ge an Ch - S ub je ct to Industrial High Speed CAN-FD Transceiver CAN with Flexible Data-Rate Pr el im in ar y IFX1051LE Preliminary Data Sheet Rev. 0.92, 2015-07-28 Standard Power IFX1051LE PRELIMINARY Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 3.1 3.2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 4.1 4.2 4.2.1 4.2.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 High Speed CAN Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Normal-operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Receive-only Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Power-up and Undervoltage Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Power-down State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Forced Power-save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Undervoltage on the Digital Supply VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Undervoltage on the Transmitter Supply VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Voltage Adaption to the Microcontroller Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 5.1 5.2 5.3 5.4 5.5 Fail Safe Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unconnected Logic Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxD Time-out Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overtemperature Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delay Time for Mode Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 14 14 15 15 6 6.1 6.2 6.3 General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 16 17 17 7 7.1 7.2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Functional Device Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 8.1 8.2 8.3 8.3.1 8.3.2 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESD Robustness according to IEC61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Examples for Mode Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode Change while the TxD Signal is “low” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode Change while the Bus Signal is “dominant” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Preliminary Data Sheet 25 25 26 27 28 29 Pr el im in ar y - S ub je ct to Ch an ge 1 2 Rev. 0.92, 2015-07-28 PRELIMINARY Industrial High Speed CAN-FD Transceiver Overview ge 1 IFX1051LE an Features Fully compatible to ISO 11898-2 • Wide common mode range for electromagnetic immunity (EMI) • Very low electromagnetic emission (EME) • Excellent ESD robustness • Guaranteed loop delay symmetry to support CAN FD data frames up to 2 MBit/s • • VIO input for voltage adaption to the microcontroller supply Extended supply range on VCC and VIO supply CAN short circuit proof to ground, battery and VCC • TxD time-out function with very long TxD timeout timing • Low CAN bus leakage current in power-down state • Overtemperature protection • Protected against transients • Receive-only mode • Green Product (RoHS compliant) • Tiny package: PG-TSON-8 - S ub je ct to PG-TSON-8 y • Ch • ar Description Pr el im in The IFX1051 is a transceiver designed for HS CAN networks in industrial applications. Acting as interface between the physical bus layer and the CAN protocol controller, the IFX1051 drives the signals to the bus and protects the microcontroller against interferences generated within the network. Based on the high symmetry of the CANH and CANL signals, the IFX1051 provides a very low level of electromagnetic emission (EME) within a wide frequency range. The IFX1051 is available in a small, leadless PG-TSON-8 package. The package is RoHS compliant and halogen free and moreover supports the solder joint requirements for automated optical inspection (AOI). The IFX1051LE is fulfilling or exceeding the requirements of the ISO11898-2. The IFX1051 provides a digital supply input VIO and a receive-only mode. It is designed to fulfill the enhanced physical layer requirements for CAN FD and supports data rates up to 2 MBit/s. On the basis of a very low leakage current on the HS CAN bus interface the IFX1051 provides an excellent passive behavior in power-down state. These and other features make the IFX1051 exceptionally suitable for mixed supply HS CAN networks. The IFX1051 provides excellent ESD immunity together with a very high electromagnetic immunity (EMI). Two different operating modes, additional fail-safe features like a TxD time-out and the optimized output slew rates Type Package Marking IFX1051LE PG-TSON-8 1051LE Preliminary Data Sheet 3 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Overview on the CANH and CANL signals make the IFX1051 the ideal choice for large HS CAN networks with high data transmission rates. The qualification of this product is based on JEDEC JESD47 and may reference existing qualification results of similar products. Such referring is justified by the structural similarity of the products. The product is not qualified and manufactured according to the requirements of Infineon Technologies with regard to automotive and/or transportation applications. Infineon Technologies administrates a comprehensive qualify management system according to the latest version of the ISO9001 and ISO/TS 16949 Pr el im in ar y - S ub je ct to Ch an ge The most updated certificates of the aforesaid ISO9001 and ISOTS 16949 are available on the Infineon Technologies webpage http://www.infineon.com/cms/en/product/technology/quality/ Preliminary Data Sheet 4 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 2 Block Diagram Block Diagram 3 5 Tempprotection 6 Timeout Mode control Receiver 1 VIO TxD an Driver Ch CANL 7 - S ub je ct to CANH ge Transmitter VCC 8 RM Normal-mode receiver im Functional block diagram Pr el Figure 1 in GND 2 ar Bus-biasing RxD y VCC/2 = 4 Preliminary Data Sheet 5 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 3 Pin Configuration 3.1 Pin Assignment 1 8 RM GND 2 7 CANH VCC 3 6 CANL RxD 4 5 an TxD ge Pin Configuration Ch PAD - S ub je ct to VIO (Top-side x-ray view) Figure 2 Pin configuration 3.2 Pin Definitions Table 1 Pin definitions and functions Symbol Function 1 TxD Transmit Data Input; internal pull-up to VIO, “low” for “dominant” state. 2 GND Ground 3 VCC Transmitter Supply Voltage; 100 nF decoupling capacitor to GND required. 4 RxD Receive Data Output; “low” in “dominant” state. 5 VIO Digital Supply Voltage; supply voltage input to adapt the logical input and output voltage levels of the transceiver to the microcontroller supply, 100 nF decoupling capacitor to GND required. 6 CANL 7 CANH 8 RM Receive-only Mode Input; internal pull-down to GND, “low” for normal-operating mode. PAD – Connect to PCB heat sink area. Do not connect to other potential than GND. el im in ar y Pin No. Pr CAN Bus Low Level I/O; “low” in “dominant” state. Preliminary Data Sheet CAN Bus High Level I/O; “high” in “dominant” state. 6 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 4 Functional Description Functional Description High Speed CAN Physical Layer Ch an 4.1 ge HS CAN is a serial bus system that connects microcontrollers, sensors and actuators for real-time control applications. The use of the Controller Area Network (abbreviated CAN) is described by the international standard ISO 11898. According to the 7-layer OSI reference model the physical layer of a HS CAN bus system specifies the data transmission from one CAN node to all other available CAN nodes within the network. The physical layer specification of a CAN bus system includes all electrical and mechanical specifications of a CAN network. The CAN transceiver is part of the physical layer specification. Several different physical layer standards of CAN networks have been developed in recent years. The IFX1051 is a High Speed CAN transceiver without a wakeup function and defined by the international standard ISO 11898-2. VIO = VCC = TxD = TxD - S ub je ct to VIO t CANH CANL VCC RxD = CANH = CANL = VDiff = Digital supply voltage Transmitter supply voltage Transmit data input from the microcontroller Receive data output to the microcontroller Bus level on the CANH input/output Bus level on the CANL input/output Differential voltage between CANH and CANL VDiff = VCANH – VCANL t VCC ar y VDiff “dominant” receiver threshold in “recessive” receiver threshold tLoop(H,L) Figure 3 Pr el VIO im RxD t tLoop(L,H) t High speed CAN bus signals and logic signals Preliminary Data Sheet 7 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Functional Description Pr el im in ar y - S ub je ct to Ch an ge The IFX1051 is a High-Speed CAN transceiver, operating as an interface between the CAN controller and the physical bus medium. A HS CAN network is a two wire, differential bus network which allows data transmission rates for CAN FD frames up to 2 MBit/s. Main characteristics for HS CAN networks are the two signal states on the HS CAN bus: “dominant” and “recessive” (see Figure 3). VCC, VIO and GND are the supply pins for the IFX1051. The pins CANH and CANL are the interface to the HS CAN bus and operate in both directions, as an input and as an output. RxD and TxD pins are the interface to the CAN controller, the TxD pin is an input pin and the RxD pin is an output pin. The RM pin is the input pin for the mode selection (see Figure 4). By setting the TxD input pin to logical “low” the transmitter of the IFX1051 drives a “dominant” signal to the CANH and CANL pins. Setting TxD input to logical “high” turns off the transmitter and the output voltage on CANH and CANL discharges towards the “recessive” level. The “recessive” output voltage is provided by the bus biasing (see Figure 1). The output of the transmitter is considered to be “dominant”, when the voltage difference between CANH and CANL is at least higher than 1.5 V (VDiff = VCANH - VCANL). Parallel to the transmitter the normal-mode receiver monitors the signal on the CANH and CANL pins and indicates it on the RxD output pin. A “dominant” signal on the CANH and CANL pins sets the RxD output pin to logical “low”, vice versa a “recessive” signal sets the RxD output to logical “high”. The normal-mode receiver considers a voltage difference (VDiff) between CANH and CANL above 0.9 V as “dominant” and below 0.5 V as “recessive”. To be conform with HS CAN features, like the bit to bit arbitration, the signal on the RxD output has to follow the signal on the TxD input within a defined loop delay tLoop ≤ 255 ns. The thresholds of the digital inputs (TxD and RM) and also the RxD output voltage are adapted to the digital power supply VIO. Preliminary Data Sheet 8 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 4.2 Functional Description Modes of Operation The IFX1051 supports two different modes of operation, receive-only mode and normal-operating mode while the transceiver is supplied according to the specified functional range. The mode of operation is selected by the RM input pin (see Figure 4). receive-only mode VIO > VIO(UV,R) ge VCC > VCC(UV) an RM = 1 RM = 1 normal-operating mode VCC > VCC(UV,R) - S ub je ct to VIO > VIO(UV,R) Ch RM = 0 RM = 0 Figure 4 Mode state diagram 4.2.1 Normal-operating Mode In normal-operating mode the transmitter and the receiver of the HS CAN transceiver IFX1051 are active (see Figure 1). The HS CAN transceiver sends the serial data stream on the TxD input pin to the CAN bus. The data on the CAN bus is displayed at the RxD pin simultaneously. A logical “low” signal on the RM pin selects the normaloperating mode, while the transceiver is supplied by VCC and VIO (see Table 2 for details). 4.2.2 Receive-only Mode ar y In receive-only mode the normal-mode receiver is active and the transmitter is turned off. The IFX1051 can receive data from the HS CAN bus, but cannot send any data to the HS CAN bus. Pr el im in A logical “high” signal on the RM pin selects the receive-only mode, while the transceiver is supplied by VCC and VIO (see Table 2 for details). Preliminary Data Sheet 9 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 4.3 Functional Description Power-up and Undervoltage Condition By detecting an undervoltage event, either on the transmitter supply VCC or the digital supply VIO, the transceiver IFX1051 changes the mode of operation. When the digital power supply VIO is switched off, the transceiver powers down and remains in the power-down state. When switching off the transmitter supply VCC, the transceiver changes to the forced power-save mode, (details see Figure 5). VIO 0 “on” “on” VIO “on” VCC “on” RM “0” power-down state VCC VIO “X” “X” “off” VIO “on” VCC “on” RM “1” receive-only mode VIO “on” VCC “on” RM “1” Power-up and undervoltage Table 2 Modes of operation VCC VIO 1 “on” “on” RM VCC VIO “X” “off” “on” VIO “on” VCC “on” RM “1” VIO “on” VCC “off” RM “1” VIO Normal-operating “low” “on” Receive-only “high” “on” “on” “X” Bus Bias Transmitter Normal-mode Low-power Receiver Receiver “on” “on” not available “on” VCC/2 VCC/2 “off” “on” not available “off” floating “off” “off” not available “X” floating “off” “off” not available “on” “off” Pr Power-down state el Forced power-save “X” VCC in RM im Mode ar y Figure 5 RM VIO “on” VCC “on” RM “0” forced power-save mode - S ub je ct to RM VIO “on” VCC “off” RM “X” VIO “on” VCC “off” RM “0” an VCC Ch RM ge normal-operating mode VIO “on” VCC “on” RM “0” Preliminary Data Sheet 10 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 4.3.1 Functional Description Power-down State Independent of the transmitter supply VCC and of the RM input pin, the IFX1051 is in power-down state when the digital supply voltage VIO is turned off (see Figure 5). In the power-down state the input resistors of the receiver are disconnected from the bus biasing VCC/2. The CANH and CANL bus interface of the IFX1051 is floating and acts as a high-impedance input with a very small leakage current. The high-ohmic input does not influence the “recessive” level of the CAN network and allows an optimized EME performance of the entire HS CAN network (see also Table 2). Forced Power-save Mode ge 4.3.2 The forced power-save mode is a fail-safe mode to avoid any disturbance on the HS CAN bus, while the IFX1051 faces a loss of the transmitter supply VCC. an In forced power-save mode, the transmitter and the normal-mode receiver are turned off and therefore the transceiver IFX1051 can not disturb the bus media. Ch The RxD output pin is permanently set to logical “high”. The bus biasing is floating (details see Table 2). 4.3.3 - S ub je ct to The forced power-save mode can only be entered when the transmitter supply VCC is not available, either by powering up the digital supply VIO only or by turning off the transmitter supply in normal-operating mode or in receive-only mode (see Figure 5). While the transceiver IFX1051 is in forced power-save mode the RM pin is disabled. Power-up The HS CAN transceiver IFX1051 powers up if at least the digital supply VIO is connected to the device. By default the device powers up in normal-operating mode, due to the internal pull-down resistor on the RM pin to GND. In case the device needs to power-up in receive-only mode, the RM pin needs to be pulled active to logical “high” and the supplies VIO and VCC have to be connected. Pr el im in ar y By supplying only the digital power supply VIO the IFX1051 powers up in forced power-save mode (see Figure 5). Preliminary Data Sheet 11 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Functional Description Undervoltage on the Digital Supply VIO 4.3.4 If the voltage on VIO supply input falls below the threshold VIO < VIO(U,F), the transceiver IFX1051 powers down and changes to the power-down state. The undervoltage detection on the digital supply VIO has the highest priority and is independent of the transmitter supply VCC and also independent of the currently selected operating mode. An undervoltage event on VIO always powers down the IFX1051. ge transmitter supply voltage VCC = “don’t care” VIO an VIO undervoltage monitor VIO(UV,R) hysteresis VIO(UV,H) Ch VIO undervoltage monitor VIO(UV,F) any mode of operation power-down state RM “X” = don’t care 1)assuming t normal-operating mode “low” due the internal pull-down resistor1) t no external signal applied Undervoltage on the digital supply VIO Pr el im in ar y Figure 6 - S ub je ct to tDelay(UV) delay time undervoltage Preliminary Data Sheet 12 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Functional Description Undervoltage on the Transmitter Supply VCC 4.3.5 In case the transmitter supply VCC falls below the threshold VCC < VCC(UV,F), the transceiver IFX1051 changes the mode of operation to forced power-save mode. The transmitter and also the normal-mode receiver of the IFX1051 are powered by the VCC supply. In case of an insufficient VCC supply, the IFX1051 can neither transmit the CANH and CANL signals correctly to the bus, nor can it receive them properly. Therefore the IFX1051 blocks the transmitter and the receiver in forced power-save mode (see Figure 7). ge The undervoltage detection on the transmitter supply VCC is active in normal-operating mode and in receive-only mode (see Figure 5). an digital supply voltage VIO = “on” Ch VCC VCC undervoltage monitor VCC(UV,R) - S ub je ct to hysteresis VCC(UV,H) VCC undervoltage monitor VCC(UV,F) tDelay(UV) delay time undervoltage any mode of operation forced power-save mode RM “X” = don’t care normal-operating mode “low” due the internal pull-down resistor1) t no external signal applied y 1)assuming t Undervoltage on the transmitter supply VCC 4.3.6 Voltage Adaption to the Microcontroller Supply in ar Figure 7 im The HS CAN transceiver IFX1051 has two different power supplies, VCC and VIO. The power supply VCC supplies the transmitter and the normal-mode receiver. The power supply VIO supplies the digital input and output buffers and it is also the main power domain of the internal logic. el To adjust the digital input and output levels of the IFX1051 to the I/O levels of the external microcontroller, connect the power supply VIO to the microcontroller I/O supply voltage (see Figure 13). Pr Note: In case the digital supply voltage VIO is not required in the application, connect the digital supply voltage VIO to the transmitter supply VCC. Preliminary Data Sheet 13 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Fail Safe Functions 5 Fail Safe Functions 5.1 Short Circuit Protection The CANH and CANL bus outputs are short circuit proof, either against GND or a positive supply voltage. A current limiting circuit protects the transceiver against damages. If the device is heating up due to a continuous short on the CANH or CANL, the internal overtemperature protection switches off the bus transmitter. Unconnected Logic Pins ge 5.2 5.3 Ch an All logic input pins have an internal pull-up resistor to VIO or a pull-down resistor to GND. In case the VIO supply is activated and the logical pins are open, the IFX1051 enters into the normal-operating mode by default. The TxD input is pulled to logical “high” due to the internal pull-up resistor to VIO. The HS CAN transceiver IFX1051 will not influence the data on the CAN bus as long the TxD input pin remains logical “high”. TxD Time-out Function - S ub je ct to The TxD time-out feature protects the CAN bus against being permanently blocked in case the logical signal at the TxD pin is continuously “low”. A continuous “low” signal at the TxD pin might have its root cause in a lockedup microcontroller or in a short circuit on the printed circuit board, for example. In normal-operating mode, a logical “low” signal applied to the TxD pin for the time t > tTxD triggers the TxD time-out feature and the IFX1051 disables the transmitter (see Figure 8). The receiver is still active and the data on the bus continues to be monitored by the RxD output pin. t > tTxD TxD time-out ar TxD t in t im RxD el t TxD time-out function Pr Figure 8 TxD time–out released y CANH CANL Figure 8 illustrates how the transmitter is deactivated and activated again. A permanent “low” signal on the TxD input pin activates the TxD time-out function and deactivates the transmitter. To release the transmitter after a TxD time-out event the IFX1051 requires a signal change on the TxD input pin from logical “low” to logical “high”. Preliminary Data Sheet 14 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 5.4 Fail Safe Functions Overtemperature Protection The IFX1051 has an integrated overtemperature detection to protect the IFX1051 against thermal overstress of the transmitter. The overtemperature protection is active in normal-operating mode and disabled in receive-only mode. In case of an overtemperature condition, the temperature sensor will disable the transmitter (see Figure 1) while the transceiver remains in normal-operating mode. TJSD (shut down temperature) TJ ge After the device has cooled down the transmitter is activated again (see Figure 9). A hysteresis is implemented within the temperature sensor circuit. cool down an ˂T Ch switch-on transmitter - S ub je ct to CANH CANL TxD t t t y RxD t Overtemperature protection 5.5 Delay Time for Mode Change in ar Figure 9 Pr el im The HS CAN transceiver IFX1051 changes the mode of operation within the time window tMode. During the mode change the normal-mode receiver and the RxD output are active and reflect the on the HS CAN input pins (see as an example Figure 14 and Figure 15). Preliminary Data Sheet 15 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY General Product Characteristics 6 General Product Characteristics 6.1 Absolute Maximum Ratings Table 3 Absolute maximum ratings voltages, currents and temperatures1) Symbol Values Unit Note / Test Condition Number an Parameter ge All voltages with respect to ground; positive current flowing into pin; (unless otherwise specified) Min. Typ. Max. -0.3 – 6.0 V -0.3 – 6.0 V -40 – 40 V -40 – 40 – Voltages -40 – P_6.1.2 – P_6.1.3 V – P_6.1.4 40 V – P_6.1.5 – 6.0 V – P_6.1.6 Ch P_6.1.1 Voltages at the input pins: RM, TxD VMAX_IN Voltages at the output pin: RxD VMAX_OUT -0.3 – VIO V – P_6.1.7 IRxD -20 – 20 mA – P_6.1.8 Tj TS -40 – 150 °C – P_6.1.9 – 150 °C – P_6.1.10 ESD immunity at CANH, CANL VESD_HBM_ -8 versus GND CAN – 8 kV HBM (100 pF via 1.5 kΩ)2) P_6.1.11 ESD immunity at all other pins in CANH and CANL – - S ub je ct to VCC Digital supply voltage VIO CANH DC voltage versus GND VCANH CANL DC voltage versus GND VCANL Differential voltage between VCAN_Diff Transmitter supply voltage VESD_HBM_ -2 – 2 kV HBM (100 pF via 1.5 kΩ)2) P_6.1.12 ESD immunity to GND VESD_CDM -750 – 750 V CDM3) P_6.1.13 -0.3 Currents RxD output current Temperatures Junction temperature Storage temperature -55 ar y ESD Resistivity im ALL Pr el 1) Not subject to production test, specified by design 2) ESD susceptibility, Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001 3) ESD susceptibility, Charge Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1 Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal-operating range. Protection functions are not designed for continuos repetitive operation. Preliminary Data Sheet 16 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY General Product Characteristics 6.2 Functional Range Table 4 Functional range Parameter Symbol Values Unit Note / Test Condition Number P_6.2.1 Min. Typ. Max. VCC VIO 4.5 – 5.5 V – 3.0 – 5.5 V – Tj -40 – 125 °C Transmitter supply voltage Digital supply voltage ge Supply Voltages Junction temperature 1) P_6.2.3 Ch 1) Not subject to production test, specified by design. an Thermal Parameters P_6.2.2 6.3 Thermal Resistance - S ub je ct to Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the related electrical characteristics table. Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, please visit www.jedec.org. Table 5 Thermal resistance1) Parameter Symbol Thermal Resistances RthJA Junction to Ambient PG-TSON-8 TJSD ∆T Thermal shutdown temperature Note / Test Condition Number Typ. Max. – 55 – K/W 2) P_6.3.1 150 175 200 °C – P_6.3.2 – 10 – K – P_6.3.3 ar Thermal shutdown hysteresis Unit Min. y Thermal Shutdown (junction temperature) Values Pr el im in 1) Not subject to production test, specified by design 2) Specified RthJA value is according to Jedec JESD51-2,-7 at natural convection on FR4 2s2p board. The product (IFX1051) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu). Preliminary Data Sheet 17 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Electrical Characteristics Electrical Characteristics 7.1 Functional Device Characteristics Table 6 Electrical characteristics ge 7 Symbol Values Min. Typ. Max. 2.6 4 Unit Note / Test Condition Number mA Ch Parameter “recessive” state, VTxD = VIO, VRM = 0 V; P_7.1.1 ICC – Current consumption at VCC normal-operating mode ICC – Current consumption at VIO normal-operating mode IIO – Current consumption at VCC receive-only mode ICC(ROM) – Current consumption at VIO receive-only mode IIO(ROM) – Supply Resets VCC undervoltage monitor VCC(UV,R) 3.8 rising edge VCC(UV,F) 3.65 ar falling edge VCC undervoltage monitor 38 60 mA “dominant” state, VTxD = VRM = 0 V; P_7.1.2 – 1 mA VRM = 0 V; P_7.1.3 – 2 mA VRM = VTxD = VIO; P_7.1.4 – 1 mA VRM = VIO; P_7.1.5 4.0 4.3 V – P_7.1.6 3.85 4.3 V – P_7.1.26 150 – mV 1) P_7.1.7 y VCC undervoltage monitor - S ub je ct to Current Consumption Current consumption at VCC normal-operating mode an 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 125 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. VCC(UV,H) – VIO undervoltage monitor rising edge VIO(UV,R) 2.0 2.5 3.0 V – P_7.1.8 VIO undervoltage monitor falling edge im in hysteresis 2.3 3.0 V – P_7.1.27 200 – mV 1) P_7.1.9 – – 100 µs 1) (see Figure 6 and Figure 7); P_7.1.10 P_7.1.11 VIO(UV,H) – Pr hysteresis VCC and VIO undervoltage delay tDelay(UV) time 1.8 el VIO undervoltage monitor VIO(UV,F) Receiver Output RxD “High” level output current IRD,H – -4 -2 mA VRxD = VIO - 0.4 V, VDiff < 0.5 V; “Low” level output current IRD,L 2 4 – mA VRxD = 0.4 V, VDiff > 0.9 V; P_7.1.12 Preliminary Data Sheet 18 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Table 6 Electrical Characteristics Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 125 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Number Transmission Input TxD VTxD,H – 0.5 × VIO 0.7 × VIO V “recessive” state; P_7.1.13 “Low” level input voltage threshold VTxD,L 0.3 × VIO 0.4 × VIO – V “dominant” state; P_7.1.14 Pull-up resistance RTxD 10 25 50 kΩ – P_7.1.15 mV 1) P_7.1.17 P_7.1.16 Input capacitance CTxD – – 10 pF 1) TxD permanent “dominant” timeout tTxD Ch an ge “High” level input voltage threshold 4.5 – 16 ms normal-operating mode; P_7.1.18 “High” level input voltage threshold VRM,H – “Low” level input voltage threshold VRM,L 0.3 × VIO Pull-down resistance RRM 10 Input capacitance CRM – VHYS(TxD) – 450 Receive-only Input RM VHYS(RM) – Input hysteresis Bus Receiver VDiff_D Differential receiver threshold “recessive” normal-operating mode and receive-only mode VDiff_R VDiff,hys Pr Differential receiver hysteresis normal-operating mode 0.7 × VIO V receive-only mode; P_7.1.19 0.4 × VIO – V normal-operating mode; P_7.1.20 25 50 kΩ – P_7.1.21 – 10 pF 1) P_7.1.22 P_7.1.23 200 – mV 1) 0.75 0.9 V 2) P_7.1.24 ar 0.5 0.66 – V 2) P_7.1.25 – 12 V VCC = 5 V; P_7.1.28 in im CMR el Common mode range – 0.5 × VIO y Differential receiver threshold “dominant” normal-operating mode and receive-only mode – - S ub je ct to Input hysteresis -12 – 90 – mV CANH, CANL input resistance Ri 10 20 30 kΩ Differential input resistance RDiff 20 40 60 Input resistance deviation between CANH and CANL ∆R i Input capacitance CANH, CANL CIn versus GND Differential input capacitance Preliminary Data Sheet CIn_Diff 1) P_7.1.29 “recessive” state; P_7.1.30 kΩ “recessive” state; P_7.1.31 “recessive” state; P_7.1.32 -1 – 1 % 1) – 20 40 pF 1) VTxD = VIO; P_7.1.33 – 10 20 pF 1) VTxD = VIO; P_7.1.34 19 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Table 6 Electrical Characteristics Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 125 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Number P_7.1.35 VCANL/H 2.0 2.5 3.0 V VTxD = VIO, no load; CANH, CANL “recessive” output voltage difference normal-operating mode VDiff_NM -500 – 50 mV VTxD = VIO, no load; CANL “dominant” output voltage normal-operating mode VCANL 0.5 – 2.25 V VTxD = 0 V; CANH “dominant” output voltage normal-operating mode VCANH 2.75 CANH, CANL “dominant” output voltage difference normal-operating mode according to ISO 11898-2 VDiff = VCANH - VCANL VDiff 1.5 CANH, CANL “dominant” output voltage difference normal-operating mode VDiff = VCANH - VCANL VDiff_R45 1.4 Driver “dominant” symmetry normal-operating mode VSYM = VCANH + VCANL VSYM 4.5 CANL short circuit current ICANLsc CANH short circuit current Leakage current, CANL Preliminary Data Sheet an Ch P_7.1.36 - S ub je ct to P_7.1.38 4.5 V VTxD = 0 V; P_7.1.39 – 3.0 V VTxD = 0 V, 50 Ω < RL < 65 Ω, 4.75 < VCC < 5.25 V; P_7.1.40 – 3.0 V VTxD = 0 V, 45 Ω < RL < 50 Ω, 4.75 < VCC < 5.25 V; P_7.1.37 5 5.5 V VCC = 5.0 V, VTxD = 0 V; P_7.1.41 40 75 100 mA VCANLshort = 18 V, VCC = 5.0 V, t < tTxD, VTxD = 0 V; P_7.1.42 -100 -75 -40 mA VCANHshort = 0 V, VCC = 5.0 V, t < tTxD, VTxD = 0 V; P_7.1.43 ICANH,lk -5 – 5 µA VCC = VIO = 0 V, 0 V < VCANH < 5 V, VCANH = VCANL; P_7.1.44 ICANL,lk -5 – 5 µA VCC = VIO = 0 V, 0 V < VCANL < 5 V, VCANH = VCANL; P_7.1.45 in ar y – el ICANHsc Pr Leakage current, CANH ge CANL/CANH “recessive” output voltage normal-operating mode im Bus Transmitter 20 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Table 6 Electrical Characteristics Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 125 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note / Test Condition Number Dynamic CAN-Transceiver Characteristics tLoop(H,L) – 180 255 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.46 Propagation delay TxD-to-RxD “high” (“dominant” to “recessive”) tLoop(L,H) – 180 255 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.47 Propagation delay extended load TxD-to-RxD “low” (“recessive to “dominant”) tLoop_Ext(H – – 300 ns 1) P_7.1.52 Propagation delay extended load TxD-to-RxD “high” (“dominant” to “recessive”) tLoop_Ext(L – Propagation delay TxD “low” to bus “dominant” td(L),T – Propagation delay TxD “high” to bus “recessive” td(H),T – Propagation delay bus “dominant” to RxD “low” td(L),R – Propagation delay bus “recessive” to RxD “high” td(H),R ar – – an ns 1) CL = 200 pF, RL = 120 Ω, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.54 90 140 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.48 90 140 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.49 90 140 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.50 90 140 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; P_7.1.51 – 20 µs 1) P_7.1.53 in tMode Ch - S ub je ct to 300 y ,H) – (see Figure 14 and Figure 15); Pr el Delay time for mode change CL = 200 pF, RL = 120 Ω, 4.75 V < VCC < 5.25 V, CRxD = 15 pF; ,L) im Delay Times ge Propagation delay TxD-to-RxD “low” (“recessive to “dominant”) Preliminary Data Sheet 21 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Table 6 Electrical Characteristics Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < 125 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Unit Note / Test Condition Number Typ. Max. 500 550 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF, tBit = 500 ns, (see Figure 12); P_7.1.55 500 530 ns CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF, tBit = 500 ns, (see Figure 12); P_7.1.56 CL = 100 pF, 4.75 V < VCC < 5.25 V, CRxD = 15 pF, tBit = 500 ns, P_7.1.57 Transmitted recessive bit width at 2 MBit/s tBit(Bus)_2 435 Receiver timing symmetry at 2 MBit/s ∆tRec = tBit(RxD) - tBit(Bus) ΔtRec_2MB -65 MB - S ub je ct to MB an tBit(RxD)_2 400 Ch Received recessive bit width at 2 MBit/s ge CAN FD Characteristics – 40 ns (see Figure 12); Pr el im in ar y 1) Not subject to production test, specified by design. 2) In respect to common mode range. Preliminary Data Sheet 22 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Diagrams VIO 100 nF TxD RM CL ge CANH 1 8 an 7 5 RL RxD GND VCC 3 100 nF 2 Figure 10 CRxD CANL - S ub je ct to 6 4 Ch 7.2 Electrical Characteristics Test circuits for dynamic characteristics TxD 0.7 x VIO 0.3 x VIO td(L),T y td(H),T ar VDiff t 0.5 V in 0.9 V im t td(L),R tLoop(L,H) el tLoop(H,L) td(H),R Pr RxD 0.7 x VIO 0.3 x VIO t Figure 11 Timing diagrams for dynamic characteristics Preliminary Data Sheet 23 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Electrical Characteristics TxD 0.7 x VIO 0.3 x VIO 0.3 x VIO VDiff tBit t tLoop(H,L) ge 5 x tBit tBit(Bus) VDiff = VCANH - VCANL an 0.9 V tLoop(L,H) RxD t Ch 0.5 V tBit(RxD) 0.3 x VIO t “Recessive” bit time - five “dominant” bits followed by one “recessive” bit Pr el im in ar y Figure 12 - S ub je ct to 0.7 x VIO Preliminary Data Sheet 24 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Application Information 8 Application Information 8.1 ESD Robustness according to IEC61000-4-2 Test for ESD robustness according to IEC61000-4-2 “Gun test” (150 pF, 330 Ω) have been performed. The results and test conditions are available in a separate test report. Table 7 ESD robustness according to IEC61000-4-2 Unit Remarks Electrostatic discharge voltage at pin CANH and ≥ +8 CANL versus GND kV 1) Positive pulse Electrostatic discharge voltage at pin CANH and ≤ -8 CANL versus GND kV 1) Negative pulse ge Result an Performed Test Pr el im in ar y - S ub je ct to Ch 1) ESD susceptibility “ESD GUN” according to GIFT / ICT paper: “EMC Evaluation of CAN Transceivers, version 03/02/IEC TS62228”, section 4.3. (DIN EN61000-4-2) Tested by external test facility (IBEE Zwickau). Preliminary Data Sheet 25 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY Application Example Q1 22 uF TLE4476D CANL EN GND 100 nF Q2 3 VCC 22 uF 120 Ohm VIO IFX1051 RM 7 CANH 6 TxD RxD CANL optional: common mode choke 100 nF 5 8 Out 1 Out 4 GND ge CANH 100 nF VCC an I In Ch 8.2 Application Information Microcontroller e.g. XMCxx GND I Q1 TLE4476D EN GND - S ub je ct to 2 22 uF 100 nF Q2 3 VCC ar in 7 6 VIO IFX1051 y 22 uF RM CANH TxD RxD CANL im optional: common mode choke Figure 13 CANL 1 4 Out Out In VCC Microcontroller e.g. XMCxx GND 2 Pr CANH 8 100 nF 100 nF GND el 120 Ohm 5 example design Application circuit Preliminary Data Sheet 26 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 8.3 Application Information Examples for Mode Changes Changing the status on the RM input pin triggers a change of the operating mode, disregarding the actual signal on the CANH, CANL and TxD pins (see also Chapter 4.2). Mode changes are triggered by the RM pin, when the device IFX1051 is fully supplied. Setting the RM pin to logical “low” changes the mode of operation to normal-operating mode: • The mode change is executed independently of the signal on the HS CAN bus. The CANH, CANL inputs may be either “dominant” or “recessive”. They can be also permanently shorted to GND or VCC. • A mode change is performed independently of the signal on the TxD input. The TxD input may be either logical “high” or “low”. ge Analog to that, changing the RM input pin to logical “high” changes the mode of operation to the receive-only mode independent on the signals at the CANH, CANL and TxD pins. an Note: In case the TxD signal is “low” setting the RM input pin to logical “low” changes the operating mode of the device to normal-operating mode and drives a “dominant” signal to the HS CAN bus. Pr el im in ar y - S ub je ct to Ch Note: The TxD time-out is only effective in normal-operating mode. The TxD time-out timer starts when the IFX1051 enters normal-operating mode and the TxD input is set to logical “low”. Preliminary Data Sheet 27 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 8.3.1 Application Information Mode Change while the TxD Signal is “low” an ge The example in Figure 14 shows a mode change to normal-operating mode while the TxD input is logical “low”. The HS CAN signal is “recessive”, assuming all other HS CAN bus subscribers are also sending a “recessive” bus signal. While the transceiver IFX1051 is in receive-only mode the transmitter is turned off. The IFX1051 drives no signal to the HS CAN bus. The normal-mode receiver is active in receive-only mode and the RxD indicates the “recessive” signal on the HS CAN bus with a logical “high” output signal. Changing the RM to logical “low” turns the mode of operation to normal-operating mode, while the TxD input remains logical “low”. The transmitter remains disabled until the mode change is completed. The normal-mode receiver remains active also during the mode change. In normal-operating mode the transmitter becomes active and the logical “low” signal on the TxD input drives a “dominant” signal to the HS CAN bus. The “dominant” bus signal is indicated on the RxD output by a logical “low” signal. Changing the RM pin back to logical “high”, disables the transmitter. The normal-mode receiver and the RxD output remain active and the “recessive” bus signal is indicated on the RxD output by a logical “high” signal. Ch Note: The signals on the HS CAN bus are “recessive”, the “dominant” signal is generated by the TxD input signal t = tMode - S ub je ct to t = tMode RM TxD t y VDIFF t ar t in RxD im transition normal-operating transition receive-only el receive-only t Pr normal-mode receiver and RxD output active TxD input and transmitter blocked Figure 14 TxD input and transmitter active TxD input and transmitter blocked Example for a mode change while the TxD is “low” Preliminary Data Sheet 28 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 8.3.2 Application Information Mode Change while the Bus Signal is “dominant” an ge The example in Figure 15 shows a mode change while the bus is “dominant” and the TxD input signal is set to logical “high”. While the transceiver IFX1051 is in receive-only mode the transmitter is turned off. The IFX1051 drives no signal to the HS CAN bus. The normal-mode receiver is active in receive-only mode and the RxD indicates the “dominant” signal on the HS CAN bus with a logical “low” output signal. Changing the RM to logical “low” turns the mode of operation to normal-operating mode, while the TxD input remains logical “high”. The transmitter remains disabled until the mode change is completed. The normal-mode receiver remains active also during the mode change. In normal-operating mode the transmitter becomes active, the bus remains “dominant” since the bus signal is driven from another HS CAN bus subscriber. The “dominant” bus signal is indicated on the RxD output by a logical “low” signal. Regardless which mode of operation is selected by the RM input pin, the RxD output indicates the signal on the HS CAN bus. Also during the mode transition from receive-only mode to normal-operating mode or vice versa. Ch Note: The “dominant” signal on the HS CAN bus is set by another HS CAN bus subscriber. t = tMode t = tMode - S ub je ct to RM TxD t t y VDIFF t transition t normal-operating transition receive-only mode im receive-only mode in ar RxD Pr el normal-mode receiver and RxD output active TxD input and transmitter blocked Figure 15 TxD input and transmitter active TxD input and transmitter blocked Example for a mode change while the HS CAN is “dominant” Preliminary Data Sheet 29 Rev. 0.92, 2015-07-28 IFX1051LE PRELIMINARY 0 +0.05 0.65 ±0.1 1.58 ±0.1 0.38 ±0.1 an 1.63 ±0.1 Z 0.56 ±0.1 0.25 ±0.1 3 ±0.1 0.05 Pin 1 Marking ge 0.3 ±0.1 Ch 3 ±0.1 2.4 ±0.1 0.4 ±0.1 0.1 ±0.1 0.81 ±0.1 1±0.1 Package Outline 0.2 ±0.1 9 Package Outline Pin 1 Marking 0.3 ±0.1 PG-TSON-8-1-PO V01 - S ub je ct to Z (4:1) 0.07 MIN. Figure 16 PG-TSON-8 (Plastic Thin Small Outline Nonleaded PG-TSON-8-1) Green Product (RoHS compliant) Pr el im in ar y To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Preliminary Data Sheet 30 Dimensions in mm Rev. 0.92, 2015-07-28 ge an Ch - S ub je ct to ar in Published by Infineon Technologies AG 81726 Munich, Germany © 2006 Infineon Technologies AG All Rights Reserved. y Edition 2015-07-28 im Legal Disclaimer Information Pr el The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. The Infineon Technologies component described in this Data Sheet may be used in life-support devices or systems and/or automotive, aviation and aerospace applications or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that lifesupport automotive, aviation and aerospace device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.