Humidity Sensor Temperature/Humidity Sensor ES2-HB ES2-THB CSM_ES2-HB_ES2-THB_DS_E_3_3 Detect Humidity within an Accuracy of ±3% in a Compact Body. Controller Set Provides Superior Humidity Control and Temperature/ Humidity Control. • Employs high-polymer-resistive Sensor with superior durability. • Compact and lightweight. • Measurement ranges of 20% to 95% for humidity and 0 to 55°C for temperature. Ordering Information Name Model Humidity Sensor ES2-HB Temperature/Humidity Sensor ES2-THB Dimensions Note: All units are in millimeters unless otherwise indicated. ES2-HB Humidity Sensor ES2-THB Temperature/Humidity Sensor Humidity Sensor Module (See note.) ES2-M Note: This is a replacement item. One Module is provided with the ES2-HB/-THB. Always attach the Humidity Sensor Module when using the ES2-HB/-THB. Approximately 7 VDC will be output for the humidity output if the Module is not attached or is incompletely attached. 22 50 50 Specifications Humidity Sensor section High-polymer resistive 5.5 dia. Humidity detection range 20 to 95% Humidity detection accuracy ±3% (25°C, 40 to 80%) Shield wire in transparent tube Shield 5,000 ± 200 Power supply voltage 24 VDC (See note 1.) (25) White Operating voltage range 85% to 110% of power supply voltage OUT Current consumption 10 mA max. Humidity output Temperature Sensor Section (See note 2.) Black G 1 to 5 V (for humidity of 0% to 100%) Permissible load impedance: 100 kΩ min. (Use a 1:1 connection when connecting to an E5CC/E5EC/E5AC.) Platinum resistance thermometer Red IN Heat-shrinking tube 150 ± 20 Cover 4 dia. Temperature detection range 0 to 55°C Temperature output Pt100: 3 wire (See note 4.) Class JIS class B Humidity signal 37 37 Communications cable length 5 m Operating temperature 0 to 55°C, humidity of 95% max. and humidity range (See note 3.) Storage temperature and humidity range (See note 3.) −20 to 60°C, humidity of 95% max. Degree of protection IP 20 equivalent Weight ES2-HB: Approx. 41 g (excluding cables) ES2-THB: Approx. 43 g (excluding cables) Note: 1. The maximum ripple voltage of 2% p-p max. The recommended power supply is the OMRON S8JX or S8VS. 2. ES2-THB only. 3. Do not use or store the Sensor for an extended period at a humidity of 90% or more. 4. Pt100 (JIS C 1604-1989) is used for the measuring elements. Set Pt100 for input sensor type of the Temperature Controller. 4 dia. ES2-M Humidity Sensor Module 21 12.7 17.5 Note: Firmly insert the connector all the way in when mounting the ES2-M to the Sensor. 1 ES2-HB ES2-THB Precautions for Safe Use Do not use the product in the following locations: • • • • Locations subject to water splashing or oil contact Locations subject to dust or corrosive gases Locations subject to icing or condensation Locations subject to direct sunlight Connection Examples ES2-HB Humidity Sensor ES2-THB Temperature/Humidity Sensor ES2-THB ES2-HB Yellow Green Brown Controller or PT White White + A B B + 1 to 5 V − − Red Black Red 24 VDC DC power supply Black GND Temperature input (platinum resistance thermometer) Controller or PT Humidity input (1 to 5 V) Controller or PT 24 VDC DC power supply GND Shield (Ground separately.) Shield (Ground separately.) Cable Conditions Item Model ES2-HB ES2-THB Diameter AWG22 AWG24 Number of conductors 3 6 Shield Braided Braided Maximum conductive resistance (20°C) 60 Ω/km max. 92 Ω/km max. Finished outer cable diameter 5.8 mm 5.1 mm Note: Provide a separate cable according to the details listed at the left if the length of the supplied cable is insufficient. The cable can be extended to a maximum of 50 m. 2 ES2-HB ES2-THB Application Examples Temperature and humidity control for vegetable and fruit growing rooms Monitoring and data collection for clean rooms and storage locations Digital Controller ES2-HB ES-THB Alarm lamp Buzzer Recorder Factories and clean rooms Air conditioner Humidifier Heater Temperature Controller Digital Controller Humidity control for constant-humidity warehouses and rooms for fermentation or ripening ES2-HB Temperature and humidity control for drying Recorder Humidifier or dehumidifier Digital Controller Office Dehumidifier Temperature Digital Controller Controller Warehouse Humidity control for plant factories and greenhouses ES2-THB Exit side ES2-HB Dry air Sirocco fan Heater Exit Entrance Digital Panel Meter Recorder Office Humidifier or dehumidifier Growing bed Digital Controller Plastic greenhouse ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice. 3 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2016.5 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2016 All Right Reserved.