Si1000-C Ultra-Low Power 64 kB, 10-bit ADC MCU with Integrated 240–960 MHz Transceiver Transceiver Features Supply Voltage: 1.8 to 3.6 V - Typical sleep mode current < 0.1 µA; retains state and RAM contents over full supply range; fast wakeup of < 2 µs - Two built-in brown-out detectors cover sleep and active modes 10-Bit Analog to Digital Converter - Up to 300 ksps - Up to 18 external inputs - External pin or internal VREF (no external capacitor required) - Built-in temperature sensor (±3 °C); no calibration required - External conversion start input option - Autonomous burst mode with 16-bit automatic averaging accumulator Dual Comparators - Programmable hysteresis and response time - Configurable as interrupt or reset source - Low current (< 0.5 µA) in 1 or 2 system clocks - 25 MIPS peak throughput with 25 MHz clock Development Kit: Si1000DK-915, Si1000DK-470, Si1002DK-868 XTAL4 Programmable packet handler TX and RX 64 byte FIFOs Frequency hopping capability On-chip crystal tuning - Low power 20 MHz internal oscillator - External oscillator: crystal, RC, C, CMOS clock - smaRTClock oscillator: 32.768 kHz crystal or self-oscillate Ordering Part Number - Si1000-E-GM, 42-pin LGA (5 mm x 7 mm) 6-bit IREF 256 Byte SRAM 4096 Byte XRAM Precision 24.5 MHz Oscillator XCVR IREF0 PA Internal External VREF VREF TX A M U X 10-bit 300ksps ADC CRC Engine VDD VREF Temp Sensor CP0, CP0A CP1, CP1A SFR Bus AGC RXp RXn LNA Mixer GND + - PGA ADC + - Comparators Digital Peripherals Transceiver Control Interface Digital Modem Delta Sigma Modulator Digital Logic UART External Oscillator Circuit Timers 0, 1, 2, 3 smaRTClock Oscillator PCA/ WDT System Clock Configuration Wireless MCU Antenna diversity and transmit/receive switch control 64k Byte ISP Flash Program Memory Low Power 20 MHz Oscillator XTAL3 Auto-frequency calibration (AFC) (240-960 MHz) SYSCLK XTAL2 Data rate = 0.123 to 256 kbps Analog Peripherals VREG XTAL1 - CIP-51 8051 Controller Core C2D GND - 18.5 mA receive - 85 mA @ +20 dBm transmit ports UART operation; spread-spectrum mode for reduced EMI High-Speed 8051 µC Core - Pipe-lined instruction architecture; executes 70% of instructions VDD RF power consumption programmable counter array (PCA) system debug (no emulator required) Debug / Programming Hardware Max output power = +20 dBm Clock Sources - Precision internal oscillators: 24.5 MHz with ±2% accuracy sup- On-Chip Debug - On-chip debug circuitry facilitates full speed, non-intrusive in- C2CK/RST FSK, GFSK, and OOK modulation concurrently - 4352 bytes internal data RAM (256 + 4K) Wake Sensitivity = –121 dBm - Low power 32-bit smaRTClock - Four general purpose 16-bit counter/timers; six channel sectors; full read/write/erase functionality over the entire supply range Reset Frequency range = 240–960 MHz Digital Peripherals - 22 port I/O - Hardware enhanced UART, SPI and I2C serial ports available Memory - 64 kB flash; in-system programmable in 1024-byte Power On Reset/PMU - XIN XOUT OSC Priority Crossbar Decoder SMBus SPI 0 Copyright © 2010 by Silicon Laboratories Port I/O Config 22 ANALOG & DIGITAL I/O 1.15.10 Smart. Connected. Energy-Friendly Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com