Si1015-A Ultra-Low Power 8 kB, 12-bit ADC MCU with Integrated 240–960 MHz Transceiver Transceiver Features Supply Voltage: 0.9 to 3.6 V - Built-in dc-dc converter with 1.8 to 3.6 v output - Typical sleep mode current < 0.1 µA; retains state and RAM contents over full supply range; fast wakeup of < 2 µs - Two built-in brown-out detectors cover sleep and active modes 12-Bit Analog to Digital Converter - Up to 75 ksps - Up to 11 external inputs - External pin or internal VREF (no external capacitor required) - External conversion start input option - External conversion start input option - Autonomous Burst Mode with 16-bit automatic averaging - Frequency range = 240–960 MHz Sensitivity = –121 dBm FSK, GFSK, and OOK modulation Max output power = +13 dBm RF power consumption - 18.5 mA receive - 30 mA @ +13 dBm transmit - 18 mA @ +1 dBm transmit - accumulator - Built-in temperature sensor Dual Comparators - Programmable hysteresis and response time - Configurable as interrupt or reset source - Low current (< 0.5 µA) Data rate = 0.123 to 256 kbps Auto-frequency calibration (AFC) Antenna diversity and transmit/receive switch control Programmable packet handler TX and RX 64 byte FIFOs Frequency hopping capability On-chip crystal tuning Digital Peripherals - 15 port I/O - Hardware enhanced UART, SPI and I2C serial ports available concurrently Memory - 8 kB bytes Flash; in-system programmable in 512-byte - Low power 32-bit smaRTClock - Four general purpose 16-bit counter/timers; six channel sectors; full read/write/erase functionality over the entire supply range programmable counter array (PCA) Clock Sources - Precision internal oscillators: 24.5 MHz with ±2% accuracy sup- - 768 bytes internal data RAM On-Chip Debug - On-chip debug circuitry facilitates full speed, non-intrusive in- ports UART operation; spread-spectrum mode for reduced EMI system debug (no emulator required) High-Speed 8051 µC Core - Pipe-lined instruction architecture; executes 70% of instructions - Low power 20 MHz internal oscillator - External oscillator: crystal, RC, C, CMOS clock - smaRTClock oscillator: 32.768 kHz crystal or self-oscillate Ordering Part Number - Si1015-A-GM, 42-pin QFN, 5 x 7 mm2 in 1 or 2 system clocks - 25 MIPS peak throughput with 25 MHz clock Development Kit: Si1010DK CIP-51 8051 Controller Core Power On Reset/PMU 512 Byte XRAM C2D VDD/DC+ Power Net Analog Power GND/DC- VBAT GND XTAL1 XTAL2 XTAL3 XTAL4 VREG Digital Power External VREF VREF TX A M U X VDD VREF Temp Sensor CP1, CP1A SFR Bus AGC RXp RXn LNA Mixer GND + - PGA ADC + - Comparators Digital Peripherals Transceiver Control Interface Digital Modem Delta Sigma Modulator Digital Logic UART External Oscillator Circuit Timers 0, 1, 2, 3 smaRTClock Oscillator PCA/ WDT System Clock Configuration Wireless MCU PA Internal CP0, CP0A SYSCLK Low Power 20 MHz Oscillator IREF0 12-bit 75ksps ADC CRC Engine Precision 24.5 MHz Oscillator DC/DC Converter 6-bit IREF 256 Byte SRAM Debug / Programming Hardware RF XCVR (240-960 MHz) 8k Byte ISP Flash Program Memory Wake Reset C2CK/RST Analog Peripherals XIN XOUT OSC Priority Crossbar Decoder SMBus SPI 0 Copyright © 2010 by Silicon Laboratories Port I/O Config 15 ANALOG & DIGITAL I/O 1.15.10 Smart. Connected. Energy-Friendly Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com