Low Cost, Low Noise, CMOS, RRO Operational Amplifiers AD8691/AD8692/AD8694 Data Sheet PIN CONFIGURATIONS APPLICATIONS OUT 1 V– 2 V+ 4 –IN TOP VIEW (Not to Scale) +IN 3 Figure 1. 5-Lead TSOT OUT A 1 AD8691 5 V+ 4 –IN V– 2 +IN A 3 Photodiode amplification Battery-powered instrumentation Medical instruments Multipole filters Sensors Portable audio devices 5 AD8691 04991-030 Offset voltage: 400 µV typical Low offset voltage drift: 6 µV/°C maximum (AD8692/AD8694) Very low input bias currents: 1 pA maximum Low noise: 8 nV/√Hz Low distortion: 0.0006% Wide bandwidth: 10 MHz Unity-gain stable Single-supply operation: 2.7 V to 6 V Qualified for automotive applications 04991-031 FEATURES Figure 2. 5-Lead SC70 AD8692 8 V+ –IN A 2 7 OUT B +IN A 3 6 –IN B V– 4 5 +IN B GENERAL DESCRIPTION 04991-134 OUT A 1 TOP VIEW (Not to Scale) Figure 3. 8-Lead SOIC and 8-Lead MSOP OUT A 1 14 OUT D –IN A 2 13 –IN D +IN A 3 AD8694 V+ 4 TOP VIEW (Not to Scale) 12 +IN D 11 V– +IN B 5 –IN B 6 9 –IN C OUT B 7 8 OUT C 10 +IN C 04991-156 The AD8691, AD8692, and AD8694 are low cost, single, dual, and quad rail-to-rail output, single-supply amplifiers featuring low offset and input voltages, low current noise, and wide signal bandwidth. The combination of low offset, low noise, very low input bias currents, and high speed make these amplifiers useful in a wide variety of applications. Filters, integrators, photodiode amplifiers, and high impedance sensors all benefit from this combination of performance features. Audio and other ac applications benefit from the wide bandwidth and low distortion of these devices. Figure 4. 14-Lead SOIC and 14-Lead TSSOP Applications for these amplifiers include power amplifier (PA) controls, laser diode control loops, portable and loop-powered instrumentation, audio amplification for portable devices, and ASIC input and output amplifiers. The small SC70 and TSOT package options for the AD8691 allow it to be placed next to sensors, thereby reducing external noise pickup. The AD8691, AD8692, and AD8694 are specified over the extended industrial temperature range of −40°C to +125°C. The AD8691 single is available in 5-lead SC70 and 5-lead TSOT packages. The AD8692 dual is available in 8-lead MSOP and narrow SOIC surface-mount packages. The AD8694 quad is available in 14-lead TSSOP and narrow 14-lead SOIC packages. See the Ordering Guide section for automotive grades. Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2004–2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD8691/AD8692/AD8694 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Absolute Maximum Ratings ............................................................5 Applications ....................................................................................... 1 Thermal Characteristics ...............................................................5 General Description ......................................................................... 1 ESD Caution...................................................................................5 Pin Configurations ........................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 Outline Dimensions ....................................................................... 11 Specifications..................................................................................... 3 Ordering Guide .......................................................................... 14 Electrical Characteristics ............................................................. 3 Automotive Products ................................................................. 14 REVISION HISTORY 9/13—Rev. E to Rev. F Changes to Figure 3 and Figure 4 ................................................... 1 Delete Figure 4 and Figure 5; Renumbered Sequentially ............ 1 Changes to Ordering Guide .......................................................... 14 8/11—Rev. D to Rev. E Changes to Figure 20 ........................................................................ 8 11/10—Rev. C to Rev. D Changes to Features Section and General Descriptions Section ................................................................................................ 1 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 14 Added Automotive Products Section .......................................... 14 3/05—Rev. A to Rev. B Added AD8694 ................................................................... Universal 1/05—Rev. 0 to Rev. A Added AD8691 ................................................................... Universal Changes to Features ..........................................................................1 Added Figure 1 and Figure 2............................................................1 Changes to Electrical Characteristics .............................................3 Changes to Figure 6 caption.............................................................6 Changes to Figure 9 ...........................................................................6 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 11 10/04—Revision 0: Initial Version 5/07—Rev. B to Rev. C Change to Figure 1 ........................................................................... 1 Changes to Large Signal Voltage Gain Values in Table 1 ............ 3 Change to Phase Margin Symbol in Table 1 ................................. 3 Change to TA Value for Table 2 ....................................................... 4 Changes to Large Signal Voltage Gain Values in Table 2 ............ 4 Change to Phase Margin Symbol in Table 2 ................................. 4 Changes to Table 4 ............................................................................ 5 Changes to Outline Dimensions................................................... 11 Changes to Ordering Guide .......................................................... 12 Rev. F | Page 2 of 16 Data Sheet AD8691/AD8692/AD8694 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VS = 2.7 V, VCM = VS/2, TA = 25°C, unless otherwise noted. Table 1. Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol Test Conditions/Comments VOS VCM = −0.3 V to +1.6 V VCM = −0.1 V to +1.6 V; −40°C < TA < +125°C Min IB Typ Max Unit 0.4 2.0 3.0 1 50 260 0.5 20 75 +1.6 mV mV pA pA pA pA pA pA V dB dB 0.2 −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current IOS 0.1 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain AD8691/AD8692 AD8694 Offset Voltage Drift AD8691 AD8692/AD8694 INPUT CAPACITANCE Common-Mode Input Capacitance Differential Input Capacitance OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Settling Time Gain Bandwidth Product Phase Margin Total Harmonic Distortion + Noise NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density CMRR VCM = −0.3 V to +1.6 V VCM = −0.1 V to +1.6 V; −40°C < TA < +125°C −0.3 68 60 RL = 2 kΩ, VO = 0.5 V to 2.2 V RL = 2 kΩ, VO = 0.5 V to 2.2 V 90 60 90 85 AVO 250 V/mV V/mV ∆VOS/∆T 2 1.3 CCM CDM VOH VOL ISC ZOUT PSRR ISY IL = 1 mA −40°C < TA < +125°C IL = 1 mA −40°C < TA < +125°C 2.64 2.6 pF pF 2.66 V V mV mV mA Ω 95 95 0.85 SR tS GBP Øm THD + N RL = 2 kΩ To 0.01% G = 1, RL = 600 Ω, f = 1 kHz, VO = 250 mV p-p 5 1 10 60 0.003 en p-p en en in f = 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 1.6 8 6.5 0.05 Rev. F | Page 3 of 16 40 60 ±20 12 80 75 µV/°C µV/°C 5 2.5 25 f = 1 MHz, AV = 1 VS = 2.7 V to 5.5 V −40°C < TA < +125°C VO = 0 V −40°C < TA < +125°C 12 6 0.95 1.2 dB dB mA mA V/µs µs MHz Degrees % 3.0 12 µV p-p nV/√Hz nV/√Hz pA/√Hz AD8691/AD8692/AD8694 Data Sheet VS = 5.0 V, VCM = VS/2, TA = 25°C, unless otherwise noted. Table 2. Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol Test Conditions/Comments VOS VCM = −0.3 V to +3.9 V VCM = −0.1 V to +3.9 V; −40°C < TA < +125°C Min IB Typ Max Unit 0.4 2.0 3.0 1 50 260 0.5 20 75 +3.9 mV mV pA pA pA pA pA pA V dB dB 0.2 −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current IOS 0.1 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain AD8691/AD8692 AD8694 Offset Voltage Drift AD8691 AD8692/AD8694 INPUT CAPACITANCE Common-Mode Input Capacitance Differential Input Capacitance OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low AD8691/AD8692 AD8694 AD8691/AD8692 AD8694 Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Settling Time Full Power Bandwidth Gain Bandwidth Product Phase Margin Total Harmonic Distortion + Noise NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density CMRR VCM = −0.3 V to +3.9 V VCM = −0.1 V to +3.9 V; −40°C < TA < +125°C −0.3 70 67 VO = 0.5 V to 4.5 V, RL = 2 kΩ, VCM = 0 V VO = 0.5 V to 4.5 V, RL = 2 kΩ, VCM = 0 V 250 150 95 95 AVO 2000 V/mV V/mV ∆VOS/∆T 2 1.3 CCM CDM VOH VOL ISC ZOUT PSRR ISY IL = 1 mA IL = 10 mA −40°C to +125°C IL = 1 mA IL = 10 mA IL = 10 mA −40°C to +125°C −40°C to +125°C 4.96 4.7 4.6 pF pF 4.98 4.78 V V V mV mV mV mV mV mA Ω 95 95 0.95 SR tS BWP GBP Øm THD + N RL = 2 kΩ To 0.01% <1% distortion G = 1, RL = 600 Ω, f = 1 kHz, VO = 1 V p-p 5 1 360 10 65 0.0006 en p-p en en in f = 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 1.6 8 6.5 0.05 Rev. F | Page 4 of 16 40 210 240 290 370 ±80 10 80 75 µV/°C µV/°C 5 2.5 20 165 185 f = 1 MHz, AV = 1 VS = 2.7 V to 5.5 V −40°C < TA < +125°C VO = 0 V −40°C < TA < +125°C 12 6 1.05 1.3 dB dB mA mA V/µs µs kHz MHz Degrees % 3.0 12 µV p-p nV/√Hz nV/√Hz pA/√Hz Data Sheet AD8691/AD8692/AD8694 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. THERMAL CHARACTERISTICS Table 3. θJA is specified for the worst-case conditions, that is, the device soldered in the circuit board for surface-mount packages. Parameter Supply Voltage Input Voltage Differential Input Voltage Output Short-Circuit Duration to GND Storage Temperature Range Operating Temperature Range Junction Temperature Range Lead Temperature (Soldering, 60 sec) Rating 6V VSS − 0.3 V to VDD + 0.3 V ±6 V Observe derating curves Table 4. Thermal Resistance Package Type 8-Lead MSOP (RM-8) 8-Lead SOIC (R-8) 5-Lead TSOT (UJ-5) 5-Lead SC70 (KS-5) 14-Lead TSSOP (RU-14) 14-Lead SOIC (R-14) −65°C to +150°C −40°C to +125°C −65°C to +150°C 300°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. F | Page 5 of 16 θJA 210 158 207 376 180 120 θJC 45 43 61 126 35 36 Unit °C/W °C/W °C/W °C/W °C/W °C/W AD8691/AD8692/AD8694 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VS = +5 V or ±2.5 V, unless otherwise noted. 300 2500 VS = 5V AND 2.7V VS = 5V VCM = –0.3V TO +3.9V 250 200 1500 IB (pA) NUMBER OF AMPLIFIERS 2000 1000 150 100 50 500 0 –1.0 –0.5 0 0.5 1.0 1.5 2.0 VOS (mV) –50 –40 –30 –20 –10 20 30 40 50 70 60 80 90 100 110 120 Figure 8. Input Bias Current vs. Temperature 1.0 30 VS = 5V AND 2.7V VCM = 2.5V TA = –40°C TO +125°C 0.8 SUPPLY CURRENT (mA) 25 20 15 10 0.6 0.4 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 TCVOS (µV/°C) 0 04991-004 0 0 2 3 4 5 6 7 VS (V) Figure 6. AD8692/AD8694 Input Offset Voltage Drift Distribution Figure 9. Supply Current vs. Supply Voltage 2.5 2000 1600 1 04991-007 0.2 5 VS = ±2.5V AND ±1.35V VS = 5V TA = 25°C ISY @ ±2.5V 2.0 SUPPLY CURRENT (mA) 1200 800 400 0 –400 –800 ISY @ ±1.35V 1.5 1.0 0.5 –1200 –2000 –0.3 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 COMMON-MODE VOLTAGE (V) 04991-005 –1600 Figure 7. Input Offset Voltage vs. Common-Mode Voltage 0 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 10. Supply Current vs. Temperature Rev. F | Page 6 of 16 140 04991-008 NUMBER OF AMPLIFIERS 10 TEMPERATURE (°C) Figure 5. Input Offset Voltage Distribution INPUT OFFSET VOLTAGE (µV) 0 04991-006 –1.5 04991-003 0 –2.0 Data Sheet AD8691/AD8692/AD8694 100 VS = ±2.5V, ±1.35V RL = 2kΩ CL = 15pF VS = 5V 80 100 AD8691_92 SINK 10 AD8694 SINK 60 40 90 20 45 0 0 AD8691_92 SOURCE 1 0.1 1 10 100 LOAD CURRENT (mA) –90 –40 1k 1M 10M Figure 14. Open-Loop Gain and Phase vs. Frequency 35 120 VS = 5V VS = 5V AND 2.7V AD8691_92 (V DD – VOH) 30 100 AD8694 (V DD – VOH) 80 CMRR (dB) 20 AD8691_92 (V OL) 15 AD8694 (V OL) 60 40 10 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 0 04991-010 0 –40 1k 10k Figure 12. Output Voltage Swing vs. Temperature (IL = 1 mA) 10M 120 VS = 5V VS = 5V AND 2.7V AD8691_92 (V DD – VOH) 300 100 AD8694 (V DD – VOH) PSRR (dB) 80 200 AD8691_92 (V OL) 150 AD8694 (V OL) 100 60 40 20 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 04991-011 50 0 –40 1M Figure 15. CMRR vs. Frequency 350 250 100k FREQUENCY (Hz) 04991-013 20 5 Figure 13. Output Voltage Swing vs. Temperature (IL = 10 mA) 0 10 100 1k 10k 100k FREQUENCY (Hz) Figure 16. PSRR vs. Frequency Rev. F | Page 7 of 16 1M 10M 04991-014 OUTPUT VOLTAGE SWING (mV) 100k FREQUENCY (Hz) Figure 11. Output Voltage to Supply Rail vs. Load Current 25 10k 04991-012 0.01 –45 –20 AD8694 SOURCE 0.1 0.001 OUTPUT VOLTAGE SWING (mV) PHASE (Degrees) OPEN-LOOP GAIN (dB) 1000 04991-009 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) 10000 AD8691/AD8692/AD8694 Data Sheet 10000 VS = 5V CL = 200pF RL = ∞ AV = 1 VS = ±2.5V 1000 IMPEDANCE (Ω) 10 VOLTAGE (1V/DIV) AV = 100 100 AV = 10 1 AV = 1 0.1 0.01 1k 10k 100k 1M 10M FREQUENCY (Hz) 04991-018 0.0001 100 04991-015 0.001 TIME (400ns/DIV) Figure 20. Large Signal Transient Response Figure 17. Closed-Loop Output Impedance vs. Frequency 40 VS = 5V AND 2.7V RL = ∞ AV = –1 35 VS = ±2.5V AV = –50 VOUT (V) 25 20 0 –2.5 100 15 VIN (mV) 10 1 10 100 1k LOAD CAPACITANCE (pF) 04991-016 0 04991-019 0 5 TIME (400ns/DIV) Figure 18. Small Signal Overshoot vs. Load Capacitance Figure 21. Positive Overload Recovery VS = ±2.5V, ±1.35V RL = 10kΩ CL = 200pF AV = 1 VOLTAGE (50mV/DIV) VOUT (V) VS = ±2.5V AV = –50 2.5 0 VIN (mV) 0 TIME (200ns/DIV) 04991-017 –100 TIME (400ns/DIV) Figure 22. Negative Overload Recovery Figure 19. Small Signal Transient Response Rev. F | Page 8 of 16 04991-020 OVERSHOOT (%) 30 Data Sheet AD8691/AD8692/AD8694 1000 0.1 VS = ±2.5V AND ±1.35V VS = ±2.5V AV = 1 VIN = 1V p-p BW = 20kHz NOISE (nV/ Hz) THD + N (%) 0.01 RL = 600Ω RL = 1kΩ 0.001 100 10 1k 10k FREQUENCY (Hz) 20k 1 04991-021 100 1 10 100 10000 1000 FREQUENCY (Hz) Figure 23. THD + N vs. Frequency 04991-023 RL = 100kΩ 0.0001 20 Figure 25. Voltage Noise Density 150 +2.5V VS = 5V AND 2.7V CHANNEL SEPARATION (dB) 140 VOLTAGE NOISE (1µV/DIV) R1 10kΩ V+ A VIN 28mV p-p V– V– 130 –2.5V VOUT R2 100Ω B V+ 120 110 100 Figure 24. 0.1 Hz to 10 Hz Input Voltage Noise 80 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 26. AD8692/AD8694 Channel Separation Rev. F | Page 9 of 16 04991-024 TIME (1s/DIV) 04991-022 90 AD8691/AD8692/AD8694 Data Sheet VS = +2.7 V or ±1.35 V, unless otherwise noted. 60 1200 VS = 2.7V VCM = –0.3V TO +1.6V VS = 2.7V AD8691_92 (V DD – VOH) 800 600 400 0 –2.0 –1.5 –1.0 0 –0.5 0.5 1.0 2.0 1.5 VOS (mV) AD8694 (V DD – VOH) 40 30 AD8691_92 (V OL) 20 AD8694 (V OL) 10 0 –40 04991-025 200 50 –20 0 20 40 60 2000 120 VS = 2.7V CL = 200pF RL = ∞ AV = 1 VS = 2.7V TA = 25°C 1200 VOLTAGE (500mV/DIV) INPUT OFFSET VOLTAGE (µV) 100 Figure 30. Output Voltage Swing vs. Temperature (IL = 1 mA) Figure 27. Input Offset Voltage Distribution 1600 80 TEMPERATURE (°C) 04991-028 OUTPUT VOLTAGE SWING (mV) NUMBER OF AMPLIFIERS 1000 800 400 0 –400 –800 –1200 0 0.3 0.6 0.9 1.2 1.5 1.6 COMMON-MODE VOLTAGE (V) Figure 31. Large Signal Transient Response Figure 28. Input Offset Voltage vs. Common-Mode Voltage VS = 2.7V 1k 100 AD8691_92 SINK AD8694 SINK AD8691_92 SOURCE 1 AD8694 SOURCE 0.1 0.001 0.01 0.1 1 10 LOAD CURRENT (mA) 04991-027 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) 10k 10 TIME (400ns/DIV) Figure 29. Output Voltage to Supply Rail vs. Load Current Rev. F | Page 10 of 16 04991-029 –2000 –0.3 04991-026 –1600 Data Sheet AD8691/AD8692/AD8694 OUTLINE DIMENSIONS 3.20 3.00 2.80 5.15 4.90 4.65 5 8 3.20 3.00 2.80 1 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15° MAX 1.10 MAX 0.80 0.55 0.40 0.23 0.09 6° 0° 0.40 0.25 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 32. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 5.00 (0.1968) 4.80 (0.1890) 1 5 6.20 (0.2441) 5.80 (0.2284) 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY 0.10 SEATING PLANE 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0196) 0.25 (0.0099) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 33. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) Rev. F | Page 11 of 16 012407-A 8 4.00 (0.1574) 3.80 (0.1497) AD8691/AD8692/AD8694 Data Sheet 2.20 2.00 1.80 1.35 1.25 1.15 5 1 2.40 2.10 1.80 4 3 2 0.65 BSC 0.40 0.10 1.10 0.80 0.10 MAX COPLANARITY 0.10 0.46 0.36 0.26 0.22 0.08 SEATING PLANE 0.30 0.15 072809-A 1.00 0.90 0.70 COMPLIANT TO JEDEC STANDARDS MO-203-AA Figure 34. 5-Lead Thin Shrink Small Outline Package [SC70] (KS-5) Dimensions shown in millimeters 2.90 BSC 4 5 2.80 BSC 1.60 BSC 1 2 3 0.95 BSC 1.90 BSC *1.00 MAX 0.10 MAX 0.50 0.30 0.20 0.08 SEATING PLANE 8° 4° 0° 0.60 0.45 0.30 *COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS. Figure 35. 5-Lead Thin Small Outline Transistor Package [TSOT] (UJ-5) Dimensions shown in millimeters Rev. F | Page 12 of 16 100708-A *0.90 MAX 0.70 MIN Data Sheet AD8691/AD8692/AD8694 5.10 5.00 4.90 14 8 4.50 4.40 4.30 6.40 BSC 1 7 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.20 0.09 0.30 0.19 0.75 0.60 0.45 8° 0° SEATING PLANE 061908-A 1.05 1.00 0.80 COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 36. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters 8.75 (0.3445) 8.55 (0.3366) 8 14 1 7 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 0.51 (0.0201) 0.31 (0.0122) 6.20 (0.2441) 5.80 (0.2283) 0.50 (0.0197) 0.25 (0.0098) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 37. 14-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches) Rev. F | Page 13 of 16 060606-A 4.00 (0.1575) 3.80 (0.1496) AD8691/AD8692/AD8694 Data Sheet ORDERING GUIDE Model 1, 2 AD8691AUJZ-R2 AD8691AUJZ-REEL AD8691AUJZ-REEL7 AD8691AKSZ-R2 AD8691AKSZ-REEL AD8691AKSZ-REEL7 AD8691WAUJZ-R7 AD8691WAUJZ-RL AD8692ARMZ-R7 AD8692ARMZ-REEL AD8692ARZ AD8692ARZ-REEL AD8692ARZ-REEL7 AD8692WARMZ-REEL AD8694ARUZ AD8694ARUZ-REEL AD8694WARUZ AD8694WARUZ-REEL AD8694ARZ AD8694ARZ-REEL AD8694ARZ-REEL7 AD8694WAC-P3 AD8694WAC-P7 1 2 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 5-Lead TSOT 5-Lead TSOT 5-Lead TSOT 5-Lead SC70 5-Lead SC70 5-Lead SC70 5-Lead TSOT 5-Lead TSOT 8-Lead MSOP 8-Lead MSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead MSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead TSSOP 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N Die Die Package Option UJ-5 UJ-5 UJ-5 KS-5 KS-5 KS-5 UJ-5 UJ-5 RM-8 RM-8 R-8 R-8 R-8 RM-8 RU-14 RU-14 RU-14 RU-14 R-14 R-14 R-14 Branding ACA ACA ACA ACA ACA ACA ACA ACA APA APA APA Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD8691W/AD8692W/AD8694W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. F | Page 14 of 16 Data Sheet AD8691/AD8692/AD8694 NOTES Rev. F | Page 15 of 16 AD8691/AD8692/AD8694 NOTES ©2004–2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04991-0-9/13(F) Rev. F | Page 16 of 16