WRB-YQD-30W

WRB-YQD-30W Series
W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTER
30
30W,
SELECTION GUIDE
FEATURES
Wide 2:1 DC input range
◆
In/out capacitance1000pF
◆
Protections : Short circuit / Overload / Over voltage
◆
1500VDC I/O isolation for D/D
◆
Cooling by free air convection
◆
Built-in remote ON-OFF control
◆
100% full load burn-in test
◆
Order code
Input voltage range
(VDC)
Output voltage(VDC)
Output current
max.(mA)
Efficiency typ.(%)
WRB1203YQD-5000
9~18
3.3
5000
77
WRB1205YQD-5000
9~18
5
5000
77
WRB1212YQD-2100
9~18
12
2100
80
WRB1215YQD-1700
9~18
15
1700
80
WRB1224YQD-30W
9~18
24
1250
78
WRB2403YQD-5000
18~36
3.3
5000
79
WRB2405YQD-5000
18~36
5
5000
79
WRB2412YQD-30W
18~36
12
2500
82
WRB2415YQD-30W
18~36
15
2000
83
WRB2424YQD-30W
18~36
24
1250
78
WRB4803YQD-5000
36~72
3.3
5000
80
WRB4805YQD-5000
36~72
5
5000
80
WRB4812YQD-30W
36~72
12
2500
84
WRB4815YQD-30W
36~72
15
2000
85
WRB4824YQD-30W
36~72
24
1250
78
Fixed switching frequency at 225KHz
◆
Lost cost
◆
SPECIFICATION
MTBF>1000Khours
◆
High reliability
◆
INPUT
2 year warranty
◆
DC CURRENT
WRB12XX:3.6A
IDLE CURRENT
WRB12XX:35mA WRB24XX/WRB48XX:30mA
WRB24XX:2A
WRB48XX:1A
Above 105% rated output power
OVERLOAD
MODEL SELECTION
①
②
③
④
⑤
⑥
WRB 24 12 Y QD -30W
0W(2500)
(2500)
OVER VOLTAGE
①Product Series ②Input Voltage
③Output Voltage ④Wide (2:1) Input Range
⑤2"×2"DIP Package Style
⑥Rated Power(Output current)
The WRB-YQD-30W Series series of
DC/DC converters has been designed for a wide
range of applications including communications,
industrial systems and battery powered mobile
equipments. Key features are high power
density and ultrawide input ranges of 9~36 VDC
and 18~75 VDC. Other features of this converter
are internal filtering according to EN 55022,
level A, safety approval to EN 60950 and UL
1950, wide operating temperature range and
remote on/off (opt.).
SHORT CIRCUIT
SAFETY &EMC
(Note 6)
OTHERS
MICRODC RESERVES THE COPYRIGHT
NOTE
http://www.microdc.cn
WRBXX03:3.8~4.95V
WRBXX05:5.75 ~ 7.5V
WRBXX12:13.8 ~ 18V
WRBXX15:17.25 ~ 22.5V
Protection type : Shut off o/p voltage, clamping by zener diode
FUNCTION
APPLICATIONS
Protection type : Over power limiting, recovers automatically after fault
condition is removed
Protection type : Constant current limiting, recovers automatically after
fault condition is removed
ON/OFF CONTROL
Logic "1" or open: power on
Logic "0" short to Vin-: power off
WORKING TEMP.
-25 ~ +85℃ (Refer to output load derating curve)
STORAGE TEMP.,
HUMIDITY
-25 ~ +85℃, 0 ~ 95% RH
TEMP.
COEFFICIENT
SAFETY
STANDARDS
ISOLATION
VOLTAGE
ISOLATION
RESISTANCE
EMI CONDUCTION
& RADIATION
±0.03%/ ℃(0~50℃)
Design refer to LVD
I/P-O/P:1.5KVDC
I/P-O/P:100M Ohms/500VDC
Compliance to EN55022 (CISPR22) Class B
EMS IMMUNITY
Compliance to EN61000-2,3,4,6,8; ENV50204, EN55024,
light industry level,criteria A
MTBF
322.4K hrs min.
DIMENSION
50.8×50.8×16mm (2"×2"×0.63") (L×W×H)
PACKING
0.1Kg; 150pcs/15.8Kg/0.97CUFT
MIL-HDBK-217F (25℃)
1. All parameters NOT specially mentioned are measured at 12,24,48VDC input,
rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted
pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Short circuit not more than 60 second.
5. DC source wires 5cm, an input external al capacitor 47 ~ 100uF is required.
6. The power supply is considered a component which will be installed into a final
equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 3
WRB-YQD-30W Series
Mechanical Specification
Pin
Assignment
Pin
Assignment
1
+Vin
6
+Vout
2
-Vin
7
-Vout
3,5
No pin
8
Trim
4
Ctrl (ON/OFF)
TYPICAL CHARACTERISTICS
Temperature Derating Graph
Unit:mm
AMBIENT TEMPERATURE (℃)
APPLICATION NOTE
Requirement on output load
In order to ensure the product operate efficiently and reliably,in addition to a
max load(namely full load), a minimum load is specified for this kind of DC/DC
converter.Make sure the specified range of input voltage is not exceeded,the
minimum output load no less than 10% load.If the actual load is less than the
specified minimum load, the output ripple may increase sharply while its
efficiency and reliability will reduce greatly.If the actual output power is very
small,please add an appropriate resistor as extra loading,or contact our
company for other lower output power products.
External Output Trimming
OUTPUTMAYOPTIONALLYBE EXTERNALLYTRIMMED(10%)
A FIXED RESISTER ORAN EXTERNALTRIMPOTAS SHOWN
Recommended Circuit
All the WRB_YQD-30W Series have been tested according to the following
recommended testing circuit before leaving factory.This series should be
tested under load(see Figure 1).
If you want to further decrease the input/output ripple,you can increase
capacitance properly or choose capacitors with low ESR.However,the
capacitance of the output filter capacitor must be proper.If the capacitance is
too big,a startup problem might arise.For every channel of output,provided the
safe and reliable operation is ensured,the greatest capacitance of its filter
capacitor sees (Table 1).General:
Cin: 10μF-47μF
Cout: 10μF/100mA
CONTROL INPUT.....................................PIN4
CTRL Terminal
CONTROL COMMON................................PIN2
When open or high impedance,the converter work well; When this pin is ‘high’;
the converter shutdown; It should be note that the input current (Ic) should
between 5-10mA, exceeding the maximum 20mA will cause permanence
damage to the converter.
The value of R Can be derived as follows :
ON/OFF Control Pin
LOGIC COMPATIBILITY......CMOS OR OPEN COLLECTOR TTL
CONTROL VOLTAGE
ON..........................................+5.5VDC min OR OPEN CIRCUIT
OFF......................................+2.5VDC max. OR SHORT TO PIN2
Input current
While using unstable power source,please ensure the output voltage and ripple
voltage do not exceed indexes of the converter.The preceding power source
must be able to provide for converter sufficient starting current Ip(Figure 2).
General:Ip≤1.6*Iin-max
No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
WRB-YQD-30W Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
FOSC:225KHz
RECOMMENDED FOOTPRINT
TUBE OUTLINE DIMENSIONS
Unit :mm[inch]
General tolerances:±0.50mm[±0.020inch]
L=230mm[9.055inch] Tube Quantity: 7pcs
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:[email protected]
Website:http://www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3