5P FC 5M SAI-8-F 5P FC 10M 1 1 1 1848020000 1848030000 1848010000 Other versions on request G LED_gn gn/ye br br bl LED_gn LED_ye sock 1 sock 1 wh LED_ye LED_ye LED_ye sock 2 sock 2 gn LED_ye LED_ye LED_ye sock 3 ye sock 3 LED_ye LED_ye LED_ye sock 4 gr sock 4 LED_ye LED_ye LED_ye sock 5 sock 6 sock 5 pi LED_ye LED_ye LED_ye sock 6 re LED_ye LED_ye LED_ye sock 7 sock 7 bk LED_ye LED_ye sock 8 Master trunk cable 3x1mm² x n x 0.34mm²; Hallogen 2001350000 – 2015/2016 vi LED_ye 8-way LED_ye sock 8 LED_ye bl gr/pi wh re/bl gn wh/gn ye br/gn gr 4-way 10...30 V 2A 4A 10 A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes Wiring diagram gn/ye wh/ye rs ye/br re wh/gr bk gr/br vi 8-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram 4-way Technical data G.19 M12 Push-Pull Passive distributors with M23 outlet SAI-4/8-S Ordering data Complete modules Note 4-channel 8-channel Type SAI-4-S 4P FC SAI-8-S 4P FC QTY 1 1 Other versions on request 4-pole Order No. 1847960000 1847920000 SAI-4/8-S Type SAI-4-S 5P FC SAI-8-S 5P FC Other versions on request 5-pole QTY 1 1 Order No. 1847970000 1848040000 G 12 19 LED_gn LED_gn sock 1 sock 1 1 sock 2 sock 2 2 LED_ye LED_ye LED_ye 4 LED_ye LED_ye sock 5 5 LED_ye LED_ye LED_ye sock 6 sock 6 6 LED_ye LED_ye LED_ye sock 7 7 LED_ye sock 8 8-way 8 6 17 13 2 10 11 LED_ye LED_ye LED_ye sock 8 14 3 sock 4 LED_ye sock 5 8 16 sock 3 3 sock 4 4 5 LED_ye LED_ye LED_ye sock 3 15 LED_ye LED_ye LED_ye sock 7 G.20 6 LED_ye 4-way 10...30 V 2A 4A 9A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... 4-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram Wiring diagram LED_ye 18 1 8-way Technical data 2001350000 – 2015/2016 with M23 outlet on front 26.8 16 18.8 4.5 4.5 73 107 152 29 54 Passive distributors M12 Push-Pull M23 33 39 SAI-4/8-SH Ordering data Complete modules Note 4-channel 8-channel Type SAI-4-SH 4P FC SAI-8-SH 4P FC QTY 1 1 4-pole Order No. 1859110000 1859120000 SAI-4/8-SH Type SAI-4-SH 5P FC SAI-8-SH 5P FC 26 QTY 1 1 5-pole Order No. 1859130000 1859140000 G 10...30 V 2A 4A 9A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... /('B\H ZD\ZD\ Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram Wiring diagram /('B\H VRFN /('B\H VRFN /('B\H VRFN /('B\H VRFN /('B\H VRFN /('B\H VRFN /('B\H ZD\ZD\ Technical data VRFN /('B\H /('B\H VRFN /('B\H /('B\H VRFN /('B\H /('B\H VRFN /('B\H /('B\H VRFN /('B\H /('B\H VRFN /('B\H /('B\H VRFN VRFN /('B\H /('B\H /('B\H VRFN /('BJQ 2001350000 – 2015/2016 VRFN /('B\H /('BJQ G.21 M12 Push-Pull Hood version Passive distributors SAI-8-M SAI-8-M Ordering data 8-channel Technical data Other versions on request 5-pole Order No. 1848070000 Dimensioned drawing 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PE 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1–8 1–8 1–8 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 1 3 5 Colour Contact Slot M12 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Terminal 10...30 V 2A 4A 8 x ye Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) QTY 1 8 x ye Note Type SAI-8-M 5P FC 8-way Complete modules 4-way G white green yellow grey pink red black violet grey/pink red/blue white/green brown/green white/yellow yellow/brown white/grey grey/brown brown (+) blue (–) green/yellow (PE) Master trunk cable 3x1mm² x n x 0.34mm²; halogen-free G.22 2001350000 – 2015/2016 M12 Push-Pull CNOMO SAI-4/8-F 1 1 5-pole Type SAI-4-F 5P CNOMO 5M SAI-4-F 5P CNOMO 10M QTY 1 1 Order No. 1861570000 1861560000 SAI-8-F 5P CNOMO 5M SAI-8-F 5P CNOMO 10M 1 1 1861550000 1861590000 G 1861540000 1861580000 16 gr/br 15 wh/gr 14 ye/br 13 wh/ye 12 br/gn 11 wh/gn 10 re/bl 9 gr/pi bk 8-way sock8 7 Sock 8 Sock-M12-5P Sock 7 Sock-M12-5P vi 8 Dimensioned drawing 6 re sock6 pi 5 Sock 6 Sock-M12-5P Sock 5 Sock-M12-5P sock7 4 ye sock4 4-way gr 3 Sock 4 Sock-M12-5P sock5 Sock 3 Sock-M12-5P gn 2 wh 1 bl (–) 18 Sock-M12-5P Sock 2 sock3 ST-M23-19P 10...50 V 2A 4A 12 A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes SAI-4-S 5P CNOMO SAI-8-S 5P CNOMO Dimensioned drawing Max. total current with 4-channel distributor is 8A. And with 8-channel distributor is 12A 2001350000 – 2015/2016 Order No. br (+) gn/ye sock2 PE 17 4-channel 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 5-pole Cable length 5 m Cable length 10 m Sock-M12-5P Note QTY Sock 1 M23 Type 8-way 8-channel Cable length 5 m Cable length 10 m SAI-4/8-S 4-way 4-channel Ordering data Passive distributors SAI-4/8-S sock1 Numbers for designation on PCB G.23 M12 Push-Pull Bayonet joint Passive distributors SAI-8-SHB G SAI-8-SHB Ordering data Complete modules Note 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-8-SHB 5P FC QTY 1 Other versions on request 5-pole Order No. 1872440000 Dimensioned drawing 10...30 V 2A 4A 9A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... violet 8 black 7 sock8 sock7 red 6 16 grey-brown 15 white-grey 14 yellow-brown sock6 pink 5 sock5 grey 4 yellow 3 green 2 white 1 sock4 13 white-brown 12 brown-green 11 white-green sock3 sock2 sock1 10 red-blue 9 grey-pink blue 18 brown 17 green-yellow PE G.24 2001350000 – 2015/2016 M12 Push-Pull SAI-8-SHB Passive distributors Bayonet joint with socket connector on reverse SAI-8-SHB Ordering data Complete modules Note 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-8-SHB 5P F13 FC QTY 1 Other versions on request 5-pole G Order No. 1872460000 Dimensioned drawing 10...30 V 2A 4A 9A 3 IP 67 -25...80 °C PA 6 GF PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... green 12 Terminal 11 Terminal 10 Terminal 9 Terminal 8 Terminal (KSR 2) 7 Terminal + 24 V (Thermocontact) 6 Terminal 5 Terminal (KSR 1) Shield V 4 Terminal (Shield-KSR) 8 xyellow 3 Terminal (Thermocontact) 2 Terminal 1 Terminal 13 Terminal Female connector 13 pole at rear 2001350000 – 2015/2016 G.25 Passive distributors M12 IDC IDC – the quick connection Hood version •Compact IDC connection cuts production, commissioning and maintenance work •Robust, knurled metal nut, safe handling requiring little force •The dimensions of the IDC distributor correspond to and are compatible with the standard SAI distributor. •Plug-in connection module for bus cables enhances on-site flexibility •Three sizes for 4, 6 and 8 channels •3-pole version with one I/O signal per channel, 4-pole version with two I/O signals per channel •Individual on site assembly of sensor/actuator lines •Fast, reliable connection with IDC connection element •IP 67 Ingress protection classification. + ( ) G - ( ) Factory setting (see wiring diagram) Current bridged + ( ) - ( ) SAI fixed cable version Current isolated •Pre-assembled bus cables minimise installation work and avoid wiring errors •3 sizes for 4, 6 and 8 channels •Highly flexible, cable carrier compatible bus cables with polyurethane (PUR/PVC) sheathing – 3 x 0.75 mm2 – n x 0.34 mm2, •3-pole version with one I/O signal per channel, 4-pole version with two I/O signals per channel IDC connection element Ordering data Type SAI-SA-3-IDC SAI-SA-4-IDC G.26 Qty. 1 1 Order No. 9457720000 1766810000 2001350000 – 2015/2016 Passive distributors M12 IDC The significant advantages of Weidmüller tools: •Easy handling •Very small, ideal for confined assembly conditions •Patented solution •Metal Connectors Insulation displacement connections on Weidmüller SAI distributors are currently the smallest but also the most robust connection elements on the market. Thanks to their extremely small dimensions, corresponding distributors are available with the same dimensions in M12 or IDC versions. For large series, e.g. where more than 100 modules are used every year, we recommend using a special tool to simplify the handling of the connected lines even further. However, this tool is not always necessary because all connection elements can usually be readily tightened by hand. G IDC-Tool Ordering data Type SAI-IDC-Tool Qty. 1 Order No. 1795020000 Screwty® The IDC elements can also be tightened with the Weidmüller Screwty®. Ordering data Type Screwty®-M12-DM Qty. 1 Order No. 1900001000 Qty. 10 Order No. 1794850000 Protective cap M12 for IDCw Ordering data Type SAI-SK-M12 IDC 2001350000 – 2015/2016 G.27 M12 IDC Hood version 6$,0 6$,0 6$,0 Mounting hood Note 4-channel 6-channel 8-channel SAI-4-M 3P IDC UT SAI-6-M 3P IDC UT SAI-8-M 3P IDC UT Screw connection Screw connection Tension-clamp connection Tension clamp connection Technical data Other versions on request Wiring diagram 10...30 V 2A 4A 10 A 2 IP 67 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.08...1.5 mm² blue SAI-4/6/8-M IDC Order No. 1760040000 1760050000 1760060000 2 2 2 1760041000 1760051000 1760061000 SAI-4-M 4P IDC UT SAI-6-M 4P IDC UT SAI-8-M 4P IDC UT 1 50 1 50 1724750000 1724750050 1752080000 1752080050 SAI-4/6/8-MH BL3.5 SAI-4/6/8-MH BL3.5 SV SAI-4/6/8-MH BLZF3.5 SAI-4/6/8-MH BLZF3.5 SV Type SAI-4-M 4P IDC SAI-6-M 4P IDC SAI-8-M 4P IDC Other versions on request Wiring diagram red 8-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) SAI-4/6/8-MH BL3.5 SAI-4/6/8-MH BL3.5 SV SAI-4/6/8-MH BLZF3.5 SAI-4/6/8-MH BLZF3.5 SV 3-pole QTY 1 1 1 4-way Base unit 4-channel 6-channel 8-channel Type SAI-4-M 3P IDC SAI-6-M 3P IDC SAI-8-M 3P IDC 6-way Complete modules EOXH 4-pole QTY 1 1 1 Order No. 1766780000 1766790000 1766800000 2 2 2 1766781000 1766791000 1766801000 1 50 1 50 1724750000 1724750050 1752080000 1752080050 UHG ZD\ZD\ZD\ SAI-4/6/8-M IDC Ordering data G Passive distributors With dual power supply: 2x8 = 16 A total current Clamping range up to 2.5 mm² with screw connection G.28 2001350000 – 2015/2016 M12 IDC 6$, 6$, 6$, SAI-4/6/8-F IDC Ordering data 4-channel 6-channel 8-channel Note 3-pole Cable length 5 m Cable length 10 m Type SAI-4-F 3P IDC PUR 5M SAI-4-F 3P IDC PUR 10M QTY 1 1 Order No. 1766720000 1766730000 Cable length 5 m Cable length 10 m SAI-6-F 3P IDC PUR 5M SAI-6-F 3P IDC PUR 10M 4 1 Cable length 5 m Cable length 10 m SAI-8-F 3P IDC PUR 5M SAI-8-F 3P IDC PUR 10M 1 1 Other versions on request Passive distributors Fixed cable version SAI-4/6/8-F IDC 4-pole Type SAI-4-F 4P IDC PUR 5M SAI-4-F 4P IDC PUR 10M QTY 1 1 Order No. 1766660000 1766670000 1766740000 1766750000 SAI-6-F 4P IDC PUR 5M SAI-6-F 4P IDC PUR 10M 1 1 1766680000 1766690000 1766760000 1766770000 SAI-8-F 4P IDC PUR 5M SAI-8-F 4P IDC PUR 10M 1 1 1766700000 1766710000 Other versions on request G brown brown blue blue white white grey/pink green green red/blue yellow yellow grey grey 4-way white/green 4-way 10...30 V 2A 4A 9A 2 IP 67 -20...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes brown/green pink pink white/yellow red 6-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram Wiring diagram red 6-way Technical data yellow/brown black black 2001350000 – 2015/2016 violet 8-way 8-way violet white/grey grey/brown G.29 Passive distributors M12 VA stainless steel Fixed cable version, Suitable specifically for usage in food processing machinery SAI-8-F 5P M12 5M VA 60 SAI-8-F 5P M12 5M VA Ordering data 8-channel Note Cable length 5 m QTY 1 Dimensioned drawing Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Fire behaviour Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-8-F 5P M12 5M VA 10...30 V 2A 4A 12 A 3 IP 69K -25...70 °C Stainless steel CuZn Stainless steel Silver V-0 ... Yes 5-pole Order No. 1865310000 gn/ye LED_gn br bl sock 1 wh LED_ye sock 2 gn LED_ye sock 3 ye LED_ye sock 4 gr 4-way G 4 4.5 27 164 27 27 13.5 39 33 LED_ye sock 5 sock 6 pi LED_ye re LED_ye sock 7 bk sock 8 Accessory (incl.): 4 protective caps for unused slots G.30 vi LED_ye 8-way LED_ye 2001350000 – 2015/2016 Stainless steel M12 VA - Accessories Tension-clamp connection M12, stainless steel SAIS / SAIB VA Ordering data Male Female Note Passive distributors Straight 5-pole, PG 9 5-pole, PG 9 Type SAIS 5/9-VA SAIS 5/9-VA-B-COD QTY 1 1 Order No. 1920700000 1920720000 5-pole, PG 9 5-pole, PG 9 SAIB 5/9-VA SAIB 5/9-VA-B-COD 1 1 1920710000 1920730000 Technical data Type of connection Housing main material Contact tube diameter Cable diameter Wire cross-section, min. / max. Rated current Rated voltage Temperature range of housing Protection degree Contact surface Note PB = PROFIBUS (B-COD) Dimensioned drawing FD 2001350000 – 2015/2016 &DEOHHQWU\ ²PP FD &DEOHHQWU\ ²PP PB = PROFIBUS (B-COD) G Tension clamp connection 1.4404/316L M12 6...8 mm (PG9) 0.25...0.5 mm² 4A 125 V -40 … +85 ° C IP 69K Gold-plated 0[ 0[ G.31 Passive distributors M12 metal distributors Sensor-actuator distributors for special applications All-metal SAI-4/8-FMM M12 Shielded cable, e.g. for analogue initiators Some applications need full shielding from sensor to control. This is possible with the all metal SAI distributors. The distributors are supplied with an EMC cable gland. Initiator LEDs are omitted. Especially thick trunk cable It is sometimes advisable to use the machine manufacturer’s standard trunk cable. This cable will usually have a relatively large outside diameter and will therefore require plenty of space (SAI-4/6/8 MHD). All-metal fixed cable distributors Weidmüller metal distributors have proved their worth in many situations. They are available as 4 and 8 channel M12 versions with cable lengths of 5 or 10 m. Metal distributors are also necessary when ESD requirements must be complied with. The conductive metal surface provides low surface resistance. Advantages: • No ESD/EMC problems •High resistance to chemicals or mechanical loads • Standard mounting dimensions G SAI-M with metal hood SAI-4/6/8 MMS SAI-4/6/8 MM MMS: Modular, Metal, Shield MM: Modular, Metal G.32 SAI-4/6/8 MH MH: Modular, High SAI-4/6/8 MHD MHD: Modular, High, sealeD (for especially thick cables) SAI-4/6/8 MMS with EMC cable gland in metal housing Cable gland: M20 Cable gland: M25 For especially tough conditions where plastic is totally unsuitable. In certain cases it makes sense to avoid the use of plastics altogether. In such cases a distributor made completely from metal is required that can be connected to others using metal cable glands, without additional connections for the shielding. For cables with outside insulation diameter from 10 mm to 14 mm. Listed below are just some of the cable sizes that are suitable for the SAI distributor with M20 cable gland: • 14 x 0.50 mm2 to 16 x 0.50 mm2 • 8 x 0.75 mm2 to 15 x 0.75 mm2 • 8 x 1.00 mm2 to 10 x 1.00 mm2 • 5 x 1.50 mm2 to 7 x 1.50 mm2 For cables with outside insulation diameter from 13 mm to 18 mm. Listed below are just some of the cable sizes that are suitable for the SAI distributor with M25 cable gland: • 21 x 0.50 mm2 • 18 x 0.75 mm2 to 21 x 0.75 mm2 • 14 x 1.00 mm2 to 20 x 1.00 mm2 • 8 x 1.50 mm2 to 16 x 1.50 mm2 2001350000 – 2015/2016 Passive distributors M12 metal distributors Overview of metal distributors Type SAI-4-MH-4P M12 SAI-6-MH-4P M12 SAI-8-MH-4P M12 SAI-4-MH-5P M12 SAI-6-MH-5P M12 SAI-8-MH-5P M12 SAI-4-MHD-5P M12 SAI-6-MHD-5P M12 SAI-8-MHD-5P M12 SAI-4-MHD-4P M12 SAI-6-MHD-4P M12 SAI-8-MHD-4P M12 SAI-UT PBT PBT PBT PBT PBT PBT PBT PBT PBT PBT PBT PBT Sockets 4 6 8 4 6 8 4 6 8 4 6 8 M12 4 4 4 5 5 5 5 5 5 4 4 4 Poles–Hood Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Zn-G Form high high high high high high high high high high high high Cable gland M20 M20 M20 M20 M20 M20 M25 M25 M25 M25 M25 M25 Cable gland plastic plastic plastic plastic plastic plastic plastic plastic plastic plastic plastic plastic SAI-4-MMS-4P M12 SAI-8-MMS-4P M12 SAI-4-MMS-5P M12 SAI-8-MMS-5P M12 Zn-G Zn-G Zn-G Zn-G 4 8 4 8 4 4 5 5 Zn-G Zn-G Zn-G Zn-G low low low low M20 M20 M20 M20 EMC EMC EMC EMC 1783540000 1783530000 1783520000 1783510000 SAI-4-MM-5P M12 SAI-8-MM-5P M12 Zn-G Zn-G 4 8 5 5 Zn-G Zn-G low low M20 M20 brass brass 1783500000 1783490000 Zn-G Zn-G Zn-G Zn-G Zn-G high high high high high M20 M25 M20 M20 M20 plastic plastic plastic plastic plastic 1724752000 1724753000 1782760000 1782740000 1782750000 SAI-4/6/8 MH-MH BL 3.5 SAI-4/6/8 MH-MHD BL 3.5 SAI-8-MH-5P M12 ZF III SAI-8-MMS-5P M12 ZF III SAI-4/6/8 MH-MH BL-ZF 3.5 PBT Zn-G 8 8 5 5 SAI-4-FMM-4P M12 5M Zn-G 4 4 SAI-4-FMM-4P M12 10M Zn-G 4 4 SAI-8-FMM-4P M12 5M Zn-G 8 4 SAI-8-FMM-4P M12 10M Zn-G 8 4 Note:The cable outside diameter can vary from manufacturer to manufacturer. It is therefore possible that the cable glands hold other cables firmly despite a different strand lay-up. Length 5 m 10 m 5 m 10 m Order No. 1705922000 1705932000 1705942000 1701232000 1701242000 1701252000 1701233000 1701243000 1701253000 1705923000 1705933000 1705943000 G 9456190002 9456200002 9456750002 9456760002 In each case, it is best to first measure the cable diameter and then choose an appropriate distributor. 2001350000 – 2015/2016 G.33 M12 metal distributors Fixed cable version Passive distributors SAI-4-FMM 6$, 6$, 6$, SAI-4-FMM Ordering data Order No. 9456190002 9456200002 Cable length 5 m Cable length 10 m SAI-8-FMM-4P M12 5M SAI-8-FMM-4P M12 10M 1 3 9456750002 9456760002 Technical data BU8 3 2 M12 / 4POL 6 4 1 5 6 4 1 5 BU7 3 2 M12 / 4POL BU6 3 2 M12 / 4POL 6 4 1 5 6 4 1 5 BU5 3 2 M12 / 4POL 3 2 BU4 M12 / 4POL 6 4 1 5 6 4 1 5 BU3 3 2 M12 / 4POL BU2 3 2 M12 / 4POL G.34 BN GN/GE GN/YE BR BL BU GN GN GR GY RT RD VT VI WS WH GE YE RS PK SW BK R1 4K7 V1 LED–GN PE 10...30 V 2A 4A 9A 3 IP 68 -20...90 °C Zinc diecast PBT (UL 94 V0) CuZn CuZn, nickel-plated Silver V-0 ... Yes 6 4 1 5 Dimensioned drawing 6 4 51 2 Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Additional variants on request Bus cable is not shielded BU1 3 M12 / 4POL Note Cable length 5 m Cable length 10 m QTY 4 3 8-WAY 8-channel 4-pole Type SAI-4-FMM-4P M12 5M SAI-4-FMM-4P M12 10M 6-WAY 4-channel 4-WAY G 2001350000 – 2015/2016 Hood version SAI-4/6/8-MMS Ordering data Complete shielding transmission via the housing 2001350000 – 2015/2016 1783520000 1783510000 8-channel Screw connection Technical data SAI-4/6/8 MH-MM BL 3.5 With EMC cable gland 1 1724754000 QTY M12 Order No. SAI-4-MM 5P M12 SAI-8-MM 5P M12 SAI-8-MMH 5P M12 ZF 1 1 1 1783500000 1783490000 1782740000 SAI-8-MM 5P M12 UT 2 1783491000 SAI-4/6/8 MH-MM BL 3.5 1 1724754000 MM without initiator LED and with standard metal cable gland G Wiring diagram Wiring diagram 10...30 V 2A 4A 10 A 3 -20...90 °C Zinc diecast PBT (UL 94 V0) CuZn CuZn, nickel-plated Silver V-0 0.08...1.5 mm² 4-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 1 1 Type 6-way Note SAI-4-MMS 5P M12 SAI-8-MMS 5P M12 SAI-4/6/8-MM 8-way Mounting hood Order No. 1783540000 1783530000 4-way Tension-clamp connection, high cover Base unit 4-channel 8-channel 8-channel QTY 1 1 6-way Complete modules, 5-pole 4-channel 8-channel M12 Type SAI-4-MMS 4P M12 SAI-8-MMS 4P M12 8-way Complete modules, 4-pole 6$,0 6$,0 6$,0 Passive distributors M12 metal distributors G.35 M12 metal distributors Hood version with M20 outlet Passive distributors 39 33 55 107 73 SAI 4-M =102 SAI 6-M =152 SAI 8-M =156.5 4.5 15 18 21 60 SAI-4/6/8-MH Ordering data Complete modules Tension-clamp connection Mounting hood Note 4-channel 6-channel 8-channel 8-channel Screw connection Tension-clamp connection Type SAI-4-MH-4P M12 SAI-6-MH-4P M12 SAI-8-MH-4P M12 SAI-4/6/8 MH-MH BL 3.5 SAI-4/6/8 MH MH BLZF3,5 Other versions on request 4-pole QTY 1 1 1 Order No. 1705922000 1705932000 1705942000 1 1 1724752000 1782750000 SAI-4/6/8-MH Type SAI-4-MH-5P M12 SAI-6-MH-5P M12 SAI-8-MH-5P M12 SAI-8-MH-5P M12 ZF III SAI-4/6/8 MH-MH BL 3.5 SAI-4/6/8 MH MH BLZF3,5 Other versions on request 5-pole QTY 1 1 1 1 Order No. 1701232000 1701242000 1701252000 1782760000 1 1 1724752000 1782750000 G red EOXH 4-way -20...90 °C Pocan (base module), Zinc diecast (hood) PBT (UL 94 V0) CuZn CuZn, nickel-plated Silver V-0 0.08...1.5 mm² blue 8-way Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 10...30 V 2A 4A 10 A 3 6-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Wiring diagram Wiring diagram With dual power supply: 2x8 = 16 A total current Clamping range up to 2.5 mm² with screw connection G.36 UHG ZD\ZD\ZD\ Technical data 2001350000 – 2015/2016 M12 metal distributors 6$,0 6$,0 6$,0 SAI-4/6/8-MHD Ordering data Complete modules Mounting hood Note 4-channel 6-channel 8-channel Screw connection Type SAI-4-MHD-4P M12 SAI-6-MHD-4P M12 SAI-8-MHD-4P M12 SAI-4/6/8 MH-MHD BL 3.5 Other versions on request 4-pole QTY 1 1 1 Order No. 1705923000 1705933000 1705943000 1 1724753000 Passive distributors Hood version with M25 outlet SAI-4/6/8-MHD Type SAI-4-MHD-5P M12 SAI-6-MHD-5P M12 SAI-8-MHD-5P M12 SAI-4/6/8 MH-MHD BL 3.5 Other versions on request 5-pole QTY 1 1 1 Order No. 1701233000 1701243000 1701253000 1 1724753000 G blue red 6-way 8-way 4-way -20...90 °C Pocan (base module), Zinc diecast (hood) PBT (UL 94 V0) CuZn CuZn, nickel-plated Silver V-0 0.08...1.5 mm² red 6-way Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) 10...30 V 2A 4A 10 A 3 blue 8-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Wiring diagram Wiring diagram 4-way Technical data With dual power supply: 2x8 = 16 A total current Clamping range up to 2.5 mm² with screw connection 2001350000 – 2015/2016 G.37 Passive distributors M12 distributors 1:1 Passive For switching with five no-voltage contacts in an M12 without LED with hood Emergency stop wiring Sometimes a machine builder will need more than two floating contacts in one M12 plug-in connector. This is the case, for example, in the wiring for some “emergency stop” circuits. It was for this application that Weidmüller developed the 1:1 SAI distributor. This SAI distributor has four M12 plug-in connectors with five floating contacts in one socket connector. The distributor is supplied complete with hood. When connecting PT100 3- and 4-conductor initiators, we recommend the new shielded metal version. If you need other circuit configurations, simply contact us. Note: This distributor should not be used as the base module for active bus distributors. G base element metal Wiring diagram Socket 1 1 1 1 1 2 2 2 2 2 3 3 3 3 3 4 4 4 4 4 – Contact 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 – BL 3.5 contact 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Technical data Current per channel Total current LEDs Ordering data Type SAI-4-M 5P M12 1:1 (plastic hood) Base element (plastic) SAI-4-MMS 5P M12 1:1 (metal hood) G.38 2A 8A No LEDs are integrated at any point. Qty. 1 1 1 Order No. 1806010000 1806011000 1897680000 2001350000 – 2015/2016 Passive distributors M12 Combi distributor SAI distributor with 8 poles per M12 8-pole G Applications This distributor can be used both as a base module for satellite solutions (SAI-Combi) and for connecting sensors/units with more than two contacts. Sensors, units with more than two signals in one line As one socket in this module contains four signal paths and, in addition, two +, two – and one PE, components with more than two signal lines can be connected to this module. Eight-pole connecting cables are available on request. Wiring M12 socket 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 1/3 2/4 1/3 2/4 1/2/3/4 M12 contact 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 5 5 6/7 6/7 8 BL 3.5 connection 1 3 5 7 2 4 6 8 9 11 13 15 10 12 14 16 17 19 18 20 PE PLC input E0.0 E0.1 E0.2 E0.3 E0.4 E0.5 E0.6 E0.7 E1.0 E1.1 E1.2 E1.3 E1.4 E1.5 E1.6 E1.7 Supply 24 V 24 V 0V 0V PE The jumpers in the distributor enable the potentials of 17 and 19 or 18 and 20 to be bridged Contacts 6 and 7 are bridged in the 8-pole M12 in order to increase the current-carrying capacity. total current per M12: 2 A, signal current per pin: 1 A Ordering data Type Complete module: SAI-4-M 8P M12 Base separate: SAI-4-M M12 UT Matching hood passive: SAI-4/6/8-MH-BL3.5 Technical information:The distributor does not include any signalling LEDs. Qty. 1 1 1 Order No. 1807640000 1807641000 1724750000 Supply LEDs and electrical isolation are provided 2001350000 – 2015/2016 G.39 Passive distributors M12 distributor for NPN and PNP sensors Fixed cable version Fixed cable version This distributor includes the option of attaching either a PNP sensor or an NPN sensor with 2 or 3 conductor connection to an M12 socket. Eight inputs are available in total. In the case of a switched sensor, a + signal on the corresponding wire is connected through and the appropriate LED is illuminated. The upper LED “N” is illuminated for NPN sensors and the lower LED “P” for PNP sensors. Do not connect a T-piece to the M12 socket. The existing M12 plug-in connectors are wired in such a manner that the PNP sensor can be connected to pin 4 and the NPN sensor to pin 2. The distributor has eight channels and 5 m of cable. Other versions are also available. G 5 4.5 36 152 107 73 Pin assignment ø4 60 1 4 1 4 Function Pin Function Output Wire colour 4 4 4 4 4 4 4 4 1 3 5 PNP PNP PNP PNP PNP PNP PNP PNP 24 V DC 0 V DC PE 2 2 2 2 2 2 2 2 NPN NPN NPN NPN NPN NPN NPN NPN 1 2 3 4 5 6 7 8 white green yellow grey pink red black violet brown blue green/yellow 3 Operating voltage Operation temperature Storage temperature Ingress protection class PUR cable Max. no-load current for 2-wire NPN sensors Ordering data Type SAI-8-F 5P NPN-PNP 5M NPN Sensor 2 2 5 Wiring diagram (schematic) 3 Pin Wire size 0.34 mm2 0.34 mm2 0.34 mm2 0.34 mm2 0.34 mm2 0.34 mm2 0.34 mm2 0.34 mm2 0.75 mm2 0.75 mm2 0.75 mm2 Technical data M12 sockets Pin 1 = +24 V DC Pin 2 = NPN Input Pin 3 = 0 V DC Pin 4 = PNP Input Pin 5 = PE M12 socket 1 2 3 4 5 6 7 8 all all all 24 V DC ±20 % 0...80 °C –25...80 °C IP 68 5m 2 mA DC Qty. 1 Order No. 1814990000 Cable+ 24 V DC PNP Sensor G.40 2001350000 – 2015/2016 M12 wall bushing Wall bushing 4.5 Passive distributors SAI-8-B 5P M12 SL 39 33 3 25 152 107 73 4 16.5 19.5 60 SAI-8-B 5P M12 SL Ordering data Type SAI-8-B 5P M12 SL Note QTY 1 Order No. 1847560000 BL 3.5 connector included in delivery Technical data Dimensioned drawing red 7.5 36 31 blue 46 4-way 10...30 V 2A 3A 10 A 3 IP 65 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.08...1.5 mm² 8-way 6-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) G 5-pole 2001350000 – 2015/2016 G.41 Passive distributors M12 wall bushing Overview Distributors for system cabling On site distribution is becoming more important. For example, in some places the IP 20 I/O module has to be mounted in housings directly on the machine. This is where a simplified form of wiring is essential. Weidmüller now offers two simple solutions Advantages •Sensors and actuators can be plugged in from outside • Through-panel version can be mounted in cut outs in steel panels • Standardised ribbon cable connector inside • Plus: M12 through-panel feed that can be plugged in from both sides Hexagonal nut M4 DIN 985 Washer 4.3 DIN 125 Polyamide Screw M4x30 SAI-8-B 4P M12 F10 Plug connector X2 Plug connector X1 Mounting face d = 1.5...6 mm Drilling template 40 ±1 15 ±0.5 X2 40 ±1 ø 4.5 36 ±0.2 G •A distributor equipped at the rear with a standardised ribbon cable connector, which is compatible with the Weidmüller PLC system interface. •Weidmüller also offers a unique solution for feeding bus cables through panels that can be plugged in from both sides. X1 R5 73 ±0.2 107 ±0.2 G.42 2001350000 – 2015/2016 Passive distributors M12 wall bushing Advantages of system cabling Fast • Time saving installation •Reduces commissioning and trouble-shooting times • On site wiring cuts wiring costs Contact assignment Male connector X1 M12 socket 1 ... 8 1 ... 8 1 ... 8 Pin 1 Pin 3 Pin 5 Male connector X1 U+ U– PE Male connector X1 M12 socket 10 8 6 4 2 UPE U+ 1 9 7 5 3 1 4 2 5 3 Safe • Reduces installation errors •Using system cables instead of individual wires improves clarity in control cabinets •Direct marking corresponding to the PLC Variability • Additional I/O modules available • Cable length options •Easy replacement of I/O interfaces provides flexibility Contact assignment Male connector X2 M12 socket 1 2 3 4 5 6 7 8 1–8 1–8 Pin 4 Pin 4 Pin 4 Pin 4 Pin 4 Pin 4 Pin 4 Pin 4 Pin 1 Pin 3 Male connector X2 1 2 3 4 5 U6 PE 7 8 U+ 9 10 Male connector X2 10 8 6 4 2 Note: You will find further products for Interface units and PLC solutions in the Electronic catalogue 4.5. 9 7 5 3 1 G Technical data 10 – 30 V (DC) max. 1 A per channel / max. 8 A in total max. 1 A in total Operating voltage Outputs Inputs Mounting conditions Mounting surface sheet steel, flat, min. 1.5 mm thick, or panels with at least equivalent stability, max. 6 mm thick max. 40 °C IP 67/IP 68 only in conjunction with control cabinets with equivalent class of protection 4 screws + washers + nuts / torque: 0.8 Nm Surface temperature Ingress protection class Fixings Note: Connect the male connector 3.5 (X1) when using actuators Ordering data Distributor Male connector X1 2001350000 – 2015/2016 Type SAI-8-B 4P M12 F10 BL 3.50/07/180 SN DKGN BX Qty. 1 50 Order No. 1812170000 1606530000 G.43 Passive distributors Solutions to customer specification Pre-assembled hood version In some cases, it can be advantageous to receive the hoods in pre-assembled form. Here MF means: basic modules are supplied along with assembled hoods. Here MHF are the assembled hoods only. The wire cross-sections are 3 x 1 mm2 and n x 0.34 mm2. The quality of conduction is identical to that of fixed cable distributors. Technical data can be found on pages W.2 and W.9 SAI distributor with pre-assembled hood Colour-coded cable Ordering data G Type 8-channel SAI-8-MF 4P PUR 5M SAI-8-MF 4P PUR 10M Ordering data Type 4-channel SAI-4-MF 5P PUR 5M SAI-4-MF 5P PUR 10M 8-channel SAI-8-MF 5P PUR 5M SAI-8-MF 5P PUR 10M Pre-assembled hood Colour-coded cable Length 5 m 10 m Length 4-pole Order No. 1799960000 1789190000 5-pole Order No. 5 m 10 m 1804600000 1804580000 5 m 10 m 1804590000 9457430000 Ordering data Type SAI-4/6/8-MHF 4P PUR 4M SAI-4/6/8-MHF 4P PUR 6M SAI-4/6/8-MHF 4P PUR 9M SAI-4/6/8-MHF 4P PUR14M SAI-4/6/8-MHF 4P PUR20M SAI-4/6/8-MHF 4P PUR28M SAI-4/6/8-MHF 4P PUR34M Matching base module Type SAI-4-M-4PM12UT SAI-6-M-4PM12UT SAI-8-M-4PM12UT 4-pole Length 4 m 6 m 9 m 14 m 20 m 28 m 34 m Order No. 1791450400 1791450600 1791450900 1791451400 1791452000 1791452800 1791453400 Qty. 1 1 1 Order No. 1705921000 1705931000 1705941000 Length 4m 6m 9m 10 m 14 m 16 m 20 m 28 m 34 m 40 m 50 m 55 m Order No. 1791460400 1791460600 1791460900 1791461000 1791461400 1791461600 1791462000 1791462800 1791463400 1791464000 1791465000 1791465500 Qty. 1 1 1 Order No. 1701231000 1701241000 1701251000 Pre-assembled hood Ordering data Type SAI-4/6/8-MHF 5P PUR 4M SAI-4/6/8-MHF 5P PUR 6M SAI-4/6/8-MHF 5P PUR 9M SAI-4/6/8-MHF 5P PUR10M SAI-4/6/8-MHF 5P PUR14M SAI-4/6/8-MHF 5P PUR16M SAI-4/6/8-MHF 5P PUR20M SAI-4/6/8-MHF 5P PUR28M SAI-4/6/8-MHF 5P PUR34M SAI-4/6/8-MHF 5P PUR40M SAI-4/6/8-MHF 5P PUR50M SAI-4/6/8-MHF 5P PUR55M Matching base module Type SAI-4-M-5PM12UT SAI-6-M-5PM12UT SAI-8-M-5PM12UT G.44 5-pole 2001350000 – 2015/2016 M12 distributor accessories SAI-4/6/8-MH LEER Ordering data SAI-4/6/8-MH LEER Mounting hood Note Empty SAI-TS35 MF Passive distributors Protective cap for hooded distributor, empty, Terminal rail foot for distributor Type SAI-4/6/8-MH LEER QTY 1 4-pole Order No. 1783460000 G Type SAI-TS35 MF QTY 1 Order No. 1917400000 Dimensioned drawing 52 A 36 73 89 A-A M4 M4 6.3 A M4 M4 1x45° 3 2001350000 – 2015/2016 G.45 Passive distributors M8 distributors SAI-M8 Weidmüller offers two different series for the M8 range. Both of these series offer key advantages: while one is optimised for size, the other has a patented shape and protected design that make it easy to handle. The SAI M8 product line is available with up to 12 plug in slots (as a fixed-cable version) and with up to 10 plug-in slots (as a pluggable version). The housings can be screwed on from the side or from the top which makes them more versatile. They are durable and well-sealed with a sturdy, fully encapsulated construction. These single row distributors are easy to handle; their compact shape makes them one of the smallest product solutions available on the market. The hooded distributor is a favourite from the line or ergonomic distributors (also nicknamed the hedgehog distributor). The cable outlet is customisable and can exit from the top or from the back. These distributors are also fully encapsulated. G G.46 2001350000 – 2015/2016 Passive distributors M8 distributors Easily accessible The side-mounted M8 connector ensures very convenient handling Directly on the PCB Custom versions are also available. This is the PCB connection module. Space-saving The line version has a very small size. 2001350000 – 2015/2016 G G.47 Passive distributors M8 distributors Overview Fixed cable version Compact dimensions, readily accessible M8 connections, eye-catching design The unconventional design of this generation of SAI M8 distributors catches the eye immediately. Their shape is helpful because in this patented design the sockets are no longer arranged in simple rows. Instead, some are on 45° bevelled surfaces. That considerably improves the accessibility of the screw connections for the sensor and actuator cables. Ease of use, compact dimensions and the eye catching design are the obvious advantages of this M8 generation. The following variations are available: G Hood version • SAI M8 distributor with removable connection hood; the bus cable can be connected either vertically or horizontally • SAI M8 distributor with permanently attached, pre-assembled bus cable, 5 or 10 m long; this version is particularly slim and is therefore ideal for mounting in confined spaces • SAI M8 distributor with metal plated M23 thread M23 version G.48 2001350000 – 2015/2016 M8 distributors M8 distributor with M12 outlet Passive distributors SAI-M8-Line Extra-narrow M8 distributor for confined spaces Single-row M8 distributors are the smallest sensor-actuator modules currently available with this thread size and it is precisely their size that is a decisive factor for applications and this form has become very popular. It is important to maintain the widest possible range of options. The SAI-M8-Line products can provide many interesting solutions: M8 distributor line / fixed-cable version •4 and 6 channel modules with 8-pole M12 bus connection • 8 and 10 channel modules with 12-pole bus connection •4, 10 and 12 channel distributors with fixed cable connection, the 4 and 8 channel modules also with 4 poles It is important to note that the distributors can be labelled with the same markers as the Weidmüller 5 mm modular terminals. Therefore, no new tags have to be introduced. The modules can also be mounted sideways and are completely encapsulated. G Consequently, Weidmüller SAI distributors represent stability, robustness, flexibility and compactness - all in a single unit. M8 distributor with solder pins PCB version of a complete SAI distributor During the design of PCBs, it is often necessary to plug in different external data lines. There are a variety of connectors available for this purpose. For machine construction, the M8 and M12 connectors have become established as the standard solutions for sensor and actuator wiring. When attempting to mount these PCB-type connectors to the PCB, there is a significant risk that they will not be firmly attached to the board. Now, the SL version of the SAI distributor series solves this problem. The distributor can be completely mounted onto a PCB. It features soldering pins for the electrical connection to the PCB. The distributor itself should be slightly raised up during assembly by means of washers. This provides some clearance under the box. Naturally, the power supply channels are bridged in the distributor. This saves space on the PCB since there is no need for holes on any assembly surface. Thus the reverse side can be used for other purposes. 2001350000 – 2015/2016 G.49 M8 distributors Hooded/fixed cable version SAI-4/8-F Passive distributors SAI-4/8-M 62.2 39 13 48 SAI-4/8-M 3-pole Cable length 5 m (with fixed cable version) Cable length 10 m (with fixed cable version) 4-pole Cable length 5 m (with fixed cable version) Cable length 10 m (with fixed cable version) Note 4-channel 8-channel 4-channel 8-channel 4-channel 8-channel 4-channel 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) M8 M8 Type SAI-4-M 3P M8 SAI-8-M 3P M8 QTY 1 1 Order No. 1784680000 1784670000 Type SAI-4-F 3P M8 PUR 5M SAI-8-F 3P M8 PUR 5M SAI-4-F 3P M8 PUR 10M SAI-8-F 3P M8 PUR 10M QTY 1 1 1 1 Order No. 1784640000 1784620000 1784630000 1784610000 SAI-4-M 4P M8 SAI-8-M 4P M8 1 1 1784700000 1784690000 SAI-4-F 4P M8 PUR 5M SAI-8-F 4P M8 PUR 5M SAI-4-F 4P M8 PUR 10M SAI-8-F 4P M8 PUR 10M 1 1 1 1 1784600000 1784580000 1784590000 1784570000 Other versions on request Other versions on request Dimensioned drawing Dimensioned drawing 10...30 V 2A 2A 8A 3 IP 68 -20...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.08...1 mm² Yes br bl wh sock 1 sock 1 gr sock 2 sock 2 ye sock 3 sock 4 sock 3 gr sock 4 4-channel Ordering data 23 4-channel G Ø 4.5 4.5 73 60.356 107 pk sock 5 sock 5 sock 6 rd sock 6 sock 7 G.50 8-channel sock 8 sock 7 sock 8 vt 8-channel bl 2001350000 – 2015/2016 M8 distributors With M23/ M16 outlet SAI-8-M16 Passive distributors SAI-4/8-M23 SAI-4/8-M23 4-pole Note 8-channel 4-channel 8-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-4-M23 4P M8 SAI-8-M23 4P M8 Other versions on request QTY 1 1 M23 Order No. 1784660000 1784650000 10...30 V 2A 2A 8A 3 IP 68 -20...90 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Type SAI-8-M16 3P M8 sock 1 sock 1 sock 2 sock 2 sock 3 sock 4 sock 6 2 QTY 1 G Order No. 1795900000 J L C M F G sock 3 H sock 4 B sock 5 K sock 6 sock 5 M16 Other versions on request Dimensioned drawing Dimensioned drawing 4-way 3-pole 0[ Ordering data 2 0[ A sock 7 D sock 8 E sock 8 2001350000 – 2015/2016 8-way sock 7 G.51 M8 distributors Line SAI-5/8-S Passive distributors SAI-4/6-S 3.5 18.2 17 R4.2 9 3.2 SAI-4/6-S Ordering data Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) M12 1 1 1051760000 1932380000 5 (+) LED-GN 2k 7 8x LED-YE 8x3 k 9 sock 1 29.5 17 24 Type sock 3 SAI-8-S12 3P M8 L SAI-10-S12 3P M8 L 7 (–) 1 12 11 10 2 9 5 3 8 sock 4 4 6 4 sock 6 M12 QTY 7 sock 2 27.9 Order No. 1871680000 1877950000 1 1 Dimensioned drawing Dimensioned drawing 10...30 V 1A 2A 6A 3 IP 68 -25...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes $ Order No. 1828740000 1828730000 Other versions on request Ø 4.2 11 % QTY 1 1 SAI-4-S 3P M8 L OL SAI-6-S 3P M8 L OL sock 5 G.52 5 10-way Note 4-channel 6-channel / 8-way 3-pole without LED 4-channel 6-channel 8-channel 10-channel Type SAI-4-S 3P M8 L SAI-6-S 3P M8 L 6 8 3 6-way 3-pole 4-way G 5 3.5 13 5 / $ % 158 165 2 (-) 1 (+) sock 10 sock 9 sock 8 sock 7 sock 6 sock 5 sock 4 sock 3 sock 2 sock 1 1 9 12 10 2 3 8 4 7 6 11 5 2001350000 – 2015/2016 M8 distributors Line 1:1 Passive distributors SAI-4-S12 M8 L 1:1 SAI-4-S12 M8 L 1:1 Ordering data 3-pole Note 4-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-4-S12 M8 L 1:1 [ G QTY 2 Order No. 1449400000 Dimensioned drawing 10...30 V 1A 2A 6A 3 IP 68 -25...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes 4 3 1 BU4 4 3 12 11 10 9 8 7 6 ST1 5 4 3 2 1 1 BU3 4 3 1 BU2 4 3 1 BU1 8 9 1 10 7 12 11 2 2001350000 – 2015/2016 3 4 6 5 G.53 Passive distributors M8 distributors Line Print version SAI-6-S M8 L SL 24 118 19.7 5 17 SAI-6-S M8 L SL Ordering data Note 6-channel Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Type SAI-6-S 3P M8 L SL Other versions on request 10...30 V 1A 2A 6A 3 IP 68 -25...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes 12 11 10 7 9 5 8 6 4 3 2 (-) 1 (+) G.54 3-pole QTY 1 Order No. 1057720000 Dimensioned drawing 10-way 3-pole 8-way G sock 10 sock 9 sock 8 sock 7 sock 6 sock 5 sock 4 sock 3 sock 2 sock 1 1 9 12 10 2 3 8 4 7 6 11 5 2001350000 – 2015/2016 M8 distributors Passive distributors / 5 % $ 5 Line / Fixed cable version &KDQQHO SAI-4/6/8/10/12-L 1 1 1 1 1 1828710000 1828690000 1828670000 1828650000 1828630000 LED GN br (+) bl (–) wh sock 1 LED GN gr LED YE LED YE LED YE re re vi gr/pi sock 7 bk LED YE LED YE gr/pi re/bl wh/gn sock 9 gn re/bl sock3 ye wh/gn sock4 gr br/gn sock5 pi wh/ye sock6 re ye/br sock7 bk wh/gr sock8 vi gr/br LED YE br/gn sock 10 LED YE wh/ye sock 11 LED YE sock 12 2001350000 – 2015/2016 sock2 re/bl sock 8 LED YE LED YE wh gr/pi LED YE LED YE sock 10 bl (–) sock1 LED YE sock 6 LED YE sock 9 pi sock 5 pi sock 8 1849690000 1849670000 1828610000 gr sock 4 LED YE sock 7 ye sock 3 ye sock 6 1 1 1 LED YE LED YE sock 5 Order No. 1849680000 1849700000 1828620000 br (+) 16x LED YE gn sock 2 gn sock 4 4-pole QTY 1 1 1 G LED-GN LED YE LED YE sock 3 SAI-4-F 4P M8 L 10M SAI-6-F 4P M8 L 10M SAI-8-F 4P M8 L 10M wh sock 1 LED YE sock 2 Type SAI-4-F 4P M8 L 5M SAI-6-F 4P M8 L 5M SAI-8-F 4P M8 L 5M br (+) bl (–) ye/br 12-way 10...30 V 1A 2A 6A 3 IP 68 -25...80 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes SAI-4/6/8/10/12-L Wiring diagram Wiring diagram 4-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Order No. 1828720000 1828700000 1828680000 1828660000 1828640000 5 4-way Technical data 3-pole QTY 1 1 1 1 1 / 6-way SAI-4-F 3P M8 L 10M SAI-6-F 3P M8 L 10M SAI-8-F 3P M8 L 10M SAI-10-F 3P M8 L 10M SAI-12-F 3P M8 L 10M 6-way Note 4-channel 6-channel 8-channel 10-channel 12-channel 8-way Cable length 10 m (with fixed cable version) 4-channel 6-channel 8-channel 10-channel 12-channel Type SAI-4-F 3P M8 L 5M SAI-6-F 3P M8 L 5M SAI-8-F 3P M8 L 5M SAI-10-F 3P M8 L 5M SAI-12-F 3P M8 L 5M 10-way Cable length 5 m (with fixed cable version) % 8-way Ordering data $ G.55 Passive distributors M5 distributors Overview M5-Line with M12 outlet The Weidmüller SAI-M5 distributors are currently the smallest SAI distributors in the world Whether it is mobile phones or computers, as functionality increases, so the size of components decreases. Today, machine designers face the same problem. Space is at a premium, even in large machines, particularly where the sensor components are located. In the past the M8 distributor solved these problems. However, these units are now considered to be too large. The first move was to make the sensors smaller. Then it was the turn of the cables and distributors. These extremely small units are surprisingly easy to handle. M5 plug in connectors have three or four poles and are thus equivalent to M8 plug-in connectors. G Fixed cable version M5-Line with M16 outlet However, unlike the M8 plug in connectors, the different M5 pole numbers are compatible with each other. The advantage is obvious: 4 pole units which are required, for example, for antivalent sensors can now be plugged into one and the same distributor with standard NOC applications. In the M8 system special adapters are required. In addition to size, the module weight is also critical in some applications. For example, the speed of a handling machine is influenced by the weight of the moving parts. The M5 system offers outstanding benefits with its unrivalled small size and light weight. There is no version for custom bus cable assembly for this SAI distributor, which is delivered with a plug in connection and a fixed cable connection. A compact 12 pole M12 plug in connector has been developed as a plug in connection specifically for this distributor. This ratio of surface area to number of connections is reminiscent of the computer industry. The M16 bus connections can be integrated in the module as an option, so that the SAI M5 can be used as a combined SAI system. A Y-configuration is possible in conjunction with the M16 splitter. The fixed cable version is particularly suitable for standard applications where the distributor is permanently installed and the electrical installation does not have to be disconnected after installation. G.56 2001350000 – 2015/2016 Passive distributors M5 distributors MM5 distributors Quality comes in little packages… This is the motto applied by Weidmüller when developing its M5 plug in connectors. The outstanding feature of these connectors is their tiny size. Attention has also been given to stability and good conductivity. For a comparison of sizes, take a look at the photos on the left. These products are ideal for handling machines where light weight and small size are vital. Comparing the sizes Marking Each channel is marked with the channel number. Each initiator LED can be exactly allocated with the letters A and B. In addition, the distributor and every channel can be marked. G M12M8 M5 M12M8 M5 2001350000 – 2015/2016 G.57 M5 distributors Line SAI-4/8-S Passive distributors SAI-4/8-F 23.5 20 12 9.5 12 34 34 M12 16.7 20 13 B A B A 69 69 3 A B 3 4 A 4 9.5 12 13 13 14 SAI-4/8-F Ordering data 4-pole Cable length 5 m (with fixed cable version) Cable length 10 m (with fixed cable version) Note 4-channel 8-channel 4-channel 8-channel Order No. 1851740000 1851760000 1845820000 1845830000 Type SAI-8-S 3P M5 1 1845850000 4-channel 8-channel 4-channel 8-channel SAI-4-F 4P M5 L5M SAI-8-F 4P M5 L5M SAI-4-F 4P M5 L10M SAI-8-F 4P M5 L10M 1 1 1 1 1851770000 1851750000 1845800000 1845810000 SAI-4-S 4P M5 1 1845840000 Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Other versions on request Other versions on request 1 br (+) LED-GN LED gn bl (–) 8 x LED-YE sock 1 Order No. Dimensioned drawing Dimensioned drawing 10...30 V 1A 3A 3A 3 IP 67 -25...80 °C PA 6 GF Nickel-plated CuZn CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... Yes QTY M5 QTY 1 1 1 1 2k 7 wh 2 8 x LED ye 8 x 3k 9 sock 1 3 5 sock 2 gn 4 sock 2 9 sock 3 ye 6 sock 3 4-way Cable length 10 m (with fixed cable version) M5 Type SAI-4-F 3P M5 L5M SAI-8-F 3P M5 L5M SAI-4-F 3P M5 L10M SAI-8-F 3P M5 L10M 7 sock 4 gr sock 5 pi sock 6 re sock 7 bk sock 8 vi 4-way 3-pole Cable length 5 m (with fixed cable version) G.58 2 B 2 8 sock 4 10 1 9 12 8 7 6 11 10 8-way G A A 76 10 A A B 1 B B A 10 76 1 B 5 3 4 2001350000 – 2015/2016 M5 distributors Line Passive distributors SAI-4/8-S16 22.57 16.7 20 13 B 1 B B 3 A B 4 A B 5 A B 6 A B 7 A B A 109 2 A 116 10 A 8 A 12 13 SAI-4/8-S16 Ordering data 4-pole Note 4-channel 8-channel Type SAI-4-S16 3P M5 SAI-8-S16 3P M5 4-channel 8-channel SAI-4-S16 4P M5 SAI-8-S16/19P 4P M5 Technical data Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) QTY 1 1 Order No. 1845890000 1845880000 1 1 1845870000 1845860000 G 1845870000,1845880000 and 1845890000 with M16 / 12-pole 1845860000 with M16 / 19-pole Dimensioned drawing 10...30 V 1A 3A 3A 3 IP 67 -25...80 °C PA 6 GF Nickel-plated CuZn CuZn CuZn, nickel-plated grey, RAL 7032 V-0 ... LED-GN 2k 7 sock 1 8 x LED-YE 8 x 3k 9 sock 2 sock 3 sock 4 4-way 3-pole M5 sock 5 sock 6 sock 8 2001350000 – 2015/2016 8-way sock 7 G.59 Passive distributors M12 Ex i distributors SAI Ex i distributor for Ex i zone 1 Hooded version with 4 plug-in slots SAI distributor for Ex i zone 1 Available for the first time: passive SAI distributors with M12 connection technology in IP 68 ingress protection classification for Ex i hazardous area applications. The SAI Ex i distributor is certified for zone 1 of potentially explosive areas, even for G and D zones. SAI Ex i distributors are available with four or eight connections for simple connection of NAMUR sensors. This makes distribution boxes with certification a thing of the past. These modules are suitable for process engineering, but also for “standard” machine applications. The versions are available with or without yellow LEDs. G G.60 Hooded version with 8 plug-in slots The distributors are provided with a removable connection hood. This detail also helps to reduce costs because only the defective bus cable needs to be replaced and not the entire distributor. 2001350000 – 2015/2016 M12 Ex i-distributors 6$,0 6$,0 6$,0 SAI-4/8-M Ex i Ordering data Complete modules Without initiator LED Without initiator LED Note 4-channel 6-channel 8-channel 4-channel 8-channel 4-pole Type SAI-4-M 4P Exi Z1 IL QTY 1 Order No. 1868360000 SAI-8-M 4P Exi Z1 IL SAI-4-M 4P Exi Z1 OL SAI-8-M 4P Exi Z1 OL 1 1 1 1868370000 1868350000 1894380000 Passive distributors Hood version SAI-4/8-M Ex ia Type SAI-4-M 5P M12 Ex ia SAI-6-M 5P M12 Ex ia SAI-8-M 5P M12 Ex ia QTY 1 1 1 5-pole Order No. 1896050000 1896070000 1896090000 G blue 8-way red sock 8 sock 7 sock 6 sock 5 4-way 10...30 V 100 mA 100 mA 2.3 A 3 IP 68 -20...40 °C Pocan PBT (UL 94 V0) CuZn CuZn, nickel-plated grey, RAL 7032 V-0 0.1...1.5 mm² 4-way Operating voltage Current of continuous busbars Max. current-carrying capacity per slot Total current Pollution severity Protection degree Ambient temperature range Housing main material Contact carrier material Base material of contacts Screw socket Housing colour Flammability class UL 94 Clamping range of hood-version Suitable for dragline cable (fixed cable connection) Wiring diagram Wiring diagram sock 4 sock 3 6-way Technical data 8-way sock 2 sock 1 2001350000 – 2015/2016 G.61 Passive distributors G G.62 2001350000 – 2015/2016