Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC1040LP3CE v00.0112 Amplifiers - Low Noise - SMT GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz Typical Applications Features This HMC1040LP3BE is ideal for: Low Noise Figure: 2.2 dB • Point-to-Point Radios High Gain: 23 dB • Test Instrumentation P1dB Output Power: +12 dBm • SatCom Transponders & VSAT Single Supply: +2.5V @ 70 mA • Industrial Sensors Output IP3: +22 dBm • EW & ECM Subsystems 50 Ohm Matched Input/Output 16 Lead 3x3 mm SMT Package: 16mm² General Description Functional Diagram The HMC1040LP3CE is a self-biased GaAs MMIC Low Noise Amplifier housed in a leadless 3x3 mm plastic surface mount package. The amplifier operates between 24 and 43.5 GHz, delivering 23 dB of small signal gain, 2.2 dB noise figure, and output IP3 of +22 dBm, while requiring only 70 mA from a +2.5 V supply. The P1dB output power of +12 dBm enables the LNA to function as a LO driver for many of Hittite’s balanced, I/Q and image reject mixers. The HMC1040LP3CE features I/Os that are DC blocked and internally matched to 50 Ohms, and is ideal for high capacity microwave radios and VSAT applications. Electrical Specifications, TA = +25° C, Vdd1 = Vdd2 = Vdd3 = +2.5V, Idd = 70 mA Parameter Min. Frequency Range Gain [1] Gain Variation over Temperature Noise Figure [1] Typ. Max. Min. 24 - 27.5 22 25 20 0.022 2.7 Typ. Max. Min. 27.5 - 33.5 23 17 0.021 3.2 2.2 Typ. Max. 33.5 - 43.5 2.7 Units GHz 20 dB 0.021 dB /°C 2.7 3.2 dB Input Return Loss 11 12 10 dB Output Return Loss 16 13 10 dB Output Power for 1 dB Compression 12 12 12 dBm Saturated Output Power (Psat) 14 14 14 dBm Output Third Order Intercept (IP3) 22 22 24 dBm Supply Current (Idd) (Vdd = 2.5V) 70 85 70 85 70 85 mA [1] Board loss subtracted out. 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1040LP3CE v00.0112 GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz Gain vs. Temperature [1] Broadband Gain & Return Loss [1] 26 15 S21 S11 S22 5 GAIN (dB) RESPONSE (dB) 25 -5 22 18 -15 +25C +85C -40C 14 -25 10 -35 15 19 23 27 31 35 39 43 18 47 21 24 Input Return Loss vs. Temperature 33 36 39 42 45 0 -4 -4 +25C +85C -40C RETURN LOSS (dB) RETURN LOSS (dB) 30 Output Return Loss vs. Temperature 0 -8 -12 -16 +25C +85C -40C -8 -12 -16 -20 -20 18 21 24 27 30 33 36 39 42 45 18 21 24 FREQUENCY (GHz) 27 30 33 36 39 42 45 40 43 46 FREQUENCY (GHz) Output IP3 vs. Temperature Noise Figure vs. Temperature [1] 30 6 +25C +85C -40C 5 25 4 IP3 (dBm) NOISE FIGURE (dB) 27 FREQUENCY (GHz) FREQUENCY (GHz) Amplifiers - Low Noise - SMT 30 35 3 20 +25C +85C -40C 15 2 10 1 0 5 20 22 24 26 28 30 32 34 36 38 40 FREQUENCY (GHz) 42 44 46 19 22 25 28 31 34 37 FREQUENCY (GHz) [1] Board loss subtracted out, gain only. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC1040LP3CE v00.0112 GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz Psat vs. Temperature P1dB vs. Temperature 17 15 13 Psat (dBm) P1dB (dBm) 15 11 +25C +85C -40C 9 13 +25C +85C -40C 11 9 7 5 7 19 22 25 28 31 34 37 40 43 19 46 22 25 Reverse Isolation vs. Temperature 34 37 40 43 46 -6 -5 Power Compression @ 25 GHz 30 Pout (dBm), GAIN (dB), PAE (%) 0 -10 -20 +25C +85C -40C -30 -40 -50 -70 18 21 24 27 30 33 36 39 42 25 20 15 10 5 0 -15 45 Pout Gain PAE -14 -13 FREQUENCY (GHz) -12 -11 -10 -9 -8 -7 INPUT POWER (dBm) Power Compression @ 33 GHz Power Compression @ 42 GHz 30 30 Pout Gain PAE 25 Pout (dBm), GAIN (dB), PAE (%) Pout (dBm), GAIN (dB), PAE (%) 31 FREQUENCY (GHz) -60 20 15 10 5 0 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 INPUT POWER (dBm) 3 28 FREQUENCY (GHz) ISOLATION (dB) Amplifiers - Low Noise - SMT 17 -5 -4 -3 -2 Pout Gain PAE 25 20 15 10 5 0 -15 -12 -9 -6 -3 0 INPUT POWER (dBm) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1040LP3CE v00.0112 GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz 80 Drain Bias Voltage +4V RF Input Power +5 dBm Channel Temperature 175 °C Continuous Pdiss (T = 85 °C) (derate 5.46 mW/°C above 85 °C) 0.49 W 72 Thermal Resistance (Channel to ground paddle) 183 °C/W 70 Storage Temperature -65 to +150 °C 68 Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 0, 100 V Idd 78 Idd (mA) 76 74 66 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 INPUT POWER (dBm) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Amplifiers - Low Noise - SMT Absolute Maximum Ratings Current vs. Input Power @ 33 GHz NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY. 3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 6. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.05mm MAX. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC1040LP3CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [1] Package Marking [2] H1040 XXXX [1] Max peak reflow temperature of 260 °C [2] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC1040LP3CE v00.0112 GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz Amplifiers - Low Noise - SMT Pin Descriptions 5 Pin Number Function Description 1, 2, 4, 9, 11, 12 GND These pins and package bottom must be connected to RF/DC ground. 3 RFIN This pin AC coupled and matched to 50 Ohms 5-8, 14 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/ DC ground externally. 10 RFOUT This pin AC coupled and matched to 50 Ohms 13, 15, 16 Vdd3, Vdd2, Vdd1 Drain bias voltages for the amplifier. See Application Circuit for required external componnets. Interface Schematic Application Circuit Capacitor Value C1 - C3 100 pF C4 - C6 10 nF C7 - C9 4.7 µF For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1040LP3CE v00.0112 GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 24 - 43.5 GHz Amplifiers - Low Noise - SMT Evaluation PCB List of Material for Evaluation PCB EVAL01-HMC1040LP3CE Item Description J1-J4 2.92 mm Connectors TP5-TP8 Test Points DC Pin C1 - C3 100 pF Capacitor, 0402 Pkg. C4 - C6 10 nF Capacitor, 0402 Pkg. C7 - C9 4.7 µF Capacitor, Tantalum U1 HMC1040LP3CE Amplifier PCB [2] 600-00271-00-2 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR [1] The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6