EV-ADF5904SD2Z User Guide UG-791 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for the ADF5904 4-Channel, 24 GHz Receiver Downconverter FEATURES GENERAL DESCRIPTION Contains ADF5904 4-channel, 24 GHz receiver downconverter Accompanying software allows control of ADF5904 functions from a PC The EV-ADF5904SD2Z evaluation board allows the user to evaluate the performance of the ADF5904 24 GHz receiver downconverter. Figure 1 shows the board, which contains the ADF5904, five high frequency SMA connectors for the local oscillator (LO) input, four receiver (Rx) inputs, eight SMA connectors for the baseband outputs, banana connectors for power supply, and a connector for serial interface. EVALUATION KIT CONTENTS EV-ADF5904SD2Z evaluation board ADDITIONAL EQUIPMENT The evaluation kit also contains software that is compatible with Windows® XP and later versions to allow easy programming of the device. PC running Windows XP or more recent version Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration platform-serial (SDP-S) board Spectrum analyzer (optional) Oscilloscope 5 V power supplies USB cable This evaluation board requires an EVAL-SDP-CS1Z SDP-S board (not supplied with the kit). The SDP-S board allows software programming of the ADF5904 device. Full specifications on the ADF5904 are available in the product data sheet, which should be consulted in conjunction with this user guide when working with the evaluation board. DOCUMENTS NEEDED ADF5904 data sheet REQUIRED SOFTWARE Analog Devices ADF5904 Software 12895-001 EVALUATION BOARD PHOTOGRAPH Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 14 UG-791 EV-ADF5904SD2Z User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Power Supplies ...............................................................................4 Evaluation Kit Contents ................................................................... 1 Input Signals...................................................................................4 Additional Equipment ..................................................................... 1 Output Signals ...............................................................................4 Documents Needed .......................................................................... 1 Default Operation .........................................................................4 Required Software ............................................................................ 1 Evaluation Board Software ...............................................................5 General Description ......................................................................... 1 Evaluation and Test ...........................................................................7 Evaluation Board Photograph......................................................... 1 Evaluation Board Schematics and Artwork ...................................8 Revision History ............................................................................... 2 Ordering Information .................................................................... 13 Quick Start Guide ............................................................................. 3 Bill of Materials ........................................................................... 13 Evaluation Board Hardware ............................................................ 4 Related Links ................................................................................... 13 REVISION HISTORY 3/15—Revision 0: Initial Version Rev. 0 | Page 2 of 14 EV-ADF5904SD2Z User Guide UG-791 QUICK START GUIDE Follow these steps to quickly evaluate the ADF5904. 1. 2. 3. 4. 5. 6. Connect the power supply to the EV-ADF5904SD2Z: a. 5 V to Banana Connector P2 b. GND to Banana Connector P1 Install the ADF5904 software. Connect the SDP-S motherboard to the PC and to the EV-ADF5904SD2Z evaluation board. Follow the hardware driver installation procedure. Run the ADF5904 software. Select the ADF5904 device and the USB board in the Select Device and Connection tab of the software front panel window (see Figure 2). 7. Check that the message SDP board connected appears at the bottom left of the software window (see Figure 2). 8. Connect an ac-coupled RF source to LOIN SMA and connect an ac-coupled RF source to one of the RXxIN input SMAs. 9. In the Main Controls tab, click Initialize. 10. Connect the corresponding Rx baseband channel output to an oscilloscope. 11. Measure the results. Rev. 0 | Page 3 of 14 UG-791 EV-ADF5904SD2Z User Guide EVALUATION BOARD HARDWARE The evaluation board requires an SDP-S motherboard to program the device. The SDP-S board is not included and must be purchased separately. The EV-ADF5904SD2Z schematics are shown in Figure 5 to Figure 9. The top layer and assembly layout are shown in Figure 10. POWER SUPPLIES The evaluation board is powered via one external supply, 5 V connected as described in the Quick Start Guide section. INPUT SIGNALS The LO input pin and the Rx input pins on the ADF5904 contain a dc bias voltage; the inputs must be ac-coupled to the evaluation board. OUTPUT SIGNALS The baseband outputs from the ADF5904 contain dc bias voltages and are available on the J3 to J11 output SMAs. Table 1. Baseband Output Mapping Rx Input RF1IN RF2IN RF3IN RF4IN Baseband Outputs J3, J4 J6, J7 J8, J9 J10, J11 DEFAULT OPERATION All components necessary for ADF5904 operation are inserted on the board. Rev. 0 | Page 4 of 14 EV-ADF5904SD2Z User Guide UG-791 EVALUATION BOARD SOFTWARE The control software for the EV-ADF5904SD2Z is included in the evaluation kit on a CD. To install the software, follow the on-screen instructions. To run the software, click the ADF5904 file on the desktop or from the Start menu. Note that, when connecting the board, it takes approximately 5 sec to 10 sec for the status label to change. 12895-002 In the Select Device and Connection tab, select the device and the connection method, and click Connect. Confirm that Analog Devices Eval Board connected is displayed at the bottom left of the window (see Figure 2). Otherwise, the software has no connection to the evaluation board. Figure 2. Software Front Panel Display—Select Device and Connection Rev. 0 | Page 5 of 14 UG-791 EV-ADF5904SD2Z User Guide The Main Controls tab controls the ADF5904 device settings (see Figure 3). 12895-003 This tab allows the user to select general options available for the ADF5904, including power up/down control and register readback. On initial power-up of the device, click the Initialize button to perform the initialization sequence as described in the ADF5904 data sheet. Figure 3. Software Front Panel Display—Main Controls Rev. 0 | Page 6 of 14 EV-ADF5904SD2Z User Guide UG-791 EVALUATION AND TEST To evaluate and test the performance of the ADF5904, take the following steps: 2. 3. 4. 5. Install the SDP-S software drivers. Connect the evaluation board to a PC using the supplied USB cable. Follow the hardware driver installation procedure that appears. Connect the SDP-S connector to the EV-ADF5904SD2Z. Install the ADF5904 software. Connect an ac-coupled RF signal to LOIN SMA. Connect an ac-coupled RF signal to the RX1IN input SMA. Connect a 1 MΩ, ac-coupled oscilloscope to the J3 and J4 output SMAs. 7. Run the ADF5904 software. 8. Select the SDP-S board and the ADF5904 device in the Select Device and Connection tab of the software window. 9. In the Main Controls tab, click Initialize to power up the ADF5904 (see Figure 3). See Figure 4 for the suggested setup. 10. Measure the baseband output signals. SDP-S ADAPTOR BOARD PC SIGNAL SOURCE OSCILLOSCOPE DC BLOCK SIGNAL SOURCE +5V 12895-004 1. 6. POWER SUPPLY Figure 4. Typical Evaluation Setup Rev. 0 | Page 7 of 14 UG-791 EV-ADF5904SD2Z User Guide EVALUATION BOARD SCHEMATICS AND ARTWORK J3 RF1IN RX1_RF 1 RX1_BBO BLOCK2 2 3 RX1_RFIN RX1_BBO RX1_BBOB RX1_BBO RX1_BBOB RX2_BBO RX2_BBOB RX2_BBO RX2_BBOB RX3_BBO RX3_BBOB RX3_BBO RX3_BBOB J4 RX2_RFIN RF2IN RX2_RF 1 RX3_RFIN 2 3 RX4_RFIN RX1_BBOB J6 RX2_BBO RX4_BBO RX4_BBOB LO_RFIN CE RX4_RF J2 RX2_BBOB ATEST DATA CE DOUT TP1 DOUT CLK LO_AHI RF4IN J7 TP4 J8 RX3_BBO TP3 DATA RX4_BBO RX4_BBOB LE RX34_AHI LE CLK TP2 2 3 RX12_AHI RF3IN RX3_RF 1 J9 0 R3 0 R2 R1 2 3 0 RX3_BBOB LOIN LO_IN 1 AVDD J10 AVDD INTERFACE RX4_BBO CLK DATA LE CE DOUT CLK DATA LE CE DOUT AVDD AVDD J11 RX4_BBOB AVDD P1 AGND POWER P2 VDD J1 12895-005 AVDD1 Figure 5. Evaluation Board Schematic (Page 1) Rev. 0 | Page 8 of 14 EV-ADF5904SD2Z User Guide UG-791 R19 8.2K R20 10K AVDD IO 0 R16 TP5 TP9 1 1 R4 330 LE R9 CE IO IO 330 TP8 TP6 1 1 R8 CLK DOUT DATA R18 R10 0 330 IO IO IO 1 Figure 6. Evaluation Board Schematic (Page 2) Rev. 0 | Page 9 of 14 12895-006 DGND 10K 390 R17 R15 390 R14 390 TP7 390 330 R12 GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 SPI_SEL_A SPI_SEL_B SPI_SEL_C SPI_CLK SPI_MISO SPI_MOSI R11 SDP-S 0 R13 DGND Rev. 0 | Page 10 of 14 Figure 7. Evaluation Board Schematic (Page 3) IO SPI_SEL_B IO SPI_SEL_C IO GPIO0 IO GPIO2 IO GPIO4 IO GPIO6 DGND R6 TBD0603 1 J5 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 FX8-120S-SV(21) R5 100K R7 100K J5 1 2 3 6 7 VIO DGND U3 8 A0 VCC EEPROM A1 A2 SDA 5 SCL WP VSS 4 24LC32A-I/MS IO SPI_SEL_A IO SPI_MOSI IO SPI_MISO IO SPI_CLK IO GPIO1 IO GPIO3 IO GPIO5 IO GPIO7 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 FX8-120S-SV(21) 12895-007 UG-791 EV-ADF5904SD2Z User Guide EV-ADF5904SD2Z User Guide UG-791 IO 6 GND EN 4.7UH 0 3 GND PAD AVDD IO 2 4 NC 12895-008 AGND AGND 1UF C12 PAD R23 AGND SENSE 1UF C10 1N4001 C D1 A AGND 5 PG R25 1 R24 0 L1 VOUT 1UF 7 ADP7104 VIN C11 8 R22 MBR0540T1G R21 0 C 0 IO A 0 U2 D2 VDD 0 R26 AVDD1 AGND AGND IN IN IN IN IN IN Figure 8. Evaluation Board Schematic (Page 4) IN AGND IN RX1_RFIN RX12_AHI RX3_BBO 25 RX3_BBOB LO_AHI 27 26 LO_RFIN 28 29 30 23 3 22 21 4 RX2_RFIN RX2_BBO 5 20 6 19 7 18 8 17 RX3_RFIN RX34_AHI RX4_RFIN RX4_BBOB IN IN IN IN 16 RX4_BBO ATEST 14 DOUT 15 13 12 CE DATA 11 CLK 9 RX2_BBOB C9 C4 12895-009 IN IN IN IN IN IN 10PF IN C2 LO_AHI 100PF 2 10PF AGND 1000PF IN 24 IN 100PF C5 C3 C1 IN 1 ADF5904 RX34_AHI 1000PF RX1_BBO 10PF LE 100PF U1 C8 10 1000PF C7 31 PAD C6 32 RX1_BBOB AGND RX12_AHI AGND Figure 9. Evaluation Board Schematic (Page 5) Rev. 0 | Page 11 of 14 EV-ADF5904SD2Z User Guide 12895-010 UG-791 Figure 10. Layer 1 (Component Side) Rev. 0 | Page 12 of 14 EV-ADF5904SD2Z User Guide UG-791 ORDERING INFORMATION BILL OF MATERIALS Table 2. Qty 3 3 3 1 1 10 1 1 5 1 1 3 4 1 1 1 2 1 9 1 1 2 2 1 4 1 1 1 1 1 1 1 5 Reference Designator C1, C2, C6 C3, C4, C7 C5, C8, C9 D1 D2 J1 to J4, J6 to J11 J5 L1 LOIN, RF1IN to RF4IN P1 P2 R4, R8, R10 R11, R12, R14, R15 R17 R19 R20 R5,R7 R6 TP1 to TP9 U2 U3 Screw1, Screw2 Nut1, Nut2 U1 R21, R22, R25, R26 R24 R23 C12 C11 C10 R16 R9 R1, R2, R3, R13, R18 Description 0.1 μF capacitor 1000 pF capacitor 10 pF capacitor Diode Diode Connector, PCB, end launch, SMA 120-way connector, 0.6 mm pitch 4.7 μH inductor 2.92 mm Rosenberger connectors Black, 4 mm, banana socket Red, 4 mm, banana socket 330 Ω resistor 390 Ω resistor 10 kΩ resistor 8.2kΩ resistor 10 kΩ resistor 100 kΩ resistor Do not populate Connector, PCB, test point, red Linear regulator, 3.3 V, 20 V, 500 mA, ultralow noise 32k, I2C, serial EEPROM, MSOP8 Screw, cheese, nylon Nut/washer, nylon ADF5904 Rx MMIC 0 Ω resistor 0.33 Ω resistor Do not populate 100 μF capacitor 10 μF capacitor 1 μF capacitor Do not populate Do not populate 0 Ω resistor RELATED LINKS Resource ADF5904 ADP7104 Description Product Page, 4-Channel, 24 GHz, Receiver Downconverter Product Page, 20 V, 500 mA, Low Noise, CMOS LDO Rev. 0 | Page 13 of 14 Manufacturer AVX Murata AVX Multicomp On Semiconductor Emerson Hirose Coilcraft Rosenberger Deltron Deltron Vishay Multicomp Multicomp Multicomp Multicomp Yageo (Phycomp) Not applicable Keystone Electronics Corp Analog Devices Microchip Allthread Duratool Analog Devices Multicomp Welwyn Not applicable Kemet Murata Taiyo/Yuden Not applicable Not applicable Multicomp Part Number 06033C104JAT2A GRM1555C1H102JA01 04025U100GAT2A 1N4001 MBR0520LT1G 142-0701-851 FX8-120S-SV(21) EPL2014-472ML 02K243-40M 571-0100 571-0500 CRCW0603330RFKEA MC 0.063W 0603 390R MC 0.063W 0603 10K MC 0.063W 0603 1% 8K2 MC 0.063W 0603 10K RC0402JR-07100KL Not applicable 5000 ADP7104ARDZ-3.3 24LC32A-I/MS 119030010 1140030 ADF5904BCPZ MC 0.0625W 0402 1% 0R LRCS0402-0R33FT5 Not applicable T520B107M006ATE040 GRM21BR61A106KE19L TMK107BJ105KA-T Not applicable Not applicable MC 0.063W 0603 0R UG-791 EV-ADF5904SD2Z User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG12895-0-3/15(0) Rev. 0 | Page 14 of 14