INFINEON TLE7236SE

SP IDER
SPI Driver for Enhanced Relay Control
TLE7236SE
SPI Driver for Enhanced Relay Control
Dat a Sheet
Rev. 1.0, 2010-02-18
Aut omotive Po wer
SPI Driver for Enhanced Relay Control
TLE7236SE
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
2.1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
3.1
3.2
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4
4.1
4.2
4.3
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
11
12
5
5.1
5.2
5.3
5.4
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limp Home Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
14
15
6
6.1
6.2
6.3
6.4
6.5
6.6
Power Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channels 4 and 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inductive Output Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
16
17
18
19
20
7
7.1
7.2
7.3
7.4
7.5
7.6
Protection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Over Load Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Over Temperature Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESD protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reverse Polarity Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loss of Vbb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
21
21
21
22
8
8.1
8.2
Diagnostic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Command Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9
9.1
9.2
9.3
9.4
9.5
9.6
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daisy Chain Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11
Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
12
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Data Sheet
2
27
27
28
29
30
31
32
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
1
TLE7236SE
Overview
Features
•
•
•
•
•
•
8 bit SPI for diagnostics and control, providing daisy chain capability
Very wide range for digital supply voltage
Two configurable input pins offer complete flexibility for
PWM operation
Stable behavior at under voltage
Green Product (RoHS compliant)
AEC Qualified
PG-DSO-20-45
Description
The TLE7236SE is an eight channel high-side and low-side power switch in PG-DSO-20-45 package providing
embedded protective functions. It is especially designed for standard relays and LEDs in automotive applications.
The output stages incorporate two low-side, four high-side and two auto configuring high-side or low-side
switches.
A serial peripheral interface (SPI) is utilized for control and diagnosis of the device and the load. For direct control,
there are two input pins available.
The TLE7236SE provides a micro controller fail-safe function which is activated via a high signal at the limp home
input pin. There is a power supply integrated in the device to ensure this functionality even without digital supply
voltage.
The integrated power supply is designed to fulfill cranking mode requirements.
The power transistors are built by N-channel power MOSFETs. The device is monolithically integrated in
Smart Power Technology.
Type
Package
Marking
TLE7236SE
PG-DSO-20-45
TLE7236SE
Data Sheet
3
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Overview
Table 1
Product Summary
Operating range power supply voltage
Vbb
VDD
RDS(ON)
Digital supply voltage
Typical On-State resistance at 25 °C
4.0 … 28 V
3.0 … 5.5 V
high-side: 2 channels (Relay)
0.85 Ω
high-side: 2 channels (Generic, LED)
1.6 Ω
auto configuring: 2 channels (Relay, Supplies)
0.85 Ω
0.85 Ω
low-side: 2 channels (Relay)
IL(nom, min)
Nominal load current (all channels active)
Relay
280 mA
LED, Generic
140 mA
IDS(OVL, min)
IDS(OFF, max)
VDS(CL, min)
Vbb(CL, max)
fSCLK(max)
Over load switch off threshold
Output leakage current per channel at 25 °C
Drain to source clamping voltage
Source to ground clamping voltage
SPI clock frequency
500 mA
1 µA
41 V
-40 V
5 MHz
Protective Functions
•
•
•
Over load and short circuit protection
Thermal shutdown
Electrostatic discharge protection (ESD)
Diagnostic Functions
•
•
•
•
Latched diagnostic information via SPI
Open load detection in OFF-state
Over load detection in ON-state
Over temperature
Crank Mode
•
Integrated power supply enables secure operation at low battery voltage
Limp Home / Fail-Safe Functions
•
•
Limp home activation via pin LHI
Limp home configuration via input pins
Applications
•
•
•
Especially designed for driving relays and LEDs in automotive applications
All types of resistive and inductive loads
Suitable to switch 5 V power supply lines by auto configuring channels
Data Sheet
4
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Overview
Detailed Description
The TLE7236SE is an eight channel high-side and low-side relay switch providing embedded protective functions.
The output stages incorporate two low-side switches (0.85 Ω per channel), four high-side switches (two channels
with 0.85 Ω and two channels with 1.6 Ω) and two auto-configuring high-side or low-side switches (0.85 Ω per
channel). The auto-configuring switches can be utilized in high-side or low-side configuration just by connecting
the load accordingly. They are also suitable to switch a 5 V supply line in high-side configuration. Protective and
diagnostic functions adjust automatically to the chosen configuration.
The 8 bit serial peripheral interface (SPI) is utilized for control and diagnosis of the device and the loads. The SPI
interface provides daisy chain capability in order to assemble multiple devices in one SPI chain by using the same
number of micro-controller pins.
The outstanding feature of this octal relay switch enables the output channels to keep their state at low battery
voltage. This is realized by an integrated power supply, especially designed to fulfill cranking mode requirements
(Vbat = 4 V) independent from digital power supply (VDD). The SPI functionality is given only when the digital power
supply is available.
Furthermore, the TLE7236SE is equipped with two input pins that can be individually routed to the output control
of each channel thus offering complete flexibility in design and PCB-layout. The input multiplexer is controlled via
SPI.
In limp home mode (fail-safe mode), the input pins are directly routed to the configurable output channels 4 and
5. The limp home mode operates independently of digital power supply and is activated via pin LHI.
The device provides full diagnosis of the load via open load, over load and short circuit detection. SPI diagnosis
flags indicate latched fault conditions that may have occurred.
Each output stage is protected against short circuit. In case of over load, the affected channel switches off. There
are temperature sensors available for each channel to protect the device against over temperature.
The device protects itself with a built in reverse polarity protection which prohibits intrinsic current flow through the
logic during reverse polarity. However the output stages still incorporate a reverse diode where current can flow
through during reverse polarity.
The power transistors are built by N-channel power MOSFETs. The inputs are ground referenced CMOS
compatible. The device is monolithically integrated in Smart Power Technology.
Data Sheet
5
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Block Diagram
2
Block Diagram
VBB
temperature
sensor
crank mode
power supply
high-side
gate control
LHI
IN1
IN2
limp home
mode activation
input mux
input register
short circuit
detection
open load
detection
control,
diagnostic
and
protective
functions
SPI
D4
D5
auto
configuring
gate control
VDD
CS
SCLK
SI
SO
OUT0
OUT1
OUT2
OUT3
S5
S4
stand-by
control
OUT6
OUT7
low-side
gate control
diagnosis register
reverse polarity protection
GND
Overview_6.emf
Figure 1
Data Sheet
Block Diagram
6
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Block Diagram
2.1
Terms
Figure 2 shows all terms used in this data sheet.
Vbat
IS
IOUT_S0
VBB
VDS0
OUT0
IOUT_S1
OUT1
ILHI
IIN1
VLHI
IIN2
VIN1
IDD
VIN 2
I CS
VDD
V CS
ISCLK
VSCLK
ISI
VSI
ISO
VSO
LHI
OUT2
IN1
OUT3
IN2
D4
VDD
TLE7236SE
S4
CS
D5
SCLK
S5
SI
IOUT_S2
IOUT_S3
V DS2
VS1
VDS3
VS 2
IOUT_D4 V S3
IOUT_S4
VDS4
IOUT_S5
VS 4
VDS5 VD5
IOUT_D6
VS 5
OUT6
GND
OUT7
V D4
IOUT_D5
IOUT_D7
SO
VDS1
VS 0
VDS6
VDS 7
IGND
Terms_6.emf
Figure 2
Terms
In all tables of the electrical characteristics is valid:
Channel related symbols without channel number are valid for each channel separately (e.g. VDS specification is
valid for VDS0 … VDS7). In order to make the description of output currents easier, the load current IOut is equivalent
to the drain current IOUT_D in low-side configuration and the source current IOUT_S in high-side configuration.
All SPI register bits are marked as follows: ADDR.PARAMETER (e.g. ICR01.INX1). In SPI register description,
the values in bold letters (e.g. 0) are default values.
Data Sheet
7
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Pin Configuration
3
Pin Configuration
3.1
Pin Assignment
l
(top view )
VBB
1
20
OUT0
OUT1
2
19
OUT2
OUT3
3
18
VDD
LHI
4
17
CS
IN1
5
16
SCLK
IN2
6
15
SI
D5
7
14
SO
OUT7
8
13
D4
S5
9
12
OUT6
10
11
S4
GND
P-DSO20-45.emf
Figure 3
Pin Configuration PG-DSO20-45
3.2
Pin Definitions and Functions
Pin
Symbol
I/O
Function
-
Digital power supply
Power Supply
18
VDD
1
VBB
-
Power supply
10
GND
-
Digital, analog and power ground
Power Stages
20
OUT0
O
Source of high side power transistor channel 0
2
OUT1
O
Source of high side power transistor channel 1
19
OUT2
O
Source of high side power transistor channel 2
3
OUT3
O
Source of high side power transistor channel 3
13
D4
O
Drain of auto configuring power transistor 4
11
S4
O
Source of auto configuring power transistor 4
7
D5
O
Drain of auto configuring power transistor 5
9
S5
O
Source of auto configuring power transistor 5
12
OUT6
O
Drain of low side power transistor channel 6
8
OUT7
O
Drain of low side power transistor channel 7
LHI
I
Limp home activation input pin (pull down)
Inputs
4
Data Sheet
8
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Pin Configuration
Pin
Symbol
I/O
Function
5
IN1
I
Input multiplexer input 1 pin (pull down)
6
IN2
I
Input multiplexer input 2 pin (pull down)
CS
I
SPI Chip select (pull up)
16
SCLK
I
Serial clock
15
SI
I
Serial data in
14
SO
O
Serial data out
SPI
17
Data Sheet
9
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Electrical Characteristics
4
Electrical Characteristics
4.1
Absolute Maximum Ratings 1)
Stresses above the ones listed here may affect device reliability or may cause permanent damage to the device.
The values below are not considering combinations of different maximum conditions at one time
Tj = -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin
(unless otherwise specified)
Absolute Maximum Ratings1)
Pos.
Parameter
Symbol
Limit Values
Unit
Test Conditions
min.
max.
-40
40
V
-40V max. 2 minutes
-0.3
5.5
V
–
0
28
V
–
A
–
Power Supply
4.1.1
Power supply voltage
4.1.2
Digital supply voltage
4.1.3
Power supply voltage for short circuit
protection (single pulse)
Vbb
VDD
Vbat(SC)
Power Stages
4.1.4
Load current
IL
channel 0, 1, 4, 5, 6, 7
4.1.5
4.1.6
4.1.7
4.1.8
-0.5
0.5
channel 2, 3
-0.25
0.25
VDS
Power transistor’s source voltage
VOut_S
Power transistor’s drain voltage
VOut_D
Max. energy dissipation one channel single EAS
–
41
V
–
-16
–
V
–
–
41
V
–
mJ
2)
Voltage at power transistor
pulse for ch. 0, 1, 4, 5, 6, 7
4.1.9
Maximum energy dissipation one channel
repetitive pulses for ch. 0, 1, 4, 5, 6, 7
–
65
–
50
EAR
Tj(0) = 105 °C
ID(0) = 0.35 A
Tj(0) = 150 °C
ID(0)= 0.250 A
mJ
1 · 104 cycles
–
18
1 · 106 cycles
–
13
4.1.10 Max. energy dissipation one channel single EAS
pulse for ch. 2,3
Tj(0) = 105 °C
ID(0) = 0.250 A
Tj(0) = 105 °C
ID(0) = 0.220 A
mJ
–
50
–
30
2)
2)
Tj(0) = 105 °C
ID(0) = 0.250 A
Tj(0) = 150 °C
ID(0)= 0.250 A
1) not subject to production test
Data Sheet
10
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Electrical Characteristics
Tj = -40 °C to +150 °C; all voltages with respect to ground, positive current flowing into pin
(unless otherwise specified)
Absolute Maximum Ratings1)
Pos.
Parameter
Symbol
Limit Values
min.
4.1.11 Maximum energy dissipation one channel
repetitive pulses for ch. 2,3
Unit
Test Conditions
mJ
2)
max.
EAR
1 · 104 cycles
–
12
1 · 106 cycles
–
11
-0.3
Tj(0) = 105 °C
ID(0) = 0.180 A
Tj(0) = 105 °C
ID(0) = 0.180 A
Logic Pins
VIN
VLHI
4.1.12 Voltage at input pins
4.1.13 Voltage at LHI pin
4.1.14 Voltage at chip select pin
4.1.15 Voltage at serial clock pin
4.1.16 Voltage at serial input pin
4.1.17 Voltage at serial output pin
3)
VCS
VSCLK
VSI
VSO
-0.3
-0.3
VDD + 0.3
5.5
VDD + 0.3
VDD + 0.3
VDD + 0.3
VDD + 0.3
Tj
Tstg
-40
150
°C
–
-55
150
°C
–
VESD
-2
2
kV
HBM4)
-0.3
-0.3
-0.3
V
V
–
V
3)
V
3)
V
3)
V
3)
Temperatures
4.1.18 Junction Temperature
4.1.19 Storage Temperature
ESD Susceptibility
4.1.20 ESD susceptibility on all pins
1) not subject to production test
2) Pulse shape represents inductive switch off: IL(t) = IL(0) * (1 - t / tpulse); 0 < t < tpulse
3) VDD + 0.3 V < 5.5 V
4) ESD susceptibility, HBM according to EIA/JESD 22-A114
4.2
Pos.
Functional Range
Parameter
Symbol
Limit Values
Unit
Conditions
Min.
Max.
9
16
V
–
4.2.1
Supply Voltage Range for
Nominal Operation
Vbb(nom)
4.2.2
upper Supply Voltage Range for
Extended Operation
Vbb(ext),up 16
28
V
Parameter
Deviations possible
4.2.3
lower Supply Voltage Range for
Extended Operation
Vbb(ext),low 4
9
V
Parameter
Deviations possible
4.2.4
Junction Temperature
Tj
150
°C
–
-40
Note: Within the functional range the IC operates as described in the circuit description. The electrical
characteristics are specified within the conditions given in the related electrical characteristics table.
Data Sheet
11
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Electrical Characteristics
4.3
Thermal Resistance
Note: This thermal data was generated in accordance with JEDEC JESD51 standards.
For more information, go to www.jedec.org.
Thermal Resistance1)
Pos.
Parameter
Symbol
Limit Values
Unit
Conditions
Min.
Typ.
Max.
4.3.1
Junction to Case, bottom
–
–
4.3.2
Junction to Case, top
–
4.3.3
Junction to Pin (5,6,15 or 16)
4.3.4
Junction to Ambient
(1s0p, min. footprint)
RthJC,back
RthJC,top
RthJPin
RthJA,min
25
K/W
2)
–
30
K/W
2)
–
–
23
K/W
2)
–
80
–
K/W
3)
4.3.5
Junction to Ambient
(1s0p+300mm2Cu)
RthJA,300
–
65
–
K/W
4)
4.3.6
Junction to Ambient
(1s0p+600mm2Cu)
RthJA,600
–
60
–
K/W
5)
4.3.7
Junction to Ambient (2s2p)
RthJA,2s2p
–
52
–
K/W
6)
1) Not subject to production test
2) Specified RthJSP value is simulated at natural convection on a cold plate setup (all pins are fixed to ambient temperature).
Ta = 85 °C. Ch1 to Ch8 are dissipating 1 W power (0.125 W each).
3) Specified RthJA value is according to Jedec JESD51-2,-3 at natural convection on FR4 1s0p board; The product
(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm board with minimal footprint copper area and 70 µm thickness.
Ta = 85 °C, Ch1 to Ch8 are dissipating 1 W power (0.125 W each).
4) Specified RthJA value is according to Jedec JESD51-2,-3 at natural convection on FR4 1s0p board; The product
(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm board with additional heatspreading copper area of 300mm2
and 70 µm thickness. Ta = 85 °C, Ch1 to Ch8 are dissipating 1 W power (0.125 W each).
5) Specified RthJA value is according to Jedec JESD51-2,-3 at natural convection on FR4 1s0p board; The product
(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm board with additional heatspreading copper area of 600mm2
and 70 µm thickness. Ta = 85 °C, Ch1 to Ch8 are dissipating 1 W power (0.125 W each).
6) Specified RthJA value is according to Jedec JESD51-2,-7 at natural convection on FR4 2s2p board; The product
(Chip+Package) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70 µm Cu, 2 x 35 µm Cu).
Ta = 85 °C, Ch1 to Ch8 are dissipating 1 W power (0.125 W each).
Data Sheet
12
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Supply
5
Power Supply
The TLE7236SE is supplied by two supply voltages Vbb and VDD. The Vbb supply line is connected to a battery feed
and used by the power switches and by an integrated power supply for the register banks. The internal power
supply is designed to hold the state of the power switches including the configuration stored in the control register
bank during cranking down to 4V. There is an under voltage reset function implemented for the Vbb power supply,
which is triggered if Vbb is below the undervoltage threshold. After start-up of the power supply, all SPI registers
are reset to their default values and the device is in sleep mode (standby). Sending the SPI command
CMD.WAKE = 1 switches the device to operation mode (ON), while a command CMD.STB = 1 send the device to
sleep mode (standby) again. Please note that the device needs the time twu(Sleep) to initialize itself. No SPI
command should be send after changing the power state via CMD.WAKE = 1 before this time is elapsed. A SPI
frame send during twu(Sleep) could be ignored.
The VDD supply line is used to power the circuitry related to the SPI shift register and for driving the SO line. As a
result, the daisy chain function is available as soon as VDD is provided in the specified range independent of Vbb.
A capacitor between pins VDD and GND is recommended (especially in case of EMI disturbances).
Please see Figure 14 “Application Diagram” on Page 35 for details.
5.1
Operation Modes
There is a limp home functionality implemented in the TLE7236SE, which is activated via pin LHI. Please refer to
Section 5.2 for details.
The device provides a sleep mode (stand by) to minimize current consumption, which also resets the register
banks. It is entered and left by dedicated SPI commands . The sleep mode current is minimized only when limp
home is inactive. After limp home, the device enters sleep mode automatically.
The internal power supply is designed for low voltage cranking condition down to Vbb = 4 V. During cranking, the
output channels keep their state as before configured via SPI independent of VDD supply voltage. If VDD = 0 V the
SPI can not be used as the output and input levels refer to VDD, but the device keep the current state until either
the limp home mode is triggered or the VDD voltages comes back and therefore the SPI Interface works again.
The following table shows the operation modes depending on Vbb, VDD and the limp home input signal LHI.
Operation Modes
VBB
0V
0V
0V
4V
4V
4V
12 V
12 V
12 V
12 V
VDD
0V
5V
5V
0V
0V
3V
0V
0V
5V
5V
LHI
X
0V
5V
0V
4V
0V
0V
5V
0V
5V
Switches operating
-
-
-
✓
✓
✓
✓
✓
✓
✓
Limp Home
-
-
-
-
✓
-
-
✓
-
✓
SPI & daisy-chain
-
✓
✓
-
-
✓
-
-
✓
✓
Register Banks
reset
reset
reset
✓
reset
✓
✓
reset
✓
reset
Diagnostic functions
-
-
-
-
-
-
✓
-
✓
-
5.2
Limp Home Mode
The TLE7236SE offers the capability of driving dedicated channels during fail-safe operation of the system. This
limp home mode is activated by a high signal at pin LHI. In limp home mode, the SPI registers are reset and the
input pins are directly routed to the auto configuring channels (channel 4 and 5). As a result, the limp home
operation can be chosen for high-side and low-side driven loads. Due to the integrated power supply, limp home
operation is independent of digital power supply VDD. In case of stand-by, a high signal at pin LHI will wake up the
device. After limp home operation, the device enters sleep mode in any case.
Data Sheet
13
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Supply
5.3
Reset
There are several reset trigger implemented in the device. A reset switches off all channels and sets the registers
to default values. After any kind of reset, the transmission error flag (TER) is set and the device is in sleep mode.
Under Voltage Reset:
During this device condition a read on SPI delivers the Standard Diagnostic Frame with a TER flag, if VDD is above
the under voltage threshold already, if not SPI is not working.
This under voltage reset is released when VDD and Vbb supply voltage levels are above under voltage threshold.
Reset Command: There is a reset command available to reset all register bits of the register bank and the
diagnosis registers. As soon as CMD.RST = 1, a reset is triggered.
Limp Home Mode: In limp home mode, the SPI write-registers are reset. The SPI interface is operating normally,
so the limp home bit LHI as well as the diagnosis flags can be read, but no command is accepted until the device
leaves the Limp home operation.
Data Sheet
14
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Supply
5.4
Electrical Characteristics
Unless otherwise specified:
VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min. typ.
max.
9
16
V
–
Power Supply Vbb
5.4.1 Supply Voltage Range for
Nominal Operation
Vbb(nom)
5.4.2 upper Supply Voltage Range for
Extended Operation
Vbb(ext),up 16
28
V
Parameter Deviations possible
5.4.3 lower Supply Voltage Range for
Extended Operation
Vbb(ext),low 4
9
V
RL = 80 Ω
VDS < 1.5 V
Parameter Deviations possible
5.4.4 Under voltage reset threshold
5.4.5 Operating current drawn from Vbb
Vbb(UV)
IS(ON)
–
–
4
V
–
–
15
mA
–
–
12
mA
VDD= 0V
1)
Vbb = 16 V
Vbb = 16 V
all diagnosis off
µA
5.4.6 Sleep mode operating current with IS(Sleep)
disconnected loads (stand by)
Vbb = 16 V
VLHI = 0 V ; AWK= 0
Tj = 25 °C1)
Tj = 85 °C 1)
Tj = 150 °C
–
–
10
–
–
13
–
–
20
VDD
VDD(PO)
IDD(ON)
3.0
–
5.5
V
–
–
3.0
V
–
–
0.4
mA
fSCLK = 0 Hz
AWK= 1
VCS = 0V
IDD(DO)
–
3
5
mA
1)
Digital Power Supply VDD
5.4.7 Logic supply voltage
5.4.8 Under voltage reset threshold
5.4.9 Logic supply current
5.4.10 Logic supply current during VBB
dropout
fSCLK = 0 Hz
Vbb < Vbb(UV)
AWK= 1
VCS = 0V
5.4.11 Logic supply sleep mode current
µA
IDD(Sleep)
VCS = VDD
AWK = 0
Tj = 25 °C1)
–
–
20
–
–
20
–
–
40
–
–
200
µs
1)
–
–
1
µs
1)
–
–
1
µs
1)
Tj = 85 °C 1)
Tj = 150 °C
Timings
twu(Sleep)
5.4.13 Vbb under voltage reset delay time tbb(UVR)
5.4.14 VDD under voltage reset delay time tDD(UVR)
5.4.12 Sleep mode wake-up time
1) Not subject to production test, specified by design.
Note: Characteristics show the deviation of parameter at the given supply voltage and junction temperature.
Typical values show the typical parameters expected at Vbb = 13.5 V, VDD = 5.0 V, Tj = 25 °C.
Data Sheet
15
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Stages
6
Power Stages
The TLE7236SE is an eight channel high-side and low-side relay switch. The power stages are built by N-channel
vertical power MOSFET transistors. The gates of the high-side switches are controlled by charge pumps.
6.1
Input Circuit
There are two input pins available at TLE7236SE, which can be configured to be used for control of the output
stages. The INXn parameter of the input configuration register provide following possibilities:
•
•
•
•
channel is switched off
channel is switched according to signal level at input pin IN1
channel is switched according to signal level at input pin IN2
channel is switched on
Figure 4 shows the input circuit of TLE7236SE.
Channel 7
Channel 6
Channel 5
Channel 4
Channel 3
Channel 2
Channel 1
Channel 0
IN1
IIN1
0
IN2
IIN2
1
INX0
InputLogic.emf
Figure 4
Input Multiplexer
The current sink to ground ensures that the channels switch off in case of open input pin. The zener diode protects
the input circuit against ESD pulses.
6.2
Channels 4 and 5
The TLE7236SE provides two auto-configuring high-side or low-side switches (channels 4 and 5). They adjust the
diagnostic and protective functions according their potentials at drain and source automatically.
In high-side configuration, the load is connected between ground and source of the power transistors (S4 or S5).
The drain of the power transistors (D4 and D5) can be connected to any potential between GND-pin potential and
VBB-pin potential. When the drain is connected to VBB, the channel behave like the other high side channels. The
drain can also be connected to a 5 V power supply and the source pin will be utilized as switched 5 V supply line.
In low-side configuration, the source of the power transistors are to be connected to GND.
The configuration can be chosen for each of these channels individually, so it is feasible to connect one channel
in low-side and the other in high-side configuration.
Data Sheet
16
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Stages
6.3
Inductive Output Clamp
When switching off inductive loads with low-side switches, the potential at pin OUT rises to VDS(CL) potential,
because the inductance intends to continue driving the current. For the high-side channels, the potential at pin
OUT drops below ground potential to VS(CL). The voltage clamping is necessary to prevent destruction of the
device, see Figure 5 for details. Nevertheless, the maximum allowed load inductance is limited by the max.
clamping energy EAR see electrical characteristics “EAR” on Page 10.
V bb
high side
channel
low side
channel
VBB
OUT
ID
IL
L,
RL
VD
V DS(CL)
OUT
V S(CL)
VDS(CL)
IS
VS
GND
IL
L,
RL
GND
OutputClamp.emf
Figure 5
Output Clamp Implementation
Maximum Load Inductance
During demagnetization of inductive loads, energy has to be dissipated in the TLE7236SE. This energy can be
calculated with following equations:
V bb – V DS(CL) 

RL ⋅ IL
L
- ⋅ ln 1 – ---------------------------------E = V DS(CL) ⋅ ----------------------------------  + I L ⋅ -----R
RL
V
–
V

L
bb
DS(CL) 
Low-side
(1)
V S(CL) 
R L ⋅ I L
L
- ⋅ ln  1 – --------------E = ( V bb – V S(CL) ) ⋅ --------------- + I L ⋅ -----RL
RL
V S(CL)

High-side
(2)

V bb
2 
1
E = --- LI L ⋅  1 – ----------------------------------
2
V bb – V DS(CL) 

Low-side
(3)
V bb 
2 
1
E = --- LI L ⋅  1 – ---------------
2
V S(CL)

High-side
(4)
These equations simplify under the assumption of RL = 0:
The maximum energy, which is converted into heat, is limited by the thermal design of the component.
Data Sheet
17
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Stages
6.4
Timing Diagrams
The power transistors are switched on and off with a dedicated slope via the INX bits of the serial peripheral
interface (SPI). The switching times tON and tOFF are designed equally.
IN
VDS
tON
tOFF
t
80%
20%
t
Figure 6
SwitchOn .emf
Switching a Resistive Load
In input mode, a high signal at the input pin is equivalent to a SPI ON command and a low signal to SPI OFF
command respectively. Please refer to Section 9.3 for details on SPI protocol.
Data Sheet
18
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Stages
6.5
Electrical Characteristics
Unless otherwise specified: VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
typical values: VDD = 5.0 V, VBAT = 13.5 V, Tj = 25 °C
Pos. Parameter
Symbol
Limit Values
min.
typ.
Unit Test Conditions
max.
Output Characteristics
6.5.1 On-State resistance
channel 0, 1, 4, 5, 6, 7
channel 2, 3
6.5.2 Nominal load current
Ω
RDS(ON)
–
0.85
–
–
1.4
1.8
–
1.6
–
–
2.6
3.8
IOut(nom)
mA
IL = 220 mA
Tj = 25 °C
Tj = 150 °C
IL = 110 mA
Tj = 25 °C
Tj = 150 °C
all channels on
Ta = 100 °C
Tj,max = 150 °C
based on Rthja
channel 0, 1, 4, 5, 6, 7
280
410
–
1)
channel 2, 3
140
205
–
1)
–
–
1
–
–
2
–
–
5
6.5.3 Output leakage current in sleep mode
6.5.4 Output clamping voltage
µA
IOut(Sleep)
–
-16
V
–
VOUT_DS(CL) 41
–
–
V
–
VIN(L)
VIN(H)
∆VIN
IIN(L)
IIN(H)
0
–
0.6
V
–
1.8
–
5.5
V
–
–
0.1
–
V
1)
1.5
–
–
µA
10
40
80
µA
VIN = 0.6 V 1)
VIN = 5 V
µs
Vbb = 13.5 V
VOUT_S(CL)
–
VDS = 13.5 V
Tj = 25 °C1)
Tj = 85 °C 1)
Tj = 150 °C
Input Characteristics (IN & LHI)
6.5.5 L level
6.5.6 H level
6.5.7 Input voltage hysteresis
6.5.8 L-input pull-down current
6.5.9 H-input pull-down current
Timings
6.5.10 Turn-on time
VDS = 20% Vbat
tON
resistive load
channel 0, 1,4,5
–
–
100
channel 2, 3
–
–
100
channel 6,7
–
–
100
6.5.11 Turn-off time
VDS = 80% Vbb
µs
tOFF
IDS= 250 mA
IDS= 120 mA
IDS = 250 mA
Vbb = 13.5 V
resistive load
channel 0, 1, 4, 5
–
–
100
channel 2, 3 (HS)
–
–
100
channel 6, 7 (LS)
–
–
100
IDS = 250 mA
IDS = 120 mA
IDS = 250 mA
1) Not subject to production test, specified by design.
Data Sheet
19
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Power Stages
6.6
Command Description
Input Configuration Registers
ICR01
000B
3
2
1
0
INX1
INX0
rw
rw
ICR23
001B
3
2
1
0
INX3
INX2
rw
rw
ICR45
010B
3
2
1
0
INX5
INX4
rw
rw
ICR67
011B
3
2
1
0
INX7
INX6
rw
rw
Field
Bits
Type
Description
INXn
n = 7 to 0
[3:2], [1:0]
rw
Input Multiplexer Configuration Channel n
00 Channel n is switched off
01 Channel n is switched by input 1
10 Channel n is switched by input 2
11 Channel n is switched on
Data Sheet
20
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Protection Functions
7
Protection Functions
The device provides embedded protective functions. Integrated protection functions are designed to prevent IC
destruction under fault conditions described in this data sheet. Fault conditions are considered as “outside” normal
operating range. Protection functions are not designed for continuous repetitive operation.
7.1
Over Load Protection
The TLE7236SE is protected in case of over load or short circuit of the load. After time tOFF(OVL), the over loaded
channel n switches off and the according diagnosis flag Dn is set. The channel can be switched on after clearing
the protection latch by command CMD.CPL = 1. The CPL command clears itself with the next valid SPI
communication frame. Please refer to Figure 7 for details.
IN
t
ID0
I D0(OV L)
tOFF(OV L)
CPL = 1b
D0 = 1b
t
D0 = 00b
OverLoad.emf
Figure 7
Shut Down at Over Load
7.2
Over Temperature Protection
A temperature sensor for each channel causes an overheated channel to switch off to prevent destruction. The
according diagnosis flag is set. This flag is also set in OFF state, if the regarding channel temperature is too
high.The channel can be only switched on after clearing the protection latch by SPI command CMD.CPL = 1. The
CPL command clears itself with the next valid SPI communication frame. Please refer to “Diagnostic Features”
on Page 23 for information on diagnosis features.
7.3
ESD protection
There is a designed in protection against ESD disturbances up to the specified limit by using the defined model.
Please see electrical characteristics “ESD susceptibility on all pins” on Page 11
7.4
Reverse Polarity Protection
There is a reverse polarity protection implemented in the TLE7236SE. This protection has to be divided into two
parts. First the protection of the control circuits and second in the protection of the power transistors.
The control circuits are reverse polarity protected by protective measures in the ground connection. In case of
reverse polarity, there is no current flow through the control circuits.
The power transistors contain intrinsic body diodes that cause power dissipation. The reverse current through
these intrinsic body diodes has to be limited by the connected loads. The over temperature and over load
protection are not active during reverse polarity.
7.5
Loss of Vbb
In case of loss of Vbb connection in on-state, all inductances of the loads have to be demagnetized through the an
additional path from Vbb to ground. Usually this path is given somewhere in the PCB circuitry, for example, as a
suppressor diode like in the application diagram (see D1 in Figure 14 “Application Diagram” on Page 35).
Data Sheet
21
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Protection Functions
7.6
Electrical Characteristics
Unless otherwise specified:
VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
typical values: VDD = 5.0 V, VBAT = 13.5 V, Tj = 25 °C
Pos. Parameter
Symbol
Limit Values
min.
typ.
Unit Test Conditions
max.
Over Load Protection
7.6.1 Over load detection current at channel
0,1,4,5,6,7
IOut(OVL)
7.6.2 Over load detection current at channel 2,3 IOut(OVL)
7.6.3 Over load shut-down delay time
0.5
1.0
A
0.22
0.5
A
60
µs
tOFF(OVL)
Over Temperature Protection
7.6.4 Thermal shut down temperature
Tj(SC)
150
1701)
°C
1) Not subject to production test, specified by design
Data Sheet
22
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Diagnostic Features
8
Diagnostic Features
The SPI of TLE7236SE provides diagnosis information about the device and about the load. The diagnosis
information of the protective functions of channel n is latched in the diagnosis flags Dn. It is cleared by the SPI
command CMD.CPL = 1. The CPL command clears itself with the next valid SPI communication frame.
The open load diagnosis of channel n is latched in the diagnosis flag OLn. This flag is cleared by reading the
according diagnosis register.
Following table shows possible failure modes and the according protective and diagnostic action.
Failure Mode
Comment
Open Load
Diagnosis, when channel n is switched on: none
Diagnosis, when channel n is switched off: according to voltage level at the
output pin, flag OLn is set after time td(OL).
A diagnosis current can be enabled by SPI command DCCR.DCENn = 1.
Over Temperature
When over temperature occurs, the according diagnosis flag Dn is set. If the
affected channel n was active it is switched off.
The diagnosis flags are latched until they have been cleared by SPI
command CMD.CPL = 1.
Over Load
(Short Circuit)
When over load is detected at channel n, the affected channel is switched
off after time tOFF(OVL) and the dedicated diagnosis flag Dn is set.
The diagnosis flags are latched until they have been cleared by SPI
command CMD.CPL = 1.
Data Sheet
23
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Diagnostic Features
8.1
Electrical Characteristics
Unless otherwise specified:
VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
typical values: VBAT = 13.5 V, VDD = 5.0 V, Tj = 25 °C
Pos.
Parameter
Symbol
Limit Values
min.
typ.
Uni Test Conditions
t
max.
100
–
250
µs
–
OFF State Diagnosis
8.1.1
Open load diagnosis delay time
td(OL)
High Side Channels 0,1,2,3
8.1.2
Open load detection threshold voltage for VD(OL0..3) 3
Channel 0,1,2,3
4
5
V
1)
8.1.3
Output diagnosis current channel 0,1,2,3 IL(DC0..3)
200
300
µA
measured at VD(OL)
threshold
4
5
V
1)
100
Configurable Channels 4,5
8.1.4
Open load detection threshold voltage for VD(OL4,5) 3
Channel 4,5 in all configurations
8.1.5
Output diagnosis current channel 4,5 in
high side configuration
IL(DCHS)
100
200
300
µA
measured at VD(OL)
threshold
8.1.6
Output diagnosis current channel 4,5 in
low side configuration
IL(DCLS)
100
200
300
µA
measured at VD(OL)
threshold
4
5
V
1)
100
200
300
µA
measured at VOL
threshold
Low side Channels 6,7
8.1.7
Open load detection threshold voltage for VD(OL6,7) 3
Channel 6,7
8.1.8
Output diagnosis current channel 6,7
IL(DC6,7)
ON State Diagnosis (see also Protection in Chapter 7)
Over load detection current at channel
0,1,4,5,6,7
IL(OVL)
0.5
–
1.0
A
–
8.1.10 Over load detection current at channel
2,3
IL(OVL)
0.22
–
0.5
A
–
8.1.11 Over load detection delay time at all
channels
tOFF(OVL) –
–
60
µs
–
8.1.9
1) Open load detection voltages are referenced to ground
Data Sheet
24
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Diagnostic Features
8.2
Command Description
Diagnosis Registers (read only, register bank RB = 1)
DR01
00B
3
2
1
0
OL1
D1
OL0
D0
r
r
r
r
DR23
01B
3
2
1
0
OL3
D3
OL2
D2
r
r
r
r
DR45
10B
3
2
1
0
OL5
D5
OL4
D4
r
r
r
r
DR67
11B
3
2
1
0
OL7
D7
OL6
D6
r
r
r
r
Field
Bits
Type
Description
Dn
n = 7 to 0
2, 0
r
Diagnostic Feedback of Channel n
0
normal operation
1
over load or over temperature switch off occurred
OLn
n = 7 to 0
3, 1
r
Open Load Detection of Channel n
0
normal operation
1
Open load at OFF-state occurred
r/
CMD
Command Register
110B
3
2
1
0
Wake
STB
RST
CPL
r/w
r/w
r/w
r/w
Field
Bits
Type
Description
CPL
0
r/w
please refer to Section 7 for description
RST
1
r/w
please refer to Section 5.3 for description
STB
2
r/w
please refer to Section 5 for description
Wake
3
r/w
please refer to Section 5 for description
Data Sheet
25
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Diagnostic Features
Diagnosis Current Configuration Register
DCCR0
100B
3
2
1
0
DCEN3
DCEN2
DCEN1
DCEN0
r/w
r/w
r/w
r/w
DCCR1
101B
3
2
1
0
DCEN7
DCEN6
DCEN5
DCEN5
r/w
r/w
r/w
r/w
Field
Bits
Type
Description
DCENn
n = 7 to 0
3 to 0
r/w
Diagnosis Current Enable Channel n
0
Diagnosis current disabled
1
Diagnosis current enabled
Data Sheet
26
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
9
Serial Peripheral Interface (SPI)
The diagnosis and control interface is based on a serial peripheral interface (SPI).
The SPI is a full duplex synchronous serial slave interface, which uses four lines: SO, SI, SCLK and CS. Data is
transferred by the lines SI and SO at the data rate given by SCLK. The falling edge of CS indicates the beginning
of a data access. Data is sampled in on line SI at the falling edge of SCLK and shifted out on line SO at the rising
edge of SCLK. Each access must be terminated by a rising edge of CS. A modulo 8 counter ensures that data is
taken only, when a multiple of 8 bit has been transferred. The interface provides daisy chain capability.
SO
SI
CS
MSB
6
5
4
3
2
1
MSB
6
5
4
3
2
1
LSB
LSB
CS
SCLK
time
SPI.emf
Figure 8
Serial Peripheral Interface
The SPI protocol is described in Section 9.3. It is reset to the default values after reset.
9.1
SPI Signal Description
CS - Chip Select: The system micro controller selects the TLE7236SE by means of the CS pin. Whenever the pin
is in low state, data transfer can take place. When CS is in high state, any signals at the SCLK and SI pins are
ignored and SO is forced into a high impedance state.
CS High to Low transition:
•
•
The diagnosis information is transferred into the shift register.
SO changes from high impedance state to high or low state depending on the logic OR combination between
the transmission error flag (TER) and the signal level at pin SI. As a result, even in daisy chain configuration,
a high signal indicates a faulty transmission. For details, please refer to Figure 9. This information stays
available to the first rising edge of SCLK.
TER
SI
SO
1
OR
0
SI
SPI
SO
S
CS
SCLK
S
TER.emf
Figure 9
Data Sheet
Transmission Error Flag on SO Line
27
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
CS Low to High transition:
•
•
Command decoding is only done, when after the falling edge of CS exactly a multiple (1, 2, 3, …) of eight SCLK
signals have been detected. In case of faulty transmission, the transmission error flag (TER) is set and the
command is ignored.
Data from shift register is transferred into the input matrix register.
SCLK - Serial Clock: This input pin clocks the internal shift register. The serial input (SI) transfers data into the
shift register on the falling edge of SCLK while the serial output (SO) shifts diagnostic information out on the rising
edge of the serial clock. It is essential that the SCLK pin is in low state whenever chip select CS makes any
transition.
SI - Serial Input: Serial input data bits are shifted in at this pin, the most significant bit first. SI information is read
on the falling edge of SCLK. The 8 bit input data consist of two parts (control and data). Please refer to Section 9.3
for further information.
SO Serial Output: Data is shifted out serially at this pin, the most significant bit first. SO is in high impedance state
until the CS pin goes to low state. New data will appear at the SO pin following the rising edge of SCLK. Please
refer to Section 9.3 for further information.
9.2
Daisy Chain Capability
The SPI of TLE7236SE provides daisy chain capability. In this configuration several devices are activated by the
same CS signal MCS. The SI line of one device is connected with the SO line of another device (see Figure 10),
which builds a chain. The ends of the chain are connected with the output and input of the master device, MO and
MI respectively. The master device provides the master clock MCLK, which is connected to the SCLK line of each
device in the chain.
Figure 10
SO
SPI
SI
SO
SPI
SCLK
SI
device 3
CS
SCLK
MI
MCS
MCLK
SO
SPI
CS
SI
CS
MO
device 2
SCLK
device 1
SPI_DasyChain.emf
Daisy Chain Configuration
In the SPI block of each device, there is one shift register where one bit from SI line is shifted in each SCLK. The
bit shifted out can be seen at SO. After 8 SCLK cycles, the data transfer for one device has been finished. In single
chip configuration, the CS line must go high to make the device accept the transferred data. In daisy chain
configuration the data shifted out at device #1 has been shifted in to device #2. When using three devices in daisy
chain, three times 8 bits have to be shifted through the devices. After that, the MCS line must go high (see
Figure 11).
Data Sheet
28
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
MI
SO device 3
SO device 2
SO device 1
MO
SI device 3
SI device 2
SI device 1
MCS
MCLK
time
SPI_DasyChain2.emf
Figure 11
Data Transfer in Daisy Chain Configuration
9.3
SPI Protocol
The control and diagnosis function of the TLE7236SE is based on two register banks which are accessed via
following SPI protocol. The control register bank contains eight registers (with 4 bit each) addressed by a 3 bit
pointer. The diagnosis register bank contains four registers (with 4 bit each) addressed by a 2 bit pointer. An
additional indication bit is available to differentiate between standard diagnosis information and data read from a
register bank.
Control and Diagnosis Mode
CS1)
7
6
5
4
3
2
1
0
Write Register Command
SI
1
ADDR
DATA
Read Register Command
SI
0
ADDR
x
x
0
RB
Read Standard Diagnosis
SI
0
x
x
x
x
x
1
x
AWK
LH
D67
D45
D23
D01
Standard Diagnosis
S
O
TER
0
Second Frame of Read Command
S
O
TER
0
S
O
TER
1
1
ADDR (Diagnosis)
ADDR (Control)
DATA
DATA
1) This bit is valid between CS hi -> lo and first SCLK lo -> hi transition.
Note: Reading a register needs two SPI frames. In the first frame the RD command is sent. In the second frame,
the output at SPI signal SO will contain the requested information. Any command can be executed in the
second frame.
Data Sheet
29
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
Field
Bits
Type
TER
Description
Transmission Error
0
Previous transmission was successful (modulo 8 clocks
received)
1
Previous transmission failed or first transmission after reset
RB
0
Register Bank
0
CONTR Control Register Bank
1
DIAG Diagnosis Register Bank (read only)
ADDR
6:4
Address
Pointer to register for read and write command
DATA
3:0
Data
Data written to or read from register selected by address ADDR
Standard Diagnosis:
Field
Bits
AWK
5
Awake, Device active
LH
4
Limp home mode active
Dxy
3, 2, 1, 0
Failure mode alert of channel x and y (Overtemp, Overload)
OL
?
common open load flag for all channels
9.4
Type
Description
Register Overview
Control Register Bank
default1)
type
INX0
0H
r/w
INX3
INX2
0H
r/w
010B
INX5
INX4
0H
r/w
ICR67
011B
INX7
INX6
0H
r/w
DCCR0
100B
DCEN3
DCEN2
DCEN1
DCEN0
0H
r/w
DCCR1
101B
DCEN7
DCEN6
DCEN5
DCEN4
0H
r/w
Name
Addr
3
2
ICR01
000B
INX1
ICR23
001B
ICR45
1
0
2)
CMD
110B
WAKE
STB
RST
CPL
0H
w
unused
111B
–
–
–
–
0H
–
1) The default values are set after Vbb power-on, STB-command and RST-command
All command bits are cleared at the end of transmission, respectively after execution
2) CPL bit needs a valid next SPI communication frame to be cleared
Input word (see Chapter 6.6 for detailed description)
Name
State
1
0
INX0 - INX7
OFF
0
0
IN1
0
1
IN2 or IN3
1
0
ON
1
1
Data Sheet
30
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
Diagnosis Register Bank (read only)
Name
Addr
3
2
1
0
DR01
000B
OL1
D1
OL0
D0
DR23
001B
OL3
D3
OL2
D2
DR45
010B
OL5
D5
OL4
D4
DR67
011B
OL7
D7
OL6
D6
9.5
Timing Diagrams
tCS(lead)
tCS(lag)
tCS(td)
tSCLK(P)
CS
tSCLK(H)
0.7Vcc
0.2Vcc
tSCLK(L)
0.7Vcc
0.2Vcc
SCLK
tSI(su)
tSI(h)
0.7Vcc
SI
0.2Vcc
tSO(en)
tSO(v)
tSO(dis)
0.7Vcc
SO
0.2Vcc
SPI Timing.emf
Figure 12
Data Sheet
Timing Diagram
31
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
9.6
Electrical Characteristics
Unless otherwise specified: VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
typical values: VDD = 5.0 V, VBAT = 13.5 V, Tj = 25 °C
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min.
typ.
max.
0
–
0.2*VDD V
–
0.5*VDD –
VDD
V
–
5
40
90
µA
VCS = 0 V
VDD = 5 V
2.5
–
–
µA
1)
Input Characteristics (CS, SCLK, SI)
9.6.1 L level of pin
CS
SCLK
SI
9.6.2 H level of pin
CS
SCLK
SI
VCS(L)
VSCLK(L)
VSI(L)
9.6.3 L-input pull-up current through CS
VCS(H)
VSCLK(H)
VSI(H)
ICS(L)
9.6.4 H-input pull-up current through CS
ICS(H)
9.6.5 L-input pull-down current through pin ISCLK(L)
SCLK
ISI(L)
SI
9.6.6 H-input pull-down current through pin ISCLK(H)
SCLK
ISI(H)
SI
VDD = 5 V
VCS = 0.5*VDD
1.5
–
–
µA
1)
VDD = 5 V
VSCLK = VSI = 0.2*VDD
µA
10
40
80
0
–
0.4
VDD -
–
VDD
–
10
1)
VDD= 5 V
VSCLK = VSI = VDD
Output Characteristics (SO)
9.6.7 L level output voltage
9.6.8 H level output voltage
VSO(L)
VSO(H)
V
ISO = +2 mA
ISO = -1.5 mA
µA
VCS = VDD
0.4 V
9.6.9 Output tristate leakage current
ISO(OFF)
-10
Timings
fSCLK
tSCLK(P)
9.6.12 Serial clock high time
tSCLK(H)
9.6.13 Serial clock low time
tSCLK(L)
9.6.14 Enable lead time (falling CS to rising tCS(lead)
9.6.10 Serial clock frequency
0
–
5
MHz –
9.6.11 Serial clock period
200
–
–
ns
–
50
–
–
ns
1)
50
–
–
ns
1)
250
–
–
ns
1)
250
–
–
ns
1)
SCLK)
9.6.15 Enable lag time (falling SCLK to rising tCS(lag)
CS )
9.6.16 Transfer delay time (rising CS to
falling CS )
tCS(td)
250
–
–
ns
1)
9.6.17 Data setup time (required time SI to
falling SCLK)
tSI(su)
20
–
–
ns
1)
9.6.18 Data hold time (falling SCLK to SI)
tSI(h)
20
–
–
ns
1)
Data Sheet
32
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Serial Peripheral Interface (SPI)
Unless otherwise specified: VDD = 3.0 V to 5.5V, VBAT = 9.0 V to 16V, Tj = -40 °C to +150 °C
typical values: VDD = 5.0 V, VBAT = 13.5 V, Tj = 25 °C
Pos. Parameter
Symbol
Limit Values
Unit Test Conditions
min.
typ.
max.
9.6.19 Output enable time (falling CS to SO tSO(en)
valid)
–
–
200
ns
CL = 20 pF 1)
9.6.20 Output disable time (rising CS to SO tSO(dis)
tri-state)
–
–
200
ns
CL = 20 pF 1)
9.6.21 Output data valid time with capacitive tSO(v)
load
–
–
100
ns
CL = 20 pF 1)
1) Not subject to production test, specified by design.
Data Sheet
33
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Package Outlines
1.27
8˚
0.23 +0.09
2.65 MAX.
7.6 -0.2
8˚
0.1 20x
Seating Plane
9 x 1.27 = 11.43
0.35 +0.15 2)
0.35 x 45˚
1)
8˚ MAX.
0.05
8˚
0.2 -0.1
STAND OFF
1.1
2.45 -0.2
Package Outlines
0.2 -0.1
10
8˚
0.4 +0.8
10.3 ±0.3
0.2 20x
Ejector Mark
Depth 0.2 MAX.
20
11
1
10
1)
12.8 -0.2
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Does not include dambar protrusion per side
Figure 13
GPS05094
PG - DSO20-45 (Plastic Green Dual Small Outline Package)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pbfree finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.
Data Sheet
34
Dimensions in mm
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Application Information
11
Application Information
Note: The following information is given as a hint for the implementation of the device only and shall not be
regarded as a description or warranty of a certain functionality, condition or quality of the device.
Figure 14 shows a simplified application circuit. Vdd need to be externally reverse polarity protected.
Vbat
Lowside
Loads
C2
VDD
VBB
V DD
OUT0
OUT1
OUT2
PWM
IN1
PWM
IN2
LHO
LHI
OUT3
D1
D4
S4
D5
S5
CS
SCLK
SPI uC
SI
SO
OUT6
OUT7
GND
Highside
Loads
Application _LG.emf
Figure 14
Application Diagram
Note: This is a very simplified example of an application circuit. The function must be verified in the real application.
The circuit above shows a example of using this device in a automotive target application.
D1 is optional for loss of battery or loss of ground if no other circuit on this battery feed can limit the voltage to the
max. rating of the device (-40 V) .
C2 is for EMC and to stabilize the digital driver, recommended value is 47nF.
There are no resistors to the µC needed due to the internal reverse polarity protection.
For further information you may contact http://www.infineon.com/spider
Data Sheet
35
Rev. 1.0, 2010-02-18
SPI Driver for Enhanced Relay Control
TLE7236SE
Revision History
12
Revision History
Revision
Date
Changes
Rev. 1.0
2010-02-18
Datasheet released
Data Sheet
36
Rev. 1.0, 2010-02-18
Edition 2010-02-18
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2008 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.