Download

Opto Modules and Solid-State Relays
Product Information
Opto Modules and Solid-State Relays
Optos – Overview
Definition / mode of operation
4
Basic functions
6
Control / load circuit
7
Switching amplification / protective measures
9
Product versions
12
Product families
14
Terminology explained
16
Technical data definition
18
Optos – MICROSERIES
Optos 3....48 V DC / 0.1 A
19
Solid-state relays 24...240 V AC / 1A
20
Solid-state relays 3...33 V DC / 2 A
21
Solid-state relays, actuator version
22
Pluggable solid-state relays
23
Accessories
24
Optos – MICROOPTO
Optos 12...28 V DC / 100 kHz
25
Solid-state relays, actuator 24 V DC / 2A
26
Solid-state relays 300 V DC / 1A
27
Optos – MCZ-SERIES
Optos MiniConditioner MCZ O
28
Optos MCZ O TRAK
31
Accessories
32
PLUGSERIES
Solid-state relays up to 30 V DC / 5A
34
Solid-state relays up to 275 V AC / 4 A
35
Solid-state relays up to 30 V UC / 1 A
36
Accessories
37
RSO-SERIES
38
Worldwide activities
40
Optos – Overview
Definition / mode of operation
Optocouplers – mode of operation
Optocouplers are electronic components for switching load
circuits by means of a control circuit. On the one hand this
allows applications with different performance ratings to be
operated by relatively low switching currents. And on the
other electrical isolation *) between control and load circuits
is provided to assure protection of components should a
malfunction occur.
In contrast to electromechanical relays optocouplers do not
have any mechanical parts that are prone to wear. To enable
the switching operation a light signal is triggered via an LED in
the control circuit that causes a light-sensitive semiconductor
receiver to complete a connected load circuit.
Transmitter (LED) and receiver (for example a phototransistor) are embedded in a light conducting plastic material and
­encased in a light-proof casing that protects against outside
influences.
Transmitter
(LED)
Receiver
(Transistor)
Control circuit
Load circuit
Face-to-face
Coplanar
Transmitter (LED)
Two design types are differentiated:
Face-to-face design with LED and transistor mounted across
from each other with direct light contact
Coplanar design with LED and transistor on the same level. In
this case the beam of light is transferred by reflection according
to the principle of fibre-optics.
Transmitter
(LED)
Receiver
(Transistor)
Receiver
(Transistor)
Opto module
Opto module
The voltage, which can be applied to the opto output ­itself,
is restricted by the sensitivity of the semiconductor ­receiver
(phototransistor). In applications in which only low ­currents or
voltages are required in the load circuit it is possible to use the
component without an additional auxiliary circuit in an opto
module.
Control circuit
Load circuit
Optocoupler
Solid-state relay
In order to switch higher currents it is necessary to make
­adaptations to accommodate the different performance levels of
the phototransistor and the load circuit (switching amplification).
Modules other than optos equipped with a switching amplifier
are called solid-state relays (SSR).
Switching amplification
Solid-state relay
Control circuit
Optocoupler
*) Please refer to pages 16-17 for a detailed explanation of the term
Load circuit
Optos – Overview
Depending on the requirements, the choice between electromechanical and solid-state relays is made based on the different
advantages that the different versions offer:
Movable contact
Housing
Receiver
(Transistor)
Armature
Fixed contacts
Transmitter (LED)
Reset
spring
Coil
Advantages of solid-state relays (SSR)
Advantages of electromechanical relays (EMR)
+ Long operational lifetime and reliability
No moving parts or contact wear
+ AC and DC operation in load circuit possible
Versatile (advantage as interface between different
plant equipment)
+ Small dimensions
Saves space on the PCB and mounting rail
+ Low control power
An LED is activated - no mechanical parts are moved
+ Fast response times
Fast switching, which allows high frequencies to be
achieved
+ No contact bounce
Reduces switching delays
+ No switching noise
Suitable for use in noise-sensitive environments
+ Not susceptible to shock and vibration
Prevents unwanted switching statuses
+ No electromagnetic radiation due to switching sparks or coils
No interference of adjacent assemblies or electronics
components
+ No leakage current in the load circuit
A semi-conductor does not achieve 100% isolation
+ Low residual voltage in the load circuit
Low voltage drop
+ No power loss in the load circuit
In contrast to the semi-conductor in optos there is no
electrical resistance in the contacts of the electromechanical relays that can lead to a rise in ­temperature
when under load. Therefore, heat sinks are not necessary.
+ Multiple contacts possible
A single control signal can switch several load circuits
+ Control circuit less sensitive to transients *)
Unwanted switching operations caused by voltage
fluctuations are prevented by the make capacity of the
magnetic coil.
*) Please refer to pages 16-17 for a detailed explanation of the term
Optos – Overview
Basic functions
Opto modules and solid-state relays are generally used in the
following fields of applications:
Potential isolation
Many applications require that the control circuit is electrically
isolated from the load circuit. This primarily protects the control
level from interference from the field, such as:
Potential isolation
Test
voltage
min. 2.5 kV
- Interference currents e.g. from earth and ground loops *)
- Interference pulses e.g. from inductive effects of transients *)
Clearance and creepage distance
min. 3 mm
The separation of the control and load circuits in the ­opto provides the required isolation.
However, this must withstand an isolation test of at least 2.5 kV
in all opto modules and solid-state relays. To guarantee isolation
it is necessary that a minimum 3-mm clearance and creepage
distance *) be maintained in all components.
Signal conditioning
The separation of the load and control circuits in conjunction
with the variety of options this offers to configure both circuits
separately means that optos are often used for signal conditioning purposes.
This allows the different electrical potentials of signals from the
control and load circuits (for example sensors and control) to be
equalised.
Signal conditioning
120 V AC
Switching amplification
Applications with current and voltage values that exceed the
capacity of the phototransistor require an auxiliary circuit on the
output side of the opto for switching amplification ­purposes.
During the switching operation the opto LED activates a base
current in the phototransistor. This activates a second semiconductor (transistor, tyristor) selected to meet application requirements which then becomes conductive for the load ­current.
*) Please refer to pages 16-17 for a detailed explanation of the term
24 V DC
Optos – Overview
Control circuit
Auxiliary circuit
Control circuit
Voltage regulation
Most industrial application cannot be connected directly to an
opto, generally requiring voltage regulation by means of seriesconnected resistances or capacitors.
To obtain exact-as-possible switching points a Schmitt Trigger
can be used to assign the control signals an unambiguous
­status (0 - 1) when moving from high to low or low to high,
which is then passed on to the opto.
Input configuration
Protective circuit
The input circuits (control circuit)
Depending on the design, all Weidmüller opto modules and
solid-state relays are equipped with suitable protective devices
(varistors, diodes) and filters to protect against ­interference
pulses from the control circuit.
DC input:
An additional reverse-polarity protection diode guarantees protection against the opto being destroyed if the control voltage
is incorrectly wired. The switching status of the control circuit is
signalised by a status indicator.
AC/DC input:
A rectifier with smoothing capacitor is connected in series for
AC control voltages. Reverse polarity protection for DC current
is not necessary. The following construction corresponds to a
DC circuit.
Due to the smoothing capacitor the switching frequency of
AC control signals is fundamentally less than half the mains
­frequency. A higher switching frequency would result in the
­control signal being constantly switched through in rhythm with
the mains frequency.
The advantage of being able to choose between an AC or a DC
current input contrasts with the disadvantage that the smoothing capacitor also restricts the switching frequency of the DC
control signal.
DC input
Control circuit
AC/DC input
Control circuit
AC input
AC input:
The circuit diagram corresponds in principle with an AC/DC
circuit. Instead of series resistors it is possible to use capacitors
to regulate the voltage in a purely AC operation. In contrast to
resistors there is no power loss with capacitors and as a result
no heat that needs to be dissipated.
Control circuit
*) Please refer to pages 16-17 for a detailed explanation of the term
Optos – Overview
Load circuit
Protective circuit
Interface circuit
Protective circuit
Load circuit
Protective circuit
Load circuit
Protective circuit
Load circuit
Interface circuit
Load circuit
Interface circuit
As a rule, an operating voltage range is stated for the rated
switching voltage of opto modules and solid state relays (for
example 5 ... 48 V DC); it is not permitted to exceed or fall
below this value.
The same applies to continuous current. Exceeding this value
to often can result in premature wear-out and destruction of the
optos semiconductor.
As a direct correlation exists between the current and ambient
temperature a derating curve *) is provided for all opto modules
and solid-state relays.
Overvoltages are shunted by protective devices such as diodes
or varistors.
To prevent damage caused by current spikes (for example starting or off pulses) some modules are equipped with a power
boost which is capable of carrying higher levels of current than
the maximum stated for a short period of time.
2-wire DC output
It is possible to connect AC or DC loads subject to the output
circuit having corresponding amplifier semiconductors.
DC output:
With a 2-pole DC output the connection terminals are to be
considered in the same manner as with a conventional switch.
All that is required is that care is taken to observe the predetermined polarity.
3-wire DC output
With a 3-pole DC connection an auxiliary voltage assists the
output circuit to control the amplifying transistor more precisely.
Several applications also require this auxiliary voltage for shortcircuit protection in the interface or protective circuitry.
AC output:
To activate AC switching and control devices a semiconductor
is connected on the load side of the opto component to switch
the AC voltage (TRIAC or tyristor).
Switching amplification
Output circuit
Interface circuit
The output circuit (load circuit)
AC output
*) Please refer to pages 16-17 for a detailed explanation of the term
Out
Optos – Overview
Switching amplification
The phototransistor of the opto has a low current and voltage
rating. As a consequence, an additional semiconductor element
is accessed for larger output loads that is capable of switching
the corresponding rated switching voltages and rated switching
currents.
Bipolar Transistor (DC)
Used for low currents (0.5 A).
The bipolar transistor has short response times, which makes
high switching frequencies possible as a result.
Switching amplification
Transistor
MOSFET
TRIAC
MOSFET (DC)
Used for high load currents (up to 10 A).
The low contact resistance of the MOSFET create only very
small leakage currents (< 10 µA) with low power loss.
TRIAC (AC)
A TRIAC combines the functional principle of antiparallel
­connected tyristors in a single component.
The mode of function of a tyristor is comparable with that
of a one-way diode. Therefore, an opposing parallel circuit
­configuration consisting of two tyristors is used for AC currents.
*) Please refer to pages 16-17 for a detailed explanation of the term
Optos – Overview
Switching diverse loads
The different types of loads resulting from the possible applications (resistive, inductive, capacitive loads) represent a particular
challenge for the load circuit arrangements of opto ­modules and
solid-state relays. With reference to the planned application,
one should always be aware of what effects the loads will have
on the modules and how the corresponding ­protective devices
have to be designed.
Generally speaking, it must be ensured that the power loss at
the amplifier semiconductor does not exceed the permitted limit
for any length of time. This would lead to overheating and finally
to the destruction of the component.
Switching capacitive loads
Capacitive loads occur if there is a capacitor in the load circuit.
The effect is similar to to a short-circuit at the point of activation
and results in a high inrush current.
If this current is not limited it can lead to the destruction of the
amplifier semiconductor.
Switching on
­capacitive loads
Amperage
Switching resistive loads
Due to the fact that in resistive loads the amperage in the load
circuit and the voltage across the amplifier semiconductor
are inversely proportional to one another these do not generally pose a problem. It is sufficient to adhere to the maximum
­current and voltage ratings of the modules.
Switching glow lamps represents a special case. It is possible
that when being switched on that overcurrents 10 to 20 times
the operating current can occur due to the low cold resistance.
Therefore, the components must be designed to cope with
these possible overloads situations which correspond to the
­effect of capacitive loads.
Operating current
0A
Switching inductive loads
Problems can arise with inductive loads when they are being
switched off, in particular when coils are used in the load
circuit. The flow of current in the coil builds up a magnetic field
that suddenly collapses and creates a high induction voltage.
This voltage spike has to be short-circuited via a diode
­connected in parallel (free-wheeling diode). However, the time
­required leads to delayed release.
Turning off
inductive loads
Operating voltage
0A
Switch-off point
*) Please refer to pages 16-17 for a detailed explanation of the term
10
Time
Voltage
Switch-on point
Time
Optos – Overview
Protective measures
The construction of the opto enables fast and sensitive switching, however, the component is also more prone to interference.
For this reason, all Weidmüller opto modules and solid-state relays are equipped with a variety of measures to protect against
overloading and interference pulses.
Free-wheeling diodes (DC)
Free-wheeling diodes are used primarily to protect against overvoltages, which occur through self-induction when switching off
inductive DC loads (electric motors, relay coils).
Voltage spikes are limited to the equivalent value of the diode
forward voltage and excess voltage is discharged via the diode.
However, this leads to a delay in the voltage drop and as such
also delays the switching operation.
Protective measures
Zener diode
Suppressor diode
Free-wheeling
diode
RC element
Varistor
Zener diode / suppressor diode (DC)
These function as normal diodes in the forward conducting
­direction. In the blocking direction they become low resistant at
a certain voltage (breakdown voltage).
High levels of overvoltages can lead to the destruction of the
zener diode / suppressor diode.
Varistor (AC/DC)
The functional principle of the varistor is also based on a breakdown voltage, but with faster reaction times. This allows higher
levels of energy to be shunted, however, these lead to the
­component aging. This in turn reduces the breakdown voltage
over time and increases the leakage current.
RC-element (AC)
The RC element compensates voltage spikes by means of a
capacitor. Due to the charging and discharging characteristics
interference pulses are filtered out when the voltage is rising
and not first when overload is reached.
For this reason, RC elements are used to protect against interference pulses and exclude faulty switching operations.
*) Please refer to pages 16-17 for a detailed explanation of the term
11
Optos – Overview
Product versions
The essential advantages of optos in comparison with electromagnetic relays are primarily to be seen in their characteristics:
- Less sensitive to vibration and oscillation
-Longer operational lifetime with regard to load circuit
­demands
- Fast switching speeds
In order to make use of these characteristics in industrial
­applications suitable additional circuits are necessary on the
load and control side. Therefore, with Weidmüller opto modules
and solid-state relays the focus is placed firmly on the development of products that are tailored exactly to meet the requirements of typical applications.
The result is a palette of products to suit all application
­requirements:
Standard applications
For example potential
isolation
Conveyor belt
Sensor
Power supply
24 V DC
Power supply
24 V DC
(24 V DC)
Control
Standard applications
In many industrial applications it is sufficient to utilise an opto
for potential isolation and signal conditioning purposes.
For these requirements Weidmüller offers opto modules from
the MICROSERIES and MCZ-SERIES product ranges.
The integrated suppressor circuits guarantee sufficient
­protection for applications with resistive loads as well as light
inductive and capacitive loads.
With purely inductive, capacitive or comparable loads such
as solenoid valves or glow lamps with high making or breaking spikes it must be ensured that the module is sufficiently
­dimensioned or an additional protective device taken into
­consideration.
Fast switching
Fast signal transmission is one of the advantages of optos,
which makes it possible to achieve high frequencies.
Interior circuit elements in the opto module ­MICROOPTO
100 kHz ensure that rapidly transmitted signals are isolated
from one another and that they can be transferred practically
without delay. This allows switching frequencies up to 100 kHz
to be achieved.
12
(120 V UC)
For example signal conditioning
230 V AC
PE N L
(230 V AC)
(24 V DC)
Power supply
24 V DC
Lamp
(120 V UC)
For example rotational
speed measurement
Sensor
Power supply
(230 V AC)
Power
supply
Control
Optos – Overview
Special loads
Weidmüller not only offers a product assortment for standard applications but also offers opto solutions for special
­applications.
Interface circuits, switching amplification and protective ­circuits
are specifically adapted to meet the requirements of the
­corresponding applications.
The solid-state relay MICROOPTO ACTOR has been
­especially designed as a switching amplifier for actuators up
to 24 V DC and 2A with inductive loads such as solenoid
valves and contactors. 3-wire actuators can be connected
directly to the module.
This is short-circuit proof and protected against application­related transients and spikes by extensive protective circuitry.
For example solenoid valve
bar
PE
Valve
Power supply
Control
PE
The solid-state relay MICROOPTO 300 V DC has been developed as a switching amplifier for high inductive loads up to
300 V DC and 1 A in motor brakes and contactors.
A power boost in the load circuit compensates transient overloads (20 A for 20 ms / 5 A for 1 s) such as making or breaking
spikes. Additional protective circuits counter higher overloads.
For example motor brake
Power supply
Control
All Weidmüller produced opto modules and solid-state relays
undergo a function and dielectric test.
This guarantees 100% functional performance and that the
control and load circuits are safely isolated from one another.
13
Optos – Overview
Product families
MICROOPTO
The MICROOPTO range of products provide the user with the
tried and tested characteristics of terminal blocks. Pluggable
cross-connections and ­harmonised marking solutions packaged
in a minimum design width.
Best performance within a small footprint.
• 6.1 mm design width
• Pluggable standard cross-connection ZQV 4N
• Suitable for labelling with MultiCard system
• Snap onto TS 35 mounting rails
•Housing material made of WEMID (higher thermal stability in
comparison with polyamide)
MICROSERIES
The MICROSERIES offers the same product features as the
­MICROOPTO range.
In addition, the opto components and solid-state ­relays are also
designed as pluggable modules for a base with ­integrated connection system. The screw and tension clamp connection offers
free choice of connection systems.
The plug-in module can be replaced without having to
­disconnect the connections. It is also possible to exchange
solid-state relays for electromechanical relays.
MCZ-SERIES
With a design width of just 6 mm the MCZ housing is the
­slimmest of its kind and is distinguished by the following
­technical characteristics:
• 6 mm design width
•Tension clamp connection with reduced installation costs
•Terminal cross-sections up to 1.5 mm2
• Integrated cross-connection in input/output
• Pluggable cross-connection
• Snap onto TS 35 mounting rails
• Version available designed for use in railway applications
•Housing material made of WEMID (higher thermal stability in
comparison with polyamide)
14
Optos – Overview
PLUGSERIES
The basis of the PLUGSERIES is a base designed to mount
onto mounting rails and contact plug-in electromechanical and
solid-state relays.
The plug-in module can be replaced without having to
­disconnect the connections. It is also possible to exchange
solid-state relays for electromechanical relays.
• Pluggable standard cross-connection ZQV 2.5N
• Screw or tension clamp connection
• Terminal cross-sections up to 2.5 mm2
• Suitable for labelling with MultiCard system
• Snap onto TS 35 mounting rails
•Housing material made of WEMID (higher thermal stability in
comparison with polyamide)
RSO SERIES
Most compact and value-for-money solution available to
­implement solid-state relays for installing on mounting rails.
Commercially available solid-state relays with appropriate
­terminals are soldered to the PCB. It is fixed to the mounting rail
by means of a plastic base.
• Screw connection
• Terminal cross-sections up to 2.5 mm2
• Snap onto TS 35 mounting rails
15
Optos – Overview
Derating curve
Current flow generates heat that also rises with increasing
­amperage.
Electrical components have a defined upper limit temperature to
which the functional performance is restricted. The temperature
influencing the components is a combination of the ambient
temperature and the heat generated by the current, so to ensure that the limit temperature is not exceeded the current must
be reduced when the overall temperature rises.
The derating curve depicts this relationship between the
­prevailing temperature and the resulting maximum amperage
with regard to the limit temperature.
Earth and ground loops
Denote the connection of two potentials via their earth or
ground connection.
A potential difference between the earth or ground connection
of two devices (for example sensor and control) that are directly
wired to one another causes current flow over the earth or the
common housing. These interference currents can lead to different problems, for example in the acquisition of measurement
signals or when activating actuators.
Transmitting switching or measurement signals using a device
with electrical isolation between the control and load circuits
means that a closed circuit via the earth or ground connection
can never occur - and consequently no interference currents
are generated.
Clearance and creepage distances
Clearance and creepage distances are decisive factors with
­regard to the isolation capability of electrical components.
The creepage distance denotes the minimum clearance two live
parts along a surface must have in order to prohibit a flow of
current across the insulating material at the denoted operating
voltage.
In addition to the operating voltage, the choice of insulating material (insulating material group) as well as protective measures
to counteract pollution (pollution severity) affect the creepage
distance.
The clearance distance denotes the minimum direct clearance
(through the air) that two live parts must have to one another
in order to prohibit a charge flow through the air (arc). The expected overvoltage (rated impulse voltage) forms the basis for
calculating the distances. The surge protection category and
pollution severity are further factors that influence dimensional
design considerations.
16
Derating curve
Amperage
Terminology explained
Forbidden area
Operating area
Temperature
Earth and ground loops
Connecting
element without electrical
­isolation
Connecting ­element
with electrical
­isolation
Clearance
distance
Housing contour
Creepage
distance
Current carrying parts
Optos – Overview
Electrical isolation
Electrical isolation is defined as when there is no possibility for a
charge carrier to flow from one circuit to another.
Consequently, there is no electrically conductive connection
between the circuits.
Nevertheless, it is possible for the circuits to exchange ­electrical
power or signals. In such cases transmission is achieved
via magnetic fields, by means of infrared radiation or charge
­transfer.
Schmitt Trigger
Strictly speaking, switching voltages for digital control follow an
analogue pattern (no 0 – 1 between maximum and minimum
voltage). This can lead to inaccuracies in switching behaviour,
above all when signals are being transmitted rapidly.
In this case the Schmitt Trigger takes on the function of a
threshold switch. If the threshold voltage set in the Schmitt
Trigger is exceeded the output assumes the maximum possible
output voltage (logic 1); in the other case is assumes the minimum possible output voltage (logic 0).
The Schmitt Trigger is generally designed with a hysteresis.
A higher threshold voltage is set for activating than deactivating.
That prevents small irregularities triggering a switching operation.
Schmitt-Trigger
Current
Input signal
Activate threshold
Deactivate threshold
Hysteresis
Time
Strom
Signal conditioning
through Schmitt Trigger
Time
Transients
Transients are current or voltage spikes of short duration that
are caused by interferences in the supply circuit or by electromagnetic radiation.
On the control side of the opto these can trigger unintended
switching operations or, in extreme cases, cause the destruction of the component.
In an AC driven load circuit transients can lead to the maximum
permissible forward voltage being exceeded, which in turn can
activate the tyristor or TRIAC. As these operate at quite high
switching speeds, even very short pulses can suffice to falsely
trigger a switching operation.
Transients
Voltage
Overvoltage
Max. forward voltage of
tyristor
Time
Example:
Fault in the AC circuit
Current
Current at output
Time
17
Optos – Overview
Technical data
Definition of the technical data listed on the following
­product selection pages:
Rated and limit values for load circuits
Rated voltages
Rated switching voltage
Voltage value that defines the application of the load circuit and to which the relevant tests and load
categories refer.
Voltage drop (at max. load)
Highest voltage value between the connections when switched through.
Rated voltage (insulation)
Voltage value to which the dielectric tests and creepage distances refer.
Rated impulse voltage
Peak value of the voltage pulse with prescribed form and polarity that the solid-state relay can
­withstand under specified test circumstances without failing, and to which the clearance distance
­values refer.
Rated currents Rated switching current
If not otherwise stated, operating current when switched through taking into consideration the rated
voltage, the rated frequency, the load category and overcurrent characteristics at 40 °C ambient
temperature.
Continuous current
Value of current that the module can carry continuously
Leakage current
rms value of the current that flows through the switching element when in the off state
Mains frequency
Mains frequency for which the module was developed and to which the other characteristic values
­correspond
Permissible short-circuit current
Value of the current that the module can carry when protected by short-circuit protection device
­specified by the manufacturer
Load category to DIN EN 62314
LC
LC
LC
LC
LC
LC
A: Resistive or low inductive loads
B: Motor loads
C: Gas discharge lamp
D: Glow lamps
E: Transformers
F: Capacitive loads
Rated and limit values for control circuits
Rated power
Product of rated voltage and rated current; this is the minimum that must be made available to the
assembly group being driven
Max. input frequency
Maximum signal frequency value with which it is permitted to apply the control voltage
Rated control voltage
Voltage value for which the control circuit is defined
Rated auxiliary voltage
Value of the auxiliary voltage that must be made available to the coupler
Making voltage
Voltage value at which the load circuit will reliably switch through
Breaking voltage
Voltage value at which the load circuit reliably disables
Switch-on delay
Time from applying the rated control voltage until the load circuit is fully enabled
Switch-off delay
Time from opening the rated control voltage until the load circuit is fully disabled
Ambient temperature
Temperature range of the surrounding air for which the module is rated
Storage temperature
Temperature range of the surrounding air at which the module can be stored
18
Optos – MICROSERIES
MOS / MOZ 3...48 V DC / 0,1 A
Universal interface between control and sensor/actuator
• Plug-in cross-connection ZQV 4N
• Interchangeable solid-state relay
• 6.1 mm wide
• Screw or tension clamp connection
• For mounting on TS 35
(24 V DC)
(120 V UC)
(230 V AC)
Output Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Leakage current
Short-circuit-proof/Protective circuit
General data Operating temperature
Storage temperature
3…48 V DC
0.1 A
≤1V
≤ 1 mA
≤ 1 mA
no/Integrated free-wheel diode
-25 °C…+50 °C
-40 °C…+60 °C
Approvals
Insulation coordination (EN 50 178) Standards
CE; cULus;
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.) mm2
Length x width x height
mm
300 V
4.0 kV
≥ 5.5 mm
III
2
Note
EN 50178
Screw connection
2.5 / 0.5 / 4
93 / 6.1 / 92
Tension clamp connection
1.5 / 0.5 / 2.5
94 / 6.1 / 91
CE, UL/UR
for mounting on TS 35
Ordering data
5 V DC / 24 V DC 0.1 A
24 V DC / 24 V DC 0.1 A
120 V UC / 24 V DC 0.1 A
230 V AC / 24 V DC 0.1 A
Input
Rated voltage
Rated current
Power rating
max. input frequency
Switch-on delay
Switch-off delay
5 V DC ±20%
11 mA ±10 %
55 mW ±10 %
10 Hz
< 6,5 ms
< 10 ms
24 V DC ±20 %
5,7 mA
140 mW
300 Hz
35µs
355µs
120 V UC + 10 %/ -15 %
3,4mA AC/2,8mA DC
340 mW / 0.4 VA
DC: 10 Hz /AC: 3 Hz
< 6.5 ms
< 10 ms
230 V AC ±10%
7.4mA
1.7 VA
3 Hz
< 6.5 ms
< 10 ms
MOS 5Vdc / 24Vdc 0,1A
MOS 24Vdc / 24Vdc 0.1A
MOS 120Vuc / 24Vdc 0.1A
MOS 230Vac / 24Vdc 0.1A
8633020000
8607340000
8607690000
8607710000
MOZ 5Vdc / 24Vdc 0.1A
MOZ 24Vdc / 24Vdc 0,1A
MOZ 120Vuc / 24Vdc 0.1A
MOZ 230Vac / 24Vdc 0.1A
8633010000
8607360000
8607730000
8607750000
SSS Relais 5V/24V 0,1ADC
SSS Relais 24V/24V 0,1Adc
SSS Relais 60V/24V 0,1Adc
SSS Relais 24V/24V 0,1Adc
4064320000
4061180000
4061230000
4061180000
Ordering data
Complete module
Screw connection
Type
Order No.
Tension clamp connection
Type
Order No.
Ordering data
Spare relay, pluggable
Type
Order No.
Note
19
Solid-State Relays – MICROSERIES
MOS / MOZ 24...240 V AC / 1 A
Universal interface between control and sensor/actuator
• Plug-in cross-connection ZQV 4N
• Interchangeable solid-state relay
• 6.1 mm wide
• Screw or tension clamp connection
• For mounting on TS 35
(24 V DC)
(120 V UC)
(230 V AC)
Output Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Leakage current
Short-circuit-proof/Protective circuit
General data Operating temperature
Storage temperature
24…240 V AC
1A
approx. 1.6 V
approx. 1.5 mA at 200 V
≤ 20 µA
no/Integrated free-wheel diode
-25 °C…+50 °C
-40 °C…+60 °C
Approvals
Insulation coordination (EN 50 178) Standards
CE; cULus;
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.) mm2
Length x width x height
mm
300 V
4.0 kV
≥ 5.5 mm
III
2
Note
CE, UL/UR
for mounting on TS 35
EN 50178
Screw connection
2.5 / 0.5 / 4
93 / 6.1 / 92
Ordering data
24 V DC / 230 V AC 1 A
120 V UC / 230 V AC 1 A
230 V AC / 230 V AC 1 A
Input
Rated voltage
Rated current
Power rating
max. input frequency
Switch-on delay
Switch-off delay
24 V DC ±20 %
10.4 mA ± 10%
250 mW ± 15 %
3 Hz
< 11 ms
< 11 ms
120 V UC + 10 %/ -15 %
2.5…3.8 mA
0.4 VA ±15%
3 Hz
< 11 ms
< 11 ms
230 V UC ±10 %
7.4 mA ±10 %
1,7 VA ± 20%
3 Hz
< 20 ms
< 20 ms
MOS 24Vdc/ 230VAC 1A
MOS 120Vuc / 230VAC 1A
MOS 230Vuc/ 230Vac 1A
8652010000
8651930000
8651990000
MOZ 24Vdc/ 230VAC 1A
MOZ 120Vuc / 230VAC 1A
MOZ 230Vuc/ 230VAC 1A
8652020000
8651950000
8651970000
SSS Relais 24V/230V 1Aac
SSS Relais 60V/230V 1Aac
SSS Relais 24V/230V 1Aac
4061210000
4061220000
4061210000
Ordering data
Complete module
Screw connection
Type
Order No.
Tension clamp connection
Type
Order No.
Ordering data
Spare relay, pluggable
Type
Order No.
Note
20
Tension clamp connection
1.5 / 0.5 / 2.5
94 / 6.1 / 91
Solid-State Relays – MICROSERIES
MOS / MOZ 3...33 V DC / 2 A
Universal interface between control and sensor/actuator
• Plug-in cross-connection ZQV 4N
• Interchangeable solid-state relay
• 6.1 mm wide
• Screw or tension clamp connection
• For mounting on TS 35
(24 V DC)
(120 V UC)
(230 V AC)
Output Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Leakage current
Short-circuit-proof/Protective circuit
General data Operating temperature
Storage temperature
3…33 V DC
2A
≤ 120 mV
approx. 10 µA
≤ 1 mA
no/Integrated free-wheel diode
-25 °C…+50 °C
-40 °C…+60 °C
Approvals
Insulation coordination (EN 50 178) Standards
CE; cULus;
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.) mm2
Length x width x height
mm
300 V
4.0 kV
≥ 5.5 mm
III
2
Note
EN 50178
Screw connection
2.5 / 0.5 / 4
93 / 6.1 / 92
Tension clamp connection
1.5 / 0.5 / 2.5
94 / 6.1 / 91
CE, UL/UR
for mounting on TS 35
Ordering data
5 V DC / 24 V DC 2 A
24 V DC / 24 V DC 2 A
120 V UC / 24 V DC 2 A
230 V AC / 24 V DC 2 A
Input
Rated voltage
Rated current
Power rating
max. input frequency
Switch-on delay
Switch-off delay
5 V DC ±20%
11 mA DC ±10 %
55 mW ±10 %
300 Hz
< 55 µs
< 1 ms
24 V DC ±20 %
5.7mA
140 mW
300 Hz
< 55 µs
< 1.2 ms
120 V UC + 10 %/ -15 %
3,4 mA AC/2,8 mA DC
340 mW / 0.4 VA
DC: 10 Hz /AC: 3 Hz
< 6.5 ms
< 10 ms
230 V AC ±10%
7.4mA
1.7 VA
3 Hz
< 6.5 ms
< 10 ms
MOS 5Vdc / 24Vdc 2A
MOS 24Vdc / 24Vdc 2A
MOS 120Vuc / 24Vdc 2A
MOS 230Vac / 24Vdc 2A
8633000000
8607350000
8607700000
8607720000
MOZ 5Vdc / 24Vdc 2A
MOZ 24Vdc / 24Vdc 2A
MOZ 120Vuc / 24Vdc 2A
MOZ 230Vac / 24Vdc 2A
8632990000
8607370000
8607740000
8607760000
SSS Relais 5V/24V 2ADC
SSS Relais 24V/24V 2Adc
SSS Relais 60V/24V 2Adc
SSS Relais 24V/24V 2Adc
4064310000
4061190000
4061200000
4061190000
Ordering data
Complete module
Screw connection
Type
Order No.
Tension clamp connection
Type
Order No.
Ordering data
Spare relay, pluggable
Type
Order No.
Note
21
Solid-State Relays – MICROSERIES
MOS / MOZ actuator version 3...33 V DC / 2 A
Universal interface between control and sensor/actuator
• Plug-in cross-connection ZQV 4N
• Interchangeable solid-state relay
• 6.1 mm wide
• Screw or tension clamp connection
• For mounting on TS 35
13
cc
(24 V DC)
Output Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Short-circuit-proof/Protective circuit
General data Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178) Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Ordering data
24 V DC ACT
Input
Rated voltage
Rated current
Power rating
max. input frequency
Switch-on delay
Switch-off delay
24 V DC ±20 %
5.7 mA ±10 %
140 mW ±10 %
< 55 µs
< 1,2 ms
Ordering data
Complete module
Screw connection
Type
Order No.
Tension clamp connection
Type
Order No.
MOS 24Vdc / 24Vdc ACT
8676250000
MOZ 24Vdc / 24Vdc ACT
8676230000
Ordering data
Spare relay, pluggable
Type
Order No.
Note
22
SSS Relais 24V/24V 2Adc
4061190000
3…33 V DC
2A
≤ 120 mV
approx. 10 µA
no/Integrated free-wheel diode
-25 °C…+50 °C
-40 °C…+60 °C
CE; cULus;
EN 50178
300 V
4.0 kV
≥ 5.5 mm
III
2
Dimensions
Clamping range (rating- / min. / max.) mm2
Length x width x height
mm
Screw connection
2.5 / 0.5 / 4
93 / 6.1 / 92
Note
CE, UL/UR
for mounting on TS 35
Tension clamp connection
1.5 / 0.5 / 2.5
94 / 6.1 / 91
Optos – MICROSERIES
Plug-in solid-state relay
SSS Relay
SSS Relay
SSS Relay
Switching current 100 mA
Switching current 2 A
Switching current 1 A
Technical data
Input
Nominal control voltage
Control voltage
min / max
Control current at UIN = 24 V
Drop-out voltage
Control circuit resistance
24 V DC60 V DC
16 V DC / 30 V DC
52 V DC / 72 V DC
7 mA ± 10 %
2.8 mA ± 10 %
10 V DC
40 V DC
approx. 4 kΩ
approx. 20 kΩ
24 V DC60 V DC
18 V DC / 30 V DC
35 V DC / 72 V DC
7 mA ± 10 %
3.0 mA ± 10 %
10 V DC
20 V DC
approx. 3,2 kΩ
approx. 16 kΩ
24 V DC60 V DC
18 ... 30 V DC
35 ... 72 V DC
3.1 mA ± 10 %
3.1 mA ± 10 %
20 V DC
20 V DC
20 kΩ
20 kΩ
Bipolar transistor
3 ... 48 V DC
100 mA DC
MOS-FET
3 ... 33 V DC
2 A DC
TRIAC
24 ... 240 V AC
1 A AC
< 1 V DC
< 120 mV DC
< 1 V AC
2.5 kV
2.5 kV
2.5 kV
–20 °C … +60 °C
–40 °C … +70 °C
3.65 g
–20 °C … +60 °C
–40 °C … +70 °C
3.65 g
–20 °C … +60 °C
–40 °C … +70 °C
3.65 g
{
{
{
Output
Switching voltage
Switching/continuous current at UA > 5 V DC
Conducting-state voltage
Insulation
Test voltage between control/switching circuit
Other data
Operating temperature range
Storage temperature range
Weight
Approvals
* Ambient temperature 20 °C
Wiring diagram
A1 V
V (11)
A1 V
V (11)
A1 V
V (11)
A2 P
– (14)
A2 P
– (14)
A2 P
– (14)
Order No.
4064310000
4061190000
4061200000
Type
For further data, see also
http://em.tycoelectronics.com
Ordering data
Nominal control voltage
5 V DC
24 V DC
60 V DC
Type
Order No.
SSS Relais 5 V/24 V 0,1 A DC 4064320000
SSS Relais 24 V/24 V 0,1 A DC4061180000
SSS Relais 60 V/24 V 0,1 A DC4061230000
Type
SSS Relais 5 V / 24 V 2 A DC
SSS Relais 24 V/24 V 2 A DC
SSS Relais 60 V/24 V 2 A DC
Order No.
SSS Relais 24 V/230 V 1 A AC4061210000
SSS Relais 60 V/230 V 1 A AC4061220000
Dimensions
Printing details
23
Optos – MICROSERIES
Accessories
General data – MICROSERIES
Plug-in cross-connection
Technical data
No. of poles
Qty
2
3
4
10
20
60
60
60
20
20
1758250000
1762630000
1762620000
1758260000
1909020000
red
ZQV 4N / 2 RT
ZQV 4N / 3 RT
2
3
60
60
1793950000
1793980000
ZQV 4N / 4 RT
ZQV 4N / 10 RT
ZQV 4N / 20 RT
4
10
20
60
20
20
1794010000
1794040000
1909150000
blue
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
/
/
/
/
/
2 BL
3 BL
4 BL
10 BL
20 BL
2
3
4
10
20
60
60
60
20
20
1793960000
1793990000
1794020000
1794050000
1909100000
black
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
/
/
/
/
/
2 SW
3 SW
4 SW
10 SW
20 SW
2
3
4
10
20
60
60
60
20
20
1793970000
1794000000
1794030000
1794060000
1909120000
Type
Base only
MRZ 24VDC 1CO BASIS
MRS 24VDC 1CO BASIS
MRZ 120VUC 1CO BASIS
MRS 120VUC 1CO BASIS
MRZ 230VAC 1CO BASIS
MRS 230VAC 1CO BASIS
Qty
Other accessories
Nominal torque
Continuous current for 2-pole cross-connection
A
Continuous current for multi-pole cross-connection A
Stripping length
mm
Ingress protection class
Housing material
UL 94 flammability rating
Nominal current
A
Nominal voltage
V
0.6
10
10
7
IP 20
Wemid
V-0
6
250
200
1061160000
484 labels / sheet
10
1686360000
Screwdriver
SD 0,6 x 3,5 x 100
10
9008330000
Tension clamp connection
Screw connection
94 mm
92 mm
12 x 6 mm
24
-
10
10
10
IP 20
Wemid
V-0
6
250
General technical data
Dimensions
8826000000
8826010000
8826020000
8826030000
8826040000
8826050000
Labels, Lasermark
LM MT 300 15/6 ge
Screw
connection
0.5 … 4.0
0.5 … 2.5
0.5 … 1.5
0.5 … 1.5
0.13 … 4.0
A3
Order No.
10
10
10
10
10
10
Markers
WS 12/6
Tension clamp
connection
0.5 … 2.5
0.5 … 2.5
0.5 … 1.5
0.5 … 1.5
0.13 … 2.5
A 2
93 mm
6.1 mm
2 GE
3 GE
4 GE
10 GE
20
Conductor
Solid H07V-U
mm2
Stranded H07V-K
mm2
“f” with wire end ferrules to DIN 46228-1
mm2
“f” with wire end ferrules with plastic collar
mm2
Max. clamping range
mm2 Plug gauge to IEC 60947-1 size
91 mm
/
/
/
/
/
Order No.
6.1 mm
Type
yellow
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
Optos – MICROOPTO
For high switching frequencies up to
100 kHz
12...28 V DC 100 kHz
A special interior circuit in the opto ­module
MICROOPTO 100 kHz ensures that rapidly
transmitted signals are isolated from one another
and that they can be transferred ­practically without delay. This allows switching frequencies up to
100 kHz to be achieved.
• Design width just 6 mm
• Pluggable cross-connection
• Mount onto TS35
Comprehensive suppressor circuits safeguard the
module against conducted transients and voltage
spikes
+24 V DC
0V
Technical data (preliminary)
Control side
Rated control voltage
Rated power
Making voltage
Making voltage
Max. Input frequency
Status indicator
Protective circuit
Load side
Solid-state type
Rated switching voltage
Rated switching current
Voltage drop at max. load
Leakage current
Short-circuit proof/protective circuit
Switch-off delay/switch-on delay
Continuous current
Permissible short-circuit current/fuse
Load category
General data
Ambient temperature (operating)/storage temperature
Flammability rating to UL 94
Climate
Approvals
Standards
Insulation coordination (EN 50 178)
Rated voltage
Rated impulse voltage
Clearance and creepage distance control side - load side
Overvoltage category
Pollution severity
Eingang
12…28 V DC
0.08…0.3 W
> 70 % Urated
< 4.5 V
100 kHz
LED green
Diode for reverse polarity protection / varistor
Ausgang
Bipolar transistor
24 V DC
50 mA
≤ 1.5 V
< 20 µA
No / protective diode
< 3 µs / < 1 µs
50 mA
0.6 A (20 ms)it
LC A
Allgemeine Angaben
–20...+60 °C / –40...+80 °C
V0.
5...95 % (indoor), Tu = 40 °C, no condensation
CE, cULus (in preparation)
EN 50178, IEC 62314, UL508
Dimensions
Clamping range (rated / min. / max.)
Length x width x height
Screw connection
0,5...4,0 / 0,5...2,5
90 x 6.1 x 98
mm2
mm
For example rotational speed measurement
Sensor
Power supply
300 V
2,5 kV
> 3 mm
III
2
Hinweis
Order data
Connection type
Screw connection
Type
Qty
MOS 12-28 V DC 100kHz
1
Order No.
8937990000
Control
Note
Accessories
Note
25
Solid-state relay – MICROOPTO
For direct connection of actuators up
to 24 V DC 2 A
8...30 V DC 2 A
The solid-state relay MICROOPTO ACTOR has
been especially designed as a switching amplifier
for actuators up to 24 V DC and 2A with inductive
loads such as solenoid valves and contactors.
3-wire actuators can be connected directly to the
module.
• Design width just 6 mm
• Pluggable cross-connection
• PE connection integrated in mounting rail
• Status indication of fault in output
This is short-circuit proof and protected against
application-related transients and spikes by extensive protective circuitry.
+24 V DC
0V
A2
Technical data (preliminary)
Control side
Rated control voltage
Rated power
Making voltage
Making voltage
Max. Input frequency
Protective circuit
Load side
Solid-state type
Rated switching voltage
Rated switching current
Voltage drop at max. load
Leakage current
Short-circuit proof/protective circuit
Switch-off delay/switch-on delayl
Continuous current
Status indicator
Load category
General data
Ambient temperature (operating)/storage temperature
Flammability rating to UL 94
Climate
Approvals
Standards
Insulation coordination (EN 50 178)
Rated voltage
Rated impulse voltage
Clearance and creepage distance control side - load side
Overvoltage category
Pollution severity
Eingang
24 V DC ± 20 %
0.12 W
> 70 % Urated
< 12 V
100 Hz
Diode for reverse polarity protection / varistor
Ausgang
Intelligent POWER MOS-FET
8…30 V DC
2A
< 100 mV
< 100 µA
Yes (12 h) / varistor
< 0.5 ms / < 0.2 ms
2A
Error indication LED red; status LED green
LC A
Allgemeine Angaben
–20...+60 °C / –40...+80 °Ceingangsspannung, min.-max.
V0mpulslänge, min.
5...95 % (indoor), Tu = 40 °C, no condensation
CE, cULus (in preparation)
EN 50178, IEC 62314, UL508
Isolationskoordinaten
300 V
2.5 kV
> 3 mm ungsspannung
III tossspannung
2
Dimensions
Clamping range (rated / min. / max.)
Length x width x height
Screw connection
0,5...4,0 / 0,5...2,5
90 x 6.1 x 98
mm2
mm
Example: pneumatic valve
bar
PE
Valve
Power
supply
Note
PE
Order data
Connection type
Note
Accessories
Note
26
Screw connection
Type
Qty
MOS 24 V DC/8-30 V DC 2A
1
Order No.
8937970000
Control
Solid-state relay – MICROOPTO
For DC loads up to 300 V DC and 1 A
12...300 V DC 1 A
• Design width just 6 mm
The solid-state relay MICROOPTO 300 V DC has
been developed as a switching amplifier for high
inductive loads up to 300 V DC and 1 A in motor
brakes and contactors.
• Pluggable cross-connection
• Power Boost: 20 A / 20 ms, 5 A / 1 s
A power boost in the load circuit compensates
transient overloads (20 A for 20 ms / 5 A for 1
s) such as making or breaking spikes. Additional
protective circuits counter higher overloads.
Technical data (preliminary)
Control side
Rated control voltage
Rated power
Making voltage
Making voltage
Max. Input frequency
Status indicator
Protective circuit
Load side
Solid-state type
Rated switching voltage
Rated switching current
Voltage drop at max. load
Leakage current
Short-circuit proof/protective circuit
Switch-off delay/switch-on delay
Continuous current
Permissible short-circuit current/fuse
Load category
General data
Ambient temperature (operating)/storage temperature
Flammability rating to UL 94
Climate
Approvals
Standards
Insulation coordination (EN 50 178)
Rated voltage
Rated impulse voltage
Clearance and creepage distance control side - load side
Overvoltage category
Pollution severity
Eingang
24 V DC ± 20 %
0.26 W
19.6 V DC
< 12 V
100 Hz
LED green
Diode for reverse polarity protection / varistor
Ausgang
MOS-FET
12…300 V DC
1A
<1V
< 100 µA
Powerboost 20 A / 20 ms, 5 A / 1 s / varistor
< 0.3 ms / < 0.2 ms
1A
27 A (10 ms) wortzeit
LC A
Allgemeine Angaben
–20...+60 °C / –40...+80 °Cinput voltage, min./max.
V0pulse length, min.
5...95 % (indoor), Tu = 40 °C, no condensation
CE, cULus (in preparation)
EN 50178, IEC 62314, UL508
Isolationskoordinaten
300 V
2,5 kV
> 3 mm ungsspannung
III tossspannung
2
Dimensions
Clamping range (rated / min. / max.)
Length x width x height
Schraubanschluss
0,5...4,0 / 0,5...2,5
90 x 6.1 x 98
mm2
mm
Example: motor brake
Power supply
Note
Order data
Connection type
Screw connection
Type
Qty
MOS 24VDC/12-300VDC 1A
1
Order No.
8937830000
Control
Note
Accessories
Note
27
Optos – MCZ-SERIES
MiniConditioner MCZ O
24 V UC
24 V UC / 24 V 2 A
•U
niversal interface between control and sensor/actuator
• Direct switching of load currents up to 2 A DC
• Tension clamp connection system
• Plug-in cross-connection
• Width 6mm
3
VCC
+24 V
2
0V
5
+
OUTPUT
48 V = / 20 mA
2
3
4
4
GND
0V
OUTPUT
Input
Input
5
1
24 V
OUT
24V
2A
Technical data
Input
Rated voltage mn;20 %
Rated current mA DC
Power rating mVA
max. input frequency z
Auxiliary voltage
Status indicator
Output
Output voltage n;20%
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay / DC: 40 ms
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals ;CE;
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
24 V DC ±20 %
11 mA AC / 9 mA DC
230 mW / 280 mVA
AC: 5 Hz / DC: 10 Hz
no iliary voltage
LED green icator
Output
5…48 V DC smn;20%
20 mA current (max.)
≤ 1 V e drop at max. load
Block-state curr. (closed-circuit curr.)
AC: 10 ms / DC: 20 ms /AC: 45 ms / DC: 40 ms
no /Integrated free-wheel diode ircuit
General data
-25 °C…+50 °C ature
-40 °C…+85 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Input
24 V DC ±20 %
13 mA AC /12 mA DC
195 mW / 220 mVA
AC: 10 Hz / DC: 30 Hz
no iliary voltage
LED * indicator
Output
24 V DC ±20%
2 A ut current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
/ C: 10 ms / DC: 20 ms /AC: 45 ms / DC: 40 ms
yes /varistor proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+60 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Note
* Status LED: green = ok, yellow = low load, blinking red = short-circuit
Ordering data
Connection system
Tension clamp connection
Type
Qty.
MCZ O 24VUC
10
Order No.
8365940000
Type
Qty.
MCZ O 24VUC
10
Order No.
8287730000
Note
Accessories
Note
28
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
Optos – MCZ-SERIES
MiniConditioner MCZ O
120 V UC
230 V AC
•U
niversal interface between control and sensor/actuator
• Tension clamp connection system
• Plug-in cross-connection
• Width 6mm
3
4
2
Output
48 V = / 50 mA
3
4
0V
+
2
0 V
+
Output
Input
48 V = / 20 mA
Input
1
1
120 V
230 V
Technical data
Input
Rated voltage / -15 %
Rated current
Power rating mVA
max. input frequency 1:2, DC: 20 Hz duty factor 1:2
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals ;CE;
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
120 V UC +5/-15 % %
3 mA current
350 mW / 400 mVA
AC: 5 Hz duty factor 1:2, DC: 20 Hz duty factor 1:2
no iliary voltage
LED green icator
Output
5…48 V DC ge
50 mA current (max.)
≤ 1,6 V drop at max. load
0.16 mA ate curr. (closed-circuit curr.)
≤ 30 ms /≤ 40 ms off delay
no /Integrated free-wheel diode ircuit
General data
-25 °C…+40 °C ature
-40 °C…+60 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Input
230 V AC +5 %/ -15 %
10 mA current
2.3 VA / 400 mVA
AC: 5 Hz duty factor 1:2 DC: 20 Hz duty factor 1:2
no iliary voltage
LED green icator
Output
5…48 V DC ge
20 mA current (max.)
≤ 1,6 V drop at max. load
0.16 mA ate curr. (closed-circuit curr.)
≤ 30 ms /≤ 40 ms off delay
no /Integrated free-wheel diode ircuit
General data
-25 °C…+40 °C ature
-40 °C…+85 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Note
Ordering data
Connection system
Tension clamp connection
Type
Qty.
MCZ O 120VUC
10
Order No.
8421060000
Type
Qty.
MCZ O 230VAC
10
Order No.
8421380000
Note
Accessories
Note
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
29
Optos – MCZ-SERIES
MiniConditioner MCZ O
24 V DC / 5 V TTL
5 V TTL / 5…48 V DC
Module can be used as an universal interface:
•B
etween control and actuator, to convert
signals from 24 Vdc to 5 VTTL
•B
etween control and actuator, to convert
signals from 5 VTTL to 5…48 Vdc
4
3
VCC
+5 V
GND
OUTPUT
5
2
4
+
0V
OUTPUT
5...48 V = / 100 mA
INPUT
TTL
3
VCC
+5 V
1
+24 V
2
0V
INPUT
5
1
TTL
Technical data
Input
Rated voltage mn;16 %
Rated current
Power rating
max. input frequency 1:2, 50 kHz duty factor 1:10
Auxiliary voltage
Status indicator
Output
Output voltage .5.25 V)
Output current (max.) -TTL
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay V DC)
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals ;CE;
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
24 V DC ±16 %
4.7 mA urrent
112 mW ating
100 kHz duty factor 1:2, 50 kHz duty factor 1:10
no iliary voltage
LED green icator
Output
5 V TTL(4.75…5.25 V)
8 mA, fan out = 20 LS-TTL
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
1 µs (at 20 V DC) /2.5 µs (at 28 V DC)
no /diode uit-proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+60 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Input
5 V TTL ±16 %
1 µA current
10 mW rating
2.4 kHz duty factor 1:2, 50 kHz duty factor 1:10
5 V liary voltage
LED green icator
Output
5…48 V DC …5.25 V)
100 mA an out = 20 LS-TTL
≤ 1,8 V drop at max. load
Block-state curr. (closed-circuit curr.)
/ µs (at 20 V DC) /2.5 µs (at 28 V DC)
no /diode uit-proof/Protective circuit
General data
-25 °C…+50 °C ature
-40 °C…+85 °C ure
CSA;cURus;CE;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Note
Ordering data
Connection system
Tension clamp connection
Type
Qty.
MCZ O 24VDC
10
Order No.
8324610000
Type
Qty.
MCZ O 5VTTL
10
Order No.
8398940000
Note
Accessories
Note
30
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
Optos – MCZ-TRAK-SERIES
MCZ O TRAK
24 V DC TRAK
• Module for rail industry applications
• Meets requirements of EN 50155
• Power fluctuations -30 %/+25 %
•O
perating temperature -25…+70 °C (85 °C /
10 min.) as per EN 50155
• Condensation permissible
4
+
3
Output
5
2
0V
Input
5 V ... 110 V DC
250 mA
1
24 ... 110 V DC
Technical data
Input
Rated voltage -30/+25%
Rated current DC 2.8 mA @ 110 V DC
Power rating
max. input frequency
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.) A @ 70 °C
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature ;-25 °C…+70 °C
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Input
24…110 V DC -30/+25%
1.9 mA @ 24 V DC 2.8 mA @ 110 V DC
Power rating
10 Hz nput frequency
no iliary voltage
LED green icator
Output
5…137,5 V DC
250 mA @ 50 °C ;180 mA @ 70 °C
≤ 1.7 V p at max. load
Block-state curr. (closed-circuit curr.)
10 ms /50 ms ay/Switch-off delay
/Varistor, integral free-wheel diode t
General data
+85°C for 10 minutes ;-25 °C…+70 °C
-40 °C…+85 °C ure
CE; ovals
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
6.0 kV impulse withstand voltage
≥ 5.5 mm clearance path input - output
III voltage category
2 llution severity
mm2
mm
Tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 64
Note
Ordering data
Connection system
Tension clamp connection
Type
Qty.
MCZ O TRAK 24.110VDC
10
Order No.
8820710000
Note
Accessories
Note
End plate AP MCZ 1.5: 8389030000
for cross-connectors and markers see MCZ Series accessories
31
Optos – MCZ-SERIES-Accessories
MCZ accessories
63.2
56
91
TS-Contact
Ordering data
End plate
Type
AP MCZ 1.5
Qty
50
Order No.
8389030000
Type
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
ZQV 4N
/
/
/
/
/
2 GE
3 GE
4 GE
10 GE
20 GE
Qty
60
60
60
20
20
Order No.
1758250000
1762630000
1762620000
1758260000
1909020000
ZQV
ZQV
ZQV
ZQV
ZQV
4N
4N
4N
4N
4N
/
/
/
/
/
2 RT
3 RT
4 RT
10 RT
20 RT
60
60
60
20
20
1793950000
1793980000
1794010000
1794040000
1909150000
4N
4N
4N
4N
4N
/
/
/
/
/
2 BL
3 BL
4 BL
10 BL
20 BL
60
60
60
20
20
1793960000
1793990000
1794020000
1794050000
1909100000
4N
4N
4N
4N
4N
/
/
/
/
/
2 SW
3 SW
4 SW
10 SW
20 SW
60
60
60
20
20
1793970000
1794000000
1794030000
1794060000
1909120000
Qty
200
Order No.
1060960000
Ordering data
Plug-in
Plug-in
Plug-in
Plug-in
Plug-in
cross-connection,
cross-connection,
cross-connection,
cross-connection,
cross-connection,
yellow yellow
yellow
yellow
yellow
Plug-in
Plug-in
Plug-in
Plug-in
Plug-in
cross-connection,
cross-connection,
cross-connection,
cross-connection,
cross-connection,
red
red
red
red
red
No. of poles
2
3
4
10
20
2
3
4
10
20
Plug-in
Plug-in
Plug-in
Plug-in
cross-connection,
cross-connection,
cross-connection,
cross-connection,
blue
blue
blue
blue
3
4
10
20
ZQV
ZQV
ZQV
ZQV
ZQV
Plug-in
Plug-in
Plug-in
Plug-in
Plug-in
cross-connection,
cross-connection,
cross-connection,
cross-connection,
cross-connection,
black
black
black
black
black
2
3
4
10
20
ZQV
ZQV
ZQV
ZQV
ZQV
Plug-in cross-connection, blue
2
Ordering data
Marker
32
Type
WS10/6
33
Solid-State Relays – PLUGSERIES
POS / POZ
24 V DC / 24 V DC 2.5 A
24 V DC / 24 V DC 5 A
Universal interface between control and sensor
• Plug-in cross-connection ZQV 2.5N
• Interchangeable solid-state relay
• Screw or tension spring connection
• For mounting on TS 35
A1
A2
21
14
Load
A1
A2
Load
*
Free wheel diode for
inductive loads*
21
14
*
Free wheel diode
for inductive loads*
Technical data
Input
Rated voltage V DC
Rated current
Power rating
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
15 V DC…30 V DC
approx. 10 mA
250 mW ating
no iliary voltage
green LED icator
Output
0…30 V DC ge
2.5 A current (max.)
≤ 0,4 V drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
2ms /18ms delay/Switch-off delay
no /Integrated free-wheel diode ircuit
General data
-40 °C…+50 °C ature
-40 °C…+ 50 °C re
CE;cURus;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
2.5 kVeff and voltage
8 mm age and clearance path input - output
III voltage category
2 llution severity
Input
15 V DC…30 V DC
approx. 10 mA
250 mW ating
no iliary voltage
green LED icator
Output
0…30 V DC ge
5 A ut current (max.)
≤ 0,3 V p at max. load
≤ 1 mA e curr. (closed-circuit curr.)
2ms /18ms delay/Switch-off delay
no /Integrated free-wheel diode ircuit
General data
-40 °C…+50 °C ature
-40 °C…+ 50 °C re
CE;cURus;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
2.5 kVeff and voltage
8 mm age and clearance path input - output
III voltage category
2 llution severity
Screw connection
2.5 / 0.5 / 2.5
92 x 15.3 x 95
Screw connection
2.5 / 0.5 / 2.5
92 x 15.3 x 95
Tension clamp connection
2.5 / 0.5 / 2.5
92 x 15.3 x 87
Tension clamp connection
2.5 / 0.5 / 2.5
92 x 15.3 x 87
Note
Ordering data
Connection system
Note
Screw connection
Tension clamp connection
Type
Qty.
POS 24VDC/24VDC 2A
10
POZ 24VDC/24VDC 2A
10
Spare SSR
8576340000
Order No.
8610840000
8610920000
Type
Qty.
POS 24VDC/24VDC 5A
10
POZ 24VDC/24VDC 5A
10
Spare SSR
8576350000
Accessories
Note
34
Cross-connectors and markers - see
PLUGSERIES accessories
Cross-connectors and markers - see
PLUGSERIES accessories
Order No.
8610900000
8610970000
Solid-State Relays – PLUGSERIES
POS / POZ
24 V DC / 230 V AC 2 A
24 V DC / 230 V AC 4 A
Universal interface between control and sensor
• Plug-in cross-connection ZQV 2.5N
• Interchangeable solid-state relay
• Screw or tension spring connection
• For mounting on TS 35
12-275 VAC
N
12-275 VAC
N
L1
A1
21
A2
14
L1
Load
A1
21
A2
14
Load
Technical data
Input
Rated voltage V DC
Rated current
Power rating
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
15 V DC…30 V DC
approx. 10 mA
250 mW ating
no iliary voltage
green LED icator
Output
12…275 V AC
2 A ut current (max.)
≤ 1 V e drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
12ms /20ms elay/Switch-off delay
no /RC element roof/Protective circuit
General data
-40 °C…+50 °C ature
-40 °C…+ 50 °C re
CE;cURus;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kVeff and voltage
8 mm age and clearance path input - output
III voltage category
2 llution severity
Input
15 V DC…30 V DC
approx. 10 mA
250 mW ating
no iliary voltage
green LED icator
Output
12…275 V AC
3 A (4 A at 20°C) x.)
≤ 1,1 V drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
12ms /20ms elay/Switch-off delay
no /RC element roof/Protective circuit
General data
-40 °C…+50 °C ature
-40 °C…+ 50 °C re
CE;cURus;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kVeff and voltage
8 mm age and clearance path input - output
III voltage category
2 llution severity
Screw connection
2.5 / 0.5 / 2.5
92 x 15.3 x 95
Screw connection
2.5 / 0.5 / 2.5
92 x 15.3 x 95
Tension clamp connection
2.5 / 0.5 / 2.5
92 x 15.3 x 87
Tension clamp connection
2.5 / 0.5 / 2.5
92 x 15.3 x 87
Note
Ordering data
Connection system
Note
Screw connection
Tension clamp connection
Type
Qty.
POS 24VDC/230VAC 2A
10
POZ 24VDC/230VAC 2A
10
Spare SSR
8576370000
Order No.
8610860000
8610930000
Type
Qty.
POS 24VDC/230VAC 4A
10
POZ 24VDC/230VAC 4A
10
Spare SSR
Order No.
8610910000
8610980000
8576360000
Accessories
Note
Cross-connectors and markers - see
PLUGSERIES accessories
Cross-connectors and markers - see
PLUGSERIES accessories
35
Solid-State Relays – PLUGSERIES
POS / POZ
24 V DC / 24 V UC 1 A
Universal interface between control and sensor
• Plug-in cross-connection ZQV 2.5N
• Interchangeable solid-state relay
• Screw or tension spring connection
• For mounting on TS 35
max. 30 V AC/DC
L1
N
21
A1
STN
Last
14
A2
Derating curves
Technical data
Input
15 V DC…30 V DC
approx. 10 mA
250 mW ating
no iliary voltage
green LED icator
Output
0…30 V UC ge
1 A ut current (max.)
≤ 0,9 V drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
5ms /12ms delay/Switch-off delay
no /Integrated free-wheel diode ircuit
General data
-40 °C…+50 °C ature
-40 °C…+ 50 °C re
CE;cURus;
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kVeff and voltage
8 mm age and clearance path input - output
III voltage category
2 llution severity
24 V DC / 24 V DC 2.5 A
4
3,5
3
TJ = 125 °C
II (A)
2,5
Tc = 90 °C
2
1,5
1
0,5
0
0
10 20 30 40 50
60 70
80 90 100 110
Temperature (°C)
24 V DC / 24 V DC 5 A
8
7
TJ = 125 °C
6
Tc = 90 °C
5
II (A)
Input
Rated voltage V DC
Rated current
Power rating
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
4
3
2
1
0
0
10 20 30 40 50
60 70
80 90 100 110
Temperature (°C)
24 V DC / 24 V UC 1 A
1,6
1,4
1,2
II (A)
1,0
TJ = 125 °C
0,8
Tc = 90 °C
0,6
0,4
0,2
0
0
10 20 30 40 50
60 70
80 90 100 110
Temperature (°C)
24 V DC / 230 V AC 2 A
4
3,5
mm2
mm
Screw connection
2.5 / 0.5 / 2.5
92 x 15.3 x 95
Tension clamp connection
2.5 / 0.5 / 2.5
92 x 15.3 x 87
3
2,5
II (A)
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
TJ = 125 °C
2
Tc = 90 °C
1,5
Note
1
0,5
0
0
10 20 30 40 50
Ordering data
Note
Screw connection
Tension clamp connection
Type
Qty.
POS 24VDC/24VUC 1A
10
POZ 24VDC/24VUC 1A
10
80 90 100 110
Spare SSR
8576380000
24 V DC / 230 V AC 4 A
Order No.
8610890000
8610960000
5
4,5
4
3,5
II (A)
Connection system
60 70
Temperature (°C)
TJ = 125 °C
3
Tc = 90 °C
2,5
2
1,5
1
0,5
Accessories
Note
36
0
Cross-connectors and markers - see
PLUGSERIES accessories
0
10 20 30 40 50
60 70
Temperature (°C)
80 90 100 110
Solid-State Relays – PLUGSERIES
PLUGSERIES
Accessories
Marking area
Retaining clip
87 (PXZ35)
95 (PXS35)
Cross-connection
opening A1 / A2
Cross-connection
opening 11 / 21
92
Technical data
screw connection
tension clamp connection
Ambient temperature
UL 94 flammability rating
16 A
250 V
> 4 kV
IP 20
2.5 mm2
8 mm
10 mm
–40 °C ... +60 °C
V-0
Tension clamp
connection
Screw
connection
15.3
15.3
15,3
Base without relay
Nominal current
Nominal voltage
Dielectric strength coil/contact
Ingress protection class
Nominal cross-section
Stripping length
22
12
(NC)
22
12
(NC)
21
11
(COM)
21
11
(COM)
24
14
(NO)
24
14
(NO)
A2
A1
(COIL)
A2
A1
(COIL)
Ordering data
Base for mounting on TS 35 rail
Screw connection
Tension clamp connection
Type
Qty
PXS35
10
PXZ35
10
Order No.
8533771001
8536691001
Retaining clip
PRC
LED indicator with free-wheel diode
6 ... 24 V DC
red LED, 6 ... 24 V DC
48 ... 60 V DC
115 V DC
12 ... 24 V AC
115 V AC
230 V AC
RC combination, 120 ... 230 V AC/DC
Plug-in cross-connections
2-pole Markers
black
red
blue
100
8536700000
20
20
20
20
20
20
20
20
8536710000
8611010000
8536720000
8536730000
8536750000
8536760000
8536780000
8566530000
Betriebsanzeige
PLED 24 V DC
PLED 24 V DC red
PLED 48 V DC
PLED 115 V DC
PLED 24 V AC
PLED 120 V AC
PLED 230 V AC
PLRC 200 nF/200 Ω
ZQV 2.5N/4-2SW
ZQV 2.5N/4-2RT
ZQV 2.5N/4-2BL
60
60
60
1784270000
1784280000
1784290000
DC-Version
DC-Version
A1
12 14
14
A1
12
WS 10/5
WS 15/5
200
96
1060860000
1609880000
22
*
A2
A2
21
11
* Freilaufdiode
AC-Version
14
A1
12
24
22
AC-Version
12 14
A1
10 x 5 mm
15 x 5 mm
24
A2
11
21
A2
37
Solid-State Relays – RSO-SERIES
RSO 30
RSO 30-DV/SC
RSO 30-DV/SA
• Plug-in connections
• DC output up to 3 A @ 5…60 V DC
• AC output up to 3 A @ 24…240 V AC
• 11 mm wide
+
+
–
2
4
1
3
~
+
–
2
4
1
3
–
~
Technical data
Input
Rated voltage 0%
Rated current
Power rating
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
5…24 V DC ± 20%
5…35 mA ent
Power rating
no iliary voltage
LED green icator
Output
2…60 V DC ge
3 A ut current (max.)
Voltage drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
0.1 ms /0.75 ms Switch-off delay
no / t-circuit-proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+85 °C ure
CE; ovals
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kV impulse withstand voltage
≥ 8 mm nd clearance path input - output
III voltage category
2 llution severity
Input
5…24 V DC ± 20%
5…35 mA ent
Power rating
no iliary voltage
LED green icator
Output
24…250 V AC
3 A ut current (max.)
1.6 V e drop at max. load
≤ 5 mA e curr. (closed-circuit curr.)
Zero-voltage switch / h-off delay
no / t-circuit-proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+85 °C ure
CE; ovals
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kV impulse withstand voltage
≥ 8 mm nd clearance path input - output
III voltage category
2 llution severity
2.5 / 0.5 / 2.5
80 x 11 x 50
2.5 / 0.5 / 2.5
80 x 11 x 50
Note
Ordering data
Connection system
Note
Accessories
Note
38
Type
Qty.
RSO 30/DV 5-24V CC/SC
20
Order No.
9443100000
Type
Qty.
RSO 30/DV 5-24V CC/SA
20
Order No.
9443110000
Solid-State Relays – RSO-SERIES
RSO 31
RSO 31 -ODC/F
RSO 31 -OAC/F
• Plug-in connections
• DC output up to 3 A @ 5…60 V DC
• AC output up to 3 A @ 24…240 V AC
• 12.5 mm wide
• Plug-in fuse in output circuit
0V
Technical data
Input
Rated voltage
Rated current
Power rating
Auxiliary voltage
Status indicator
Output
Output voltage
Output current (max.)
Voltage drop at max. load
Block-state curr. (closed-circuit curr.)
Switch-on delay/Switch-off delay
Short-circuit-proof/Protective circuit
General data
Operating temperature
Storage temperature
Approvals
Insulation coordination (EN 50 178)
Standards
Rated voltage
Rated impulse withstand voltage
Creepage and clearance path input - output
Surge category
Pollution severity
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
mm2
mm
Input
24 V DC ±10%
Rated current
0.29 W ating
no iliary voltage
LED red ndicator
Output
5…50 V DC ge
3 A ut current (max.)
1.6 V e drop at max. load
≤ 1 mA e curr. (closed-circuit curr.)
0.1 ms /0.75 ms Switch-off delay
no / t-circuit-proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+85 °C ure
CE; ovals
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kV impulse withstand voltage
≥ 8 mm nd clearance path input - output
III voltage category
2 llution severity
Input
24 V DC ±10%
Rated current
0.29 W ating
no iliary voltage
LED red ndicator
Output
24…250 V AC
3 A ut current (max.)
1.6 V e drop at max. load
≤ 5 mA e curr. (closed-circuit curr.)
Zero-voltage switch / h-off delay
no / t-circuit-proof/Protective circuit
General data
-25 °C…+40 °C ature
-40 °C…+85 °C ure
CE; ovals
Insulation coordination (EN 50 178)
EN 50178
300 V voltage
4.0 kV impulse withstand voltage
≥ 8 mm nd clearance path input - output
III voltage category
2 llution severity
2.5 / 0.5 / 2.5
80 x 12.5 x 65.5
2.5 / 0.5 / 2.5
80 x 12.5 x 65.5
Note
Ordering data
Connection system
Type
Qty.
RSO31-ODC24/F
20
Order No.
9430820000
Type
Qty.
RSO31-OAC24/F
20
Order No.
9430320000
Note
Accessories
Note
39
Worldwide activities
AE
UAE
United Arab Emirates
Weidmuller Middle East FZE
P.O. Box # 8591
SAIF-Zone
Sharjah – UAE
Phone +971 6 5572723
Fax +971 6 5572724
[email protected]
AR
Argentina
CPI SA
Bauness 2660
1431 Buenos Aires
Phone +54 11 45238008
Fax +54 11 45220546
[email protected]
AT
AU
AZ
BA
BE
BG
Austria
Weidmüller Ges.m.b.H.
Industriezentrum Nö Süd
Straße 2, Objekt M2
2355 Wiener Neudorf
Phone +43 2236 6708-0
Fax +43 2236 6708-199
[email protected]
Australia
Weidmüller Pty. Ltd.
43 Huntingwood Drive
Huntingwood,
NSW, 2148
P.O.Box 6944
Blacktown
NSW, 2148
Phone +61 2 9671-9999
Fax +61 2 9671-9911
[email protected]
www.weidmuller.com.au
Azerbaijan
West Industries Ltd.
Caspian Plaza, 5-th Floor
44 J. Jabbarly Str., Baku, Azerbaijan
Phone +99412 499 15 15
Fax +99412 499 14 93
[email protected]
Bosnia-Herzegovina
BH ES Elektrosistem d.o.o.
ul. J. Veselinovica 18
78000 Banja Luka
Bosna
Phone +387 51 317500
Fax +387 51 317500
[email protected]
www.elektrosistem.co.yu
Belgium
Weidmüller Benelux B.V.
Mechelsesteenweg 519 bus 6 en 7
1930 Nossegem
Phone +32 (0)2 752 40 70
Fax +32 (0)2 751 36 06
[email protected]
Bulgaria
Weid-Bul eOOd
ul. Nezabravka 33 A,
bl. 315/3/10
1113 Sofia
Phone +359 2 9632560
Fax +359 2 9631098
[email protected]
BH
Bahrain
Khayber Trading Company
P.O. Box 1976 Manama,
Bahrain
Phone +973 17720747
Fax +973 17720331
[email protected]
BR
Brazil
Conexel Conexoes Elétricas Ltda.
Rua Garcia Lorca, 176- V. Paulicéia,
09695-900, Sao Bernado do
Campo - SP, Brasil
Phone +55 11 43669600
Fax +55 11 43621677
[email protected]
www.conexel.com.br
BY
40
Belarus
TECHNIKON Ltd.
Oktyabrskaya Str. 16/5
Apt. 704
220030 Minsk
Belarus
Phone +375 17 2104626
Fax +375 17 2275830
[email protected]
CA Canada
W Interconnections Canada Inc.
10 Spy Court, Markham,
Ontario L3 R5 H6
Phone +1 905 475-1507
Fax +1 905 475-5855
[email protected]
www.weidmuller.ca
CG Republic of Montenegro
Please contact
ES-YU Elektrossistem,
Republic of Serbia
CH Switzerland
Weidmüller Schweiz AG
Rundbuckstrasse 2
8212 Neuhausen am Rheinfall
Phone +41 52 6740707
Fax +41 52 6740708
[email protected]
www.weidmueller.ch
CL
Chile
Felipe Bahamondes S.A./ATS AGRO
Servicios Agroindustriales
Maria Luisa Santander 0475
Providencia
Casilla 3425
Santiago
Phone +56 2 341-1271
Fax +56 2 341-1275
[email protected]
CN China
Weidmüller Interface International
Trading (Shanghai) Co., Ltd.
12 F, Century Ba-Shi Building,
No. 398 Huaihai Road (M)
Shanghai 200020
P.R. China
Phone +86 21 63868188
Fax +86 21 63867177
www.cnweidmuller.com
CO Colombia
Automatizacion Avanzada S. A.
Carrera 97 No. 42 A-23 B3,
Santafe de Bogotá Colombia.
Phone +57 1 4132048
Fax +57 1 4159788
mgallegos@
automatizacionavanzada.com
CR Costa Rica
ELVATRON S.A.
400 Norte
Banco Costa Rica, la Uruca,
San José, Costa Rica
Phone +506 2 961060
Fax +506 2 960328
[email protected]
CS Republic of Serbia
ES-YU Elektrosistem
Pariske komune 41
11070 Novi Beograd
Serbia
Phone +381 11 697212
Fax +381 11 693608
[email protected]
www.elektrosistem.co.yu
CZ Czech Republic
Weidmüller s. r. o.
Videnska ul. 340
25242 Vestec u Prahy
Phone +420 2 44001400
Fax +420 2 44001499
[email protected]
DE Germany
Weidmüller GmbH & Co. KG
Ohmstraße 9
32758 Detmold
Phone +49 5231 1428-0
Fax +49 5231 1428-116
[email protected]
www.weidmueller.de
DK Denmark
Knud Wexøe A/S
Skaettekaeret 11
P.O. Box 152
2840 Holte
Phone +45 45465800
Fax +45 45465801
[email protected]
EC Ecuador
Elsystec S.A.
Electricidad Sistemas y Tecnología
Joaquin Tinajero E 3-25 y Jorge Drom
Edificio Oquendo, Planta baja, Oficina 101
Quito, Ecuador
Phone +593 2 2245 241
Fax +593 2 2456 755
[email protected]
EE Estonia
Alter Electric OÜ
Türi 6, 11313 Tallinn, Estonia
Phone +372 65 19 666
Fax +372 65 19667
[email protected]
EG Egypt
Standard Electric
87, Mohamed Farid Street
Heliopolis, Cairo, Egypt
Phone +20 6 42 29 77/ 6 42 29 88
Fax +20 6 42 29 55
[email protected]
ES Spain
Weidmüller S. A.
Narcis Monturiol 11-13
Pol.Ind. Sudoeste
08960 Sant Just Desvern
Barcelona
Phone +34 93 4803386
Fax +34 93 3718055
[email protected]
www.weidmuller.es
FI
Finland
JUHA-ELEKTRO OY
Kylvöpolku 6, P. O. Box 57
00681 Helsinki
Phone +358 10 8328 100
Fax +358 10 8328 169
FR France
Weidmüller EURL
12, Chaussée Jules César
B.P. 263 Osny
95523 Cergy Pontoise Cedex
Phone +33 1 34245500
Fax +33 1 34245501
[email protected]
www.weidmueller.com
HU Hungary
Weidmüller Kereskedelmi Kft
Mádi u. 50
1104 Budapest
P. O. Box 22
1507 Budapest
Phone +36 1 464-7888
Fax +36 1 3827701
[email protected]
IE
Ireland
A.P. Haslam Ltd.
14 Sunshine Ind. Estate
Crumlin Road
Dublin 12
Phone +353 1 453-2522
Fax +353 1 453-2949
[email protected]
IL
Israel
A.U. Shay Ltd.
Embar Street 23/25
P.O.Box 10049
Petach-Tikva 49222
Phone +972 3 9233601
Fax +972 3 9234601
[email protected]
IL
Israel
ATEKA Ltd.
23 Hayetzira St.
Kiryat Aryeh
49130 Petach-Tikva, Israel
Phone +972 3 9392344
Fax +972 3 9243273
[email protected]
www.ateka.co.il
IN
India
Weidmüller
Representative office
Vijay Dattani
# 156-4th cross, Prashant Extension
Whitefield
Bangalore - 560 066
Phone +91 80 8453999
[email protected]
IR
Iran
TAF Co.
72, Iranshahr Av.
Unit 5,
15816 Teheran
Phone +98 21 8831-7851
Fax +98 21 8882-0268
[email protected]
IS
Iceland
Samey Automation Center
Lyngas 13, 210 Garoabaer,
Iceland
Phone +354 510 5200
Fax +354 510 5201
[email protected]
IT
Italy
Weidmüller S.r.l.
Via Albert Einstein 4
20092 Cinisello Balsamo
Milano
Phone +39 02 660681
Fax +39 02 6124945
[email protected]
www.weidmuller.it
GR Greece
Electrorama S.A.
1 An. Martali Str.
41335 Larissa
Phone +30 2410 552533
Fax +30 2410 283463
[email protected]
HR Croatia
Elektro Partner d.o.o.
Radnicka cesta 22
10000 Zagreb
Phone +385 1 6184793
Fax +385 1 6184795
[email protected]
Indonesia
P. T. Nego Electrindo
Komplek Sentra Kramat, Blok A18
Jl. Kramat Raya No. 7-9
Jakarta 10450 Indonesia
Phone +62 21 3156218
Fax +62 21 3156219
[email protected]
GB United Kingdom
Weidmuller Ltd.
1 Abbey Wood Road
Kings Hill, West Malling
Kent ME19 4YT
Phone +44 1732 877000
Fax +44 1732 873873
[email protected]
www.weidmueller.com
HK Hong Kong
United Equity Limited
Suite B, 11/F International Industrial
Centre
2-8 Kwei Tei Street, Fotan, Shatin
Hong Kong
Phone +852 26876739
Fax +852 26876735
[email protected]
ID
JO Jordan
Trans Jordan for Electro
Mechanic Supplies PLC.
P.O.Box: 330607
Amman 11133, Jordan
Phone +962 6 533 2020
Fax +962 6 533 5800
[email protected]
JP
Japan
Nihon Weidmüller Co. Ltd.
Asahi Seimei Bldg. 11F
1-14-1 Fuchucho Fuchu-shi
Tokyo 183-0055 Japan
Phone +81 42 330-7891
Fax +81 42 330-7895
www.weidmuller.co.jp
KR South Korea
Weidmüller Co., Ltd.
6floor, Seahwa building, 242-54
Nonhyun-dong, Kangnam-Gu
Seoul
Korea, Zip: 135-830
Phone +82 2 5160003
Fax +82 2 5160090
[email protected]
KW Kuwait
KANA CONTROLS General
Trading & Cont. CO. W.L.L.
Al Rai Industrial Area,
Plot 28-30, St. 31, Kuwait
P.O.Box: 25593
Safat, 13116 Kuwait
Phone +965-474 1373/4
Fax +965-474 1537
[email protected]
KZ Kazakhstan
SEA STAR INTERNATIONAL. L.L.P.
42-A, Suite-15, Dostyk Ave
Almaty - 050010
Republic of Kazakhstan
Phone +7 3272 2 662502 / 938842 /
910580 / 911193
Fax +7 3272 2 501780
[email protected]
www.seastar.kz
LB
LT
LU
LV
Lebanon
Progress Engineering & Trading
Enterprises
P.O. Box 11-1111
Pharaon Bldg., Opp Electr. du Liban
Chafaca Str., Al Nahr
Beirut - Lebanon
Phone +961 1 444664
Fax +961 1 561880
[email protected]
MY Malaysia
Connect Plus Technology Sdn Bhd
9, Jalan PJS 11/24,
Bandar Sunway,
46150 Petaling Jaya,
Selangor Darul Ehsan,
Malaysia
Phone +60 3 5633 7363
Fax +60 3 5633 6562
[email protected]
www.cptech.com.my
NL
Latvia
PROFS Latvija SIA
K. Ulmana gatve 140
LV-1029 Riga
Latvia
Phone +371 7870557
Fax +371 7870541
[email protected]
www.profs.lv
NZ
PE
PH
MK Macedonia
ELEKTRO – SMK dooel
UL. III Makedonska brigada b.b.
1000 Skopje
Macedonia
Phone +389 22 460 295
Fax +389 22 460 298
[email protected]
PH
MT Malta
E.S.S.
Electrical Supplies & Services Ltd
104 J. Sciberras Str.
Hamrun
Malta HMR 08
Phone +356 21 255 777
Fax +356 21 255 999
[email protected]
New Zealand
Cuthbert S. Steward Limited
27 Te Puni Street
POB 38496 Petone
Petone, Wellington
Phone +64 4 5686156
Fax +64 4 5686056
OM Oman
DAN INTERNATIONAL LLC.
PO.BOX 2901
111 Seeb
Oman
Phone +968 503 677
Fax +968 503 755
[email protected]
MD Moldova
BERHORD A&D srl
44, srt. Sarmizegetusa 37/3
Off 414. b-dul Decebal, 3, MD2001
Chisinau, Republic of Moldova
Phone +373 22 507137
Fax +373 22 507134
[email protected]
Qatar
Doha Motors
(Technical Division)
Post Box No. 145
Al Wakrath Road
Doha-Qatar
Phone +974 465 1441
Fax +974 465 4579
[email protected]
RO Romania
Rominterface Impex SRL
Str. Gh. Dem Teodorescu 30A
030916 Bukarest - sector 3
Phone +40 21 3220230
Fax +40 21 3228857
[email protected]
NO Norway
Siv. Ing. J. F. Knudtzen A/S
Billingstadsletta 97
1396 Billingstad, P.O. Box 160
1378 Nesbru
Phone +47 66 983350
Fax +47 66 980955
[email protected]
Lithuania
ELEKTROS IRANGA
Tinklu g.29a, 5319 Panevezys,
Lithuania
Phone +370 45582828
Fax +370 45582727
[email protected]
Luxembourg
Weidmüller Benelux B.V.
Phone +352 24 527145
Fax +352 24 527147
[email protected]
Netherlands
Weidmüller Benelux B.V.
Franciscusweg 221
1216 SE Hilversum
Postbus 1505
1200 BM Hilversum
Phone +31 35 6261261
Fax +31 35 6234569
[email protected]
www.weidmuller.nl
QA
PL
MX Mexico
W Interconnections, S.A. de C.V.
Blvd. Hermanos Serdán No. 698
Col. San Rafael Oriente
Puebla, Pue. C.P. 72029
Phone +52 222 2686266 to 68 ext.101
Fax +52 222 2686219
[email protected]
www.weidmuller.com.mx
PT
PY
Peru
TECNOLOGÍA ELÉCTRICA
Y SOLUCIONES S.A.C.
Calle Huandoy 501, Lima 32 – Perú
Phone +51 1 5620004
Fax +51 1 5620004
[email protected]
Philippines
El Criscent Corporation
B-41 L-10, Villa Palao,
Banlic, Calamba City
Laguna 4027,
Philippines
Phone +63 49 3456329
Fax +63 49 3456329
[email protected]
Philippines
Enclosure Systems Specialists Inc
G/F, GE Building
2291 Don Chino Roces Ava Ext
Makati City 1231,
Philippines
Phone +63 2 813 8580
Fax +63 2 813 8596
[email protected]
Poland
Weidmüller Sp. z o.o.
ul. Gol˛edzinowska 10
03-302 Warszawa
Poland
Phone +48 22 5100940
Fax +48 22 5100941
[email protected]
www.weidmuller.pl
Portugal
Weidmüller - Sistemas de
Interface, S. A.
Estrada Outeiro Polima, Lote B,
N° B2, Escritório 2 - Abóboda
2785-518 Sao Domingos de Rana
Lisboa
Phone +351 21 4459190
Fax +351 21 4455871
[email protected]
www.weidmuller.pt
Paraguay
Please contact
CPI S.A., Buenos Aires, Argentina
TW Taiwan
Fittatek Co., Ltd.
12 F No. 185 Fu-Kuo Road,
Tso Ying Dist,
Kaohsiung, Taiwan
Phone +886 7556-0858
Fax +886 7556-3279
[email protected]
TW Taiwan
Eucan Enterprise Ltd.
No. 145 He Ping 2nd Rd
Kaohsiung, Taiwan
Phone +886 7 715 6610
Fax +886 7 715 8748
[email protected]
www.eucan.com.tw
RU Russia
Weidmüller Representative Office
Shabolovka street 2
119049 Moskau, Russia
Phone +7 495 771-6940
Fax +7 495 771-6941
[email protected]
www.weidmueller.ru
UA
Ukraine
TEKO INTERFACE ooo
ul. Lewanewskogo 6
03058 Kiev
Phone +38 044 401 09 90/91/92
Fax +38 044 401 08 64
[email protected]
www.tekointerface.com.ua
SA Saudi Arabia
Saudi Electric Supply Co.
P.O. Box 3298, Al Khobar 31952
Saudi Arabia
Phone +966 3 882-9546227
Fax +966 3 882-9547
[email protected]
US
USA
W-Interconnections, Inc.
821 Southlake Boulevard,
Richmond, VA 23236
Phone +1 804 7942877
Fax +1 804 3792593
[email protected]
www.weidmuller.com
UY
Uruguay
Rewo Uruguay S.A.
AV. Bolivia 2001 Esq Rocafuerte
Carrasco Montevideo
Phone +598 260 4 8439
Fax +598 260 4 8439
[email protected]
SE Sweden
Weidmüller AB
Axel Danielssons väg 271
P.O. box 31025
200 49 Malmö
Phone +46 (0) 7 71 43 00 44
Fax +46 (0) 40 37 48 60
www.weidmuller.se
[email protected]
VE
Venezuela
Somerinca C. A.
Edificio Esteban Piso 2
Calle Vargas Bolleita Notre
Caracas 1070 A
Venezuela
Phone +58 212 2352748
Fax +58 212 2385625
[email protected]
SG Singapore
Weidmüller Pte. Ltd.
70 Bendemeer Road
#04–03 Luzerne
Singapore 339940
Phone +65 6841 5311
Fax +65 6841 5377
[email protected]
www.weidmuller.com.sg
VN
Vietnam
New Sky Co., Ltd
206 Nguyen Thai Binh Str.,
Ward 12., Tan Binh Dist.,
Ho Chin Minh City
Vietnam
Phone +848 811 6768
Fax +848 811 7899
[email protected]
www.newsky-e.com
SA Saudi Arabia
Al Abdulkarim Holding Co.
P. O. Box 4
Dammam 31411
Saudi Arabia
Phone +966 3 833 7110
Fax + 966 3 833 8242
[email protected]
SI
Slovenia
ELEKTROSPOJI d.o.o.
Stegne 25
1000 Ljubljana
Phone +38 6 15113810
Fax +38 6 15111604
[email protected]
YE Yemen
Please contact
Weidmüller Middle-East
United Arab Emirates
ZA
South Africa
Phambili Interface (Pty.) Ltd.
5 Bundo Road
Sebenza Extension
Edenvale 1609
P.O.Box 193
Edenvale 1610
Phone +27 11 452-1930
Fax +27 11 452-6455
[email protected]
DE
Other countries
Weidmüller Interface GmbH & Co. KG
P.O. Box 3030
32720 Detmold
Klingenbergstraße 16
32758 Detmold
Phone +49 5231 14-0
Fax +49 5231 14-20 83
[email protected]
www.weidmueller.com
SK Slovakia
Elektris s.r.o.
Racianska 188
SK 83153 Bratislava, Slovakia
Phone +421 2 49200113
Fax +421 2 44680328
[email protected]
SY
Syria
Please contact
Weidmüller Middle-East
United Arab Emirates
TH
Thailand
Pisanu Engineering Co., Ltd
800/2 Asoke Dindaeng Road,
Dindaeng,
Bangkok 10400
Thailand
Phone +66 2 2459113
Fax +66 2 2463214
[email protected]
www.pisanu.co.th
TR Turkey
Weidmüller Elektronik Ticaret Ltd. Şti.
Kavacik Mah. Mihrabad
Cad. 143/1
.
34810 Beykoz – Istanbul / Turkey
Phone +90 216 5371070 (Pbx)
Fax +90 216 5371077
[email protected]
DE
Group companies
DE
Agency abroad
DE
Without own Agency
41
We cannot guarantee that there are no mistakes in the
publications or software provided by us to the customer for the
purpose of making orders. We try our best to quickly correct
errors in our printed media. For this purpose we list corrections,
which have been identified after publishing printed media, on our
web site at www.weidmueller.com. For convenience we list these
corrections against product catalogue number and/or page
number. This Internet-database is part of our catalogue.
All orders are based on our general terms of delivery, which can
be reviewed on the websites of our group companies where you
place your order. On demand we can also send the general terms
of delivery to you.
42
43
www.weidmueller.com
Argentina
Australia
Austria
Azerbaijan
Bahrain
Belarus
Belgium
BosniaHerzegovina
Brazil
Bulgaria
Canada
Chile
China
Colombia
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Estonia
Finland
France
Germany
Greece
Hong Kong
Hungary
Iceland
India
Indonesia
Iran
Ireland
Israel
Italy
Japan
Jordan
Kazakhstan
Kuwait
Latvia
Lebanon
Lithuania
Luxembourg
Macedonia
Malaysia
Malta
Mexico
Moldova
Montenegro
Netherlands
New Zealand
Norway
Oman
Paraguay
Peru
Philippines
Poland
Portugal
Qatar
Romania
Russia
Saudi Arabia
Serbia
Singapore
Slovakia
Slovenia
South Africa
South Korea
Spain
Sweden
Switzerland
Syria
Taiwan
Thailand
Turkey
UAE
Ukraine
United Kingdom
Uruguay
USA
Venezuela
Vietnam
Yemen
Weidmüller is the leading provider of solutions for the
transmission and conditioning of power, signals and
data in industrial environments. The company develops,
produces and sells products in the field of electrical
connectivity, functional and communication electronics.
For OEM suppliers the company sets international
standards in the engineering, procurement,
manufacturing and distribution of customized
solutions.
Order number:
5660550000/10/2007/SMMD
44