TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC710LC5 v04.0514 Features The HMC710LC5 is ideal for: High Conversion Gain: 12 dB • Point-to-Point and Point-to-Multi-Point Radio Sideband Rejection: -20 dBc • Military Radar, EW & ELINT 2 LO to RF Isolation: 12 dB • Satellite Communications Output IP3: +30 dBm • Sensors 32 Lead 5x5mm SMT Package: 25mm² Functional Diagram General Description TE Typical Applications B SO LE The HMC710LC5 is a compact GaAs MMIC I/Q upconverter in a leadless RoHS compliant SMT package. This device provides a small signal conversion gain of 12 dB with -20 dBc of sideband rejection. The HMC710LC5 utilizes a driver amplifier preceded by an I/Q mixer where the LO is driven by an active x2 multiplier. IF1 and IF2 mixer inputs are provided and an external 90° hybrid is needed to select the required sideband. The I/Q mixer topology reduces the need for filtering of the unwanted sideband. The HMC710LC5 is a much smaller alternative to hybrid style single sideband upconverter assemblies and it eliminates the need for wire bonding by allowing the use of surface mount manufacturing techniques. Electrical Specifications, TA = +25 °C, IF = 1000 MHz, LO = +6 dBm, Vdd1, 2, 3 = +5V, Idd2 + Idd3 = 150 mA [1][3] Parameter Min. Frequency Range, RF O MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz Typ. Max. 16 - 21 Units GHz Frequency Range, LO 7.5 - 11 GHz Frequency Range, IF DC - 3.5 GHz 7 12 dB -12 -20 dBc 20 dBm 2 LO to RF Isolation 12 dB 2 LO to IF Isolation [2] 20 dB Conversion Gain Sideband Rejection 1 dB Compression (Output) IP3 (Output) 30 dBm Supply Current Idd1 52 90 108 Supply Current Idd2 24 30 mA mA Supply Current Idd3 96 120 mA [1] Unless otherwise noted all measurements performed with high side LO, IF = 1000 MHz and external 90° IF hybrid. [2] Data taken without external IF hybrid. [3] Adjust Vgg between -2 to 0V to achieve Idd2 + Idd3 = 150 mA Typical. 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz Data Taken as SSB Upconverter with External IF Hybrid 18 CONVERSION GAIN (dB) 20 18 16 14 12 8 +25 C +85 C -40 C 6 14 12 10 8 6 4 4 16 17 18 19 20 21 22 16 17 18 Conversion Gain vs. IF Frequency 20 20 21 22 21 22 Conversion Gain vs. Idd2 + Idd3 20 18 18 IF = 100MHz IF = 1000MHz 16 12 10 8 4 15 B SO 14 6 16 17 18 19 20 21 22 23 Idd1+Idd2 = 110mA Idd1+Idd2 = 130mA Idd1+Idd2 = 150mA 16 14 12 10 8 6 4 24 16 17 18 RF FREQUENCY (GHz) 0 20 0 -5 RETURN LOSS (dB) RF LO -5 19 RF FREQUENCY (GHz) IF Return Loss [1] O RF, LO Return Loss RETURN LOSS (dB) 19 RF FREQUENCY (GHz) LE RF FREQUENCY (GHz) CONVERSION GAIN (dB) +3 dBm +6 dBm +9 dBm 16 TE 10 CONVERSION GAIN (dB) CONVERSION GAIN (dB) 20 -10 -15 -20 MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT Conversion Gain vs. LO Drive Conversion Gain vs. Temperature -10 -15 -20 IF1 IF2 -25 -25 2 4 6 8 10 12 14 16 FREQUENCY (GHz) 18 20 22 24 -30 0 1 2 3 4 5 6 7 8 IF FREQUENCY (GHz) [1] Data taken without external IF hybrid For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz Data Taken as SSB Upconverter with External IF Hybrid Side Band Rejection Output P1dB vs. Temperature 23 -10 P1dB (dBm) 22 -30 19 +25 C +85 C -40 C 17 16 16 17 18 19 20 21 22 16 RF FREQUENCY (GHz) 17 18 19 20 21 22 21 22 21 22 LE RF FREQUENCY (GHz) Output IP3 vs. Temperature Output IP3 vs. LO Drive 34 34 32 32 30 28 B SO IP3 (dBm) 20 18 +25 C +85 C -40 C 26 24 16 17 18 19 20 21 30 +3 dBm +6 dBm 28 26 24 22 16 17 RF FREQUENCY (GHz) O Output IP3 vs. IF Frequency 34 32 18 19 20 RF FREQUENCY (GHz) Output IP3 vs. Idd2 + Idd3 34 IF = 100MHz IF = 1000MHz 32 IP3 (dBm) 30 28 26 30 28 Idd1+Idd2 = 110mA Idd1+Idd2 = 130mA Idd1+Idd2 = 150mA 26 24 24 16 17 18 19 20 RF FREQUENCY (GHz) 3 21 TE -20 IP3 (dBm) SIDEBAND REJECTION (dBc) 24 -40 IP3 (dBm) MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT 0 21 22 16 17 18 19 20 RF FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz 0 0 -10 -10 -20 -20 -30 2LO/RF IF1/RF 2LO/IF1 IF2/RF 2LO/IF2 -40 -40 -50 TE -50 -30 -60 LO/RF LO/IF1 LO/IF2 -60 -70 -70 16 17 18 19 20 21 22 16 RF FREQUENCY (GHz) 17 18 19 20 21 22 MxN Spurious Outputs [1] LE RF FREQUENCY (GHz) Harmonics of LO nLO mIF 0 1 2 3 0 xx 19 48 xx 1 61 0 66 xx nLO Spur @ IF Port 4 LO Freq. (GHz) 1 2 3 4 xx 8 42 21 25 64 xx 35 24 47 50 32 53 xx xx 10 38 19 49 47 61 38 72 xx xx 11 42 25 44 51 52 62 73 xx xx 12 34 18 50 xx IF = 1 GHz @ 0 dBm 13 39 32 55 xx LO = 9.75 GHz @ +6 dBm 14 22 35 52 xx 3 4 B SO 9 35 2 Data taken without IF hybrid O All values in dBc below RF power level (-1IF + 2LO) MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT Isolations with LO [1] ISOLATION (dB) ISOLATION (dB) Isolations with 2LO [1] [1] Data taken without external IF hybrid For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz 5.25V Gate Bias Voltage (Vgg) -3 to 0V IF Input Power (IF1, IF2) 20 dBm LO Drive (LO IN) 20 dBm Channel Temperature 175 °C Continuous Pdiss (T = 85°C) (derate 16.2 mW/°C above 85°C) 1.46 mW Thermal Resistance (channel to ground paddle) 61.8 °C/W -65 to +150 °C Operating Temperature -55 to +85 °C ESD Sensitivity (HBM) Class 1A LE Storage Temperature ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS TE Drain Bias Voltage (Vdd1, 2, 3) B SO Outline Drawing O MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT Absolute Maximum Ratings NOTES: 1.. PACKAGE BODY MATERIAL: ALUMINA 2.. LEAD AND GROUND PADDLE PLATING: 30 - 80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKLE 3.. DIMENSIONS ARE IN INCHES [MILLIMETERS] 4.. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 5.. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM 6.. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND Package Information Part Number Package Body Material Lead Finish HMC710LC5 Alumina, White Gold over Nickel MSL Rating MSL3 [1] Package Marking [2] H710 XXXX [1] Max peak reflow temperature of 260 °C [2] 4-Digit lot number XXXX 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz 100 pF C4 - C7 1000 pF C8 - C11 2.2 µF O C1 - C3 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT B SO LE TE Typical Application 6 HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz 7 Function Description Interface Schematic 1 - 5, 7, 8, 11, 16, 17, 19, 20, 22 - 28 N/C No Connection required. These pins may be connected to RF/DC ground without affecting performance. 6 Vdd1 Power supply voltage for x2 multiplier. See application circuit for required external components. 9 LOIN This pin is AC coupled and matched to 50 Ohms. 10, 13, 15, 30, 32 GND These pins and package bottom must be connected to RF/DC ground. 12 Vgg Gate control for RF amplifier, please follow “MMIC Amplifier Biasing Procedure” application note. See application circuit for required external components 14 RFOUT This pin is AC coupled and matched to 50 Ohms. LE TE Pin Number Vdd2, Vdd3 Power supply voltage for RF amplifier. See application circuit for required external components. 29 IF1 31 IF2 Differential IF input pins. For applications not requiring operation to DC, an off chip DC blocking capacitor should be used. For operation to DC this pin must not source/sink more than 3mA of current or part non function and possible part failure will result. B SO 18, 21 O MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT Pin Descriptions For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC710LC5 v04.0514 GaAs MMIC I/Q UPCONVERTER 16 - 21 GHz List of Materials for Evaluation PCB 120412 [1] Item Description J1, J2 PCB Mount SMA SRI Connector J3, J4 PCB Mount SMA Connector J5 - J12 DC Pin C1 - C3 100 pF Capacitor, 0402 Pkg. C4 1000 pF Capacitor, 0402 Pkg. C5 - C7 1000 pF Capacitor, 0603 Pkg. C8 - C11 2.2 µF Tantalum Capacitor Case A U1 HMC710LC5 Upconverter PCB [2] 120410 Evaluation Board The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT O B SO LE TE Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR, FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8