SS22S THRU SS220S 2.0A Surface Mount Schottky Barrier Rectifier - 20 ~ 200 V SOD-123S Package Features SOD-123S · The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 · Metal silicon junction,majority carrier conduction · Low power loss,high efficiency · High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds,0.375"(9.5mm) lead length, 5 lbs. (2.3kg) tension Mechanical Data · Terminal: : olderable per MIL-STD-750,Method 2026 · Case: : JEDEC SOD-123S molded plastic body · Polarity: : Color band denotes cathode end · Mounting Position:Any Maximum Ratings and Electrical Characteristics @TA=25℃ unless otherwise specified Single Phase,half wave,60Hz,resistive or inductive load.For capacitive load,derate current by 20%. Symbol SS22S D22/ M2 SS24S 24R/ M4 Maximum repetitive peak reverse voltage VRRM 20 40 Maximum RMS voltage VRMS 14 Maximum DC blocking voltage VDC 20 Parameter Maximum Average forward output rectified current (Fig.1) SS26S 26/ M6 SS210S D210/ M10 SS215S D215 SS220S D220 60 100 150 200 V 28 42 70 105 140 V 40 60 100 150 200 V UNIT I(AV) 2.0 A Peak forward surge current 8.3ms single sine-wave superimposed on rated load(JEDEC Method) IFSM 40 A Maximum instantaneous forward voltage @2.0A VF Maximum DC reverse current at TA=25℃ rated DC blocking voltage per leg TA=100℃ IR 0.7 0.85 CJ Operating junction temperature range TJ mA 5 220 pF 80 -55 to +125 TSTG V 0.2 0.5 10 Typical junction capacitance (NOTE 1) storage temperature range 0.55 ℃ -55 to +150 ℃ -55 to +150 Note:1.Measured at 1MHZ and applied reverse voltage of 4.0V D.C. Note:1.Measured at 1MHZ and applied reverse voltage of 4.0V D.C. 2014.10 www.willas.com.tw Rev.F02 P1 SS22S THRU SS220S 2.0 1.6 Single Phase Half Wave 60Hz Resistive or inductive Load 1.2 0.8 SS22S-SS26S SS210S-SS220S 0.4 0 0 25 50 75 100 125 150 175 PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 40 32 24 16 8 0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 AMBIENT TEMPERATURE, C FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 1 TJ=25 C PULSE WIDTH=300 µs 1%DUTY CYCLE SS22S-SS24S SS26S SS210S-SS220S 0.1 0.01 0.2 0.4 0.6 0.8 1.0 10 100 NUMBER OF CYCLES AT 60 Hz FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MILLAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 2.0A Surface Mount Schottky Barrier Rectifier - 20 ~ 200 V SOD-123S Package 1.1 100 10 TJ=100 C 1 TJ=75 C 0.1 TJ=25 C 0.01 0.001 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF PEAK REVERSE VOLTAGE,% JUNCTION CAPACITANCE, pF FIG. 5-TYPICAL JUNCTION CAPACITANCE 2000 1000 SS22S-SS24S SS26S-SS220S 100 TJ=25 C 10 0.1 1.0 10 100 REVERSE VOLTAGE,VOLTS 2014.10 www.willas.com.tw Rev.F02 P2 SS22S THRU SS220S 2.0A Surface Mount Schottky Barrier Rectifier - 20 ~ 200 V SOD-123S Package .009(0.22) .004(0.10) .029(0.75) .053(1.35) .119(3.00) .099(2.51) SOD-123S .079(2.00) .054(1.38) Outline Drawing .052(1.33) .032(0.81) .153(3.90) .137(3.50) .033(0.85) .010(0.25) Dimensions in inches and (millimeters) Rev.E 2014.10 www.willas.com.tw Rev.F02 P3 SS22S THRU SS220S 2.0A Surface Mount Schottky Barrier Rectifier - 20 ~ 200 V SOD-123S Package Suggested Soldering Pad Layout SOD-123S . 0 9 1 ( 2 . 31 ) .045 ( 1 . 3 8 ) .038(0.97) Dimensions in inches and (millimeters) 2014.10 www.willas.com.tw RevA Rev.F02 P4 2.0A Surface Mount Schottky Barrier Rectifier - 20 ~ 200 V SOD-123S Package SS22S THRU SS220S Ordering Information: Device PN Part Number -T(1) G (2)-WS Note: (1) Packing code, Tape & Reel Packing Packing Tape&Reel: 3 Kpcs/Reel (2) RoHS product for packing code suffix ”G”；Halogen free product for packing code suffix “H” ***Disclaimer*** WILLAS reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. WILLAS or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on WILLAS data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. WILLAS does not assume any liability arising out of the application or use of any product or circuit. WILLAS products are not designed, intended or authorized for use in medical, life‐saving implant or other applications intended for life‐sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of WILLAS. Customers using or selling WILLAS components for use in such applications do so at their own risk and shall agree to fully indemnify WILLAS Inc and its subsidiaries harmless against all claims, damages and expenditures. 2014.10 www.willas.com.tw Rev.F02 P5