Advanced Standard Products RadHard-by-Design RHD5964 Precision Voltage Reference www.aeroflex.com/RHDseries December 8, 2014 FEATURES Operating voltage range: 3 volts to 6 volts. Radiation performance - Total dose: - ELDRS Immune - SEL Immune - Neutron Displacement Damage > 1 Mrad(Si); Dose rate = 50 - 300 rads(Si)/s > 100 MeV-cm2/mg > 1014 neutrons/cm2 2.50V Precision Voltage Reference Power at 5 volts: 5mW 2000V Input/Output ESD protection Full military temperature range Designed for aerospace and high reliability space applications Packaging – Hermetic Ceramic Surface Mount - Weight - 2.0 gm max Aeroflex Plainview’s Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G. GENERAL DESCRIPTION Aeroflex’s RHD5964 is a radiation hardened, single supply, Voltage Reference in a 3-pad SMD-0.5 Packages. The RHD5964 design uses specific circuit topology and layout methods to mitigate total ionizing dose effects and single event latchup. These characteristics make the RHD5964 especially suited for the harsh environment encountered in Deep Space missions. It is guaranteed operational from -55°C to +125°C. Available screened in accordance with MIL-PRF-38534 Class K, the RHD5964 is ideal for demanding military and space applications. The RHD5964 integrated circuit die is mounted directly to the metal signal pad providing optimum thermal conduction to the printed circuit board bond sites. SCD5964 Rev A TABLE 1: ABSOLUTE MAXIMUM RATINGS Parameter Range Units Case Operating Temperature Range -55 to +125 °C Storage Temperature Range -65 to +150 °C Junction Temperature +150 °C Input Voltage VIN - GND +6.0 V VIN +0.4, GND -0.4 V Enable (EN) Lead Temperature (soldering, 10 seconds) 300 °C Thermal Resistance, Junction to Case,jc 3.5 °C/W 2,000 - 3,999 V ESD Rating (per MIL-STD-883, Method 3015, Class 2) NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress rating only; functional operation beyond the “Operation Conditions” is not recommended and extended exposure beyond the “Operation Conditions” may affect device reliability. TABLE 2: RECOMMENDED OPERATING CONDITIONS Symbol +VIN Parameter Typical Units Input Supply Voltage 3.0 to 5.0 V EN - High Output Enabled 70% VIN V EN - Low Output Disabled 30% VIN V TABLE 3: ELECTRICAL PERFORMANCE CHARACTERISTICS (TC = -55°C TO +125°C, +VIN = +5.0V, unless stated otherwise) RHD5964: 2.50V Precision Voltage Reference Parameter Symbol Quiescent Supply Current Conditions IINQ No Load VREF No Load Typ Max Units - .625 1 mA 2.45 2.5 2.55 V Reference Temperature Co 3/ REF TC - 25 35 ppm/°C Reference Change with Temperature 4/ REFT - 0.45 0.63 % Long Term Stability 5/ VREF/TIME - - 100 ppm Reference Output Voltage +25°C Min Power Supply Rejection Ratio PSRR 45 - - dB Reference Load Regulation REFIL IOUT = 0 -to- 1 mA - - 0.12 %/mA IO(SINK) Reference to VCC -25 -50 -75 mA IO(SOURCE) Reference to GND 25 50 75 mA - - 30 us Reference Short Circuit Current Switching Characteristics Turn on Time TON 5% Settling, No Load Notes: 1/ Specification derated to reflect Total Dose exposure to 1 Mrad(Si) @ +25°C. 2/ Not tested. Shall be guaranteed by design, characterization, or correlation to other test parameters. 3/ Reference temperature coefficient is defined as the absolute value of the difference from the maximum and minimum voltage over the specified temperature range, divided by the change in temperature and converted into ppm/°C. 4/ Reference change with temperature is defined as the absolute value of the difference from the maximum and minimum voltage over the specified temperature range represented as a percentage. 5/ Not tested. Shall be guaranteed to specified limits after 1000hr life test SCD5964 Rev A Advanced 12/8/14 2 Aeroflex Plainview FIGURE 1– VREF OUTPUT vs TEMPERATURE SCD5964 Rev A Advanced 12/8/14 3 Aeroflex Plainview RHD5964 SIGNAL DEFINITIONS Pad # .301 MAX Signal Definition 1 GND Ground 2 VREF 2.50V Precision Voltage Reference 3 VIN Input Voltage .095 2 Places R.025 MAX 6 Places .030 MIN 2 .405 MAX .005 .120 2 Places 3 .030 MIN 1 .225 .150 4X R.020 ESD symbol denotes Pin 1. .005 .005 .015 3 Places .286 .127 MAX NOTE: Package & Lid are electrically isolated from signal pads. FIGURE 2 – PACKAGE OUTLINE — SURFACE MOUNT : SMD-0.5 SCD5964 Rev A Advanced 12/8/14 4 Aeroflex Plainview ORDERING INFORMATION Model DLA SMD # Screening - Commercial Flow, +25°C testing only RHD5964-7 RHD5964-901-1S 5962H1422104KXC RHD5964-901-2S 5962H1422104KXA Package DLA SMD and Radiation Certification Pending 3-Pad SMD-0.5 Power Pkg EXPORT CONTROL: This product is controlled for export under the U.S. Department of Commerce (DoC). A license may be required prior to the export of this product from the United States. www.aeroflex.com/HiRel [email protected] Datasheet Definitions: Advanced Preliminary Datasheet Product in Development Shipping Non-Flight Prototypes Shipping QML and Reduced HiRel Aeroflex Plainview, Inc. reserves the right to make changes to any products and services described herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. SCD5964 Rev A Advanced 12/8/14 5 Our passion for performance is defined by three attributes. Solution-Minded Performance-Driven Customer-Focused