SIDACtor ® Protection Thyristors High Surge Current Protection SIDACtor® Primary Protection Balanced Series - Modified TO-220 Description The SIDACtor® Primary Protection Balanced Series Modified TO-220 are thyristor devices designed for use in primary protection applications. The series provides a single port overvoltage solution that enables applications to comply with the balance requirements of GR-974 and GTS-8700. Please contact Littelfuse to discuss your particular application and regulatory requirements. Features and Benefits Agency Approvals t High holding current options available t Does not degrade with use Agency Agency File Number t Balanced overvoltage protection E133083 t Failsafe option available t Fails short circuit when surged in excess of ratings t Low voltage overshoot t Single-port protection Pinout Designation t Modified TO-220 Package t Low on-state voltage t Lead forms available Applicable Global Standards PIN 1 PIN 3 t GR-974 t UL 497 t GTS-8700 t ITU K.28 PIN 2 Schematic Symbol 1 3 (T) (R) 2 (G) Electrical Characteristics Part Number P1553ACLxx P1803ACLxx P2103ACLxx P2353ACLxx P2703ACLxx P3203ACLxx P3403ACLxx P5103ACLxx Marking P1553AC P1803AC P2103AC P2353AC P2703AC P3203AC P3403AC P5103AC VS VDRM @lDRM=5μA @100V/μs V min V max Pins 1-2, 3-2, 1-3 130 180 150 210 170 250 200 270 230 300 270 350 300 400 420 600 IH* IS IT VT@IT= 2.2 Amps mA min mA max A max V max 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 8 Notes: * Higher holding current available by special order. Contact Littelfuse for additional information. - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Capacitance Pin 1-2 / 3-2 Tip-Ground, Ring-Ground pF min 65 55 55 50 50 45 45 40 pF max 95 85 85 75 75 70 65 60 Pin 1-3 Tip-Ring pF min 40 35 30 30 30 25 25 20 pF max 60 55 55 50 50 45 45 40 - Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. - xx Part Number Suffix: ‘RP’ (Reel pack), Blank (Bulk pack), ‘60’ (Type 60 lead form bulk pack), ‘FS1’ (Failsafe option bulk pack). Refer to Part Numbering section for additional details. 199 Revised: February 22, 2011 SIDACtor ® Protection Thyristors High Surge Current Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/μs max 200 50 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 C Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 50 °C/W Modified TO-220 PIN 1 PIN 3 PIN 2 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0 -4 -6 -8 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -40 Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 200 Revised: February 22, 2011 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Numbering P xxx 3 A C L xx PACKING OPTIONS TYPE Blank: Bulk RP: Reel Pack 60: Type 60 Lead Form (for type 60 orders, contact factory). P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE RoHS COMPLIANT PACKAGE TYPE IPP RATING Part Marking XXXXXXXXX (Refer to Electrical Characteristics Table) P xxx 3 A C L FS1 TYPE xxxxx FAILSAFE OPTION* P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE RoHS COMPLIANT IPP RATING * Failsafe devices are only offered in bulk pack, reel pack not available. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code 201 Revised: February 22, 2011 Date Code SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions - Modified TO-220 A Inches O D Temperature Measurement Point F G Dimensions - Modified TO-220 with Failsafe P PIN 3 PIN 2 PIN 1 L M K H N J The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. Millimeters Min Max Min A 0.400 0.410 10.16 10.42 Max D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 0.89 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 Tape and Reel Specification - Modified TO-220 0.240 (6.10) Dimensions - Modified TO-220 Type 60 with Failsafe 0.019 (0.5) 1.626 (41.15) 0.750 ± 0.010 (19.05 ± 0.25) 0.720 (18.29) 0.360 (9.14) 0.500 (12.7) 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Packing Options Package Type A Description Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B Modified TO-220 Bulk Pack 500 (no added suffix) N/A Modified TO-220 Type 60 Lead Form Bulk Pack 500 60 (special order item, contact factory for details) N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 202 Revised: February 22, 2011