Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC639ST89 / 639ST89E v03.0810 Typical Applications Features The HMC639ST89(E) is ideal for: Low Noise Figure: 2.3 dB • Cellular / PCS / 3G High P1dB Output Power: +22 dBm • WiMAX, WiBro, & Fixed Wireless High Output IP3: +38 dBm • CATV & Cable Modem Gain: 13 dB 9 • Microwave Radio 50 Ohm I/O’s - No External Matching • IF and RF Sections Industry Standard SOT89 Package AMPLIFIERS - LINEAR & POWER - SMT HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Functional Diagram General Description The HMC639ST89(E) is a GaAs pHEMT, High Linearity, Low Noise, Wideband Gain Block Amplifier covering 0.2 to 4.0 GHz. Packaged in an industry standard SOT89, the amplifier can be used as either a cascadable 50 Ohm gain stage, a PA Pre-Driver, a Low Noise Amplifier, or a Gain Block with up to +22 dBm output power. This versatile Gain Block Amplifier is powered from a single +5V supply and requires no external matching components. The internally matched topology permits this amplifier to be readily ported between virtually any printed circuit board material, regardless of its dielectric constant, thickness, or composition. Electrical Specifications, Vs= 5V, TA = +25° C Parameter Min Frequency Range Gain Typ. Max Min. 0.7 - 2.2 10 Gain Variation Over Temperature 13 0.01 Input Return Loss Typ. Max. 0.2 - 4.0 6 0.02 12 GHz 10 0.01 Units dB 0.02 12 dB/ °C dB Output Return Loss 12 14 dB Reverse Isolation 20 20 dBm Output Power for 1 dB Compression (P1dB) 19 21 20 22 dB Output Third Order Intercept (IP3) 35 38 35 38 dBm 90 110 90 110 Noise Figure Supply Current (Icq) 2.3 2.5 120 dB 120 mA Note: Data taken with broadband bias tee on device output. 9-1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC639ST89 / 639ST89E v03.0810 HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Gain vs. Temperature 20 16 15 14 10 12 S21 S11 S22 0 -5 10 8 6 -10 4 -15 2 -20 0 0 1 2 3 4 5 6 0 1 FREQUENCY (GHz) 3 4 5 Output Return Loss vs. Temperature 0 0 +25C +85C -40C -5 RETURN LOSS (dB) RETURN LOSS (dB) 2 FREQUENCY (GHz) Input Return Loss vs. Temperature -10 -15 -20 +25C +85C -40C -5 -10 -15 -20 0 1 2 3 4 5 0 1 FREQUENCY (GHz) 3 4 5 4 5 Noise Figure vs. Temperature 10 -5 8 NOISE FIGURE (dB) 0 +25C +85C -40C -10 2 FREQUENCY (GHz) Reverse Isolation vs. Temperature REVERSE ISOLATION (dB) 9 +25C +85C -40C -15 -20 +25C +85C -40C 6 AMPLIFIERS - LINEAR & POWER - SMT 5 GAIN (dB) RESPONSE (dB) Broadband Gain & Return Loss 4 2 -25 0 0 1 2 3 FREQUENCY (GHz) 4 5 0 1 2 3 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-2 HMC639ST89 / 639ST89E v03.0810 HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Psat vs. Temperature 30 30 25 25 20 20 Psat (dBm) 9 P1dB (dBm) P1dB vs. Temperature 15 +25C +85C -40C 10 10 5 0 0 0 1 2 3 4 0 1 2 FREQUENCY (GHz) 4 Power Compression @ 2200 MHz 32 Pout (dBm), GAIN (dB), PAE (%) 32 Pout (dBm), GAIN (dB), PAE (%) 3 FREQUENCY (GHz) Power Compression @ 850 MHz Pout Gain PAE 24 16 8 0 -8 -20 -12 -4 4 12 16 8 0 -8 -20 20 Pout Gain PAE 24 -12 -4 INPUT POWER (dBm) 35 25 20 1 2 FREQUENCY (GHz) 20 3 4 160 160 140 120 Gain P1dB Psat IP3 140 120 100 100 80 Is 80 60 60 40 40 20 20 0 0 4.5 4.75 5 5.25 5.5 Vs (V) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] Is (mA) 0 dBm 5 dBm 10 dBm GAIN (dB), P1dB (dBm), Psat (dBm), IP3 (dBm) 40 0 12 Gain, Power, Output IP3 & Supply Current vs. Supply Voltage @ 850 MHz 45 30 4 INPUT POWER (dBm) Output IP3 vs. Output Tone Power IP3 (dBm) AMPLIFIERS - LINEAR & POWER - SMT 5 9-3 +25C +85C -40C 15 HMC639ST89 / 639ST89E v03.0810 HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Absolute Maximum Ratings +5.5 Volts RF Input Power (RFIN)(Vcc = +5 Vdc) +15 dBm Channel Temperature 150 °C Continuous Pdiss (T = 85 °C) (derate 13.3 mW/°C above 85 °C) 0.86 W Thermal Resistance (Channel to lead) 75.6 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: MOLDING COMPOUND MP-180S OR EQUIVALENT. 2. LEAD MATERIAL: Cu w/ Ag SPOT PLATING. 3. LEAD PLATING: 100% MATTE TIN. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS] 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. AMPLIFIERS - LINEAR & POWER - SMT Collector Bias Voltage (Vcc) Package Information Part Number Package Body Material Lead Finish MSL Rating HMC639ST89 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC639ST89E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H639 XXXX H639 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-4 HMC639ST89 / 639ST89E v03.0810 HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Pin Descriptions Pin Number Function Description 1 RFIN This pin is DC coupled. An off-chip DC blocking capacitor is required. 3 RFOUT RF Output and DC BIAS for the amplifier. See Application Circuit for off-chip components. 2, 4 GND These pins and package bottom must be connected to RF/DC ground. AMPLIFIERS - LINEAR & POWER - SMT 9 9-5 Interface Schematic Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC639ST89 / 639ST89E v03.0810 HIGH IP3, LOW NOISE AMPLIFIER, 0.2 - 4.0 GHz Evaluation PCB List of Materials for Evaluation PCB 119394 Item Description J1 - J2 PCB Mount SMA Connector J3 - J4 DC Pin C1 - C3 100 pF Capacitor, 0402 Pkg. C4 1000 pF Capacitor, 0603 Pkg. C5 2.2 µF Capacitor, Tantalum L1 47 nH Inductor, 0603 Pkg. U1 HMC639ST89(E) PCB [2] 119392 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [1] The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. AMPLIFIERS - LINEAR & POWER - SMT 9 [2] Circuit Board Material: FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9-6