MICRODC WRB-YQD-30W

WRB-YQD-30W Series
W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC
30
30W,
DC--DC CONVERTER
SELECTION GUIDE
FEATURES
◆Wide 2:1 DC input range
◆In/out capacitance1000pF
◆Protections : Short circuit / Overload /
Over voltage
◆1000VDC I/O isolation for D/D
◆Cooling by free air convection
Order code
Input voltage
range
Output voltage
Output
current max.
Efficiency typ.
WRB1203YQD-5000
9.2 ~ 18 VDC
3.3VDC
5000mA
77
WRB1205YQD-5000
9.2 ~ 18 VDC
5VDC
5000mA
77
WRB1212YQD-2100
9.2 ~ 18 VDC
12VDC
2100mA
80
WRB1215YQD-1700
9.2 ~ 18 VDC
15VDC
1700mA
80
WRB2403YQD-5000
18~ 36 VDC
3.3VDC
5000mA
79
WRB2405YQD-5000
18~ 36 VDC
5VDC
5000mA
79
WRB2412YQD-30W
18~ 36 VDC
12VDC
2500mA
82
WRB2415YQD-30W
18~ 36 VDC
15VDC
2000mA
83
WRB4803YQD-5000
36~ 72 VDC
3.3VDC
5000mA
80
WRB4805YQD-5000
36~ 72 VDC
5VDC
5000mA
80
WRB4812YQD-30W
36~ 72 VDC
12VDC
2500mA
84
WRB4815YQD-30W
36~ 72 VDC
15VDC
2000mA
85
◆Built-in remote ON-OFF control
◆100% full load burn-in test
SPECIFICATION
◆Fixed switching frequency at 225KHz
INPUT
◆Lost cost
◆MTBF>1000Khours
◆High reliability
◆1 year warranty
PROTECTION
②
③
④
⑤
⑥
①
②
③ ④
⑤
⑥
WRB 12 12 Y QD -30W
FUNCTION
①Product Series
②Input Voltage
③Output Voltage
④Wide (2:1) Input Range
⑤DIP Package Style ⑥Rated Power
ENVIRONMENT
APPLICATIONS
The
WRB-YQD-30W
Series
series
of
12S:3.6A 24S:2A 48S:1A
IDLE CURRENT
12S:35mA 24S/48S:30mA
OVERLOAD
Above 105% rated output power
Protection type : Over power limiting, recovers automatically
after fault condition is removed
OVER VOLTAGE
WRBXX03:3.8 ~
WRBXX05:5.75 ~ 7.5V
WRBXX12:13.8 ~ 18V
WRBXX15:17.25 ~ 22.5V
Protection type : Shut off o/p voltage, clamping by zener
MODEL SELECTION
①
DC CURRENT
DC/DC
converters has been designed for a wide range of
applications including communications, industrial systems
SAFETY &EMC
(Note 6)
and battery powered mobile equipments. Key features are
high power density (12W in a 2“x1“x 0.4“ package) and
ultrawide input ranges of 9 – 36 VDC and 18 –75 VDC.
Other features of this converter are internal filtering
OTHERS
according to EN 55022, level A, safety approval to EN
60950 and UL 1950, wide operating temperature range
and remote on/off (opt.).
NOTE
SHORT CIRCUIT
Protection type : Constant current limiting, recovers
automatically after fault condition is removed
ON/OFF CONTROL
Logic "1" or open: power on
power off
WORKING TEMP.
-25 ~ +85℃ (Refer to output load derating curve)
STORAGE TEMP.,
HUMIDITY
-25 ~ +85℃, 0 ~ 95% RH
TEMP.
COEFFICIENT
SAFETY
STANDARDS
ISOLATION
VOLTAGE
ISOLATION
RESISTANCE
EMI CONDUCTION
& RADIATION
Logic "0" short to Vin-:
±0.03%/ ℃(0~50℃)
Design refer to LVD
I/P-O/P:1KVDC
I/P-O/P:100M Ohms/500VDC
Compliance to EN55022 (CISPR22) Class B
EMS IMMUNITY
Compliance to EN61000-2,3,4,6,8; ENV50204, EN55024,
light industry level,criteria A
MTBF
322.4K hrs min.
DIMENSION
50.8*50.8*16mm (2"*2"*0.63") (L*W*H)
PACKING
0.1Kg; 150pcs/15.8Kg/0.97CUFT
MIL-HDBK-217F (25℃)
1. All parameters NOT specially mentioned are measured at 12,24,48VDC input,
rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted
pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Short circuit not more than 60 second.
5. DC source wires 5cm, an input external al capacitor 47 ~ 100uF is required.
6. The power supply is considered a component which will be installed into a final
equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
MICRODC reserves the copyright
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
page 1/3
WRB-YQD-30W Series
Mechanical Specification
TYPICAL CHARACTERISTICS
Temperature Derating Graph
RECOMMENDED CIRCUIT
Output Graph
APPLICATION NOTE
External Output Trimming
Requirement on output load
In order to ensure the product operate efficiently and reliably,in addition to a
max load(namely full load), a minimum load is specified for this kind of
DC/DC converter.Make sure the specified range of input voltage is not
exceeded,the minimum output load no less than 10% load.If the actual load
is less than the specified minimum load, the output ripple may increase
sharply while its efficiency and reliability will reduce greatly.If the actual
output power is very small,please add an appropriate resistor as extra
loading,or contact our company for other lower output power products.
Recommended Circuit
All the WRB_YQD-30W Series have been tested according to the following
recommended testing circuit before leaving factory.This series should be
tested under load(see Figure 1).
If you want to further decrease the input/output ripple,you can increase
capacitance properly or choose capacitors with low ESR.However,the
capacitance of the output filter capacitor must be proper.If the capacitance
is too big,a startup problem might arise.For every channel of output,provided
the safe and reliable operation is ensured,the greatest capacitance of its
filter capacitor sees (Table 1).General:
Cin: 10μF-47μF
Cout: 10μF/100mA
ON/OFF Control Pin
CONTROL INPUT.....................................PIN4
CONTROL COMMON................................PIN2
LOGIC COMPATIBILITY......CMOS OR OPEN
COLLECTOR TTL
CONTROL VOLTAGE
ON............+5.5VDC min OR OPEN CIRCUIT
OFF......+2.5VDC max. OR SHORT TO PIN2
CTRL Terminal
When open or high impedance,the converter work well; When this pin is
‘high’; the converter shutdown; It should be note that the input current (Ic)
should between 5-10mA, exceeding the maximum 20mA will cause
permanence damage to the converter.
The value of R Can be derived as follows :
Input current
While using unstable power source,please ensure the output voltage and
ripple voltage do not exceed indexes of the converter.The preceding power
source must be able to provide for converter sufficient starting current
Ip(Figure 2).
General:Ip≤1.6*Iin-max
No parallel connection or plug and play
http://www.microdc.cn
Pin No. Assignment
No.
Assignme
nt
No.
Assignmen
t
1
+Vin
6
+Vout
2
-Vin
7
-Vout
3,5
No pin
8
Trim
4
Control ON/OFF
Pin
Pin
Technical enquiries-Email:[email protected] Tel:0086-20-86000646
page 2/3
WRB-YQD-30W Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
RECOMMENDED FOOTPRINT
TUBE OUTLINE DIMENSIONS
Unit :mm[inch]
General tolerances:±0.50mm[±0.020inch]
L=230mm[9.055inch] Tube Quantity: 7pcs
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
REACH COMPLIANT INFORMATION
E-mail:[email protected]
Website:http://www.microdc.cn
http://www.microdc.cn
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
page 3/3