MSP3V3, MSP5.0A Datasheet

MSP3V3, MSP5.0A
www.vishay.com
Vishay General Semiconductor
Surface Mount TRANSZORB® Transient Voltage Suppressors
FEATURES
• Very low profile - typical height of 0.65 mm
eSMP ® Series
Available
• Ideal for automated placement
• Oxide planar chip junction
• Uni-directional polarity only
• Peak pulse power: 150 W (10/1000 μs)
Top View
• ESD capability: 15 kV (air), 8 kV (contact)
Bottom View
• Meets MSL level 1, per J-STD-020C, LF maximum peak of
260 °C
MicroSMP
• AEC-Q101 qualified
• Not recommended for PCB bottom side wave mounting
PRIMARY CHARACTERISTICS
VWM
3.3 V to 5.0 V
VBR
4.1 V to 7.07 V
PPPM
150 W
TJ max.
150 °C
Polarity
Uni-directional
Package
MicroSMP
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Case: MicroSMP
Molding compound meets UL 94 V-0 flammability rating
Base P/N-M3 - halogen-free, RoHS-compliant, and
commercial grade
Base P/NHM3 - halogen-free, RoHS-compliant, and
automotive grade
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and lighting
on ICs, MOSFET, signal lines of sensor units for protecting
sensitive equipment against transient overvoltages.
Terminals: Matte tin plated leads, solderable per
J-STD-002 and JESD 22-B102
M3 suffix meets JESD 201 class 2 whisker test, HM3 suffix
meets JESD 201 class 2 whisker test
Polarity: Color band denotes the cathode end
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
Peak power dissipation with a 10/1000 μs waveform (fig. 1)
PPPM
Peak pulse current with a 10/1000 μs waveform
IPPM
VALUE
UNIT
(1)(2)
150
W
(1)
See next table
A
(2)
Power dissipation
TM = 120 °C
PD
1.0
W
Power dissipation
TA = 25 °C
PD (3)
0.5
W
TJ, TSTG
- 55 to + 150
°C
Operating junction and storage temperature range
Notes
(1) Non-repetitive current pulse, per fig. 1
(2) Mounted on 6.0 mm x 6.0 mm copper pads to each terminal
(3) Mounted on minimum recommended pad layout
Revision: 10-Dec-13
Document Number: 88486
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MSP3V3, MSP5.0A
www.vishay.com
Vishay General Semiconductor
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE
TYPE
BREAKDOWN
VOLTAGE
VBR AT IT (1)
(V)
DEVICE
MARKING
CODE
MIN.
MAX.
TEST
CURRENT
IT
(mA)
STAND-OFF
VOLTAGE
VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
CURRENT
IR AT VWM
(μA)
MAXIMUM
VC AT IPPM
MAXIMUM
VC AT IPPM
RD
10/1000 μs
VC (V) IPPM (A)
RD
8/20 μs
RD () VC (V) IPPM (A)
RD ()
MSP3V3
KC
4.10
5.10
1.0
3.3
200
7.6
19.7
0.127
11.5
87
0.074
MSP5.0A
AE
6.40
7.07
10
5.0
100
9.2
16.3
0.131
13.4
75
0.085
Notes
• To calculate maximum clamping voltage at surge current uses the following formula: VCL max. = RD x IPP + VBR max.
(1) Pulse test: t  50 ms
p
THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
RJA
Typical thermal resistance
VALUE
(1)
UNIT
250
RJM (2)
°C/W
30
Notes
(1) Free air, mounted on recommended PCB 1 oz. pad area; thermal resistance R
JA - junction to ambient
(2) Units mounted on PCB with 6.0 mm x 6.0 mm copper pad areas; R
JM - junction to mount
IMMUNITY TO STATIC ELECTRICAL DISCHARGE TO THE FOLLOWING STANDARDS
(TA = 25 °C unless otherwise noted)
STANDARD
TEST TYPE
AEC-Q101-001
IEC 61000-4-2
TEST CONDITIONS
Human body model (contact mode)
(2)
C = 100 pF, R = 1.5 k
Human body model (air discharge mode)
(1)
C = 150 pF, R = 330 
SYMBOL
VC
CLASS
VALUE
H3B
> 8 kV
4
> 15 kV
Notes
(1) Immunity to IEC 61000-4-2 air discharge mode has a typical performance > 30 kV
(2) System ESD standard
ORDERING INFORMATION (Example)
PREFERRED P/N
UNIT WEIGHT (g)
PREFERRED PACKAGE CODE
BASE QUANTITY
DELIVERY MODE
MSP3V3-M3/89A
0.006
89A
4500
7" diameter plastic tape and reel
MSP3V3HM3/89A (1)
0.006
89A
4500
7" diameter plastic tape and reel
MSP5.0A-M3/89A
0.006
89A
4500
7" diameter plastic tape and reel
0.006
89A
4500
7" diameter plastic tape and reel
MSP5.0AHM3/89A
(1)
Note
(1) Automotive grade
Revision: 10-Dec-13
Document Number: 88486
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MSP3V3, MSP5.0A
www.vishay.com
Vishay General Semiconductor
RATINGS AND CHARACTERISTICS CURVES
(TA = 25 °C unless otherwise noted)
1000
TJ = 25 °C
Pulse Width (td) is
defined as the Point
Where the Peak Current
decays to 50 % of IPPM
tr = 10 μs
tr = 8 μs
Peak Value
IPPM
100
Half Value - IPP
IPPM
2
50
td = 1000 μs
td = 20 μs
td
0
0
1.0
2.0
3.0
Measured at Zero Bias
CJ - Junction Capacitance (pF)
IPPM - Peak Pulse Current (% IRSM)
150
Measured at Stand-off
Voltage, VWM
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
100
4.0
3
t - Time (ms)
Fig. 1 - Pulse Waveform
4.5
5
5.5
6
1.2
Non-Repetitive Pulse
Waveform Shown in Fig. 1
TA = 25 °C
10
1
0.1
TA = TM, Mounted on
6.0 mm x 6.0 mm Copper Pad
PD - Power Dissipation (W)
PPPM - Peak Pulse Power (kW)
4
Fig. 4 - Typical Junction Capacitance
100
0.24" x 0.24" (6.0 mm x 6.0 mm)
Copper Pad Areas
1.0
0.8
0.6
Mounted on Minimum
Recommende Pad Area
0.4
0.2
0.0
0.01
0.1
1
10
100
1000
0
10 000
25
75
50
100
125
150
175
td - Pulse Width (μs)
Ambient Temperature (°C)
Fig. 2 - Peak Pulse Power Rating Curve
Fig. 5 - Power Dissipation Derating Curve
1000
100
Transient Thermal Impedance (°C/W)
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage (%)
3.5
VWM - Reverse Stand-Off Voltage (V)
75
50
25
0
0
25
50
75
100
125
150
175
TJ - Initial Temperature (°C)
Fig. 3 - Pulse Power or Current vs. Initial Junction Temperature
Revision: 10-Dec-13
Junction to Ambient
100
10
0.01
0.1
1
10
100
1000
t - Pulse Duration (s)
Fig. 6 - Typical Transient Thermal Impedance
Document Number: 88486
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MSP3V3, MSP5.0A
www.vishay.com
Vishay General Semiconductor
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
MicroSMP
0.059 (1.50)
0.043 (1.10)
Cathode Band
0.055 (1.40)
0.047 (1.20)
0.030 (0.75)
0.022 (0.55)
0.039 (0.98)
0.031 (0.78)
0.091 (2.30)
0.083 (2.10)
0.106 (2.70)
0.091 (2.30)
0.030 (0.75)
0.022 (0.55)
Mounting Pad Layout
0.079
(2.00)
0.029 (0.73)
0.025 (0.63)
0.043
(1.10)
0.011 (0.27)
0.005 (0.12)
Revision: 10-Dec-13
0.032
(0.80)
0.032
(0.80)
0.020 (0.50)
Document Number: 88486
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000