Chemical-resistant Proximity Sensor E2FQ CSM_E2FQ_DS_E_5_1 Inductive Profoximity Sensor with Chemical-resistant Fluororesin Case • Housing and mounting are made of Fluororesin resistant to chemicals. • Maximum sensing distance: 10 mm. Be sure to read Safety Precautions on page 5. Note: The cable is made of vinyl chloride and requires separate protection. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Ordering Information Sensors [Refer to Dimensions on page 6.] Appearance M12 Shielded M18 M30 Sensing distance 2 mm 5 mm 10 mm Output configuration Operation mode DC 2-wire DC 3-wire, NPN DC 2-wire DC 3-wire, NPN NO AC 2-wire DC 2-wire DC 3-wire, NPN AC 2-wire Model E2FQ-X2D1 2M E2FQ-X2E1 2M E2FQ-X5D1 2M E2FQ-X5E1 2M E2FQ-X5Y1 2M E2FQ-X10D1 2M E2FQ-X10E1 2M E2FQ-X10Y1 2M 1 E2FQ Ratings and Specifications Model E2FQ-X2E1 E2FQ-X2D1 Item E2FQ-X5E1 E2FQ-X5D1, E2FQ-X5Y1 E2FQ-X10E1 E2FQ-X10D1, E2FQ-X10Y1 Sensing distance 2 mm ±10% 5 mm ±10% 10 mm ±10% Set distance 0 to 1.6 mm 0 to 4 mm 0 to 8 mm Differential travel E1/Y1 Models: 10% max. of sensing distance, D1 Models: 20% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 3.) Standard sensing object Iron, 12 × 12 × 1 mm Iron, 18 × 18 × 1 mm Iron, 30 × 30 × 1 mm E1 Models: 600 Hz D1 Models: 500 Hz E1 Models: 400 Hz D1 Models: 300 Hz Response frequency * E1 Models: 1.5 kHz D1 Models: 800 Hz Power supply voltage (operating voltage range) E1 Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. Y1 Models: 24 to 240 VAC (20 to 264 VAC), 50/60 Hz D1 Models: 12 to 24 VDC (10 to 36 VDC), ripple (p-p): 20% max. Current consumption E1 Models: 17 mA max. Leakage current D1 Models: 0.8 mA max., Y1 Models: 1.7 mA max. (at 200 VAC) Control output Y1 Models: 25 Hz Load current E1 Models: 200 mA max., D1 Models: 5 to 100 mA, Y1 Models: 5 to 300 mA Residual voltage E1 Models: 2 V max. (Load current: 200 mA, Cable length: 2 m) Y1 Models: Refer to Engineering Data on page 3. D1 Models: 3 V max. (Load current: 100 mA, Cable length: 2 m) Indicators E Models: Detection indicator (red), Y Models: Operation indicator (red), D Models: Operation indicator (red), Setting indicator (green) (NO only) Operation mode (with sensing object approaching) E1/D1/Y1 Models: NO (Refer to the timing charts under I/O Circuit Diagrams on page 5 for details.) Protection circuits E1 Models: Load short-circuit protection, Reverse polarity protection, Surge suppressor, D1/Y1 Models: Surge suppressor Ambient temperature range Operating/Storage: −25 to 70°C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C Voltage influence E1 Models: ±2.5% max. of sensing distance at rated voltage in the rated voltage ±15% range D1 Models: ±2.5% max. of sensing distance at rated voltage in the rated voltage ±20% range Y1 Models: ±1% max. of sensing distance at rated voltage in the rated voltage ±10% range Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength E1/D1 Models: 1,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case Y Models: 4,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 10 times each in X, Y, and Z directions Degree of protection IEC 60529 IP67, in-house standards: oil-resistant Connection method Pre-wired Models (Cable length: 2 m) Weight (packed state) Approx. 70 g Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Approx. 130 g Approx. 170 g Case Sensing surface Materials Fluororesin Clamping nuts Toothed washer Zinc-plated iron Cable Vinyl chloride Accessories Instruction manual * The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. 2 E2FQ Engineering Data (Reference Value) Sensing Area Distance X (mm) E2FQ-X@ E2FQ-X10 10 Y 8 X 6 E2FQ-X5 4 E2FQ-X2 2 -20 -16 -12 -8 -4 0 4 8 E2FQ-X2 Sensing Head 12 16 Distance Y (mm) E2FQ-X5 Sensing Head E2FQ-X10 Sensing Head Influence of Sensing Object Size and Material 2.4 d× d 2.2 t = 1 mm Iron X 2 1.8 Stainless steel (SUS304) 1.6 1.4 E2FQ-X10@ 7 d× d t = 1 mm X 6 Iron 5 Stainless steel (SUS304) 4 1.2 Distance X (mm) E2FQ-X5@ Distance X (mm) Distance X (mm) E2FQ-X2@ 12 11 d× d 3 1 8 7 Stainless steel (SUS304) 5 Brass Brass 2 0.6 Aluminum Aluminum 0.4 Iron 9 6 0.8 t = 1 mm X 10 Brass 4 3 Aluminum 2 1 1 0.2 0 5 10 15 20 25 Side length of sensing object: d (mm) 0 5 10 15 20 25 30 35 40 50 Side length of sensing object: d (mm) 0 10 20 30 40 50 60 Side length of sensing object: d (mm) Residual Output Voltage E2FQ-X@Y1 at 24 VAC 5 Load voltage VL (V) Residual output voltage (V) E2FQ-X@ 4 30 24 VAC 20 Residual output voltage ON 3 V ~ 2 10 VL ~ 1 0 24 VAC A Residual Load Voltage 1 3 5 10 30 50 100 300 500 1,000 Load current (mA) 01 3 OFF 5 10 30 50 100 300 500 1,000 Load current (mA) 3 E2FQ 120 E2FQ-X@Y1 at 200 VAC Residual output voltage Load voltage VL (V) Load voltage VL (V) E2FQ-X@Y1 at 100 VAC ON 100 80 ~ 30 50 VL 200 VAC A ~ 80 40 Residual load voltage 01 3 OFF 10 V ~ 100 VAC ~A 20 Residual load voltage 01 3 5 ON 200 120 VL 40 Residual output voltage 160 V 60 240 100 300 Load current (mA) OFF 5 10 30 50 100 300 Load current (mA) Leakage Current E2FQ-X@Y Leakage current (mA) Leakage current (mA) E2FQ-X@D 1.0 0.8 0.6 2.0 Protective resistance mA ~ V ~ 1.5 Proximity Sensor (OFF) AC power, 50/60Hz 0.4 1.0 0.2 0 10 20 30 40 Power supply voltage (V) 0 50 100 150 200 250 Power supply voltage (V) 4 E2FQ I/O Circuit Diagrams Operation Output conmode figuration Model Timing chart Output circuit Brown Sensing object Not present Load Operate E2FQ-X2E1 E2FQ-X5E1 E2FQ-X10E1 NPN (between brown and black leads) Load Proximity Sensor main circuit Reset H Output voltage (between black and blue leads) Unstable 4.7 kΩ Black 2.2 Ω *2 Output E2FQ-X2D1 E2FQ-X5D1 E2FQ-X10D1 (%) 0V *1. 200 mA max. (load current). *2. When a transistor is connected. Set position Stable sensing area Brown Proximity Sensor DC 2-wire Tr Blue 100 80 Rated sensing distance Load +V Sensing object NO *1 L ON Detection indicator (red) OFF Non-sensing sensing area area +V 100 Ω Present Proximity Sensor main circuit 0 ON OFF Setting indicator (green) Blue 0V ON Operation indicator OFF (red) ON Note: The load can be connected to either the +V or 0 V side. Control output OFF Brown Sensing object Present AC 2-wire E2FQ-X5Y1 E2FQ-X10Y1 Operate Load Reset Operation indicator (red) Load Proximity Sensor main circuit Not present Blue ON OFF Safety Precautions Refer to Warranty and Limitations of Liability. WARNING Mutual Interference This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. When installing two or more Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. Mutual Interference (Unit: mm) Precautions for Correct Use Do not use this product under ambient conditions that exceed the ratings. ● Design Influence of Surrounding Metal When mounting the Sensor within a metal panel, ensure that the clearances given in the following table are maintained. Failure to maintain these distances may cause deterioration in the performance of the Sensor. Model Item E2FQ-X2@ E2FQ-X5@ E2FQ-X10@ A 30 50 100 B 20 35 70 A B Mounting Do not tighten the nut with excessive force. A washer must be used with the nut. l n m d dia. D l m Influence of Surrounding Metal Model E2FQ-X2@ E2FQ-X5@ E2FQ-X10@ Item l 0 d 12 18 30 (Unit: mm) D 0 m 8 20 40 n 18 27 45 Note: The following torque assume washers are being used. Model E2FQ-X2@ E2FQ-X5@ E2FQ-X10@ Torque 0.98 N·m 2 N·m Miscellaneous Chemical Resistance Refer to Chemical Resistance for details. 5 E2FQ (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. E2FQ-X2D1 E2FQ-X2E1 38 21 dia. 38 21 dia. 27 24 17 27 24 17 * Detection indicator (red) Two clamping nuts M12 × 1 M12 × 1 6 Two toothed washers * 6-dia. vinyl-insulated round cable with 3 conductors (Flame resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). * Operation indicator (red) Two clamping nuts 6 Two toothed washers * 6-dia. vinyl-insulated round cable with 2 conductors (Flame resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). E2FQ-X5D1 E2FQ-X5Y1 E2FQ-X5E1 47 47 40 32 29 29 dia. 24 40 32 29 29 dia. 24 *1 * Indicator *2 M18 × 1 Detection indicator (red) M18 × 1 8 Two clamping nuts 8 Two clamping nuts Two toothed washers *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flameresistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. D1: Operation indicator (red) and Setting indicator (green) Y1: Operation indicator (red) Two toothed washers * 6-dia. vinyl-insulated round cable with 3 conductors (Flame resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). E2FQ-X10D1 E2FQ-X10Y1 E2FQ-X10E1 57 57 42 dia. 50 42 dia. 41 36 50 41 36 38 38 *1 * Indicator *2 Detection indicator (red) M30 × 1.5 Two clamping nuts 8 Two toothed washers * 6-dia. vinyl-insulated round cable with 3 conductors (Flame resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). M30 × 1.5 8 Two clamping nuts Two toothed washers *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. D1: Operation indicator (red) and Setting indicator (green) Y1: Operation indicator (red) Mounting Hole Dimensions Model F F (mm) E2FQ-X2@ 12.5 +0.5 0 dia. E2FQ-X5@ 18.5 +0.5 0 dia. E2FQ-X10@ 30.5 +0.5 0 dia. 6 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2014.10 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2014 All Right Reserved.