TLE7250VLE Data Sheet (2 MB, EN)

TLE7250V
High Speed CAN-Transceiver
TLE7250VLE
TLE7250VSJ
Data Sheet
Rev. 1.0, 2015-08-12
Automotive Power
TLE7250VLE
TLE7250VSJ
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
3.1
3.2
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
4.1
4.2
4.2.1
4.2.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
High Speed CAN Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Normal-operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power-save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power-up and Undervoltage Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power-down State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Forced Power-save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Undervoltage on the Digital Supply VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Undervoltage on the Transmitter Supply VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Voltage Adaption to the Microcontroller Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5
5.1
5.2
5.3
5.4
5.5
Fail Safe Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unconnected Logic Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TxD Time-out Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overtemperature Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delay Time for Mode Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
15
15
16
16
6
6.1
6.2
6.3
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
18
7
7.1
7.2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Functional Device Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
8.1
8.2
8.3
8.3.1
8.3.2
8.4
Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESD Robustness according to IEC61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Examples for Mode Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Change while the TxD Signal is “low” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode Change while the Bus Signal is “dominant” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Data Sheet
2
26
26
27
28
29
30
31
Rev. 1.0, 2015-08-12
High Speed CAN-Transceiver
1
TLE7250VLE
TLE7250VSJ
Overview
Features
•
Fully compatible to ISO 11898-2
•
Wide common mode range for electromagnetic immunity (EMI)
•
Very low electromagnetic emission (EME)
•
Excellent ESD robustness
•
Guaranteed loop delay symmetry to support CAN FD data frames up
to 2 MBit/s
•
•
VIO input for voltage adaption to the microcontroller supply
Extended supply range on VCC and VIO supply
CAN short circuit proof to ground, battery and VCC
•
TxD time-out function
•
Low CAN bus leakage current in power-down state
•
Overtemperature protection
•
Protected against automotive transients
•
Power-save mode
•
Transmitter supply VCC can be turned off in power-save mode
•
Green Product (RoHS compliant)
•
Two package variants: PG-TSON-8 and PG-DSO-8
•
AEC Qualified
•
PG-TSON-8
PG-DSO-8
Description
The TLE7250V is a transceiver designed for HS CAN networks in automotive and industrial applications. As an
interface between the physical bus layer and the CAN protocol controller, the TLE7250V drives the signals to the
bus and protects the microcontroller against interferences generated within the network. Based on the high
symmetry of the CANH and CANL signals, the TLE7250V provides a very low level of electromagnetic emission
(EME) within a wide frequency range.
The TLE7250V is available in a small, leadless PG-TSON-8 package and in a PG-DSO-8 package. Both packages
are RoHS compliant and halogen free. Additionally the PG-TSON-8 package supports the solder joint
requirements for automated optical inspection (AOI). The TLE7250VLE and the TLE7250VSJ are fulfilling or
exceeding the requirements of the ISO11898-2.
The TLE7250V provides a digital supply input VIO and a power-save mode. It is designed to fulfill the enhanced
physical layer requirements for CAN FD and supports data rates up to 2 MBit/s.
On the basis of a very low leakage current on the HS CAN bus interface the TLE7250V provides an excellent
passive behavior in power-down state. These and other features make the TLE7250V exceptionally suitable for
Type
Package
Marking
TLE7250VLE
PG-TSON-8
7250V
TLE7250VSJ
PG-DSO-8
7250V
Data Sheet
3
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Overview
mixed supply HS CAN networks.
Based on the Infineon Smart Power Technology SPT, the TLE7250V provides excellent ESD immunity together
with a very high electromagnetic immunity (EMI). The TLE7250V and the Infineon SPT technology are AEC
qualified and tailored to withstand the harsh conditions of the automotive environment.
Two different operating modes, additional fail-safe features like a TxD time-out and the optimized output slew rates
on the CANH and CANL signals, make the TLE7250V the ideal choice for large HS CAN networks with high data
transmission rates.
Data Sheet
4
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Block Diagram
2
Block Diagram
3
5
VCC
VIO
Transmitter
CANH
CANL
1
7
Driver
Tempprotection
6
TxD
Timeout
Mode
control
8
NEN
Receiver
Normal-mode receiver
4
RxD
VCC/2 =
Bus-biasing
GND 2
Figure 1
Data Sheet
Functional block diagram
5
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Pin Configuration
3
Pin Configuration
3.1
Pin Assignment
TxD
1
GND
2
8
NEN
7
CANH
CANL
TxD
1
8
NEN
GND
2
7
CANH
VCC
3
6
CANL
RxD
4
5
PAD
VCC
3
6
RxD
4
5
VIO
(Top-side x-ray view)
Figure 2
Pin configuration
3.2
Pin Definitions
Table 1
Pin definitions and functions
Pin No.
Symbol
Function
1
TxD
Transmit Data Input;
internal pull-up to VIO, “low” for “dominant” state.
2
GND
Ground
3
VCC
Transmitter Supply Voltage;
100 nF decoupling capacitor to GND required,
VCC can be turned off in power-save mode.
4
RxD
Receive Data Output;
“low” in “dominant” state.
5
VIO
Digital Supply Voltage;
supply voltage input to adapt the logical input and output voltage levels of the
transceiver to the microcontroller supply,
100 nF decoupling capacitor to GND required.
6
CANL
CAN Bus Low Level I/O;
“low” in “dominant” state.
7
CANH
CAN Bus High Level I/O;
“high” in “dominant” state.
Data Sheet
6
VIO
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Pin Configuration
Table 1
Pin definitions and functions (cont’d)
Pin No.
Symbol
Function
8
NEN
Not Enable Input;
internal pull-up to VIO, “low” for normal-operating mode.
PAD
–
Connect to PCB heat sink area.
Do not connect to other potential than GND.
Data Sheet
7
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
4
Functional Description
HS CAN is a serial bus system that connects microcontrollers, sensors and actuators for real-time control
applications. The use of the Controller Area Network (abbreviated CAN) within road vehicles is described by the
international standard ISO 11898. According to the 7-layer OSI reference model the physical layer of a HS CAN
bus system specifies the data transmission from one CAN node to all other available CAN nodes within the
network. The physical layer specification of a CAN bus system includes all electrical and mechanical specifications
of a CAN network. The CAN transceiver is part of the physical layer specification. Several different physical layer
standards of CAN networks have been developed in recent years. The TLE7250V is a High Speed CAN
transceiver without a wake-up function and defined by the international standard ISO 11898-2.
4.1
High Speed CAN Physical Layer
VIO =
VCC =
TxD =
TxD
VIO
RxD =
CANH =
t
CANH
CANL
CANL =
VDiff =
VCC
Digital supply voltage
Transmitter supply voltage
Transmit data input from
the microcontroller
Receive data output to
the microcontroller
Bus level on the CANH
input/output
Bus level on the CANL
input/output
Differential voltage
between CANH and CANL
VDiff = VCANH – VCANL
t
VDiff
VCC
“dominant” receiver threshold
“recessive” receiver threshold
t
RxD
VIO
tLoop(H,L)
Figure 3
Data Sheet
tLoop(L,H)
t
High speed CAN bus signals and logic signals
8
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
The TLE7250V is a High-Speed CAN transceiver, operating as an interface between the CAN controller and the
physical bus medium. A HS CAN network is a two wire, differential network which allows data transmission rates
for CAN FD frames up to 2 MBit/s. Characteristic for HS CAN networks are the two signal states on the HS CAN
bus: “dominant” and “recessive” (see Figure 3).
VCC, VIO and GND are the supply pins for the TLE7250V. The pins CANH and CANL are the interface to the
HS CAN bus and operate in both directions, as an input and as an output. RxD and TxD pins are the interface to
the CAN controller, the TxD pin is an input pin and the RxD pin is an output pin. The NEN pin is the input pin for
the mode selection (see Figure 4).
By setting the TxD input pin to logical “low” the transmitter of the TLE7250V drives a “dominant” signal to the CANH
and CANL pins. Setting TxD input to logical “high” turns off the transmitter and the output voltage on CANH and
CANL discharges towards the “recessive” level. The “recessive” output voltage is provided by the bus biasing (see
Figure 1). The output of the transmitter is considered to be “dominant”, when the voltage difference between
CANH and CANL is at least higher than 1.5 V (VDiff = VCANH - VCANL).
Parallel to the transmitter the normal-mode receiver monitors the signal on the CANH and CANL pins and indicates
it on the RxD output pin. A “dominant” signal on the CANH and CANL pins sets the RxD output pin to logical “low”,
vice versa a “recessive” signal sets the RxD output to logical “high”. The normal-mode receiver considers a voltage
difference (VDiff) between CANH and CANL above 0.9 V as “dominant” and below 0.5 V as “recessive”.
To be conform with HS CAN features, like the bit to bit arbitration, the signal on the RxD output has to follow the
signal on the TxD input within a defined loop delay tLoop ≤ 255 ns.
The thresholds of the digital inputs (TxD and NEN) and also the RxD output voltage are adapted to the digital
power supply VIO.
Data Sheet
9
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
4.2
Modes of Operation
The TLE7250V supports two different modes of operation, power-save mode and normal-operating mode while
the transceiver is supplied according to the specified functional range. The mode of operation is selected by the
NEN input pin (see Figure 4).
power-save mode
VCC = “don’t care”
VIO > VIO(UV,R)
NEN = 1
NEN = 0
VCC > VCC(UV,R)
NEN = 1
normal-operating
mode
VIO > VIO(UV,R)
NEN = 0
Figure 4
Mode state diagram
4.2.1
Normal-operating Mode
In normal-operating mode the transmitter and the receiver of the HS CAN transceiver TLE7250V are active (see
Figure 1). The HS CAN transceiver sends the serial data stream on the TxD input pin to the CAN bus. The data
on the CAN bus is displayed at the RxD pin simultaneously. A logical “low” signal on the NEN pin selects the
normal-operating mode, while the transceiver is supplied by VCC and VIO (see Table 2 for details).
4.2.2
Power-save Mode
The power-save mode is an idle mode of the TLE7250V with optimized power consumption. In power-save mode
the transmitter and the normal-mode receiver are turned off. The TLE7250V can not send any data to the CAN
bus nor receive any data from the CAN bus.
The RxD output pin is permanently “high” in the power-save mode.
A logical “high” signal on the NEN pin selects the power-save mode, while the transceiver is supplied by the digital
supply VIO (see Table 2 for details).
In power-save mode the bus input pins are not biased. Therefore the CANH and CANL input pins are floating and
the HS CAN bus interface has a high resistance.
The undervoltage detection on the transmitter supply VCC is turned off, allowing to switch off the VCC supply in
power-save mode.
Data Sheet
10
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
4.3
Power-up and Undervoltage Condition
By detecting an undervoltage event, either on the transmitter supply VCC or the digital supply VIO, the transceiver
TLE7250V changes the mode of operation. Turning off the digital power supply VIO, the transceiver powers down
and remains in the power-down state. While switching off the transmitter supply VCC, the transceiver either
changes to the forced power-save mode, or remains in power-save mode (details see Figure 5).
normal-operating
mode
VIO “on”
VCC “on”
NEN “0”
power-down
state
NEN
VCC
VIO
“X”
“X”
“off”
NEN
VCC
VIO
0
“on”
“on”
VIO “on”
VCC “on”
NEN “0”
VIO “on”
VCC “off”
NEN “0”
VIO “on”
VCC “X”
NEN “1”
power-save
mode
VIO “on”
VCC “X”
NEN “1”
Figure 5
Power-up and undervoltage
Table 2
Modes of operation
NEN
VCC
VIO
1
“X”
“on”
VIO “on”
VCC “on”
NEN “0”
VIO “on”
VCC “off”
NEN “0”
forced power-save
mode
NEN
VCC
VIO
0
“off”
“on”
VIO “on”
VCC “X”
NEN “1”
Mode
NEN
VIO
VCC
Bus Bias
Transmitter
Normal-mode Low-power
Receiver
Receiver
Normal-operating
“low”
“on”
“on”
VCC/2
“on”
“on”
not available
Power-save
“high”
“on”
“X”
floating
“off”
“off”
not available
Forced power-save “low”
“on”
“off”
floating
“off”
“off”
not available
Power-down state
“off”
“X”
floating
“off”
“off”
not available
Data Sheet
“X”
11
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
4.3.1
Power-down State
Independent of the transmitter supply VCC and of the NEN input pin, the TLE7250V is in power-down state when
the digital supply voltage VIO is turned off (see Figure 5).
In the power-down state the input resistors of the receiver are disconnected from the bus biasing VCC/2. The CANH
and CANL bus interface of the TLE7250V is floating and acts as a high-impedance input with a very small leakage
current. The high-ohmic input does not influence the “recessive” level of the CAN network and allows an optimized
EME performance of the entire HS CAN network (see also Table 2).
4.3.2
Forced Power-save Mode
The forced power-save mode is a fail-safe mode to avoid any disturbance on the HS CAN bus, while the
TLE7250V faces a loss of the transmitter supply VCC.
In forced power-save mode, the transmitter and the normal-mode receiver are turned off and therefore the
transceiver TLE7250V can not disturb the bus media.
The RxD output pin is permanently set to logical “high”. The bus biasing is floating (details see Table 2).
The forced power-save mode can only be entered when the transmitter supply VCC is not available, either by
powering up the digital supply VIO only or by turning off the transmitter supply in normal-operating mode. While the
transceiver TLE7250V is in forced power-save mode, switching the NEN input to logical “high” triggers a mode
change to power-save mode (see Figure 5).
4.3.3
Power-up
The HS CAN transceiver TLE7250V powers up if at least the digital supply VIO is connected to the device. By
default the device powers up in power-save mode, due to the internal pull-up resistor on the NEN pin to VIO.
In case the device needs to power-up to normal-operating mode, the NEN pin needs to be pulled active to logical
“low” and the supplies VIO and VCC have to be connected.
By supplying only the digital power supply VIO the TLE7250V powers up either in forced power-save mode or in
power-save mode, depending on the signal of the NEN input pin (see Figure 5).
Data Sheet
12
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
Undervoltage on the Digital Supply VIO
4.3.4
If the voltage on VIO supply input falls below the threshold VIO < VIO(UV,F), the transceiver TLE7250V powers down
and changes to the power-down state.
The undervoltage detection on the digital supply VIO has the highest priority. It is independent of the transmitter
supply VCC and also independent of the currently selected operating mode. An undervoltage event on VIO always
powers down the TLE7250V.
transmitter supply voltage VCC = “don’t care”
VIO
VIO undervoltage monitor
VIO(UV,F)
VIO undervoltage monitor
VIO(UV,R)
hysteresis
VIO(UV,H)
tDelay(UV) delay time undervoltage
t
any mode of operation
power-down state
stand-by mode
NEN
“high” due the internal
pull-up resistor1)
“X” = don’t care
1)
Figure 6
Data Sheet
assuming no external signal applied
t
Undervoltage on the digital supply VIO
13
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Functional Description
4.3.5
Undervoltage on the Transmitter Supply VCC
In case the transmitter supply VCC falls below the threshold VCC < VCC(UV,F), the transceiver TLE7250V changes
the mode of operation to forced power-save mode. The transmitter and also the normal-mode receiver of the
TLE7250V are powered by the VCC supply. In case of an insufficient VCC supply, the TLE7250V can neither
transmit the CANH and CANL signals correctly to the bus, nor can it receive them properly. Therefore the
TLE7250V blocks the transmitter and the receiver in forced power-save mode (see Figure 7).
The undervoltage detection on the transmitter supply VCC is only active in normal-operating mode (see Figure 5).
digital supply voltage VIO = “on”
VCC
VCC undervoltage monitor
VCC(UV,F)
VCC undervoltage monitor
VCC(UV,R)
hysteresis
VCC(UV,H)
tDelay(UV) delay time undervoltage
t
normal-operating mode
forced stand-by mode
normal-operating mode
NEN
Assuming the NEN remains “low”. The “low” signal is driven by the external microcontroller
Figure 7
Undervoltage on the transmitter supply VCC
4.3.6
Voltage Adaption to the Microcontroller Supply
t
The HS CAN transceiver TLE7250V has two different power supplies, VCC and VIO. The power supply VCC supplies
the transmitter and the normal-mode receiver. The power supply VIO supplies the digital input and output buffers
and it is also the main power domain for the internal logic.
To adjust the digital input and output levels of the TLE7250V to the I/O levels of the external microcontroller,
connect the power supply VIO to the microcontroller I/O supply voltage (see Figure 13).
Note: In case the digital supply voltage VIO is not required in the application, connect the digital supply voltage VIO
to the transmitter supply VCC.
Data Sheet
14
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Fail Safe Functions
5
Fail Safe Functions
5.1
Short Circuit Protection
The CANH and CANL bus outputs are short circuit proof, either against GND or a positive supply voltage. A current
limiting circuit protects the transceiver against damages. If the device is heating up due to a continuous short on
the CANH or CANL, the internal overtemperature protection switches off the bus transmitter.
5.2
Unconnected Logic Pins
All logic input pins have an internal pull-up resistor to VIO. In case the VIO supply is activated and the logical pins
are open, the TLE7250V enters into the power-save mode by default. In power-save mode the transmitter of the
TLE7250V is disabled and the bus bias is floating.
5.3
TxD Time-out Function
The TxD time-out feature protects the CAN bus against permanent blocking in case the logical signal on the TxD
pin is continuously “low”. A continuous “low” signal on the TxD pin might have its root cause in a locked-up
microcontroller or in a short circuit on the printed circuit board, for example. In normal-operating mode, a logical
“low” signal on the TxD pin for the time t > tTxD enables the TxD time-out feature and the TLE7250V disables the
transmitter (see Figure 8). The receiver is still active and the data on the bus continues to be monitored by the
RxD output pin.
t > tTxD
TxD time-out
CANH
CANL
TxD time–out released
t
TxD
t
RxD
t
Figure 8
TxD time-out function
Figure 8 illustrates how the transmitter is deactivated and activated again. A permanent “low” signal on the TxD
input pin activates the TxD time-out function and deactivates the transmitter. To release the transmitter after a TxD
time-out event the TLE7250V requires a signal change on the TxD input pin from logical “low” to logical “high”.
Data Sheet
15
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Fail Safe Functions
5.4
Overtemperature Protection
The TLE7250V has an integrated overtemperature detection to protect the TLE7250V against thermal overstress
of the transmitter. The overtemperature protection is active in normal-operating mode and disabled in power-save
mode. In case of an overtemperature condition, the temperature sensor will disable the transmitter (see Figure 1)
while the transceiver remains in normal-operating mode.
After the device has cooled down the transmitter is activated again (see Figure 9). A hysteresis is implemented
within the temperature sensor.
TJSD (shut down temperature)
TJ
cool down
˂T
switch-on transmitter
t
CANH
CANL
t
TxD
t
RxD
t
Figure 9
Overtemperature protection
5.5
Delay Time for Mode Change
The HS CAN transceiver TLE7250V changes the mode of operation within the time window tMode. During the mode
change the RxD output pin is permanently set to logical “high” and does not reflect the status on the CANH and
CANL input pins (see as an example Figure 14 and Figure 15).
Data Sheet
16
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
General Product Characteristics
6
General Product Characteristics
6.1
Absolute Maximum Ratings
Table 3
Absolute maximum ratings voltages, currents and temperatures1)
All voltages with respect to ground; positive current flowing into pin;
(unless otherwise specified)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
Number
VCC
VIO
VCANH
VCANL
VCAN_Diff
-0.3
–
6.0
V
–
P_6.1.1
-0.3
–
6.0
V
–
P_6.1.2
-40
–
40
V
–
P_6.1.3
-40
–
40
V
–
P_6.1.4
-40
–
40
V
–
P_6.1.5
Voltages at the input pins:
NEN, TxD
VMAX_IN
-0.3
–
6.0
V
–
P_6.1.6
Voltages at the output pin:
RxD
VMAX_OUT -0.3
–
VIO
V
–
P_6.1.7
IRxD
-20
–
20
mA
–
P_6.1.8
Tj
TS
-40
–
150
°C
–
P_6.1.9
-55
–
150
°C
–
P_6.1.10
–
9
kV
HBM
P_6.1.11
(100 pF via 1.5 kΩ)2)
–
2
kV
HBM
P_6.1.12
2)
(100 pF via 1.5 kΩ)
–
750
V
CDM3)
Voltages
Transmitter supply voltage
Digital supply voltage
CANH DC voltage versus GND
CANL DC voltage versus GND
Differential voltage between
CANH and CANL
Currents
RxD output current
Temperatures
Junction temperature
Storage temperature
ESD Resistivity
ESD immunity at CANH, CANL
versus GND
VESD_HBM_ -9
ESD immunity at all other pins
VESD_HBM_ -2
ESD immunity to GND
VESD_CDM -750
CAN
ALL
P_6.1.13
1) Not subject to production test, specified by design
2) ESD susceptibility, Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001
3) ESD susceptibility, Charge Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1
Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability. Integrated protection functions
are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions
are considered as “outside” normal-operating range. Protection functions are not designed for continuos
repetitive operation.
Data Sheet
17
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
General Product Characteristics
6.2
Functional Range
Table 4
Functional range
Parameter
Symbol
Values
Unit
Note /
Test Condition
Number
Min.
Typ.
Max.
VCC
VIO
4.5
–
5.5
V
–
P_6.2.1
3.0
–
5.5
V
–
P_6.2.2
Tj
-40
–
150
°C
1)
P_6.2.3
Supply Voltages
Transmitter supply voltage
Digital supply voltage
Thermal Parameters
Junction temperature
1) Not subject to production test, specified by design.
Note: Within the functional range the IC operates as described in the circuit description. The electrical
characteristics are specified within the conditions given in the related electrical characteristics table.
6.3
Thermal Resistance
Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information,
please visit www.jedec.org.
Table 5
Thermal resistance1)
Parameter
Symbol
Values
Min.
Typ.
Max.
–
55
–
Unit
Note /
Test Condition
Number
K/W
2)
TLE7250VLE
P_6.3.1
TLE7250VSJ
P_6.3.2
Thermal Resistances
Junction to Ambient PG-TSON-8
Junction to Ambient PG-DSO-8
RthJA
RthJA
–
130
–
K/W
2)
150
175
200
°C
–
P_6.3.3
–
10
–
K
–
P_6.3.4
Thermal Shutdown (junction temperature)
Thermal shutdown temperature
Thermal shutdown hysteresis
TJSD
∆T
1) Not subject to production test, specified by design
2) Specified RthJA value is according to Jedec JESD51-2,-7 at natural convection on FR4 2s2p board. The product (TLE7250V)
was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu).
Data Sheet
18
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
7
Electrical Characteristics
7.1
Functional Device Characteristics
Table 6
Electrical characteristics
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note / Test Condition
Number
Current Consumption
Current consumption at VCC
normal-operating mode
ICC
–
2.6
4
mA
“recessive” state,
VTxD = VIO, VNEN = 0 V;
P_7.1.1
Current consumption at VCC
normal-operating mode
ICC
–
38
60
mA
“dominant” state,
VTxD = VNEN = 0 V;
P_7.1.2
Current consumption at VIO
normal-operating mode
IIO
–
–
1
mA
VNEN = 0 V;
P_7.1.3
Current consumption at VCC
power-save mode
ICC(PSM)
–
–
5
µA
VTxD = VNEN = VIO;
P_7.1.4
Current consumption at VIO
power-save mode
IIO(PSM)
–
5
8
µA
VTxD = VNEN = VIO,
0 V < VCC < 5.5 V;
P_7.1.5
VCC(UV,R) 3.8
4.0
4.3
V
–
P_7.1.6
VCC(UV,F) 3.65
3.85
4.3
V
–
P_7.1.7
VCC(UV,H) –
150
–
mV
1)
P_7.1.8
VIO undervoltage monitor
rising edge
VIO(UV,R) 2.0
2.5
3.0
V
–
P_7.1.9
VIO undervoltage monitor
falling edge
VIO(UV,F)
2.3
3.0
V
–
P_7.1.10
VIO undervoltage monitor
VIO(UV,H) –
200
–
mV
1)
P_7.1.11
–
–
100
µs
1)
(see Figure 6 and
Figure 7);
P_7.1.12
P_7.1.13
VRxD = VIO - 0.4 V,
VDiff < 0.5 V;
VRxD = 0.4 V, VDiff > 0.9 V; P_7.1.14
Supply Resets
VCC undervoltage monitor
rising edge
VCC undervoltage monitor
falling edge
VCC undervoltage monitor
hysteresis
1.8
hysteresis
VCC and VIO undervoltage delay tDelay(UV)
time
Receiver Output RxD
“High” level output current
IRD,H
–
-4
-2
mA
“Low” level output current
IRD,L
2
4
–
mA
Data Sheet
19
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
Table 6
Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note / Test Condition
Number
Transmission Input TxD
“High” level input voltage
threshold
VTxD,H
–
0.5
× VIO
0.7
× VIO
V
“recessive” state;
P_7.1.15
“Low” level input voltage
threshold
VTxD,L
0.3
× VIO
0.4
× VIO
–
V
“dominant” state;
P_7.1.16
Pull-up resistance
RTxD
VHYS(TxD)
CTxD
tTxD
10
25
50
kΩ
–
P_7.1.17
mV
1)
P_7.1.18
P_7.1.19
“High” level input voltage
threshold
Input hysteresis
–
450
–
–
–
10
pF
1)
4.5
–
16
ms
normal-operating mode;
P_7.1.20
VNEN,H
–
0.5
× VIO
0.7
× VIO
V
power-save mode;
P_7.1.21
“Low” level input voltage
threshold
VNEN,L
0.3
× VIO
0.4
× VIO
–
V
normal-operating mode;
P_7.1.22
Pull-up resistance
RNEN
10
CNEN
–
VHYS(NEN) –
25
50
kΩ
–
P_7.1.23
pF
1)
P_7.1.24
200
–
mV
1)
P_7.1.25
Differential receiver threshold
“dominant”
normal-operating mode
VDiff_D
–
0.75
0.9
V
2)
P_7.1.26
Differential receiver threshold
“recessive”
normal-operating mode
VDiff_R
0.5
0.66
–
V
2)
P_7.1.27
Common mode range
CMR
-12
–
12
V
VCC = 5 V;
P_7.1.28
P_7.1.29
Input capacitance
TxD permanent “dominant”
time-out
Not Enable Input NEN
Input capacitance
Input hysteresis
–
10
Bus Receiver
Differential receiver hysteresis
normal-operating mode
VDiff,hys
–
90
–
mV
1)
CANH, CANL input resistance
Ri
RDiff
∆R i
10
20
30
kΩ
“recessive” state;
P_7.1.30
20
40
60
kΩ
“recessive” state;
P_7.1.31
“recessive” state;
P_7.1.32
Differential input resistance
Input resistance deviation
between CANH and CANL
Input capacitance CANH, CANL CIn
versus GND
Differential input capacitance
Data Sheet
CIn_Diff
-1
–
1
%
1)
–
20
40
pF
1)
VTxD = VIO;
P_7.1.33
–
10
20
pF
1)
VTxD = VIO;
P_7.1.34
20
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
Table 6
Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note / Test Condition
Number
Bus Transmitter
CANL/CANH “recessive”
output voltage
normal-operating mode
VCANL/H
2.0
2.5
3.0
V
VTxD = VIO,
no load;
P_7.1.35
CANH, CANL “recessive”
output voltage difference
normal-operating mode
VDiff_NM
-500
–
50
mV
VTxD = VIO,
P_7.1.36
CANL “dominant”
output voltage
normal-operating mode
VCANL
0.5
–
2.25
V
VTxD = 0 V;
P_7.1.37
CANH “dominant”
output voltage
normal-operating mode
VCANH
2.75
–
4.5
V
VTxD = 0 V;
P_7.1.38
CANH, CANL “dominant”
output voltage difference
normal-operating mode
according to ISO 11898-2
VDiff = VCANH - VCANL
VDiff
1.5
–
3.0
V
VTxD = 0 V,
50 Ω < RL < 65 Ω,
4.75 < VCC < 5.25 V;
P_7.1.39
CANH, CANL “dominant”
output voltage difference
normal-operating mode
VDiff = VCANH - VCANL
VDiff_R45
1.4
–
3.0
V
VTxD = 0 V,
45 Ω < RL < 50 Ω,
4.75 < VCC < 5.25 V;
P_7.1.40
Driver “dominant” symmetry
normal-operating mode
VSYM = VCANH + VCANL
VSYM
4.5
5
5.5
V
VCC = 5.0 V, VTxD = 0 V;
P_7.1.41
CANL short circuit current
ICANLsc
40
75
100
mA
P_7.1.42
CANH short circuit current
ICANHsc
-100
-75
-40
mA
Leakage current, CANH
ICANH,lk
-5
–
5
µA
Leakage current, CANL
ICANL,lk
-5
–
5
µA
VCANLshort = 18 V,
VCC = 5.0 V, t < tTxD,
VTxD = 0 V;
VCANHshort = 0 V,
VCC = 5.0 V, t < tTxD,
VTxD = 0 V;
VCC = VIO = 0 V,
0 V < VCANH < 5 V,
VCANH = VCANL;
VCC = VIO = 0 V,
0 V < VCANL < 5 V,
VCANH = VCANL;
Data Sheet
no load;
21
P_7.1.43
P_7.1.44
P_7.1.45
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
Table 6
Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note / Test Condition
Number
Dynamic CAN-Transceiver Characteristics
Propagation delay
TxD-to-RxD “low”
(“recessive to “dominant”)
tLoop(H,L)
–
180
255
ns
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
P_7.1.46
Propagation delay
TxD-to-RxD “high”
(“dominant” to “recessive”)
tLoop(L,H)
–
180
255
ns
P_7.1.47
Propagation delay
extended load
TxD-to-RxD “low”
(“recessive to “dominant”)
tLoop_Ext(H –
–
300
ns
Propagation delay
extended load
TxD-to-RxD “high”
(“dominant” to “recessive”)
tLoop_Ext(L –
–
300
ns
Propagation delay
TxD “low” to bus “dominant”
td(L),T
–
90
140
ns
Propagation delay
TxD “high” to bus “recessive”
td(H),T
–
90
140
ns
Propagation delay
bus “dominant” to RxD “low”
td(L),R
–
90
140
ns
Propagation delay
bus “recessive” to RxD “high”
td(H),R
–
90
140
ns
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
1)
CL = 200 pF,
RL = 120 Ω, 4.75 V <
VCC < 5.25 V,
CRxD = 15 pF;
1)
CL = 200 pF,
RL = 120 Ω, 4.75 V <
VCC < 5.25 V,
CRxD = 15 pF;
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF;
tMode
–
–
20
µs
1)
P_7.1.52
,L)
,H)
P_7.1.53
P_7.1.54
P_7.1.48
P_7.1.49
P_7.1.50
P_7.1.51
Delay Times
Delay time for mode change
Data Sheet
22
(see Figure 14 and
Figure 15);
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
Table 6
Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Values
Min.
Unit
Note / Test Condition
Number
Typ.
Max.
500
550
ns
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF,
tBit = 500 ns,
(see Figure 12);
P_7.1.55
500
530
ns
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF,
tBit = 500 ns,
(see Figure 12);
P_7.1.56
–
40
ns
CL = 100 pF,
4.75 V < VCC < 5.25 V,
CRxD = 15 pF,
tBit = 500 ns,
(see Figure 12);
P_7.1.57
CAN FD Characteristics
Received recessive bit width
at 2 MBit/s
tBit(RxD)_2 400
Transmitted recessive bit width
at 2 MBit/s
tBit(Bus)_2 435
Receiver timing symmetry
at 2 MBit/s
∆tRec = tBit(RxD) - tBit(Bus)
ΔtRec_2MB -65
MB
MB
1) Not subject to production test, specified by design.
2) In respect to common mode range.
Data Sheet
23
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
7.2
Diagrams
VIO
7
100 nF
CANH
TxD
NEN
CL
5
1
8
RL
RxD
6
4
CRxD
CANL
GND
VCC
3
100 nF
2
Figure 10
Test circuits for dynamic characteristics
TxD
0.7 x VIO
0.3 x VIO
t
td(L),T
td(H),T
VDiff
0.9 V
0.5 V
t
td(L),R
td(H),R
tLoop(H,L)
tLoop(L,H)
RxD
0.7 x VIO
0.3 x VIO
t
Figure 11
Data Sheet
Timing diagrams for dynamic characteristics
24
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Electrical Characteristics
TxD
0.7 x VIO
0.3 x VIO
0.3 x VIO
5 x tBit
VDiff
tBit
t
tLoop(H,L)
tBit(Bus)
VDiff = VCANH - VCANL
0.9 V
0.5 V
t
tLoop(L,H)
tBit(RxD)
RxD
0.7 x VIO
0.3 x VIO
t
Figure 12
Data Sheet
“Recessive” bit time - five “dominant” bits followed by one “recessive” bit
25
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8
Application Information
8.1
ESD Robustness according to IEC61000-4-2
Test for ESD robustness according to IEC61000-4-2 “Gun test” (150 pF, 330 Ω) have been performed. The results
and test conditions are available in a separate test report.
Table 7
ESD robustness according to IEC61000-4-2
Performed Test
Result
Unit
Remarks
Electrostatic discharge voltage at pin CANH and ≥ +8
CANL versus GND
kV
1)
Positive pulse
Electrostatic discharge voltage at pin CANH and ≤ -8
CANL versus GND
kV
1)
Negative pulse
1) ESD susceptibility “ESD GUN” according to GIFT / ICT paper: “EMC Evaluation of CAN Transceivers, version 03/02/IEC
TS62228”, section 4.3. (DIN EN61000-4-2)
Tested by external test facility (IBEE Zwickau, EMC test report no. TBD).
Data Sheet
26
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8.2
Application Example
VBAT
I
Q1
22 uF
TLE4476D
CANH
CANL
EN
GND
100 nF
100 nF
Q2
3
VCC
22 uF
120
Ohm
VIO
TLE7250VLE
7
6
optional:
common mode choke
NEN
CANH
TxD
RxD
CANL
100 nF
5
8
VCC
Out
1
Out
4
In
Microcontroller
e.g. XC22xx
GND
GND
2
I
Q1
22 uF
TLE4476D
EN
GND
100 nF
Q2
3
VCC
22 uF
VIO
TLE7250VLE
7
6
NEN
CANH
TxD
RxD
CANL
optional:
common mode choke
Figure 13
Data Sheet
8
1
4
100 nF
100 nF
VCC
Out
Out
In
Microcontroller
e.g. XC22xx
GND
120
Ohm
CANH
5
GND
2
CANL
example ECU design
Application circuit
27
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8.3
Examples for Mode Changes
Changing the status on the NEN input pin triggers a change of the operating mode, disregarding the actual signal
on the CANH, CANL and TxD pins (see also Chapter 4.2).
Mode changes are triggered by the NEN pin, when the device TLE7250V is fully supplied. Setting the NEN pin to
logical “low” changes the mode of operation to normal-operating mode:
•
The mode change is executed independently of the signal on the HS CAN bus. The CANH, CANL inputs may
be either “dominant” or “recessive”. They can be also permanently shorted to GND or VCC.
•
A mode change is performed independently of the signal on the TxD input. The TxD input may be either logical
“high” or “low”.
Analog to that, changing the NEN input pin to logical “high” changes the mode of operation to the power-save
mode independent on the signals at the CANH, CANL and TxD pins.
Note: In case the TxD signal is “low” setting the NEN input pin to logical “low” changes the operating mode of the
device to normal-operating mode and drives a “dominant” signal to the HS CAN bus.
Note: The TxD time-out is only effective in normal-operating mode. The TxD time-out timer starts when the
TLE7250V enters normal-operating mode and the TxD input is set to logical “low”.
Data Sheet
28
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8.3.1
Mode Change while the TxD Signal is “low”
The example in Figure 14 shows a mode change to normal-operating mode while the TxD input is logical “low”.
The HS CAN signal is “recessive”, assuming all other HS CAN bus subscribers are also sending a “recessive” bus
signal.
While the transceiver TLE7250V is in power-save mode, the transmitter and the normal-mode receiver are turned
off. The TLE7250V drives no signal to the HS CAN bus nor does it receive any signal from the HS CAN bus.
Changing the NEN to logical “low” turns the mode of operation to normal-operating mode, while the TxD input
signal remains logical “low”. The transmitter and the normal-mode receiver remain disabled until the mode
transition is completed. In normal-operating mode the transmitter and the normal-mode receiver are active. The
“low” signal on the TxD input drives a “dominant” signal to the HS CAN bus and the RxD output becomes logical
“low” following the “dominant” signal on the HS CAN bus.
Changing the NEN pin back to logical “high”, disables the transmitter and normal-mode receiver again. The RxD
output pin is blocked and set to logical “high” with the start of the mode transition. The TxD input and the transmitter
are blocked and the HS CAN bus becomes “recessive”.
Note: The signals on the HS CAN bus are “recessive”, the “dominant” signal is
generated by the TxD input signal
t = tMode
t = tMode
NEN
t
TxD
t
VDiff
t
RxD
t
power-save
transition
normal-operating
transition
power-save mode
normal-mode
receiver disabled
RxD output
blocked
normal-mode receiver
active
RxD output
blocked
normal-mode receiver
disabled
TxD input and transmitter
blocked
Figure 14
Data Sheet
TxD input and transmitter
active
TxD input and transmitter blocked
Example for a mode change while the TxD is “low”
29
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8.3.2
Mode Change while the Bus Signal is “dominant”
The example in Figure 15 shows a mode change while the bus is “dominant” and the TxD input signal is set to
logical “high”.
While the transceiver TLE7250V is in power-save mode, the transmitter and the normal-mode receiver are turned
off. The TLE7250V drives no signal to the HS CAN bus nor does it receive any signal from the HS CAN bus.
Changing the NEN to logical “low” turns the mode of operation to normal-operating mode, while the TxD input
signal remains logical “high”. The transmitter and the normal-mode receiver remain disabled until the mode
transition is completed. In normal-operating mode the transmitter of TLE7250V remains “recessive”, because of
the logical “high” signal on the TxD input. The normal-mode receiver becomes active and the RxD output signal
changes to logical “low” following the “dominant” signal on the HS CAN bus.
Changing the NEN pin back to logical “high”, disables the transmitter and normal-mode receiver again. The RxD
output pin is blocked and set to logical “high” with the start of the mode transition.
Note: The “dominant” signal on the HS CAN bus is set by another HS CAN bus
subscriber.
t = tMode
t = tMode
NEN
t
TxD
t
VDiff
t
RxD
power-save mode
transition
normal-operating
transition
t
power-save mode
normal-mode receiver
disabled
RxD output
blocked
normal-mode receiver
active
RxD output
blocked
normal-mode receiver
disabled
TxD input and transmitter blocked
Figure 15
Data Sheet
TxD input and transmitter
active
TxD input and transmitter blocked
Example for a mode change while the HS CAN is “dominant”
30
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Application Information
8.4
Further Application Information
•
Please contact us for information regarding the pin FMEA.
•
Existing application note.
•
For further information you may visit: http://www.infineon.com/
Data Sheet
31
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Package Outline
0 +0.05
1±0.1
Package Outline
0.3 ±0.1
Pin 1 Marking
1.63 ±0.1
0.56 ±0.1
0.25 ±0.1
3 ±0.1
0.05
Z
0.38 ±0.1
0.4 ±0.1
3 ±0.1
2.4 ±0.1
1.58 ±0.1
0.1 ±0.1
0.81 ±0.1
0.2 ±0.1
9
0.65 ±0.1
Pin 1 Marking
0.3 ±0.1
PG-TSON-8-1-PO V01
Z (4:1)
0.07 MIN.
PG-TSON-8 (Plastic Thin Small Outline Nonleaded PG-TSON-8-1)
0.1
2)
0.41+0.1
-0.06
0.2
8
5
1
4
5 -0.2 1)
M
0.19 +0.06
C
B
8 MAX.
1.27
0.35 x 45˚
4 -0.2 1)
1.75 MAX.
0.175 ±0.07
(1.45)
Figure 16
0.64 ±0.25
6 ±0.2
A B 8x
0.2
M
C 8x
A
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Lead width can be 0.61 max. in dambar area
GPS01181
Figure 17
PG-DSO-8 (Plastic Dual Small Outline PG-DSO-8-44)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with
government regulations the device is available as a green product. Green products are RoHS compliant (i.e
Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.
Data Sheet
32
Dimensions in mm
Rev. 1.0, 2015-08-12
TLE7250VLE
TLE7250VSJ
Revision History
10
Revision History
Revision
Date
Changes
1.00
2015-08-12
Data Sheet created.
Data Sheet
33
Rev. 1.0, 2015-08-12
Edition 2015-08-12
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2006 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.