KLBÜ shielded connection Contents KLBÜ shielded connection KLBÜ shielded connection Overview shield connection terminals KLBÜ G.2 Shield connection terminals KLBÜ for 10 x 3 mm busbars Clamping yoke G.4 Busbar holders G.6 Shield connection terminals KLBÜ – Mounting directly on metal plate Clamping yoke G.8 Busbar holder / Spacer G.9 Shield connection terminals KLBÜ – Mounting on TS 35 FM 4-foot / Clamping yoke holder G.10 Shield connection terminals KLBÜ for the C profile Clamping yoke G.11 G G.1 KLBÜ shielded connection Overview shield connection terminals KLBÜ The theoretical concept Part 1 of the VDE 0133 standard specifies the required equipotential bonding for the electrical components of a machine. The aim is to prevent any undesirable consequences occurring as a result of electrostatic, electromagnetic and net-work bound interference. G The following measures serve this purpose: • Using filters and time delay devices. • Dividing earth (PE) into “dirty” and “clean”. • Neutral grounding using large earth cables for bonding. • Keeping all bonding leads as short as possible. • Routing all connections parallel to the bonding surface. • Separation and shielding of switching devices and interference sensitive equipment, shielded at one end only. • Shielded lines are used for all motor and all signal connection. These shielded cables for signals are grounded at one end. Drives to Motors should be grounded at both ends. • The mass current is neutral grounded Control Control signals Digital Analogue CNC – GND CNC – GND Position signals KLBÜ SW + SW AGND PSTOP X5 NSTOP DGND I/O ENABLE BTB BTB SHIELD X6 X2 Resolver Booster RESOLVER WPE Power supply unit PC X1 KLBÜ +25 V Mains filter XGND BRAKE PE U2 KLBÜ V2 KLBÜ WPE Mains filter 3 W2 L1 L2 L3 KLBÜ To further servo-amplifiers +DC –DC Overview of KLBÜ fittings available For busbars For direct mounting For C-profiles 10 x 3 G.2 PersonalComputer For TS 35 insulating/conducting Clip-on for 10 x 3 busbar KLBÜ shielded connection Overview shield connection terminals KLBÜ In detail Compression spring No extra tools necessary Full range • To ensure both simple handling and proper connection with permanent contact pressure as a result of the spring effect • Simply swivel onto the busbar by hand – retrospectively if necessary • For conductors from 2 to 37 mm diameter G Reliable contact Many options available • Changes in diameter (flow) of the conductor compensated for by the elastic behaviour of the clamping yoke for flexible adjustment to the cable diameter • Weidmüller offers a wide range of different fastenings for mounting shield connection terminals G.3 KLBÜ shielded connection Shield connection terminals KLBÜ for 10 x 3 mm busbars Clamping yoke Cable fastened against the busbar from below KLBÜ 2 x 2-6 G KLBÜ 3-8 1 2 ! ! ✓ ✗ KLBÜ KLBÜ 4-13.5 KLBÜ 10-20 3 ✓ T KLBÜ 15-32 4 b + 4 mm ✓ Ordering data Type KLBÜ 2 x 2-6 b For cable diameter 2.0 ... 6.0 mm Dimensions (a x b x c) mm 15.0 x 18.0 x 24.0 Qty. 10 Order No. 1675350000 KLBÜ 3-8 KLBÜ 4 x 13.5 KLBÜ 10-20 3.0 ... 8.0 mm 4.0 ... 13.5 mm 10.0 ... 20.0 mm 13.0 x 18.0 x 26.0 20.0 x 20.5 x 31.5 25.0 x 26.0 x 40.0 10 10 10 1600480000 1592810000 1600490000 KLBÜ 15-32 15.0 ... 32.0 mm 36.0 x 32.0 x 63.9 10 1716300000 c a Marking on the product: Marking EN 50019: Marking EX-RL 94/9/EC: T T Ex e II II 2 G D EC type testing certificate: DMT 02 ATEX E 024 U G.4 10 x 3 mm busbars SSch 10 x 3 x 1000 Cu, Sn, Pb Length 1000.0 mm Material Cu, Sn, Pb Qty. 1 Order No. 0348900000 SSch 10 x 3 x 1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000 KLBÜ shielded connection Shield connection terminals KLBÜ for 10 x 3 mm busbars Clamping yoke Cable fastened onto the busbar from above KLBÜ CO 1 KLBÜ CO 2 1 2 ! ! ✓ ✗ KLBÜ CO KLBÜ CO 4 KLBÜ CO 5 3 ✓ T a + 4 mm G ✓ Ordering data c b Type KLBÜ CO 1 For cable diameter 3.0 ... 10.0 mm KLBÜ CO 2 KLBÜ CO 3 KLBÜ CO 4 4.0 ... 15.0 mm 10.0 ... 20.0 mm 15.0 ... 28.0 mm KLBÜ CO 5 20.0 ... 37.0 mm Dimensions (a x b x c x d) mm 18.0 x 12.0 x 13.2 x 32.0 Qty. 10 Order No. 1753311001 18.0 x 20.0 x 21.1 x 41.6 25.0 x 23.0 x 24.0 x 45.0 25.0 x 31.0 x 32.0 x 56.0 10 10 10 1752131001 1749151001 1749161001 32.0 x 40.0 x 42.7 x 64.5 10 1755081001 Qty. 1 1 Order No. 0348900000 1746130000 d a KLBÜ CO 3 10 x 3 mm busbars SSch 10 x 3 x 1000 Cu, Sn, Pb SSch 10 x 3 x 1000 Fe, Zn, 8B Marking on the product: Marking EN 50019: Marking EX-RL 94/9/EC: Length 1000.0 mm 1000.0 mm Material Cu, Sn, Pb Fe, Zn, 8B T T Ex e II II 2 G D EC type testing certificate: DMT 02 ATEX E 024 U G.5 KLBÜ shielded connection Shield connection terminals KLBÜ for 10 x 3 mm busbars Busbar holders Insulated mounting on TS 35 Type WSH 1 Type WSH 3/H/N Horizontal mounting only G Type WSH 5 WSH EC type testing certificate: DMT 02 ATEX E 024 U Type WSH 6 Ordering data Type WSH 1 Width 8.0 mm Qty. 10 Order No. 1068700000 WSH 3/H/N WSH 5 8.0 mm 8.0 mm 10 10 1715970000 1080100000 WSH 6 8.0 mm 10 1080200000 Qty. Order No. 0348900000 10 x 3 mm busbars SSch 10 x 3 x 1000 Cu, Sn, Pb G.6 Length 1000.0 mm Material Cu, Sn, Pb 1 KLBÜ shielded connection Shield connection terminals KLBÜ for 10 x 3 mm busbars Busbar holders Conductive mounting on TS 35 TS 35-Clip BS 35/WSH 2 Busbar connector BFEH 1/WSH Installation example 1 • One busbar • 2 x WSH 19 MT busbar holder set WSH EC type testing certificate: DMT 02 ATEX E 024 U Angled rail SMSE WSH U1MT G Installation example 2 • Two busbars • 2 x WSH 18 MT busbar holder set Ordering data TS 35-Clip BS 35/WSH 2 Dimensions (L x B x H) mm 52.0 x 37.0 x 13.0 Qty. 10 Order No. 1760720000 Busbar connector Dimensions (L x B x H) mm Qty. 20.0 x 31.0 x 13.5 10 Order No. 1082400000 Dimensions (L x B x H) mm 134.0 x 13.0 x 134.0 Qty. 10 Order No. 1083900000 Qty. 10 Order No. 1083100000 BFEH 1/WSH Angled rail SMSE WSH U1MT Busbar holder sets WSH 18 MT Contents (parts loose in plastic bag) BS 35/WSH 2 BFEH 1/WSH SMSE WSH U1MT 1 ea. 2 ea. 2 ea. WSH 19 MT 1 ea. 1 ea. 1 ea. 10 1083200000 WSH 20 MT 1 ea. 1 ea. 1 ea. (straight) 10 1752950000 10 x 3 mm busbars SSch 10 x 3 x 1000 Cu, Sn, Pb Length 1000.0 mm Material Cu, Sn, Pb Qty. 1 Order No. 0348900000 SSch 10 x 3 x 1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000 G.7 KLBÜ shielded connection Shield connection terminals KLBÜ – Mounting directly on metal plate Clamping yoke KLBÜ 3-8 SC KLBÜ 4-13.5 SC 1 KLBÜ 10-20 SC 2 KLBÜ 15-32 SC 3 Drilling template KLBÜ 15-32 SC ø 4.2 mm M4 ! G a>b=✓ a<b=✗ 10 mm ! ✗ ✓ ✓ T c + 4 mm ✓ b a KLBÜ SC ! Ordering data Type KLBÜ 3-8 SC c For cable diameter 3.0 ... 8.0 mm Thread length 5.65 mm KLBÜ 4-13.5 SC KLBÜ 10-20 SC 4.0 ... 13.5 mm 10.0 ... 20.0 mm 5.30 mm 5.30 mm KLBÜ 15-32 SC 15.0 ... 32.0 mm 4.80 mm Dimensions (a x b x c) mm 13.5 x 11.5 x 18.0 x 26.0 Qty. 10 Order No. 1692261001 20.0 x 17.8 x 20.3 x 31.4 24.8 x 23.0 x 26.0 x 40.0 10 10 1712311001 1712321001 36.0 x 33.3 x 32.0 x 64.0 10 1718341001 Qty. Order No. 1742630000 e d a b Marking on the product: Marking EN 50019: Marking EX-RL 94/9/EC: T T Ex e II II 2 G D EC type testing certificate: DMT 02 ATEX E 024 U G.8 Operating tool BTWZ KLBÜ 1 Busbar holder / Spacer Busbar holder 28 Set (WSH 4 MT) consisting of: – 1 busbar holder – 1 busbar connector (BFEH 1/WSH) 70 10 x 3 KLBÜ shielded connection Shield connection terminals KLBÜ – Mounting directly on metal plate 12 Mounting plate 40.5 ø Du for M 5 ø = 5.2 mm Spacer M6 outer and inner thread (15 mm, 20 mm and 30 mm long) G WSH 4 MT / SP EC type testing certificate: DMT 02 ATEX E 024 U Ordering data Busbar holder WSH 4 MT Qty. 10 Order No. 1079900000 Type SP 15, set of 2 Length 15 mm Qty. 1 Order No. 3896100000 SP 20, set of 2 20 mm 1 3896200000 SP 30, set of 2 30 mm 1 3896300000 G.9 KLBÜ shielded connection Shield connection terminals KLBÜ – Mounting on TS 35 FM 4 foot / Clamping yoke holder FM 4 foot The KLBÜ SC clamping yokes (see page G.8) are screwed onto the FM 4 foot. Clamping yoke holder G BS 35 II (without KLBÜ) FM 4 / BS 35 II BS 35 II / KLBÜ 3-8 BS 35 II / KLBÜ 3-8 / 2 x 2-6 Ordering data FM 4 foot FM 4 Qty. 40 Order No. 0687900000 For cable diameter without KLBÜ Qty. 10 Order No. 1723800000 BS 35 II / KLBÜ 3-8 BS 35 II / KLBÜ 4-13.5 BS 35 II / KLBÜ 3-8/2 x 2-6 3.0 ... 8.0 mm 4.0 ... 13.5 mm 3.0 ... 8.0 mm / 2.0 ... 6.0 mm 10 10 10 1723810000 1723820000 BS 35 II / KLBÜ 2 x 3-8/2 x 2-6 3.0 ... 8.0 mm / 2.0 ...6.0 mm 10 1768020000 Clamping yoke holder BS 35 II Marking on the product: Marking EN 50019: Marking EX-RL 94/9/EC: T T Ex e II II 2 G D EC type testing certificate: DMT 02 ATEX E 024 U G.10 1749430000 KLBÜ shielded connection KLBÜ shielded connection terminals for the C profile Clamping yoke KLBÜ 3-8 CPF KLBÜ 4-13.5 CPF KLBÜ 10-20 CPF KLBÜ 15-32 CPF G Ordering data Type KLBÜ 3-8 CPF c For cable diameter 3.0 ... 8.0 mm Dimensions (a x b x c x d) mm 13.5 x 11.5 x 18.0 x 26.0 Qty. 10 Order No. 1752681001 KLBÜ 4-13.5 CPF KLBÜ 10-20 CPF 4.0 ... 13.5 mm 10.0 ... 20.0 mm 20.0 x 17.8 x 20.3 x 31.4 24.8 x 23.0 x 26.0 x 40.0 10 10 1752691001 1752701001 KLBÜ 15-32 CPF 15.0 ... 32.0 mm 36.0 x 33.3 x 32.0 x 64.0 10 1752711001 Qty. Order No. 1802690000 e d KLBÜ CPF a b C-rail TS 27 x 12.5M / ST / F.ZN Marking on the product: Marking EN 50019: Marking EX-RL 94/9/EC: 10 m T T Ex e II II 2 G D EC type testing certificate: DMT 02 ATEX E 024 U G.11 G G.12 KLBÜ shielded connection