PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Typical Applications
Features
High Dynamic Range Infrastructure:
Input IP3: +31 dBm
• GSM, GPRS & EDGE
High Side LO
• CDMA & W-CDMA
Ultra Small MSOP8 Package: 14.8mm2
• Cable Modem Termination Systems
No External Components
Included in the HMC-DK002 Designer’s Kit
9
General Description
MIXERS - HIGH IP3 - SMT
Functional Diagram
The HMC402MS8 & HMC402MS8E are high dynamic
range passive MMIC mixers in plastic surface mount
8 lead Mini Small Outline Packages (MSOP) covering 1.8 to 2.2 GHz. Excellent input IP3 performance
of +31 dBm for down conversion and +27 dBm for up
conversion is provided for 2.5G & 3G GSM/CDMA
based UMTS or PCS applications at an LO drive of
+17dBm. With a 1dB compression of +21 dBm, the RF
port will accept a wide range of input signal levels.
Conversion loss is 8.5dB typical and LO isolations are
maintained at 24 to 30 dB. This miniature single-ended monolithic GaAs FET mixer does not require any
external components or bias. The broad 50 to
500 MHz IF frequency response will satisfy many
UMTS/PCS transmit or receive frequency plans
configured for high side LO. The HMC402MS8(E)
input IP3 performance coupled with its high P1dB
rivals traditional active FET mixers while offering
a much smaller 14.8mm2 standard IC footprint, and
no DC bias.
Electrical Specifi cations, TA =25 °C, LO = +17 dBm, IF = 300 MHz*
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
1.8 - 2.0
2.0 - 2.2
GHz
Frequency Range, LO
1.85 - 2.5
2.05 - 2.53
GHz
Frequency Range, IF
DC - 500
DC - 330
MHz
Conversion Loss
8.8
10.5
8.5
10.5
dB
Noise Figure (SSB)
8.8
10.5
8.5
10.5
dB
LO to RF Isolation
24
30
21
25
dB
LO to IF Isolation
19
24
24
28
dB
IP3 (Input)
27
30
27
31
dBm
1 dB Gain Compression (Input)
18
21
18
22
dBm
+16 to +18
dBm
LO Input Drive Level (Typical)
+16 to +18
*Unless otherwise noted, all measurements performed as a downconverter with high side LO & IF = 300 MHz.
9 - 246
Units
Frequency Range, RF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Isolation @ LO = +17 dBm
0
0
-5
-10
-10
+ 25C
+ 85C
- 40C
-15
9
-40
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
2.2
2.3
Return Loss @ LO = +17 dBm
Conversion Gain vs. LO Drive
0
0
-5
-5
RETURN LOSS (dB)
CONVERSION GAIN (dB)
-20
-30
-20
-10
LO = +15dBm
LO = +16dBm
LO = +17dBm
LO = +19dBm
-15
-10
RF
LO
-15
-20
-20
-25
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
1.5
2.3
1.75
2
2.25
RF FREQUENCY (GHz)
2.5
Unconverter Performance
Conversion Gain @ LO = +17 dBm
IF Bandwidth @ LO = +17 dBm
0
CONVERSION GAIN (dB)
0
-5
RESPONSE (dB)
RF TO IF
LO TO RF
LO TO IF
MIXERS - HIGH IP3 - SMT
ISOLATION (dB)
CONVERSION GAIN (dB)
Conversion Gain vs.
Temperature @ LO = +17 dBm
-10
CONVERSION GAIN
RETURN LOSS (dB)
-15
-5
-10
-15
-20
-20
0
0.1
0.2
0.3
0.4
0.5
0.6
IF FREQUENCY (GHz)
0.7
0.8
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
*Unless otherwise noted, all measurements performed as a downconverter with high side LO & IF = 300 MHz.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 247
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Input IP3 vs.
Temperature @ LO = +17 dBm
40
35
35
INPUT IP3 (dBm)
40
30
LO = +15 dBm
LO = +16 dBm
LO = +17 dBm
LO = +19 dBm
25
30
+ 25C
+ 85C
- 40C
25
20
20
60
90
120
150
180
210
240
IF FREQUENCY (MHz)
270
300
Input IP3 vs.
IF Frequency, RF = 2.15 GHz
1.7
40
40
35
35
30
LO = +15dBm
LO = +16dBm
LO = +17dBm
LO = +19dBm
25
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
2.2
2.3
2.2
2.3
Input IP3 vs. LO Drive
INPUT IP3 (dBm)
INPUT IP3 (dBm)
MIXERS - HIGH IP3 - SMT
9
INPUT IP3 (dBm)
Input IP3 vs.
IF Frequency, RF = 1.95 GHz
30
LO = +15 dBm
LO = +16 dBm
LO = +17 dBm
LO = +19 dBm
25
20
20
60
90
120
150
180
210
240
IF FREQUENCY (MHz)
270
300
Input P1dB vs.
Temperature @ LO = +17 dBm
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
Upconverter IP3 vs.
LO Drive, IF = 200 MHz
35
25
30
INPUT IP3 (dBm)
INPUT P1dB (dBm)
23
21
19
+ 25C
+ 85C
- 40C
17
LO = +15dBm
LO = +16dBm
LO = +17dBm
LO = +19dBm
20
15
15
1.7
25
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
*Unless otherwise noted, all measurements performed as a downconverter with high side LO & IF = 300 MHz.
9 - 248
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Input IP2 vs. LO Drive
40
40
35
35
30
+ 25C
+ 85C
- 40C
25
30
20
9
LO = +15 dBm
LO = +16 dBm
LO = +17 dBm
LO = +19 dBm
25
20
1.6
1.7
1.8
1.9
2
2.1
2.2
RF FREQUENCY (GHz)
2.3
2.4
MxN Spurious Outputs
1.6
1.7
1.8
1.9
2
2.1
2.2
RF FREQUENCY (GHz)
2.3
2.4
Harmonics of LO
nLO
nLO Spur @ RF Port
mRF
0
1
2
3
4
LO Freq (GHz)
1
2
3
4
0
xx
-7
-3
-1
11
1.8
40
30
51
57
1
5
0
27
54
30
2
30
29
51
53
2
62
64
48
65
70
2.2
26
32
51
50
3
81
81
82
81
80
2.4
24
36
53
49
4
77
81
80
83
82
2.6
23
43
59
53
2.8
22
41
51
71
RF Freq = 1.9 GHz @ -10 dBm
LO Freq = 2.2 GHz @ +17 dBm
All values in dBc relative to the IF power level.
Measured as a downconverter.
LO = +17 dBm
All values are in dBc below input LO level @ RF port.
MIXERS - HIGH IP3 - SMT
INPUT IP2 (dBm)
INPUT IP2 (dBm)
Input IP2 vs. Temperature
@ LO = +17 dBm
Absolute Maximum Ratings
RF/IF Input
+27 dBm
LO Drive
+27 dBm
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
IF DC Current
±40 mA
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
*Unless otherwise noted, all measurements performed as a downconverter with high side LO & IF = 300 MHz.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 249
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Outline Drawing
MIXERS - HIGH IP3 - SMT
9
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC402MS8
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC402MS8E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H402
XXXX
[2]
H402
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
9 - 250
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Pin Descriptions
Function
Description
1
LO
This pin is AC coupled & matched to 50 Ohms
from 1.8 to 2.2 GHz. Blocking capacitors are required if line
potential is not equal to 0V.
2, 4
N/C
Not connected.
3, 6, 7
GND
This pin must be connected to RF ground.
5
IF Port
This pin is DC coupled. For applications not requiring
operation to DC this port should be DC blocked externally
using a series capacitor. Choose value of capacitor to
pass IF frequency desired. For operation to DC, this
pin must not sink/source more than 40 mA of current or
failure may result.
8
RF Port
This pin is DC coupled & matched to 50 Ohms
from 1.8 to 2.2 GHz
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9
MIXERS - HIGH IP3 - SMT
Pin Number
9 - 251
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Evaluation PCB
MIXERS - HIGH IP3 - SMT
9
List of Materials for Evaluation PCB 101830 [1]
Item
Description
J1 - J3
PCB Mount SMA RF Connector
U1
HMC402MS8 / HMC402MS8E Mixer
PCB [2]
101828 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
9 - 252
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC402MS8 / 402MS8E
v02.0705
HIGH IP3 GaAs MMIC
MIXER, 1.8 - 2.2 GHz
Notes:
MIXERS - HIGH IP3 - SMT
9
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9 - 253