SIDACtor ® Protection Thyristors Broadband Optimized™ Protection MC Series - DO-214 Description MC Series DO-214 are low capacitance SIDACtor® devices designed to protect broadband equipment such as VOIP, DSL modems and DSLAMs from damaging overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features and Benefits t Low voltage overshoot t Low on-state voltage Agency Approvals t Does not degrade with use Agency t Fails short circuit when surged in excess of ratings Agency File Number E133083 t 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Applicable Global Standards Pinout Designation NOT APPLICABLE Schematic Symbol t TIA-968-A t GR 1089 Intra-building* t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level* t YD/T 1082 t ITU K.20/21 Basic Level* t YD/T 950 t YD/T 993 t GR 1089 Inter-building* *A-rated parts require series resistance Electrical Characteristics Part Number P0080SAMCLRP P0220SAMCLRP P0300SAMCLRP P0080SCMCLRP P0220SCMCLRP P0300SCMCLRP P0640SCMCLRP P0720SCMCLRP P0900SCMCLRP P1100SCMCLRP P1300SCMCLRP P1500SCMCLRP P1800SCMCLRP P2100SCMCLRP P2300SCMCLRP P2600SCMCLRP P3100SCMCLRP P3500SCMCLRP Marking P-8AM P02AM P03AM P-8CM P02CM P03CM P06CM P07CM P09CM P11CM P13CM P15CM P18CM P21CM P23CM P26CM P31CM P35CM VDRM @lDRM=5μA VS @100V/μs IH IS IT VT @IT=2.2 Amps V min V max mA min mA max A max V max pF min pF max 6 15 25 6 15 25 58 65 75 90 120 140 170 180 190 220 275 320 25 32 40 25 32 40 77 88 98 130 160 180 220 240 260 300 350 400 50 50 50 50 50 50 150 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 25 25 15 25 30 25 55 50 45 45 40 35 35 30 30 30 30 25 55 50 35 75 65 45 85 75 70 70 60 55 50 50 50 45 45 40 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). -©Devices are bi-directional (unless otherwise noted). 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 72 Revised: February 22, 2011 Capacitance @1MHz, 2V bias SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Series Surge Ratings IPP 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 ITSM 50/60 Hz di/dt A min A min A min A min A min A min A min A min A min A min A/μs max A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W DO-214AA V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature 14 12 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 2.0 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -40 -20 0 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 73 Revised: February 22, 2011 160 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 74 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Dimensions — DO-214AA Pad Outline Case Temperature Measurement Point B D 0.110 (2.8) C A 0.079 (2.0) H E inch (millimeter) F K Inches Dimensions 0.079 (2.0) Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 G Part Numbering Part Marking P xxx 0 S C MC L RP REEL PACK TYPE P = SIDACtor Pxxxx xxxxx RoHS COMPLIANT MEDIAN VOLTAGE MC Series CONSTRUCTION VARIABLE IPP RATING PACKAGE TYPE Packing Options Package Type S Description Quantity Added Suffix Industry Standard DO-214AA Tape & Reel Pack 2500 N/A EIA-481-D Tape and Reel Specification — DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) Dimensions are in inches (and millimeters). 0.512 (13.0) Arbor Hole Dia. Direction of Feed 0.49 (12.4) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Cover tape 75 Revised: February 22, 2011 Part Marking Code (Refer to Electrical Characteristics Table) Date Code