ACTP-1506 Coaxial Tunnel Diode Detector Data Sheet Revision Date: 12/23/2015 The most important thing we build is trust DESCRIPTION: Superior performance and high reliability are designed into these detectors. They offer extremely stable output voltage over wide temperature excursions, typically +/-0.15dB from -65°C to +100°C at 1GHz and approx. +/-0.3dB at 18GHz. No bias is required for operation. Designs are available, in selected frequency bands, from 100MHz (or lower) to 18GHz. Typical output impedance is in the range of 95 to 125. This allows for fast pulsed video response and use in wide bandwidth requirements. Video bandwidths may be modified by selection of the RF bypass capacitor and load value. Square law typically ranges from TSS up to -17dBm. The upper limit can be raised as high as -13dBm with selected load values. The output polarity is usually negative but can be made positive if requested. SPECIFICATIONS: Parameter Specification Unit of Measure 8 – 18 GHz Sensitivity (min) 650 mV/mW Flatness vs. Frequency (max) 0.7 ±dB Typical TSS -50 dBm 2.3:1 Ratio 12 pF Frequency Range (min) Typical VSWR Nominal Video Capacitance OUTLINE DRAWING: FEATURES: • Contains hermetically sealed modules, internal RF matching, DC return, and RF bypass capacitor • Input impedance matching • Models may be chosen for broadband RF performance of for optimized narrow bands STANDARD CASE STYLE C3 (Optional Case Styles – C8, C15, C32) Revised Date: 12/23/2015 (732) 460-0212 www.cobham.com/CSCS 1 ACTP-1506 Coaxial Tunnel Diode Detector NOTES: ENVIRONMENTAL SPECIFICATIONS*: Maximum input power: +14 dBm (3 dB guardband for +17 dBm possible burnout) MIL-E-5400, MIL-STD-202, MIL-E-16400 Sensitivity is measured into an open circuit load (>10k ohm). Storage Temp: -65°C to +150°C Operating Temp: -55°C to +125°C VSWR is measured at or below -20 dBm input power level. Video capacitance is used for RF bypass. This value can be changed if required for video response time. Contact the factory for more information. SCREENING: Humidity: MIL-STD-202F, M103, Cond B Shock: MIL-STD-202F, M213, Cond B Altitude: MIL-STD-202F, M105, Cond B Vibration: MIL-STD-202F, M204, Cond B Thermal Shock: MIL-STD-202F, M107, Cond A * Compliant by design, verification optional Internal Visual per MIL-STD-883, Method 2017 Temperature Cycle: -65°C to +100°C, 10 cycles OPTIONAL HIGH-REL SCREENING (Ref MIL-PRF-38534): Stabilization Bake per MIL-STD-883, Method 1008 Temperature Cycle per MIL-STD-883, Method 1010 Constant Acceleration per MIL-STD-883, Method 2001 Burn-in per MIL-STD-883, Method 1015 Leak Test per MIL-STD-883, Method 1014 External Visual per MIL-STD-883, Method 2009 PART NUMBER ORDERING INFORMATION: Add desired polarity suffix: “N” for Negative, “P” for Positive (Ex: ACTP-1506N) Add desired case style suffix: “C3” (Ex: ACTP-1506NC3) Add “R” suffix: Reverse Connector Configuration (Ex: ACTP-1506NC3R) (SMA Female Input/SMA Male Output) Add “-RC” suffix: RoHS-compliant (Ex: ACTP-1506NZC3-RC) ISO 9001:2008 and AS9100 certified For further information please contact: Aeroflex Control Components, DBA Cobham Signal & Control Solutions (CSCS) reserves the right to make changes to any products and services herein at any time without notice. Consult CSCS or an authorized sales representative to verify that the information in this data sheet is current before using this product. CSCS does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by CSCS; nor does the purchase, lease, or use of a product or service from CSCS convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of CSCS or of third parties. Cobham Signal & Control Solutions 40 Industrial Way East Eatontown , NJ 07724 [USA] Phone: (732) 460-0212 Fax: (732) 460-0214 [email protected] Copyright 2015, Cobham Signal & Control Solutions. All rights reserved. Revised Date: 12/23/2015 (732) 460-0212 www.cobham.com/CSCS 2