TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Typical Applications Features The HMC130 is ideal for: Conversion Loss: 7 dB • Microwave & VSAT Radios LO to RF and IF Isolation: >32 dB • Test Equipment Input IP3: +17 dBm • Military EW, ECM, C3I No DC Bias Required • Space Telecom Die Size: 1.45 x 1.3 x 0.1 mm Functional Diagram General Description TE B SO LE The HMC130 chip is a miniature double-balanced mixer which can be used as an upconverter or downconverter in the 6 to 11 GHz band. The chip can be integrated directly into hybrid MMIC’s without DC bias or external baluns to provide an extremely compact mixer. It is ideally suited for applications where small size, no DC Bias, and consistent IC performance are required. This mixer can operate over a wide LO drive input of +9 to +15 dBm. It performs equally well as a Bi-Phase modulator or demodulator. See HMC137 data sheet. Electrical Specifi cations, TA = +25° C, LO Drive = +15 dBm O MIXERS - DOUBLE-BALANCED - CHIP 4 Parameter Min. Typ. Frequency Range, RF & LO 6.0 - 11.0 Frequency Range, IF DC - 2.0 Max. GHz GHz Conversion Loss 7 9 dB Noise Figure (SSB) 7 9 dB LO to RF Isolation 32 40 LO to IF Isolation 35 40 dB IP3 (Input) 13 17 dBm IP2 (Input) 45 55 dBm 1 dB Gain Compression (Input) 6 9 dBm * Unless otherwise noted, all measurements performed as downconverter, IF = 100 MHz 4 - 14 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com dB HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Conversion Gain vs. Temperature @ LO = +15 dBm Isolation @ LO = +15 dBm 0 -10 ISOLATION (dB) -10 +25 C +85 C -55 C -15 -20 -25 RF/IF LO/RF LO/IF -30 -35 4 -40 TE CONVERSION GAIN (dB) -15 -5 -20 -50 6 7 8 9 10 FREQUENCY (GHz) 11 Conversion Gain vs. LO Drive 13 5 7 8 9 10 FREQUENCY (GHz) 11 12 13 -10 B SO -5 +9 dBm +11 dBm +13 dBm +15 dBm -15 5 6 7 8 9 10 FREQUENCY (GHz) 11 12 RETURN LOSS (dB) 0 -20 -10 -15 LO RF -20 -25 4 5 6 7 8 9 10 Frequency (GHz) 11 12 13 14 Upconverter Performance Conversion Gain vs. LO Drive O 0 CONVERSION GAIN (dB) 0 -5 -10 IF CONVERSION LOSS IF RETURN LOSS (dB) -15 -5 13 IF Bandwidth @ LO = +15 dBm RESPONSE (dB) 6 Return Loss @ LO = +15 dBm 0 CONVERSION GAIN (dB) 12 LE 5 -20 -5 MIXERS - DOUBLE-BALANCED - CHIP -45 -10 +9 dBm +11 dBm +13 dBm +15 dBm -15 -20 0 0.5 1 1.5 2 2.5 FREQUENCY (GHz) 3 3.5 4 5 6 7 8 9 10 FREQUENCY (GHz) 11 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 13 4 - 15 HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Input IP3 vs. Temperature @ LO = +15 dBm Input IP3 vs. LO Drive 30 30 +11 dBm +13 dBm +15 dBm IP3 (dBm) 20 15 10 10 6 7 8 9 10 FREQUENCY (GHz) 11 4 13 5 6 7 8 9 10 11 12 13 FREQUENCY (GHz) Input IP2 vs. Temperature @ LO = +15 dBm Input IP2 vs. LO Drive 80 80 75 +11 dBm +13 dBm +15 dBm 70 65 60 55 50 45 40 5 75 6 7 8 9 10 FREQUENCY (GHz) 11 12 13 Input P1dB vs. Temperature @ LO = +15 dBm 65 60 55 50 45 40 5 6 7 8 9 10 FREQUENCY (GHz) 11 12 O nLO Spur @ RF Port 12 +25 C +85 C -55 C 10 LO Freq. (GHz) 1 2 3 7 8 9 10 11 FREQUENCY (GHz) 12 4 9.0 45 56 46 79 10.5 42 56 56 62 12.0 36 54 43 60 13.5 35 69 38 57 15.0 35 58 44 ? 16.5 32 49 40 ? LO = +13 dBm All values in dBc below input LO level measured at RF port 8 6 13 Harmonics of LO 13 11 +25 C +85 C -55 C 70 B SO IP2 (dBm) 12 LE 5 9 4 - 16 20 TE 15 P1dB (dBm) MIXERS - DOUBLE-BALANCED - CHIP 4 +25 C +85 C -55 C 25 IP2 (dBm) IP3 (dBm) 25 13 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Absolute Maximum Ratings nLO 0 1 2 3 4 0 xx 17.16 26.0 9.0 37.33 1 12.83 0 39.83 53.0 33.66 2 69.0 76.5 57.83 76.83 71.0 3 75.33 76.16 78 61.66 78.16 4 66.83 74.83 77.33 78.16 79.66 LO Drive +27 dBm Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C %,%#42/34!4)#3%.3)4)6%$%6)#% /"3%26%(!.$,).'02%#!54)/.3 TE mRF RF Freq. = 9.1 GHz @ -10 dBm LO Freq. = 9.0 GHz @ +13 dBm Measured as downconverter O B SO LE Outline Drawing Die Packaging Information [1] Standard Alternate WP-3 (Waffle Pack) [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. 4 MIXERS - DOUBLE-BALANCED - CHIP MxN Spurious @ IF Port NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM] 2. BOND PADS ARE .004” SQUARE 3. TYPICAL BOND PAD SPACING CENTER TO CENTER .1 IS .006” EXCEPT AS SHOWN 4. DIE THICKNESS = .004” [.100 MM] 5. BACKSIDE METALIZATION: GOLD 6. BACKSIDE METAL IS GROUND 7. BOND PAD METALIZATION: GOLD For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 4 - 17 HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Pad Descriptions Pad Number Function Description 1 RF This pin is DC coupled and matched to 50 Ohms. 2 LO This pin is DC coupled and matched to 50 Ohms. IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC this pin must not source or sink more than 2mA of current or die non-function and possible die failure will result. GND The backside of the die must connect to RF ground. 4 - 18 TE LE B SO 3 O MIXERS - DOUBLE-BALANCED - CHIP 4 Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC130 v04.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 6 - 11 GHz Handling Precautions Follow these precautions to avoid permanent damage. O Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting 4 MIXERS - DOUBLE-BALANCED - CHIP B SO LE TE Assembly Diagram The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 4 - 19