Datasheet WMF 2.5 Terminal Series NEW The WMF 2.5 (multi-functional) terminal series is uniquely designed for DCS marshalling where increased functionality, improved spacing, higher wiring density and ease of terminal installation are desired. The WMF 2.5 series is offered in configuration types including fuse, disconnect and feed-through with pluggable connectors. The WMF 2.5 terminals are 5 mm wide, providing a 20% space savings when compared to typical fuse terminals at 6-8 mm. Applications • DCS marshalling cabinet field wiring • Marshalling terminations that use FTA interface modules via BLZ pluggable connectors • Limited space applications that require multiple shield termination points Benefits • 20% space savings with 5 mm width • Ease of installation via the BLZ pluggable connector (cable harnessing) • Unique fuse holder design simplifies the replacement or installation of fuses • Improved flexibility with unique 3-channel jumpering and integrated shielding Weidmuller, Canada 10 Spy Court Markham, Ontario L3R 5H6 Telephone: (800) 268-4080 Facsimile: (877) 300-5635 Email: [email protected] Website: www.weidmuller.ca Weidmuller, Mexico Blvd. Hermanos Serdán 698, Col. San Rafael Oriente Puebla, Puebla, Mexico C.P. 72029 Telephone: 01 222 2686267 Facsimile: 01 222 2686219 Email: [email protected] Website: www.weidmuller.com.mx Subject to technical changes · 10/12 · 1.5M · LIT1019 Weidmuller, United States 821 Southlake Blvd. Richmond, Virginia 23236 Telephone: (800) 849-9343 Facsimile: (804) 379-2593 Email: [email protected] Website: www.weidmuller.com 1 WMF 2.5 Terminal Series WMF terminals – Weidmuller Multi-Functional The efficient and extremely flexible solution for the routing and distribution of signals In power generation control systems, incoming signals from field devices are often connected with terminal blocks located in DCS marshalling cabinets. Terminal blocks are used in place of, or along with, other termination technologies such as remote I/O modules and Fieldbus. Terminal blocks provide a robust, simple and clean way to connect and arrange signal wires. Weidmuller’s new WMF (Weidmuller Multi-Function) line of terminal blocks is specially designed to improve the way in which DCS marshalling, or signal routing and distribution is performed. This new line provides dramatic cabinet space savings, significant wiring time savings, and additional flexibility through the addition of three cross connection channels. The WMF terminal blocks also feature an integrated shield or ground connection in both the feed through and fuse block terminals, eliminating the need for a separate ground block. The new fuse block design also features disconnect functionality. At only 5mm in width, the WMF blocks are 20% to 25% smaller than traditional feed-through and fuse blocks. Traditional DCS Cabinet Marshalling WMF 2.5 Series DCS Cabinet Marshalling 3 Blocks 18mm Pre-assembled cables 2 Blocks 10mm Marshalling / Routing wiring between internal side of terminal blocks and I/O module or FTA I/O module or Field Terminal Assemblies (FTA) DIN-rail Wire ducts 55% Space Savings Terminal Blocks Marshalling Cabinet 96 Signal Loops / 192 Connections 2 Subject to technical changes · 10/12 · 1.5M · LIT1019 WMF 2.5 Terminal Series Multi-functional terminals WMF 2.5 WMF 2.5 PE 2.5 mm2 Width/Length/height with TS35x7.5 max. current / max. cond. cross-section Max. clamping range mm A/mm2 mm2 2.5 mm2 5.08 x 88 x 45 26 / 4 0.05...4 5.08 x 88 x 45 26 / 4 0.05...4 Technical data Rated data Rated voltage Rated current Rated cross-section Rated impulse voltage / Pollution severity Further technical data solid / stranded "f" with wire end ferrule acc. to DIN 46 228/1 "f" with wire end ferrule with plastic collar Stripping length / Torque range Note V A (mm²) kV/mm² (AWG) (AWG) mm IEC 800 24 UL CSA 600 600 20 20 26…12 AWG (0.05...4) 8 kV/3 IEC 800 24 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated current = 26A (factory wiring only) 20A (factory and field wiring) UL rated voltage = 600V at User Group B, C, D UL CSA 600 600 20 20 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated current = 26A (factory wiring only) 20A (factory and field wiring) UL rated voltage = 600V at User Group B, C, D Ordering data Version Dark beige Wemid Blue Wemid Black Wemid 10 - 36 V AC/DC, with LED 30 - 70 V AC/DC, with LED 60 - 15 V AC/DC, with LED 100 - 250 V AC/DC, with LED Type WMF 2.5 WMF 2.5 BL Qty. 50 50 Part No. 1143070000 1270040000 Type WMF 2.5 PE WMF 2.5 PE BL Qty. 50 50 Part No. 1143060000 1270050000 Version Beige Wemid Type AP WMF2.5 Qty. 1 Part No. 1142990000 Type AP WMF2.5 Qty. 1 Part No. 1142990000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 SD 0.6x3.5x100 1 9008330000 25 25 25 7921560000 7921570000 7921600000 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V 25 25 25 7921560000 7921570000 7921600000 1000 720 1609801044 1792000000 DEK 5 WS 10/5 MC Middle 1000 720 1609801044 1792000000 Note Accessories End plate / partition AP WMF2.5; Pitch = 1.5 mm Mounting block for socket connector Without peg Cross-connection ZQV 2.5N 2-pole 3-pole 10-pole 20-pole Screwdriver SD acc. to DIN 5264-A Component plug (max. 250 V) Holder for cartridge fuse, 5 x 20 mm Without fittings With wire jumper With 1N4007 diode 400 V AC/DC, without LED 10 - 36 V AC/DC, red LED 140 - 250 V AC/DC, red LED Fuse levers for fuse or disconnect terminals Disconnects TNHE ZDL Marking tags DEK WS Isolating plug Disconnect lever only Printout Blank Blank Subject to technical changes · 10/12 · 1.5M · LIT1019 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V DEK 5 WS 10/5 MC Middle Width 6 mm 6 mm 6 mm Width 6 mm 6 mm 6 mm 3 WMF 2.5 Terminal Series Multi-functional terminals Width/Length/height with TS35x7.5 max. current / max. cond. cross-section Max. clamping range WMF 2.5 DI WMF 2.5 DI PE 2.5 mm2 mm A/mm2 mm2 2.5 mm2 5.08 x 88 x 45 19 / 4 0.05...4 5.08 x 88 x 45 19 / 4 0.05...4 Technical data Rated data Rated voltage Rated current Rated cross-section Rated impulse voltage / Pollution severity Further technical data solid / stranded "f" with wire end ferrule acc. to DIN 46 228/1 "f" with wire end ferrule with plastic collar Stripping length / Torque range Note IEC 500 20 V A (mm²) kV/mm² (AWG) (AWG) mm IEC 500 20 UL CSA 600 600 19 19 26…12 AWG (0.05...4) 8 kV/3 UL CSA 600 600 19 19 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages at User Group B, C, D 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages at User Group B, C, D Ordering data Version Dark beige Wemid Blue Wemid Type WMF 2.5 DI WMF 2.5 DI BL Qty. 50 50 Part No. 1143020000 1270070000 Dark beige Wemid Test Socket Black Wemid 10 - 36 V AC/DC, with LED 30 - 70 V AC/DC, with LED 60 - 15 V AC/DC, with LED 100 - 250 V AC/DC, with LED Type WMF 2.5 DI PE WMF 2.5 DI PE BL Qty. 50 50 Part No. 1143030000 1070080000 WMF 2.5 DI PE Stb 50 1167340000 Qty. 1 Part No. 1142990000 Note Accessories End plate / partition AP WMF2.5; Pitch = 1.5 mm Mounting block for socket connector Cross-connection ZQV 2.5N Screwdriver SD acc. to DIN 5264-A Component plug (max. 250 V) Holder for cartridge fuse, 5 x 20 mm Version Beige Wemid TNHE ZDL Test plug Qty. 1 Part No. 1142990000 Type AP WMF2.5 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 SD 0.6x3.5x100 1 9008330000 50 50 50 1833100000 1878570000 1878560000 BEST BEST/DRBR BEST/D 50 50 50 1833100000 1878570000 1878560000 25 25 25 7921560000 7921570000 7921600000 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V 25 25 25 7921560000 7921570000 7921600000 1167630000 1167640000 1167650000 1167670000 1167680000 WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC 1833090000 TNST Without peg 2-pole 3-pole 10-pole 20-pole Without fittings With wire jumper With 1N4007 diode 400 V AC/DC, without LED 10 - 36 V AC/DC, red LED 140 - 250 V AC/DC, red LED Fuse levers for fuse or disconnect terminals Disconnects Type AP WMF2.5 Isolating plug Disconnect lever only BEST BEST/DRBR BEST/D SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V Width 6 mm 6 mm 6 mm WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC TNST 50 Red, PA Marking tags DEK WS 4 Printout Blank Blank 1000 720 1609801044 1792000000 1167630000 1167640000 1167650000 1167670000 1167680000 50 PS 2.3 DEK 5 WS 10/5 MC Middle Width 6 mm 6 mm 6 mm 20 DEK 5 WS 10/5 MC Middle 1000 720 1833090000 0180400000 1609801044 1792000000 Subject to technical changes · 10/12 · 1.5M · LIT1019 WMF 2.5 Terminal Series Multi-functional terminals WMF 2.5 FU WMF 2.5 FU PE 2.5 mm2 Width/Length/height with TS35x7.5 max. current / max. cond. cross-section Max. clamping range mm A/mm2 mm2 2.5 mm2 5.08 x 88 x 72 17 / 4 0.05...4 5.08 x 88 x 72 17 / 4 0.05...4 Technical data Rated data Rated voltage Rated current Rated cross-section Rated impulse voltage / Pollution severity Further technical data solid / stranded "f" with wire end ferrule acc. to DIN 46 228/1 "f" with wire end ferrule with plastic collar Stripping length / Torque range Note IEC 500 6.3 V A (mm²) kV/mm² (AWG) (AWG) mm IEC 500 6.3 UL CSA 600 600 17 17 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltage = 600V at User Group B, C, D UL CSA 600 600 17 17 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltage = 600V at User Group B, C, D Ordering data Version Dark beige Wemid Blue Wemid Black Wemid 10 - 36 V AC/DC, with LED 30 - 70 V AC/DC, with LED 60 - 15 V AC/DC, with LED 100 - 250 V AC/DC, with LED Note Qty. Part No. 1162920000 1162930000 1162940000 1162950000 1162960000 WMF 2.5 FU PE SW 50 WMF 2.5 FU PE 10-36V SW 50 WMF 2.5 FU PE 30-70V SW 50 WMF 2.5 FU PE 60-150V SW 50 WMF 2.5 FU PE 100-250V SW 50 LED versions with low leakage current < 0.5 mA 1163040000 1163050000 1163060000 1163070000 1163080000 Qty. 1 Part No. 1142990000 Type AP WMF2.5 Qty. 1 Part No. 1142990000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 SD 0.6x3.5x100 1 9008330000 25 25 25 7921560000 7921570000 7921600000 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V 25 25 25 7921560000 7921570000 7921600000 1167630000 1167640000 1167650000 1167670000 1167680000 WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC 50 1833090000 4263240000 TNST TNHE ZDL 2.5 GE 1000 720 1609801044 1792000000 DEK 5 WS 10/5 MC Middle Type Qty. Part No. WMF 2.5 FU SW 50 WMF 2.5 FU 10-36V SW 50 WMF 2.5 FU 30-70V SW 50 WMF 2.5 FU 60-150V SW 50 WMF 2.5 FU 100-250V SW 50 LED versions with low leakage current < 0.5 mA Type AP WMF2.5 Type Accessories End plate / partition AP WMF2.5; Pitch = 1.5 mm Mounting block for socket connector Version Beige Wemid Without peg Cross-connection ZQV 2.5N 2-pole 3-pole 10-pole 20-pole Screwdriver SD acc. to DIN 5264-A Component plug (max. 250 V) Holder for cartridge fuse, 5 x 20 mm Without fittings With wire jumper With 1N4007 diode 400 V AC/DC, without LED 10 - 36 V AC/DC, red LED 140 - 250 V AC/DC, red LED Fuse levers for fuse or disconnect terminals Disconnects TNHE ZDL Test plug Isolating plug Disconnect lever only Marking tags DEK WS Subject to technical changes · 10/12 · 1.5M · LIT1019 Printout Blank Blank SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V Width 6 mm 6 mm 6 mm WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC TNST TNHE ZDL 2.5 GE DEK 5 WS 10/5 MC Middle Width 6 mm 6 mm 6 mm 1167630000 1167640000 1167650000 1167670000 1167680000 50 1833090000 4263240000 1000 720 1609801044 1792000000 5 WMF 2.5 Terminal Series Multi-functional terminals Width/Length/height with TS35x7.5 max. current / max. cond. cross-section Max. clamping range WMF 2.5 BLZ mm A/mm2 mm2 Technical data Rated data Rated voltage Rated current Rated cross-section Rated impulse voltage / Pollution severity Further technical data solid / stranded "f" with wire end ferrule acc. to DIN 46 228/1 "f" with wire end ferrule with plastic collar Stripping length / Torque range Note WMF 2.5 BLZ PE 2.5 mm2 V A (mm²) kV/mm² (AWG) (AWG) mm Ordering data Version Dark beige Wemid Black Wemid without lever Dark beige Black Wemid 10 - 36 V AC/DC, with LED 30 - 70 V AC/DC, with LED 60 - 15 V AC/DC, with LED 100 - 250 V AC/DC, with LED Note 2.5 mm2 5.08 x 90 x 45 26 / 4 0.05...4 IEC 250 16 BLZ 5.08 UL CSA 300 300 20 20 26…12 AWG (0.05...4) 8 kV/3 IEC 250 16 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated current = 26A (factory wiring only) 20A (factory and field wiring) 15A (at BLZ plug) Type WMF 2.5 BLZ Qty. 50 BLZ 5.08 5.08 x 90 x 45 26 / 4 0.05...4 UL CSA 300 300 20 20 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated current = 26A (factory wiring only) 20A (factory and field wiring) 15A (at BLZ plug) Part No. 1143050000 Type WMF 2.5 BLZ PE Qty. 50 Part No. 1143040000 Qty. 1 Part No. 1142990000 Type AP WMF2.5 Qty. 1 Part No. 1142990000 1 1142980000 WBB WMF2.5 BLZ 1 1142980000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 SD 0.6x3.5x100 1 9008330000 1000 720 1 1609801044 1792000000 1142970000 UL rated voltages / current: 300V at User Group B 150V / 15A at User Group D 300V / 10A at User Group D Accessories End plate / partition AP WMF2.5; Pitch = 1.5 mm Mounting block for socket connector Cross-connection ZQV 2.5N Screwdriver SD acc. to DIN 5264-A Component plug (max. 250 V)) Holder for cartridge fuse, 5 x 20 mm Version Beige Wemid Type AP WMF2.5 Without peg WBB WMF2.5 BLZ 2-pole 3-pole 10-pole 20-pole Without fittings With wire jumper With 1N4007 diode Width 400 V AC/DC, without LED 10 - 36 V AC/DC, red LED 140 - 250 V AC/DC, red LED Fuse levers for fuse or disconnect terminals Disconnects TNHE ZDL Test plug Width Isolating plug Disconnect lever only Red, PA Marking tags DEK WS WAD cover for unused plug positions 6 Printout Blank Blank DEK 5 WS 10/5 MC Middle WAD WMF2.5 1000 720 1 1609801044 1792000000 1142970000 DEK 5 WS 10/5 MC Middle WAD WMF2.5 Subject to technical changes · 10/12 · 1.5M · LIT1019 WMF 2.5 Terminal Series WMF 2.5 DI BLZ WMF 2.5 DI BLZ PE 2.5 mm2 5.08 x 90 x 45 19 / 4 0.05...4 IEC 250 16 WMF 2.5 FU BLZ 2.5 mm2 2.5 mm2 5.08 x 90 x 45 19 / 4 0.05...4 UL CSA 300 300 19 19 26…12 AWG (0.05...4) 8 kV/3 IEC 250 16 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages / current: 300V at User Group B 150V / 15A at User Group D 300V / 10A at User Group D 15.5A at BLZ plug Type WMF 2.5 DI BLZ WMF 2.5 DI BLZ Stb WMF 2.5 DI BLZ BLK 5.08 x 90 x 72 17 / 4 0.05...4 UL CSA 300 300 19 19 26…12 AWG (0.05...4) 8 kV/3 IEC 250 6.3 Part No. 1143000000 50 50 1357450000 1362940000 Type WMF 2.5 DI BLZ PE WMF 2.5 DI BLZ PE BLK (w/o lever) WMF 2.5 DI BLZ PE Stb Qty. 50 50 50 UL CSA 300 300 17 17 26…12 AWG (0.05...4) 8 kV/3 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages / current: 300V at User Group B 150V / 15A at User Group D 300V / 10A at User Group D 9.5A at BLZ plug 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages / current: 300V at User Group B 150V / 15A at User Group D 300V / 10A at User Group D 15.5A at BLZ plug Qty. 50 BLZ 5.08 Part No. 1143010000 1362930000 1357440000 Type WMF 2.5 FU BLZ SW WMF 2.5 FU BLZ 10-36V SW WMF 2.5 FU BLZ 30-70V SW WMF 2.5 FU BLZ 60-150V SW WMF 2.5 FU BLZ 100-250V SW UL rated current: 14A at BLZ plug Type AP WMF2.5 UL rated current: 14A at BLZ plug Part No. 1142990000 Type AP WMF2.5 1 1142980000 WBB WMF2.5 BLZ ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 9008330000 SD 0.6x3.5x100 1 9008330000 50 50 50 1833100000 1878570000 1878560000 BEST BEST/DRBR BEST/D 50 50 50 1833100000 1878570000 1878560000 25 25 25 7921560000 7921570000 7921600000 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V 25 25 25 7921560000 7921570000 7921600000 SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V 1167630000 1167640000 1167650000 1167670000 1167680000 WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC 1167630000 1167640000 1167650000 1167670000 1167680000 WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC TNST TNHE ZDL 2.5 GE Part No. 1142990000 Type AP WMF2.5 1 1142980000 WBB WMF2.5 BLZ ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 WBB WMF2.5 BLZ BEST BEST/DRBR BEST/D SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V Width 6 mm 6 mm 6 mm WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC Width 6 mm 6 mm 6 mm TNST 50 1833090000 TNST 50 1833090000 PS 2.3 20 0180400000 PS 2.3 20 0180400000 1000 720 1609801044 1792000000 DEK 5 WS 10/5 MC Middle WAD WMF2.5 1000 720 1 1609801044 1792000000 1142970000 DEK 5 WS 10/5 MC Middle Subject to technical changes · 10/12 · 1.5M · LIT1019 Part No. 50 50 50 50 50 1162980000 1162990000 1163000000 1163010000 1163020000 LED versions with low leakage current < 0.5 mA Qty. 1 Qty. 1 Qty. Qty. 1 Part No. 1142990000 1 1142980000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 25 25 25 7921560000 7921570000 7921600000 DEK 5 WS 10/5 MC Middle WAD WMF2.5 Width 6 mm 6 mm 6 mm 1167630000 1167640000 1167650000 1167670000 1167680000 50 1833090000 4263240000 1000 720 1 1609801044 1792000000 1142970000 7 WMF 2.5 Terminal Series Multi-functional terminals WMF 2.5 FU BLZ PE SW BLZP 5.08/90 2.5 mm2 Can be mounted side-by-side without sacrificing any poles 27.2 1.071" 18.9 0.742" L1 + P P L1 14.1 0.555" Ordering data 5.08 x 90 x 72 17 / 4 0.05...4 Technical data Rated data Rated voltage Rated current Rated cross-section Rated impulse voltage / Pollution severity Further technical data solid / stranded "f" with wire end ferrule acc. to DIN 46 228/1 "f" with wire end ferrule with plastic collar Stripping length / Torque range Note IEC 250 6.3 V A (mm²) kV/mm² (AWG) (AWG) mm BLZ 5.08 Version Dark beige Wemid Black Wemid without lever Dark beige Black Wemid 10 - 36 V AC/DC, with LED 30 - 70 V AC/DC, with LED 60 - 15 V AC/DC, with LED 100 - 250 V AC/DC, with LED UL CSA 300 300 17 17 26…12 AWG (0.05...4) 8 kV/3 Component plug (max. 250 V)) Holder for cartridge fuse, 5 x 20 mm Type Qty. WMF 2.5 FU BLZ PE SW WMF 2.5 FU BLZ PE 10-36V SW WMF 2.5 FU BLZ PE 30-70V SW WMF 2.5 FU BLZ PE 60-150V SW WMF 2.5 FU BLZ PE 100-250V SW Version Beige Wemid Type AP WMF2.5 Without peg WBB WMF2.5 BLZ 2-pole 3-pole 10-pole 20-pole L1 + P + 9.8 L1 + P + 0.386" TNHE ZDL Test plug L1 50 50 50 50 50 Part No. 1162820000 1162830000 1162840000 1162850000 1162860000 Part No. 1142990000 1 1142980000 ZQV 2.5N/2 GE ZQV 2.5N/3 GE ZQV 2.5N/10 GE ZQV 2.5N/20 GE 60 60 20 10 1693800000 1693810000 1693880000 1909000000 SD 0.6x3.5x100 1 9008330000 Isolating plug Disconnect lever only SIHA 3/G20 SIHA 3/G20/LD 10-36V SIHA 3/G20/LD 140-250V Width 6 mm 6 mm 6 mm 8 Printout Blank Blank Pitch 5.08 mm Color of plastic Poles L1 mm 2 5.08 4 15.24 8 35.56 12 55.88 16 76.20 (inch) (0.200) (0.600) (1.400) (2.200) (3.000) 25 25 25 7921560000 7921570000 7921600000 1167630000 1167640000 1167650000 1167670000 1167680000 4263240000 TNHE ZDL 2.5 GE 1000 720 1 Orange Black Part No. 1949800000 1949820000 1949860000 1949900000 1949940000 Qty. 90 60 36 24 18 Part No. 1950040000 1950060000 1950100000 1950140000 1950180000 Rated data to IEC 60664-1 / IEC 61984 Clamping range, max. mm² Solid H05(07) V-U mm² Stranded H07 V-R mm² Flexible H05(07) V-K mm² Flexible with ferrule mm² Ferrule with plastic collar mm² Stripping length mm Screwdriver blade mm according to norm 0.2…4 0.2…4 0.2…2.5 7 0.6 x 3.5 DIN 5264 Tightening torque range 0.4 ... 0.5 Rated current at ambient temperature Overvoltage category Pollution severity Rated voltage WMF 2.5 Fuse Lever, w/o indication WMF 2.5 Fuse Lever, LED 10-36VAC/DC WMF 2.5 Fuse Lever, LED 30-70VAC/DC WMF 2.5 Fuse Lever, LED 60-150VAC/DC WMF 2.5 Fuse Lever, LED 100-250VAC/DC DEK 5 WS 10/5 MC Middle WAD WMF2.5 Ordering data Technical data Red, PA Marking tags DEK WS WAD cover for unused plug positions 14.1 0.555" P Qty. 1 Without fittings With wire jumper With 1N4007 diode 400 V AC/DC, without LED 10 - 36 V AC/DC, red LED 140 - 250 V AC/DC, red LED Fuse levers for fuse or disconnect terminals Disconnects Part No. 1948240000 1948260000 1948300000 1948340000 1948380000 With screw flange Accessories Screwdriver SD acc. to DIN 5264-A Black Part No. 1948000000 1948020000 1948060000 1948110000 1948150000 BLZP 5.08/90F 0.5…4 / 1.5…4 0.5…2.5 (26...14) 0.5…2.5 (26...14) 10 / 0.5 - 0.6 UL rated voltages / current: 300V at User Group B 150V / 15A at User Group D 300V / 10A at User Group D 9.5A at BLZ plug LED versions with low leakage current < 0.5 mA Note Cross-connection ZQV 2.5N Orange Poles L1 mm (inch) Qty. 2 5.08 (0.200) 180 4 15.24 (0.600) 90 8 35.56 (1.400) 42 12 55.88 (2.200) 30 16 76.20 (3.000) 18 L1 + P Ordering data End plate / partition AP WMF2.5; Pitch = 1.5 mm Mounting block for socket connector Pitch 5.08 mm Color of plastic 18.9 0.742" mm A/mm2 mm2 27.2 1.071" Width/Length/height with TS35x7.5 max. current / max. cond. cross-section Max. clamping range 1609801044 1792000000 1142970000 Rated impulse voltage a UL 1059 rated data Nominal voltage Rated current AWG conductor r CSA C22.2 rated data Nominal voltage Rated current AWG conductor Material data Type of insulating material Flammability class acc. UL94 Contact base material Material of contact surface 0.13…4 0.2…4 Nm A V 20 °C 15 III 3 250 III 2 320 40 °C 12 II 2 400 kV 4 4 4 V A B 300 15 C D 300 10 V A B 300 10 26–12 C D 300 10 26–12 PBT V-0 Copper alloy tinned Subject to technical changes · 10/12 · 1.5M · LIT1019