Evaluation Board User Guide UG-046 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the AD1974 Four ADC with PLL 192 kHz, 24-Bit Codec EVAL-AD1974AZ PACKAGE CONTENTS interface board, EVAL-ADUSB2EBZ (also called USBi), connects to a PC USB port and provides SPI access to the evaluation board through a ribbon cable. A graphical user interface (GUI) program is provided for easy programming of the chip in a Microsoft® Windows® PC environment. The evaluation board allows demonstration and performance testing of most AD1974 features, including the four ADCs, as well as the digital audio ports. AD1974 evaluation board USBi control interface board USB cable OTHER SUPPORTING DOCUMENTATION AD1974 data sheet EVALUATION BOARD OVERVIEW Additional analog circuitry (ADC input filter/buffer) and digital interfaces such as S/PDIF are provided to ease product evaluation. This document explains the design and setup of the evaluation board for the AD1974. The evaluation board must be connected to an external ±12 V dc power supply and ground. On-board regulators derive the 3.3 V supplies for the AD1974. The AD1974 is controlled through an SPI interface. A small external All analog audio interfaces are accessible with stereo audio 3.5 mm TRS connectors. FUNCTIONAL BLOCK DIAGRAM POWER SUPPLY CONTROL INTERFACE SPI S/PDIF INTERFACE LRCLK, BCLK, SDATA ADC 1&2 ANALOG AUDIO AD1974 SERIAL AUDIO INTERFACES CLOCK & DATA ROUTING 08424-001 MCLK ROUTING Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 32 UG-046 Evaluation Board User Guide TABLE OF CONTENTS EVAL-AD1974AZ Package Contents ............................................ 1 Powering the Board.......................................................................3 Other Supporting Documentation ................................................. 1 Setting Up the Master Clock (MCLK)........................................4 Evaluation Board Overview ............................................................ 1 Configuring the PLL Filter ...........................................................5 Functional Block Diagram .............................................................. 1 Connecting Audio Cables ............................................................5 Revision History ............................................................................... 2 Switch and Jumper Settings .........................................................5 Setting Up the Evaluation Board .................................................... 3 Rotary and DIP Switch Settings ......................................................7 Standalone Mode .......................................................................... 3 Schematics and Artwork ..................................................................9 SPI control ..................................................................................... 3 CPLD Code ..................................................................................... 20 Automated Register Window Builder Software Installation .. 3 Ordering Information .................................................................... 26 Hardware Setup, USBi.................................................................. 3 Bill of Materials ........................................................................... 26 REVISION HISTORY 2/10—Revision 0: Initial Version Rev. 0 | Page 2 of 32 Evaluation Board User Guide UG-046 SETTING UP THE EVALUATION BOARD STANDALONE MODE It is possible to run the board and the AD1974 ADC in standalone mode, which fixes the functionality of the AD1974 into the I2S data format, running at 256 × fS (default register condition). The ADC BCLK and LRCLK ports are flipped between slave and master (input and output) by tying COUT (Pin 24) to low or high. This is accomplished by moving the J5 jumper to either 0 or SDA/1 (see Figure 2 and Figure 3 for the correct settings). 1. 2. 3. 4. 5. 08424-002 1 ADDR1 CLATCH 0 J8 CCLK ADDR0 0 SCL 1 J7 CIN 0 COUT 0 J6 SDA/1 J5 installation. To install the Automated Register Window Builder software, follow these steps: Figure 2. Standalone Slave Mode J5 J6 J7 J8 At www.analog.com/AD1974, find the Resources & Tools list. In the list, find Evaluation Boards & Development Kits and click Evaluation Boards/Tools to open the provided ARWBvXX.zip file. Double-click the provided .msi file to extract the files to an empty folder on your PC. Then double-click setup.exe and follow the prompts to install the Automated Register Window Builder. A computer restart is not required. Copy the .xml file for the AD1974 from the extraction folder into the C:\Program Files\Analog Devices Inc\AutomatedRegWin folder, if it does not appear in the folder after installation. To set up the USBi hardware, follow these steps: 08424-003 ADDR1 CLATCH 1 0 CCLK 0 SCL ADDR0 CIN 1 0 COUT 0 SDA/1 HARDWARE SETUP, USBi 1. Figure 3. Standalone Master Mode With the control jumpers set to standalone master mode, the S2 DIP switches set to on, the S3 DIP switch sets to off, and both rotary hex mode switches, S4 and S5, set to 0, the AD1974 is the LRCLK, BCLK, and SDATA source. The default MCLK jumper setting uses the on-board oscillator as MCLK for the AD1974 as well as the S/PDIF transmitter and HDR1 port. The board passes analog audio from the IN1 stereo to the S/PDIF and HDR1 output ports. IN2 can be selected by changing S3, Position 8, to on. Other serial audio clock and data routing configurations are described in the Switch and Jumper Settings section. SPI CONTROL The evaluation board can be configured for interactive control of the registers in the AD1974 by connecting the SPI port to the USBi. The SPI jumper settings are shown in Figure 4. 08424-004 ADDR1 CLATCH 1 0 J8 CCLK 0 SCL ADDR0 CIN J7 1 0 COUT 0 J6 SDA/1 J5 Figure 4. SPI Control The Automated Register Window Builder software controls the AD1974 and is available at www.analog.com/AD1974. AUTOMATED REGISTER WINDOW BUILDER SOFTWARE INSTALLATION The Automated Register Window Builder is a program that launches a graphical user interface for direct, live control of the AD1974 registers. The GUI content for the part is defined in a part-specific .xml file; this file is included in the software 2. 3. Plug the USBi ribbon cable into the J1 control interface header. Connect the USB cable to your computer and to the USBi. When prompted for drivers, follow these steps: a. Choose Install from a list or a specific location. b. Choose Search for the best driver in these locations. c. Check the box for Include this location in the search. d. Find the USBi driver in C:\Program Files\ Analog Devices Inc\AutomatedRegWin\USB drivers. e. Click Next. f. If prompted to choose a driver, select CyUSB.sys. g. If the PC is running Windows XP and you receive a message that the software has not passed Windows logo testing, click Continue Anyway. You can now open the Automated Register Window Builder application and load the .xml file for the part onto your evaluation board. POWERING THE BOARD The AD1974 evaluation board requires power supply input of ±12 V dc and ground to the three binding posts; +12 V draws ~250 mA and −12 V draws~100mA. The on-board regulators provide two 3.3 V rails, one each for AVDD and DVDD for the AD1974. DVDD also supplies power for the active peripheral components on the board. Jumpers are provided to allow access to the power connections of the AD1974. These are convenient points to insert a current measuring device. The only components on the AD1974 side of the jumper are the part itself and the local power supply decoupling. The jumper blocks are shown in Figure 5. Rev. 0 | Page 3 of 32 UG-046 Evaluation Board User Guide C158 R166 R172 JP24 C170 R178 R156 08424-008 R156 C154 R155 R178 R175 EXT CLK IN JP30 HDR2 JP31 HDR1 08424-009 J23 U22 JP28 JP29 8416 R156 C154 R155 C153 R172 193X_MCLKO MCLKO BUS R166 JP24 R169 JP27 MCLKI BUS C168 R167 EXT CLK J23 U18 J22 Y1 JP23 CPLD U21 JP25 HDR2 OSC DISABLE HDR1 R178 R174 OSC C158 08424-007 MCLKI BUS L7 U22 JP28 EXT CLK JP20 MCLKO C147 XTAL R174 C168 C170 R175 EXT CLK IN 08424-010 R169 JP27 OSC DISABLE HDR1 JP31 HDR1 JP31 HDR1 R160 JP22 J22 193X_MCLKO MCLKO BUS R166 JP24 R167 EXT CLK IN C170 JP30 HDR2 1938_MCLKI Y1 JP23 CPLD U21 JP25 HDR2 JP30 HDR2 U18 R175 C168 193X_MCLKI DISABLE R156 C154 R155 MCLKI XTAL C158 JP29 8416 JP29 8416 JP19 C153 OSC R160 JP22 L7 U22 R174 JP18 193X_MCLKI DISABLE 1938_MCLKI J23 Figure 9. Passive Crystal; the AD1974 Is Master; the CPLD Is Slave from the MCLKO Port Figure 6. Active On-Board Oscillator as Master; the AD1974 and CPLD as Slaves JP20 MCLKO C147 XTAL 193X_MCLKO MCLKO BUS R166 JP31 HDR1 JP19 R172 JP28 EXT CLK IN C170 JP18 R169 JP27 EXT CLK R175 C168 JP30 HDR2 R167 OSC DISABLE HDR1 J23 U18 J22 Y1 JP23 CPLD U21 JP25 HDR2 MCLKI BUS R174 C153 OSC C158 08424-006 MCLKI BUS R160 JP22 L7 U22 JP28 CLK JP20 MCLKO C147 XTAL R178 R172 JP29 8416 JP31 HDR1 193X_MCLKI DISABLE J22 MCLKO BUS R169 JP27 OSC DISABLE HDR1 EXT CLK IN C170 JP30 HDR2 JP18 193X_MCLKO R178 R166 JP24 R167 R175 C168 The MCLK configurations shown in Figure 9 and Figure 10 use the AD1974 MCLKO port to drive the CPLD and, possibly, the HDRs. The passive crystal runs the AD1974 at 12.288 MHz. Figure 10 shows the MCLKI shut off; this is the case when the PLL is set to LRCLK instead of to MCLK. Y1 JP23 CPLD U21 JP25 HDR2 EXT JP29 8416 MCLKI XTAL C158 U18 J23 Figure 8. External Clock In as Master; the AD1974 and CPLD as Slaves R156 C154 R155 MCLKI XTAL C153 OSC L7 R174 1938_MCLKI JP20 MCLKO C147 XTAL 193X_MCLKO U22 JP28 JP19 1938_MCLKI R160 JP22 R172 EXT CLK 193X_MCLKI DISABLE JP19 R169 JP27 MCLKI XTAL Note that, if the HDR connectors are to be driven with MCLK from a source on the evaluation board, SW2 and/or SW3 must be switched from the IN position to the OUT position. R167 OSC DISABLE HDR1 MCLKI BUS The AD1974 evaluation board has a series of jumpers that give the user great flexibility in the MCLK clock source for the AD1974. MCLK can come from five sources: passive crystal, active oscillator, external clock in, and two header connections. Note that the CPLD on the board must have a valid clock source; the frequency is not critical. These jumper blocks can assign this CPLD clock. Most applications of the board use MCLK from either the oscillator or one of the header (HDR) inputs. Figure 6 to Figure 7 show the on-board active oscillator disabled so that it does not interfere with the selected clock. The clock feed to the CPLD comes directly from the clock source. Y1 JP23 CPLD U21 JP25 HDR2 JP24 SETTING UP THE MASTER CLOCK (MCLK) U18 J22 MCLKO BUS R160 JP22 L7 C153 1938_MCLKI Figure 5. AD1974 Power Jumpers JP18 JP20 MCLKO C147 XTAL C154 R155 JP19 OSC JP7 JP18 08424-005 JP5 JP6 MCLKI XTAL 193X_MCLKI DISABLE DVDD AVDD1 AVDD2 POWER SELECTION Figure 10. LRCLK Is the Master Clock Using the PLL; MCLKI Is Disabled, and CPLD Is Slave to the MCLKO Port Figure 7. HDR1 as MCLK Master; the AD1974, CPLD, and HDR2 as Slaves Rev. 0 | Page 4 of 32 Evaluation Board User Guide UG-046 JP15 C131 MCLK LRCLK C114 FILTER CM GND JP4 C89 C88 R107 C74 VREF SELECT TP32 C83 C82 R106 R76 C68 JP12 JP11 C77 R81 R79R77C62 R86 C76 S1 IN1L– TP28 R90 C72 C80 U14 C99 IN1R+ IN1R– TP34 Figure 13. VREF Selection and DC Coupling Jumpers Digital Audio 08424-012 JP15 C131 C75 IN1R PLL SELECT C120 C125 R138 R85 R87 Figure 11. MCLK Loop Filter Selected R129 C66 C69 R84 IN1L+ 08424-013 R138 C67 U12 TP25 TP30 TP26 C65 C64 C105 C125 C61 R93 R97 C79 MCLK LRCLK PLL SELECT C120 IN1L 08424-011 C114 The PLL for the AD1974 can run from either MCLK or LRCLK, according to its setting in the PLL and Clock Control 0 register, Bits[6:5]. The matching RC loop filter must be connected to LF (Pin 47) using JP15. See Figure 11 and Figure 12 for the jumper positions. R129 C63 C60 R101 R73 R72 JP13 CONFIGURING THE PLL FILTER Figure 12. LRCLK Loop Filter Selected Normally, the MCLK filter is the default selection; it is also possible to use the register control window to program the PLL to run from the LRCLK. In this case, the jumper must be changed as shown in Figure 12. CONNECTING AUDIO CABLES There are two types of digital interfacing, S/PDIF and discrete serial. The S/PDIF transmitter port has both optical and coaxial connectors that can be used simultaneously. The serial audio connectors use 1 × 2 100 mil spaced headers, signal and ground. The LRCLK, BCLK, and SDATA paths are available for the ADC on the HDR1 and HDR2 connectors. Each has a connection for MCLK; each HDR MCLK interface has a switch to set the port as an input or output, depending on the configuration of the evaluation board. SWITCH AND JUMPER SETTINGS Analog Audio The analog inputs and outputs use 3.5 mm TRS jacks; they are configured in the standard configuration: tip = left, ring = right, sleeve = ground. The analog inputs to IN1 and IN2 generate 0 dBFS from a 1 V rms analog signal. The on-board buffer circuit creates the differential signal to drive the ADC with 2 V rms at the maximum level. There are test points that allow direct access to the ADC pins; note that the ADC pins have a common mode voltage of 1.5 V dc. These test points require proper care so that improper loading does not drag down the common-mode voltage, and the headroom and performance of the part do not suffer. The ADC buffer circuit has been designed with a switch (S1) that allows the user to change the voltage reference for all of the amplifiers. GND, CM and FILTR can be selected as a reference; it is advisable to shut down the power to the board before changing this switch. The CM and FILTR lines are very sensitive and do not react well to a change in load while the AD1974 is active. A series of jumpers allows the user to dccouple the buffer circuit to the ADC analog port in when CM and FILTR are selected (see Figure 13). Clock and Control The AD1974 is designed to run in standalone mode at a sample rate (fS).of 48 kHz, with an MCLK of 12.288 MHz (256 × fS). In standalone slave mode, the ADC port must receive valid BCLK and LRCLK. The AD1974 can be clocked from the HDR1 connector; the ADC BCLK and LRCK port sources are selected with S2, Position 2 and Position 3. For HDR1 as master, S2, Position 3, should be on (see the detail in Figure 14 and Figure 15). Note that HDR2 is not implemented in the CPLD routing code. It is also possible to configure the AD1974 ADC BCLK and LRCK ports to run in standalone master mode; moving J5 to SDA/1, as shown in Figure 3, changes the state of the AD1974. Setting S2, Position 2, to on selects the proper routing to both the S/PDIF transmitter and the HDR1 connector. In this mode, the AD1974 ADC port generates BCLK and LRCLK when given a valid MCLK. For the full flexibility of the AD1974, the part can be put in SPI control mode and programmed with the Automated Register Window Builder application (see Figure 4 for the appropriate jumper settings). Changing the registers and setting the DIP switches allow many possible configurations. In the various master and slave modes, the AD1974 takes MCLK from a selected source and can be set to generate or receive either BCLK or LRCLK to or from either the ADC or the DAC port, depending on the settings and requirements. Rev. 0 | Page 5 of 32 UG-046 Evaluation Board User Guide As an example, to set the ADC port as master, switch the ADC Control Register 2 bits for BCLK and LRCLK to master and change S2, Position 2, and S2, Position 5, to on. In this mode, the board is configured so that the ADC BCLK and LRCLK pins are the clock source for both the ADC destination and the DAC data source. For the DAC port to be the master, the DAC Control Register 1 bits for BCLK and LRCLK must be changed to master, and S2, Position 2 and Position 3, and S2, Position 5 and Position 6, must all be on. On this evaluation board, these settings allow the master port on the AD1974 to drive both the S/PDIF and the HDR connections. Many combinations of master and slave are possible (see Figure 14 and Figure 15 for the correct settings). S/PDIF Audio The settings in Figure 14 and Figure 15 show the details of clock routing and control for the ADC port. The board is shipped with the IN1 analog port selected as default feed to the S/PDIF transmitter; the hex switches are set to 0 and only the S2, Position 2, DIP switch is on. All other switches are set to off. The evaluation board is shipped in standalone master mode (see Figure 3); the BCLK and LRCLK signals run from the ADC port of the AD1974 to the S/PDIF transmitter and HDR1. In this default configuration, IN1 analog is routed through the AD1974 ADC ASDATA1 path to the S/PDIF output. By changing DIP switch S3, Position 8, from 0 to 1, IN2 is selected. HDR Connectors—Serial Audio Routing of serial audio to the HDR1 connector is controlled by DIP S3, Position 6 and Position 7. The default condition routes IN1 to ASDATA1 and IN2 to ASDATA2. Other Options To use other fS rates, the USBi must be connected and the AD1974 registers must be programmed accordingly. For example, adjusting the fS rate to 96 kHz requires that the ADC Control 0 register have the sample rate set to 96 kHz (see Figure 14 and Figure 15 for the complete list of options). The CPLD code is presented in the CPLD Code section and is included with the evaluation board; alterations and additions to the functionality of the CPLD are possible by altering the code and reprogramming the CPLD. Rev. 0 | Page 6 of 32 Figure 14. Settings Chart 1 Rev. 0 | Page 7 of 32 Description SPDIF_TX_RX RESETB SPDIF_RX_TX in active mode SPDIF_RX_TX in reset mode Position-8 SPDIF_RX_TX /RESET Off* On SPDIF TX - CS8406 Jumpers JP18 0 = the V pin input determines the s tate of the v alidity bit in the outgoing AES3 transmitted data 1 = the V pin input determines the s tate of the v alidity bit in the outgoing AES3 transmitted data JP2 0 = NVERR selected 1 = RERR selected Description SPDIF_RX_TX MCLK Rate SPDIF_RX_TX MCLK Rate = 256xfS SPDIF_RX_TX MCLK Rate = 128xfS Position-7 SPDIF_RX-TX Clock Rate Selection Off* On SPDIF RX - CS8416 Jumpers JP1 0 = Normal update rate phase detector, increased clock jitter 1 = High update rate phase detector, low clock jitter DBCLK Source SPDIF_RX_8416 HDR1_DBCLK ADC-ABCLK DAC-DBCLK Position-5 Position-6 DAC - DBCL K, DLRCLK Source Selection Off* Off* Off On On Off On On DLRCLK Source SPDIF_RX_8416 HDR1_DLRCLK ADC-ALRCLK DAC-DLRCLK Enable DAC clocks Tristate DAC clocks Description ALRCLK Source SPDIF_RX_8416 HDR1_ALRCLK ADC-ALRCLK DAC-DLRCLK Position-4 DAC – DBCLK, DLRCLK Clock Disable Off* Enable On Disable Position-2 Position-3 ADC - ABCL K, ALRCLK Source Selection Off* Off* Off On On Off On On ABCLK Source SPDIF_RX_8416 HDR1_ABCLK ADC-ABCLK DAC-DBCLK Enable ADC clocks Tristate ADC clocks Off* On Enable Disable Description DIP Switch S2 position: Position-1 ADC- ABCLK, ALRCLK Clock Disable SPDIF_Tx Clocks Slave Slave Slave Slave SPDIF_Tx Clocks Slave Slave Slave Slave HDR1 Clocks Slave Master Slave Slave HDR1 Clocks Slave Master Slave Slave ADC Cl ocks N/A N/A Master N/A ADC Cl ocks Slave Slave Master Slave SPDIF_TX CS8406 MCLK Rate Jumper Settings JP10 JP9 0 0 0 1 JP3 0 = Emphasis audio match off 1 = Emphasis audio match on SPDIF_TX MCLK Rate = 256xfS SPDIF_TX MCLK Rate = 128xfS (Note: This position must be toggled after power-up for proper operation.) SPDIF_TX CS8406 MCLK Jumper Settings JP10 JP9 0 0 0 1 SPDIF_Rx Clocks Master Slave Slave Slave SPDIF_Rx Clocks Master Slave Slave Slave 1) DIP Switch S2 controls the AD1974 ADC a nd DAC serial clock source selection. One of four clock sources is selected based on the setting. SPDIF Receiver CS8416, Header Connector HDR1, ADC serial clocks, or DAC serial clock can be the clock source. ADC a nd DAC serial clock selection is controlled independently. 2) The AD1974 master clock source should be selected using the JP28, JP29, JP30, and JP31 header jumpers such that the MCLK source is in sync with the DAC/ADC serial clock and data source. ADC and DAC Serial Clock (BCLK, LRCLK) Source Selection and Routing (Switch S2) 1) DIP Switch S2 Position-8 (SPDIF_RX_TX reset) must be toggled after power-up for proper operation of the SPDIF receiver and transmitter. 2) The AD1974 evalution board defaults the AD1974 codec to standalone mode preventing SPI/I2C operation. The J5, J6, J7, and J8 he ader jumpers can be changed for SPI/I2C operation. AD1974/ADAU132X Rev-E Evaluation Board Configuration: (* indicates default setting) DAC Clocks Slave Slave Slave Master DAC Clocks N/A N/A N/A Master Evaluation Board User Guide UG-046 ROTARY AND DIP SWITCH SETTINGS 08424-014 SPDIF_RX_8416 HDR1_DSDATA2 SPDIF_RX_8416 HDR1_DSDATA2 HDR1_DSDATA2 N/A N/A ZERO DATA HDR1_DSDATA1 HDR1_DSDATA2 DAC_TDM_OUT DAC_TDM_OUT Aux ADC1 input TRISTATE SPDIF_RX_8416 SPDIF_RX_8416 HDR1_DSDATA1 HDR1_DSDATA1 HDR1_DSDATA1 N/A N/A ZERO DATA HDR1_DSDATA1 HDR1_DSDATA1 HDR1_DSDATA1 HDR1_DSDATA1 HDR1_DSDATA1 TRISTATE Stereo Stereo Stereo Stereo Stereo N/A N/A Stereo/TDM Stereo Stereo TDM Dual- Line TDM DAC aux mode Stereo/TDM TRISTATE DAC_TDM_OUT Aux DAC2 output HDR1_DSDATA3 Aux ADC2 input TRISTATE SPDIF_RX_8416 HDR1_DSDATA4 HDR1_DSDATA4 HDR1_DSDATA4 SPDIF_RX_8416 N/A N/A ZERO DATA HDR1_DSDATA1 HDR1_DSDATA4 SPDIF_RX_8416 HDR1_DSDATA3 HDR1_DSDATA3 SPDIF_RX_8416 HDR1_DSDATA3 N/A N/A ZERO DATA HDR1_DSDATA1 HDR1_DSDATA3 0* 1 2 3 4 5 6 7 8 9 A B C D E F Figure 15. Settings Chart 2 Rev. 0 | Page 8 of 32 Input Input Input Output Output Input TRISTATE Input Input Input Input Input Input TRISTATE Position-7 Off* On Off On ADC Serial Format Stereo Stereo TDM ADC Aux (see note) HDR1_ ASDATA1 ASDATA1 ASDATA2 ASDATA1 ASDATA1 TRISTATE Output Output Input Input TRISTATE Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input HDR1_ ASDATA1 Output Output Output Output HDR1_ ASDATA2 Output Output Input Input DIP Switch S3 Position: Position-8 Off* ADC1 Data Stream ASDATA1 is sourced to the SPDIF_Tx_8406. On ADC2 Data Stream ASDATA2 is sourced to the SPDIF_Tx_8406. DIP Switch S3 Position: Position-6 Position-7 Off* Off* Off On On Off On On NOTE: ADC A UX mode overrides the DAC data configuration rotary Switch S2 setting. Position-6 Off* Off On On DIP Switch S3 Position: Input Input Input Input Input Input Input Input Input Input ADC1 (ASDATA1) Output Output Output Output HDR1_ ASDATA2 ASDATA2 ASDATA2 ADC TDM input stream ADC TDM input stream Output Input Input Input Input Input N/A N/A Input Input Input ***** Column content indicates the direction of the DAC data pins and corresponding HDR1 connector DAC data pins ******* DAC2 (DSDATA2) DAC3 (DSDATA3) DAC4 (DSDATA4) HDR 1_DSDATA1 S4 Position DAC1 (DSDATA1) 0* 1 2 3 4 5 6 7 8 9 A B C D E F ***** Signal sources to the DAC data lines (DSDATA1/2/3/4) fill the columns, column header is the destination ****** S4 Position DAC Serial Format DAC1 (DSDATA1) DAC2 (DSDATA2) DAC3 (DSDATA3) DAC4 (DSDATA4) Input Input Output Input Input N/A Input Input N/A Input HDR 1_DSDATA3 Output Output Output Input Input N/A Input Input Input N/A HDR 1_DSDATA4 N/A Master Master Master Master Master SPDIF_Rx Data N/A Master Master Master Master Master HDR 1 Data ADC2 (ASDATA2) Output Output Input Input Description (HDR1 ADC Data Source Selection) HDR1 Connector ADC Data Lines ASDATA1 and ASDATA2 receive corresponding ADC data stream HDR1 Connector ADC Data Line ASDATA1 receive ADC2 data line ASDATA2 HDR1 Connector ADC Data Line ASDATA1 receive ADC TDM out data stream HDR1 Connector ADC Data Line ASDATA1 receive ADC TDM out data stream Output Input Input Output Output Input N/A Input N/A Input Input HDR 1_DSDATA2 Tristate all DAC data lines, DSDATA1, DSDATA2, DSDATA3, and DSDATA4 Source zero data to all eight DAC channels HDR1 Connector Signal HDR1_D SDATA1 drives all four DAC pairs HDR1 Connector Data Lines DSDATA1, DSDATA2... so on drive corresponding DAC data lines HDR1 Connector Data Lines DSDATA1, DSDATA2... so on drive/receive corresponding DAC data lines in TDM mode HDR1 Connector Data Lines DSDATA1, DSDATA2... so on drive/receive corresponding DAC data lines in TDM mode HDR1 Connector Data Lines DSDATA1, DSDATA2... so on drive/receive corresponding DAC data lines in TDM mode SPDIF_RX_8416 stereo data to all eight DAC channels SPDIF_RX_8416 stereo data to DAC1 only, rest DACs2/3/4 data from HDR1 connector SPDIF_RX_8416 data to DAC2 only, rest DACs1/3/4 data from HDR1 connector SPDIF_RX_8416 data to DAC3 only, rest DACs1/2/4 data from HDR1 connector SPDIF_RX_8416 data to DAC4 only, rest DACs1/2/3 data from HDR1 connector Description 08424-015 Rotary hex Switch S4 selects the AD1974 DAC serial data source. The DAC data source can be either SPDIF Receiver CS8416 or can be provided by the Header Connector HDR1. It is important to note that the DAC data source should be in sync with the DAC serial port clock source( set by DIP Switch S2, Positions [5:6]. DIP Switch S3 routes the ADC serial data among AD193x, SPDIF Transmitter CS8406, and Header Connector HDR1 in stereo, TDM, and aux mode. DAC and ADC Se rial Data (DSDATA/ASDATA) Source Selection and Routing (Switch S4 and S witch S3) UG-046 Evaluation Board User Guide Evaluation Board User Guide UG-046 SCHEMATICS AND ARTWORK 08424-016 Figure 16. Board Schematics, Page 1—ADC Buffer Circuits Rev. 0 | Page 9 of 32 UG-046 Evaluation Board User Guide 08424-017 Figure 17. Board Schematics, Page 2—Serial Digital Audio Interface Headers with MCLK Direction Switching Rev. 0 | Page 10 of 32 Evaluation Board User Guide UG-046 08424-018 Figure 18. Board Schematics, Page 3—S/PDIF Receive and Transmit Interfaces Rev. 0 | Page 11 of 32 UG-046 Evaluation Board User Guide 08424-019 Figure 19. Board Schematics, Page 4—Serial Digital Audio Routing and Control CPLD Rev. 0 | Page 12 of 32 Evaluation Board User Guide UG-046 08424-020 Figure 20. Board Schematic, Page 5—AD1974 with MCLK Selection Jumpers Rev. 0 | Page 13 of 32 Evaluation Board User Guide 08424-021 UG-046 Figure 21. Board Schematics, Page 6—Daughter Card Interface, Useful as Test Points Rev. 0 | Page 14 of 32 Evaluation Board User Guide UG-046 08424-022 Figure 22. Board Schematics, Page 7—DAC Buffer Circuits Rev. 0 | Page 15 of 32 UG-046 Evaluation Board User Guide 08424-023 Figure 23. Board Schematics, Page 8—SPI Control Interface Rev. 0 | Page 16 of 32 UG-046 08424-024 Evaluation Board User Guide Figure 24. Board Schematics, Page 9—Power Supply Rev. 0 | Page 17 of 32 Evaluation Board User Guide 08424-025 UG-046 Figure 25. Top Assembly Layer Rev. 0 | Page 18 of 32 UG-046 08424-026 Evaluation Board User Guide Figure 26. Bottom Assembly Layer Rev. 0 | Page 19 of 32 UG-046 Evaluation Board User Guide CPLD CODE MODULE TITLE IF_Logic 'AD1974 EVB Input Interface Logic' //=================================================================================== // FILE: // REVISION DATE: AD1974_pld_revE.abl // REVISION: // DESCRIPTION: 04-16-09 (rev-E) E //=================================================================================== LIBRARY 'MACH'; "INPUTS ---------------------------------------------------------------------------- // AD1974 CODEC pins DSDATA1,DSDATA2 pin 86, 87 istype 'com'; DSDATA3,DSDATA4 pin 91, 92 istype 'com'; DBCLK,DLRCLK pin 85, 84 istype 'com'; ASDATA1,ASDATA2 pin 80, 81 istype 'com'; ABCLK,ALRCLK pin 78, 79 istype 'com'; // 25-pin header connector HDR1 pins HDR1_DSDATA1 pin 20 istype 'com'; HDR1_DSDATA2 pin 19 istype 'com'; HDR1_DSDATA3 pin 17 istype 'com'; HDR1_DSDATA4 pin 16 istype 'com'; HDR1_DBCLK pin 21 istype 'com'; HDR1_DLRCLK pin 22 istype 'com'; HDR1_ASDATA1 pin 29 istype 'com, buffer'; HDR1_ASDATA2 pin 28 istype 'com, buffer'; HDR1_ABCLK pin 30 istype 'com'; HDR1_ALRCLK pin 31 istype 'com'; // 25-pin header connector HDR2 pins HDR2_DSDATA1 pin HDR2_DSDATA2 pin 36 istype 'com'; 37 istype 'com'; HDR2_DSDATA3 pin 35 istype 'com'; HDR2_DSDATA4 pin 34 istype 'com'; HDR2_DBCLK pin 41 istype 'com'; HDR2_DLRCLK pin 42 istype 'com'; HDR2_ASDATA1 pin 44 istype 'com'; HDR2_ASDATA2 pin 43 istype 'com, buffer'; HDR2_ABCLK pin 47 istype 'com'; HDR2_ALRCLK pin 48 istype 'com'; // S/PDIF Rx CS8414 pins SDATA_8416 pin 61 istype 'com'; Rev. 0 | Page 20 of 32 Evaluation Board User Guide UG-046 BCLK_8416 pin 60 istype 'com'; LRCLK_8416 pin 59 istype 'com'; SOMS_RX,SFSEL1_RX,SFSEL0_RX,RMCKF_RX pin 66,67,64,65 istype 'com'; // S/PDIF Tx CS8404 pins SDATA_8406 'com'; pin 50 istype BCLK_8406,LRCLK_8406 pin 53, 54 istype 'com'; MCLK_8406 'com'; pin 49 istype APMS_TX,SFMT1_TX,SFMT0_TX pin 55,56,58 istype 'com'; CPLD_MCLK 'com'; pin 89 istype // AD1974 SPI port pins //CCLK,CDATA,CLATCH pin 84, 83, 85 istype 'com'; //COUT pin 82 istype 'com'; //CLATCH2,CLATCH3,CLATCH4 pin 86, 56, 4 istype 'com'; //CONTROL_ENB 'com'; pin 81 istype S/PDIF_RESET_OUT 'com'; pin 69 istype // Switch S1, S2, S3 and S4 pins ADC_CLK_OFF 'com'; pin 93 istype // S2-1 ADC_CLK_SRC1 pin 94 istype 'com'; // S2-2 ADC_CLK_SRC0 pin 97 istype 'com'; // S2-3 DAC_CLK_OFF 'com'; pin 98 istype // S2-4 DAC_CLK_SRC1 pin 99 istype 'com'; DAC_CLK_SRC0 pin 100 istype 'com'; S/PDIF_MCLK_RATE pin 3 istype 'com'; // S2-7 S/PDIF_RESET_IN pin 4 istype 'com'; MODE11,MODE12,MODE13,MODE14 STAND_ALONE,MODE22,MODE23,MODE24 // S2-8 pin 5,6,8,9 istype 'com'; // S4 pin 10,11,14,15 istype 'com'; // S5 "NODES I_DSDATA1, I_DSDATA2, I_DSDATA3, I_DSDATA4 node istype 'com'; I_DBCLK, I_DLRCLK node istype 'com'; I_ASDATA1, I_ASDATA2 node istype 'com, buffer'; I_ABCLK, I_ALRCLK node istype 'com'; Qdivide // S2-5 // S2-6 node istype 'reg, buffer'; Rev. 0 | Page 21 of 32 UG-046 Evaluation Board User Guide //================================================================================ "MACROS // Switch S3, DIP POSITIONS 6 AND 7 ADC_HDR_NORMAL = ( MODE22 & MODE23); ADC_HDR_DATA2_DATA1 = ( MODE22 & !MODE23); ADC_HDR_TDM = (!MODE22 & MODE23); ADC_HDR_AUX = (!MODE22 & !MODE23); S/PDIF_OUT_MUX = MODE24; // HEX Switch S4 // S4 position 0, DAC_RX_ALL = ( MODE14 & MODE13 & MODE12 & MODE11); // S4 position 1, DAC_RX_1 = ( MODE14 & MODE13 & MODE12 & !MODE11); // S4 position 2, DAC_RX_2 = ( MODE14 & MODE13 & DAC_RX_3 = ( MODE14 & MODE13 & !MODE12 & MODE11); // S4 position 3, !MODE12 & !MODE11); // S4 position 4, DAC_RX_4 = ( MODE14 & !MODE13 & MODE12 & MODE11); // S4 position 5, NA1 = ( MODE14 & !MODE13 & NA2 = ( MODE14 & !MODE13 & MODE12 & !MODE11); // S4 position 6, !MODE12 & MODE11); // S4 position 7, DAC_DATA_ZERO = ( MODE14 & !MODE13 & !MODE12 & !MODE11); // S4 position 8, DAC_HDR1_ALL = ( !MODE14 & MODE13 & DAC_HDR1_IND = ( !MODE14 & MODE13 & MODE12 & MODE11); // S4 position 9, MODE12 & !MODE11); // S4 position A, DAC_HDR1_TDM = ( !MODE14 & MODE13 & !MODE12 & MODE11); Rev. 0 | Page 22 of 32 Evaluation Board User Guide UG-046 // S4 position B, DAC_DUAL_TDM = ( !MODE14 & MODE13 & DAC_HDR1_AUX = ( !MODE14 & !MODE13 & !MODE12 & !MODE11); // S4 position C, MODE12 & MODE11); // S4 position D, NA3 = ( !MODE14 & !MODE13 & MODE12 & !MODE11); // S4 position E, NA4 = ( !MODE14 & !MODE13 & !MODE12 & MODE11); // S4 position F, DAC_DATA_HIZ = ( !MODE14 & !MODE13 & !MODE12 & !MODE11); // Switch S2 DAC_S/PDIF = (DAC_CLK_SRC1 & DAC_CLK_SRC0); DAC_HDR1 = (DAC_CLK_SRC1 & !DAC_CLK_SRC0); DAC_ADC = (!DAC_CLK_SRC1 & DAC_CLK_SRC0); DAC_DAC = (!DAC_CLK_SRC1 & !DAC_CLK_SRC0); ADC_S/PDIF = (ADC_CLK_SRC1 & ADC_CLK_SRC0); ADC_HDR1 = (ADC_CLK_SRC1 & !ADC_CLK_SRC0); ADC_ADC = (!ADC_CLK_SRC1 & ADC_CLK_SRC0); ADC_DAC = (!ADC_CLK_SRC1 & !ADC_CLK_SRC0); "==================================================================================== EQUATIONS S/PDIF_RESET_OUT = S/PDIF_RESET_IN; // Configuration of the CS8416, changes active on reset, BCLK_8416 and LRCLK_8416 are bidirectional signals. SOMS_RX = DAC_S/PDIF; // SOMS = Serial Output Master/Slave Select SFSEL1_RX = 0; //DIR_RJ # DIR_RJ16; // SFSEL1 = Serial Format Select 1 SFSEL0_RX = 1; //DIR_I2S # DIR_DSP; // SFSEL0 = Serial Format Select 0 RMCKF_RX = !S/PDIF_MCLK_RATE; // RMCKF = Receive Master Clock Frequency // M0_8414 = (0 # !DAC_S/PDIF); // M1_8414 = 1; // M2_8414 = 0; Rev. 0 | Page 23 of 32 UG-046 // Evaluation Board User Guide M3_8414 = 0; // CS8404 Tx interface mode select APMS_TX = 0; // Tx serial port is always slave in this application SFMT1_TX = 0; // Tx data format is I2S always SFMT0_TX = 1; // M0_8404 = 0; // M1_8404 = 0; // M2_8404 = 1; // I2S format only // divide 256Fs clock by 2 for 128Fs clock to the the S/PDIF Tx // Qdivide.clk = CPLD_MCLK; // Qdivide.d = !Qdivide; // MCLK_8406 = Qdivide; MCLK_8406 = CPLD_MCLK; BCLK_8406 = I_ABCLK; LRCLK_8406 = I_ALRCLK; SDATA_8406 = (ASDATA1 & S/PDIF_OUT_MUX) # (ASDATA2 & !S/PDIF_OUT_MUX); // For SPI mode, let external port drive the SPI port DBCLK.oe = (DAC_S/PDIF # DAC_HDR1 # DAC_ADC # !DAC_DAC) & (DAC_CLK_OFF); DLRCLK.oe = (DAC_S/PDIF # DAC_HDR1 # DAC_ADC # !DAC_DAC) & (DAC_CLK_OFF); ABCLK.oe = (ADC_S/PDIF # ADC_HDR1 # !ADC_ADC # ADC_DAC) & (ADC_CLK_OFF); ALRCLK.oe = (ADC_S/PDIF # ADC_HDR1 # !ADC_ADC # ADC_DAC) & (ADC_CLK_OFF); HDR1_DBCLK.oe = (DAC_S/PDIF # !DAC_HDR1 # DAC_ADC # DAC_DAC); HDR1_DLRCLK.oe = (DAC_S/PDIF # !DAC_HDR1 # DAC_ADC # DAC_DAC); HDR1_ABCLK.oe = (ADC_S/PDIF # !ADC_HDR1 # ADC_ADC # ADC_DAC); HDR1_ALRCLK.oe = (ADC_S/PDIF # !ADC_HDR1 # ADC_ADC # ADC_DAC); BCLK_8416.oe = (!DAC_S/PDIF); LRCLK_8416.oe = (!DAC_S/PDIF); BCLK_8416 = I_DBCLK; LRCLK_8416 = I_DLRCLK; DSDATA1.oe = (!DAC_DATA_HIZ); DSDATA2.oe = (!(DAC_HDR1_TDM # DAC_DUAL_TDM # DAC_DATA_HIZ)); TDM-daisy chain mode DSDATA3.oe //DSDATA2 is output in DAC = (!DAC_DATA_HIZ); DSDATA4.oe = (!(DAC_DUAL_TDM # ADC_HDR_AUX # DAC_HDR1_AUX # DAC_DATA_HIZ)); TDM-OUT IN DUAL LINE DAC TDM MODE ASDATA2.oe = (ADC_HDR_TDM); //ASDATA2 is input in ADC TDM mode HDR1_DSDATA2.oe = (DAC_HDR1_TDM # DAC_DUAL_TDM); Rev. 0 | Page 24 of 32 // SECOND Evaluation Board User Guide UG-046 HDR1_DSDATA4.oe = (DAC_DUAL_TDM # ADC_HDR_AUX # DAC_HDR1_AUX); HDR1_ASDATA2.oe = (!ADC_HDR_TDM); DBCLK = I_DBCLK; DLRCLK = I_DLRCLK; ABCLK = I_ABCLK; ALRCLK = I_ALRCLK; DSDATA1 = (HDR1_DSDATA1 & (DAC_HDR1_ALL # DAC_HDR1_IND # DAC_RX_2 # DAC_RX_3 # DAC_RX_4 # DAC_HDR1_TDM # DAC_DUAL_TDM # ADC_HDR_AUX)) # (SDATA_8416 & (DAC_RX_ALL # DAC_RX_1)) # (0 & DAC_DATA_ZERO); DSDATA2 = (HDR1_DSDATA1 & DAC_HDR1_ALL) # (HDR1_DSDATA2 & (DAC_HDR1_IND # ADC_HDR_AUX # DAC_HDR1_AUX # DAC_RX_1 # DAC_RX_3 # DAC_RX_4)) # (SDATA_8416 & (DAC_RX_ALL # DAC_RX_2)) # (0 & DAC_DATA_ZERO); DSDATA3 = (HDR1_DSDATA1 & (DAC_HDR1_ALL)) # (HDR1_DSDATA3 & (DAC_HDR1_IND # DAC_DUAL_TDM # ADC_HDR_AUX # DAC_HDR1_AUX # DAC_RX_1 # DAC_RX_2 # DAC_RX_4)) # (SDATA_8416 & (DAC_RX_ALL # DAC_RX_3)) # (0 & DAC_DATA_ZERO); DSDATA4 = (HDR1_DSDATA1 & (DAC_HDR1_ALL)) # (HDR1_DSDATA4 & (DAC_HDR1_IND # DAC_RX_1 # DAC_RX_2 # DAC_RX_3)) # (SDATA_8416 & (DAC_RX_ALL # DAC_RX_4)) # (0 & DAC_DATA_ZERO); HDR1_DBCLK = I_DBCLK; HDR1_DLRCLK = I_DLRCLK; HDR1_ABCLK = I_ABCLK; HDR1_ALRCLK = I_ALRCLK; HDR1_ASDATA1 = (ASDATA1 & (ADC_HDR_NORMAL # ADC_HDR_TDM # ADC_HDR_AUX # DAC_HDR1_AUX )) # (ASDATA2 & ADC_HDR_DATA2_DATA1); HDR1_ASDATA2 = ASDATA2; ASDATA2 = HDR1_ASDATA2; HDR1_DSDATA2 = DSDATA2; HDR1_DSDATA4 = DSDATA4; // Internal node signals I_DBCLK = (BCLK_8416 & DAC_S/PDIF) # (HDR1_DBCLK & DAC_HDR1) # (DBCLK & DAC_DAC) # (I_ABCLK & DAC_ADC); I_DLRCLK = (LRCLK_8416 & DAC_S/PDIF) # (HDR1_DLRCLK & DAC_HDR1) # (DLRCLK & DAC_DAC) # (I_ALRCLK & DAC_ADC); I_ABCLK = (BCLK_8416 & ADC_S/PDIF) # (HDR1_ABCLK & ADC_HDR1) # (ABCLK & ADC_ADC) # (I_DBCLK & ADC_DAC); I_ALRCLK = (LRCLK_8416 & ADC_S/PDIF) # (HDR1_ALRCLK & ADC_HDR1) # (ALRCLK & ADC_ADC) # (I_DLRCLK & ADC_DAC); "==================================================================================== END IF_Logic Rev. 0 | Page 25 of 32 UG-046 Evaluation Board User Guide ORDERING INFORMATION BILL OF MATERIALS Table 1. Qty 18 46 9 12 8 16 1 32 3 12 Designator C85, C90 to C94, C101 to C103, C107, C108, C110, C115, C116, C121, C127, C132, C134 C2, C5, C8 to C10, C20, C21, C28, C29, C38, C42, C48 to C51, C58 to C60, C62, C64, C69, C73, C76, C79, C82, C99, C112, C118, C128, C135, C146, C147, C149, C151, C155, C156, C158, C162, C168, C174, C176, C177, C193, C194, C197, C203 C37, C65, C67, C83, C88, C124, C129, C157, C160 R28, R30, R51, R59, R166, R167, R169, R172, R185, R189, R212, R214 C68, C71, C87, C89, C130, C138, C159, C161 R24, R31, R44, R60, R77, R84, R93, R106, R136, R149, R159, R170, R180, R191, R207, R217 C84 R6, R7, R13, R14, R18, R20, R40, R43, R47 to R49, R54, R55, R63, R64, R74, R78, R80, R82, R102, R117, R158, R164, R173, R176, R177, R184, R186, R224 to R227 C6, C39, C40 2 C15 to C17, C81, C86, C95, C98, C170, C175, C178, C180, C183 C104, C106, C109, C111, C117, C123, C140 to C145 C4, C74 4 C61, C77, C113, C150 3 9 1 D1, D3, D4 C23, C33, C43, C55, C114, C166, C184, C188, C200 C36 2 C153, C154 8 R76, R81, R90, R101, R134, R141, R157, R168 R4 12 2 10 R91, R94, R98, R99, R108, R109, R114, R115, R118, R123 Description Multilayer ceramic capacitor, 16 V, X7R (0402) Manufacturer Panasonic EC Part Number ECJ-0EX1C104K Multilayer ceramic capacitor, 50 V, X7R (0603) Panasonic EC ECJ-1VB1H104K Multilayer ceramic capacitor, 50 V, NP0 (0603) Chip resistor, 100 kΩ, 1%, 125 mW, thick film (0603) Panasonic EC ECJ-1VC1H102J Panasonic EC ERJ-3EKF1003V Panasonic EC ECJ-1VC1H101J Panasonic EC ERJ-3EKF1000V Panasonic EC EEE-FC1C101P Panasonic EC ERJ-3EKF1002V TDK Corp C1608C0G1E103J Panasonic EC ECJ-1VC2A100D Kemet C0402C100J5GACTU Panasonic EC EEE-FC1C100R Panasonic EC ECJ-1VC1H121J ON Semiconductor Murata Electronics 1SMB15AT3G GRM1885C1H222JA01D Murata ENA GRM21B5C1H223JA01L Panasonic EC ECJ-1VC1H220J Panasonic EC ERJ-3EKF2370V Panasonic EC ERJ-3EKF2430V Rohm MCR01MZPF24R9 Multilayer ceramic capacitor, 50 V, NP0 (0603) Chip resistor, 100 kΩ, 1%, 100 mW, thick film (0603) Aluminum electrolytic capacitor, 100 μF, 16 V, FC, 105 deg, SMD_E Chip resistor, 10 kΩ, 1%, 125 mW, thick film (0603) Multilayer ceramic capacitor, 25 V, NP0 (0603) Multilayer ceramic capacitor, 100 V, NP0 (0603) Multilayer ceramic capacitor, 50 V, NP0 (0402) Aluminum electrolytic capacitor, 16 V, FC, 105 deg, SMD_B Multilayer ceramic capacitor, 50 V, NP0 (0603) TVS Zener, 15 V, 600 W, SMB Multilayer ceramic capacitor, 50 V, NP0 (0603 ) Multilayer ceramic capacitor, 25 V, NP0 (0805) Multilayer ceramic capacitor, 50 V, NP0 (0603) Chip resistor, 237 Ω, 1%, 125 mW, thick film (0603) Chip resistor, 243 Ω, 1%, 100 mW, thick film (0603) Chip resistor, 24.9 Ω, 1%, 63 mW, thick film (0402) Rev. 0 | Page 26 of 32 Evaluation Board User Guide Qty 16 3 Designator R56, R57, R65, R66, R88, R89, R140, R154, R179, R183, R213, R216, R228 to R231 C25, C31, C45, C53, C169, C181, C190, C198 R3, R11, R58 1 C125 4 R5, R52, R53, R75 1 C120 33 R38 1 R129 8 3 C24, C34, C44, C56, C167, C185, C189, C201 C11, C14, C22, C26, C27, C30, C32, C35, C41, C46, C47, C52, C54, C57, C63, C66, C72, C75, C80, C105, C119, C133, C139, C148, C152, C164, C172, C179, C191, C196 C12, C18, C19 4 R83, R96, R148, R163 20 1 R103, R104, R110 to R112, R116, R119, R124, R126 to R128, R130 to R132, R142 to R147 R8 to R10, R15 to R17, R19, R92, R95, R100, R105, R113, R120, R125, R133, R135, R139, R153, R155, R156, R160, R174, R175, R178, R187, R188, R190, R194, R196, R200, R201, R203, R206, R210, R215 R25, R26, R32, R34, R45, R46, R61, R68, R181, R182, R192, R195, R208, R209, R218, R220 R21 to R23, R27, R33, R35 to R37, R39, R41, R42, R50, R62, R69 to R71 C131 1 R138 16 4 R72, R73, R79, R85 to R87, R97, R107, R121, R122, R137, R150 to R152, R165, R171 C78, C137, C171, C195 1 2 1 U11 U19, U26 R29 1 R67 8 30 35 16 16 UG-046 Description Chip resistor, 24.9 Ω, 1%, 100 mW, thick film (0603) Manufacturer Rohm Part Number MCR03EZPFX24R9 Multilayer ceramic capacitor, 50 V, NP0 (0603) Chip resistor, 374 Ω, 1%, 100 mW, thick film (0603) Multilayer ceramic capacitor, 50 V, NP0 (0603) Chip resistor, 392 Ω, 1%, 100 mW, thick film (0603) Multilayer ceramic capacitor, 16 V, ECH-U (1206) Chip resistor, 3.01 kΩ, 1%, 100 mW, thick film (0603) Chip resistor, 3.32 kΩ, 1%, 100 mW, thick film (0603) Multilayer ceramic capacitor, 50 V, NP0 (0603) Aluminum electrolytic capacitor, 16 V, FC, 105 deg, SMD_D Rohm MCH185A271JK Rohm MCR03EZPFX3740 Panasonic EC ECJ-1VC1H391J Rohm MCR03EZPFX3920 Panasonic EC ECH-U1C393JB5 Rohm MCR03EZPFX3011 Rohm MCR03EZPFX3321 Murata ENA GRM1885C1H431JA01D Panasonic EC EEE-FC1C470P Panasonic EC EEE-FC1E470P Panasonic EC ERJ-3EKF4992V Rohm MCR01MZPF49R9 Chip resistor, 49.9 kΩ, 1%, 100 mW, thick film (0603) Panasonic EC ERJ-3EKF49R9V Chip resistor, 49.9 kΩ, 1%, 100 mW, thick film (0603) Panasonic EC ERJ-3EKF4641V Chip resistor, 49.9 kΩ, 1%, 100 mW, thick film (0603) Panasonic EC ERJ-3EKF4751V Multilayer ceramic capacitor, 25 V, NP0 (0603) Chip resistor, 562 Ω, 1%, 125 mW, thick film (0603) Chip resistor, 5.76 kΩ, 1%, 125 mW, thick film (0603) TDK Corp C1608C0G1E562J Panasonic EC ERJ-3EKF5620V Panasonic EC ERJ-3EKF5761V Panasonic EC ECJ-1VC2A680J NXP Semi Texas Instruments Panasonic EC 74HC04D-T SN74LV125AD ERJ-3EKF75R0V Rohm MCR03EZPFX90R9 Aluminum electrolytic capacitor, FC, 105 deg, SMD_E Chip resistor, 49.9 kΩ, 1%, 100 mW, thick film (0603) Chip resistor, 49.9 kΩ, 1%, 63 mW, thick film (0402) Multilayer ceramic capacitor, 100 V, NP0 (0603) IC inverter, hex, TTL/LSTTL, 14 SOIC IC buffer, quad, three state, 14 SOIC Chip resistor, 75 Ω, 1%, 100 mW, thick film (0603) Chip resistor, 90.9 Ω, 1% 100 mW, thick film (0603) Rev. 0 | Page 27 of 32 UG-046 Evaluation Board User Guide Qty 1 Designator Y1 Description Crystal, 12.288 MHz, SMT, 10 pF Manufacturer Abracon Corp 1 U15 Analog Devices 1 1 1 U23 U1 J2 1 J3 1 J4 2 1 J22, J23 U8 1 U13 2 1 1 6 1 2 4 1 D2, D5 S1 SW1 L2 to L7 L1 J1, J14 J15 to J18 J19 Four ADC/eight DAC with PLL, 192 kHz, 24bit CODEC Microprocessor voltage supervisor Voltage regulator, low dropout 5-way binding post, black, uninsulated base TH 5-way binding post, mini, green, uninsulated base TH 5-way binding post, mini, red, uninsulated base TH SMA receptacle, straight PCB mount 192 kHz digital audio receiver (DGTL RCVR 28-TSSOP) 192 kHz digital audio interface (S/PDIF transmitter) Passivated rectifier, 1 A, 50 V, MELF Switch slide, DP3T, PC MNT, L = 4 mm DPDT slide switch, vertical Chip ferrite bead, 600 Ω at 100 MHz Chip ferrite bead, 600 Ω at 100 MHz 10-way shrouded polarized header 16-way unshrouded, not populated Connector header, 0.100 dual STR, 72 POS 2 J20, J26 Connector header, 0.100 dual STR, 72 POS Sullins 4 J5 to J8 Connector header, 0.100 dual STR, 72 POS Sullins 2 19 16-position rotary switch, hex 2-pin header, unshrouded jumper, 0.10"; use shunt Tyco 881545-2 APEM Sullins 3-position SIP header Sullins 1 S4, S5 JP4 to JP7, JP11 to JP14, JP17, JP18, JP20 to JP22, JP24, JP26, JP28 to JP31 JP1 to JP3, JP8 to JP10, JP15, JP19, JP23, JP25, JP27 U16 1 D11 Lattice Semiconductor Lumex Opto SML-LX1206GW-TR 2 D6, D9 Lumex Opto SML-LX1206IW-TR 2 D7, D10 U2, U3 CML Innovative Tech STMicroelectronics CMD15-21VYD/TR8 2 6 2 8 CUI CTS Analog Devices SJ-3523-SMT 773091103 OP275GSZ 1 J10, J11, J13, J21, J27, J28 R161, R162 U6, U9, U12, U14, U17, U20, U24, U25 U21 Complex programmable logic devices (CPLD), HI PERF, E2CMOS, PLD Green, diffused, 10 millicandela, 565 nm (1206) Red, diffused, 6.0 millicandela, 635 nm (1206) Yellow, diffused, 4.0 millicandela, 585 nm (1206) 3-terminal, adjustable voltage regulator, DPak Sterero mini jack, SMT Resistor network, bussed 9 res Dual bipolar/JFET audio op amp. Abracon Corp AP3S-12.288MHz-F-J-B 2 J9, J12 Connect-Tech Products CTP-021A-S-YEL 11 12.288 MHz fixed SMD oscillator, 1.8 V dc to 3.3 V dc RCA jack, PCB, TH mount, R/A, yellow Rev. 0 | Page 28 of 32 Part Number ABM3B-12.288MHZ-101-U-T AD1974YSTZ Analog Devices Analog Devices Deltron Components Deltron Components Deltron Components Amp-RF Division Cirrus Logic ADM811RARTZ-REEL7 ADP3303ARZ-3.3 552-0100 BLK Cirrus Logic CS8406-CZZ Micro Commercial E-Switch E-Switch TDK Steward 3M 3M Sullins DL4001-TP EG2305 EG2207 MPZ1608S601A HZ0805E601R-10 N2510-6002RB N/A PBC10DAAN; or cut PBC36DAAN PBC13DAAN; or cut PBC36DAAN PBC06DAAN; or cut PBC36DAAN PT65503 PBC02SAAN; or cut PBC36SAAN 552-0400 GRN 552-0500 RED 901-144-8RFX CS8416-CZZ PBC03SAAN; or cut PBC36SAAN LC4128V-75TN100C LM317MDT-TR Evaluation Board User Guide UG-046 Qty 1 Designator U10 Description 110 Ω AES/EBU transformer 2 1 2 2 1 1 U18, U22 U4 SW2, SW3 S2, S3 S6 U5 1 60 U7 TP1 to TP6, TP8 to TP10, TP12 to TP15, TP17, TP19 to TP23, TP25 to TP52, TP54 to TP60, TP62, TP64 to TP68 Buffer, three-state, single gate Octal, three-state buffer/driver SPDT slide switch PC mount 8-position SPST SMD switch, flush, actuated Tact switch, 6 mm gull wing 15 Mb/sec fiber optic receiving module with shutter Fiber optic transmit module, 15 Mb/sec Mini test point, white, 0.1 inch, OD Rev. 0 | Page 29 of 32 Manufacturer Scientific Conversion Texas Instruments Texas Instruments E-Switch CTS Corp Tyco/Alcoswitch Toshiba Toshiba Keystone Electronics Part Number SC937-02 SN74LVC1G125DRLR SN74LVC541ADBR EG1218 219-8LPST FSM6JSMA TORX147L(F,T) TOTX147L(F,T) 5002 UG-046 Evaluation Board User Guide NOTES Rev. 0 | Page 30 of 32 Evaluation Board User Guide UG-046 NOTES Rev. 0 | Page 31 of 32 UG-046 Evaluation Board User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08424-0-2/10(0) Rev. 0 | Page 32 of 32