PDF Data Sheet Rev. A

16-Channel, High Performance,
192 kHz, 24-Bit DAC
ADAU1966A
Data Sheet
FEATURES
GENERAL DESCRIPTION
Differential or single-ended voltage DAC output
114 dB DAC dynamic range, A-weighted, differential
−97 dB total harmonic distortion plus noise (THD + N),
differential
110 dB DAC dynamic range, A-weighted, single-ended
−95 dB THD + N, single-ended
2.5 V digital and 3.3 V analog and input/output (I/O) supplies
299 mW total quiescent power
Phase-locked loop (PLL) generated or direct master clock
Low electromagnetic interference (EMI) design
Linear regulator driver to generate digital supply
Supports 24-bit and 32 kHz to 192 kHz sample rates
Low propagation 192 kHz sample rate mode
Log volume control with autoramp function
Temperature sensor with digital readout ±3°C accuracy
SPI and I2C controllable for flexibility
Software-controllable clickless mute
Software power-down
Right justified, left justified, I2S, and TDM modes
Master and slave modes with up to 16-channel input/output
80-lead LQFP package
Qualified for automotive applications
The ADAU1966A is a high performance, single-chip digital-toanalog converter (DAC) that provides 16 DACs with differential or
single-ended outputs using the Analog Devices, Inc., patented
multibit sigma-delta (Σ-Δ) architecture. A serial peripheral interface
(SPI)/I2C port is included, allowing a microcontroller to adjust
volume and many other parameters. The ADAU1966A operates
from 2.5 V digital and 3.3 V analog supplies. A linear regulator
is included to generate the digital supply voltage from the analog
supply voltage. The ADAU1966A is available in an 80-lead LQFP.
The ADAU1966A is designed for low EMI. This consideration
is apparent in both the system and circuit design architectures.
By using the on-board PLL to derive the internal master clock from
an external left-right frame clock (LRCLK), the ADAU1966A
can eliminate the need for a separate high frequency master clock
and can be used with or without a bit clock. The DACs are
designed using the latest Analog Devices continuous time
architectures to further minimize EMI. By using 2.5 V digital
supplies, power consumption is minimized, and the digital
waveforms are a smaller amplitude, further reducing emissions.
Note that throughout this data sheet, multifunction pins, such as
SCLK/SCL, are referred to by the entire pin name or by a single
function of the pin, for example, SCLK, when only that function
is relevant.
APPLICATIONS
Automotive audio systems
Home theater systems
Digital audio effects processors
FUNCTIONAL BLOCK DIAGRAM
DIGITAL AUDIO
INPUT
ADAU1966A
SERIAL DATA PORT
DAC
DAC
DAC
DAC
DAC
DAC
DAC
DAC
SDATA
IN
CLOCKS
TIMING MANAGEMENT
AND CONTROL
(CLOCK AND PLL)
DAC
DAC
DIGITAL
FILTER
AND
VOLUME
CONTROL
DAC
DAC
ANALOG
AUDIO
OUTPUTS
DAC
DAC
DAC
DAC
PRECISION
VOLTAGE
REFERENCE
SPI/I2C
CONTROL PORT
CONTROL DATA
INPUT/OUTPUT
INTERNAL
TEMP
SENSOR
11298-001
ANALOG
AUDIO
OUTPUTS
DIGITAL
FILTER
AND
VOLUME
CONTROL
SDATA
IN
Figure 1.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2013–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADAU1966A
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 Block Power-Down and Thermal Sensor Control 1 Register
....................................................................................................... 27 General Description ......................................................................... 1 Power-Down Control 2 Register .............................................. 28 Functional Block Diagram .............................................................. 1 Power-Down Control 3 Register .............................................. 29 Revision History ............................................................................... 2 Thermal Sensor Temperature Readout Register .................... 30 Specifications..................................................................................... 3 DAC Control 0 Register ............................................................ 30 Analog Performance Specifications: TA = 25°C ....................... 3 DAC Control 1 Register ............................................................ 31 Analog Performance Specifications: TA = 105°C ..................... 4 DAC Control 2 Register ............................................................ 32 Crystal Oscillator Specifications................................................. 4 DAC Individual Channel Mutes 1 Register ............................ 33 Digital Input/Output Specifications........................................... 5 DAC Individual Channel Mutes 2 Register ............................ 34 Power Supply Specifications........................................................ 5 Master Volume Control Register.............................................. 35 Digital Filters ................................................................................. 6 DAC 1 Volume Control Register .............................................. 35 Timing Specifications .................................................................. 6 DAC 2 Volume Control Register .............................................. 36 Absolute Maximum Ratings............................................................ 8 DAC 3 Volume Control Register .............................................. 36 Thermal Resistance ...................................................................... 8 DAC 4 Volume Control Register .............................................. 37 ESD Caution .................................................................................. 8 DAC 5 Volume Control Register .............................................. 37 Pin Configuration and Function Descriptions ............................. 9 DAC 6 Volume Control Register .............................................. 38 Typical Performance Characteristics ........................................... 12 DAC 7 Volume Control Register .............................................. 38 Typical Application Circuits.......................................................... 13 DAC 8 Volume Control Register .............................................. 39 Theory of Operation ...................................................................... 14 DAC 9 Volume Control Register .............................................. 39 DACs ............................................................................................ 14 DAC 10 Volume Control Register............................................ 40 Clock Signals ............................................................................... 14 DAC 11 Volume Control Register............................................ 40 Power-Up and Reset ................................................................... 16 DAC 12 Volume Control Register............................................ 41 Standalone Mode ........................................................................ 16 DAC 13 Volume Control Register............................................ 41 I2C Control Port .......................................................................... 16 DAC 14 Volume Control Register............................................ 42 Serial Control Port: SPI Control Mode ................................... 19 DAC 15 Volume Control Register............................................ 42 Power Supply and Voltage Reference ....................................... 20 DAC 16 Volume Control Register............................................ 43 Serial Data Ports—Data Format ............................................... 20 Pad Strength Register ................................................................. 43 Time-Division Multiplexed (TDM) Modes ............................ 21 DAC Power Adjust 1 Register ................................................... 44 Temperature Sensor ................................................................... 21 DAC Power Adjust 2 Register ................................................... 45 Additional Modes ....................................................................... 23 DAC Power Adjust 3 Register ..................................................... 46 Register Summary .......................................................................... 24 DAC Power Adjust 4 Register ................................................... 47 Register Details ............................................................................... 25 Outline Dimensions ....................................................................... 51 PLL and Clock Control 0 Register ........................................... 25 Ordering Guide .......................................................................... 51 PLL and Clock Control 1 Register ........................................... 26 Automotive Products ................................................................. 51 REVISION HISTORY
3/16—Rev. 0 to Rev. A
Changes to Table 4 ............................................................................ 5
8/13—Revision 0: Initial Version
Rev. A | Page 2 of 52
Data Sheet
ADAU1966A
SPECIFICATIONS
Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications.
Master clock = 12.288 MHz (48 kHz fS, 256 × fS mode), input sample rate = 48 kHz, measurement bandwidth = 20 Hz to 20 kHz, word width =
24 bits, load capacitance (digital output) = 20 pF, load current (digital output) = ±1 mA or 1.5 kΩ to ½ DVDD supply, input voltage high = 2.0 V,
input voltage low = 0.8 V, analog audio output resistive load = 3100 Ω per pin, unless otherwise noted.
ANALOG PERFORMANCE SPECIFICATIONS: TA = 25°C
Specifications guaranteed at supply voltages of AVDDx = 3.3 V, DVDD = 2.5 V, ambient temperature1 (TA) = 25°C, unless otherwise
noted.
Table 1.
Parameter
DIGITAL-TO-ANALOG CONVERTERS
Dynamic Range (DNR)
No Filter (RMS)
With A-Weighted Filter (RMS)
No Filter (RMS)
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise
Differential Output
Single-Ended Output
Full-Scale Differential Output Voltage
Full-Scale Single-Ended Output Voltage
Gain Error
Offset Error
Gain Drift
Interchannel Isolation
Interchannel Phase Deviation
Volume Control Step
Volume Control Range
De-Emphasis Gain Error
Output Resistance at Each Pin
REFERENCE
Temperature Sensor Reference Voltage
Common-Mode Reference Output
External Reference Voltage Source
REGULATOR
Input Supply Voltage
Regulated Output Voltage
TEMPERATURE SENSOR
Temperature Accuracy
Temperature Readout Range
Temperature Readout Step Size
Temperature Sample Rate
1
Test Conditions/Comments
Min
Typ
20 Hz to 20 kHz, −60 dB input
Differential output
Differential output
Single-ended output
Single-ended output
105.5
108.5
102.5
105.5
111
114
107
110
Two channels running −1 dBFS
All channels running −1 dBFS
Two channels running −1 dBFS
All channels running −1 dBFS
−97
−97
−95
−95
2.00 (2.83)
1.00 (1.41)
−10
−25
−30
−6
Max
Unit
dB
dB
dB
dB
−85
−85
−80
−80
+10
+25
+30
100
0
0.375
95.25
±0.6
33
dB
dB
dB
dB
V rms (V p-p)
V rms (V p-p)
%
mV
ppm/°C
dB
Degrees
dB
dB
dB
Ω
TS_REF pin
CM pin
CM pin
1.40
1.40
1.50
1.50
1.50
1.56
1.56
V
V
V
VSUPPLY pin
VSENSE pin
3.14
2.25
3.3
2.50
3.46
2.59
V
V
+3
+140
°C
°C
°C
Hz
−3
−60
1
0.25
Functionally guaranteed at −40°C to +125°C, case temperature.
Rev. A | Page 3 of 52
6
ADAU1966A
Data Sheet
ANALOG PERFORMANCE SPECIFICATIONS: TA = 105°C
Specifications guaranteed at supply voltages of AVDDx = 3.3 V, DVDD = 2.5 V, ambient temperature1 (TA) = 105°C, unless otherwise
noted.
Table 2.
Parameter
DIGITAL-TO-ANALOG CONVERTERS
Dynamic Range (DNR)
No Filter (RMS)
With A-Weighted Filter (RMS)
No Filter (RMS)
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise
Differential Output
Single-Ended Output
Full-Scale Differential Output Voltage
Full-Scale Single-Ended Output Voltage
Gain Error
Offset Error
Gain Drift
Interchannel Isolation
Interchannel Phase Deviation
Volume Control Step
Volume Control Range
De-Emphasis Gain Error
Output Resistance at Each Pin
REFERENCE
Temperature Sensor Reference Voltage
Common-Mode Reference Output
External Reference Voltage Source
REGULATOR
Input Supply Voltage
Regulated Output Voltage
TEMPERATURE SENSOR
Temperature Accuracy
Temperature Readout Range
Temperature Readout Step Size
Temperature Sample Rate
1
Test Conditions/Comments
Min
Typ
20 Hz to 20 kHz, −60 dB input
Differential output
Differential output
Single-ended output
Single-ended output
106.5
109.5
101.5
104.5
110
113
108
110
Two channels running −1 dBFS
All channels running −1 dBFS
Two channels running −1 dBFS
All channels running −1 dBFS
−92
−92
−90
−90
2.00 (2.83)
1.00 (1.41)
−10
−25
−30
−6
Max
Unit
dB
dB
dB
dB
−83
−83
−80
−80
+10
+25
+30
100
0
0.375
95.25
±0.6
33
dB
dB
dB
dB
V rms (V p-p)
V rms (V p-p)
%
mV
ppm/°C
dB
Degrees
dB
dB
dB
Ω
TS_REF pin
CM pin
CM pin
1.40
1.40
1.50
1.50
1.50
1.56
1.56
V
V
V
VSUPPLY pin
VSENSE pin
3.14
2.25
3.3
2.50
3.46
2.55
V
V
+3
+140
°C
°C
°C
Hz
−3
−60
1
0.25
6
Functionally guaranteed at −40°C to +125°C, case temperature.
CRYSTAL OSCILLATOR SPECIFICATIONS
Table 3.
Parameter
TRANSCONDUCTANCE
TA = 25°C
TA = 105°C
Min
Typ
Max
Unit
6.4
5.2
7 to 10
7.5 to 8.5
14
12
mmhos
mmhos
Rev. A | Page 4 of 52
Data Sheet
ADAU1966A
DIGITAL INPUT/OUTPUT SPECIFICATIONS
−40°C < TA < +105°C, IOVDD = 3.3 V ± 5%, unless otherwise noted.
Table 4.
Parameter
DIGITAL INPUT
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
Input Leakage
INPUT CAPACITANCE
DIGITAL OUTPUT
High Level Output Voltage (VOH)
Low Level Output Voltage (VOL)
Test Conditions/Comments
Min
Typ
Max
Unit
0.3 × IOVDD
10
10
5
V
V
μA
μA
pF
0.1 × IOVDD
V
V
0.7 × IOVDD
IIH at VIH = 3.3 V
IIL at VIL = 0 V
IOH = 1 mA
IOL = 1 mA
0.8 × IOVDD
POWER SUPPLY SPECIFICATIONS
Table 5.
Parameter
SUPPLIES
Voltage
Analog Current
Normal Operation
Power-Down
Digital Current
Normal Operation
Power-Down
PLL Current
Normal Operation
Power-Down
Input/Output Current
Normal Operation
Power-Down
QUIESCENT DISSIPATION—DITHER INPUT
Operation
All Supplies
Analog Supply
Digital Supply
PLL Supply
I/O Supply
Power-Down, All Supplies
POWER SUPPLY REJECTION RATIO
Signal at Analog Supply Pins
Test Conditions/Comments
Min
Typ
Max
Unit
AVDDx
DVDD
PLLVDD
IOVDD
VSUPPLY
AVDDx = 3.3 V
3.14
2.25
2.25
3.14
3.14
3.3
2.5
2.5
3.3
3.3
3.46
3.46
3.46
3.46
3.46
V
V
V
V
V
DVDD = 2.5 V
fS = 48 kHz to 192 kHz
No MCLK or I2S
PLLVDD = 2.5 V
fS = 48 kHz to 192 kHz
60
1
mA
μA
30
4
mA
μA
5
1
mA
μA
4
1
mA
μA
299
198
75
13
13
0
mW
mW
mW
mW
mW
mW
88
85
85
75
dB
dB
dB
dB
IOVDD = 3.3 V
MCLK = 256 × fS, 48 kHz
AVDDx = 3.3 V, DVDD/PLLVDD = 2.5 V, IOVDD = 3.3 V
AVDDx = 3.3 V, 12.4 mW per channel
DVDD = 2.5 V
PLLVDD = 2.5 V
IOVDD = 3.3 V
1 kHz, 200 mV p-p, differential
20 kHz, 200 mV p-p, differential
1 kHz, 200 mV p-p, single-ended
20 kHz, 200 mV p-p, single-ended
Rev. A | Page 5 of 52
ADAU1966A
Data Sheet
DIGITAL FILTERS
Table 6.
Parameter
DAC INTERPOLATION FILTER
Pass Band
Pass-Band Ripple
Transition Band
Stop Band
Stop-Band Attenuation
Propagation Delay
Mode
Factor
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
48 kHz mode, typical at 48 kHz
96 kHz mode, typical at 96 kHz
192 kHz mode, typical at 192 kHz
192 kHz low propagation delay mode, typical at 192 kHz
0.4535 × fS
0.3646 × fS
0.3646 × fS
Min
Typ
Max
22
35
70
±0.01
±0.05
±0.1
0.5 × fS
0.5 × fS
0.5 × fS
0.5465 × fS
0.6354 × fS
0.6354 × fS
24
48
96
26
61
122
68
68
68
25/fS
11/fS
8/fS
2/fS
521
115
42
10
Unit
kHz
kHz
kHz
dB
dB
dB
kHz
kHz
kHz
kHz
kHz
kHz
dB
dB
dB
μs
μs
μs
μs
TIMING SPECIFICATIONS
−40°C < TA < +105°C, DVDD = 2.5 V ± 10%, unless otherwise noted.
Table 7.
Parameter1
INPUT MASTER CLOCK (MCLKI) AND RESET
tMH
fMCLK
fBCLK
tPDR
tPDRR
PLL
Lock Time
Output Duty Cycle, MCLKO Pin
Description
Min
Master clock duty cycle, DAC clock source = PLL clock at
256 × fS, 384 × fS, 512 × fS, and 768 × fS
DAC clock source = direct MCLKI at 512 × fS (bypass onchip PLL)
MCLKI frequency of the MCLKI/XTALI pin, PLL mode
Direct MCLKI 512 × fS mode
DBCLK pin frequency, PLL mode
Low
Recovery, reset to active output
MCLKI input of the MCLKI/XTALI pin
DLRCLK pin input
256 × fS VCO clock
Rev. A | Page 6 of 52
Typ
Max
Unit
40
60
%
40
60
%
6.9
40.5
27.1
27.0
MHz
MHz
MHz
ns
ms
10
50
60
ms
ms
%
15
300
40
Data Sheet
ADAU1966A
Parameter1
SPI PORT
fSCLK
tSCH
tSCL
tMOS
tMOH
tSSS
tSSH
tSSHIGH
tMIE
tMID
tMIH
tMITS
Description
See Figure 19
SCLK frequency, not shown in Figure 19
SCLK high
SCLK low
MOSI setup, time to SCLK rising
MOSI hold, time from SCLK rising
SS setup, time to SCLK rising
SS hold, time from SCLK falling
SS high
MISO enable from SS falling
MISO delay from SCLK falling
MISO hold from SCLK falling, not shown in Figure 19
MISO tristate from SS rising
2
IC
fSCL
tSCLL
tSCLH
tSCS
See Figure 2 and Figure 15
SCL clock frequency
SCL low
SCL high
Setup time (start condition), relevant for repeated start
condition
Hold time (start condition), first clock generated after
this period
Setup time (stop condition)
Data setup time
SDA and SCL rise time
SDA and SCL fall time
Bus-free time between stop and start
See Figure 21
DBCLK high, slave mode
DBCLK low, slave mode
DLRCLK setup, time to DBCLK rising, slave mode
DLRCLK hold from DBCLK rising, slave mode
DLRCLK skew from DBCLK falling, master mode, not
shown in Figure 21
DSDATAx setup to DBCLK rising
DSDATAx hold from DBCLK rising
tSCH
tSSH
tDS
tSR
tSF
tBFT
DAC SERIAL PORT
tDBH
tDBL
tDLS
tDLH
tDLSK
tDDS
tDDH
tDS
SCL
tSCS
tSF
2
Figure 2. I C Timing Diagram
Rev. A | Page 7 of 52
tSSH
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
1.3
0.6
0.6
400
kHz
μs
μs
μs
0.6
μs
0.6
100
1.3
μs
ns
ns
ns
μs
10
10
10
5
−8
ns
ns
ns
ns
ns
300
300
10
5
tSCLH
tSCLL
10
30
tSCH
tBFT
Unit
30
SDA
tSR
Max
30
30
The timing specifications may refer to single functions of multifunction pins, such as the SCL function of the SCLK/SCL pin.
tSCH
Typ
35
35
10
10
10
10
10
11298-002
1
Min
+8
ns
ns
ADAU1966A
Data Sheet
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 8.
Parameter
Analog (AVDDx)
Input/Output (IOVDD)
Digital (DVDD)
PLL (PLLVDD)
VSUPPLY
Input Current (Except Supply Pins)
Analog Input Voltage (Signal Pins)
Digital Input Voltage (Signal Pins)
Operating Temperature Range (Case)
Storage Temperature Range
Rating
−0.3 V to +3.6 V
−0.3 V to +3.6 V
−0.3 V to +3.6 V
−0.3 V to +3.6 V
−0.3 V to +3.6 V
±20 mA
–0.3 V to AVDDx + 0.3 V
−0.3 V to DVDD + 0.3 V
−40°C to +125°C
−65°C to +150°C
θJA represents junction-to-ambient thermal resistance, and
θJC represents the junction-to-case thermal resistance. All
characteristics are for a 4-layer board with a solid ground plane.
Table 9. Thermal Resistance
Package Type
80-Lead LQFP
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. A | Page 8 of 52
θJA
42.3
θJC
10.0
Unit
°C/W
Data Sheet
ADAU1966A
DAC9P
DAC8N
DAC8P
DAC7N
73
72
71
70
69
DAC_BIAS3 1
AGND2
DAC9N
74
CM
DAC10P
75
TS_REF
DAC10N
76
DAC5P
DAC11P
77
DAC5N
DAC11N
78
DAC6P
DAC12P
79
DAC7P
DAC12N
80
DAC6N
AGND3
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
68
67
66
65
64
63
62
61
60
DAC_BIAS2
59
DAC_BIAS1
AVDD3 3
58
AVDD2
DAC13P 4
57
DAC4N
DAC13N 5
56
DAC4P
DAC14P 6
55
DAC3N
DAC14N 7
54
DAC3P
DAC15P 8
53
DAC2N
52
DAC2P
51
DAC1N
DAC16N 11
50
DAC1P
AVDD4 12
49
AVDD1
AGND4 13
48
AGND1
PLLGND 14
47
PU/RST
LF 15
46
SA_MODE
PLLVDD 16
45
SS/ADDR0/SA*
MCLKI/XTALI 17
44
SCLK/SCL
XTALO 18
43
MISO/SDA/SA*
MCLKO 19
42
MOSI/ADDR1/SA*
DVDD 20
41
DVDD
PIN 1
INDICATOR
DAC_BIAS4 2
ADAU1966A
DAC15N 9
34
35
36
37
38
39
40
11298-003
DBCLK
33
DGND
DGND
32
IOVDD
VSUPPLY
31
DSDATA1
VDRIVE
30
DSDATA2
VSENSE
29
DSDATA3
DGND
28
DSDATA4
27
DSDATA5
26
DSDATA6
25
SA2
24
SA1
23
DGND
22
DLRCLK
21
IOVDD
DAC16P 10
DVDD
TOP VIEW
(Not to Scale)
*SEE TABLE 13 FOR SA_MODE SETTINGS.
Figure 3. Pin Configuration
Table 10. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Mnemonic1, 2
DAC_BIAS3
DAC_BIAS4
AVDD3
DAC13P
DAC13N
DAC14P
DAC14N
DAC15P
DAC15N
DAC16P
DAC16N
AVDD4
AGND4
PLLGND
LF
PLLVDD
MCLKI/XTALI
XTALO
MCLKO
Type3
I
I
PWR
O
O
O
O
O
O
O
O
PWR
GND
GND
O
PWR
I
O
O
Description
DAC Bias 3. AC couple with a 470 nF to AGND3.
DAC Bias 4. AC couple with a 470 nF to AVDD3.
Analog Power.
DAC13 Positive Output.
DAC13 Negative Output.
DAC14 Positive Output.
DAC14 Negative Output.
DAC15 Positive Output.
DAC15 Negative Output.
DAC16 Positive Output.
DAC16 Negative Output.
Analog Power.
Analog Ground.
PLL Ground.
PLL Loop Filter. Reference the LF pin to PLLVDD.
PLL Power. Apply 2.5 V to power the PLL.
Master Clock Input/Input to Crystal Inverter. This is a multifunction pin.
Output from Crystal Inverter.
Master Clock Output.
Rev. A | Page 9 of 52
ADAU1966A
Data Sheet
Pin No.
20, 29, 41
21, 26, 30, 40
22, 39
23
Mnemonic1, 2
DVDD
DGND
IOVDD
VSENSE
Type3
PWR
GND
PWR
I
24
25
VDRIVE
VSUPPLY
O
I
27
28
31
DBCLK
DLRCLK
SA1
I/O
I/O
I
32
SA2
I
33
34
35
36
37
38
42
DSDATA6
DSDATA5
DSDATA4
DSDATA3
DSDATA2
DSDATA1
MOSI/ADDR1/SA
I
I
I
I
I
I
I
43
MISO/SDA/SA
I/O
44
45
SCLK/SCL
SS/ADDR0/SA
I
I
46
SA_MODE
I
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
PU/RST
AGND1
AVDD1
DAC1P
DAC1N
DAC2P
DAC2N
DAC3P
DAC3N
DAC4P
DAC4N
AVDD2
DAC_BIAS1
DAC_BIAS2
AGND2
CM
I
GND
PWR
O
O
O
O
O
O
O
O
PWR
I
I
GND
O
63
TS_REF
O
64
65
66
67
68
DAC5P
DAC5N
DAC6P
DAC6N
DAC7P
O
O
O
O
O
Description
Digital Power, 2.5 V.
Digital Ground.
Power for Digital Input and Output Pins, 3.3 V.
2.5 V Regulator Output, Pass Transistor Collector. Bypass VSENSE with a 10 μF capacitor in parallel
with a 100 nF capacitor.
Pass Transistor Base Driver.
3.3 V Voltage Regulator Input , Pass Transistor Emitter . Bypass VSUPPLY with a 10 μF capacitor in
parallel with a 100 nF capacitor.
Bit Clock for DACs.
Frame Clock for DACs.
Standalone Mode, Time Domain Multiplexed (SA_MODE TDM) State. See the Standalone Mode
section, Table 13, and Table 14, for more information.
Standalone Mode, Time Domain Multiplexed (SA_MODE TDM) State. See the Standalone Mode
section, Table 13, and Table 14, for more information.
DAC11 and DAC 12 Serial Data Input.
DAC9 and DAC 10 Serial Data Input.
DAC7 and DAC 8 Serial Data Input.
DAC5 and DAC 6 Serial Data Input.
DAC3 and DAC 4 Serial Data Input.
DAC1 and DAC 2 Serial Data Input.
Master Output Slave Input (SPI)/Address 1 (I2C)/SA_MODE State (see the Standalone Mode
section and Table 13).
Master Output Slave Input (SPI)/Control Data Input (I2C)/SA_MODE State (see the Standalone
Mode section and Table 13).
Serial Clock Input (SPI)/Control Clock Input (I2C).
Slave Select (SPI) (Active Low)/Address 0 (I2C)/SA_MODE State (see the Standalone Mode
section and Table 13).
Standalone Mode. This pin allows mode control of ADAU1966A using Pin 42, Pin 43, Pin 45,
Pin 31, and Pin 32 (high active). See Table 13 and Table 14 for more information).
Power-Up/Reset (Active Low). See Power-Up and Reset section for more information.
Analog Ground.
Analog Power.
DAC1 Positive Output.
DAC1 Negative Output.
DAC2 Positive Output.
DAC2 Negative Output.
DAC3 Positive Output.
DAC3 Negative Output.
DAC4 Positive Output.
DAC4 Negative Output.
Analog Power.
DAC Bias 1. AC couple Pin 59 with a 470 nF capacitor to AVDD2.
DAC Bias 2. AC couple Pin 60 with a 470 nF capacitor to AGND2.
Analog Ground.
Common-Mode Reference Filter Capacitor Connection. Bypass the CM pin with a 10 μF capacitor
in parallel with a 100 nF capacitor to AGND2. This reference can be shut off in the
PLL_CLK_CTRL1 register (Register 0x01) and the pin can be driven with an outside voltage
source.
Voltage Reference Filter Capacitor Connection. Bypass Pin 63 with a 10 μF capacitor in parallel with a
100 nF capacitor to AGND2.
DAC5 Positive Output.
DAC5 Negative Output.
DAC6 Positive Output.
DAC6 Negative Output.
DAC7 Positive Output.
Rev. A | Page 10 of 52
Data Sheet
Pin No.
69
70
71
72
73
74
75
76
77
78
79
80
Mnemonic1, 2
DAC7N
DAC8P
DAC8N
DAC9P
DAC9N
DAC10P
DAC10N
DAC11P
DAC11N
DAC12P
DAC12N
AGND3
ADAU1966A
Type3
O
O
O
O
O
O
O
O
O
O
O
GND
Description
DAC7 Negative Output.
DAC8 Positive Output.
DAC8 Negative Output.
DAC9 Positive Output.
DAC9 Negative Output.
DAC10 Positive Output.
DAC10 Negative Output.
DAC11 Positive Output.
DAC11 Negative Output.
DAC12 Positive Output.
DAC12 Negative Output.
Analog Ground.
1
AVDD1, AVDD2, AVDD3, and AVDD4 are referred to elsewhere in this document as AVDDx when AVDDx means any or all of the ADVD pins.
DAC Channel 1 to DAC Channel 12 pins are referred to elsewhere in this document as DACx, DACxP, or DACxN when it means any or all of the DAC channel pins.
3
I = input, O = output, I/O = input/output, PWR = power, and GND = ground.
2
Rev. A | Page 11 of 52
ADAU1966A
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0.20
0.05
0.04
0.15
0.03
0.10
MAGNITUDE (dB)
MAGNITUDE (dB)
0.02
0.01
0
–0.01
0.05
0
–0.05
–0.02
–0.10
–0.03
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
FREQUENCY (FACTORED TO fS)
–0.20
0
–20
–20
–30
–30
MAGNITUDE (dB)
0
–10
–40
–50
–60
–80
–90
–90
0.4
0.5
0.6
0.7
0.8
0.9
FREQUENCY (FACTORED TO fS)
0.30
0.35
0.40
1.0
–60
–80
0.3
0.25
–50
–70
0.2
0.20
–40
–70
1.0
11298-005
MAGNITUDE (dB)
0
0.1
0.15
Figure 6. DAC Pass-Band Filter Response, 96 kHz
–10
0
0.10
FREQUENCY (FACTORED TO fS)
Figure 4. DAC Pass-Band Filter Response, 48 kHz
–100
0.05
11298-006
0
11298-004
–0.05
11298-007
–0.15
–0.04
–100
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
FREQUENCY (FACTORED TO fS)
Figure 7. DAC Stop-Band Filter Response, 96 kHz
Figure 5. DAC Stop-Band Filter Response, 48 kHz
Rev. A | Page 12 of 52
Data Sheet
ADAU1966A
TYPICAL APPLICATION CIRCUITS
Typical application circuits are shown in Figure 8 to Figure 13.
Recommended loop filters for DLRCLK and MCLKI/XTALI
modes of the PLL reference are shown in Figure 8. Output filters
for the DAC outputs are shown in Figure 10 to Figure 13, and
an external regulator circuit is shown in Figure 9. When pins for
multiple outputs are referred to generically in this datasheet, there
is an x in place of the number. For example, DACxP refers to
DAC1P through DAC16P.
DLRCLK
LF
VSENSE
2.5V
+
10µF
11298-013
100nF
Figure 9. Recommended 2.5 V Regulator Circuit
DACxP
562Ω
PLLVDD
10µF
+
237Ω
OUTPUTxP
2.7nF
Figure 8. Recommended Loop Filters for DLRCLK and MCLKI/XTALI PLL
Reference Modes
DACxN
10µF
+
237Ω
OUTPUTxN
49.9kΩ
11298-009
49.9kΩ
Figure 10. Typical DAC Output Passive Filter Circuit (Differential)
10µF
2.7nF
OUTPUTxP
49.9kΩ
11298-010
475Ω
+
DACxP
Figure 11. Typical DAC Output Passive Filter Circuit (Single-Ended)
1.1nF
AD8672ARZ
DACxP
1.50kΩ
1.54kΩ
5
7
100Ω
4.7µF
+
OUTPUTxP
6
+12V DC
422Ω
2.49kΩ
100kΩ
8
0.1µF
4.7µF
0.1µF
4.7µF
+
1nF
4.7µF
1nF
4.7µF
+
V+
V–
4
+
+
100kΩ
–12V DC
DACxN
2
1.50kΩ
422Ω
1
1.54kΩ
2.49kΩ
100Ω
3
4.7µF
+
OUTPUTxN
11298-011
AD8672ARZ
1.1nF
Figure 12. Typical DAC Output Active Filter Circuit (Differential)
1.1nF
1.50kΩ
1.54kΩ
AD8672ARZ
4.7µF
100Ω
1nF
422Ω
+
DACxP
100kΩ
2.49kΩ
4.7µF
OUTPUTxP
+
Figure 13. Typical DAC Output Active Filter Circuit (Single-Ended)
Rev. A | Page 13 of 52
11298-012
PLLVDD
FZT953
C
390pF
3.32kΩ
E
B
VDRIVE
5.6nF
2.2nF
3.3V
1kΩ
MCLKI/XTALI
39nF
10µF
+
VSUPPLY
11298-008
LF
100nF
ADAU1966A
Data Sheet
THEORY OF OPERATION
DACs
The 16 ADAU1966A DAC channels are differential for improved
noise and distortion performance and are voltage output for
simplified connection. The DACs include on-chip digital
interpolation filters with 68 dB stop-band attenuation and linear
phase response, operating at an oversampling ratio of 256×
(48 kHz range), 128× (96 kHz range), or 64× (192 kHz range).
Each channel has its own independently programmable
attenuator, adjustable in 255 steps in increments of 0.375 dB.
Digital inputs are supplied through six serial data input pins
(two channels on each pin), a common frame clock (DLRCLK),
and a bit clock (DBCLK). Alternatively, any one of the time domain
multiplexed (TDM) modes can be used to access up to 16 channels
on a single TDM data line.
The ADAU1966A has a low propagation delay mode; this
mode is an option for an fS of 192 kHz and is enabled in Register
DAC_CTRL0[2:1]. By setting these bits to 0b11, the propagation
delay is reduced by the amount listed in Table 6. The shorter delay
is achieved by reducing the amount of digital filtering; the negative
impact of selecting this mode is reduced audio frequency response
and increased out-of-band energy.
power consumption with the trade-off of lower SNR and THD + N.
The reduced power consumption is the result of changing the
internal bias current to the analog output amplifiers.
Register DAC_POWER1 to Register DAC_POWER4 present four
basic settings for the DAC power vs. performance in each of the
16 channels: best performance, good performance, low power, and
lowest power. Alternatively, in Register PLL_CLK_CTRL1[7:6], the
LOPWR_MODE bits offer global control over the power and
performance for all 16 channels. To select the low power or
lowest power settings, set Bit 7 and Bit 6 of the DAC_POWERx
registers to 0b10 or 0b11, respectively. The default setting is 0b00.
This setting allows the channels to be controlled individually
using the DAC_POWERx registers. The data presented in Table 11
shows the result of setting all 16 channels to each of the four
settings. The SNR and THD + N specifications are shown in
relation to the measured performance of a device at the best
performance setting.
The voltage at CM, the common-mode reference pin, can be
used to bias the external op amps that buffer the output signals
(see the Power Supply and Voltage Reference section).
CLOCK SIGNALS
Because AVDDx is supplied with 3.3 V, each analog output pin
has a nominal common-mode (CM) dc level of 1.5 V. With a 0 dB
full-scale digital input signal, each pin swings approximately
±1.42 V peak (2.83 V p-p and 2 V rms). Therefore, the voltage
swing differentially across the two pins is 5.66 V p-p (4 V rms). The
differential analog outputs require a single-order passive differential
resistor-capacitor (RC) filter only to provide the specified DNR
performance; see Figure 10 or Figure 11 for an example filter. The
outputs can easily drive differential inputs on a separate printed
circuit board (PCB) through cabling as well as differential inputs
on the same PCB.
Upon powering the ADAU1966A and asserting the PU/RST pin
high, the part starts in either standalone mode (SA_MODE) or
program mode, depending on the state of SA_MODE (Pin 46).
The clock functionality of SA_MODE is described in the
Standalone Mode section.
If more signal level is required, or if a more robust filter is needed,
a single op amp gain stage designed as a second-order, low-pass
Bessel filter can be used to remove the high frequency out-ofband noise present on each pin of the differential outputs. The
choice of components and design of this circuit is critical to yield
the full DNR of the DACs (see the recommended passive and
active circuits in Figure 10, Figure 11, Figure 12, and Figure 13).
The differential filter can be built into an active difference amplifier
to provide a single-ended output with gain, if necessary. Note that
the use of op amps with low slew rate or low bandwidth can cause
high frequency noise and tones to fold down into the audio
band; exercise care when selecting these components.
The MCLKO pin can be programmed to provide different clock
signals using Register PLL_CLK_CTRL1[5:4]. The default, 0b10,
provides a buffered copy of the clock signal that is driving the
MCLKI pin. Two modes, 0b00 and 0b01, provide low jitter clock
signals.
The ADAU1966A offers control over the analog performance
of the DACs; it is possible to program the registers to reduce the
In program mode, the default for the ADAU1966A is for the
MCLKO pin to feed a buffered output of the MCLKI signal on
the MCLKI/XTALI pin. The default for the DLRCLK and DBCLK
ports is slave mode; the DAC must be driven with a coherent set
of master clock, frame clock, and bit clock signals to function.
The b00 setting yields a clock rate between 4 MHz and 6 MHz,
and the b01 setting yields a clock rate between 8 MHz and 12 MHz.
Both of these clock frequencies are scaled as ratios of the master
clock automatically inside the ADAU1966A. As an example, an
input to MCLKI of 8.192 MHz and a setting of 0b00 yield an
MCLKO of (8.192/2) = 4.096 MHz. Alternatively, an input to
MCLKI of 36.864 MHz and a setting of 0b01 yield an MCLKO
frequency of (36.864/3) = 12.288 MHz. The 0b11 setting disables
the MCLKO pin.
Table 11. DAC Power vs. Performance
Register Setting
Total AVDDx Current
SNR
THD + N (−1 dBFS Signal)
Best Performance
60 mA
Reference
Reference
Good Performance
53 mA
−0.2 dB
−1.8 dB
Rev. A | Page 14 of 52
Low Power
47 mA
−1.5 dB
−3.0 dB
Lowest Power
40 mA
−14.2 dB
−5.8 dB
Data Sheet
ADAU1966A
After the PU/RST pin is asserted high, the PLL_CLK_CTRLx
registers (Register 0x00 and Register 0x01) can be programmed.
The on-chip PLL can be selected to use the clock appearing at the
MCLKI/XTALI pin at a frequency of 256, 384, 512, or 768 times
the sample rate (fS), referenced to the 48 kHz mode from the
master clock select (MCS) setting, as described in Table 12.
In 96 kHz mode, the master clock frequency stays at the same
absolute frequency; therefore, the actual multiplication rate is
divided by 2. In 192 kHz mode, the actual multiplication rate is
divided by 4.
For example, if the ADAU1966A is programmed in 256 × fS
mode, the frequency of the master clock input is 256 × 48 kHz =
12.288 MHz. If the ADAU1966A is then switched to 96 kHz
operation (by writing to DAC_CTRL0[2:1]), the frequency of the
master clock remains at 12.288 MHz, which is an MCS ratio of
128 × fS in this example. Therefore, in 192 kHz mode, MCS
becomes 64 × fS. The internal clock for the digital core varies
by mode: 512 × fS (48 kHz mode), 256 × fS (96 kHz mode), or
128 × fS (192 kHz mode). By default, the on-board PLL generates
this internal master clock from an external clock.
The PLL must be powered and stable before using the
ADAU1966A as a source for quality audio. The PLL is enabled
by reset and does not require writing to the I2C or SPI port for
normal operation.
With the PLL enabled, the performance of the ADAU1966A is
not affected by jitter as high as a 300 ps rms time interval error
(TIE). When the internal PLL is disabled, use an independent
crystal oscillator to generate the master clock.
When using the ADAU1966A in direct master clock mode, power
down the PLL in the PDN_THRMSENS_CTRL_1 register. For
direct master clock mode, a frequency of 512 × fS (referenced to
48 kHz mode) must be fed into the MCLKI pin, and the CLK_SEL
bit in the PLL_CLK_CTRL1 register must be set to 1. However,
for the device to function, 2.5 V power must be connected to
the PLLVDD pin.
The PLL of the ADAU1966A can also be programmed to run
from an external LRCLK without an external master clock. Setting
the PLLIN bits in the PLL_CLK_CTRL0 register to 0b01 and
connecting the appropriate loop filter to the LF pin (see Figure 8),
the ADAU1966A PLL generates all of the necessary internal
clocks for operation with no external master clock. This mode
reduces the number of high frequency signals in the design,
reducing EMI emissions.
It is possible to further reduce EMI emissions of the circuit by
using the internal bit clock generation setting of the BCLK_GEN
bit in the DAC_CTRL1 register. Setting the BCLK_GEN bit to 1
(internal) and the SAI_MS bit to 0 (slave), the ADAU1966A
generates its own bit clock; this configuration works with the
PLL input register (PLL_CLK_CTRL0[7:6]) set to either
MCLKI/XTALI or DLRCLK. The clock on the DLRCLK pin
is the only required clock in DLRCLK PLL mode.
Table 12. MCS and fS Modes
Frequency Sample Select
DAC_CTRL0[2:1]
fS (kHz)
Bit Setting
32 kHz,
44.1 kHz
48 kHz
64 kHz
88.2 kHz
96 kHz
128 kHz
176.4 kHz
192 kHz
0b00
0b00
0b00
0b01
0b01
0b01
0b10 or 0b11
0b10 or 0b11
0b10 or 0b11
Setting 0, 0b00
Master Clock
(MHz)
Ratio
256 × fS 8.192
256 × fS 11.2896
256 × fS 12.288
128 × fS 8.192
128 × fS 11.2896
128 × fS 12.288
64 × fS
8.192
64 × fS
11.2896
64 × fS
12.288
Master Clock Select (MCS), PLL_CLK_CTRL0[2:1]
Setting 1, 0b01
Setting 2, 0b10
Master Clock
Master Clock
(MHz)
(MHz)
Ratio
Ratio
384 × fS 12.288
512 × fS 16.384
384 × fS 16.9344
512 × fS 22.5792
384 × fS 18.432
512 × fS 24.576
192 × fS 12.288
256 × fS 16.384
192 × fS 16.9344
256 × fS 22.5792
192 × fS 18.432
256 × fS 24.576
96 × fS
12.288
128 × fS 16.384
96 × fS
16.9344
128 × fS 22.5792
96 × fS
18.432
128 × fS 24.576
Rev. A | Page 15 of 52
Setting 3, 0b11
Master Clock
(MHz)
Ratio
768 × fS 24.576
768 × fS 33.8688
768 × fS 36.864
384 × fS 24.576
384 × fS 33.8688
384 × fS 36.864
192 × fS 24.576
192 × fS 33.8688
192 × fS 36.864
ADAU1966A
Data Sheet
POWER-UP AND RESET
The power sequencing for the ADAU1966A begins with AVDDx
and IOVDD, followed by DVDD. It is very important that AVDDx
be settled at a regulated voltage and that IOVDD be within 10% of
regulated voltage before applying DVDD. When using the internal
regulator of the ADAU1966A, this timing occurs by default.
To guarantee proper startup, pull the PU/RST pin low by an
external resistor and then drive it high after the power supplies
have stabilized. The PU/RST can also be pulled high using a
simple RC network.
When both SA_MODE (Pin 46) and SS/ADDR0/SA (Pin 45) are
set high, TDM mode is selected. Table 14 shows the available
TDM modes; these modes are set by connecting Pin 31 (SA1) and
Pin 32 (SA2) to GND or IOVDD.
Table 14. TDM Modes
Pin No.
31 to 32
Setting
00
01
10
11
Function
TDM4, DLRCLK pulse
TDM8, DLRCLK pulse
TDM16, DLRCLK pulse
TDM8, DLRCLK 50% duty cycle
Driving the PU/RST pin low puts the part into a very low power
state (<3 μA). All functionality of the ADAU1966A is disabled
until the PU/RST pin is asserted high. Once this pin is asserted
high, the ADAU1966A requires 300 ms to stabilize. The MMUTE
bit in the DAC_CTRL0 register must be toggled for operation.
By powering up the ADAU1966A in SA_MODE, and asserting
the PU/RST pin high, the MCLKO pin provides a buffered version
of the MCLKI/XTALI pin, whether the source is a crystal or an
active oscillator.
The PUP (master power-up control) bit in the PLL_CLK_CTRL0
register can be used to power down the ADAU1966A. Setting
the PUP bit to 0 puts the ADAU1966A in an idle state while
maintaining the settings of all registers. Additionally, the
power-down bits in the PDN_THRMSENS_CTRL_1 register
(TS_PDN, PLL_PDN, and VREG_PDN) can be used to power
down individual sections of the ADAU1966A.
The ADAU1966A has an I2C-compatible control port that permits
programming and readback of the internal control registers for the
DACs and clock system. The I2C interface of the ADAU1966A is a
2-wire interface consisting of a clock line, SCL, and a data line,
SDA. SDA is bidirectional, and the ADAU1966A drives SDA either
to acknowledge the master (ACK) or to send data during a read
operation. The SDA pin (MISO/SDA/SA) for the I2C port is an
open-drain collector and requires a 2 kΩ pull-up resistor. A write
or read access occurs when the SDA line is pulled low while the
SCL line (SCLK/SCL) is high, indicated by a start in Figure 14 and
and Figure 15.
The SOFT_RST bit in the PLL_CLK_CTRL0 register sets all of
the control registers to their default settings while maintaining
the internal clocks in default mode. The SOFT_RST bit does
not power down the analog outputs; nor does toggling this bit
cause audible popping sounds at the differential analog outputs.
For proper startup of the ADAU1966A, follow these steps:
1.
2.
3.
4.
5.
Apply power to the ADAU1966A as described previously
in this Power-Up and Reset section.
Assert the PU/RST pin high after power supplies are stable.
Set the PUP bit to 1.
Program all necessary registers for the desired settings.
Set the MMUTE bit to 0 to unmute all channels.
STANDALONE MODE
The ADAU1966A can operate without a typical I2C or SPI
connection to a microcontroller. This standalone mode is available
by setting SA_MODE (Pin 46) to IOVDD. All registers are set to
default except for the options shown in Table 13.
I2C CONTROL PORT
SDA is only allowed to change when SCL is low, except when a
start or stop condition occurs, as shown in Figure 14 and Figure 15.
The first eight bits of the data-word consist of the device address
and the R/W bit. The device address consists of an internal built-in
address (0x04) and two address bits, ADDR1 and ADDR0. The two
address bits allow four ADAU1966A devices to be used in a system.
Table 15. I2C Addresses
ADDR1 (AD1)
0
0
1
1
Table 13. SA_MODE Settings
Pin No.
42
43
45
Setting
0
1
0
1
0
1
Function
Master mode serial audio interface (SAI)
Slave mode SAI
MCLK = 256 × fS, PLL on
MCLK = 384 × fS, PLL on
I2S SAI format
TDM modes, determined by Pin 31 and Pin 32
Rev. A | Page 16 of 52
ADDR0 (AD0)
0
1
0
1
Slave Address
0x04
0x24
0x44
0x64
Data Sheet
ADAU1966A
I2C Write
3.
Initiating a write operation to the ADAU1966A involves the
following steps (see Figure 14):
1.
2.
4.
Send a start condition
Send the device address with the R/W bit set low.
a. The ADAU1966A responds by issuing an
acknowledge to indicate that it has been addressed.
5.
Send a second frame directing the ADAU1966A to which
register is required to be written.
a. A second acknowledge is issued by the ADAU1966A.
Send a third frame with the eight data bits required to be
written to the register.
a. A third acknowledge is issued by the ADAU1966A.
Send a stop condition to complete the data transfer.
SCL
SDA
AD1
AD0
0
0
1
0
0
START BY
MASTER (S)
R/W
0
0
0
0
0
1
1
0
ACK. BY
ADAU1966A (AS)
ACK. BY
ADAU1966A (AS)
FRAME 1
CHIP ADDRESS BYTE
FRAME 2
REGISTER ADDRESS BYTE
SCL
(CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0
ACK. BY STOP BY
ADAU1966A (AS) MASTER (P)
FRAME 3
DATA BYTE TO ADAU1966A
11298-014
SDA
(CONTINUED)
2
Figure 14. I C Write Format
2
Table 16. I C Abbreviations
Abbreviation
S
P
AM
AS
Condition
Start bit
Stop bit
Acknowledge by master
Acknowledge by slave
Table 17. Single Word I2C Write
S
AS
Chip Address, R/W = 0
Register Address
AS
Data-Word
AS
P
Table 18. Burst Mode I2C Write
S
Chip Address, R/W = 0
AS
Register Address
AS
Data-Word 1
Rev. A | Page 17 of 52
AS
Data-Word 2
AS
Data-Word N
AS
P
ADAU1966A
Data Sheet
I2C Read
A read operation requires that the user first write to the
ADAU1966A to point to the correct register and then read
the data. The following steps achieve this (see Figure 15):
1.
2.
Send a start condition followed by the device address frame
with the R/W bit low and then the register address frame.
a. The ADAU1966A responds with an acknowledge.
Issue a repeated start condition.
a. The next frame is the device address with the R/W bit
set high.
b. On the next frame, the ADAU1966A outputs the
register data on the SDA line.
Issue a stop condition to complete the read operation.
3.
Table 19. Single Word I2C Read
S
AS
Chip Address, R/W = 0
Register Address
AS
S
AS
Chip Address, R/W = 1
Data-Word
AM
P
Table 20. Burst Mode I2C Read
S
Chip Address,
R/W = 0
AS
AS
Register
Address
S
Chip Address,
R/W = 1
AS
DataWord 1
AM
DataWord 2
0
0
AM
DataWord N
AM
P
SCL
SDA
AD1
AD0
0
0
1
0
0
START BY
MASTER (S)
R/W
0
0
0
1
1
ACK. BY
ADAU1966A (AS)
0
ACK. BY
ADAU1966 A (AS)
FRAME 1
CHIP ADDRESS BYTE
FRAME 2
REGISTER ADDRESS BYTE
SCL
(CONTINUED)
AD1
REPEATED START
BY MASTER (S)
AD0
0
0
1
0
FRAME 3
CHIP ADDRESS BYTE
0
R/W
D7
ACK. BY
ADAU1966 A (AS)
Figure 15. I2C Read Format
Rev. A | Page 18 of 52
D6
D5
D4
D3
FRAME 4
REGISTER DATA
D2
D1
D0
ACK. BY STOP BY
MASTER (AM) MASTER (P)
11298-015
SDA
(CONTINUED)
Data Sheet
ADAU1966A
The format is a 24-bit wide data-word. The serial bit clock and
latch can be completely asynchronous to the sample rate of the
DACs. The first byte is a global address with a read/write bit. For
the ADAU1966A, the address is 0x06, shifted left one bit due to
the R/W bit. The second byte is the ADAU1966A register address,
and the third byte is the data, as shown in Figure 17 and Figure 18.
When reading data from the ADAU1966A, MISO is tristated
until the third byte where it drives data out (see Figure 18). MISO
is tristated at all other times, allowing it to be bused with other
devices. The timing requirements are shown in Figure 19.
SERIAL CONTROL PORT: SPI CONTROL MODE
The ADAU1966A has a 4-wire SPI control port that permits the
programming and reading back of the internal control registers
for the DACs and clock system. A standalone mode is also
available for operation without serial control; it is configured at
reset using the SA_MODE pin. See the Standalone Mode section
for details about the SA_MODE pin.
By default, the ADAU1966A is in I2C mode; however, it can be
put into SPI control mode by pulling SS low three times. This
is done by performing three dummy writes to the SPI port
(the ADAU1966A does not acknowledge these three writes,
see Figure 16). Beginning with the fourth SPI write, data can
be written to or read from the IC. The ADAU1966A can only
be taken out of SPI control mode by a full reset initiated by
power cycling the device.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
SS
11298-016
SCLK
MOSI
Figure 16. SPI Mode Initial Sequence
0
1
2
3
4
5
6
7
8
9
10
11
12
13
15
14
16
17
18
19
20
21
22
23
24
25
SS
DEVICE ADDRESS (7 BITS)
R/W
REGISTER ADDRESS BYTE
MOSI
11298-017
SCLK
DATA BYTE
Figure 17. SPI Write to ADAU1966A Clocking
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
SCLK
SS
DEVICE ADDRESS (7 BITS)
MOSI
REGISTER ADDRESS BYTE
DATA BYTE
11298-018
R/W
DATA BYTE FROM ADAU1966A
MISO
Figure 18. SPI Read from ADAU1966A Clocking
tSSH
tSSS
tMIE
tSCH
SS
tSSHIGH
tSCL
SCLK
MOSI
tMOH
tMOS
MISO
tMID
Figure 19. SPI Signal Timing
Rev. A | Page 19 of 52
11298-019
tMITS
ADAU1966A
Data Sheet
Chip Address R/W
The LSB of the first byte of an SPI transaction is a R/W bit. This bit
determines whether the communication is a read (Logic Level 1)
or a write (Logic Level 0). This format is shown in Table 21.
Table 21. ADAU1966A SPI Address and R/W Byte Format
Bit 0
0
Bit 1
0
Bit 2
0
Bit 3
0
Bit 4
1
Bit 5
1
Bit 6
0
Bit 7
R/W
SPI Burst Read/Write
The SPI port is capable of performing burst reads or writes by
sending the chip address byte with the R/W bit followed by the
first register address that needs to be read from or written to.
Then, as long as the SS pin is held low, the user can sequentially
read from or write to the registers by continuing to send clock
pulses into the SCLK pin. An efficient way to initialize the
ADAU1966A is by





Sending out the address byte with the R/W bit low (write)
Sending out the address of the first register
Sending out all the register byte values
Toggling SS to end the transfer
Performing a burst read to verify that the register writes
were successful
When referencing back to Analog Devices legacy devices, different
pin names (mnemonics) were used for these SPI port functions.
See Table 22 for details of the changes.
Table 22. SPI Port Pin Naming Conventions
Pin No.
42
43
44
45
Legacy Pin Mnemonic
CDATA
COUT
CCLK
CLATCH
New Pin Mnemonic
MOSI
MISO
SCLK
SS
POWER SUPPLY AND VOLTAGE REFERENCE
The ADAU1966A is designed for 3.3 V analog and 2.5 V digital
supplies. To minimize noise pickup, bypass the power supply
pins with 100 nF ceramic chip capacitors placed as close to the
pins as possible. Provide a bulk aluminum electrolytic capacitor
of at least 22 μF for each rail on the same PCB as the codec. It is
important that the analog supply be as clean as possible.
The ADAU1966A includes a 2.5 V regulator driver that requires
only an external pass transistor and bypass capacitors to make a
2.5 V regulator from a 3.3 V supply. Decouple the VSUPPLY
and VSENSE pins with no more than 10 μF of capacitance in
parallel with 100 nF high frequency bypassing. If the regulator
driver is not used, connect VSUPPLY and VDRIVE to GND
and leave VSENSE unconnected.
The temperature sensor internal voltage reference (VTS_REF) is
connected to the TS_REF pin and must be bypassed as close as
possible to the chip with a parallel combination of 10 μF and
100 nF capacitors.
The internal band gap reference can be disabled in the
PLL_CLK_CTRL1 register by setting VREF_EN to 0; the CM
pin can be then be driven from an external source. This can be
used to scale the DAC output to the clipping level of a power
amplifier based on its power supply voltage.
The CM pin is the internal common-mode reference. Bypass it
as close as possible to the chip with a parallel combination of
10 μF and 100 nF capacitors. This voltage can be used to bias
external op amps to the common-mode voltage of the analog
input and output signal pins. It is recommended that the CM pin
be isolated from the external circuitry by using a high quality
buffer to provide a quiet, low impedance source for the external
circuitry. Use of a quiet op amp is critical because any noise added
to the reference voltage is injected into the signal path.
SERIAL DATA PORTS—DATA FORMAT
The 16 DAC channels use a common serial bit clock (DBCLK)
and a common left-right framing clock (DLRCLK) in the serial
data port. The clock signals are all synchronous with the sample
rate. The normal stereo serial modes are shown in Figure 20.
The DAC serial data mode defaults to I2S (1 BCLK delay) upon
power-up and reset. The ports can also be programmed for left
justified and right justified (24-bit and 16-bit) operation using
DAC_CTRL0[7:6]. Stereo and TDM modes can be selected using
DAC_CTRL0[5:3]. The polarity of DBCLK and DLRCLK is
programmable according to the DAC_CTRL1[1] and DAC_
CTRL1[5] bits. The serial ports are programmable as the clock
masters according to the DAC_CTRL1[0] bit. By default, the
serial port is in slave mode.
Rev. A | Page 20 of 52
Data Sheet
ADAU1966A
LEFT CHANNEL
DLRCLK
RIGHT CHANNEL
BCLK
DSDATAx
LSB
MSB
LSB
MSB
LEFT-JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL: SAI = 0, SDATA_FMT = 1
LEFT CHANNEL
DLRCLK
RIGHT CHANNEL
DBCLK
DSDATAx
LSB
MSB
LSB
MSB
I2S-JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL: SAI = 0, SDATA_FMT = 0
LEFT CHANNEL
DLRCLK
RIGHT CHANNEL
DBCLK
DSDATAx
LSB
MSB
LSB
MSB
RIGHT-JUSTIFIED MODE—SELECT NUMBER OF BITS PER CHANNEL: SAI = 0, SDATA_FMT = 2 OR 3
DLRCLK
DBCLK
MSB
MSB
LSB
TDM MODE—16 BITS TO 24 BITS PER CHANNEL: SAI = 1, 2, 3, OR 4
1/fS
LSB
11371-020
DSDATAx
Figure 20. Stereo Serial Audio Modes
The ADAU1966A serial ports also have several different TDM
serial data modes. The ADAU1966A can support a single data
line (TDM16), a dual data line (TDM8), a quad data line (TDM4),
or eight data lines (TDM2). The DLRCLK/frame clock can
operate in both single-cycle pulse mode and a 50% duty cycle
mode. Both 16 DBCLKs and 32 DBCLKs per channel are
selectable for each mode.
PDN_THRMSENS_CTRL_1 register. The temperature sensor
can be run in either continuous operation or one-shot mode.
The temperature sensor conversion mode is modified using
THRM_MODE (Bit 5); the default is THRM_MODE = 1, oneshot mode. In one-shot mode, writing a 0 followed by writing a 1 to
THRM_GO (Bit 4), results in a single reset and temperature
conversion, placing the resulting temperature data in the THRM_
TEMP_STAT register.
The I/O pins of the serial ports are defined according to the serial
mode that is selected. For a detailed description of the function
of each pin in TDM and stereo modes, see Table 23.
In continuous operation mode, the data conversion takes place
at a rate set by THRM_RATE[7:6], with a range of 0.5 sec to 4 sec
between samples. Faster rates are possible using one-shot mode.
TEMPERATURE SENSOR
Once a temperature conversion is placed in the THRM_TEMP_
STAT register, the data can be translated into degrees Celsius (°C)
using the following steps:
TIME-DIVISION MULTIPLEXED (TDM) MODES
The ADAU1966A has an on-board temperature sensor that allows
the user to read the temperature of the silicon inside the device.
The temperature sensor readout has a range of −60°C to +140°C
in 1°C steps. The PDN_THRMSENS_CTRL_1 register controls
the settings of the sensor. The temperature sensor is powered on by
default and can be shut off by setting the TS_PDN[2] bit to 1 in the
1.
2.
Rev. A | Page 21 of 52
Convert the binary or hexadecimal data read from
THRM_TEMP_STAT into decimal form.
Subtract 60 from the converted THRM_TEMP_STAT data;
this is the temperature of the silicon in °C.
ADAU1966A
Data Sheet
tDBH
DBCLK
tDBL
tDLH
tDLS
DLRCLK
DSDATAx
LEFT JUSTIFIED
MODE
tDDS
MSB
MSB – 1
tDDH
tDDS
DSDATAx
I2S-JUSTIFIED
MODE
MSB
tDDH
tDDS
MSB
LSB
tDDH
tDDH
11298-021
tDDS
DSDATAx
RIGHT JUSTIFIED
MODE
Figure 21. DAC Serial Timing
Table 23. Pin Function Changes in Different Serial Audio Interface Modes
Signal
DSDATA1
Stereo Modes (SAI = 0 or SAI = 1)
Channel 1/Channel 2 data input
DSDATA2
Channel 3/Channel 4 data input
DSDATA3
Channel 5/Channel 6 data input
DSDATA4
Channel 7/Channel 8 data input
DSDATA5
DSDATA6
DSDATA7
DSDATA8
DLRCLK
Channel 9/Channel 10 data input
Channel 11/Channel 12 data input
Channel 13/Channel 14 data input
Channel 15/Channel 16 data input
DLRCLK input/DLRCLK output
DBCLK
DBCLK input/DBCLK output
Maximum Sample Rate
192 kHz
TDM4 Mode (SAI = 2)
Channel 1 to Channel 4
data input
Channel 5 to Channel 8
data input
Channel 9 to Channel 12
data input
Channel 13 to Channel 16
data input
Not used
Not used
Not used
Not used
TDM frame sync input/
TDM frame sync output
TDM DBCLK input/
TDM DBCLK output
192 kHz
Rev. A | Page 22 of 52
TDM8 Mode (SAI = 3)
Channel 1 to Channel 8
data input
Channel 9 to Channel 16
data input
Not used
TDM16 Mode (SAI = 4)
Channel 1 to Channel 16
data input
Not used
Not used
Not used
Not used
Not used
Not used
Not used
TDM frame sync input/
TDM frame sync output
TDM DBCLK input/
TDM DBCLK output
96 kHz
Not used
Not used
Not used
Not used
TDM frame sync input/
TDM frame sync output
TDM DBCLK input/
TDM DBCLK output
48 kHz
Not used
Data Sheet
ADAU1966A
ADDITIONAL MODES
The ADAU1966A offers several additional modes for board level
design enhancements. To reduce the EMI in board level design,
serial data can be transmitted without an explicit bit clock input
on the DBCLK pin. See Figure 22 for an example of a DAC TDM
data transmission mode that does not require a high speed bit clock
or an external master clock. This configuration is applicable
when the ADAU1966A master clock is generated by the PLL
with the DLRCLK pin as the PLL reference frequency.
To relax the requirement for the setup time of the ADAU1966A in
cases of high speed TDM data transmission, the ADAU1966A
can latch in the data using the falling edge of DBCLK pin; see
the BCLK_EDGE bit in the DAC_CTRL1 register. This effectively
dedicates the entire bit clock period to the setup time. This
mode is useful when the source has a large delay time in the serial
data driver. Figure 23 shows this inverted bit clock mode of data
transmission.
DLRCLK
32 BITS
INTERNAL
DBCLK
DSDATAx
DLRCLK
11298-022
INTERNAL
DBCLK
TDM DSDATAx
Figure 22. Serial DAC Data Transmission in TDM Format Without DBCLK (Applicable Only If PLL Locks to DLRCLK)
DLRCLK
DBCLK
DSDATAx
11298-023
DATA MUST BE VALID
AT THIS BCLK EDGE
MSB
Figure 23. Inverted DBCLK Mode in DAC Serial Data Transmission (Applicable in Stereo and TDM, Useful for High Frequency TDM Transmission)
Rev. A | Page 23 of 52
ADAU1966A
Data Sheet
REGISTER SUMMARY
Table 24. ADAU1966A Register Summary
Reg. No.
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
Register Name
PLL_CLK_CTRL0
PLL_CLK_CTRL1
PDN_THRMSENS_CTRL_1
PDN_CTRL2
PDN_CTRL3
THRM_TEMP_STAT
DAC_CTRL0
DAC_CTRL1
DAC_CTRL2
DAC_MUTE1
DAC_MUTE2
DACMSTR_VOL
DAC01_VOL
DAC02_VOL
DAC03_VOL
DAC04_VOL
DAC05_VOL
DAC06_VOL
DAC07_VOL
DAC08_VOL
DAC09_VOL
DAC10_VOL
DAC11_VOL
DAC12_VOL
DAC13_VOL
DAC14_VOL
DAC15_VOL
DAC16_VOL
PAD_STRGTH
DAC_POWER1
DAC_POWER2
DAC_POWER3
DAC_POWER4
Bits
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
Bit 7
Bit 6
PLLIN
LOPWR_MODE
THRM_RATE
DAC08_PDN DAC07_PDN
DAC16_PDN DAC15_PDN
Bit 5
Bit 4
XTAL_SET
MCLKO_SEL
THRM_MODE THRM_GO
DAC06_PDN DAC05_PDN
DAC14_PDN DAC13_PDN
Reset
0x00
0x2A
0xA0
0x00
0x00
0x00
SDATA_FMT
SAI
FS
MMUTE
0x01
BCLK_GEN
LRCLK_MODE LRCLK_POL
SAI_MSB
RESERVED
BCLK_RATE
BCLK_EDGE SAI_MS
0x00
RESERVED
BCLK_TDMC DAC_POL
AUTO_MUTE_EN DAC_OSR
DE_EMP_EN 0x06
DAC08_MUTE DAC07_MUTE DAC06_MUTE DAC05_MUTE DAC04_MUTE DAC03_MUTE
DAC02_MUTE DAC01_MUTE 0x00
DAC16_MUTE DAC15_MUTE DAC14_MUTE DAC13_MUTE DAC12_MUTE DAC11_MUTE
DAC10_MUTE DAC09_MUTE 0x00
DACMSTR_VOL
0x00
DAC01_VOL
0x00
DAC02_VOL
0x00
DAC03_VOL
0x00
DAC04_VOL
0x00
DAC05_VOL
0x00
DAC06_VOL
0x00
DAC07_VOL
0x00
DAC08_VOL
0x00
DAC09_VOL
0x00
DAC10_VOL
0x00
DAC11_VOL
0x00
DAC12_VOL
0x00
DAC13_VOL
0x00
DAC14_VOL
0x00
DAC15_VOL
0x00
DAC16_VOL
0x00
RESERVED
RESERVED
PAD_DRV
0x00
DAC04_POWER
DAC03_POWER
DAC02_POWER
DAC01_POWER
0xAA
DAC08_POWER
DAC07_POWER
DAC06_POWER
DAC05_POWER
0xAA
DAC12_POWER
DAC11_POWER
DAC10_POWER
DAC09_POWER
0xAA
DAC16_POWER
DAC15_POWER
DAC14_POWER
DAC13_POWER
0xAA
Rev. A | Page 24 of 52
Bit 3
SOFT_RST
PLL_MUTE
RESERVED
DAC04_PDN
DAC12_PDN
TEMP
Bit 2
Bit 1
MCS
PLL_LOCK
VREF_EN
TS_PDN
PLL_PDN
DAC03_PDN
DAC02_PDN
DAC11_PDN
DAC10_PDN
Bit 0
PUP
CLK_SEL
VREG_PDN
DAC01_PDN
DAC09_PDN
RW
RW
RW
RW
RW
RW
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Data Sheet
ADAU1966A
REGISTER DETAILS
PLL AND CLOCK CONTROL 0 REGISTER
Address: 0x00, Reset: 0x00, Name: PLL_CLK_CTRL0
Table 25. Bit Descriptions for PLL_CLK_CTRL0
Bits
[7:6]
Bit Name
PLLIN
Settings
00
01
10
11
[5:4]
XTAL_SET
00
01
10
11
3
SOFT_RST
0
1
[2:1]
MCS
00
01
10
11
0
PUP
0
1
Description
PLL Input Select. Selects between MCLKI/XTALI and DLRCLK as the input to the PLL.
MCLKI or XTALI.
DLRCLK.
Reserved.
Reserved.
XTAL Oscillator Setting. XTALO pin status.
XTAL oscillator enabled.
Reserved.
Reserved.
XTALO Off.
Reset
0x0
Access
RW
0x0
RW
Software Reset Control. This bit resets all circuitry inside the IC, except I2C/SPI
communications. All control registers are reset to default values, except Register 0x00
and Register 0x01. The PLL_CLK_CTRLx registers do not change state.
Normal Operation.
Device in Reset.
0x0
RW
Master Clock Select. MCLKI/XTALI pin functionality (PLL active), master clock rate setting.
The following values are for the fS rate range from 32 kHz to 48 kHz. See Table 12 for
details when using other fS selections.
256 × fS MCLK (44.1 kHz or 48 kHz).
384 × fS MCLK (44.1 kHz or 48 kHz).
512 × fS MCLK (44.1 kHz or 48 kHz).
768 × fS MCLK (44.1 kHz or 48 kHz).
Master Power-Up Control. This bit must be set to 1 as the first register write to power up
the IC.
Master Power-Down.
Master Power-Up.
0x0
RW
0x0
RW
Rev. A | Page 25 of 52
ADAU1966A
Data Sheet
PLL AND CLOCK CONTROL 1 REGISTER
Address: 0x01, Reset: 0x2A, Name: PLL_CLK_CTRL1
B7
B6
B5
B4
B3
B2
B1
B0
0
0
1
0
1
0
1
0
[7:6] LOPWR_MODE
[0] CLK_SEL
Global Power/Performance Adjust
DAC Clock Select
00: I2C Register Settings
01: Reserved
10: Lower Power
11: Lowest Power
0: MCLK from PLL
1: MCLK from MCLKI or XTALI
[1] VREF_EN
Internal Voltage Reference Enable
0: Disabled
[5:4] MCLKO_SEL
1: Enabled
MCLK Output Frequency
00: MCLKO = 4 MHz to 6 MHz scaled by fs
01: MCLKO = 8 MHz to 12 MHz scaled by fs
[2] PLL_LOCK
PLL Lock Indicator
10: MCLKO = Buffered MCLKI
11: MCLKO Pin Disabled
0: PLL Not Locked
1: PLL Locked
[3] PLL_MUTE
PLL Automute Enable/Lock
0: No DAC Automute
1: DAC Automute on PLL Unlock
Table 26. Bit Descriptions for PLL_CLK_CTRL1
Bits
[7:6]
Bit Name
LOPWR_MODE
Settings
00
01
10
11
[5:4]
MCLKO_SEL
00
01
10
11
3
PLL_MUTE
0
1
2
PLL_LOCK
0
1
1
VREF_EN
0
1
0
CLK_SEL
0
1
Description
Global Power/Performance Adjust. These bits adjust the power consumption and
performance level for all 16 DAC channels at once. See the DACs section for more details.
I2C Register Settings.
Reserved.
Lower Power.
Lowest Power.
MCLK Output Frequency. Frequency selection for MCLKO pin. See the Clock Signals
section for more details.
MCLKO = 4 MHz to 6 MHz scaled by fS.
MCLKO = 8 MHz to 12 MHz scaled by fS.
MCLKO = Buffered MCLKI.
MCLKO Pin Disabled.
PLL Automute Enable/Lock. This bit enables the PLL lock automute function.
No DAC Automute.
DAC Automute on PLL Unlock.
PLL Lock Indicator.
PLL Not Locked.
PLL Locked.
Internal Voltage Reference Enable. The internal voltage reference powers the
common mode for the ADAU1966A. Disabling this bit allows the user to drive the
CM pin with an outside voltage source.
Disabled.
Enabled.
DAC Clock Select. Selects between PLL and direct MCLK mode.
MCLK from PLL.
MCLK from MCLKI or XTALI.
Rev. A | Page 26 of 52
Reset
0x0
Access
RW
0x2
RW
0x1
RW
0x0
R
0x1
RW
0x0
RW
Data Sheet
ADAU1966A
BLOCK POWER-DOWN AND THERMAL SENSOR CONTROL 1 REGISTER
Address: 0x02, Reset: 0xA0, Name: PDN_THRMSENS_CTRL_1
Table 27. Bit Descriptions for PDN_THRMSENS_CTRL_1
Bits
[7:6]
Bit Name
THRM_RATE
Settings
00
01
10
11
5
THRM_MODE
0
1
4
THRM_GO
0
1
2
TS_PDN
0
1
1
PLL_PDN
0
1
0
VREG_PDN
0
1
Description
Conversion Time Interval. When THRM_MODE = 0, the THRM_RATE bits control the
time interval between temperature conversions.
4 sec/Conversion.
0.5 sec/Conversion.
1 sec/Conversion.
2 sec/Conversion.
Continuous vs. One-Shot. Determines if the temperature conversions occur
continuously or only when commanded. To perform one-shot temperature
conversions, set this bit to 1.
Continuous Operation.
One-Shot Mode.
One-Shot Conversion Mode. When in one-shot conversion mode, THRM_MODE = 1,
the THRM_GO bit must be set to 0 followed by a write of 1. This sequence results in a
single temperature conversion. The temperature data is available 120 ms after writing
a 1 to this bit.
Reset.
Convert Temperature.
Temperature Sensor Power-Down.
Temperature Sensor On.
Temperature Sensor Power-Down.
PLL Power-Down.
PLL Normal Operation.
PLL Power-Down.
Voltage Regulator Power-Down.
Voltage Regulator Normal Operation.
Voltage Regulator Power-Down.
Rev. A | Page 27 of 52
Reset
0x2
Access
RW
0x1
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
ADAU1966A
Data Sheet
POWER-DOWN CONTROL 2 REGISTER
Address: 0x03, Reset: 0x00, Name: PDN_CTRL2
Table 28. Bit Descriptions for PDN_CTRL2
Bits
7
Bit Name
DAC08_PDN
Settings
0
1
6
DAC07_PDN
0
1
5
DAC06_PDN
0
1
4
DAC05_PDN
0
1
3
DAC04_PDN
0
1
2
DAC03_PDN
0
1
1
DAC02_PDN
0
1
0
DAC01_PDN
0
1
Description
Channel 8 Power-Down
Normal Operation
Power-Down Channel 8
Channel 7 Power-Down
Normal Operation
Power-Down Channel 7
Channel 6 Power-Down
Normal Operation
Power-Down Channel 6
Channel 5 Power-Down
Normal Operation
Power-Down Channel 5
Channel 4 Power-Down
Normal Operation
Power-Down Channel 4
Channel 3 Power-Down
Normal Operation
Power-Down Channel 3
Channel 2 Power-Down
Normal Operation
Power-Down Channel 2
Channel 1 Power-Down
Normal Operation
Power-Down Channel 1
Rev. A | Page 28 of 52
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
Data Sheet
ADAU1966A
POWER-DOWN CONTROL 3 REGISTER
Address: 0x04, Reset: 0x00, Name: PDN_CTRL3
Table 29. Bit Descriptions for PDN_CTRL3
Bits
7
Bit Name
DAC16_PDN
Settings
0
1
6
DAC15_PDN
0
1
5
DAC14_PDN
0
1
4
DAC13_PDN
0
1
3
DAC12_PDN
0
1
2
DAC11_PDN
0
1
1
DAC10_PDN
0
1
0
DAC09_PDN
0
1
Description
Channel 16 Power-Down
Normal Operation
Power-Down Channel 16
Channel 15 Power-Down
Normal Operation
Power-Down Channel 15
Channel 14 Power-Down.
Normal Operation
Power-Down Channel 14
Channel 13 Power-Down.
Normal Operation
Power-Down Channel 13
Channel 12 Power-Down
Normal Operation
Power-Down Channel 12
Channel 11 Power-Down
Normal Operation
Power-Down Channel 11
Channel 10 Power-Down
Normal Operation
Power-Down Channel 10
Channel 9 Power-Down
Normal Operation
Power-Down Channel 9
Rev. A | Page 29 of 52
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
ADAU1966A
Data Sheet
THERMAL SENSOR TEMPERATURE READOUT REGISTER
Address: 0x05, Reset: 0x00, Name: THRM_TEMP_STAT
Table 30. Bit Descriptions for THRM_TEMP_STAT
Bits
[7:0]
Bit Name
TEMP
Settings
Description
Thermal Sensor Temperature Readout. −60°C to +140°C range, 1°C step size. To
convert the hexadecimal or binary TEMP value into decimal form, use the following
equation: (TEMP − 60). The result is the temperature in degrees Celsius.
Reset
0x00
Access
R
DAC CONTROL 0 REGISTER
Address: 0x06, Reset: 0x01, Name: DAC_CTRL0
Table 31. Bit Descriptions for DAC_CTRL0
Bits
[7:6]
Bit Name
SDATA_FMT
Settings
00
01
10
11
[5:3]
SAI
000
001
010
011
100
101
110
111
Description
SDATA Format. Only used when SAI = 000.
I2S, 1 BCLK Cycle Delay.
Left Justified, 0 BCLK Cycle Delay.
Right Justified, 24-Bit Data, 8 BCLK Cycle Delay.
Right Justified, 16-Bit Data, 16 BCLK Cycle Delay.
Serial Audio Interface. When SAI = 000, the SDATA_FMT bits control stereo SDATA format.
Stereo (I2S, LJ, RJ).
TDM2—Octal Line.
TDM4—Quad Line.
TDM8—Dual Line.
TDM16—Single Line (48 kHz).
Reserved.
Reserved.
Reserved.
Rev. A | Page 30 of 52
Reset
0x0
Access
RW
0x0
RW
Data Sheet
Bits
[2:1]
Bit Name
FS
ADAU1966A
Settings
Description
Sample Rate Select.
32 kHz/44.1 kHz/48 kHz.
64 kHz/88.2 kHz/96 kHz.
128 kHz/176.4 kHz/192 kHz.
128 kHz/176.4 kHz/192 kHz Low Propagation Delay.
DAC Master Mute.
Normal Operation.
All Channels Muted.
00
01
10
11
0
MMUTE
0
1
Reset
0x0
Access
RW
0x1
RW
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
DAC CONTROL 1 REGISTER
Address: 0x07, Reset: 0x00, Name: DAC_CTRL1
Table 32. Bit Descriptions for DAC_CTRL1
Bits
7
Bit Name
BCLK_GEN
Settings
0
1
6
LRCLK_MODE
0
1
5
LRCLK_POL
0
1
4
SAI_MSB
0
1
2
BCLK_RATE
0
1
Description
DBCLK Generation. When the PLL is locked to DLRCLK, it is possible to run the
ADAU1966A without an external DBCLK.
Normal Operation—DBCLK.
Internal DBCLK Generation.
DLRCLK Mode Select. Only Valid for TDM modes.
50% Duty Cycle DLRCLK.
Pulse Mode.
DLRCLK Polarity. Allows the swapping of data between channels.
Left/Odd channels are DLRCLK Low (Normal).
Left/Odd channels are DLRCLK High (Inverted).
MSB Position.
MSB First DSDATA.
LSB First DSDATA.
DBCLK Rate. Number of DBCLK cycles per DLRCLK frame. Used only for generating
DBCLK in master mode operation (SAI_MS = 1).
32 Cycles per Frame.
16 Cycles per Frame.
Rev. A | Page 31 of 52
ADAU1966A
Bits
1
Bit Name
BCLK_EDGE
Data Sheet
Settings
0
1
0
SAI_MS
0
1
Description
DBCLK Active Edge. Adjust the polarity of the DBCLK leading edge.
Latch in Rising Edge.
Latch in Falling Edge.
Serial Interface Master. Both DLRCLK and DBCLK become the master when enabled.
DLRCLK/DBCLK Slave.
DLRCLK/DBCLK Master.
Reset
0x0
Access
RW
0x0
RW
DAC CONTROL 2 REGISTER
Address: 0x08, Reset: 0x06, Name: DAC_CTRL2
Table 33. Bit Descriptions for DAC_CTRL2
Bits
4
Bit Name
BCLK_TDMC
Settings
0
1
3
DAC_POL
0
1
2
AUTO_MUTE_EN
0
1
1
DAC_OSR
0
1
0
DE_EMP_EN
0
1
Description
DBCLK Rate in TDM Mode. Number of DBCLK cycles per channel slot when
in TDM mode.
32 BCLK cycles/channel slot.
16 BCLK cycles/channel slot.
DAC Output Polarity. This is a global switch of DAC polarity.
Noninverted DAC Output.
Inverted DAC Output.
Automute Enable. Automatically mutes the DACs when 1024 consecutive
zero input samples are received. This is independent per channel.
Auto-Zero Input Mute Disabled.
Auto-Zero Input Mute Enabled.
DAC Oversampling Rate. OSR selection.
256 × fS DAC Oversampling.
128 × fS DAC Oversampling.
De-Emphasis Enable.
No De-Emphasis/Flat.
De-Emphasis Enabled.
Rev. A | Page 32 of 52
Reset
0x0
Access
RW
0x0
RW
0x1
RW
0x1
RW
0x0
RW
Data Sheet
ADAU1966A
DAC INDIVIDUAL CHANNEL MUTES 1 REGISTER
Address: 0x09, Reset: 0x00, Name: DAC_MUTE1
Table 34. Bit Descriptions for DAC_MUTE1
Bits
7
Bit Name
DAC08_MUTE
Settings
0
1
6
DAC07_MUTE
0
1
5
DAC06_MUTE
0
1
4
DAC05_MUTE
0
1
3
DAC04_MUTE
0
1
2
DAC03_MUTE
0
1
1
DAC02_MUTE
0
1
0
DAC01_MUTE
0
1
Description
DAC8 Soft Mute
DAC8 Normal Operation
DAC8 Muted
DAC7 Soft Mute
DAC7 Normal Operation
DAC7 Muted
DAC6 Soft Mute
DAC6 Normal Operation
DAC6 Muted
DAC5 Soft Mute
DAC5 Normal Operation
DAC5 Muted
DAC4 Soft Mute
DAC4 Normal Operation
DAC4 Muted
DAC3 Soft Mute
DAC3 Normal Operation
DAC3 Muted
DAC2 Soft Mute
DAC2 Normal Operation
DAC2 Muted
DAC1 Soft Mute
DAC1 Normal Operation
DAC1 Muted
Rev. A | Page 33 of 52
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
ADAU1966A
Data Sheet
DAC INDIVIDUAL CHANNEL MUTES 2 REGISTER
Address: 0x0A, Reset: 0x00, Name: DAC_MUTE2
Table 35. Bit Descriptions for DAC_MUTE2
Bits
7
Bit Name
DAC16_MUTE
Settings
0
1
6
DAC15_MUTE
0
1
5
DAC14_MUTE
0
1
4
DAC13_MUTE
0
1
3
DAC12_MUTE
0
1
2
DAC11_MUTE
0
1
1
DAC10_MUTE
0
1
0
DAC09_MUTE
0
1
Description
DAC16 Soft Mute
DAC16 Normal Operation
DAC16 Muted
DAC15 Soft Mute
DAC15 Normal Operation
DAC15 Muted
DAC14 Soft Mute
DAC14 Normal Operation
DAC14 Muted
DAC13 Soft Mute
DAC13 Normal Operation
DAC13 Muted
DAC12 Soft Mute
DAC12 Normal Operation
DAC12 Muted
DAC11 Soft Mute
DAC11 Normal Operation
DAC11 Muted
DAC10 Soft Mute
DAC10 Normal Operation
DAC10 Muted
DAC9 Soft Mute
DAC9 Normal Operation
DAC9 Muted
Rev. A | Page 34 of 52
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
Data Sheet
ADAU1966A
MASTER VOLUME CONTROL REGISTER
Address: 0x0B, Reset: 0x00, Name: DACMSTR_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 36. Bit Descriptions for DACMSTR_VOL
Bits
[7:0]
Bit Name
DACMSTR_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
Master Volume Control
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 1 VOLUME CONTROL REGISTER
Address: 0x0C, Reset: 0x00, Name: DAC01_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 37. Bit Descriptions for DAC01_VOL
Bits
[7:0]
Bit Name
DAC01_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 1
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 35 of 52
ADAU1966A
Data Sheet
DAC 2 VOLUME CONTROL REGISTER
Address: 0x0D, Reset: 0x00, Name: DAC02_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 38. Bit Descriptions for DAC02_VOL
Bits
[7:0]
Bit Name
DAC02_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 2
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 3 VOLUME CONTROL REGISTER
Address: 0x0E, Reset: 0x00, Name: DAC03_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 39. Bit Descriptions for DAC03_VOL
Bits
[7:0]
Bit Name
DAC03_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 3
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 36 of 52
Data Sheet
ADAU1966A
DAC 4 VOLUME CONTROL REGISTER
Address: 0x0F, Reset: 0x00, Name: DAC04_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 40. Bit Descriptions for DAC04_VOL
Bits
[7:0]
Bit Name
DAC04_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 4
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 5 VOLUME CONTROL REGISTER
Address: 0x10, Reset: 0x00, Name: DAC05_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 41. Bit Descriptions for DAC05_VOL
Bits
[7:0]
Bit Name
DAC05_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 5
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 37 of 52
ADAU1966A
Data Sheet
DAC 6 VOLUME CONTROL REGISTER
Address: 0x11, Reset: 0x00, Name: DAC06_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 42. Bit Descriptions for DAC06_VOL
Bits
[7:0]
Bit Name
DAC06_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 6
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 7 VOLUME CONTROL REGISTER
Address: 0x12, Reset: 0x00, Name: DAC07_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 43. Bit Descriptions for DAC07_VOL
Bits
[7:0]
Bit Name
DAC07_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 7
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 38 of 52
Data Sheet
ADAU1966A
DAC 8 VOLUME CONTROL REGISTER
Address: 0x13, Reset: 0x00, Name: DAC08_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 44. Bit Descriptions for DAC08_VOL
Bits
[7:0]
Bit Name
DAC08_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 8
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 9 VOLUME CONTROL REGISTER
Address: 0x14, Reset: 0x00, Name: DAC09_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 45. Bit Descriptions for DAC09_VOL
Bits
[7:0]
Bit Name
DAC09_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 9
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 39 of 52
ADAU1966A
Data Sheet
DAC 10 VOLUME CONTROL REGISTER
Address: 0x15, Reset: 0x00, Name: DAC10_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 46. Bit Descriptions for DAC10_VOL
Bits
[7:0]
Bit Name
DAC10_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 10
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 11 VOLUME CONTROL REGISTER
Address: 0x16, Reset: 0x00, Name: DAC11_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 47. Bit Descriptions for DAC11_VOL
Bits
[7:0]
Bit Name
DAC11_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 11
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 40 of 52
Data Sheet
ADAU1966A
DAC 12 VOLUME CONTROL REGISTER
Address: 0x17, Reset: 0x00, Name: DAC12_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 48. Bit Descriptions for DAC12_VOL
Bits
[7:0]
Bit Name
DAC12_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 12
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 13 VOLUME CONTROL REGISTER
Address: 0x18, Reset: 0x00, Name: DAC13_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 49. Bit Descriptions for DAC13_VOL
Bits
[7:0]
Bit Name
DAC13_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 13
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 41 of 52
ADAU1966A
Data Sheet
DAC 14 VOLUME CONTROL REGISTER
Address: 0x19, Reset: 0x00, Name: DAC14_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 50. Bit Descriptions for DAC14_VOL
Bits
[7:0]
Bit Name
DAC14_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 14
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x00
Access
RW
DAC 15 VOLUME CONTROL REGISTER
Address: 0x1A, Reset: 0x00, Name: DAC15_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 51. Bit Descriptions for DAC15_VOL
Bits
[7:0]
Bit Name
DAC15_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 15
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Rev. A | Page 42 of 52
Data Sheet
ADAU1966A
DAC 16 VOLUME CONTROL REGISTER
Address: 0x1B, Reset: 0x00, Name: DAC16_VOL
Each 1-bit step corresponds to a 0.375 dB change in volume. See Table 58 for a complete list of the volume settings.
Table 52. Bit Descriptions for DAC16_VOL
Bits
[7:0]
Bit Name
DAC16_VOL
Settings
00000000
00000001
00000010
11111110
11111111
Description
DAC Volume Control Channel 16
0 dB (default)
−0.375 dB
−0.750 dB
−95.250 dB
−95.625 dB
Reset
0x00
Access
RW
Reset
0x0
Access
RW
PAD STRENGTH REGISTER
Address: 0x1C, Reset: 0x00, Name: PAD_STRGTH
Table 53. Bit Descriptions for PAD_STRGTH
Bits
5
Bit Name
PAD_DRV
Settings
0
1
Description
Output Pad Drive Strength Control
4 mA Drive for All Pads
8 mA Drive for All Pads
Rev. A | Page 43 of 52
ADAU1966A
Data Sheet
DAC POWER ADJUST 1 REGISTER
Address: 0x1D, Reset: 0xAA, Name: DAC_POWER1
Table 54. Bit Descriptions for DAC_POWER1
Bits
[7:6]
Bit Name
DAC04_POWER
Settings
00
01
10
11
[5:4]
DAC03_POWER
00
01
10
11
[3:2]
DAC02_POWER
00
01
10
11
[1:0]
DAC01_POWER
00
01
10
11
Description
DAC Power Control Channel 4
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 3
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 2
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 1
Low Power
Lowest Power
Best Performance
Good Performance
Rev. A | Page 44 of 52
Reset
0x2
Access
RW
0x2
RW
0x2
RW
0x2
RW
Data Sheet
ADAU1966A
DAC POWER ADJUST 2 REGISTER
Address: 0x1E, Reset: 0xAA, Name: DAC_POWER2
Table 55. Bit Descriptions for DAC_POWER2
Bits
[7:6]
Bit Name
DAC08_POWER
Settings
00
01
10
11
[5:4]
DAC07_POWER
00
01
10
11
[3:2]
DAC06_POWER
00
01
10
11
[1:0]
DAC05_POWER
00
01
10
11
Description
DAC Power Control Channel 8
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 7
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 6
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 5
Low Power
Lowest Power
Best Performance
Good Performance
Rev. A | Page 45 of 52
Reset
0x2
Access
RW
0x2
RW
0x2
RW
0x2
RW
ADAU1966A
Data Sheet
DAC POWER ADJUST 3 REGISTER
Address: 0x1F, Reset: 0xAA, Name: DAC_POWER3
Table 56. Bit Descriptions for DAC_POWER3
Bits
[7:6]
Bit Name
DAC12_POWER
Settings
00
01
10
11
[5:4]
DAC11_POWER
00
01
10
11
[3:2]
DAC10_POWER
00
01
10
11
[1:0]
DAC09_POWER
00
01
10
11
Description
DAC Power Control Channel 12
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 11
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 10
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 9
Low Power
Lowest Power
Best Performance
Good Performance
Rev. A | Page 46 of 52
Reset
0x2
Access
RW
0x2
RW
0x2
RW
0x2
RW
Data Sheet
ADAU1966A
DAC POWER ADJUST 4 REGISTER
Address: 0x20, Reset: 0xAA, Name: DAC_POWER4
Table 57. Bit Descriptions for DAC_POWER4
Bits
[7:6]
Bit Name
DAC16_POWER
Settings
00
01
10
11
[5:4]
DAC15_POWER
00
01
10
11
[3:2]
DAC14_POWER
00
01
10
11
[1:0]
DAC13_POWER
00
01
10
11
Description
DAC Power Control Channel 16
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 15
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 14
Low Power
Lowest Power
Best Performance
Good Performance
DAC Power Control Channel 13
Low Power
Lowest Power
Best Performance
Good Performance
Rev. A | Page 47 of 52
Reset
0x2
Access
RW
0x2
RW
0x2
RW
0x2
RW
ADAU1966A
Data Sheet
Table 58. Volume Settings
Binary Value
00000000
00000001
00000010
00000011
00000100
00000101
00000110
00000111
00001000
00001001
00001010
00001011
00001100
00001101
00001110
00001111
00010000
00010001
00010010
00010011
00010100
00010101
00010110
00010111
00011000
00011001
00011010
00011011
00011100
00011101
00011110
00011111
00100000
00100001
00100010
00100011
00100100
00100101
00100110
00100111
00101000
00101001
00101010
00101011
00101100
00101101
00101110
00101111
Hex Value
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
Volume Attenuation (dB)
0
−0.375
−0.75
−1.125
−1.5
−1.875
−2.25
−2.625
−3
−3.375
−3.75
−4.125
−4.5
−4.875
−5.25
−5.625
−6
−6.375
−6.75
−7.125
−7.5
−7.875
−8.25
−8.625
−9
−9.375
−9.75
−10.125
−10.5
−10.875
−11.25
−11.625
−12
−12.375
−12.75
−13.125
−13.5
−13.875
−14.25
−14.625
−15
−15.375
−15.75
−16.125
−16.5
−16.875
−17.25
−17.625
Binary Value
00110000
00110001
00110010
00110011
00110100
00110101
00110110
00110111
00111000
00111001
00111010
00111011
00111100
00111101
00111110
00111111
01000000
01000001
01000010
01000011
01000100
01000101
01000110
01000111
01001000
01001001
01001010
01001011
01001100
01001101
01001110
01001111
01010000
01010001
01010010
01010011
01010100
01010101
01010110
01010111
01011000
01011001
01011010
01011011
01011100
01011101
01011110
01011111
Rev. A | Page 48 of 52
Hex Value
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
Volume Attenuation (dB)
−18
−18.375
−18.75
−19.125
−19.5
−19.875
−20.25
−20.625
−21
−21.375
−21.75
−22.125
−22.5
−22.875
−23.25
−23.625
−24
−24.375
−24.75
−25.125
−25.5
−25.875
−26.25
−26.625
−27
−27.375
−27.75
−28.125
−28.5
−28.875
−29.25
−29.625
−30
−30.375
−30.75
−31.125
−31.5
−31.875
−32.25
−32.625
−33
−33.375
−33.75
−34.125
−34.5
−34.875
−35.25
−35.625
Data Sheet
Binary Value
01100000
01100001
01100010
01100011
01100100
01100101
01100110
01100111
01101000
01101001
01101010
01101011
01101100
01101101
01101110
01101111
01110000
01110001
01110010
01110011
01110100
01110101
01110110
01110111
01111000
01111001
01111010
01111011
01111100
01111101
01111110
01111111
10000000
10000001
10000010
10000011
10000100
10000101
10000110
10000111
10001000
10001001
10001010
10001011
10001100
10001101
10001110
10001111
Hex Value
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
ADAU1966A
Volume Attenuation (dB)
−36
−36.375
−36.75
−37.125
−37.5
−37.875
−38.25
−38.625
−39
−39.375
−39.75
−40.125
−40.5
−40.875
−41.25
−41.625
−42
−42.375
−42.75
−43.125
−43.5
−43.875
−44.25
−44.625
−45
−45.375
−45.75
−46.125
−46.5
−46.875
−47.25
−47.625
−48
−48.375
−48.75
−49.125
−49.5
−49.875
−50.25
−50.625
−51
−51.375
−51.75
−52.125
−52.5
−52.875
−53.25
−53.625
Binary Value
10010000
10010001
10010010
10010011
10010100
10010101
10010110
10010111
10011000
10011001
10011010
10011011
10011100
10011101
10011110
10011111
10100000
10100001
10100010
10100011
10100100
10100101
10100110
10100111
10101000
10101001
10101010
10101011
10101100
10101101
10101110
10101111
10110000
10110001
10110010
10110011
10110100
10110101
10110110
10110111
10111000
10111001
10111010
10111011
10111100
10111101
10111110
10111111
Rev. A | Page 49 of 52
Hex Value
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
Volume Attenuation (dB)
−54
−54.375
−54.75
−55.125
−55.5
−55.875
−56.25
−56.625
−57
−57.375
−57.75
−58.125
−58.5
−58.875
−59.25
−59.625
−60
−60.375
−60.75
−61.125
−61.5
−61.875
−62.25
−62.625
−63
−63.375
−63.75
−64.125
−64.5
−64.875
−65.25
−65.625
−66
−66.375
−66.75
−67.125
−67.5
−67.875
−68.25
−68.625
−69
−69.375
−69.75
−70.125
−70.5
−70.875
−71.25
−71.625
ADAU1966A
Binary Value
11000000
11000001
11000010
11000011
11000100
11000101
11000110
11000111
11001000
11001001
11001010
11001011
11001100
11001101
11001110
11001111
11010000
11010001
11010010
11010011
11010100
11010101
11010110
11010111
11011000
11011001
11011010
11011011
11011100
11011101
11011110
11011111
Hex Value
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
Data Sheet
Volume Attenuation (dB)
−72
−72.375
−72.75
−73.125
−73.5
−73.875
−74.25
−74.625
−75
−75.375
−75.75
−76.125
−76.5
−76.875
−77.25
−77.625
−78
−78.375
−78.75
−79.125
−79.5
−79.875
−80.25
−80.625
−81
−81.375
−81.75
−82.125
−82.5
−82.875
−83.25
−83.625
Binary Value
11100000
11100001
11100010
11100011
11100100
11100101
11100110
11100111
11101000
11101001
11101010
11101011
11101100
11101101
11101110
11101111
11110000
11110001
11110010
11110011
11110100
11110101
11110110
11110111
11111000
11111001
11111010
11111011
11111100
11111101
11111110
11111111
Rev. A | Page 50 of 52
Hex Value
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Volume Attenuation (dB)
−84
−84.375
−84.75
−85.125
−85.5
−85.875
−86.25
−86.625
−87
−87.375
−87.75
−88.125
−88.5
−88.875
−89.25
−89.625
−90
−90.375
−90.75
−91.125
−91.5
−91.875
−92.25
−92.625
−93
−93.375
−93.75
−94.125
−94.5
−94.875
−95.25
−95.625
Data Sheet
ADAU1966A
OUTLINE DIMENSIONS
0.75
0.60
0.45
16.20
16.00 SQ
15.80
1.60
MAX
61
80
60
1
PIN 1
14.20
14.00 SQ
13.80
TOP VIEW
(PINS DOWN)
0.15
0.05
SEATING
PLANE
0.20
0.09
7°
3.5°
0°
0.10
COPLANARITY
VIEW A
ROTATED 90° CCW
20
41
40
21
VIEW A
0.65
BSC
LEAD PITCH
0.38
0.32
0.22
COMPLIANT TO JEDEC STANDARDS MS-026-BEC
051706-A
1.45
1.40
1.35
Figure 24. 80-Lead Low Profile Quad Flat Package [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2
ADAU1966AWBSTZ
ADAU1966AWBSTZ-RL
EVAL-ADAU1966AZ
1
2
Temperature Range
−40°C to +105°C
−40°C to +105°C
Package Description
80-Lead LQFP
80-Lead LQFP, 13” Tape and Reel
Evaluation Board
Package Option
ST-80-2
ST-80-2
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADAU1966AW models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
Rev. A | Page 51 of 52
ADAU1966A
Data Sheet
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2013–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D11298-0-3/16(A)
Rev. A | Page 52 of 52