Accessories Y92@ CSM_Y92__DS_E_5_4 Mounting Brackets Special resin mounting sleeves: Four different models available. Simply select the size that fits the outside diameter of the Sensor. Mounting Bracket Dimensions A Item Dimension (mm) B Model E G F D C Y92E-B8 Y92E-B12 Y92E-B18 Y92E-B30 A B C D E 18±0.2 24±0.2 32±0.2 45±0.2 10 max. 12.5 max. 17 max. 17 max. 18 20 30 50 8 dia. 12 dia. 18 dia. 30 dia. 28 max. 37 max. 47 max. 60 max. F 6 6 7 10 Applied Applicable hexagonal Sensor G bolts diameter 7.4 dia. M4 × 20 M8 8 dia. M4 × 25 M12 9.8 dia. M5 × 32 M18 9.8 dia. M5 × 50 M30 Note: Consider the influence of surrounding metal when mounting non-shielded Sensors. (Refer to information on individual Sensors for dimensions.) Material: Mounting Bracket: Polyacetal Hexagonal bolt and spring washer: Nickel-plated iron Mounting Sleeves (Quick Mounting) Once the Mounting Sleeve and Sensor have been set properly, readjustment is not required when replacing the Sensor. Mounting Sleeve Dimensions Item Dimension (mm) A B C D Model A F E Material: Bracket: Nickel-plated iron Nut: Nickel-plated brass Mounting Sleeve: Polyacetal F Y92E-G8 Approx. 28 18.5 15.5 M12 × 1 17 4 Y92E-G12 Approx. 29 20.5 17.5 M18 × 1 24 4 Y92E-G18 Approx. 35 23.5 20.5 M24 × 1.5 30 5 Y92E-G30 Approx. 39 27.5 24.5 M36 × 1.5 41 5 B C D Two Mounting Sleeve clamping nuts E (between opposing faces) E (between opposing faces) E (between opposing faces) Distance across Sensor lock nut: E Applicable Sensors E2E/E2E2 M8 Shielded Sensors E2E/E2E2 M12 Shielded Sensors E2E/E2E2 M18 Shielded Sensors E2E/E2E2 M30 Shielded Sensors Note: Do not tighten the nut with excessive force. Do not exceed the torque in the following table. Item Mounting Sleeve clamping nuts Model Y92E-G8 18 N·m Y92E-G12 40 N·m Y92E-G18 70 N·m Y92E-G30 100 N·m Sensor lock nut 6 N·m 15 N·m 15 N·m 30 N·m 1 Y92@ Protective Covers [A Protective Cover cannot be used with a Capactive Proximity Sensor.] Covers are available to protect the Sensing Head. Simply select the size that fits the outside diameter of the Sensor. Protective Cover Dimensions Item Model Y92E-E12 Dimension (mm) A B 14 dia. 5 C +0.2 0.5 −0.1 Cover inner diameter (threaded) Material M12 × 1 M12 M18 × 1 M18 Shielded Models Y92E-E18 21 dia. 6 1±0.2 Y92E-E30 33 dia. 8 1.5±0.2 Y92E-E12M 14 dia. 12 0.5 −0.1 +0.2 M12 × 1 M30 Shielded Models Polyacetal resin M12 Unshielded Models Y92E-E18M 21 dia. 16 1±0.2 M18 × 1 M18 Unshielded Models Y92E-E30M 33 dia. 21 1.5±0.2 M30 × 1.5 M30 Unshielded Models Shielded Models M30 × 1.5 B C Applicable Sensor diameter A Sputter Protective Covers (Threaded on Inside of Cover) [A Sputter Protective Covers cannot be used with a Capactive Proximity Sensor.] The cover uses Fluororesin, so that chips that adhere due to sputtering can be easily removed. Sputter Protective Cover Dimensions D Item C Model A Y92E-E8-7 B A 10 dia. Dimension (mm) B C +0.2 D Applicable Sensor diameter M8 × 1 0.5 −0.1 5 M8 Shielded Models 5 M12 Shielded Models 6 8 M18 Shielded Models M30 Shielded Models Y92E-E12-7 14 dia. M12 × 1 +0.2 0.5 −0.1 Y92E-E18-7 Y92E-E30-7 21 dia. 33 dia. M18 × 1 M30 × 1.5 1±0.2 1.5±0.2 Note: Do not screw on too tightly, or the cap may be damaged. Sputter Protective Covers (Not Threaded on Inside of Cover) [A Sputter Protective Covers cannot be used with a Capactive Proximity Sensor.] Chips that adhere due to sputtering can be easily removed. Sputter Protective Cover Dimensions Item Model 1-dia. through hole Dimension (mm) A B C D Y92E-E12-2 11.0 dia. 14.0 dia. 5.0 1.0 Y92E-E18-2 17.0 dia. 7.0 3.0 Y92E-E30-2 28.5 dia. 33.0 dia. 8.0 6.0 21 dia. C0.5 A * C0.5 C0.5 D B Material Applicable Sensor diameter M12 Shielded Models Silicon rubber M18 Shielded Models M30 Shielded Models * There is no protrusion on Y92E-E12-2. C 2 Y92@ Protective Cover (Metal Cover for E2V and E2EZ Sensors) Protect the Sensor from horizontal shocks and prevent the sensing surface from hitting workpieces. The countermeasure for aluminum chips functions even with the Cover attached. Protective Cover Dimensions Model Item Dimension (mm) A B (threading) C D Y92E-VM12 13 dia. M12 × 1 0.60±0.05 5 Y92E-VM18 19 dia. M18 × 1 0.60±0.05 6 Y92E-VM30 31 dia. M30 × 1.5 0.60±0.05 8 D C E Applicable Sensor E2V, M12 with shield E2EZ-X2D@-N E2EZ-X2D1-M1(T)(G)J E2V M18 with shield 14 dia. E2EZ-X4D@-N E2EZ-X4D1-M1(T)(G)J E2V M30 with shield 24 dia. E2EZ-X8D@-N E2EZ-X8D1-M1(T)(G)J Material 9 dia. SUS303 B E A Ratings and Performances with the Protective Cover Mounted Item Model E2V-X@ E2EZ-X@ Sensing distance When the Cover is mounted, the range changes by ±10% in comparison with the range without the Cover mounted. Use the Sensor within the set distance range. When the Cover is mounted, the range changes by ±10% in comparison with the range without the Cover mounted. For M30 models, the range changes by ±15%. Use the Sensor within the set distance range. Ambient temperature range Operating: 5 to 55°C (with no condensation.) Storage: -25 to 70°C (with no icing or condensation.) Operating: 0 to 50°C (with no icing or condensation.) Storage: 0 to 50°C (with no icing or condensation.) Note: Other ratings and performances do not change from those of the E2V/E2EZ. You can use a thread-locking compound to mount the Cover more securely. Nut Sets These nut sets are for mounting the Sensors. Order them if you loose the mounting screws. Order the correct set for the outer diameter of your Sensor. Model Item Applicable Sensor Y92E-NWM08-E2E Y92E-NWM12-E2E Y92E-NWM18-E2E Applicable Sensor diameter E2E M12 M18 Y92E-NWM30-E2E M30 Y92E-NWM12-E2EQ M12 Y92E-NWM18-E2EQ E2EQ Y92E-NWM30-E2EQ M30 M8 Y92E-NWM12 M12 E2FM Y92E-NWM30 M18 M12 E2EH M18 Y92E-NWM30-E2EH M30 Y92E-NWM12-E2EZ M12 Y92E-NWM18-E2EZ E2EZ M18 Y92E-NWM30-E2EZ M30 Y92E-NWM08-E2F M8 Y92E-NWM12-E2F Y92E-NWM18-E2F Y92E-NWM30-E2F Clamping nuts (SUS303): 2 Toothed washer (iron with zinc plating): 1 M30 Y92E-NWM12-E2EH Y92E-NWM18-E2EH Clamping nuts (bronze with nickel plating): 2 Toothed washer (iron with zinc plating): 1 M18 Y92E-NWM8 Y92E-NWM18 Set contents M8 E2F M12 M18 Clamping nuts (SUS316L): 2 Clamping nuts (iron with zinc plating): 2 Toothed washer (iron with zinc plating): 1 Clamping nuts (polyacetal): 2 M30 3 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2016.5 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2016 All Right Reserved.