INFINEON ITS5215L

PROFET® ITS 5215L
Smart High-Side Power Switch
for Industrial Applications
Two Channels: 2 x 90mΩ
Status Feedback
Product Summary
Package
Operating Voltage
Vbb
Active channels
On-state Resistance
RON
Nominal load current
IL(NOM)
Current limitation
IL(SCr)
Operating Temperature
Ta
one
90mΩ
3.7A
12A
5.5...40V
two parallel
45mΩ
7.4A
12A
-30 … +85°C
PG-DSO-12
General Description
•
•
N channel vertical power MOSFET with charge pump, ground referenced CMOS compatible input and
diagnostic feedback, monolithically integrated in Smart SIPMOS technology.
Providing embedded protective functions
Applications
•
•
•
•
µC compatible high-side power switch with diagnostic feedback for 12V and 24V grounded loads in industrial
applications
All types of resistive, inductive and capacitve loads
Most suitable for loads with high inrush currents, so as lamps
Replaces electromechanical relays, fuses and discrete circuits
Basic Functions
•
•
•
•
•
•
•
Very low standby current
CMOS compatible input
Improved electromagnetic compatibility (EMC)
Fast demagnetization of inductive loads
Stable behaviour at undervoltage
Wide operating voltage range
Logic ground independent from load ground
Protection Functions
•
•
•
•
•
•
•
•
Block Diagram
Short circuit protection
Overload protection
Current limitation
Thermal shutdown
Overvoltage protection (including load dump) with external
resistor
Reverse battery protection with external resistor
Loss of ground and loss of Vbb protection
Electrostatic discharge protection (ESD)
Diagnostic Function
•
•
•
IN1
ST1
IN2
ST2
Logic
Channel 1
Channel 2
Load 1
Load 2
GND
Diagnostic feedback with open drain output
Open load detection in OFF-state
Feedback of thermal shutdown in ON-state
Infineon Technologies AG
Vbb
1
2006-Mar-27
PROFET® ITS 5215L
Functional diagram
GND
internal
voltage supply
current limit
gate
control
+
charge
pump
logic
VBB
clamp for
inductive load
OUT1
IN1
ST1
temperature
sensor
ESD
reverse
battery
protection
Open load
detection
channel 1
IN2
control and protection circuit
equivalent to
channel 1
ST2
OUT2
Pin Definitions and Functions
Pin
1
2
4
3
5
6,12,
heat
slug
Symbol
GND
IN1
IN2
ST1
ST2
Vbb
7,9,11
8
10
NC
OUT2
OUT1
Pin configuration
Function
Ground of chip
Input 1,2 activates channel 1,2 in case of logic
high signal
Diagnostic feedback 1 & 2 of channel 1,2
open drain, low on failure
Positive power supply voltage. Design the
wiring for the simultaneous max. short circuit
currents from channel 1 to 2 and also for low
thermal resistance
Not Connected
Output 1,2 protected high-side power output
of channel 1 and 2. Design the wiring for the
max. short circuit current
Infineon Technologies AG
2
(top view)
GND
IN1
ST1
IN2
ST2
Vbb
1•
2
3
4
5
6
Vbb
*
12
11
10
9
8
7
Vbb
NC
OUT1
NC
OUT2
NC
* heat slug
2006-Mar-27
PROFET® ITS 5215L
Maximum Ratings at Tj = 25°C unless otherwise specified
Parameter
Symbol
Supply voltage (overvoltage protection see page 5)
Supply voltage for full short circuit protection
Tj,start = -40 ...+150°C
Load current (Short-circuit current, see page 6)
Load dump protection1) VLoadDump = VA + Vs, VA = 13.5 V
RI2) = 2 Ω, td = 400 ms; IN = low or high,
each channel loaded with RL = 13.5 Ω,
Junction temperature
Operating temperature range
Storage temperature range
Power dissipation (DC)4)
Ta = 25°C:
(all channels active)
Ta = 85°C:
Maximal switchable inductance, single pulse
Vbb = 12V, Tj,start = 150°C4), see diagrams on page 9
one channel:
IL = 3.5 A, EAS = 178 mJ, 0 Ω
IL = 7.0 A, EAS = 337 mJ, 0 Ω
two parallel channels:
Electrostatic discharge capability (ESD)
IN:
(Human Body Model)
ST:
out to all other pins shorted:
Vbb
Vbb
IL
VLoad dump3)
Tj
Ta
Tstg
Ptot
ZL
VESD
Values
Unit
43
36
V
V
self-limited
60
A
V
+150
-30 ...+85
-40 … +105
°C
3.1
1.6
W
21.3
10
mH
1.0
4.0
8.0
kV
-10 ... +16
±0.3
±5.0
±5.0
V
mA
acc. MIL-STD883D, method 3015.7 and ESD assn. std. S5.1-1993
R=1.5kΩ; C=100pF
Input voltage (DC) see internal circuit diagram page 8
Current through input pin (DC)
Pulsed current through input pin5)
Current through status pin (DC)
1)
2)
3)
4)
5)
VIN
IIN
IINp
IST
Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended.
RI = internal resistance of the load dump test pulse generator
VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 13
only for testing
Infineon Technologies AG
3
2006-Mar-27
PROFET® ITS 5215L
Thermal Characteristics
Parameter and Conditions
Thermal resistance
junction - Case6)
junction – ambient6)
@ 6 cm2 cooling area
Symbol
each channel: RthjC
Rthja
one channel active:
all channels active:
min
Values
typ
max
Unit
5
----
K/W
Values
min
typ
max
Unit
-----
--45
40
Electrical Characteristics
Parameter and Conditions, each of the four channels
Symbol
at Tj = -40...+150°C, Vbb = 12 V unless otherwise specified
Load Switching Capabilities and Characteristics
On-state resistance (Vbb to OUT); IL = 2 A
each channel,
Tj = 25°C: RON
Tj = 150°C:
two parallel channels, Tj = 25°C:
----
70
140
35
90
180
45
mΩ
3.7
7.4
4.7
9.5
--
A
--
--
2
mA
---
100
100
250
270
µs
0.2
0.2
---
1.0
1.1
V/µs
V/µs
see diagram, page 10
Nominal load current
one channel active: IL(NOM)
two parallel channels active:
Device on PCB6), Ta = 85°C, Tj ≤ 150°C
Output current while GND disconnected or pulled up7); IL(GNDhigh)
Vbb = 32 V, VIN = 0,
see diagram page 8
Turn-on time8)
Turn-off time
RL = 12 Ω
Slew rate on 8)
Slew rate off 8)
6)
7)
8)
IN
IN
to 90% VOUT: ton
to 10% VOUT: toff
10 to 30% VOUT, RL = 12 Ω: dV/dton
70 to 40% VOUT, RL = 12 Ω: -dV/dtoff
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 13
not subject to production test, specified by design
See timing diagram on page 11.
Infineon Technologies AG
4
2006-Mar-27
PROFET® ITS 5215L
Parameter and Conditions, each of the four channels
Symbol
at Tj = -40...+150°C, Vbb = 12 V unless otherwise specified
Operating Parameters
Operating voltage
Undervoltage switch off9)
Unit
5.5
--41
---47
40
4.5
4.510)
52
V
V
-----
4.5
--1
10
15
µA
1010)
5
---
0.6
1.2
1.2
2.4
mA
Protection Functions14)
Current limit, Vout = 0V, (see timing diagrams, page 11)
Tj =-40°C: IL(lim)
Tj =25°C:
=+150°C:
Tj
--9
-15
--
23
A
----
Repetitive short circuit current limit,
Tj = Tjt
each channel IL(SCr)
two channels
---
12
12
---
A
--
2
--
ms
41
47
52
V
150
--
-10
---
°C
K
Overvoltage protection11)
I bb = 40 mA
Standby current12)
VIN = 0; see diagram page 11
Vbb(on)
Tj =-40°C...25°C: Vbb(u so)
Tj =125°C:
Vbb(AZ)
Values
min
typ
max
Tj =-40°C...25°C: Ibb(off)
Tj =150°C:
Tj =125°C:
Off-State output current (included in Ibb(off))
IL(off)
VIN = 0; each channel
Operating current 13), VIN = 5V,
one channel on: IGND
all channels on:
V
µA
(see timing diagrams, page 11)
Initial short circuit shutdown time
Vout = 0V
Tj,start =25°C: toff(SC)
(see timing diagrams on page 11)
Output clamp (inductive load switch off)15)
VON(CL)
at VON(CL) = Vbb - VOUT, IL= 40 mA
Thermal overload trip temperature
Thermal hysteresis
9)
10)
11)
12)
13)
14)
15)
Tjt
∆Tjt
is the voltage, where the device doesn´t change it´s switching condition for 15ms after the supply voltage
falling below the lower limit of Vbb(on)
not subject to production test, specified by design
Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended). See also VON(CL) in table of protection functions and
circuit diagram on page 8.
Measured with load; for the whole device; all channels off
Add IST, if IST > 0
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are
not designed for continuous repetitive operation.
If channels are connected in parallel, output clamp is usually accomplished by the channel with the lowest
VON(CL)
Infineon Technologies AG
5
2006-Mar-27
PROFET® ITS 5215L
Parameter and Conditions, each of the four channels
Symbol
at Tj = -40...+150°C, Vbb = 12 V unless otherwise specified
Reverse Battery
Reverse battery voltage 16)
Drain-source diode voltage (Vout > Vbb)
IL = - 2.0 A, Tj = +150°C
-Vbb
-VON
Values
min
typ
max
Unit
---
-600
32
--
V
mV
Diagnostic Characteristics
Open load detection voltage
V OUT(OL)
1.7
2.8
4.0
V
Input and Status Feedback17)
Input resistance
RI
2.5
4.0
6.0
kΩ
VIN(T+)
VIN(T-)
∆ VIN(T)
td(STon)
-1.0
---
--0.2
10
2.5
--20
V
V
V
µs
td(STon)
30
--
--
µs
td(SToff)
--
--
500
µs
td(SToff)
--
--
20
µs
IIN(off)
IIN(on)
5
10
-35
20
60
µA
µA
VST(high)
VST(low)
5.4
--
---
-0.6
V
1
(see circuit page 8)
Input turn-on threshold voltage
Input turn-off threshold voltage
Input threshold hysteresis
Status change after positive input slope18)
with open load
Status change after positive input slope18)
with overload
Status change after negative input slope
with open load
Status change after negative input slope18)
with overtemperature
Off state input current
VIN = 0.4 V:
On state input current
VIN = 5 V:
Status output (open drain)
Zener limit voltage
IST = +1.6 mA:
ST low voltage
IST = +1.6 mA:
16)
Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Power dissipation is higher compared to normal operating
conditions due to the voltage drop across the drain-source diode. The temperature protection is not active
during reverse current operation! Input and Status currents have to be limited (see max. ratings page 3 and
circuit page 8).
17) If ground resistors R
GND are used, add the voltage drop across these resistors.
18) not subject to production test, specified by design
Infineon Technologies AG
6
2006-Mar-27
PROFET® ITS 5215L
Truth Table
( each channel )
Normal operation
Open load
Overtemperature
L = "Low" Level
H = "High" Level
IN
L
H
L
H
OUT
L
H
Z
H
L
H
L
L
ST
H
H
L19)
H
H
L
X = don't care
Z = high impedance, potential depends on external circuit
Status signal valid after the time delay shown in the timing diagrams
Parallel switching of channel 1 and 2 is easily possible by connecting the inputs and outputs in parallel (see truth
table). If switching channel 1 to 2 in parallel, the status outputs ST1 and ST2 have to be configured as a 'Wired
OR' function with a single pull-up resistor.
Terms
Ibb
V
12,6
bb
I IN1
I IN2
V
IN1
V
IN2
V
2
4
I ST1
3
I ST2
5
Vbb
IN1
IN2
OUT1
10
I L1
8
I L2
PROFET
OUT2
ST1
ST2
V
ON1
V
ON2
Leadframe
GND
ST1 V ST2
V
1
I
R
GND
OUT1
V
OUT2
GND
Leadframe (Vbb) is connected to pin 6,12
External RGND optional; single resistor RGND = 150 Ω for reverse battery protection up to the max.
operating voltage.
19)
L, if potential at the Output exceeds the OpenLoad detection voltage
Infineon Technologies AG
7
2006-Mar-27
PROFET® ITS 5215L
Input circuit (ESD protection), IN1 or IN2
Overvolt. and reverse batt. protection
+ 5V
R
IN
I
+ Vbb
R ST
V
IN
ESD-ZD I
I
RI
I
Z2
Logic
GND
R ST ST
OUT
V
Z1
The use of ESD zener diodes as voltage clamp at DC
conditions is not recommended.
GND
R GND
Signal GND
Status output, ST1 or ST2
ST
Open-load detection, OUT1 or OUT2
ESDZD
GND
Load GND
VZ1 = 6.1 V typ., VZ2 = 47 V typ., RGND = 150 Ω,
RST= 15 kΩ, RI= 3.5 kΩ typ.
In case of reverse battery the load current has to be
limited by the load. Temperature protection is not
active
+5V
R ST(ON)
R Load
ESD-Zener diode: 6.1 V typ., max 0.3 mA; RST(ON) < 375 Ω
at 1.6 mA. The use of ESD zener diodes as voltage clamp at
DC conditions is not recommended.
OFF-state diagnostic condition:
Open Load, if VOUT > 3 V typ.; IN low
V
Inductive and overvoltage output clamp,
bb
R
EXT
OUT1 or OUT2
OFF
V
+Vbb
VZ
Logic
unit
V
OUT
Open load
detection
ON
OUT
Signal GND
GND disconnect
Power GND
VON clamped to VON(CL) = 47 V typ.
IN
Vbb
PROFET
OUT
ST
GND
V
bb
V
IN
V
ST
V
GND
Any kind of load. In case of IN = high is VOUT ≈ VIN - VIN(T+).
Due to VGND > 0, no VST = low signal available.
Infineon Technologies AG
8
2006-Mar-27
PROFET® ITS 5215L
GND disconnect with GND pull up
Inductive load switch-off energy
dissipation
E bb
IN
Vbb
E AS
PROFET
OUT
IN
ST
ELoad
Vbb
GND
PROFET
V
V
bb
V
IN ST
=
V
OUT
L
ST
GND
GND
ZL
{
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Due to VGND > 0, no VST = low signal available.
R
IN
2
While demagnetizing load inductance, the energy
dissipated in PROFET is
EAS= Ebb + EL - ER= ∫ VON(CL)·iL(t) dt,
with an approximate solution for RL > 0 Ω:
OUT
IL· L
EAS= 2·R (Vbb + |VOUT(CL)|)
ST
L
GND
V
L
EL = 1/2·L·I L
Vbb
PROFET
ER
Energy stored in load inductance:
Vbb disconnect with energized inductive
load
high
EL
ln (1+ |V
IL·RL
OUT(CL)|
)
Maximum allowable load inductance for
a single switch off (one channel)4)
bb
L = f (IL ); Tj,start = 150°C, Vbb = 12 V, RL = 0 Ω
For inductive load currents up to the limits defined by ZL
(max. ratings and diagram on page 9) each switch is
protected against loss of Vbb.
ZL [mH]
1000
Consider at your PCB layout that in the case of Vbb disconnection with energized inductive load all the load current
flows through the GND connection.
100
10
1
1
2
3
4
5
6
IL [A]
Infineon Technologies AG
9
2006-Mar-27
PROFET® ITS 5215L
Typ. on-state resistance
RON = f (Vbb,Tj ); IL = 2 A, IN = high
RON [mOhm]
Tj = 150°C
160
120
25°C
80
-40°C
40
0
5
7
9
11
30
40
Vbb [V]
Typ. standby current
Ibb(off) = f (Tj ); Vbb = 9...34 V, IN1,2 = low
Ibb(off) [µA]
45
40
35
30
25
20
15
10
5
0
-50
0
50
100
150
200
Tj [°C]
Infineon Technologies AG
10
2006-Mar-27
PROFET® ITS 5215L
Timing diagrams
Both channels are symmetric and consequently the diagrams are valid for channel 1 and
channel 2
Figure 2b: Switching a lamp:
Figure 1a: Vbb turn on:
IN1
IN
IN2
V bb
ST
V
OUT1
V
V
OUT
OUT2
ST1 open drain
I
L
ST2 open drain
t
t
Figure 3a: Turn on into short circuit:
shut down by overtemperature, restart by cooling
Figure 2a: Switching a resistive load,
turn-on/off time and slew rate definition:
IN1
IN
VOUT
I
other channel: normal operation
L1
90%
I
t on
dV/dton
10%
dV/dtoff
t
L(lim)
I
L(SCr)
off
t
ST
off(SC)
IL
t
t
Infineon Technologies AG
11
Heating up of the chip may require several milliseconds, depending
on external conditions
2006-Mar-27
PROFET® ITS 5215L
Figure 3b: Turn on into short circuit:
shut down by overtemperature, restart by cooling
(two parallel switched channels 1 and 2)
Figure 5a: Open load: detection in OFF-state, turn
on/off to open load
Open load of channel 1; other channels normal
operation
IN1/2
IN1
I
L1
+I
VOUT1
L2
2xIL(lim)
I L1
I
t
L(SCr)
ST
off(SC)
ST1/2
10µs
500µs
t
ST1 and ST2 have to be configured as a 'Wired OR' function
ST1/2 with a single pull-up resistor.
Figure 6a: Status change after, turn on/off to
overtemperature
Overtemperature of channel 1; other channels normal
operation
Figure 4a: Overtemperature:
Reset if Tj <Tjt
IN1
IN
ST
ST
30µs
20µs
V
OUT
T
J
t
Infineon Technologies AG
12
2006-Mar-27
PROFET® ITS 5215L
Package and Ordering Code
Published by
Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81669 München
© Infineon Technologies AG 2006
All Rights Reserved.
Standard: PG-DSO-12-2
Ordering Code
SP000219826
0.1
0.1 C 12x
Seating Plane
1
5× 1 = 5
0.4 +0.13
0.25
M
-0.035
0.25 +0.075
0.7 ±0.15
(0.2)
1.6 ±0.1
(1.8)
0.25 B
4.2 ±0.1
ø0.8 × 0.1 -0.05 Depth 4)
We hereby disclaim any and all warranties, including but not
limited to warranties of non-infringement, regarding circuits,
descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
1
6
7.8 ±0.1
Information
(Heatslug)
1)
Does not include
2)
Stand OFF
3)
Stand OUT
4)
The information herein is given to describe certain
components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
(4.4)
CAB
10.3 ±0.3
7
Attention please!
C
5.1 ±0.1
12
7.5 ±0.1 1)
8˚
5˚ ±3˚
B
2.6 max.
2)
0.8
8˚
0 +0.1
6.4 ±0.1 1)
A
2.35 ±0.1
(1.55)
ITS 5215L
0.1±0.05 3)
Sales Code
For further information on technology, delivery terms and
conditions and prices please contact your nearest Infineon
Technologies Office in Germany or our Infineon
Technologies Representatives worldwide (see address list).
plastic or metal protrusion of 0.15 max. per side
Pin 1 Index Marking; Polish finish
All package corners max. R 0.25
All dimensions in millimetres
Warnings
Due to technical requirements components may contain
dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies
Office.
Printed circuit board (FR4, 1.5mm thick, one layer
70µm, 6cm2 active heatsink area) as a reference for
max. power dissipation Ptot, nominal load current
IL(NOM) and thermal resistance Rthja
Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval
of Infineon Technologies, if a failure of such components can
reasonably be expected to cause the failure of that lifesupport device or system, or to affect the safety or
effectiveness of that device or system. Life support devices
or systems are intended to be implanted in the human body,
or to support and/or maintain and sustain and/or protect
human life. If they fail, it is reasonable to assume that the
health of the user or other persons may be endangered.
PG-DSO-12
Infineon Technologies AG
13
2006-Mar-27