Optoelectronics PDF(2.6MB)

OPTO
■ Photocoupler
PHOTOCOUPLER LINEUP
Lineup
<Phototransistor output type>
Output type
Single phototransistor
Features
Model No. (series)
General purpose,
High collector-emitter voltage
Low input current
AC input response
Darlington phototransistor
High sensitivity,
High collector-emitter voltage
Low input current
Low input current
Compact, Half pitch
(lead space), SMT type
Single phototransistor
General purpose,
High resistance to noise, etc.
Single phototransistor
34
PC364NJ0000F
34
PC355NJ0000F / PC452J00000F
34
PC365NJ0000F
34
35
Low input current
PC3H71xNIP0F
35
PC3H3J00000F / PC3H4J00000F
35
PC3H41xNIP0F
35
PC3H5J00000F
35
PC3H510NIP0F
35
Reinforced insulation
PC123XNNSZ0F
36
Low input current
General purpose,
High collector-emitter voltage, etc.
PC1231xNSZ0X
36
PC817XNNSZ0F / PC851XNNSZ0F
36
High sensitivity
Low input current
DIP type (6-pin)
34
PC354NJ0000F
35
Low input current
(4-pin, DIP type)
34
PC367NJ0000F
PC3H7J00000F
Low input current
DIP type (4-pin)
PC357NJ0000F / PC451J00000F
Reinforced insulation PC3HU7xYIP0B
AC input response
Darlington phototransistor
Page
PC8171xNSZ0X
36
Darlington phototransistor
High sensitivity,
High collector-emitter voltage
PC815XNNSZ0F / PC852XNNSZ0F
36
Single phototransistor
General purpose,
High collector-emitter voltage, etc.
PC7xxV0NSZXF▲
37
Darlington phototransistor
High sensitivity,
High collector-emitter voltage, etc.
PC7x5V0NSZXF▲
37
<OPIC output type>
Package type
Compact, SMT type
DIP type, SMT type
Output type
Features
Model No. (series)
Optoelectronics
Package type
Mini-flat 4-pin
Compact, SMT type
Page
Digital output
General purpose, High response speed
PC400J00000F
38
Analog/Digital output
High CMR
PC457L0NIP0F
38
Digital output
General purpose
PC900V0NSZXF
39
Built-in base amplifier
For inverter control
PC925LENSZ0F
39
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
33
OPTO
PHOTOCOUPLERS
■ Photocouplers
♦Phototransistor
Darlington phototransistor output
Single phototransistor output
Output type
Output Type
<Compact, SMT type>
Model No.
Internal
connection
diagram
○: Approved
Approved
by safety
standards*2
Features
UL
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Isolation
Current transfer ratio
Response time
CollectorForward voltage
emitter
Package current (AC)
tr
voltage CTR
RL VCE
IC
IF VCE
Viso
IF
(µs)
(%)
VCEO
(mA)
(V)
(mA) (Ω) (V)
(mA)
(rms)
TYP.
MIN.
(V)
(kV)
PC357NJ0000F
General purpose
○
50
3.75
80
50
5
5
4
2
100
2
PC451J00000F
High collector-emitter
voltage
○
50
3.75
350
40
5
5
4
2
100
2
PC367NJ0000F
Low input current,
high resistance to noise*1
○
10
3.75
80
100
0.5
5
4
2
100
2
PC354NJ0000F
AC input response
○
±50
3.75
80
20
±1
5
4
2
100
2
±10
3.75
80
50
±0.5
5
4
2
100
2
Mini-flat
4-pin
PC364NJ0000F
Low input current,
AC input response,
high resistance to noise*1
○
PC355NJ0000F
High sensitivity
○
50
3.75
35
600
1
2
60
2
100
2
PC365NJ0000F
High sensitivity,
low input current
○
10
3.75
35
600
0.5
2
60
10
100
2
PC452J00000F
High collector-emitter
voltage
○
50
3.75
350
1 000
1
2
100
20
100
2
*1 CMR: MIN. 10 kV/µs
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
PC357NJ0000F
(Mini-flat 4-pin)
34
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOCOUPLERS
♦ Phototransistor
*1
*2
*3
*4
*5
*6
Model No.
Internal
connection
diagram
Features
○: Approved
Approved
by safety
standards*3
UL
PC3HU7xYIP0B
Reinforced insulation
(internal insulation distance:
MIN. 0.4 mm),
low-profile package
PC3H7J00000F
Standard
PC3H71xNIP0F
○ *4, 5
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Isolation
Current transfer
CollectorResponse time
Forward voltage
ratio
emitter
Package current (AC)
voltage CTR
tr
IF
Viso
IF VCE
IC RL VCE
VCEO
(%)
(µs)
(mA)
(rms)
(mA)
(V)
(mA) (Ω) (V)
(V)
MIN.
TYP.
(kV)
Lowprofile
50
3.75
80
50
5
5
4
2 100 2
mini-flat
4-pin
○ *6
50
2.5
80
20
1
5
4
2
100
2
High resistance to noise*1,
low input current
○
10
2.5
80
100
0.5
5
4
2
100
2
PC3H3J00000F
AC input response,
high resistance to noise*1
○
±50
2.5
80
20
±1
5
4
2
100
2
PC3H4J00000F
AC input response
○ *2, 6
±50
2.5
80
20
±1
5
4
2
100
2
PC3H41xNIP0F
AC input response,
high resistance to noise*1,
low input current
○
±10
2.5
80
50
±0.5
5
4
2
100
2
PC3H5J00000F
High sensitivity
○
50
2.5
35
600
1
2
60
2
100
2
10
2.5
35
600
0.5
2
60
2
100
2
PC3H510NIP0F
High sensitivity,
low input current
Mini-flat
4-pin
Mini-flat
4-pin
○
CMR: MIN.10 kV/µs
A VDE approved type is optionally available.
Please refer to Specification Sheets for model numbers approved by safety standards.
VDE, CSA approved
In conformance with BSI, SEMKO, DEMKO, NEMKO, and FIMKO
UL, cUL approved
PC3HU7xYIP0B
Optoelectronics
Darlington phototransistor output
Single phototransistor output
Output type
Output Type
<Compact, half pitch (lead space) SMT type>
PC3H7J00000F
(Mini-flat 4-pin)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
35
OPTO
PHOTOCOUPLERS
♦ Phototransistor
Darlington phototransistor output
Single phototransistor output
Output type
Output Type
<DIP type (4-pin)>
Model No.
Internal
connection
diagram
○: Approved
(Ta = 25°C)
Absolute maximum ratings
Isolation CollectorForward
Package current voltage emitter
(AC)
voltage
Others
IF
UL VDE
Viso (rms) VCEO
*2
*3
(mA)
(V)
(kV)
Approved by
safety standards*8
Features
Electro-optical characteristics
Current transfer ratio Response time
CTR
(%)
MIN.
IF
(mA)
tr
RL
(µs) (Ω)
TYP.
PC123XNNSZ0F*1, *5, *6, *7
High isolation voltage,
reinforced insulation
○
○
○
50
5.0
70
50
5
4
100
PC1231xNSZ0X*1
High isolation voltage, reinforced
insulation, low input current,
high resistance to noise*4
○
○
○
10
5.0
70
50
0.5
4
100
PC817XNNSZ0F*5, *6, *7
High isolation voltage
○
–
○ *9
50
5.0
80
50
5
4
100
PC8171xNSZ0X*5, *6
High isolation voltage, low input
current, high resistance to noise*4 ○
–
–
10
5.0
80
100
0.5
4
100
PC851XNNSZ0F*5, *6
High isolation voltage,
high collector-emitter voltage
○
–
–
50
5.0
350
40
5
4
100
PC815XNNSZ0F*5, *6
High isolation voltage,
high sensitivity
○
–
–
50
5.0
35
600
1
60
100
PC852XNNSZ0F*5, *6
High isolation voltage,
high collector-emitter voltage
○
○
–
50
5.0
350
1 000
1
100 100
4-pin
DIP
*1
*2
*3
*4
*5
*6
*7
Wide lead spacing type is also available. Creepage distance: 6.4 mm or more, wide lead spacing type: 8 mm or more.
Optionally available.
BSI, SEMKO, DEMKO, NEMKO, FIMKO, CSA
CMR: 10 kV/µs MIN.
Lead forming type is also available for surface mounting.
Taped package of lead forming type for surface mounting is also available.
Wide lead spacing type is also available. Compatible with wide lead spacing type lead-forming models for surface-mount use. Also compatible with taped packages for wide
lead spacing type lead-forming models for surface-mount use.
*8 Please refer to Specification Sheets for model numbers approved by safety standards.
*9 UL, CSA approved
PC817XNNSZ0F
(4-pin DIP)
36
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOCOUPLERS
♦ Phototransistor
Output type
PC713V0NSZXF▲
Internal
connection
diagram
○: Approved
Features
High isolation voltage,
with base terminal
Approved
by safety
standards*2
UL
VDE*1
○
○
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Isolation Collector- Current transfer Response
Forward
ratio
time
Package current voltage emitter
(AC)
voltage CTR
tr
IF
RL
IF
Viso (rms) VCEO
(%)
(mA) (µs)
(Ω)
(mA)
(V)
(kV)
MIN.
TYP.
50
5.0
80
50
5
4
100
6-pin
DIP
PC715V0NSZXF▲
High isolation voltage,
high sensitivity
○
○
50
5.0
35
600
1
60
100
PC725V0NSZXF▲
High isolation voltage,
high sensitivity,
high collector-emitter voltage,
high power
○
○
50
5.0
300
1 000
1
100
100
*1 Optionally available.
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Optoelectronics
Darlington phototransistor output
Model No.
Single phototransistor output
Output Type
<DIP type (6-pin)>
37
OPTO
PHOTOCOUPLERS
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Output ( light-detecting element and signal-processing circuit integrated onto a single chip. )
○: Approved
<Compact, SMT type> (1-1)
♦OPIC
Model No.
PC400J00000F
Internal
connection
diagram
A
(Ta = 25°C)
Absolute maximum
Electro-optical characteristics*1
ratings
Isolation
Low level output voltage
Threshold input current
Package Forward voltage
current
V
OL
IFHL
IFLH
(AC)
IF
RL
Ta
IOL
IF
(mA) (mA)
UL VDE*3
Viso (rms) (V)
(mA)
(Ω)
(mA)
(°C)
(mA)
MAX.
MAX.
MAX.
(kV)
Approved by
safety
standards*2
Features
Digital output,
normal-off operation
○
–
Mini-flat
5-pin
50
3.75
0.4
0 to +70
16
4
2.0
–
280
A: Rated voltage circuit
*1 Each item is measured at Vcc=5V. (PC400)
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
*3 Optionally available.
<Compact, SMT type> (1-2)
Model No.
PC457L0NIP0F
Internal
connection
diagram
○: Approved
Approved by
safety
standards*1
Features
High speed (1 Mb/s),
high CMR (15 kV/µs),
for flow soldering
UL
VDE*2
○
○
(Ta = 25°C)
Absolute maximum
Electro-optical characteristics
ratings
Isolation
Current transfer ratio
Propagation delay time
Package Forward voltage
current
CTR
tPHL tPLH
(AC)
VO VCC
IF
IF
RL
IF
Viso (rms) (%) (mA) (V) (V) (µs) (µs)
(Ω) (mA)
(mA)
MIN.
TYP. TYP.
(kV)
Mini-flat
5-pin
25
3.75
19
16
0.4
4.5
0.2
0.4
1 900
16
*1 Please refer to Specification Sheets for model numbers approved by safety standards.
*2 Optionally available.
PC400J00000F
(Mini-flat 5-pin)
38
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOCOUPLERS
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Output ( light-detecting element and signal-processing circuit integrated onto a single chip. )
○: Approved
<DIP type, digital output>
♦OPIC
Model No.
Internal
connection
diagram
Features
PC900V0NSZXF*2, *3
Digital output,
normal-off operation
A
Absolute
maximum ratings
Approved by
safety
standards*5
UL
○
(Ta = 25°C)
Electro-optical characteristics*1
Threshold input
Isolation
Low level output voltage
Package Forward voltage
current
current
(AC)
VOL
IFHL IFLH
F
I
IF
RL
Ta
IOL
VDE
Viso (rms) (V)
(mA) (mA)
*4
(mA)
(mA) (mA)
(Ω)
(°C)
(kV)
MAX.
MAX. MAX.
○
6-pin
DIP
50
5.0
0.4
0 to +70
16
4
2.0
–
280
A: Rated voltage circuit
*1 Each item is measured at Vcc=5V.
*2 Lead forming type is also available for surface mounting.
*3 Taped package of lead forming type for surface mounting is also available.
*4 Optionally available.
*5 Please refer to Specification Sheets for model numbers approved by safety standards.
PC900V0NSZXF
(6-pin DIP)
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Output ( light-detecting element and signal-processing circuit integrated onto a single chip. )
○: Approved
<DIP type, Gate drive type>
Model No.
Internal
connection
diagram
PD
Interface
OPIC
PC925LENSZ0F*1
Tr1
Tr2
Features
• Built-in drive circuit
directly connectable to
MOS-FET and IGBT
• Peak output current: 2.5 A
• Low dissipation current
(Icc = TYP. 2.5 mA)
• High resistance to noise
(CMR: MIN. 15 kV/µs)
Approved by
safety
standards*3
UL
VDE
○
○
Package
*2
8-pin
DIP
(Ta = 25°C)
Absolute
Electro-optical characteristics
maximum ratings
Isolation
Propagation delay time
Forward
voltage
current
tPHL tPLH
(AC)
IF
RL1
RL2
VCC
IF
Viso (rms) (µs) (µs)
(V) (mA) (Ω)
(Ω)
(mA)
TYP. TYP.
(kV)
25
5.0
MAX. MAX. 15 to
0.5
0.5
30
7 to
16
RG =
10
Optoelectronics
♦OPIC
–
*1 Lead forming type is also available for surface mounting. Taped package of lead forming type for surface mounting is also available.
*2 A VDE approved type is optionally available.
*3 Please refer to Specification Sheets for model numbers approved by safety standards.
PC925LENSZ0F
(8-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
39
OPTO
■ Phototriac
Package
Mini-flat (SMD)
PHOTOTRIAC COUPLER LINEUP
Coupler Lineup
Applied voltage
AC 200 V lines
(VDRM = 600V)
ON-state
current (rms)
0.05 A
Features
Model No.
S2S3A00F*3 / S2S5A00F*3 / S2S5FA0F*3
General purpose
Built-in zero-cross circuit S2S4A00F*3
DIP type
(4-pin)
DIP type
(6-pin package,
5th-pin cut)
AC 200 V lines
(VDRM = 600V)
0.1 A
41
42
General purpose
PC3ST11NSZKF
41
Reinforced isolation
PC3SH11YFZAX*3 / PC3SH13YFZAX*3
41
Built-in zero-cross circuit PC3SH21YFZBX*2
42
AC 100 V lines
(VDRM = 400V)
0.1 A
General purpose
PC2SD11NTZAF*3
41
AC 200 V lines
(VDRM = 600V)
0.1 A
General purpose
PC3SD12NTZAF*3 / PC3SD11YTZCF*1 /
PC3SD11NTZCF*1 / PC3SD13YXZBF*2
41
PC3SD21NTZAF*3 / PC3SD21NTZBF*2 /
Built-in zero-cross circuit PC3SD21NTZDF*4
42
PC3SF11YVZAF*3 / PC3SF11YVZBF*2
41
Built-in zero-cross circuit PC3SF21YVZAF*3 / PC3SF21YVZBF*2
42
Reinforced isolation
AC 200 V lines
(VDRM = 800V)
0.1 A
PC4SD11NTZCF*1
General purpose
Built-in zero-cross circuit PC4SD21NTZCF*1 / PC4SD21NTZDF*4
Reinforced isolation
PC4SF11YTZBF*2
Built-in zero-cross circuit PC4SF21YVZBF*2 / PC4SF21YWPSF*2
Minimum trigger current: *1 IFT ≦ 5 mA, *2 IFT ≦ 7 mA, *3 IFT ≦ 10 mA, *4 IFT ≦ 3 mA
40
Page
41
42
41
42
OPTO
■ Phototriac
PHOTOTRIAC COUPLERS
Couplers
○: Approved
(Ta = 25°C)
Approved by
safety standards*4
Internal
connection
diagram
Features
UL,
CSA
S2S3A00F
200 V lines, compact
○
○ *6
–
S2S5A00F
200 V lines, compact
○
○ *6
–
S2S5FA0F
High impulse noise product
○
○ *6
–
200 V lines, compact
○
○ *6
–
200 V lines, compact,
reinforced isolation
200 V lines, compact,
reinforced isolation,
high noise resistance
○
○
○ *2
○
○
○ *2
PC2SD11NTZAF
100 V lines
○
–
–
PC3SD12NTZAF
200 V lines
○
○ *6
–
PC3SD13YXZBF
High impulse noise product
○
○ *6
–
PC3SD11YTZCF
200 V lines
○
○ *6
–
PC3ST11NSZKF
PC3SH11YFZAX
PC3SH13YFZAX
PC3SD11NTZCF
200 V lines
○
○ *6
–
PC4SD11NTZCF
200 V lines,
repetitive peak-OFF-state voltage
○
○ *6
–
PC3SF11YVZAF
200 V lines, reinforced isolation
○
○
○ *2
PC3SF11YVZBF
200 V lines, reinforced isolation
○
○
○ *2
PC4SF11YTZBF
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
○
○
○ *2
10
Mini-flat
4-pin
0.05
3.75
10
10
600
4-pin
DIP
0.1
10
5.0
10
10
400
10
10
7
600
5
6-pin
DIP*1, 3
0.1
600
800
5.0
5
5
10
600
7
800
7
Optoelectronics
Model No.
Electro-optical
Absolute maximum ratings
characteristics
Repetitive
Min. trigger
Isolation
peak
current
Package ON-state
voltage
current OFF-state
IFT
VDE Others
(AC)
(mA) MAX.
voltage
IT (rms)
Viso (rms)
(A)
VD = 6 V,
VDRM
(kV)
(V)
RL = 100Ω
For the notes *1 to *6, see next page.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
41
OPTO
■
PHOTOTRIAC COUPLERS
Phototriac Couplers
(Built-in zero-cross circuit type)
○: Approved
(Ta = 25°C)
Approved by
safety standards*4
Model No.
S2S4A00F
Internal
connection diagram
Zero-cross circuit
PC3SH21YFZBX
PC3SD21NTZAF
PC3SD21NTZBF
PC3SD21NTZDF
PC4SD21NTZCF
PC4SD21NTZDF
PC3SF21YVZAF
200 V lines, compact
○
200 V lines, compact,
reinforced isolation
○
○
○ *2
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
repetitive peak-OFF-state voltage
200 V lines,
repetitive peak-OFF-state voltage
○
○ *6
–
○
○ *6
–
○
○ *6
–
○
○ *6
–
○
○ *6
–
200 V lines, reinforced isolation
○
○
○ *2
200 V lines, reinforced isolation
○
○
○ *2
PC4SF21YVZBF
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
○
○
○ *2
High impulse noise product
○
○
○ *2
4-pin
DIP
0.1
600
5.0
7
10
600
7
3
6-pin
DIP*1, 3
5
800
0.1
5.0
3
10
600
7
7
6-pin
DIP*3
800
7
Lead forming type for surface mounting is also available.
In conformance with BSI, SEMKO, DEMKO, and FIMKO
These are molded pin No. 5.
Please refer to Specification Sheets for model numbers approved by safety standards.
VD = 6 V, RL = 100Ω
Optionally available
S2S3A00F
(Mini-flat 4-pin)
42
UL,
CSA
PC3SF21YVZBF
PC4SF21YWPSF
*1
*2
*3
*4
*5
*6
Zero-cross circuit
Features
Electro-optical
Absolute maximum ratings
characteristics
Min. trigger
Repetitive Isolation
current
Package ON-state
voltage
peak
current
IFT
(AC)
VDE Others
OFF-state
(mA) MAX.
IT (rms)
VDRM Viso (rms)
(A)
VD = 4 V,
(V)
(kV)
RL = 100Ω
Mini-flat
–
0.05
600
3.75
10*5
○ *6
4-pin
PC3ST series
(4-pin DIP)
PC3SH series
(4-pin DIP)
PC2SD11NTZAF
⎧PC3SD series,⎫
⎜PC4SD series ⎜
⎭
⎩
(6-pin DIP)
PC3SF series
(PC4SF series)
(6-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
Solid State Relay Lineup
Package
DIP 6-pin
DIP 8-pin
Applied voltage
ON-state current
(rms)
Features
Model No.
Page
AC 100 V lines
0.15 A
General purpose
PR22MA11NTZF
44
AC 200 V lines
0.06 A
General purpose
PR31MA11NTZF
44
0.15 A
General purpose
PR32MA11NTZF
44
0.3/0.6/0.9/1.2 A
General purpose
PR33MF5 series / PR39MF5 series /
PR36MF5 series / PR3BMF5 series /
PR36MF12NSZF
44
0.6/0.9/1.2 A
Built-in zero-cross circuit
PR36MF2 series / PR39MF2 series
44
AC 200 V lines
Optoelectronics
■
SOLID STATE RELAY LINEUP
43
OPTO
■ Solid
SOLID STATE RELAYS
State Relays
<DIP type>
○: Approved
Approved by
safety standards*1
Model No.
Internal
connection
diagram
Features
UL
CSA VDE*2
PR22MA11NTZF
100 V lines,
150 mA model in a small package
○
○
○
PR31MA11NTZF
200 V lines, compact
○
○
○
PR32MA11NTZF
200 V lines,
150 mA model in a small package
○
○
○
PR33MF51NSLF
200 V lines, compact
○
○
○
200 V lines, compact
○
○
○
PR36MF51NSLF
200 V lines, compact
○
○
○
PR36MF12NSZF
200 V lines, compact,
low input current
○
○
○
PR39MF51NSLF
200 V lines, compact
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
PR33MF52NSLF
PR3BMF51NSLF
200 V lines, compact
PR3BMF52NSZF
PR36MF21NSZF
PR36MF22NSZF
PR39MF22NSZF
Zerocross
circuit
200 V lines, compact,
low input current
200 V lines, compact (built-in zerocross circuit)
200 V lines, compact (built-in zerocross circuit), low input current
200 V lines, compact (built-in zerocross circuit), low input current
(Ta = 25°C)
Electrical
Absolute maximum ratings
characteristics
Min. trigger
Repetitive Isolation
current
Package ON-state
voltage
peak
current
IFT
(AC)
OFF-state
(mA) MAX.
IT (rms)
voltage Viso (rms)
(A)
VD = 6 V,
(kV)
VDRM (V)
RL = 100Ω
0.15
6-pin
DIP
400
10
5.0
0.06
10
600
0.15
10
10
0.3
10
10
0.6
5
600
8-pin
DIP
0.9
10
4.0
10
1.2
5
10
0.6
600
0.9
5
5
*1 Please refer to Specification Sheets for model numbers approved by safety standards.
*2 Optionally available.
PR22MA11NTZF
(6-pin DIP)
44
PR26MF21NSZF
(8-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOINTERRUPTER LINEUP
★ Under
■
development
Photointerrupter Lineup
<Transmissive type>
Output type
Single phototransistor
Package type
Outline
Compact
PWB mounting type
High response speed
Surface-mount type
Model No. (series)
GP1S396HCP0F
/ GP1S09xHCZ0F /
GP1S19xHCZ0F
GP1S396HCPSF
/ GP1S296HCPSF / GP1S092HCPIF / GP1S19xHCxSF
PWB mounting type
GP1S5x
Horizontal slit
PWB mounting type
GP1S59J0000F
With connector
General purpose
Snap-in
GP1S173LCS2F
Compact
High resolution
PWB mounting type
★GP1A396HCP0F
Surface-mount type
★GP1A396HCPSF
High voltage
PWB mounting type
Case type
Digital output
Mounting method
(OPIC output)
Case type
Wide gap
With connector
General purpose
series
Page
46
46
47
47
/ GP1S273LCS1F
47
48
48
GP1A98HCZ0F▲
Surface-mount type
GP1A98HCPSF▲
48
PWB mounting type
GP1A5x
48
PWB mounting type
GP1A57HRJ00F
Snap-in
series
/ GP1A173LCS2F▲ / GP1A173LCSVF / GP1A273LCS1F▲
GP1A173LCS3F
48
48
49
<Reflective type>
Package type
Outline
Mounting method
Model No. (series)
Page
Leadless
Long focal distance
Surface-mount type
GP2S700HCP
49
High response speed
Compact,
thin (leadless)
General purpose
Surface-mount type
GP2S60
49
OPIC output
With connector
Light modulation type,
Sensitivity adjusted
Screw mounting type/
Compact snap-in/
Inverter light countermeasures
GP2A25 series / GP2A28 series /
GP2A200LCS0F / GP2A230LRS0F /
GP2A230LRSAF / ★GP2A430LCSAF /
GP2A240LCS0F / GP2A250LCS0F
50
<Application-specific photointerrupter lineup>
Detection type
Transmissive type
Outline (Output type etc.)
For amusement use
Mounting method
Screw mounting type
Model No. (series)
GP1A204HCS0▲
Page
51
Optoelectronics
Output type
Single phototransistor
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
45
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
■ Photointerrupters
<Transmissive type>
♦Single Phototransistor Output
<Compact type>
Model No.
Internal
connection
diagram
(Ta = 25°C)
Electro-optical
characteristics
Detecting
Current transfer ratio
Response time
and
Slit width
emitting
tr
CTR
(mm)
F
V
CE
RL VCE
IC
I
gap
(µs)
(%)
(mA) (V)
(mA) (kΩ) (V)
(mm)
TYP.
MIN.
Features
GP1S092HCPIF
Wide gap, for soldering reflow,
surface mount compatible, with positioning boss
(4.5 × 2.6 × 2.9 [height] mm)
2.0
0.3
2.0
5
5
50
0.1
1
5
GP1S093HCZ0F
Wide gap (4.5 × 2.6 × 2.9 [height] mm)
2.0
0.3
2.0
5
5
50
0.1
1
5
3.0
0.3
0.8
5
5
50
0.1
1
5
1.7
0.3
3.0
5
5
50
0.1
1
5
1.5
0.3
3.0
5
5
50
0.1
1
5
1.1
0.3
2.0
5
5
50
0.1
1
5
1.1
0.3
2.0
5
5
50
0.1
1
5
1.0
0.2
3.0
5
5
50
0.1
1
5
1.2
0.12
2.0
5
5
30
0.1
1
5
1.2
0.12
2.0
5
5
30
0.1
1
5
2.0
0.3
2.0
5
5
50
0.1
1
5
GP1S195HCZSF
GP1S195HCPSF
Wide gap, with positioning pin,
(5.5 × 2.6 × 4.8 [height] mm)
Compact, wide gap,
size: 3.6 × 2.0 × 2.7 (height) mm
Compact, wide gap, surface mount compatible,
size: 3.4 × 2.0 × 2.7 (height) mm
GP1S196HCZ0F
Compact, low profile (3.1 × 2.0 × 2.7 [height] mm)
GP1S196HCZSF
GP1S196HCPSF
Surface mount, for soldering reflow,
compact, low profile (3.1 × 2.0 × 2.7 [height] mm)
Surface mount, for soldering reflow,
compact, low profile (2.5 × 1.8 × 1.9 [height] mm)
Straight lead type,
compact, low profile (2.26 × 1.4 × 1.6 [height] mm)
Surface mount, for soldering reflow,
compact, low profile (2.26 × 1.4 × 1.6 [height] mm)
High resolution, wide gap,
with mounting hole (4.5 × 2.6 × 4.5 [height] mm)
GP1S094HCZ0F
GP1S194HCZ0F
GP1S296HCPSF
GP1S396HCP0F
GP1S396HCPSF
GP1S097HCZ0F
※ Topr: –25 to +85°C
※※ GP1SxxxHCZxF: Sleeve package, GP1SxxxHCPxF: Taped package
46
GP1S092HCPIF
GP1S093HCZ0F
GP1S094HCZ0F
GP1S194HCZ0F
GP1S195HCPSF/
GP1S195HCZSF
GP1S196HCZSF/
GP1S196HCPSF
GP1S296HCPSF
GP1S396HCPSF
GP1S396HCP0F
GP1S097HCZ0F
GP1S196HCZ0F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
<Case type>
Model No.
(Ta = 25°C)
Internal
connection
diagram
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
F
V
CE
RL VCE
IC
I
gap
(µs)
(%)
(mA) (V)
(mA) (Ω) (V)
(mm)
TYP.
MIN.
Features
GP1S50J0000F
High resolution, both-side mounting type
3.0
0.5
2.5
20
5
3
2
100
2
GP1S51VJ000F
High resolution, side mounting type
3.0
0.5
2.5
20
5
3
2
100
2
GP1S52VJ000F
High resolution, PWB mounting type
3.0
0.5
2.5
20
5
3
2
100
2
GP1S53VJ000F
High resolution, PWB mounting type
5.0
0.5
2.5
20
5
3
2
100
2
2.0
0.15
2.0
20
5
38
0.5
1 000
2
5.0
0.5
2.5
20
5
3
2
100
2
4.2
0.5
2.5
20
5
3
2
100
2
High resolution, with positioning pin,
PWB mounting type
High resolution, with positioning pin,
PWB mounting type
High resolution, horizontal slit, with positioning pin,
PWB mounting type
GP1S56TJ000F
GP1S58VJ000F
GP1S59J0000F
※ Topr: –25 to +85°C
GP1S56TJ000F
GP1S51VJ000F
GP1S52VJ000F
GP1S58VJ000F
GP1S53VJ000F
GP1S59J0000F
<With connector>
Model No.
Internal
connection
diagram
(Ta = 25°C)
Optoelectronics
GP1S50J0000F
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
VCE
RL VCE
IC
IF
gap
(µs)
(%)
(mA) (V)
(mA) (Ω) (V)
(mm)
TYP.
MIN.
Features
GP1S173LCS2F
Snap-in mounting integrated connector type
Applicable to 3 kinds of thickness of mounting boards
5.0
0.5
2.5
20
5
3
2
100
2
GP1S273LCS1F
Snap-in mounting integrated connector type
Applicable to 3 kinds of thickness of mounting boards
Compact (Compatible with 1.5 mm pitch connector)
5.0
0.7
2.5
20
5
3
2
100
2
※ Topr: –25 to +85°C, –30 to +95°C (GP1S173LCS2F, GP1S273LCS1F)
GP1S173LCS2F
GP1S273LCS1F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
47
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
★ Under
development
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Type ( light-detecting element and signal-processing circuit integrated onto a single chip. )
<Compact type>
♦OPIC
Internal
connection
diagram
Model No.
(Ta = 25°C)
Electro-optical characteristics
Detecting
and
Threshold input current
Propagation delay time
Slit width
emitting
tPLH
IFHL
tPHL
IFLH
(mm)
VCC
RL
RL
VCC
IF
gap
(mA) (mA)
(µs)
(µs)
(kΩ)
(V)
(mA) (kΩ)
(V)
(mm)
MAX. MAX.
TYP. TYP.
Features
Compact, high response
speed, digital output, PWB
mounting
Compact, high response
speed, digital output,
surface mount
★ GP1A396HCP0F
★ GP1A396HCPSF
Voltage
regulator
Amplifier
GP1A98HCZ0F▲
GP1A98HCPSF▲
1.2
0.12
2.85
–
2.5 to
5.5
24 to
30
15
15
5
24
3.3
1.2
0.12
2.85
–
2.5 to
5.5
24 to
30
15
15
5
24
3.3
Compact, PWB mounting
3.2
0.5
8
–
3.3 to 3.9 to
24
20
2.0
10.0
10
3.9 to 3.3 to
20
24
Compact, surface mount
3.2
0.5
8
–
3.3 to 3.9 to
24
20
2.0
10.0
10
3.9 to 3.3 to
20
24
※ Topr = –25 to +85°C
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
GP1A396HCP0F
GP1A396HCPSF
GP1A98HCPSF
GP1A98HCZ0F
<Case type>
(Ta = 25°C)
Internal
connection
diagram
Model No.
Features
GP1A50HRJ00F
GP1A51HRJ00F
Voltage
regulator
Amplifier
GP1A52HRJ00F
GP1A53HRJ00F
GP1A57HRJ00F
Detecting
and
Slit width
emitting
(mm)
gap
(mm)
(When light is cut off:
low level)
VCC
(V)
Both-side mounting,
with screw hole
3.0
0.5
5
–
5
3
5
5
280
5
Side mounting, with screw hole
3.0
0.5
5
–
5
3
5
5
280
5
PWB mounting type
3.0
0.5
5
–
5
3
5
5
280
5
PWB mounting type
5.0
0.5
8
–
5
3
5
8
280
5
10.0
1.8
7
–
5
3
5
7
280
5
5.0
0.5
8
–
5
3
5
8
280
5
3.0
0.5
–
5
5
5
3
5
280
5
PWB mounting type,
with positioning pin
PWB mounting type,
with positioning pin
GP1A58HRJ00F
Electro-optical characteristics
Threshold input current
Propagation delay time
tPLH
IFHL
tPHL
IFLH
RL
VCC
IF
(mA)
(mA)
(µs)
(µs)
(V)
(mA) (Ω)
MAX.
MAX.
TYP.
TYP.
Voltage
regulator
Amplifier
PWB mounting type
GP1A52LRJ00F
(When light is cut off:
high level)
※ Topr = –25 to +85°C
GP1A50HRJ00F
48
GP1A51HRJ00F
GP1A52LRJ00F
(GP1A52HRJ00F)
GP1A53HRJ00F
⎧GP1A58HRJ00F ⎫
⎜with positioning pin⎜
⎩
⎭
GP1A57HRJ00F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PHOTOINTERRUPTERS
(TRANSMISSIVE TYPE)/(REFLECTIVE TYPE)
OPTO
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Type ( light-detecting element and signal-processing circuit integrated onto a single chip. )
<With 3-pin connector terminal>
♦OPIC
Model No.
Internal
connection
diagram
Features
GP1A173LCS2F▲
Voltage
regulator
Amplifier
GP1A173LCSVF
GP1A273LCS1F▲
with 3-pin connector
GP1A173LCS3F
3 V operation,
snap-in mounting integrated
connector type*1
Snap-in mounting integrated
connector type*1
Snap-in mounting integrated
connector type*1,
enforced electrostatic discharge
(ESD) type
Integrated connector, compatible
with 1.5 mm pitch connector,
snap-in mounting type*1
(Ta = 25°C)
Electro-optical characteristics
Low level output voltage
Supply voltage
VCC
VOL
VCC
Light
IOL
(V)
(V)
(mA)
(V)
cut-off
MIN.
MAX.
MAX.
Detecting
and
Slit width
emitting
(mm)
gap
(mm)
5.0
0.5
2.7
5.5
0.35
No
4
3.3
5.0
0.5
4.5
5.5
0.35
No
4
5
5.0
0.5
4.5
5.5
0.35
No
4
5
5.0
0.7
4.5
5.5
0.35
No
4
5
※ Topr: –20 to +75°C, –30 to +95°C (GP1A173LCS3F, GP1A173LCS2F, GP1A173LCSVF, GP1A273LCS1F)
*1 Applicable to 3 kinds of thickness of mounting boards.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
■
GP1A273LCS1F
Optoelectronics
GP1A173LCS3F
GP1A173LCS2F
GP1A173LCSVF
Photointerrupters
<Reflective type>
Phototransistor Output
<Compact>
♦Single
Model No.
Internal
connection
diagram
(Ta = 25°C)
Features
Electro-optical characteristics
Optimum
detecting
Current transfer ratio
Response time
distance CTR (%)
VCE
tr (µs)
IC
VCE
RL
IF
(mm)
(mA)
(V)
TYP. (mA) (kΩ)
(V)
MIN.
GP2S700HCP
Compact (4 × 3 × 2 [height] mm),
long focal distance, surface mounting leadless type
4
1.5
4
2
20
0.1
1
2
GP2S60
Thin (3.2 × 1.7 × 1.1 [height] mm), surface mounting
leadless type
1
1.0
4
2
20
0.1
1
2
※ Topr: –25 to +85°C
GP2S700HCP
GP2S60
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
49
OPTO
PHOTOINTERRUPTERS (REFLECTIVE TYPE)
★ Under
development
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Output ( light-detecting element and signal-processing circuit integrated onto a single chip. )
<With 3-pin connector terminal>
♦OPIC
Internal
connection
diagram
Model No.
GP2A200LCS0F
GP2A240LCS0F
GP2A250LCS0F
GP2A25J0000F
GP2A230LRS0F
GP2A230LRSAF
★ GP2A430LCSAF
GP2A25NJJ00F
GP2A25DJ000F
GP2A28AJ000F
(Ta = 25°C)
Electro-optical characteristics
Optimum
Supply voltage Dissipation current Low level output voltage
detecting
VCC
ICC
VOL
distance
VCC
VCC
(V)
(mA)
(V)
(mm)
(V)
(V)
MIN. MAX. MAX.
MAX.
Features
Multiple types of paper detectable, light modulation type,
5 to 15
with connector, sensitivity adjusted
Applicable to inverter fluorescent lamp,
5 to 15
light modulation type, with connector, sensitivity adjusted
(Following
diagram [A]) Static electricity resistant,
2.5 to
applicable to inverter fluorescent lamp,
12.5
light modulation type, with connector, sensitivity adjusted
Multiple types of paper detectable, light modulation type,
3 to 7
with connector, sensitivity adjusted
Compact, screw-clamp type, multiple types of paper
(Following detectable, light modulation type, with connector
diagram [B])
3 to 7
Compact, hook type, multiple types of paper detectable,
(Following light modulation type, with connector
diagram [C])
Multiple types of paper detectable, light modulation type,
sensitivity adjusted, improved light-resistance characteristic 3 to 7
for inverter lighting, built-in visible light cut filter
(Following
Multiple types of paper detectable, light modulation type,
diagram [A])
3 to 7
with connector, sensitivity adjusted
Multiple types of paper detectable, light modulation type,
3 to 7
with connector, sensitivity adjusted, hook type
4.75
5.25
30*1
5
0.4
5
4.75
5.25
30*1
5
0.4
5
4.75
5.25
30*1
5
0.4
5
4.75
5.25
30*1
5
0.4
5
4.75
5.25
20*1
5
0.4
5
3.0
5.5
10*1
3.3 to 5
0.4
3.3 to 5
4.75
5.25
30*1
5
0.4
5
4.75
5.25
30*1
5
0.4
5
4.75
5.25
30*1
5
0.4
5
※ Topr: –10 to +60°C (GP2A25J0000F, etc.)
–10 to +70°C (GP2A200LCS0F, GP2A240LCS0F, GP2A250LCS0F, GP2A230LRS0F, GP2A230LRSAF, GP2A430LCSAF)
*1 Smoothing value R L = ∞
[Internal connection diagram]
[A]
Voltage regulator
Demodulator
Amplifier
Comparator
Oscillator
Synchronous detector
GP2A25J0000F
⎧ GP2A25NJJ00F, GP2A200LCS0F, ⎫
⎜GP2A240LCS0F
⎜
⎩
⎭
GP2A250LCS0F
GP2A25DJ000F
GP2A230LRS0F
GP2A230LRSAF
[GP2A430LCSAF]
GP2A28AJ000F
[B]
Voltage regulator
Demodulator
(10kΩ)
Amplifier
Comparator
Oscillator
Synchronous detector
[C]
Voltage regulator
Amplifier
Comparator
50
Oscillator
Synchronous detector,
Demodulator
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
■
PHOTOINTERRUPTERS FOR SPECIFIC APPLICATIONS
Photointerrupters for Specific Applications
♦Transmissive
Type
<For amusement use>
Model No.
Internal
connection
diagram
Voltage regulator
GP1A204HCS0▲
(Ta = 0 to +40°C)
Features
Connector with lock,
screw mounting type,
high resistant to noise
Detecting
and emitting
gap
(mm)
Slit width
(mm)
4.0
0.5
Electro-optical characteristics
Operating voltage
Low level output voltage
VCC (V)
IOL
VCC
VOL (V) Light
MIN.
MAX.
MAX. cut-off
(mA)
(V)
10.8
24
0.4
Yes
5
10.8 to 24
Amplifier
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
Optoelectronics
GP1A204HCS0
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
51
OPTO
PROXIMITY SENSOR /
PROXIMITY SENSOR WITH INTEGRATED AMBIENT LIGHT SENSOR
☆ New
■ Proximity
Sensor
Absolute maximum ratings
Model No.
GP2AP002S30F
Features
Compact size (4.0 × 2.0 × 1.25 t mm)
Drastically reduced LED current consumption by
employing a light modulation system
Built-in LEDs for simple optical design and I2C output
(LED emission duty: MAX. 0.3%)
VCC
(V)
Topr
(°C)
3.8
–25 to +85
product
(Ta = 25°C)
Electro-optical characteristics
NonDetecting
Peak
Dissipation
detecting
distance
emission
current
distance
Lon
wavelength
ICC (µA)
Loff
(mm)
λp
TYP.
(mm)
MIN.
(nm)
MAX.
240
25
150
940
GP2AP002S30F
■ Proximity
Sensor with Integrated Ambient Light Sensor
Absolute maximum ratings
(Ta = 25°C)
Electro-optical characteristics
Proximity sensor portion
Model No.
GP2AP030A00F
☆GP2AP007A00F
☆GP2AP008T00F
Features
LED and ambient light sensor combined in
a single package (4.0 × 2.1 × 1.25 t mm)
Built-in LEDs for simple optical design
Illuminance output: digital 16-bit output
(Minimum detectable illuminance: 0.02 lx)
I2C output compatible (proximity sensor,
ambient light sensor)
LED and ambient light sensor combined in
a single package (2.5 × 2.0 × 1.0 t mm)
Compact with reduced mounting area
Illuminance output: digital 16-bit output
(Minimum detectable illuminance: 0.1 lx)
Small aperture compatible
I2C output compatible (proximity sensor,
ambient light sensor)
LED and ambient light sensor combined in
a single package (3.94 × 2.36 × 1.35 t mm)
Illuminance output: digital 16-bit output
(Minimum detectable illuminance: 0.1 lx)
Small aperture compatible
I2C output compatible (proximity sensor,
ambient light sensor)
GP2AP030A00F
52
Ambient light sensor portion
RecomADC
Peak
mended
conversion
emission
Output
illuminance
time
wavelength
resolution
range
Tint
(bit)
λp
Ev
(ms)
(nm)
(lx)
TYP.
VCC
(V)
Topr
(°C)
Dissipation
current
Icc
(µA)
TYP.
5.5
–35 to
+85
65
100
940
0.02 to
10 000
16
100
2.2 to
5.5
–30 to
+85
100
100
940
0.1 to
100 000
16
30
2.2 to
5.5
–30 to
+85
100
100
940
0.1 to
100 000
16
30
GP2AP007A00F
Detecting
distance
Lon
(mm)
TYP.
GP2AP008T00F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PROXIMITY/GESTURE SENSOR WITH
INTEGRATED AMBIENT LIGHT SENSOR / UV LIGHT SENSORS
OPTO
★ Under
■ Proximity/Gesture
Sensor with Integrated Ambient Light Sensor
Absolute maximum ratings
Model No.
GP2AP054A00F
development
Features
LED and ambient light sensor combined in
a single package (4.0 × 2.1 × 1.25 t mm)
Simultaneous operation of the gesture
recognition and illuminance functions is
possible
Low power consumption mode is available
for the proximity sensor
Capable of holding a total of 4 gesture
detection results
VCC
(V)
Topr
(°C)
5.5
–35 to
+85
(Ta = 25°C)
Electro-optical characteristics
Proximity/gesture
Ambient light sensor portion
Dissipasensor portion
Dissipation
tion
RecomADC
current Detecting
Peak
current
mended
conversion
Icc
distance
emission
Output
Icc
illuminance
time
(Gesture)
Lon
wavelength
resolution
(µA)
range
Tint
(µA)
(mm)
(bit)
λp
TYP.
Ev
(ms)
TYP.
TYP.
(nm)
(lx)
TYP.
100
320
100
940
0.02 to
10 000
16
30
■ UV
Light Sensors
(Ta = 25°C)
Absolute maximum ratings
Model No.
★GA1AUV100WP
Features
Detects only UV rays contained within
sunlight (no sensitivity to visible light)
Built-in ambient light sensor
Compact size: 2.0 × 1.6 × 0.6 t mm
I2C output compatible
VCC
(V)
I2C voltage
VI2C
(V)
2.2 to
5.5
1.7 to
Vcc
Electro-optical characteristics
Built-in
Dissipation
ADC
clock
current
Output conversion
Topr
frequency
Icc
resolution
time
(°C)
fosc
(µA)
(bit)
(ms)
(MHz)
TYP.
TYP.
TYP.
–35 to
+85
65
2.62
16
25
Recommended
illuminance range
Ev
(lx)
Sunlight
(AM1.5 equivalent)
Optoelectronics
GP2AP054A00F
UV: 0 to 200 000
Illuminance: 0 to 120 000
GA1AUV100WP
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
53
OPTO
■ OPIC
OPIC LIGHT DETECTORS
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
Light Detectors ( light-detecting element and signal-processing circuit integrated onto a single chip. )
Absolute maximum ratings
Model No.
IS485E
IS486E
Type
Built-in schmidt trigger
circuit, amplifier and
voltage regulator
EVLH
Package
VCC
(V)
Transparent
epoxy resin with
condenser (lens)
–0.5 to +17
175
50
–25 to +85
–
–0.5 to +17
175
50
–25 to +85
35
P
IO
(mW) (mA)
Topr
(°C)
(Ta = 25°C)
Electro-optical characteristics
EVHL
tPLH
tPHL
VCC
(V)
(µs)
TYP.
(µs)
TYP.
VCC
(V)
EV
(Ix)
RL
(Ω)
35
5
5
3
5
50
280
–
5
3
5
5
50
280
(Ix)
(Ix)
MAX. MAX.
IS485E
(IS486E)
<Model employing a light modulation system>
(Ta = 25°C)
Absolute maximum ratings
Model No.
IS471FE*1, *3
Type
Package
Built-in pulse driver
circuit at the emitter
Visible light
side, synchronous
cut-off epoxy
detector circuit,
resin
amplifier circuit and
demodulator circuit
VCC
(V)
–0.5 to +16
Topr
(°C)
VOL
(V)
MAX.
–25 to +60
0.35
P
IO
(mW) (mA)
250
50
Electro-optical characteristics*2
tPHL
tPLH
VOH
(V)
(µs)
(µs)
VCC
MIN.
(V)
TYP.
TYP.
4.97
400
400
5
RL
(Ω)
External
disturbing light
illuminance
EVDX(Ix) TYP.
280
7 000
*1 IS471FE is less susceptible to disturbing effects thanks to the light modulation system
*2 Vcc = 5 V
*3 Straight lead type (IS471FSE) is also available.
IS471FE
54
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PHOTOTRANSISTOR LINEUP /
PHOTOTRANSISTORS
OPTO
■ Phototransistor
Package
Epoxy resin with lens
Surface mounting
leadless type
Lineup
Output type
Single phototransistor
Model No.
Half
sensitivity
angle
Features
Visible light
cut-off
Standard
General purpose/Narrow acceptance
±13°
PT480E00000F
Compact, thin
±35°
PT4800E0000F
PT480FE0000F
PT4800FE000F /
PT4850FE000F▲
Darlington
phototransistor
High sensitivity/Narrow acceptance
±13°
PT481E00000F▲
PT481FE0000F▲
High sensitivity/Intermediate acceptance
±40°
—
Single phototransistor
Compact
(side view/top view mounting possible)
±15°
Darlington
phototransistor
Compact
(side view/top view mounting possible)
±15°
PT491FE0000F
PT100MC0MP
PT100MF0MP
—
PT100MF1MP
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
Model No.
PT100MC0MP
Single
PT100MF0MP*1
Absolute maximum ratings
Topr
PC
VCEO
(mW)
(°C)
(V)
Package
Surface mounting
leadless type with lens
35
75
75
–30 to +85
–30 to +85
MAX.
1.7
5.1
1.15
5
3.45
5
∆θ
(°)
TYP.
λp
(nm)
TYP.
20
±15
900
20
±15
910
ICEO(A)
VCE
(V)
Ee
(mW/cm2)
MAX.
1
1 × 10 –7
1
1×
10 –7
10 –7
PT480E00000F
35
75
–25 to +85
0.4
TYP. 1.7
5
1
1×
20
±13
800
PT480FE0000F*1
35
75
–25 to +85
0.25
TYP. 0.8
5
1
1 × 10 –7
20
±13
860
10 –7
35
75
–25 to +85
0.12
TYP. 0.4
5
1
1×
20
±35
800
PT4800FE000F*1
35
75
–25 to +85
0.08
TYP. 0.25
5
1
1 × 10 –7
20
±35
860
PT4850FE000F▲*1
35
75
–25 to +85
0.12
0.56
5
1
1 × 10 –7
20
±35
860
10 –6
PT4800E0000F
Epoxy resin with lens
PT481E00000F▲
Darlington
35
Ic (mA)
VCE
(V)
MIN.
PT481FE0000F▲*1
Epoxy resin with lens
PT491FE0000F*1
PT100MF1MP*1
35
75
–25 to +85
1.5
25
2
0.1
1×
10
±13
800
35
75
–25 to +85
0.9
27
2
0.1
1 × 10 –6
10
±13
860
1×
10 –6
10
±40
860
1×
10 –6
10
±15
860
35
Surface mounting
leadless type with lens
35
75
75
–25 to +85
–30 to +85
0.2
0.2
0.8
2
1.2
5
Ev, 2 Ix
0.01
Optoelectronics
Type
■ Phototransistors
*1 Visible light cut-off type
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
PT100MF0MP
⎧PT100MF1MP, ⎫
⎜PT100MC0MP: ⎜
⎜Transparent resin⎜
⎩
⎭
PT480E00000F
(PT481E00000F▲)
PT480FE0000F
(PT481FE0000F▲)
PT4800E0000F
⎧PT4800FE000F, ⎫
⎜
⎜
⎩PT4850FE000F▲⎭
PT491FE0000F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
55
OPTO
■ PIN
PIN PHOTODIODES
Photodiodes
Model No.
PD410PI2E00F
PD411PI2E00F
PD412PI2E00F▲
PD413PI2E00F
PD100MC0MP
PD100MF0MP
Features
(Ta = 25°C)
Package
(Material)
Visible light cut-off epoxy
resin with condenser (lens)
Transparent epoxy resin with
PIN type
condenser (lens)
Transparent epoxy resin with
condenser (lens)
PIN type
Visible light cut-off epoxy
IrDA1.0
resin with condenser (lens)
Surface mounting Transparent epoxy resin
leadless type
board with lens
Surface mounting Visible light cut-off epoxy
leadless type
resin board with lens
VR
(V)
tr, tf
(µs)
TYP.
VR
(V)
RL
(kΩ)
λp
(nm)
TYP.
1 × 10 –8
10
0.2
10
1
1 000
100
1 × 10 –8
10
0.2
10
1
960
3.5
100
1 × 10 –8
10
0.25
10
1
800
–25 to +85
MIN. 4.5
(TYP. 5.4)
100
1 × 10 –8
10
0.2
10
1
960
–
–30 to +85
0.6
100
1 × 10 –8
10
0.01
15
0.18
820
–
–30 to +85
0.4
100
1 × 10 –8
10
0.01
15
0.18
850
Topr
(°C)
Isc
(µA)
MIN.
3.31
–25 to +85
3.31
Active
area
(mm2)
Ev
(Ix)
Id
(A)
MAX.
2.5
100
–25 to +85
5.0
3.31
–25 to +85
3.31
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
PD410PI2E00F
⎧PD411PI2E00F: transparent; PD412PI2E00F : transparent,⎫
▲
⎜
⎜
⎩ PD413PI2E00F
⎭
56
PD100MC0MP
(PD100MF0MP: black)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
INFRARED EMITTING DIODE LINEUP /
INFRARED EMITTING DIODES
OPTO
Emitting Diode Lineup
Type
Single-end lead
(Side view type)
Surface mount type
Package
Half intensity
angle
Features
Epoxy resin with lens
Epoxy resin with lens/
leadless
General purpose/Narrow beam angle
±13°
GL480E00000F
Compact and thin
±30°
GL4800E0000F
Compact/Narrow beam angle
±10°
GL100MN0MP
±10°
GL100MN1MP
±80°
GL100MD1MP1
(Mountable for Top view/
Side view type)
High output type
Compact/Wide beam angle
■
Model No.
Infrared Emitting Diodes
Model No.
Package, features
GL480E00000F
(Ta = 25°C)
Absolute maximum ratings
VR
P
Topr
IF
(mA) (V) (mW)
(°C)
Radiant flux Φe (mW)
IF
MIN.
TYP.
(mA)
VF (V)
TYP.
MAX.
IF
(mA)
∆θ
(°)
TYP.
λp
(nm)
TYP.
50
6
75
–25 to +85
0.7
–
20
1.2
1.4
20
±13
950
50
6
75
–25 to +85
0.7
1.6
20
1.2
1.4
20
±30
950
50
6
75
–30 to +85
1.0
3.0
(MAX.)
20
1.2
1.4
20
±10
940
50
6
75
–30 to +85
2.0
6.0
(MAX.)
20
1.2
1.5
20
±10
940
50
6
75
–30 to +85
–
6.0
(MAX.)
20
–
1.5
20
±80
940
Epoxy resin with lens
GL4800E0000F
GL100MN0MP
GL100MN1MP
GL100MD1MP1
Surface mounting leadless type,
epoxy resin board with lens
Surface mounting leadless type,
epoxy resin board with lens,
high output type
Surface mounting leadless type,
epoxy resin board with lens,
wide beam angle
GL480E00000F
GL4800E0000F
Optoelectronics
■ Infrared
GL100MN0MP
(GL100MN1MP, GL100MD1MP1)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
57
OPTO
OPTICAL-ELECTRIC SENSOR LINEUP
★ Under
■ Distance
Measuring Sensor Lineup
Output
Detected distance
1-bit digital output according
to distance measuring
Analog voltage output
according to distance
measuring
(Including I2C output)
Features
Battery drive compatible, compact, 1-bit digital output
GP2Y0D805Z0F
10 cm
Battery drive compatible, compact, 1-bit digital output
GP2Y0D810Z0F
GP2Y0D815Z0F
15 cm
Battery drive compatible, compact, 1-bit digital output
13 cm
1-bit digital output
GP2Y0D413K0F
24 cm
1-bit digital output
GP2Y0D21YK0F
80 cm
1-bit digital output
GP2Y0D02YK0F
1.5 to 15 cm
2 to 15 cm
4 to 50 cm
CMOS type
Analog output
Analog output
GP2Y0AF15 series
GP2Y0A51SK0F
Analog output
GP2Y0A41SK0F / GP2Y0AF30 series
Analog output
GP2Y0E02A
I2C output
GP2Y0E02B
Analog, I2C output
GP2Y0E03
10 to 80 cm
Analog output
GP2Y0A21YK0F
10 to 150 cm
Compact (22 × 8 × 7.2 [T] mm),
Analog output
GP2Y0A60SZLF
20 to 150 cm
Analog output
GP2Y0A02YK0F
100 to 550 cm
Analog output
GP2Y0A710K0F
Sensor Unit Lineup
Output
Analog output
Digital output
Features
Model No.
Pulse analog output, single-shot detection of house dust,
general purpose
GP2Y1010AU0F
Single-shot detection of house dust, LED drive via external input,
high sensitivity
GP2Y1012AU0F
Digital (PWM) output, built-in microprocessor controller,
single-shot detection of house dust, high sensitivity
GP2Y1023AU0F
Digital (UART) output, built-in microprocessor controller,
sensing can discriminate between PM2.5 and PM10, internal
cleaning possible
58
Model No.
5 cm
4 to 30 cm
■ Dust
development
★GP2Y1030AU0F
OPTO
DISTANCE MEASURING SENSORS
■ Distance
Measuring Sensors (1)
♦Digital Output
GP2Y0D805Z0F
5
GP2Y0D810Z0F
10
GP2Y0D815Z0F
15
GP2Y0D413K0F
13
GP2Y0D21YK0F
24
GP2Y0D02YK0F
80
*1 Vcc = 5 V
Absolute maximum ratings
Features
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
digital voltage output according to the measured
distance
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
digital voltage output according to the measured
distance
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
long distance measuring type
(No external control signal required),
digital voltage output according to the measured
distance
Electro-optical characteristics*1
Dissipation current
VOL
(V)
Operating Standby
MAX.
(mA)
(µA)
Vcc
(V)
Topr
(°C)
VOH
(V)
MIN.
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
–
–
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
MAX. 40
–
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
MAX. 50
–
※ PSD: Position Sensitive Detector
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Optoelectronics
Model No.
Detected
distance
(cm)
(Ta = 25°C)
59
OPTO
DISTANCE MEASURING SENSORS
☆ New
product
■ Distance
Measuring Sensors (2)
♦ Analog Output (Including I2C output)
Model No.
Distance
measuring
range
(cm)
(Ta = 25°C)
Absolute maximum ratings
Features
Vcc
(V)
Topr
(°C)
–0.3 to +7
–10 to +60
☆GP2Y0AF15 series
1.5 to 15
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms), compact,
lineup of various connector shapes
GP2Y0A51SK0F
2 to 15
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms)
–0.3 to +7
–10 to +60
☆GP2Y0AF30 series
4 to 30
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms), compact,
lineup of various connector shapes
–0.3 to +7
–10 to +60
GP2Y0A41SK0F
4 to 30
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms)
–0.3 to +7
–10 to +60
GP2Y0E02A
4 to 50
–0.3 to +3.6
–10 to +60
GP2Y0E02B
4 to 50
–0.3 to +3.6
–10 to +60
GP2Y0E03
4 to 50
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
(16.7 × 11 × 5.2 mm), high-precision measurement,
analog / I2C output both compatible
–0.3 to +5.5
–10 to +60
GP2Y0A21YK0F
10 to 80
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
linear voltage output
–0.3 to +7
–10 to +60
GP2Y0A60SZLF
GP2Y0A02YK0F
GP2Y0A710K0F
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
(18.9 × 8 × 5.2 mm), high-precision measurement,
analog output
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
(18.9 × 8 × 5.2 mm), high-precision measurement,
I2C output
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
10 to 150 compact type (22 x 8 x 7.2 mm),
long distance measuring type
(No external control signal required)
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
20 to 150
long distance measuring type
(No external control signal required)
Distance measuring sensor united with PSD※,
infrared LED and signal processing circuit,
100 to 550
long distance measuring type
(No external control signal required)
–0.3 to +5.5
–10 to +60
–0.3 to +7
–10 to +60
–0.3 to +7
–10 to +60
*1 Vcc = 5 V
*2 When Vcc = 3 V: Vo (TYP.) = 0.35 V (at L = 150 cm); ∆Vo (TYP.) = 1.6 V (at L = 150 cm → 20 cm)
60
Electro-optical characteristics*1
Dissipation
VOH
VOL
current
(V)
(V)
Operating
MIN.
MAX.
(mA)
VO (TYP.) = 0.4 V
(at L = 15 cm),
TYP. 17
∆VO (TYP.) = 2.3 V
(at L = 15 cm → 1.5 cm)
VO (TYP.) = 0.4 V
(at L = 15 cm),
TYP. 12
∆VO (TYP.) = 2.25 V
(at L = 15 cm → 2 cm)
VO (TYP.) = 0.4 V
(at L = 30 cm),
TYP. 17
∆VO (TYP.) = 2.3 V
(at L = 30 cm → 4 cm)
VO (TYP.) = 0.4 V
(at L = 30 cm),
MAX. 22
∆VO (TYP.) = 2.25 V
(at L = 30 cm → 4 cm)
VOUT (A) 1 = 0.3 to 0.8 V
(at L = 50 cm),
MAX. 36
VOUT (A) 3 = 2.1 to 2.3 V
(at L = 4 cm)
D1 = 45 to 50 cm
(at L = 50 cm),
MAX. 36
D3 = 3 to 5 cm
(at L = 4 cm)
VOUT (A) 1 = 0.3 to 0.8 V,
D1 = 45 to 50 cm
(at L = 50 cm),
MAX. 36
VOUT (A) 3 = 2.1 to 2.3 V,
D3 = 3 to 5 cm
(at L = 4 cm)
VO (TYP.) = 0.4 V
(at L = 80 cm),
MAX. 40
∆VO (TYP.) = 1.9 V
(at L: 80 cm → 10 cm)
VO (TYP.) = 0.65 V *2
(at L = 150 cm),
∆VO (TYP.) = 3.0 V
(at L = 150 cm → 20 cm)
VO (TYP.) = 0.4 V
(at L = 150 cm),
∆VO (TYP.) = 2.05 V
(at L = 150 cm → 20 cm)
VO (TYP.) = 2.5 V
(at L = 100 cm),
∆VO (TYP.) = 0.7 V
(at L = 100 cm → 200 cm)
MAX. 50
MAX. 50
TYP. 30
※ PSD: Position Sensitive Detector
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
DISTANCE MEASURING SENSORS /
DUST SENSOR UNIT
★ Under
GP2Y0D805Z0F
⎧
⎫
GP2Y0D810Z0F,
⎜
GP2Y0D815Z0F, ⎜
⎜
GP2Y0D810Z1F ⎜
⎩
⎭
GP2Y0AF30 series
■ Dust
GP2Y0E02A
(GP2Y0E02B)
GP2Y0E03
GP2Y0A60SZLF
GP2Y0AF15 series
GP2Y0A21YK0F
GP2Y0A51SK0F
GP2Y0D02YK0F
(GP2Y0A02YK0F)
GP2Y0A710K0F
⎧ GP2Y0D21YK0F, ⎫
⎜GP2Y0A41SK0F ⎜
⎜
⎜
⎜GP2Y0D413K0F: ⎜
⎜without mounting ⎜
⎩ hole
⎭
Sensor Unit
Model No.
GP2Y1010AU0F
GP2Y1012AU0F
GP2Y1023AU0F
★GP2Y1030AU0F
development
Topr
(°C)
Features
• Built-in infrared emitting diode,
photodiode and signal processing circuit
• Compact, single-shot detection of house dust
• Output: Analog voltage
• High sensitivity
• Built-in infrared emitting diode,
photodiode and signal processing circuit
• Compact, single-shot detection of house dust
• Output: Analog voltage
• High sensitivity
• Built-in microcomputer
• Built-in infrared emitting diode,
photodiode and signal processing circuit
• Compact, single-shot detection of house dust
• Output: Digital signal output (PWM)
• Built-in infrared emitting diode,
photodiode and signal processing circuit
• Built-in microcomputer
• Sensing can discriminate between PM2.5 and
PM10
• Internal cleaning possible
GP2Y1010AU0F
(GP2Y1012AU0F, GP2Y1023AU0F)
(Ta = 25°C)
Electro-optical characteristics
Operating
Detection
supply voltage Dissipation
Output
current
concentration
(V)
(mA)
μg/m3 (TYP.)
4.5 to 5.5
TYP. 11
0 to 600
Analog voltage
4.5 to 5.5
TYP. 11
0 to 240
Analog voltage
4.75 to 5.25
TYP. 15
0 to 240
Digital signal (PWM)
Temperature correction
Averaging
3 to 5.5
TYP. 25
0 to 500
Digital signal (UART)
–10 to +65
Optoelectronics
OPTO
GP2Y1030AU0F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
61
OPTO
■ IR
IR DETECTING UNIT FOR REMOTE CONTROL LINEUP
(CLASSIFIED BY FORM)
Detecting Unit for Remote Control Lineup (Classified by Form)
Type
IR detecting unit
for remote control
Package
Detection
Form
position*1
(from PCB)
Lead L bend with
shield case
(holder)
16.0 mm*2
Features
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
12.0 mm*3
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
6.8 mm*4
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Lead straight
with shield case
(holder)
19.0 mm
9.6 mm
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Holderless
Lead straight
6.0 mm
bend*5
Lead L
5.3 mm
*1 L
ead straight: Distance from lens center to mounting board upper surface
No mesh lead L bend: Distance from tip of lens to mounting board upper surface
Mesh-type lead L bend: Distance from tip of mesh to mounting board upper surface
*2 Mesh type (strengthened resistance to electromagnetic induction noise): 16.4 mm
*3 Mesh type: 12.4 mm
*4 Mesh type: 7.2 mm
*5 Mesh type: 5.3 mm
62
Operating voltage
Model No.
3 to 5 V
GP1UE28XK0VF series
5V
GP1UM28XK0VF series
3 to 5 V
GP1UE28RK0VF series
5V
GP1UM28RK0VF series
3 to 5 V
GP1UE27XK0VF series
5V
GP1UM27XK0VF series
3 to 5 V
GP1UE27RK0VF series
5V
GP1UM27RK0VF series
3 to 5 V
GP1UE26XK0VF series
5V
GP1UM26XK0VF series
3 to 5 V
GP1UE26RK0VF series
5V
GP1UM26RK0VF series
3 to 5 V
GP1UE29QK0VF series
5V
GP1UM29QK0VF series
3 to 5 V
GP1UE28YK0VF series
5V
GP1UM28YK0VF series
3 to 5 V
GP1UE28QK0VF series
5V
GP1UM28QK0VF series
3 to 5 V
GP1UX31QS series
5V
GP1UX51QS series
3 to 5 V
GP1UX31RK series
5V
GP1UX51RK series
OPTO
Detecting Units for Remote Control
Absolute maximum ratings
Type
Series No.
GP1UM26XK0VF
With shield case (holder),
5 V drive
With shield case (holder),
5 V drive,
Strengthened resistance to
electromagnetic induction
noise
With shield case (holder),
3 to 5 V drive
With shield case (holder),
3 to 5 V drive,
Strengthened resistance to
electromagnetic induction
noise
Holderless, 5 V drive,
Strengthened resistance to
electromagnetic induction
noise
Holderless, 3 to 5 V drive,
Strengthened resistance to
electromagnetic induction
noise
(Ta = 25°C)
Electrical characteristics
VOH
VOL
fo
Icc
(V)
(V)
(kHz)
(mA)*1
MAX.
MIN.
MAX. TYP.
Vcc (V)
Topr (°C)
Operating
voltage
(V)
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
Size (mm)
0.45
*3
5.6 × 9.6 × 6.8
5.6 × 9.6 × 12.0
GP1UM27XK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM28XK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.0
GP1UM28YK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 8.6 ×
12.5(9.6)*2
GP1UM26RK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 9.6 × 7.2
5.6 × 9.6 × 12.4
5.6 × 9.6 × 16.4
GP1UM27RK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM28RK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM28QK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM29QK0VF
0 to 6.0
–10 to +70
4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UE26XK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 6.8
GP1UE27XK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 12.0
GP1UE28XK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.0
GP1UE28YK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 8.6 ×
12.5(9.6)*2
GP1UE26RK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 7.2
5.6 × 9.6 × 12.4
5.6 × 9.6 × 16.4
5.6 × 9.0 ×
12.5(9.6)*2
5.6 × 16.2 ×
21.9(19)*2
GP1UE27RK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UE28RK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UE28QK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UE29QK0VF
0 to 6.0
–10 to +70
2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UX51QS
0 to 6.0
–10 to +70
4.5 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UX51RK
0 to 6.0
–10 to +70
4.5 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
5.5 × 5.3 × 7.5
5.5 × 5.3 × 7.5
GP1UX31QS
0 to 6.0
–10 to +70
4.5 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UX31RK
0 to 6.0
–10 to +70
4.5 to 5.5
0.4
Vcc–0.5
0.45
*3
Terminal
layout
Center
Vcc
5.6 × 9.0 ×
12.5(9.6)*2
5.6 × 16.2 ×
21.9(19)*2
IR Devices
■ IR
IR DETECTING UNITS FOR REMOTE CONTROL
Center
GND
* A voltage regulator circuit is built-in but may be affected by the usage environment. Install with an externally mounted C and R as a power supply filter.
*1 When no signal is input (during input light).
*2 Figures in parentheses indicate the distance to the light detection center.
*3 fo = 32.75/36/36.7/38/40 kHz
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
63